Staging: rtl8192e: Make arrays const

Signed-off-by: Mike McCormack <mikem@ring3k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/rtl8192e/ieee80211/rtl819x_HTProc.c

@@ -29,18 +29,18 @@ u16 MCS_DATA_RATE[2][2][77] =
 			660, 450, 540, 630, 540, 630, 720, 810, 720, 810, 900, 900, 990}	}	// Short GI, 40MHz
 	};
 
-static u8 UNKNOWN_BORADCOM[3] = {0x00, 0x14, 0xbf};
-static u8 LINKSYSWRT330_LINKSYSWRT300_BROADCOM[3] = {0x00, 0x1a, 0x70};
-static u8 LINKSYSWRT350_LINKSYSWRT150_BROADCOM[3] = {0x00, 0x1d, 0x7e};
+static const u8 UNKNOWN_BORADCOM[3] = {0x00, 0x14, 0xbf};
+static const u8 LINKSYSWRT330_LINKSYSWRT300_BROADCOM[3] = {0x00, 0x1a, 0x70};
+static const u8 LINKSYSWRT350_LINKSYSWRT150_BROADCOM[3] = {0x00, 0x1d, 0x7e};
 //static u8 NETGEAR834Bv2_BROADCOM[3] = {0x00, 0x1b, 0x2f};
-static u8 BELKINF5D8233V1_RALINK[3] = {0x00, 0x17, 0x3f};	//cosa 03202008
-static u8 BELKINF5D82334V3_RALINK[3] = {0x00, 0x1c, 0xdf};
-static u8 PCI_RALINK[3] = {0x00, 0x90, 0xcc};
-static u8 EDIMAX_RALINK[3] = {0x00, 0x0e, 0x2e};
-static u8 AIRLINK_RALINK[3] = {0x00, 0x18, 0x02};
-static u8 DLINK_ATHEROS[3] = {0x00, 0x1c, 0xf0};
-static u8 CISCO_BROADCOM[3] = {0x00, 0x17, 0x94};
-static u8 LINKSYS_MARVELL_4400N[3] = {0x00, 0x14, 0xa4};
+static const u8 BELKINF5D8233V1_RALINK[3] = {0x00, 0x17, 0x3f};
+static const u8 BELKINF5D82334V3_RALINK[3] = {0x00, 0x1c, 0xdf};
+static const u8 PCI_RALINK[3] = {0x00, 0x90, 0xcc};
+static const u8 EDIMAX_RALINK[3] = {0x00, 0x0e, 0x2e};
+static const u8 AIRLINK_RALINK[3] = {0x00, 0x18, 0x02};
+static const u8 DLINK_ATHEROS[3] = {0x00, 0x1c, 0xf0};
+static const u8 CISCO_BROADCOM[3] = {0x00, 0x17, 0x94};
+static const u8 LINKSYS_MARVELL_4400N[3] = {0x00, 0x14, 0xa4};
 
 // 2008/04/01 MH For Cisco G mode RX TP We need to change FW duration. Should we put the
 // code in other place??