Merge kroah.com:/home/greg/linux/BK/bleeding_edge-2.5

into kroah.com:/home/greg/linux/BK/gregkh-2.5

Documentation/usb/usb-serial.txt

@@ -41,17 +41,13 @@ SPECIFIC DEVICES SUPPORTED
 ConnectTech WhiteHEAT 4 port converter
 
   ConnectTech has been very forthcoming with information about their
-  device, including providing a unit to test with. This driver will end up
-  being fully supported.
+  device, including providing a unit to test with.
 
-  Current status:
-    The device's firmware is downloaded on connection, the new firmware 
-    runs properly and all four ports are successfully recognized and connected.
-    Data can be sent and received through the device on all ports.
-    Hardware flow control needs to be implemented.
+  The driver is officially supported by Connect Tech Inc.
+  http://www.connecttech.com
 
-  For any questions or problems with this driver, please contact Greg
-  Kroah-Hartman at greg@kroah.com
+  For any questions or problems with this driver, please contact
+  Stuart MacDonald at stuartm@connecttech.com
 
 
 HandSpring Visor, Palm USB, and Clié USB driver

MAINTAINERS

@@ -1830,6 +1830,14 @@ L:	linux-usb-devel@lists.sourceforge.net
 W:	http://www.kroah.com/linux/
 S:	Maintained
 
+USB SERIAL WHITEHEAT DRIVER
+P:	Stuart MacDonald
+M:	stuartm@connecttech.com
+L:	linux-usb-users@lists.sourceforge.net
+L:	linux-usb-devel@lists.sourceforge.net
+W:	http://www.connecttech.com
+S:	Supported
+
 USB SUBSYSTEM
 P:	Greg Kroah-Hartman
 M:	greg@kroah.com

drivers/usb/core/usb.c

@@ -1142,6 +1142,7 @@ int usb_new_device(struct usb_device *dev, struct device *parent)
 		struct usb_interface_descriptor *desc = interface->altsetting;
 
 		interface->dev.parent = &dev->dev;
+		interface->dev.driver = NULL;
 		interface->dev.bus = &usb_bus_type;
 		sprintf (&interface->dev.bus_id[0], "%d-%s:%d",
 			 dev->bus->busnum, dev->devpath,

drivers/usb/host/ehci-dbg.c

@@ -79,7 +79,7 @@ static void dbg_hcc_params (struct ehci_hcd *ehci, char *label)
 
 	if (HCC_EXT_CAPS (params)) {
 		// EHCI 0.96 ... could interpret these (legacy?)
-		dbg ("%s extended capabilities at pci %d",
+		dbg ("%s extended capabilities at pci %2x",
 			label, HCC_EXT_CAPS (params));
 	}
 	if (HCC_ISOC_CACHE (params)) {
@@ -546,6 +546,18 @@ show_registers (struct device *dev, char *buf, size_t count, loff_t off)
 		next += temp;
 	}
 
+#ifdef EHCI_STATS
+	temp = snprintf (next, size, "irq normal %ld err %ld reclaim %ld\n",
+		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim);
+	size -= temp;
+	next += temp;
+
+	temp = snprintf (next, size, "complete %ld unlink %ld qpatch %ld\n",
+		ehci->stats.complete, ehci->stats.unlink, ehci->stats.qpatch);
+	size -= temp;
+	next += temp;
+#endif
+
 	spin_unlock_irqrestore (&ehci->lock, flags);
 
 	return count - size;

drivers/usb/host/ehci-hcd.c

@@ -63,8 +63,7 @@
  * First was PCMCIA, like ISA; then CardBus, which is PCI.
  * Next comes "CardBay", using USB 2.0 signals.
  *
- * Contains additional contributions by: Brad Hards, Rory Bolt, ...
- *
+ * Contains additional contributions by Brad Hards, Rory Bolt, and others.
  * Special thanks to Intel and VIA for providing host controllers to
  * test this driver on, and Cypress (including In-System Design) for
  * providing early devices for those host controllers to talk to!
@@ -93,14 +92,20 @@
  * 2001-June	Works with usb-storage and NEC EHCI on 2.4
  */
 
-#define DRIVER_VERSION "2002-Aug-28"
+#define DRIVER_VERSION "2002-Sep-23"
 #define DRIVER_AUTHOR "David Brownell"
 #define DRIVER_DESC "USB 2.0 'Enhanced' Host Controller (EHCI) Driver"
 
+static const char	hcd_name [] = "ehci-hcd";
+
 
 // #define EHCI_VERBOSE_DEBUG
 // #define have_split_iso
 
+#ifdef DEBUG
+#define EHCI_STATS
+#endif
+
 #define INTR_AUTOMAGIC		/* to be removed later in 2.5 */
 
 /* magic numbers that can affect system performance */
@@ -118,6 +123,12 @@ static int log2_irq_thresh = 0;		// 0 to 6
 MODULE_PARM (log2_irq_thresh, "i");
 MODULE_PARM_DESC (log2_irq_thresh, "log2 IRQ latency, 1-64 microframes");
 
+/* allow irqs at least every N URB completions */
+static int max_completions = 16;
+MODULE_PARM (max_completions, "i");
+MODULE_PARM_DESC (max_completions,
+		"limit for urb completions called with irqs disenabled");
+
 #define	INTR_MASK (STS_IAA | STS_FATAL | STS_ERR | STS_INT)
 
 /*-------------------------------------------------------------------------*/
@@ -426,11 +437,10 @@ static int ehci_start (struct usb_hcd *hcd)
         /* PCI Serial Bus Release Number is at 0x60 offset */
 	pci_read_config_byte (hcd->pdev, 0x60, &tempbyte);
 	temp = readw (&ehci->caps->hci_version);
-	info ("USB %x.%x support enabled, EHCI rev %x.%02x",
-	      ((tempbyte & 0xf0)>>4),
-	      (tempbyte & 0x0f),
-	       temp >> 8,
-	       temp & 0xff);
+	info ("USB %x.%x support enabled, EHCI rev %x.%02x, %s %s",
+	      ((tempbyte & 0xf0)>>4), (tempbyte & 0x0f),
+	       temp >> 8, temp & 0xff,
+	       hcd_name, DRIVER_VERSION);
 
 	/*
 	 * From here on, khubd concurrently accesses the root
@@ -441,11 +451,7 @@ static int ehci_start (struct usb_hcd *hcd)
 	 */
 	usb_connect (udev);
 	udev->speed = USB_SPEED_HIGH;
-#if LINUX_VERSION_CODE < KERNEL_VERSION(2,5,32)
-	if (usb_new_device (udev) != 0) {
-#else
-	if (usb_register_root_hub (udev, &ehci->hcd.pdev->dev) != 0) {
-#endif
+	if (hcd_register_root (hcd) != 0) {
 		if (hcd->state == USB_STATE_RUNNING)
 			ehci_ready (ehci);
 		ehci_reset (ehci);
@@ -487,6 +493,13 @@ static void ehci_stop (struct usb_hcd *hcd)
 	ehci_tasklet ((unsigned long) ehci);
 	ehci_mem_cleanup (ehci);
 
+#ifdef	EHCI_STATS
+	dbg ("irq normal %ld err %ld reclaim %ld",
+		ehci->stats.normal, ehci->stats.error, ehci->stats.reclaim);
+	dbg ("complete %ld unlink %ld qpatch %ld",
+		ehci->stats.complete, ehci->stats.unlink, ehci->stats.qpatch);
+#endif
+
 	dbg_status (ehci, "ehci_stop completed", readl (&ehci->regs->status));
 }
 
@@ -591,21 +604,16 @@ dbg ("%s: resume port %d", hcd_to_bus (hcd)->bus_name, i);
 static void ehci_tasklet (unsigned long param)
 {
 	struct ehci_hcd		*ehci = (struct ehci_hcd *) param;
-	unsigned long		flags;
 
-	// FIXME don't pass flags; on sparc they aren't really flags.
-	// qh_completions can just leave irqs blocked,
-	// then have scan_async() allow IRQs if it's very busy 
-
-	spin_lock_irqsave (&ehci->lock, flags);
+	spin_lock_irq (&ehci->lock);
 
 	if (ehci->reclaim_ready)
-		flags = end_unlink_async (ehci, flags);
-	flags = scan_async (ehci, flags);
+		end_unlink_async (ehci);
+	scan_async (ehci);
 	if (ehci->next_uframe != -1)
-		flags = scan_periodic (ehci, flags);
+		scan_periodic (ehci);
 
-	spin_unlock_irqrestore (&ehci->lock, flags);
+	spin_unlock_irq (&ehci->lock);
 }
 
 /*-------------------------------------------------------------------------*/
@@ -639,11 +647,17 @@ static void ehci_irq (struct usb_hcd *hcd)
 	/* INT, ERR, and IAA interrupt rates can be throttled */
 
 	/* normal [4.15.1.2] or error [4.15.1.1] completion */
-	if (likely ((status & (STS_INT|STS_ERR)) != 0))
+	if (likely ((status & (STS_INT|STS_ERR)) != 0)) {
+		if (likely ((status & STS_ERR) == 0))
+			COUNT (ehci->stats.normal);
+		else
+			COUNT (ehci->stats.error);
 		bh = 1;
+	}
 
 	/* complete the unlinking of some qh [4.15.2.3] */
 	if (status & STS_IAA) {
+		COUNT (ehci->stats.reclaim);
 		ehci->reclaim_ready = 1;
 		bh = 1;
 	}
@@ -765,10 +779,10 @@ static int ehci_urb_dequeue (struct usb_hcd *hcd, struct urb *urb)
 		spin_lock_irqsave (&ehci->lock, flags);
 		if (qh->qh_state == QH_STATE_LINKED) {
 			/* messy, can spin or block a microframe ... */
-			flags = intr_deschedule (ehci, qh, 1, flags);
+			intr_deschedule (ehci, qh, 1);
 			/* qh_state == IDLE */
 		}
-		flags = qh_completions (ehci, qh, flags);
+		qh_completions (ehci, qh);
 
 		/* reschedule QH iff another request is queued */
 		if (!list_empty (&qh->qtd_list)
@@ -881,8 +895,6 @@ static void ehci_free_config (struct usb_hcd *hcd, struct usb_device *udev)
 
 /*-------------------------------------------------------------------------*/
 
-static const char	hcd_name [] = "ehci-hcd";
-
 static const struct hc_driver ehci_driver = {
 	.description =		hcd_name,
 

drivers/usb/host/ehci-hub.c

@@ -239,7 +239,8 @@ static int ehci_hub_control (
 
 		/* whoever resets must GetPortStatus to complete it!! */
 		if ((temp & PORT_RESET)
-				&& jiffies > ehci->reset_done [wIndex]) {
+				&& time_after (jiffies,
+					ehci->reset_done [wIndex])) {
 			status |= 1 << USB_PORT_FEAT_C_RESET;
 
 			/* force reset to complete */

drivers/usb/host/ehci-q.c

@@ -158,16 +158,13 @@ static inline void qtd_copy_status (struct urb *urb, size_t length, u32 token)
 	}
 }
 
-/* urb->lock ignored from here on (hcd is done with urb) */
-
-static unsigned long ehci_urb_done (
-	struct ehci_hcd		*ehci,
-	struct urb		*urb,
-	unsigned long		flags
-) {
+static void ehci_urb_done (struct ehci_hcd *ehci, struct urb *urb)
+{
 #ifdef	INTR_AUTOMAGIC
 	struct urb		*resubmit = 0;
 	struct usb_device	*dev = 0;
+
+	static int ehci_urb_enqueue (struct usb_hcd *, struct urb *, int);
 #endif
 
 	if (likely (urb->hcpriv != 0)) {
@@ -199,8 +196,15 @@ static unsigned long ehci_urb_done (
 			urb->status = 0;
 	}
 
+	if (likely (urb->status == 0))
+		COUNT (ehci->stats.complete);
+	else if (urb->status == -ECONNRESET || urb->status == -ENOENT)
+		COUNT (ehci->stats.unlink);
+	else
+		COUNT (ehci->stats.error);
+
 	/* complete() can reenter this HCD */
-	spin_unlock_irqrestore (&ehci->lock, flags);
+	spin_unlock (&ehci->lock);
 	usb_hcd_giveback_urb (&ehci->hcd, urb);
 
 #ifdef	INTR_AUTOMAGIC
@@ -222,24 +226,25 @@ static unsigned long ehci_urb_done (
 	}
 #endif
 
-	spin_lock_irqsave (&ehci->lock, flags);
-	return flags;
+	spin_lock (&ehci->lock);
 }
 
 
 /*
  * Process and free completed qtds for a qh, returning URBs to drivers.
- * Chases up to qh->hw_current, returns irqsave flags (maybe modified).
+ * Chases up to qh->hw_current.  Returns number of completions called,
+ * indicating how much "real" work we did.
  */
-static unsigned long
-qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh, unsigned long flags)
+static unsigned
+qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh)
 {
 	struct ehci_qtd		*qtd, *last;
 	struct list_head	*next, *qtd_list = &qh->qtd_list;
 	int			unlink = 0, halted = 0;
+	unsigned		count = 0;
 
 	if (unlikely (list_empty (qtd_list)))
-		return flags;
+		return count;
 
 	/* scan QTDs till end of list, or we reach an active one */
 	for (qtd = list_entry (qtd_list->next, struct ehci_qtd, qtd_list),
@@ -252,8 +257,10 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh, unsigned long flags)
 
 		/* clean up any state from previous QTD ...*/
 		if (last) {
-			if (likely (last->urb != urb))
-				flags = ehci_urb_done (ehci, last->urb, flags);
+			if (likely (last->urb != urb)) {
+				ehci_urb_done (ehci, last->urb);
+				count++;
+			}
 
 			/* qh overlays can have HC's old cached copies of
 			 * next qtd ptrs, if an URB was queued afterwards.
@@ -262,6 +269,7 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh, unsigned long flags)
 					&& last->hw_next != qh->hw_qtd_next) {
 				qh->hw_alt_next = last->hw_alt_next;
 				qh->hw_qtd_next = last->hw_next;
+				COUNT (ehci->stats.qpatch);
 			}
 
 			ehci_qtd_free (ehci, last);
@@ -347,7 +355,8 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh, unsigned long flags)
 
