Merge tag 'omap-for-v4.9/dt-pt2-signed' of...

Merge tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt

Pull "omap dts updates for v4.9 merge window, part 2" from Tony Lindgren:

Part two of device tree changes for omaps for v4.9 merge window. This
is mostly usability and non-critical fixes except for the addition of
beagleboard-x15 rev B1 support:

- Fix omap4 pandaboard SDIO WLAN latencies in idle mode by enabling wakeirq

- Usability fixes for WLAN, USB, LEDs and power button on omap5 boards

- Remove am57xx beagleboard-x15 pinmux configuration as the processor requires
  that it's done in IO isolation in bootloader except for MMC and DCAN

- Add support for beagleboard-x15 rev B1 by moving most of the
  configuration to am57xx-beagle-x15-common.dtsi

- Enable support for more than 2GB of memory for omap5 with LPAE with
  #address-cells

- Fix omap3-gta04 backlight PWM frequency until the PWM driver

- Revert am335x dts changes related to cpufreq as the driver changes
  still have not merged and the dts changes broke cpufreq

* tag 'omap-for-v4.9/dt-pt2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  Revert "ARM: dts: dra7: Move to operating-points-v2 table"
  Revert "ARM: dts: am33xx: Move to operating-points-v2 table and ti-cpufreq driver"
  Revert "ARM: dts: am335x-boneblack: Enable 1GHz OPP for cpu"
  ARM: dts: omap3-gta04: reduce panel backlight PWM frequency to 83Hz
  ARM: dts: Add support for more than 2GB of memory for omap5
  ARM: dts: am57xx-beagle-x15: Add support for rev B1
  ARM: dts: am57xx-beagle-x15: Remove pinmux configurations for erratum i869
  ARM: dts: Fix LEDs for igepv5
  ARM: dts: Add power button support for igepv5
  ARM: dts: Configure omap5 OTG ID pin
  ARM: dts: ARM: dts: Fix omap5 SDIO dat1 interrupt
  ARM: dts: Configure panda SDIO WLAN wakeirq

arch/arm/boot/dts/Makefile

@@ -584,6 +584,7 @@ dtb-$(CONFIG_SOC_OMAP5) += \
 	omap5-uevm.dtb
 dtb-$(CONFIG_SOC_DRA7XX) += \
 	am57xx-beagle-x15.dtb \
+	am57xx-beagle-x15-revb1.dtb \
 	am57xx-cl-som-am57x.dtb \
 	am57xx-sbc-am57x.dtb \
 	am572x-idk.dtb \

arch/arm/boot/dts/am335x-boneblack.dts

@@ -33,17 +33,6 @@ &mmc2 {
 	status = "okay";
 };
 
-&cpu0_opp_table {
-	/*
-	 * All PG 2.0 silicon may not support 1GHz but some of the early
-	 * BeagleBone Blacks have PG 2.0 silicon which is guaranteed
-	 * to support 1GHz OPP so enable it for PG 2.0 on this board.
-	 */
-	oppnitro@1000000000 {
-		opp-supported-hw = <0x06 0x0100>;
-	};
-};
-
 &am33xx_pinmux {
 	nxp_hdmi_bonelt_pins: nxp_hdmi_bonelt_pins {
 		pinctrl-single,pins = <

arch/arm/boot/dts/am33xx.dtsi

@@ -45,9 +45,19 @@ cpu@0 {
 			device_type = "cpu";
 			reg = <0>;
 
-			operating-points-v2 = <&cpu0_opp_table>;
-			ti,syscon-efuse = <&scm_conf 0x7fc 0x1fff 0>;
-			ti,syscon-rev = <&scm_conf 0x600>;
+			/*
+			 * To consider voltage drop between PMIC and SoC,
+			 * tolerance value is reduced to 2% from 4% and
+			 * voltage value is increased as a precaution.
+			 */
+			operating-points = <
+				/* kHz    uV */
+				720000  1285000
+				600000  1225000
+				500000  1125000
+				275000  1125000
+			>;
+			voltage-tolerance = <2>; /* 2 percentage */
 
