xhci: rename temp and temp1 variables

temp and temp1 variables are used for port status (portsc) and
command register. Give them more descriptive names

No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/usb/host/xhci-ring.c

@@ -1572,7 +1572,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 {
 	struct usb_hcd *hcd;
 	u32 port_id;
-	u32 temp, temp1;
+	u32 portsc, cmd_reg;
 	int max_ports;
 	int slot_id;
 	unsigned int faked_port_index;
@@ -1636,26 +1636,26 @@ static void handle_port_status(struct xhci_hcd *xhci,
 	/* Find the faked port hub number */
 	faked_port_index = find_faked_portnum_from_hw_portnum(hcd, xhci,
 			port_id);
+	portsc = readl(port_array[faked_port_index]);
 
-	temp = readl(port_array[faked_port_index]);
 	if (hcd->state == HC_STATE_SUSPENDED) {
 		xhci_dbg(xhci, "resume root hub\n");
 		usb_hcd_resume_root_hub(hcd);
 	}
 
-	if (hcd->speed >= HCD_USB3 && (temp & PORT_PLS_MASK) == XDEV_INACTIVE)
+	if (hcd->speed >= HCD_USB3 && (portsc & PORT_PLS_MASK) == XDEV_INACTIVE)
 		bus_state->port_remote_wakeup &= ~(1 << faked_port_index);
 
-	if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_RESUME) {
+	if ((portsc & PORT_PLC) && (portsc & PORT_PLS_MASK) == XDEV_RESUME) {
 		xhci_dbg(xhci, "port resume event for port %d\n", port_id);
 
-		temp1 = readl(&xhci->op_regs->command);
-		if (!(temp1 & CMD_RUN)) {
+		cmd_reg = readl(&xhci->op_regs->command);
+		if (!(cmd_reg & CMD_RUN)) {
 			xhci_warn(xhci, "xHC is not running.\n");
 			goto cleanup;
 		}
 
-		if (DEV_SUPERSPEED_ANY(temp)) {
+		if (DEV_SUPERSPEED_ANY(portsc)) {
 			xhci_dbg(xhci, "remote wake SS port %d\n", port_id);
 			/* Set a flag to say the port signaled remote wakeup,
 			 * so we can tell the difference between the end of
@@ -1683,8 +1683,8 @@ static void handle_port_status(struct xhci_hcd *xhci,
 		}
 	}
 
-	if ((temp & PORT_PLC) && (temp & PORT_PLS_MASK) == XDEV_U0 &&
-			DEV_SUPERSPEED_ANY(temp)) {
+	if ((portsc & PORT_PLC) && (portsc & PORT_PLS_MASK) == XDEV_U0 &&
+			DEV_SUPERSPEED_ANY(portsc)) {
 		xhci_dbg(xhci, "resume SS port %d finished\n", port_id);
 		/* We've just brought the device into U0 through either the
 		 * Resume state after a device remote wakeup, or through the
@@ -1714,7 +1714,7 @@ static void handle_port_status(struct xhci_hcd *xhci,
 	 * RExit to a disconnect state).  If so, let the the driver know it's
 	 * out of the RExit state.
 	 */
-	if (!DEV_SUPERSPEED_ANY(temp) &&
+	if (!DEV_SUPERSPEED_ANY(portsc) &&
 			test_and_clear_bit(faked_port_index,
 				&bus_state->rexit_ports)) {
 		complete(&bus_state->rexit_done[faked_port_index]);