 	/* last urb's completion might still need calling */
 	if (likely (last != 0)) {
-		flags = ehci_urb_done (ehci, last->urb, flags);
+		ehci_urb_done (ehci, last->urb);
+		count++;
 		ehci_qtd_free (ehci, last);
 	}
 
@@ -357,7 +366,7 @@ qh_completions (struct ehci_hcd *ehci, struct ehci_qh *qh, unsigned long flags)
 				struct ehci_qtd, qtd_list));
 	}
 
-	return flags;
+	return count;
 }
 
 /*-------------------------------------------------------------------------*/
@@ -890,8 +899,7 @@ submit_async (
 /* the async qh for the qtds being reclaimed are now unlinked from the HC */
 /* caller must not own ehci->lock */
 
-static unsigned long
-end_unlink_async (struct ehci_hcd *ehci, unsigned long flags)
+static void end_unlink_async (struct ehci_hcd *ehci)
 {
 	struct ehci_qh		*qh = ehci->reclaim;
 
@@ -903,18 +911,15 @@ end_unlink_async (struct ehci_hcd *ehci, unsigned long flags)
 	ehci->reclaim = 0;
 	ehci->reclaim_ready = 0;
 
-	flags = qh_completions (ehci, qh, flags);
+	qh_completions (ehci, qh);
 
 	if (!list_empty (&qh->qtd_list)
 			&& HCD_IS_RUNNING (ehci->hcd.state))
 		qh_link_async (ehci, qh);
 	else
 		qh_put (ehci, qh);		// refcount from async list
-
-	return flags;
 }
 
-
 /* makes sure the async qh will become idle */
 /* caller must own ehci->lock */
 
@@ -944,12 +949,14 @@ static void start_unlink_async (struct ehci_hcd *ehci, struct ehci_qh *qh)
 	if (unlikely (qh == ehci->async && qh->qh_next.qh == qh)) {
 		/* can't get here without STS_ASS set */
 		if (ehci->hcd.state != USB_STATE_HALT) {
-			if (cmd & CMD_PSE) {
-				writel (cmd & ~CMD_ASE, &ehci->regs->command);
-				(void) handshake (&ehci->regs->status,
-						  STS_ASS, 0, 150);
-			} else
-				ehci_ready (ehci);
+			writel (cmd & ~CMD_ASE, &ehci->regs->command);
+			(void) handshake (&ehci->regs->status, STS_ASS, 0, 150);
+#if 0
+			// one VT8235 system wants to die with STS_FATAL
+			// unless this qh is leaked here. others seem ok...
+			qh = qh_get (qh);
+			dbg_qh ("async/off", ehci, qh);
+#endif
 		}
 		qh->qh_next.qh = ehci->async = 0;
 
@@ -986,13 +993,15 @@ static void start_unlink_async (struct ehci_hcd *ehci, struct ehci_qh *qh)
 
 /*-------------------------------------------------------------------------*/
 
-static unsigned long
-scan_async (struct ehci_hcd *ehci, unsigned long flags)
+static void
+scan_async (struct ehci_hcd *ehci)
 {
 	struct ehci_qh		*qh;
+	unsigned		count;
 
 rescan:
 	qh = ehci->async;
+	count = 0;
 	if (likely (qh != 0)) {
 		do {
 			/* clean any finished work for this qh */
@@ -1001,13 +1010,16 @@ scan_async (struct ehci_hcd *ehci, unsigned long flags)
 				qh = qh_get (qh);
 
 				/* concurrent unlink could happen here */
-				flags = qh_completions (ehci, qh, flags);
+				count += qh_completions (ehci, qh);
 				qh_put (ehci, qh);
 			}
 
 			/* unlink idle entries, reducing HC PCI usage as
 			 * well as HCD schedule-scanning costs.  removing
 			 * the last qh is deferred, since it's costly.
+			 *
+			 * FIXME don't unlink idle entries so quickly; it
+			 * can penalize (common) half duplex protocols.
 			 */
 			if (list_empty (&qh->qtd_list) && !ehci->reclaim) {
 				if (qh->qh_next.qh != qh) {
@@ -1020,10 +1032,18 @@ scan_async (struct ehci_hcd *ehci, unsigned long flags)
 						jiffies + EHCI_ASYNC_JIFFIES);
 				}
 			}
+
+			/* keep latencies down: let any irqs in */
+			if (count > max_completions) {
+				spin_unlock_irq (&ehci->lock);
+				cpu_relax ();
+				spin_lock_irq (&ehci->lock);
+				goto rescan;
+			}
+
 			qh = qh->qh_next.qh;
 			if (!qh)		/* unlinked? */
 				goto rescan;
 		} while (qh != ehci->async);
 	}
-	return flags;
 }

drivers/usb/host/ehci-sched.c

@@ -222,11 +222,10 @@ static int disable_periodic (struct ehci_hcd *ehci)
 
 // FIXME microframe periods not yet handled
 
-static unsigned long intr_deschedule (
+static void intr_deschedule (
 	struct ehci_hcd	*ehci,
 	struct ehci_qh	*qh,
-	int		wait,
-	unsigned long	flags
+	int		wait
 ) {
 	int		status;
 	unsigned	frame = qh->start;
@@ -256,10 +255,8 @@ static unsigned long intr_deschedule (
 	 */
 	if (((ehci_get_frame (&ehci->hcd) - frame) % qh->period) == 0) {
 		if (wait) {
-			spin_unlock_irqrestore (&ehci->lock, flags);
 			udelay (125);
 			qh->hw_next = EHCI_LIST_END;
-			spin_lock_irqsave (&ehci->lock, flags);
 		} else {
 			/* we may not be IDLE yet, but if the qh is empty
 			 * the race is very short.  then if qh also isn't
@@ -276,10 +273,9 @@ static unsigned long intr_deschedule (
 	hcd_to_bus (&ehci->hcd)->bandwidth_allocated -= 
 		(qh->usecs + qh->c_usecs) / qh->period;
 
-	vdbg ("descheduled qh %p, per = %d frame = %d count = %d, urbs = %d",
+	dbg ("descheduled qh %p, period = %d frame = %d count = %d, urbs = %d",
 		qh, qh->period, frame,
 		atomic_read (&qh->refcount), ehci->periodic_sched);
-	return flags;
 }
 
 static int check_period (
@@ -414,7 +410,7 @@ static int qh_schedule (struct ehci_hcd *ehci, struct ehci_qh *qh)
 
 	/* stuff into the periodic schedule */
 	qh->qh_state = QH_STATE_LINKED;
-	dbg ("qh %p usecs %d/%d period %d.0 starting %d.%d (gap %d)",
+	dbg ("scheduled qh %p usecs %d/%d period %d.0 starting %d.%d (gap %d)",
 		qh, qh->usecs, qh->c_usecs,
 		qh->period, frame, uframe, qh->gap_uf);
 	do {
@@ -495,29 +491,30 @@ static int intr_submit (
 	return status;
 }
 
-static unsigned long
+static unsigned
 intr_complete (
 	struct ehci_hcd	*ehci,
 	unsigned	frame,
-	struct ehci_qh	*qh,
-	unsigned long	flags		/* caller owns ehci->lock ... */
+	struct ehci_qh	*qh
 ) {
+	unsigned	count;
+
 	/* nothing to report? */
 	if (likely ((qh->hw_token & __constant_cpu_to_le32 (QTD_STS_ACTIVE))
 			!= 0))
-		return flags;
+		return 0;
 	if (unlikely (list_empty (&qh->qtd_list))) {
 		dbg ("intr qh %p no TDs?", qh);
-		return flags;
+		return 0;
 	}
 	
 	/* handle any completions */
-	flags = qh_completions (ehci, qh, flags);
+	count = qh_completions (ehci, qh);
 
 	if (unlikely (list_empty (&qh->qtd_list)))
-		flags = intr_deschedule (ehci, qh, 0, flags);
+		intr_deschedule (ehci, qh, 0);
 
-	return flags;
+	return count;
 }
 
 /*-------------------------------------------------------------------------*/
@@ -866,12 +863,11 @@ itd_schedule (struct ehci_hcd *ehci, struct urb *urb)
 
 #define	ISO_ERRS (EHCI_ISOC_BUF_ERR | EHCI_ISOC_BABBLE | EHCI_ISOC_XACTERR)
 
-static unsigned long
+static unsigned
 itd_complete (
 	struct ehci_hcd	*ehci,
 	struct ehci_itd	*itd,
-	unsigned	uframe,
-	unsigned long	flags
+	unsigned	uframe
 ) {
 	struct urb				*urb = itd->urb;
 	struct usb_iso_packet_descriptor	*desc;
@@ -909,7 +905,7 @@ itd_complete (
 
 	/* handle completion now? */
 	if ((itd->index + 1) != urb->number_of_packets)
-		return flags;
+		return 0;
 
 	/*
 	 * Always give the urb back to the driver ... expect it to submit
@@ -924,16 +920,17 @@ itd_complete (
 	if (urb->status == -EINPROGRESS)
 		urb->status = 0;
 
-	spin_unlock_irqrestore (&ehci->lock, flags);
+	/* complete() can reenter this HCD */
+	spin_unlock (&ehci->lock);
 	usb_hcd_giveback_urb (&ehci->hcd, urb);
-	spin_lock_irqsave (&ehci->lock, flags);
+	spin_lock (&ehci->lock);
 
 	/* defer stopping schedule; completion can submit */
 	ehci->periodic_sched--;
 	if (!ehci->periodic_sched)
 		(void) disable_periodic (ehci);
 
-	return flags;
+	return 1;
 }
 
 /*-------------------------------------------------------------------------*/
@@ -945,10 +942,6 @@ static int itd_submit (struct ehci_hcd *ehci, struct urb *urb, int mem_flags)
 
 	dbg ("itd_submit urb %p", urb);
 
-	/* NOTE DMA mapping assumes this ... */
-	if (urb->iso_frame_desc [0].offset != 0)
-		return -EINVAL;
-	
 	/* allocate ITDs w/o locking anything */
 	status = itd_urb_transaction (ehci, urb, mem_flags);
 	if (status < 0)
@@ -979,10 +972,11 @@ static int itd_submit (struct ehci_hcd *ehci, struct urb *urb, int mem_flags)
 
 /*-------------------------------------------------------------------------*/
 
-static unsigned long
-scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
+static void
+scan_periodic (struct ehci_hcd *ehci)
 {
 	unsigned	frame, clock, now_uframe, mod;
+	unsigned	count = 0;
 
 	mod = ehci->periodic_size << 3;
 
@@ -1005,6 +999,14 @@ scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
 		u32			type, *hw_p;
 		unsigned		uframes;
 
+		/* keep latencies down: let any irqs in */
+		if (count > max_completions) {
+			spin_unlock_irq (&ehci->lock);
+			cpu_relax ();
+			count = 0;
+			spin_lock_irq (&ehci->lock);
+		}
+
 restart:
 		/* scan schedule to _before_ current frame index */
 		if (frame == clock)
@@ -1028,8 +1030,8 @@ scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
 				last = (q.qh->hw_next == EHCI_LIST_END);
 				temp = q.qh->qh_next;
 				type = Q_NEXT_TYPE (q.qh->hw_next);
-				flags = intr_complete (ehci, frame,
-						qh_get (q.qh), flags);
+				count += intr_complete (ehci, frame,
+						qh_get (q.qh));
 				qh_put (ehci, q.qh);
 				q = temp;
 				break;
@@ -1061,8 +1063,8 @@ scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
 						type = Q_NEXT_TYPE (*hw_p);
 
 						/* might free q.itd ... */
-						flags = itd_complete (ehci,
-							temp.itd, uf, flags);
+						count += itd_complete (ehci,
+							temp.itd, uf);
 						break;
 					}
 				}
@@ -1078,7 +1080,7 @@ scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
 #ifdef have_split_iso
 			case Q_TYPE_SITD:
 				last = (q.sitd->hw_next == EHCI_LIST_END);
-				flags = sitd_complete (ehci, q.sitd, flags);
+				sitd_complete (ehci, q.sitd);
 				type = Q_NEXT_TYPE (q.sitd->hw_next);
 
 				// FIXME unlink SITD after split completes
@@ -1124,5 +1126,4 @@ scan_periodic (struct ehci_hcd *ehci, unsigned long flags)
 		} else
 			frame = (frame + 1) % ehci->periodic_size;
 	} 
-	return flags;
 }

drivers/usb/host/ehci.h

@@ -21,6 +21,23 @@
 
 /* definitions used for the EHCI driver */
 
+/* statistics can be kept for for tuning/monitoring */
+struct ehci_stats {
+	/* irq usage */
+	unsigned long		normal;
+	unsigned long		error;
+	unsigned long		reclaim;
+
+	/* termination of urbs from core */
+	unsigned long		complete;
+	unsigned long		unlink;
+
+	/* qhs patched to recover from td queueing race
+	 * (can avoid by using 'dummy td', allowing fewer irqs)
+	 */
+	unsigned long		qpatch;
+};
+
 /* ehci_hcd->lock guards shared data against other CPUs:
  *   ehci_hcd:	async, reclaim, periodic (and shadow), ...
  *   hcd_dev:	ep[]
@@ -72,6 +89,13 @@ struct ehci_hcd {			/* one per controller */
 	struct pci_pool		*sitd_pool;	/* sitd per split iso urb */
 
 	struct timer_list	watchdog;
+
+#ifdef EHCI_STATS
+	struct ehci_stats	stats;
+#	define COUNT(x) do { (x)++; } while (0)
+#else
+#	define COUNT(x) do {} while (0)
+#endif
 };
 
 /* unwrap an HCD pointer to get an EHCI_HCD pointer */ 
@@ -400,10 +424,22 @@ struct ehci_fstn {
 #define SUBMIT_URB(urb,mem_flags) usb_submit_urb(urb)
 #define STUB_DEBUG_FILES
 
+static inline int hcd_register_root (struct usb_hcd *hcd)
+{
+	return usb_new_device (hcd_to_bus (hcd)->root_hub);
+}
+
 #else	/* LINUX_VERSION_CODE */
 