 			clocks = <&dpll_mpu_ck>;
 			clock-names = "cpu";
@@ -56,78 +66,6 @@ cpu@0 {
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
-		compatible = "operating-points-v2";
-
-		/*
-		 * The three following nodes are marked with opp-suspend
-		 * because the can not be enabled simultaneously on a
-		 * single SoC.
-		 */
-		opp50@300000000 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <950000 931000 969000>;
-			opp-supported-hw = <0x06 0x0010>;
-			opp-suspend;
-		};
-
-		opp100@275000000 {
-			opp-hz = /bits/ 64 <275000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x01 0x00FF>;
-			opp-suspend;
-		};
-
-		opp100@300000000 {
-			opp-hz = /bits/ 64 <300000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x06 0x0020>;
-			opp-suspend;
-		};
-
-		opp100@500000000 {
-			opp-hz = /bits/ 64 <500000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		opp100@600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <1100000 1078000 1122000>;
-			opp-supported-hw = <0x06 0x0040>;
-		};
-
-		opp120@600000000 {
-			opp-hz = /bits/ 64 <600000000>;
-			opp-microvolt = <1200000 1176000 1224000>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		opp120@720000000 {
-			opp-hz = /bits/ 64 <720000000>;
-			opp-microvolt = <1200000 1176000 1224000>;
-			opp-supported-hw = <0x06 0x0080>;
-		};
-
-		oppturbo@720000000 {
-			opp-hz = /bits/ 64 <720000000>;
-			opp-microvolt = <1260000 1234800 1285200>;
-			opp-supported-hw = <0x01 0xFFFF>;
-		};
-
-		oppturbo@800000000 {
-			opp-hz = /bits/ 64 <800000000>;
-			opp-microvolt = <1260000 1234800 1285200>;
-			opp-supported-hw = <0x06 0x0100>;
-		};
-
-		oppnitro@1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1325000 1298500 1351500>;
-			opp-supported-hw = <0x04 0x0200>;
-		};
-	};
-
 	pmu {
 		compatible = "arm,cortex-a8-pmu";
 		interrupts = <3>;

arch/arm/boot/dts/am57xx-beagle-x15-revb1.dts

+/*
+ * Copyright (C) 2014-2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "am57xx-beagle-x15-common.dtsi"
+
+/ {
+	model = "TI AM5728 BeagleBoard-X15 rev B1";
+};
+
+&tpd12s015 {
+	gpios = <&gpio7 10 GPIO_ACTIVE_HIGH>,	/* gpio7_10, CT CP HPD */
+		<&gpio2 30 GPIO_ACTIVE_HIGH>,	/* gpio2_30, LS OE */
+		<&gpio7 12 GPIO_ACTIVE_HIGH>;	/* gpio7_12/sp1_cs2, HPD */
+};
+
+&mmc1 {
+	vmmc-supply = <&vdd_3v3>;
+	vmmc-aux-supply = <&ldo1_reg>;
+};

arch/arm/boot/dts/dra7.dtsi

@@ -80,9 +80,11 @@ cpu0: cpu@0 {
 			compatible = "arm,cortex-a15";
 			reg = <0>;
 
-			operating-points-v2 = <&cpu0_opp_table>;
-			ti,syscon-efuse = <&scm_wkup 0x20c 0xf80000 19>;
-			ti,syscon-rev = <&scm_wkup 0x204>;
+			operating-points = <
+				/* kHz    uV */
+				1000000	1060000
+				1176000	1160000
+				>;
 
 			clocks = <&dpll_mpu_ck>;
 			clock-names = "cpu";
@@ -96,24 +98,6 @@ cpu0: cpu@0 {
 		};
 	};
 
-	cpu0_opp_table: opp_table0 {
-		compatible = "operating-points-v2";
-		opp-shared;
-
-		opp_nom@1000000000 {
-			opp-hz = /bits/ 64 <1000000000>;
-			opp-microvolt = <1060000 850000 1150000>;
-			opp-supported-hw = <0xFF 0x01>;
-			opp-suspend;
-		};
-
-		opp_od@1176000000 {
-			opp-hz = /bits/ 64 <1176000000>;
-			opp-microvolt = <1160000 885000 1160000>;
-			opp-supported-hw = <0xFF 0x02>;
-		};
-	};
-
 	/*
 	 * The soc node represents the soc top level view. It is used for IPs
 	 * that are not memory mapped in the MPU view or for the MPU itself.