+// hcd_to_bus() eventually moves to hcd.h on 2.5 too
 static inline struct usb_bus *hcd_to_bus (struct usb_hcd *hcd)
 	{ return &hcd->self; }
+// ... as does hcd_register_root()
+static inline int hcd_register_root (struct usb_hcd *hcd)
+{
+	return usb_register_root_hub (
+		hcd_to_bus (hcd)->root_hub, &hcd->pdev->dev);
+}
 
 #define SUBMIT_URB(urb,mem_flags) usb_submit_urb(urb,mem_flags)
 

drivers/usb/host/ohci-hcd.c

@@ -92,6 +92,7 @@
 #endif
 
 #include <linux/usb.h>
+#include <linux/version.h>
 #include "../core/hcd.h"
 
 #include <asm/io.h>
@@ -108,7 +109,7 @@
  *	- lots more testing!!
  */
 
-#define DRIVER_VERSION "2002-Sep-03"
+#define DRIVER_VERSION "2002-Sep-17"
 #define DRIVER_AUTHOR "Roman Weissgaerber, David Brownell"
 #define DRIVER_DESC "USB 1.1 'Open' Host Controller (OHCI) Driver"
 
@@ -318,9 +319,6 @@ ohci_free_config (struct usb_hcd *hcd, struct usb_device *udev)
 	struct hcd_dev		*dev = (struct hcd_dev *) udev->hcpriv;
 	int			i;
 	unsigned long		flags;
-#ifdef DEBUG
-	int			rescans = 0;
-#endif
 
 rescan:
 	/* free any eds, and dummy tds, still hanging around */
@@ -340,16 +338,18 @@ ohci_free_config (struct usb_hcd *hcd, struct usb_device *udev)
 			td_free (ohci, ed->dummy);
 			break;
 		default:
-#ifdef DEBUG
-			err ("illegal ED %d state in free_config, %d",
+			err ("%s-%s ed %p (#%d) not unlinked; disconnect() bug? %d",
+				ohci->hcd.self.bus_name, udev->devpath, ed,
 				i, ed->state);
-#endif
 			/* ED_OPER: some driver disconnect() is broken,
 			 * it didn't even start its unlinks much less wait
 			 * for their completions.
 			 * OTHERWISE:  hcd bug, ed is garbage
+			 *
+			 * ... we can't recycle this memory in either case,
+			 * so just leak it to avoid oopsing.
 			 */
-			BUG ();
+			continue;
 		}
 		ed_free (ohci, ed);
 	}
@@ -360,13 +360,9 @@ ohci_free_config (struct usb_hcd *hcd, struct usb_device *udev)
 #ifdef DEBUG
 	/* a driver->disconnect() returned before its unlinks completed? */
 	if (in_interrupt ()) {
-		dbg ("WARNING: spin in interrupt; driver->disconnect() bug");
-		dbg ("dev usb-%s-%s ep 0x%x", 
+		warn ("disconnect() bug for dev usb-%s-%s ep 0x%x", 
 			ohci->hcd.self.bus_name, udev->devpath, i);
 	}
-	BUG_ON (!(readl (&ohci->regs->intrenable) & OHCI_INTR_SF));
-	BUG_ON (rescans >= 2);	/* HWBUG */
-	rescans++;
 #endif
 
 	spin_unlock_irqrestore (&ohci->lock, flags);

drivers/usb/host/ohci-q.c

@@ -36,12 +36,7 @@ static void finish_urb (struct ohci_hcd *ohci, struct urb *urb)
 {
 	unsigned long	flags;
 
-#ifdef DEBUG
-	if (!urb->hcpriv) {
-		err ("already unlinked!");
-		BUG ();
-	}
-#endif
+	// ASSERT (urb->hcpriv != 0);
 
 	urb_free_priv (ohci, urb->hcpriv);
 	urb->hcpriv = NULL;
@@ -51,6 +46,7 @@ static void finish_urb (struct ohci_hcd *ohci, struct urb *urb)
 		urb->status = 0;
 	spin_unlock_irqrestore (&urb->lock, flags);
 
+	// what lock protects these?
 	switch (usb_pipetype (urb->pipe)) {
 	case PIPE_ISOCHRONOUS:
 		ohci->hcd.self.bandwidth_isoc_reqs--;
@@ -425,6 +421,9 @@ static struct ed *ed_get (
 	/* FIXME:  Don't do this without knowing it's safe to clobber this
 	 * state/mode info.  Currently the upper layers don't support such
 	 * guarantees; we're lucky changing config/altsetting is rare.
+	 * The state/mode info also changes during enumeration: set_address
+	 * uses the 'wrong' device address, and ep0 maxpacketsize will often
+	 * improve on the initial value.
 	 */
   	if (ed->state == ED_IDLE) {
 		u32	info;
@@ -454,25 +453,6 @@ static struct ed *ed_get (
 		}
 		ed->hwINFO = info;
 
-#ifdef DEBUG
-	/*
-	 * There are two other cases we ought to change hwINFO, both during
-	 * enumeration.  There, the control request completes, unlinks, and
-	 * the next request gets queued before the unlink completes, so it
-	 * uses old/wrong hwINFO.  How much of a problem is this?  khubd is
-	 * already retrying after such failures...
-	 */
-	} else if (type == PIPE_CONTROL) {
-		u32	info = le32_to_cpup (&ed->hwINFO);
-
-		if (!(info & 0x7f))
-			dbg ("RETRY ctrl: address != 0");
-		info >>= 16;
-		if (info != udev->epmaxpacketin [0])
-			dbg ("RETRY ctrl: maxpacket %d != 8",
-				udev->epmaxpacketin [0]);
-
-#endif /* DEBUG */
 	}
 
 done:
@@ -526,10 +506,7 @@ td_fill (unsigned int info,
 	struct urb_priv		*urb_priv = urb->hcpriv;
 	int			is_iso = info & TD_ISO;
 
-	if (index >= urb_priv->length) {
-		err ("internal OHCI error: TD index > length");
-		return;
-	}
+	// ASSERT (index < urb_priv->length);
 
 	/* aim for only one interrupt per urb.  mostly applies to control
 	 * and iso; other urbs rarely need more than one TD per urb.
@@ -578,6 +555,7 @@ td_fill (unsigned int info,
 	wmb ();
 
 	/* append to queue */
+	list_add_tail (&td->td_list, &td->ed->td_list);
 	td->ed->hwTailP = td->hwNextTD;
 }
 
@@ -698,8 +676,7 @@ static void td_submit_urb (
 		ohci->hcd.self.bandwidth_isoc_reqs++;
 		break;
 	}
-	if (urb_priv->length != cnt)
-		dbg ("TD LENGTH %d != CNT %d", urb_priv->length, cnt);
+	// ASSERT (urb_priv->length == cnt);
 }
 
 /*-------------------------------------------------------------------------*
@@ -714,6 +691,8 @@ static void td_done (struct urb *urb, struct td *td)
 	u32	tdINFO = le32_to_cpup (&td->hwINFO);
 	int	cc = 0;
 
+	list_del (&td->td_list);
+
 	/* ISO ... drivers see per-TD length/status */
   	if (tdINFO & TD_ISO) {
  		u16	tdPSW = le16_to_cpu (td->hwPSW [0]);
@@ -792,74 +771,106 @@ static void td_done (struct urb *urb, struct td *td)
 
 /*-------------------------------------------------------------------------*/
 
+static inline struct td *
+ed_halted (struct ohci_hcd *ohci, struct td *td, int cc, struct td *rev)
+{
+  	struct urb		*urb = td->urb;
+	struct ed		*ed = td->ed;
+	struct list_head	*tmp = td->td_list.next;
+	u32			toggle = ed->hwHeadP & ED_C;
+
+	/* clear ed halt; this is the td that caused it, but keep it inactive
+	 * until its urb->complete() has a chance to clean up.
+	 */
+	ed->hwINFO |= ED_SKIP;
+	wmb ();
+	td->ed->hwHeadP &= ~ED_H; 
+
+	while (tmp != &ed->td_list) {
+		struct td	*next;
+
+		next = list_entry (tmp, struct td, td_list);
+		tmp = next->td_list.next;
+
+		/* move other tds from this urb to the donelist, after 'td'.
+		 * order won't matter here: no errors, nothing transferred.
+		 *
+		 * NOTE: this "knows" short control reads won't need fixup:
+		 * hc went from the (one) data TD to the status td. that'll
+		 * change if multi-td control DATA segments are supported,
+		 * and we want to send the status packet.
+		 */
+		if (next->urb == urb) {
+			u32	info = next->hwINFO;
+
+			info |= cpu_to_le32 (TD_DONE);
+			info &= ~cpu_to_le32 (TD_CC);
+			next->hwINFO = info;
+			next->next_dl_td = rev;	
+			rev = next;
+			continue;
+		}
+
+		/* restart ed with first td of this next urb */
+		ed->hwHeadP = cpu_to_le32 (next->td_dma) | toggle;
+		tmp = 0;
+		break;
+	}
+
+	/* no urbs queued? then ED is empty. */
+	if (tmp)
+		ed->hwHeadP = cpu_to_le32 (ed->dummy->td_dma) | toggle;
+
+	/* help for troubleshooting: */
+	dbg ("urb %p usb-%s-%s ep-%d-%s cc %d --> status %d",
+		urb,
+		urb->dev->bus->bus_name, urb->dev->devpath,
+		usb_pipeendpoint (urb->pipe),
+		usb_pipein (urb->pipe) ? "IN" : "OUT",
+		cc, cc_to_error [cc]);
+
+	return rev;
+}
+
 /* replies to the request have to be on a FIFO basis so
  * we unreverse the hc-reversed done-list
  */
 static struct td *dl_reverse_done_list (struct ohci_hcd *ohci)
 {
-	__u32		td_list_hc;
+	u32		td_dma;
 	struct td	*td_rev = NULL;
-	struct td	*td_list = NULL;
-  	urb_priv_t	*urb_priv = NULL;
+	struct td	*td = NULL;
   	unsigned long	flags;
 
   	spin_lock_irqsave (&ohci->lock, flags);
 
-	td_list_hc = le32_to_cpup (&ohci->hcca->done_head);
+	td_dma = le32_to_cpup (&ohci->hcca->done_head);
 	ohci->hcca->done_head = 0;
 
-	while (td_list_hc) {		
+	/* get TD from hc's singly linked list, and
+	 * prepend to ours.  ed->td_list changes later.
+	 */
+	while (td_dma) {		
 	    	int		cc;
 
-		td_list = dma_to_td (ohci, td_list_hc);
-
-		td_list->hwINFO |= cpu_to_le32 (TD_DONE);
-
-		cc = TD_CC_GET (le32_to_cpup (&td_list->hwINFO));
-		if (cc != TD_CC_NOERROR) {
-			urb_priv = (urb_priv_t *) td_list->urb->hcpriv;
-
-			/* Non-iso endpoints can halt on error; un-halt,
-			 * and dequeue any other TDs from this urb.
-			 * No other TD could have caused the halt.
-			 */
-			if (td_list->ed->hwHeadP & ED_H) {
-				if (urb_priv && ((td_list->index + 1)
-						< urb_priv->length)) {
-#ifdef DEBUG
-					struct urb *urb = td_list->urb;
-
-					/* help for troubleshooting: */
-					dbg ("urb %p usb-%s-%s ep-%d-%s "
-						    "(td %d/%d), "
-						    "cc %d --> status %d",
-						td_list->urb,
-						urb->dev->bus->bus_name,
-						urb->dev->devpath,
-						usb_pipeendpoint (urb->pipe),
-						usb_pipein (urb->pipe)
-						    ? "IN" : "OUT",
-						1 + td_list->index,
-						urb_priv->length,
-						cc, cc_to_error [cc]);
-#endif
-					td_list->ed->hwHeadP = 
-			    (urb_priv->td [urb_priv->length - 1]->hwNextTD
-				    & __constant_cpu_to_le32 (TD_MASK))
-			    | (td_list->ed->hwHeadP & ED_C);
-					urb_priv->td_cnt += urb_priv->length
-						- td_list->index - 1;
-				} else 
-					td_list->ed->hwHeadP &= ~ED_H;
-			}
-		}
+		td = dma_to_td (ohci, td_dma);
 
-		td_list->next_dl_td = td_rev;	
-		td_rev = td_list;
-		td_list_hc = le32_to_cpup (&td_list->hwNextTD);
+		td->hwINFO |= cpu_to_le32 (TD_DONE);
+		cc = TD_CC_GET (le32_to_cpup (&td->hwINFO));
+
+		/* Non-iso endpoints can halt on error; un-halt,
+		 * and dequeue any other TDs from this urb.
+		 * No other TD could have caused the halt.
+		 */
+		if (cc != TD_CC_NOERROR && (td->ed->hwHeadP & ED_H))
+			td_rev = ed_halted (ohci, td, cc, td_rev);
+
+		td->next_dl_td = td_rev;	
+		td_rev = td;
+		td_dma = le32_to_cpup (&td->hwNextTD);
 	}	
 	spin_unlock_irqrestore (&ohci->lock, flags);
-	return td_list;
+	return td_rev;
 }
 
 /*-------------------------------------------------------------------------*/
@@ -874,9 +885,9 @@ static void finish_unlinks (struct ohci_hcd *ohci, u16 tick)
 
 rescan_all:
 	for (last = &ohci->ed_rm_list, ed = *last; ed != NULL; ed = *last) {
-		struct td	*td, *td_next, *tdHeadP, *tdTailP;
-		u32		*td_p;
-		int		completed, modified;
+		struct list_head	*entry, *tmp;
+		int			completed, modified;
+		u32			*prev;
 
 		/* only take off EDs that the HC isn't using, accounting for
 		 * frame counter wraps.
@@ -897,53 +908,52 @@ static void finish_unlinks (struct ohci_hcd *ohci, u16 tick)
 		/* unlink urbs as requested, but rescan the list after
 		 * we call a completion since it might have unlinked
 		 * another (earlier) urb
-		 *
-		 * FIXME use td_list to scan, not td hashtables.
 		 */
 rescan_this:
 		completed = 0;
+		prev = &ed->hwHeadP;
+		list_for_each_safe (entry, tmp, &ed->td_list) {
+			struct td	*td;
+			struct urb	*urb;
+			urb_priv_t	*urb_priv;
+			u32		savebits;
+
+			td = list_entry (entry, struct td, td_list);
+			urb = td->urb;
+			urb_priv = td->urb->hcpriv;
+
+			if (urb_priv->state != URB_DEL) {
+				prev = &td->hwNextTD;
+				continue;
+			}
+
+			/* patch pointer hc uses */
+			savebits = *prev & cpu_to_le32 (TD_MASK);
+			*prev = td->hwNextTD | savebits;
+
+			/* HC may have partly processed this TD */
+			td_done (urb, td);
+			urb_priv->td_cnt++;
 
-		tdTailP = dma_to_td (ohci, le32_to_cpup (&ed->hwTailP));
-		tdHeadP = dma_to_td (ohci, le32_to_cpup (&ed->hwHeadP));
-		td_p = &ed->hwHeadP;
-
-		for (td = tdHeadP; td != tdTailP; td = td_next) {
-			struct urb *urb = td->urb;
-			urb_priv_t *urb_priv = td->urb->hcpriv;
-
-			td_next = dma_to_td (ohci,
-				le32_to_cpup (&td->hwNextTD));
-			if (urb_priv->state == URB_DEL) {
-
-				/* HC may have partly processed this TD */
-				td_done (urb, td);
-				urb_priv->td_cnt++;
-
-				*td_p = td->hwNextTD | (*td_p & ~TD_MASK);
-
-				/* URB is done; clean up */
-				if (urb_priv->td_cnt == urb_priv->length) {
-					modified = completed = 1;
-     					spin_unlock (&ohci->lock);
-					finish_urb (ohci, urb);
-					spin_lock (&ohci->lock);
-				}
-			} else {
-				td_p = &td->hwNextTD;
+			/* if URB is done, clean up */
+			if (urb_priv->td_cnt == urb_priv->length) {
+				modified = completed = 1;
+				spin_unlock (&ohci->lock);
+				finish_urb (ohci, urb);
+				spin_lock (&ohci->lock);
 			}
 		}
+		if (completed && !list_empty (&ed->td_list))
+			goto rescan_this;
 
 		/* ED's now officially unlinked, hc doesn't see */
 		ed->state = ED_IDLE;
-		ed->hwINFO &= ~ED_SKIP;
+		ed->hwINFO &= ~(ED_SKIP | ED_DEQUEUE);
 		ed->hwHeadP &= ~ED_H;
 		ed->hwNextED = 0;
 
 		/* but if there's work queued, reschedule */
-		tdHeadP = dma_to_td (ohci, le32_to_cpup (&ed->hwHeadP));
-		if (tdHeadP != tdTailP) {
-			if (completed)
-				goto rescan_this;
+		if (!list_empty (&ed->td_list)) {
 			if (!ohci->disabled && !ohci->sleeping)
 				ed_schedule (ohci, ed);
 		}
@@ -1027,10 +1037,15 @@ static void dl_done_list (struct ohci_hcd *ohci, struct td *td)
   		}
 
 		/* clean schedule:  unlink EDs that are no longer busy */
-		if ((ed->hwHeadP & __constant_cpu_to_le32 (TD_MASK))
-					== ed->hwTailP
-				&& (ed->state == ED_OPER)) 
+		if (list_empty (&ed->td_list))
 			ed_deschedule (ohci, ed);
+		/* ... reenabling halted EDs only after fault cleanup */
+		else if (!(ed->hwINFO & ED_DEQUEUE)) {
+			td = list_entry (ed->td_list.next, struct td, td_list);
+			if (!(td->hwINFO & TD_DONE))
+				ed->hwINFO &= ~ED_SKIP;
+		}
+
     		td = td_next;
   	}  
 	spin_unlock_irqrestore (&ohci->lock, flags);

drivers/usb/misc/Config.help

@@ -112,3 +112,13 @@ CONFIG_USB_SPEEDTCH
   For more information, see Johan Verrept's webpages at
   <http://linux-usb.sourceforge.net/SpeedTouch/>.
 
+CONFIG_USB_LCD
+  Say Y here if you want to connect an USBLCD to your computer's
+  USB port. The USBLCD is a small USB interface board for
+  alphanumeric LCD modules. See <http://www.usblcd.de> for more
+  information.
+
+  This code is also available as a module ( = code which can be
+  inserted in and removed from the running kernel whenever you want).
+  The module will be called usblcd.o. If you want to compile it as
+  a module, say M here and read <file:Documentation/modules.txt>.

drivers/usb/misc/usblcd.c

 /***************************************************************************** 
  *                          USBLCD Kernel Driver                             *
  *        See http://www.usblcd.de for Hardware and Documentation.           *
- *                            Version 1.01                                   *
+ *                            Version 1.03                                   *
  *             (C) 2002 Adams IT Services <info@usblcd.de>                   *
  *                                                                           *
  *     This file is licensed under the GPL. See COPYING in the package.      *
@@ -18,7 +18,7 @@
 #include <asm/uaccess.h>
 #include <linux/usb.h>
 
-#define DRIVER_VERSION "USBLCD Driver Version 1.01"
+#define DRIVER_VERSION "USBLCD Driver Version 1.03"
 
 #define USBLCD_MINOR		144
 
@@ -26,7 +26,7 @@
 #define IOCTL_GET_DRV_VERSION	2
 
 /* stall/wait timeout for USBLCD */
-#define NAK_TIMEOUT	(HZ)
+#define NAK_TIMEOUT	(10*HZ)
 
 #define IBUF_SIZE	0x1000
 #define OBUF_SIZE	0x10000
@@ -318,7 +318,7 @@ static void disconnect_lcd(struct usb_interface *intf)
 }
 
 static struct usb_device_id id_table [] = {
-	{ .idVendor = 0x1212, .match_flags = USB_DEVICE_ID_MATCH_VENDOR, },
+	{ .idVendor = 0x10D2, .match_flags = USB_DEVICE_ID_MATCH_VENDOR, },
 	{},
 };
 

drivers/usb/serial/usb-serial.h

@@ -232,6 +232,7 @@ struct usb_serial_device_type {
 
 extern int  usb_serial_register(struct usb_serial_device_type *new_device);
 extern void usb_serial_deregister(struct usb_serial_device_type *device);
+extern void usb_serial_port_softint(void *private);
 
 extern int usb_serial_probe(struct usb_interface *iface, const struct usb_device_id *id);
 extern void usb_serial_disconnect(struct usb_interface *iface);

drivers/usb/serial/usbserial.c

@@ -498,7 +498,7 @@ int ezusb_writememory (struct usb_serial *serial, int address, unsigned char *da
 		return -ENOMEM;
 	}
 	memcpy (transfer_buffer, data, length);
-	result = usb_control_msg (serial->dev, usb_sndctrlpipe(serial->dev, 0), bRequest, 0x40, address, 0, transfer_buffer, length, 300);
+	result = usb_control_msg (serial->dev, usb_sndctrlpipe(serial->dev, 0), bRequest, 0x40, address, 0, transfer_buffer, length, 3*HZ);
 	kfree (transfer_buffer);
 	return result;
 }
@@ -557,12 +557,11 @@ static int serial_open (struct tty_struct *tty, struct file * filp)
 			retval = serial->type->open(port, filp);
 		else
 			retval = generic_open(port, filp);
-	}
-
-	if (retval) {
-		port->open_count = 0;
-		if (serial->type->owner)
-			__MOD_DEC_USE_COUNT(serial->type->owner);
+		if (retval) {
+			port->open_count = 0;
+			if (serial->type->owner)
+				__MOD_DEC_USE_COUNT(serial->type->owner);
+		}
 	}
 
 	up (&port->sem);
@@ -1091,6 +1090,8 @@ static void generic_write_bulk_callback (struct urb *urb)
 		return;
 	}
 
+	usb_serial_port_softint((void *)port);
+
 	queue_task(&port->tqueue, &tq_immediate);
 	mark_bh(IMMEDIATE_BH);
 
@@ -1109,14 +1110,18 @@ static void generic_shutdown (struct usb_serial *serial)
 	}
 }
 
-static void port_softint(void *private)
+void usb_serial_port_softint(void *private)
 {
 	struct usb_serial_port *port = (struct usb_serial_port *)private;
-	struct usb_serial *serial = get_usb_serial (port, __FUNCTION__);
+	struct usb_serial *serial;
 	struct tty_struct *tty;
 
 	dbg("%s - port %d", __FUNCTION__, port->number);
 	
+	if (!port)
+		return;
+
+	serial = get_usb_serial (port, __FUNCTION__);
 	if (!serial)
 		return;
 
@@ -1400,7 +1405,7 @@ int usb_serial_probe(struct usb_interface *interface,
 		port->number = i + serial->minor;
 		port->serial = serial;
 		port->magic = USB_SERIAL_PORT_MAGIC;
-		port->tqueue.routine = port_softint;
+		port->tqueue.routine = usb_serial_port_softint;
 		port->tqueue.data = port;
 		init_MUTEX (&port->sem);
 	}
@@ -1690,6 +1695,7 @@ EXPORT_SYMBOL(usb_serial_register);
 EXPORT_SYMBOL(usb_serial_deregister);
 EXPORT_SYMBOL(usb_serial_probe);
 EXPORT_SYMBOL(usb_serial_disconnect);
+EXPORT_SYMBOL(usb_serial_port_softint);
 #ifdef USES_EZUSB_FUNCTIONS
 	EXPORT_SYMBOL(ezusb_writememory);
 	EXPORT_SYMBOL(ezusb_set_reset);

drivers/usb/serial/whiteheat.c

 /*
  * USB ConnectTech WhiteHEAT driver
  *
+ *	Copyright (C) 2002
+ *	    Connect Tech Inc.
+ *
  *	Copyright (C) 1999 - 2001
  *	    Greg Kroah-Hartman (greg@kroah.com)
  *
@@ -11,6 +14,9 @@
  *
  * See Documentation/usb/usb-serial.txt for more information on using this driver
  *
+ * (10/09/2002) Stuart MacDonald (stuartm@connecttech.com)
+ *	Upgrade to full working driver
+ *
  * (05/30/2001) gkh
  *	switched from using spinlock to a semaphore, which fixes lots of problems.
  *
@@ -71,6 +77,8 @@
 #include <linux/spinlock.h>
 #include <asm/uaccess.h>
 #include <linux/usb.h>
+#include <linux/serial_reg.h>
+#include <linux/serial.h>
 
 #ifdef CONFIG_USB_SERIAL_DEBUG
 	static int debug = 1;
@@ -85,8 +93,8 @@
 /*
  * Version Information
  */
-#define DRIVER_VERSION "v1.2"
-#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>"
+#define DRIVER_VERSION "v2.0"
+#define DRIVER_AUTHOR "Greg Kroah-Hartman <greg@kroah.com>, Stuart MacDonald <stuartm@connecttech.com>"
 #define DRIVER_DESC "USB ConnectTech WhiteHEAT driver"
 
 #define CONNECT_TECH_VENDOR_ID		0x0710
@@ -125,16 +133,25 @@ static struct usb_driver whiteheat_driver = {
 	.id_table =	id_table_combined,
 };
 
+/* function prototypes for the Connect Tech WhiteHEAT prerenumeration device */
+static int  whiteheat_firmware_download	(struct usb_serial *serial);
+static int  whiteheat_firmware_attach	(struct usb_serial *serial);
+
 /* function prototypes for the Connect Tech WhiteHEAT serial converter */
+static int  whiteheat_attach		(struct usb_serial *serial);
+static void whiteheat_shutdown		(struct usb_serial *serial);
 static int  whiteheat_open		(struct usb_serial_port *port, struct file *filp);
 static void whiteheat_close		(struct usb_serial_port *port, struct file *filp);
+static int  whiteheat_write		(struct usb_serial_port *port, int from_user, const unsigned char *buf, int count);
+static int  whiteheat_write_room	(struct usb_serial_port *port);
 static int  whiteheat_ioctl		(struct usb_serial_port *port, struct file * file, unsigned int cmd, unsigned long arg);
 static void whiteheat_set_termios	(struct usb_serial_port *port, struct termios * old);
+static void whiteheat_break_ctl		(struct usb_serial_port *port, int break_state);
+static int  whiteheat_chars_in_buffer	(struct usb_serial_port *port);
 static void whiteheat_throttle		(struct usb_serial_port *port);
 static void whiteheat_unthrottle	(struct usb_serial_port *port);
-static int  whiteheat_firmware_download	(struct usb_serial *serial);
-static int  whiteheat_attach		(struct usb_serial *serial);
-static void whiteheat_shutdown		(struct usb_serial *serial);
+static void whiteheat_read_callback	(struct urb *urb);
+static void whiteheat_write_callback	(struct urb *urb);
 
 static struct usb_serial_device_type whiteheat_fake_device = {
 	.owner =		THIS_MODULE,
@@ -145,6 +162,7 @@ static struct usb_serial_device_type whiteheat_fake_device = {
 	.num_bulk_out =		NUM_DONT_CARE,
 	.num_ports =		1,
 	.probe =		whiteheat_firmware_download,
+	.attach =		whiteheat_firmware_attach,
 };
 
 static struct usb_serial_device_type whiteheat_device = {
@@ -155,201 +173,311 @@ static struct usb_serial_device_type whiteheat_device = {
 	.num_bulk_in =		NUM_DONT_CARE,
 	.num_bulk_out =		NUM_DONT_CARE,
 	.num_ports =		4,
+	.attach =		whiteheat_attach,
+	.shutdown =		whiteheat_shutdown,
 	.open =			whiteheat_open,
 	.close =		whiteheat_close,
-	.throttle =		whiteheat_throttle,
-	.unthrottle =		whiteheat_unthrottle,
+	.write =		whiteheat_write,
+	.write_room =		whiteheat_write_room,
 	.ioctl =		whiteheat_ioctl,
 	.set_termios =		whiteheat_set_termios,
-	.attach =		whiteheat_attach,
-	.shutdown =		whiteheat_shutdown,
+	.break_ctl =		whiteheat_break_ctl,
+	.chars_in_buffer =	whiteheat_chars_in_buffer,
+	.throttle =		whiteheat_throttle,
+	.unthrottle =		whiteheat_unthrottle,
+	.read_bulk_callback =	whiteheat_read_callback,
+	.write_bulk_callback =	whiteheat_write_callback,
 };
 