arch/arm/boot/dts/dra74x.dtsi

@@ -17,7 +17,6 @@ cpu@1 {
 			device_type = "cpu";
 			compatible = "arm,cortex-a15";
 			reg = <1>;
-			operating-points-v2 = <&cpu0_opp_table>;
 		};
 	};
 

arch/arm/boot/dts/omap3-gta04.dtsi

@@ -102,7 +102,7 @@ lcd_in: endpoint {
 
 	backlight {
 		compatible = "pwm-backlight";
-		pwms = <&pwm11 0 2000000 0>;
+		pwms = <&pwm11 0 12000000 0>;
 		pwm-names = "backlight";
 		brightness-levels = <0 11 20 30 40 50 60 70 80 90 100>;
 		default-brightness-level = <9>;	/* => 90 */

arch/arm/boot/dts/omap4-panda-common.dtsi

@@ -446,6 +446,8 @@ &mmc5 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&wl12xx_pins>;
 	vmmc-supply = <&wl12xx_vmmc>;
+	interrupts-extended = <&wakeupgen GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH
+			       &omap4_pmx_core 0x10e>;
 	non-removable;
 	bus-width = <4>;
 	cap-power-off-card;

arch/arm/boot/dts/omap5-board-common.dtsi

@@ -77,16 +77,6 @@ hsusb3_phy: hsusb3_phy {
 		reset-gpios = <&gpio3 15 GPIO_ACTIVE_LOW>; /* gpio3_79 ETH_NRESET */
 	};
 
-	leds {
-		compatible = "gpio-leds";
-		led1 {
-			label = "omap5:blue:usr1";
-			gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
-			linux,default-trigger = "heartbeat";
-			default-state = "off";
-		};
-	};
-
 	tpd12s015: encoder {
 		compatible = "ti,tpd12s015";
 
@@ -332,7 +322,7 @@ OMAP5_IOPAD(0x05a, PIN_OUTPUT | MUX_MODE0) /* fref_clk1_out, USB hub clk */
 
 	wlcore_irq_pin: pinmux_wlcore_irq_pin {
 		pinctrl-single,pins = <
-			OMAP5_IOPAD(0x40, PIN_INPUT_PULLUP | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
+			OMAP5_IOPAD(0x40, PIN_INPUT | MUX_MODE6)	/* llia_wakereqin.gpio1_wk14 */
 		>;
 	};
 };
@@ -355,15 +345,17 @@ &mmc3 {
 	non-removable;
 	cap-power-off-card;
 	pinctrl-names = "default";
-	pinctrl-0 = <&mmc3_pins &wlcore_irq_pin>;
-	interrupts-extended = <&gic GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
-			       &omap5_pmx_core 0x168>;
+	pinctrl-0 = <&mmc3_pins>;
+	interrupts-extended = <&wakeupgen GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH
+			       &omap5_pmx_core 0x16a>;
 
 	#address-cells = <1>;
 	#size-cells = <0>;
 	wlcore: wlcore@2 {
 		compatible = "ti,wl1271";
 		reg = <2>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&wlcore_irq_pin>;
 		interrupt-parent = <&gpio1>;
 		interrupts = <14 IRQ_TYPE_LEVEL_HIGH>;	/* gpio 14 */
 		ref-clock-frequency = <26000000>;
@@ -391,14 +383,23 @@ palmas: palmas@48 {
 		interrupt-controller;
 		#interrupt-cells = <2>;
 		ti,system-power-controller;
+		ti,mux-pad1 = <0xa1>;
+		ti,mux-pad2 = <0x1b>;
 		pinctrl-names = "default";
 		pinctrl-0 = <&palmas_sys_nirq_pins &palmas_msecure_pins>;
 
+		palmas_gpio: gpio {
+			compatible = "ti,palmas-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+		};
+
 		extcon_usb3: palmas_usb {
 			compatible = "ti,palmas-usb-vid";
 			ti,enable-vbus-detection;
 			ti,enable-id-detection;
 			ti,wakeup;
+			id-gpios = <&palmas_gpio 0 GPIO_ACTIVE_HIGH>;
 		};
 
 		clk32kgaudio: palmas_clk32k@1 {

arch/arm/boot/dts/omap5-cm-t54.dts

@@ -13,7 +13,7 @@ / {
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0x80000000 0x7F000000>; /* 2048 MB */
+		reg = <0 0x80000000 0 0x7f000000>; /* 2048 MB */
 	};
 
 	aliases {

arch/arm/boot/dts/omap5-igep0050.dts

@@ -7,6 +7,7 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/input/input.h>
 #include "omap5-board-common.dtsi"
 