-struct whiteheat_private {
+
+struct whiteheat_command_private {
+	spinlock_t		lock;
+	__u8			port_running;
 	__u8			command_finished;
 	wait_queue_head_t	wait_command;	/* for handling sleeping while waiting for a command to finish */
+	__u8			result_buffer[64];
 };
 
 
-/* local function prototypes */
-static inline void set_rts	(struct usb_serial_port *port, unsigned char rts);
-static inline void set_dtr	(struct usb_serial_port *port, unsigned char dtr);
-static inline void set_break	(struct usb_serial_port *port, unsigned char brk);
+#define THROTTLED		0x01
+#define ACTUALLY_THROTTLED	0x02
+
+struct whiteheat_private {
+	spinlock_t		lock;
+	__u8			flags;
+	__u8			mcr;
+};
+
 
+/* local function prototypes */
+static int start_command_port(struct usb_serial *serial);
+static void stop_command_port(struct usb_serial *serial);
+static void command_port_write_callback(struct urb *urb);
+static void command_port_read_callback(struct urb *urb);
+
+static int firm_send_command(struct usb_serial_port *port, __u8 command, __u8 *data, __u8 datasize);
+static int firm_open(struct usb_serial_port *port);
+static int firm_close(struct usb_serial_port *port);
+static int firm_setup_port(struct usb_serial_port *port);
+static int firm_set_rts(struct usb_serial_port *port, __u8 onoff);
+static int firm_set_dtr(struct usb_serial_port *port, __u8 onoff);
+static int firm_set_break(struct usb_serial_port *port, __u8 onoff);
+static int firm_purge(struct usb_serial_port *port, __u8 rxtx);
+static int firm_get_dtr_rts(struct usb_serial_port *port);
+static int firm_report_tx_done(struct usb_serial_port *port);
 
 
 #define COMMAND_PORT		4
 #define COMMAND_TIMEOUT		(2*HZ)	/* 2 second timeout for a command */
+#define CLOSING_DELAY		(30 * HZ)
+
 
 /*****************************************************************************
- * Connect Tech's White Heat specific driver functions
+ * Connect Tech's White Heat prerenumeration driver functions
  *****************************************************************************/
-static void command_port_write_callback (struct urb *urb)
+
+/* steps to download the firmware to the WhiteHEAT device:
+ - hold the reset (by writing to the reset bit of the CPUCS register)
+ - download the VEND_AX.HEX file to the chip using VENDOR_REQUEST-ANCHOR_LOAD
+ - release the reset (by writing to the CPUCS register)
+ - download the WH.HEX file for all addresses greater than 0x1b3f using
+   VENDOR_REQUEST-ANCHOR_EXTERNAL_RAM_LOAD
+ - hold the reset
+ - download the WH.HEX file for all addresses less than 0x1b40 using
+   VENDOR_REQUEST_ANCHOR_LOAD
+ - release the reset
+ - device renumerated itself and comes up as new device id with all
+   firmware download completed.
+*/
+static int whiteheat_firmware_download (struct usb_serial *serial)
 {
+	int response;
+	const struct whiteheat_hex_record *record;
+	
 	dbg("%s", __FUNCTION__);
+	
+	response = ezusb_set_reset (serial, 1);
 
-	if (urb->status) {
-		dbg ("nonzero urb status: %d", urb->status);
-		return;
+	record = &whiteheat_loader[0];
+	while (record->address != 0xffff) {
+		response = ezusb_writememory (serial, record->address, 
+				(unsigned char *)record->data, record->data_size, 0xa0);
+		if (response < 0) {
+			err("%s - ezusb_writememory failed for loader (%d %04X %p %d)",
+				__FUNCTION__, response, record->address, record->data, record->data_size);
+			break;
+		}
+		++record;
 	}
 
-	usb_serial_debug_data (__FILE__, __FUNCTION__, urb->actual_length, urb->transfer_buffer);
+	response = ezusb_set_reset (serial, 0);
 
-	return;
+	record = &whiteheat_firmware[0];
+	while (record->address < 0x1b40) {
+		++record;
+	}
+	while (record->address != 0xffff) {
+		response = ezusb_writememory (serial, record->address, 
+				(unsigned char *)record->data, record->data_size, 0xa3);
+		if (response < 0) {
+			err("%s - ezusb_writememory failed for first firmware step (%d %04X %p %d)", 
+				__FUNCTION__, response, record->address, record->data, record->data_size);
+			break;
+		}
+		++record;
+	}
+	
+	response = ezusb_set_reset (serial, 1);
+
+	record = &whiteheat_firmware[0];
+	while (record->address < 0x1b40) {
+		response = ezusb_writememory (serial, record->address, 
+				(unsigned char *)record->data, record->data_size, 0xa0);
+		if (response < 0) {
+			err("%s - ezusb_writememory failed for second firmware step (%d %04X %p %d)", 
+				__FUNCTION__, response, record->address, record->data, record->data_size);
+			break;
+		}
+		++record;
+	}
+
+	response = ezusb_set_reset (serial, 0);
+
+	return 0;
 }
 
 
-static void command_port_read_callback (struct urb *urb)
+static int whiteheat_firmware_attach (struct usb_serial *serial)
 {
-	struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
-	struct usb_serial *serial = get_usb_serial (port, __FUNCTION__);
+	/* We want this device to fail to have a driver assigned to it */
+	return 1;
+}
+
+
+/*****************************************************************************
+ * Connect Tech's White Heat serial driver functions
+ *****************************************************************************/
+static int whiteheat_attach (struct usb_serial *serial)
+{
+	struct usb_serial_port *command_port;
+	struct whiteheat_command_private *command_info;
+	struct usb_serial_port *port;
 	struct whiteheat_private *info;
-	unsigned char *data = urb->transfer_buffer;
-	int result;
+	struct whiteheat_hw_info *hw_info;
+	int pipe;
+	int ret;
+	int alen;
+	__u8 command[2] = { WHITEHEAT_GET_HW_INFO, 0 };
+	__u8 result[sizeof(*hw_info) + 1];
+	int i;
 
-	dbg("%s", __FUNCTION__);
+	command_port = &serial->port[COMMAND_PORT];
 
-	if (urb->status) {
-		dbg("%s - nonzero urb status: %d", __FUNCTION__, urb->status);
-		return;
+	pipe = usb_sndbulkpipe (serial->dev, command_port->bulk_out_endpointAddress);
+	ret = usb_bulk_msg (serial->dev, pipe, command, sizeof(command), &alen, COMMAND_TIMEOUT);
+	if (ret) {
+		err("%s: Couldn't send command [%d]", serial->type->name, ret);
+		goto no_firmware;
+	} else if (alen != sizeof(command)) {
+		err("%s: Send command incomplete [%d]", serial->type->name, alen);
+		goto no_firmware;
 	}
 
-	if (!serial) {
-		dbg("%s - bad serial pointer, exiting", __FUNCTION__);
-		return;
+	pipe = usb_rcvbulkpipe (serial->dev, command_port->bulk_in_endpointAddress);
+	ret = usb_bulk_msg (serial->dev, pipe, result, sizeof(result), &alen, COMMAND_TIMEOUT);
+	if (ret) {
+		err("%s: Couldn't get results [%d]", serial->type->name, ret);
+		goto no_firmware;
+	} else if (alen != sizeof(result)) {
+		err("%s: Get results incomplete [%d]", serial->type->name, alen);
+		goto no_firmware;
+	} else if (result[0] != command[0]) {
+		err("%s: Command failed [%d]", serial->type->name, result[0]);
+		goto no_firmware;
 	}
-	
-	usb_serial_debug_data (__FILE__, __FUNCTION__, urb->actual_length, data);
 
-	info = (struct whiteheat_private *)port->private;
-	if (!info) {
-		dbg("%s - info is NULL, exiting.", __FUNCTION__);
-		return;
-	}
+	hw_info = (struct whiteheat_hw_info *)&result[1];
 
-	/* right now, if the command is COMMAND_COMPLETE, just flip the bit saying the command finished */
-	/* in the future we're going to have to pay attention to the actual command that completed */
-	if (data[0] == WHITEHEAT_CMD_COMPLETE) {
-		info->command_finished = WHITEHEAT_CMD_COMPLETE;
-		wake_up_interruptible(&info->wait_command);
+	info("%s: Driver %s: Firmware v%d.%02d", serial->type->name,
+	     DRIVER_VERSION, hw_info->sw_major_rev, hw_info->sw_minor_rev);
+
+	for (i = 0; i < serial->num_ports; i++) {
+		port = &serial->port[i];
+
+		info = (struct whiteheat_private *)kmalloc(sizeof(struct whiteheat_private), GFP_KERNEL);
+		if (info == NULL)
+			goto no_memory;
+
+		spin_lock_init(&info->lock);
+		info->flags = 0;
+		info->mcr = 0;
+		port->private = info;
 	}
-	
-	if (data[0] == WHITEHEAT_CMD_FAILURE) {
-		info->command_finished = WHITEHEAT_CMD_FAILURE;
-		wake_up_interruptible(&info->wait_command);
+
+	command_info = (struct whiteheat_command_private *)kmalloc(sizeof(struct whiteheat_command_private), GFP_KERNEL);
+	if (command_info == NULL)
+		goto no_memory;
+
+	spin_lock_init(&command_info->lock);
+	command_info->port_running = 0;
+	init_waitqueue_head(&command_info->wait_command);
+	command_port->private = command_info;
+	command_port->write_urb->complete = command_port_write_callback;
+	command_port->read_urb->complete = command_port_read_callback;
+
+	return 0;
+
+no_firmware:
+	/* Firmware likely not running */
+	err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->name);
+	err("%s: If the firmware is not running (status led not blinking)\n", serial->type->name);
+	err("%s: please contact support@connecttech.com\n", serial->type->name);
+	return -ENODEV;
+
+no_memory:
+	for (i--; i >= 0; i--) {
+		port = &serial->port[i];
+		kfree(port->private);
 	}
-	
-	/* Continue trying to always read */
-	FILL_BULK_URB(port->read_urb, serial->dev, 
-		      usb_rcvbulkpipe(serial->dev, port->bulk_in_endpointAddress),
-		      port->read_urb->transfer_buffer, port->read_urb->transfer_buffer_length,
-		      command_port_read_callback, port);
-	result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
-	if (result)
-		dbg("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
+	err("%s: Out of memory for port structures\n", serial->type->name);
+	return -ENOMEM;
 }
 
 
-static int whiteheat_send_cmd (struct usb_serial *serial, __u8 command, __u8 *data, __u8 datasize)
+static void whiteheat_shutdown (struct usb_serial *serial)
 {
-	struct whiteheat_private *info;
+	struct usb_serial_port *command_port;
 	struct usb_serial_port *port;
-	int timeout;
-	__u8 *transfer_buffer;
-	int retval = 0;
-
-	dbg("%s - command %d", __FUNCTION__, command);
-
-	port = &serial->port[COMMAND_PORT];
-	info = (struct whiteheat_private *)port->private;
-	info->command_finished = FALSE;
-	
-	transfer_buffer = (__u8 *)port->write_urb->transfer_buffer;
-	transfer_buffer[0] = command;
-	memcpy (&transfer_buffer[1], data, datasize);
-	port->write_urb->transfer_buffer_length = datasize + 1;
-	port->write_urb->dev = serial->dev;
-	retval = usb_submit_urb (port->write_urb, GFP_KERNEL);
-	if (retval) {
-		dbg("%s - submit urb failed", __FUNCTION__);
-		goto exit;
-	}
+	int i;
 
-	/* wait for the command to complete */
-	timeout = COMMAND_TIMEOUT;
-	while (timeout && (info->command_finished == FALSE)) {
-		timeout = interruptible_sleep_on_timeout (&info->wait_command, timeout);
-	}
+	dbg("%s", __FUNCTION__);
 
-	if (info->command_finished == FALSE) {
-		dbg("%s - command timed out.", __FUNCTION__);
-		retval = -ETIMEDOUT;
-		goto exit;
-	}
+	/* free up our private data for our command port */
+	command_port = &serial->port[COMMAND_PORT];
+	kfree (command_port->private);
+	command_port->private = NULL;
 
-	if (info->command_finished == WHITEHEAT_CMD_FAILURE) {
-		dbg("%s - command failed.", __FUNCTION__);
-		retval = -EIO;
-		goto exit;
+	for (i = 0; i < serial->num_ports; i++) {
+		port = &serial->port[i];
+		kfree(port->private);
+		port->private = NULL;
 	}
 
-	if (info->command_finished == WHITEHEAT_CMD_COMPLETE)
-		dbg("%s - command completed.", __FUNCTION__);
-
-exit:
-	return retval;
+	return;
 }
 
 
 static int whiteheat_open (struct usb_serial_port *port, struct file *filp)
 {
-	struct whiteheat_min_set	open_command;
-	struct usb_serial_port 		*command_port;
-	struct whiteheat_private	*info;
-	int				retval = 0;
+	int		retval = 0;
+	struct termios	old_term;
 
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	/* set up some stuff for our command port */
-	command_port = &port->serial->port[COMMAND_PORT];
-	if (command_port->private == NULL) {
-		info = (struct whiteheat_private *)kmalloc (sizeof(struct whiteheat_private), GFP_KERNEL);
-		if (info == NULL) {
-			err("%s - out of memory", __FUNCTION__);
-			retval = -ENOMEM;
-			goto exit;
-		}
-		
-		init_waitqueue_head(&info->wait_command);
-		command_port->private = info;
-		command_port->write_urb->complete = command_port_write_callback;
-		command_port->read_urb->complete = command_port_read_callback;
-		command_port->read_urb->dev = port->serial->dev;
-		command_port->tty = port->tty;		/* need this to "fake" our our sanity check macros */
-		retval = usb_submit_urb (command_port->read_urb, GFP_KERNEL);
-		if (retval) {
-			err("%s - failed submitting read urb, error %d", __FUNCTION__, retval);
-			goto exit;
-		}
-	}
-	
+	retval = start_command_port(port->serial);
+	if (retval)
+		goto exit;
+
 	/* Start reading from the device */
 	port->read_urb->dev = port->serial->dev;
 	retval = usb_submit_urb(port->read_urb, GFP_KERNEL);
 	if (retval) {
 		err("%s - failed submitting read urb, error %d", __FUNCTION__, retval);
+		stop_command_port(port->serial);
 		goto exit;
 	}
 
 	/* send an open port command */
-	/* firmware uses 1 based port numbering */
-	open_command.port = port->number - port->serial->minor + 1;
-	retval = whiteheat_send_cmd (port->serial, WHITEHEAT_OPEN, (__u8 *)&open_command, sizeof(open_command));
-	if (retval)
+	retval = firm_open(port);
+	if (retval) {
+		stop_command_port(port->serial);
+		goto exit;
+	}
+
+	retval = firm_purge(port, WHITEHEAT_PURGE_RX | WHITEHEAT_PURGE_TX);
+	if (retval) {
+		firm_close(port);
+		stop_command_port(port->serial);
 		goto exit;
+	}
 
-	/* Need to do device specific setup here (control lines, baud rate, etc.) */
-	/* FIXME!!! */
+	old_term.c_cflag = ~port->tty->termios->c_cflag;
+	old_term.c_iflag = ~port->tty->termios->c_iflag;
+	whiteheat_set_termios(port, &old_term);
+
+	retval = firm_set_rts(port, WHITEHEAT_RTS_ON);
+	if (retval) {
+		firm_close(port);
+		stop_command_port(port->serial);
+		goto exit;
+	}
+	retval = firm_set_dtr(port, WHITEHEAT_DTR_ON);
+	if (retval) {
+		firm_set_rts(port, WHITEHEAT_RTS_OFF);
+		firm_close(port);
+		stop_command_port(port->serial);
+		goto exit;
+	}
 
 exit:
 	dbg("%s - exit, retval = %d", __FUNCTION__, retval);
@@ -359,129 +487,259 @@ static int whiteheat_open (struct usb_serial_port *port, struct file *filp)
 
 static void whiteheat_close(struct usb_serial_port *port, struct file * filp)
 {
-	struct whiteheat_min_set	close_command;
-	
 	dbg("%s - port %d", __FUNCTION__, port->number);
 	
-	/* send a close command to the port */
-	/* firmware uses 1 based port numbering */
-	close_command.port = port->number - port->serial->minor + 1;
-	whiteheat_send_cmd (port->serial, WHITEHEAT_CLOSE, (__u8 *)&close_command, sizeof(close_command));
+	if (tty_hung_up_p(filp)) {
+		return;
+	}
+
+	port->tty->closing = 1;
+
+/*
+ * Not currently in use; tty_wait_until_sent() calls
+ * serial_chars_in_buffer() which deadlocks on the second semaphore
+ * acquisition. This should be fixed at some point. Greg's been
+ * notified.
+	if ((filp->f_flags & (O_NDELAY | O_NONBLOCK)) == 0) {
+		tty_wait_until_sent(port->tty, CLOSING_DELAY);
+	}
+*/
+
+	if (port->tty->driver.flush_buffer)
+		port->tty->driver.flush_buffer(port->tty);
+	if (port->tty->ldisc.flush_buffer)
+		port->tty->ldisc.flush_buffer(port->tty);
+
+	firm_report_tx_done(port);
+
+	firm_set_dtr(port, WHITEHEAT_DTR_OFF);
+	firm_set_rts(port, WHITEHEAT_RTS_OFF);
+
+	firm_close(port);
 
-	/* Need to change the control lines here */
-	/* FIXME */
-	
 	/* shutdown our bulk reads and writes */
 	usb_unlink_urb (port->write_urb);
 	usb_unlink_urb (port->read_urb);
-}
 
+	stop_command_port(port->serial);
 
-static int whiteheat_ioctl (struct usb_serial_port *port, struct file * file, unsigned int cmd, unsigned long arg)
-{
-	dbg("%s - port %d, cmd 0x%.4x", __FUNCTION__, port->number, cmd);
-
-	return -ENOIOCTLCMD;
+	port->tty->closing = 0;
 }
 
 
-static void whiteheat_set_termios (struct usb_serial_port *port, struct termios *old_termios)
+static int whiteheat_write(struct usb_serial_port *port, int from_user, const unsigned char *buf, int count)
 {
-	unsigned int cflag;
-	struct whiteheat_port_settings port_settings;
+	struct usb_serial *serial = port->serial;
+	int result;
 
-	dbg("%s -port %d", __FUNCTION__, port->number);
+	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	if ((!port->tty) || (!port->tty->termios)) {
-		dbg("%s - no tty structures", __FUNCTION__);
-		goto exit;
+	if (count == 0) {
+		dbg("%s - write request of 0 bytes", __FUNCTION__);
+		return (0);
 	}
-	
-	cflag = port->tty->termios->c_cflag;
-	/* check that they really want us to change something */
-	if (old_termios) {
-		if ((cflag == old_termios->c_cflag) &&
-		    (RELEVANT_IFLAG(port->tty->termios->c_iflag) == RELEVANT_IFLAG(old_termios->c_iflag))) {
-			dbg("%s - nothing to change...", __FUNCTION__);
-			goto exit;
-		}
+
+	if (port->write_urb->status == -EINPROGRESS) {
+		dbg ("%s - already writing", __FUNCTION__);
+		return (0);
 	}
 
-	/* set the port number */
-	/* firmware uses 1 based port numbering */
-	port_settings.port = port->number + 1;
+	count = (count > port->bulk_out_size) ? port->bulk_out_size : count;
 
-	/* get the byte size */
-	switch (cflag & CSIZE) {
-		case CS5:	port_settings.bits = 5;   break;
-		case CS6:	port_settings.bits = 6;   break;
-		case CS7:	port_settings.bits = 7;   break;
-		default:
-		case CS8:	port_settings.bits = 8;   break;
+	if (from_user) {
+		if (copy_from_user(port->write_urb->transfer_buffer, buf, count))
+			return -EFAULT;
+	}
+	else {
+		memcpy (port->write_urb->transfer_buffer, buf, count);
 	}
-	dbg("%s - data bits = %d", __FUNCTION__, port_settings.bits);
-	
-	/* determine the parity */
-	if (cflag & PARENB)
-		if (cflag & PARODD)
-			port_settings.parity = 'o';
-		else
-			port_settings.parity = 'e';
-	else
-		port_settings.parity = 'n';
-	dbg("%s - parity = %c", __FUNCTION__, port_settings.parity);
 
-	/* figure out the stop bits requested */
-	if (cflag & CSTOPB)
-		port_settings.stop = 2;
-	else
-		port_settings.stop = 1;
-	dbg("%s - stop bits = %d", __FUNCTION__, port_settings.stop);
+	usb_serial_debug_data (__FILE__, __FUNCTION__, count, port->write_urb->transfer_buffer);
 
-	
-	/* figure out the flow control settings */
-	if (cflag & CRTSCTS)
-		port_settings.hflow = (WHITEHEAT_CTS_FLOW | WHITEHEAT_RTS_FLOW);
-	else
-		port_settings.hflow = 0;
-	dbg("%s - hardware flow control = %s %s %s %s", __FUNCTION__,
-	    (port_settings.hflow & WHITEHEAT_CTS_FLOW) ? "CTS" : "",
-	    (port_settings.hflow & WHITEHEAT_RTS_FLOW) ? "RTS" : "",
-	    (port_settings.hflow & WHITEHEAT_DSR_FLOW) ? "DSR" : "",
-	    (port_settings.hflow & WHITEHEAT_DTR_FLOW) ? "DTR" : "");
-	
-	/* determine software flow control */
-	if (I_IXOFF(port->tty))
-		port_settings.sflow = 'b';
+	port->write_urb->dev = serial->dev;
+	port->write_urb->transfer_buffer_length = count;
+	result = usb_submit_urb(port->write_urb, GFP_ATOMIC);
+	if (result)
+		err("%s - failed submitting write urb, error %d", __FUNCTION__, result);
 	else
-		port_settings.sflow = 'n';
-	dbg("%s - software flow control = %c", __FUNCTION__, port_settings.sflow);
-	
-	port_settings.xon = START_CHAR(port->tty);
-	port_settings.xoff = STOP_CHAR(port->tty);
-	dbg("%s - XON = %2x, XOFF = %2x", __FUNCTION__, port_settings.xon, port_settings.xoff);
+		result = count;
 
-	/* get the baud rate wanted */
-	port_settings.baud = tty_get_baud_rate(port->tty);
-	dbg("%s - baud rate = %d", __FUNCTION__, port_settings.baud);
+	return result;
+}
 
-	/* handle any settings that aren't specified in the tty structure */
-	port_settings.lloop = 0;
+
+static int whiteheat_write_room(struct usb_serial_port *port)
+{
+	int room = 0;
+
+	dbg("%s - port %d", __FUNCTION__, port->number);
 	
-	/* now send the message to the device */
-	whiteheat_send_cmd (port->serial, WHITEHEAT_SETUP_PORT, (__u8 *)&port_settings, sizeof(port_settings));
+	if (port->write_urb->status != -EINPROGRESS)
+		room = port->bulk_out_size;
+
+	dbg("%s - returns %d", __FUNCTION__, room);
+	return (room);
+}
+
+
+static int whiteheat_ioctl (struct usb_serial_port *port, struct file * file, unsigned int cmd, unsigned long arg)
+{
+	struct whiteheat_private *info = (struct whiteheat_private *)port->private;
+	unsigned int modem_signals = 0;
+	struct serial_struct serstruct;
+
+	dbg("%s - port %d, cmd 0x%.4x", __FUNCTION__, port->number, cmd);
+
+	switch (cmd) {
+		case TIOCMGET:
+			firm_get_dtr_rts(port);
+			if (info->mcr & UART_MCR_DTR)
+				modem_signals |= TIOCM_DTR;
+			if (info->mcr & UART_MCR_RTS)
+				modem_signals |= TIOCM_RTS;
+			
+			if (copy_to_user((unsigned int *)arg, &modem_signals, sizeof(unsigned int)));
+				return -EFAULT;
+
+			break;
+
+		case TIOCMSET:
+			if (copy_from_user(&modem_signals, (unsigned int *)arg, sizeof(unsigned int)))
+				return -EFAULT;
+
+			if (modem_signals & TIOCM_DTR)
+				info->mcr |= UART_MCR_DTR;
+			else
+				info->mcr &= ~UART_MCR_DTR;
+			if (modem_signals & TIOCM_RTS)
+				info->mcr |= UART_MCR_RTS;
+			else
+				info->mcr &= ~UART_MCR_RTS;
+
+			firm_set_dtr(port, info->mcr & UART_MCR_DTR);
+			firm_set_rts(port, info->mcr & UART_MCR_RTS);
+
+			break;
+
+		case TIOCMBIS:
+			if (copy_from_user(&modem_signals, (unsigned int *)arg, sizeof(unsigned int)))
+				return -EFAULT;
+
+			if (modem_signals & TIOCM_DTR)
+				info->mcr |= UART_MCR_DTR;
+			if (modem_signals & TIOCM_RTS)
+				info->mcr |= UART_MCR_RTS;
+
+			firm_set_dtr(port, info->mcr & UART_MCR_DTR);
+			firm_set_rts(port, info->mcr & UART_MCR_RTS);
+
+			break;
+
+		case TIOCMBIC:
+			if (copy_from_user(&modem_signals, (unsigned int *)arg, sizeof(unsigned int)))
+				return -EFAULT;
+
+			if (modem_signals & TIOCM_DTR)
+				info->mcr &= ~UART_MCR_DTR;
+			if (modem_signals & TIOCM_RTS)
+				info->mcr &= ~UART_MCR_RTS;
+
+			firm_set_dtr(port, info->mcr & UART_MCR_DTR);
+			firm_set_rts(port, info->mcr & UART_MCR_RTS);
+
+			break;
+
+		case TIOCGSERIAL:
+			memset(&serstruct, 0, sizeof(serstruct));
+			serstruct.type = PORT_16654;
+			serstruct.line = port->serial->minor;
+			serstruct.port = port->number;
+			serstruct.flags = ASYNC_SKIP_TEST | ASYNC_AUTO_IRQ;
+			serstruct.xmit_fifo_size = port->bulk_out_size;
+			serstruct.custom_divisor = 0;
+			serstruct.baud_base = 460800;
+			serstruct.close_delay = CLOSING_DELAY;
+			serstruct.closing_wait = CLOSING_DELAY;
+
+			if (copy_to_user((void *)arg, &serstruct, sizeof(serstruct)))
+				return -EFAULT;
+
+			break;
+
+		case TIOCSSERIAL:
+			if (copy_from_user(&serstruct, (void *)arg, sizeof(serstruct)))
+				return -EFAULT;
+
+			/*
+			 * For now this is ignored. dip sets the ASYNC_[V]HI flags
+			 * but this isn't used by us at all. Maybe someone somewhere
+			 * will need the custom_divisor setting.
+			 */
+
+			break;
+
+		default:
+			return -ENOIOCTLCMD;
+	}
+
+	return 0;
+}
+
+
+static void whiteheat_set_termios (struct usb_serial_port *port, struct termios *old_termios)
+{
+	dbg("%s -port %d", __FUNCTION__, port->number);
+
+	if ((!port->tty) || (!port->tty->termios)) {
+		dbg("%s - no tty structures", __FUNCTION__);
+		goto exit;
+	}
 	
+	/* check that they really want us to change something */
+	if (old_termios) {
+		if ((port->tty->termios->c_cflag == old_termios->c_cflag) &&
+		    (RELEVANT_IFLAG(port->tty->termios->c_iflag) == RELEVANT_IFLAG(old_termios->c_iflag))) {
+			dbg("%s - nothing to change...", __FUNCTION__);
+			goto exit;
+		}
+	}
+
+	firm_setup_port(port);
+
 exit:
 	return;
 }
 