 / {
@@ -15,7 +16,38 @@ / {
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0x80000000 0x7f000000>; /* 2032 MB */
+		reg = <0x0 0x80000000 0 0x7f000000>;	/* 2032 MB */
+	};
+
+	gpio_keys {
+                compatible = "gpio-keys";
+		pinctrl-0 = <&power_button_pin>;
+		pinctrl-names = "default";
+
+		power-button {
+			label = "Power Button";
+			linux,code = <KEY_POWER>;
+			gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led@1 {
+			label = "board:green:usr0";
+			gpios = <&tca6416 1 0>;
+			default-state = "off";
+		};
+		led@2 {
+			label = "board:red:usr1";
+			gpios = <&tca6416 2 0>;
+			default-state = "off";
+		};
+		led@3 {
+			label = "board:blue:usr1";
+			gpios = <&tca6416 3 0>;
+			default-state = "off";
+		};
 	};
 };
 
@@ -58,6 +90,12 @@ OMAP5_IOPAD(0x0f8, PIN_INPUT | MUX_MODE0)	/* i2c4_scl */
 			OMAP5_IOPAD(0x0fa, PIN_INPUT | MUX_MODE0)	/* i2c4_sda */
 		>;
 	};
+
+	power_button_pin: pinctrl_power_button_pin {
+		pinctrl-single,pins = <
+			OMAP5_IOPAD(0x086, PIN_INPUT | MUX_MODE6)	/* gpio4_118 */
+		>;
+	};
 };
 
 &tpd12s015 {

arch/arm/boot/dts/omap5-uevm.dts

@@ -15,7 +15,17 @@ / {
 
 	memory@80000000 {
 		device_type = "memory";
-		reg = <0x80000000 0x7F000000>; /* 2032 MB */
+		reg = <0 0x80000000 0 0x7f000000>; /* 2032 MB */
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		led1 {
+			label = "omap5:blue:usr1";
+			gpios = <&gpio5 25 GPIO_ACTIVE_HIGH>; /* gpio5_153 D1 LED */
+			linux,default-trigger = "heartbeat";
+			default-state = "off";
+		};
 	};
 };
 
@@ -61,3 +71,7 @@ &twl6040_pins {
 		OMAP5_IOPAD(0x1be, PIN_OUTPUT | MUX_MODE6)	/* mcspi1_somi.gpio5_141 */
 	>;
 };
+
+&wlcore {
+	compatible = "ti,wl1837";
+};

arch/arm/boot/dts/omap5.dtsi

@@ -12,8 +12,8 @@
 #include <dt-bindings/pinctrl/omap.h>
 
 / {
-	#address-cells = <1>;
-	#size-cells = <1>;
+	#address-cells = <2>;
+	#size-cells = <2>;
 
 	compatible = "ti,omap5";
 	interrupt-parent = <&wakeupgen>;
@@ -90,10 +90,10 @@ gic: interrupt-controller@48211000 {
 		compatible = "arm,cortex-a15-gic";
 		interrupt-controller;
 		#interrupt-cells = <3>;
-		reg = <0x48211000 0x1000>,
-		      <0x48212000 0x1000>,
-		      <0x48214000 0x2000>,
-		      <0x48216000 0x2000>;
+		reg = <0 0x48211000 0 0x1000>,
+		      <0 0x48212000 0 0x1000>,
+		      <0 0x48214000 0 0x2000>,
+		      <0 0x48216000 0 0x2000>;
 		interrupt-parent = <&gic>;
 	};
 
@@ -101,7 +101,7 @@ wakeupgen: interrupt-controller@48281000 {
 		compatible = "ti,omap5-wugen-mpu", "ti,omap4-wugen-mpu";
 		interrupt-controller;
 		#interrupt-cells = <3>;
-		reg = <0x48281000 0x1000>;
+		reg = <0 0x48281000 0 0x1000>;
 		interrupt-parent = <&gic>;
 	};
 
@@ -129,11 +129,11 @@ ocp {
 		compatible = "ti,omap5-l3-noc", "simple-bus";
 		#address-cells = <1>;
 		#size-cells = <1>;
-		ranges;
+		ranges = <0 0 0 0xc0000000>;
 		ti,hwmods = "l3_main_1", "l3_main_2", "l3_main_3";
-		reg = <0x44000000 0x2000>,
-		      <0x44800000 0x3000>,
-		      <0x45000000 0x4000>;
+		reg = <0 0x44000000 0 0x2000>,
+		      <0 0x44800000 0 0x3000>,
+		      <0 0x45000000 0 0x4000>;
 		interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
 			     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
 
@@ -863,7 +863,7 @@ usb3: omap_dwc3@4a020000 {
 			#size-cells = <1>;
 			utmi-mode = <2>;
 			ranges;
-			dwc3@4a030000 {
+			dwc3: dwc3@4a030000 {
 				compatible = "snps,dwc3";
 				reg = <0x4a030000 0x10000>;
 				interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,