 
+static void whiteheat_break_ctl(struct usb_serial_port *port, int break_state) {
+	firm_set_break(port, break_state);
+}
+
+
+static int whiteheat_chars_in_buffer(struct usb_serial_port *port)
+{
+	int chars = 0;
+
+	dbg("%s - port %d", __FUNCTION__, port->number);
+
+	if (port->write_urb->status == -EINPROGRESS)
+		chars = port->write_urb->transfer_buffer_length;
+
+	dbg ("%s - returns %d", __FUNCTION__, chars);
+	return (chars);
+}
+
+
 static void whiteheat_throttle (struct usb_serial_port *port)
 {
+	struct whiteheat_private *info = (struct whiteheat_private *)port->private;
+	unsigned long flags;
+
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	/* Change the control signals */
-	/* FIXME!!! */
+	spin_lock_irqsave(&info->lock, flags);
+	info->flags |= THROTTLED;
+	spin_unlock_irqrestore(&info->lock, flags);
 
 	return;
 }
@@ -489,194 +747,441 @@ static void whiteheat_throttle (struct usb_serial_port *port)
 
 static void whiteheat_unthrottle (struct usb_serial_port *port)
 {
+	struct whiteheat_private *info = (struct whiteheat_private *)port->private;
+	int result;
+	unsigned long flags;
+
 	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	/* Change the control signals */
-	/* FIXME!!! */
+	spin_lock_irqsave(&info->lock, flags);
+
+	if (info->flags & ACTUALLY_THROTTLED) {
+		/* Continue trying to always read  */
+		port->read_urb->dev = port->serial->dev;
+		result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
+		if (result)
+			err("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
+	}
+
+	info->flags &= ~(THROTTLED | ACTUALLY_THROTTLED);
+
+	spin_unlock_irqrestore(&info->lock, flags);
 
 	return;
 }
 
 
-/* steps to download the firmware to the WhiteHEAT device:
- - hold the reset (by writing to the reset bit of the CPUCS register)
- - download the VEND_AX.HEX file to the chip using VENDOR_REQUEST-ANCHOR_LOAD
- - release the reset (by writing to the CPUCS register)
- - download the WH.HEX file for all addresses greater than 0x1b3f using
-   VENDOR_REQUEST-ANCHOR_EXTERNAL_RAM_LOAD
- - hold the reset
- - download the WH.HEX file for all addresses less than 0x1b40 using
-   VENDOR_REQUEST_ANCHOR_LOAD
- - release the reset
- - device renumerated itself and comes up as new device id with all
-   firmware download completed.
-*/
-static int whiteheat_firmware_download (struct usb_serial *serial)
+/*****************************************************************************
+ * Connect Tech's White Heat callback routines
+ *****************************************************************************/
+static void command_port_write_callback (struct urb *urb)
 {
-	int response;
-	const struct whiteheat_hex_record *record;
-	
 	dbg("%s", __FUNCTION__);
-	
-	response = ezusb_set_reset (serial, 1);
 
-	record = &whiteheat_loader[0];
-	while (record->address != 0xffff) {
-		response = ezusb_writememory (serial, record->address, 
-				(unsigned char *)record->data, record->data_size, 0xa0);
-		if (response < 0) {
-			err("%s - ezusb_writememory failed for loader (%d %04X %p %d)",
-				__FUNCTION__, response, record->address, record->data, record->data_size);
-			break;
-		}
-		++record;
+	if (urb->status) {
+		dbg ("nonzero urb status: %d", urb->status);
+		return;
 	}
 
-	response = ezusb_set_reset (serial, 0);
+	usb_serial_debug_data (__FILE__, __FUNCTION__, urb->actual_length, urb->transfer_buffer);
 
-	record = &whiteheat_firmware[0];
-	while (record->address < 0x1b40) {
-		++record;
+	return;
+}
+
+
+static void command_port_read_callback (struct urb *urb)
+{
+	struct usb_serial_port *command_port = (struct usb_serial_port *)urb->context;
+	struct usb_serial *serial = get_usb_serial (command_port, __FUNCTION__);
+	struct whiteheat_command_private *command_info;
+	unsigned char *data = urb->transfer_buffer;
+	int result;
+	unsigned long flags;
+
+	dbg("%s", __FUNCTION__);
+
+	if (urb->status) {
+		dbg("%s - nonzero urb status: %d", __FUNCTION__, urb->status);
+		return;
 	}
-	while (record->address != 0xffff) {
-		response = ezusb_writememory (serial, record->address, 
-				(unsigned char *)record->data, record->data_size, 0xa3);
-		if (response < 0) {
-			err("%s - ezusb_writememory failed for first firmware step (%d %04X %p %d)", 
-				__FUNCTION__, response, record->address, record->data, record->data_size);
-			break;
-		}
-		++record;
+
+	if (!serial) {
+		dbg("%s - bad serial pointer, exiting", __FUNCTION__);
+		return;
 	}
 	
-	response = ezusb_set_reset (serial, 1);
+	usb_serial_debug_data (__FILE__, __FUNCTION__, urb->actual_length, data);
 
-	record = &whiteheat_firmware[0];
-	while (record->address < 0x1b40) {
-		response = ezusb_writememory (serial, record->address, 
-				(unsigned char *)record->data, record->data_size, 0xa0);
-		if (response < 0) {
-			err("%s - ezusb_writememory failed for second firmware step (%d %04X %p %d)", 
-				__FUNCTION__, response, record->address, record->data, record->data_size);
-			break;
-		}
-		++record;
+	command_info = (struct whiteheat_command_private *)command_port->private;
+	if (!command_info) {
+		dbg ("%s - command_info is NULL, exiting.", __FUNCTION__);
+		return;
 	}
+	spin_lock_irqsave(&command_info->lock, flags);
 
-	response = ezusb_set_reset (serial, 0);
-
-	/* we want this device to fail to have a driver assigned to it. */
-	return 1;
+	if (data[0] == WHITEHEAT_CMD_COMPLETE) {
+		command_info->command_finished = WHITEHEAT_CMD_COMPLETE;
+		wake_up_interruptible(&command_info->wait_command);
+	} else if (data[0] == WHITEHEAT_CMD_FAILURE) {
+		command_info->command_finished = WHITEHEAT_CMD_FAILURE;
+		wake_up_interruptible(&command_info->wait_command);
+	} else if (data[0] == WHITEHEAT_EVENT) {
+		/* These are unsolicited reports from the firmware, hence no waiting command to wakeup */
+		dbg("%s - event received", __FUNCTION__);
+	} else if (data[0] == WHITEHEAT_GET_DTR_RTS) {
+		memcpy(command_info->result_buffer, &data[1], urb->actual_length - 1);
+		command_info->command_finished = WHITEHEAT_CMD_COMPLETE;
+		wake_up_interruptible(&command_info->wait_command);
+	} else {
+		dbg("%s - bad reply from firmware", __FUNCTION__);
+	}
+	
+	/* Continue trying to always read */
+	command_port->read_urb->dev = serial->dev;
+	result = usb_submit_urb(command_port->read_urb, GFP_ATOMIC);
+	spin_unlock_irqrestore(&command_info->lock, flags);
+	if (result)
+		dbg("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
 }
 
 
-static int whiteheat_attach (struct usb_serial *serial)
+static void whiteheat_read_callback(struct urb *urb)
 {
-	struct whiteheat_hw_info *hw_info;
-	int pipe;
-	int ret;
-	int alen;
-	__u8 command[2] = { WHITEHEAT_GET_HW_INFO, 0 };
-	__u8 result[sizeof(*hw_info) + 1];
+	struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
+	struct usb_serial *serial = get_usb_serial (port, __FUNCTION__);
+	struct tty_struct *tty;
+	unsigned char *data = urb->transfer_buffer;
+	int i;
+	int result;
+	struct whiteheat_private *info = (struct whiteheat_private *)port->private;
+	unsigned long flags;
 
-	pipe = usb_rcvbulkpipe (serial->dev, 7);
-	usb_bulk_msg (serial->dev, pipe, result, sizeof(result), &alen, 2 * HZ);
-	/*
-	 * We ignore the return code. In the case where rmmod/insmod is
-	 * performed with a WhiteHEAT connected, the above times out
-	 * because the endpoint is already prepped, meaning the below succeeds
-	 * regardless. All other cases the above succeeds.
-	 */
-
-	pipe = usb_sndbulkpipe (serial->dev, 7);
-	ret = usb_bulk_msg (serial->dev, pipe, command, sizeof(command), &alen, 2 * HZ);
-	if (ret) {
-		err("%s: Couldn't send command [%d]", serial->type->name, ret);
-		goto error_out;
-	} else if (alen != sizeof(command)) {
-		err("%s: Send command incomplete [%d]", serial->type->name, alen);
-		goto error_out;
+	dbg("%s - port %d", __FUNCTION__, port->number);
+
+	if (!serial) {
+		dbg("%s - bad serial pointer, exiting", __FUNCTION__);
+		return;
 	}
 
-	pipe = usb_rcvbulkpipe (serial->dev, 7);
-	ret = usb_bulk_msg (serial->dev, pipe, result, sizeof(result), &alen, 2 * HZ);
-	if (ret) {
-		err("%s: Couldn't get results [%d]", serial->type->name, ret);
-		goto error_out;
-	} else if (alen != sizeof(result)) {
-		err("%s: Get results incomplete [%d]", serial->type->name, alen);
-		goto error_out;
-	} else if (result[0] != command[0]) {
-		err("%s: Command failed [%d]", serial->type->name, result[0]);
-		goto error_out;
+	if (urb->status) {
+		dbg("%s - nonzero read bulk status received: %d", __FUNCTION__, urb->status);
+		return;
 	}
 
-	hw_info = (struct whiteheat_hw_info *)&result[1];
+	usb_serial_debug_data (__FILE__, __FUNCTION__, urb->actual_length, data);
 
-	info("%s: Driver %s: Firmware v%d.%02d", serial->type->name,
-	     DRIVER_VERSION, hw_info->sw_major_rev, hw_info->sw_minor_rev);
+	tty = port->tty;
+	if (tty && urb->actual_length) {
+		for (i = 0; i < urb->actual_length ; ++i) {
+			/* if we insert more than TTY_FLIPBUF_SIZE characters, we drop them. */
+			if(tty->flip.count >= TTY_FLIPBUF_SIZE) {
+				tty_flip_buffer_push(tty);
+			}
+			/* this doesn't actually push the data through unless tty->low_latency is set */
+			tty_insert_flip_char(tty, data[i], 0);
+		}
+	  	tty_flip_buffer_push(tty);
+	}
 
-	return 0;
+	spin_lock_irqsave(&info->lock, flags);
+	if (info->flags & THROTTLED) {
+		info->flags |= ACTUALLY_THROTTLED;
+		spin_unlock_irqrestore(&info->lock, flags);
+		return;
+	}
+	spin_unlock_irqrestore(&info->lock, flags);
 
-error_out:
-	err("%s: Unable to retrieve firmware version, try replugging\n", serial->type->name);
-	/*
-	 * Return that we've claimed the interface. A failure here may be
-	 * due to interception by the command_callback routine or other
-	 * causes that don't mean that the firmware isn't running. This may
-	 * change in the future. Probably should actually.
-	 */
-	return 0;
+	/* Continue trying to always read  */
+	port->read_urb->dev = serial->dev;
+	result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
+	if (result)
+		err("%s - failed resubmitting read urb, error %d", __FUNCTION__, result);
 }
 
-static void whiteheat_shutdown (struct usb_serial *serial)
+
+static void whiteheat_write_callback(struct urb *urb)
 {
-	struct usb_serial_port *command_port;
+	struct usb_serial_port *port = (struct usb_serial_port *)urb->context;
+	struct usb_serial *serial = get_usb_serial (port, __FUNCTION__);
 
-	dbg("%s", __FUNCTION__);
+	dbg("%s - port %d", __FUNCTION__, port->number);
 
-	/* free up our private data for our command port */
-	command_port = &serial->port[COMMAND_PORT];
-	if (command_port->private != NULL) {
-		kfree (command_port->private);
-		command_port->private = NULL;
+	if (!serial) {
+		dbg("%s - bad serial pointer, exiting", __FUNCTION__);
+		return;
 	}
 
+	if (urb->status) {
+		dbg("%s - nonzero write bulk status received: %d", __FUNCTION__, urb->status);
+		return;
+	}
+
+	usb_serial_port_softint((void *)port);
+
+	queue_task(&port->tqueue, &tq_immediate);
+	mark_bh(IMMEDIATE_BH);
+
 	return;
 }
 
 
-static void set_command (struct usb_serial_port *port, unsigned char state, unsigned char command)
+/*****************************************************************************
+ * Connect Tech's White Heat firmware interface
+ *****************************************************************************/
+static int firm_send_command (struct usb_serial_port *port, __u8 command, __u8 *data, __u8 datasize)
 {
-	struct whiteheat_rdb_set rdb_command;
+	struct usb_serial_port *command_port;
+	struct whiteheat_command_private *command_info;
+	struct whiteheat_private *info;
+	int timeout;
+	__u8 *transfer_buffer;
+	int retval = 0;
+	unsigned long flags;
+
+	dbg("%s - command %d", __FUNCTION__, command);
+
+	command_port = &port->serial->port[COMMAND_PORT];
+	command_info = (struct whiteheat_command_private *)command_port->private;
+	spin_lock_irqsave(&command_info->lock, flags);
+	command_info->command_finished = FALSE;
 	
-	/* send a set rts command to the port */
-	/* firmware uses 1 based port numbering */
-	rdb_command.port = port->number - port->serial->minor + 1;
-	rdb_command.state = state;
+	transfer_buffer = (__u8 *)command_port->write_urb->transfer_buffer;
+	transfer_buffer[0] = command;
+	memcpy (&transfer_buffer[1], data, datasize);
+	command_port->write_urb->transfer_buffer_length = datasize + 1;
+	command_port->write_urb->dev = port->serial->dev;
+	retval = usb_submit_urb (command_port->write_urb, GFP_KERNEL);
+	spin_unlock_irqrestore(&command_info->lock, flags);
+	if (retval) {
+		dbg("%s - submit urb failed", __FUNCTION__);
+		goto exit;
+	}
+
+	/* wait for the command to complete */
+	timeout = COMMAND_TIMEOUT;
+	while (timeout && (command_info->command_finished == FALSE)) {
+		timeout = interruptible_sleep_on_timeout (&command_info->wait_command, timeout);
+	}
+
+	spin_lock_irqsave(&command_info->lock, flags);
 
-	whiteheat_send_cmd (port->serial, command, (__u8 *)&rdb_command, sizeof(rdb_command));
+	if (command_info->command_finished == FALSE) {
+		dbg("%s - command timed out.", __FUNCTION__);
+		retval = -ETIMEDOUT;
+		goto exit;
+	}
+
+	if (command_info->command_finished == WHITEHEAT_CMD_FAILURE) {
+		dbg("%s - command failed.", __FUNCTION__);
+		retval = -EIO;
+		goto exit;
+	}
+
+	if (command_info->command_finished == WHITEHEAT_CMD_COMPLETE) {
+		dbg("%s - command completed.", __FUNCTION__);
+		switch (command) {
+			case WHITEHEAT_GET_DTR_RTS:
+				info = (struct whiteheat_private *)port->private;
+				memcpy(&info->mcr, command_info->result_buffer, sizeof(struct whiteheat_dr_info));
+				break;
+		}
+	}
+
+exit:
+	spin_unlock_irqrestore(&command_info->lock, flags);
+	return retval;
 }
 
 
-static inline void set_rts (struct usb_serial_port *port, unsigned char rts)
-{
-	set_command (port, rts, WHITEHEAT_SET_RTS);
+static int firm_open(struct usb_serial_port *port) {
+	struct whiteheat_simple open_command;
+
+	open_command.port = port->number - port->serial->minor + 1;
+	return firm_send_command(port, WHITEHEAT_OPEN, (__u8 *)&open_command, sizeof(open_command));
 }
 
 
-static inline void set_dtr (struct usb_serial_port *port, unsigned char dtr)
+static int firm_close(struct usb_serial_port *port) {
+	struct whiteheat_simple close_command;
+
+	close_command.port = port->number - port->serial->minor + 1;
+	return firm_send_command(port, WHITEHEAT_CLOSE, (__u8 *)&close_command, sizeof(close_command));
+}
+
+
+static int firm_setup_port(struct usb_serial_port *port) {
+	struct whiteheat_port_settings port_settings;
+	unsigned int cflag = port->tty->termios->c_cflag;
+
+	port_settings.port = port->number + 1;
+
+	/* get the byte size */
+	switch (cflag & CSIZE) {
+		case CS5:	port_settings.bits = 5;   break;
+		case CS6:	port_settings.bits = 6;   break;
+		case CS7:	port_settings.bits = 7;   break;
+		default:
+		case CS8:	port_settings.bits = 8;   break;
+	}
+	dbg("%s - data bits = %d", __FUNCTION__, port_settings.bits);
+	
+	/* determine the parity */
+	if (cflag & PARENB)
+		if (cflag & CMSPAR)
+			if (cflag & PARODD)
+				port_settings.parity = WHITEHEAT_PAR_MARK;
+			else
+				port_settings.parity = WHITEHEAT_PAR_SPACE;
+		else
+			if (cflag & PARODD)
+				port_settings.parity = WHITEHEAT_PAR_ODD;
+			else
+				port_settings.parity = WHITEHEAT_PAR_EVEN;
+	else
+		port_settings.parity = WHITEHEAT_PAR_NONE;
+	dbg("%s - parity = %c", __FUNCTION__, port_settings.parity);
+
+	/* figure out the stop bits requested */
+	if (cflag & CSTOPB)
+		port_settings.stop = 2;
+	else
+		port_settings.stop = 1;
+	dbg("%s - stop bits = %d", __FUNCTION__, port_settings.stop);
+
+	/* figure out the flow control settings */
+	if (cflag & CRTSCTS)
+		port_settings.hflow = (WHITEHEAT_HFLOW_CTS | WHITEHEAT_HFLOW_RTS);
+	else
+		port_settings.hflow = WHITEHEAT_HFLOW_NONE;
+	dbg("%s - hardware flow control = %s %s %s %s", __FUNCTION__,
+	    (port_settings.hflow & WHITEHEAT_HFLOW_CTS) ? "CTS" : "",
+	    (port_settings.hflow & WHITEHEAT_HFLOW_RTS) ? "RTS" : "",
+	    (port_settings.hflow & WHITEHEAT_HFLOW_DSR) ? "DSR" : "",
+	    (port_settings.hflow & WHITEHEAT_HFLOW_DTR) ? "DTR" : "");
+	
+	/* determine software flow control */
+	if (I_IXOFF(port->tty))
+		port_settings.sflow = WHITEHEAT_SFLOW_RXTX;
+	else
+		port_settings.sflow = WHITEHEAT_SFLOW_NONE;
+	dbg("%s - software flow control = %c", __FUNCTION__, port_settings.sflow);
+	
+	port_settings.xon = START_CHAR(port->tty);
+	port_settings.xoff = STOP_CHAR(port->tty);
+	dbg("%s - XON = %2x, XOFF = %2x", __FUNCTION__, port_settings.xon, port_settings.xoff);
+
+	/* get the baud rate wanted */
+	port_settings.baud = tty_get_baud_rate(port->tty);
+	dbg("%s - baud rate = %d", __FUNCTION__, port_settings.baud);
+
+	/* handle any settings that aren't specified in the tty structure */
+	port_settings.lloop = 0;
+	
+	/* now send the message to the device */
+	return firm_send_command(port, WHITEHEAT_SETUP_PORT, (__u8 *)&port_settings, sizeof(port_settings));
+}
+
+
+static int firm_set_rts(struct usb_serial_port *port, __u8 onoff) {
+	struct whiteheat_set_rdb rts_command;
+
+	rts_command.port = port->number - port->serial->minor + 1;
+	rts_command.state = onoff;
+	return firm_send_command(port, WHITEHEAT_SET_RTS, (__u8 *)&rts_command, sizeof(rts_command));
+}
+
+
+static int firm_set_dtr(struct usb_serial_port *port, __u8 onoff) {
+	struct whiteheat_set_rdb dtr_command;
+
+	dtr_command.port = port->number - port->serial->minor + 1;
+	dtr_command.state = onoff;
+	return firm_send_command(port, WHITEHEAT_SET_RTS, (__u8 *)&dtr_command, sizeof(dtr_command));
+}
+
+
+static int firm_set_break(struct usb_serial_port *port, __u8 onoff) {
+	struct whiteheat_set_rdb break_command;
+
+	break_command.port = port->number - port->serial->minor + 1;
+	break_command.state = onoff;
+	return firm_send_command(port, WHITEHEAT_SET_RTS, (__u8 *)&break_command, sizeof(break_command));
+}
+
+
+static int firm_purge(struct usb_serial_port *port, __u8 rxtx) {
+	struct whiteheat_purge purge_command;
+
+	purge_command.port = port->number - port->serial->minor + 1;
+	purge_command.what = rxtx;
+	return firm_send_command(port, WHITEHEAT_PURGE, (__u8 *)&purge_command, sizeof(purge_command));
+}
+
+
+static int firm_get_dtr_rts(struct usb_serial_port *port) {
+	struct whiteheat_simple get_dr_command;
+
+	get_dr_command.port = port->number - port->serial->minor + 1;
+	return firm_send_command(port, WHITEHEAT_GET_DTR_RTS, (__u8 *)&get_dr_command, sizeof(get_dr_command));
+}
+
+
+static int firm_report_tx_done(struct usb_serial_port *port) {
+	struct whiteheat_simple close_command;
+
+	close_command.port = port->number - port->serial->minor + 1;
+	return firm_send_command(port, WHITEHEAT_REPORT_TX_DONE, (__u8 *)&close_command, sizeof(close_command));
+}
+
+
+/*****************************************************************************
+ * Connect Tech's White Heat utility functions
+ *****************************************************************************/
+static int start_command_port(struct usb_serial *serial)
 {
-	set_command (port, dtr, WHITEHEAT_SET_DTR);
+	struct usb_serial_port *command_port;
+	struct whiteheat_command_private *command_info;
+	unsigned long flags;
+	int retval = 0;
+	
+	command_port = &serial->port[COMMAND_PORT];
+	command_info = (struct whiteheat_command_private *)command_port->private;
+	spin_lock_irqsave(&command_info->lock, flags);
+	if (!command_info->port_running) {
+		command_port->read_urb->dev = serial->dev;
+		retval = usb_submit_urb(command_port->read_urb, GFP_KERNEL);
+		if (retval) {
+			err("%s - failed submitting read urb, error %d", __FUNCTION__, retval);
+			goto exit;
+		}
+	}
+	command_info->port_running++;
+
+exit:
+	spin_unlock_irqrestore(&command_info->lock, flags);
+	return retval;
 }
 
 
-static inline void set_break (struct usb_serial_port *port, unsigned char brk)
+static void stop_command_port(struct usb_serial *serial)
 {
-	set_command (port, brk, WHITEHEAT_SET_BREAK);
+	struct usb_serial_port *command_port;
+	struct whiteheat_command_private *command_info;
+	unsigned long flags;
+
+	command_port = &serial->port[COMMAND_PORT];
+	command_info = (struct whiteheat_command_private *)command_port->private;
+	spin_lock_irqsave(&command_info->lock, flags);
+	command_info->port_running--;
+	if (!command_info->port_running)
+		usb_unlink_urb(command_port->read_urb);
+	spin_unlock_irqrestore(&command_info->lock, flags);
 }
 
 
+/*****************************************************************************
+ * Connect Tech's White Heat module functions
+ *****************************************************************************/
 static int __init whiteheat_init (void)
 {
 	usb_serial_register (&whiteheat_fake_device);
@@ -704,4 +1209,3 @@ MODULE_LICENSE("GPL");
 
 MODULE_PARM(debug, "i");
 MODULE_PARM_DESC(debug, "Debug enabled or not");
-

drivers/usb/serial/whiteheat.h

 /*
  * USB ConnectTech WhiteHEAT driver
  *
+ *      Copyright (C) 2002
+ *          Connect Tech Inc.	
+ *
  *      Copyright (C) 1999, 2000
  *          Greg Kroah-Hartman (greg@kroah.com)
  *
@@ -17,8 +20,9 @@
 #define __LINUX_USB_SERIAL_WHITEHEAT_H
 
 
-#define FALSE				0
-#define TRUE				1
+#define FALSE	0
+#define TRUE	1
+
 
 /* WhiteHEAT commands */
 #define WHITEHEAT_OPEN			1	/* open the port */
@@ -39,109 +43,192 @@
 #define WHITEHEAT_CMD_COMPLETE		16	/* reply for certain commands */
 #define WHITEHEAT_CMD_FAILURE		17	/* reply for failed commands */
 
-/* Data for the WHITEHEAT_SETUP_PORT command */
-#define WHITEHEAT_CTS_FLOW		0x08
-#define WHITEHEAT_RTS_FLOW		0x80
-#define WHITEHEAT_DSR_FLOW		0x10
-#define WHITEHEAT_DTR_FLOW		0x02
+
+/*
+ * Commands to the firmware
+ */
+
+
+/*
+ * WHITEHEAT_OPEN
+ * WHITEHEAT_CLOSE
+ * WHITEHEAT_STATUS
+ * WHITEHEAT_GET_DTR_RTS
+ * WHITEHEAT_REPORT_TX_DONE
+*/
+struct whiteheat_simple {
+	__u8	port;	/* port number (1 to N) */
+};
+
+
+/*
+ * WHITEHEAT_SETUP_PORT
+ */
+#define WHITEHEAT_PAR_NONE	'n'	/* no parity */
+#define WHITEHEAT_PAR_EVEN	'e'	/* even parity */
+#define WHITEHEAT_PAR_ODD	'o'	/* odd parity */
+#define WHITEHEAT_PAR_SPACE	'0'	/* space (force 0) parity */
+#define WHITEHEAT_PAR_MARK	'1'	/* mark (force 1) parity */
+
+#define WHITEHEAT_SFLOW_NONE	'n'	/* no software flow control */
+#define WHITEHEAT_SFLOW_RX	'r'	/* XOFF/ON is sent when RX fills/empties */
+#define WHITEHEAT_SFLOW_TX	't'	/* when received XOFF/ON will stop/start TX */
+#define WHITEHEAT_SFLOW_RXTX	'b'	/* both SFLOW_RX and SFLOW_TX */
+
+#define WHITEHEAT_HFLOW_NONE		0x00	/* no hardware flow control */
+#define WHITEHEAT_HFLOW_RTS_TOGGLE	0x01	/* RTS is on during transmit, off otherwise */
+#define WHITEHEAT_HFLOW_DTR		0x02	/* DTR is off/on when RX fills/empties */
+#define WHITEHEAT_HFLOW_CTS		0x08	/* when received CTS off/on will stop/start TX */
+#define WHITEHEAT_HFLOW_DSR		0x10	/* when received DSR off/on will stop/start TX */
+#define WHITEHEAT_HFLOW_RTS		0x80	/* RTS is off/on when RX fills/empties */
+
 struct whiteheat_port_settings {
 	__u8	port;		/* port number (1 to N) */
-	__u32	baud;		/* any value allowed, default 9600, arrives little endian, range is 7 - 460800 */
-	__u8	bits;		/* 5, 6, 7, or 8, default 8 */
+	__u32	baud;		/* any value 7 - 460800, firmware calculates best fit; arrives little endian */
+	__u8	bits;		/* 5, 6, 7, or 8 */
 	__u8	stop;		/* 1 or 2, default 1 (2 = 1.5 if bits = 5) */
-	__u8	parity;		/* 'n, e, o, 0, or 1' (ascii), default 'n'
-				 *	n = none	e = even	o = odd
-				 *	0 = force 0	1 = force 1	*/
-	__u8	sflow;		/* 'n, r, t, or b' (ascii), default 'n'
-				 *	n = none
-				 *	r = receive (XOFF/XON transmitted when receiver fills / empties)
-				 *	t = transmit (XOFF/XON received will stop/start TX)
-				 *	b = both 	*/
-	__u8	xoff;		/* XOFF byte value, default 0x13 */
-	__u8	xon;		/* XON byte value, default 0x11 */
-	__u8	hflow;		/* bits indicate mode as follows:
-				 *	CTS (0x08) (CTS off/on will control/cause TX off/on)
-				 *	DSR (0x10) (DSR off/on will control/cause TX off/on)
-				 *	RTS (0x80) (RTS off/on when receiver fills/empties)
-				 *	DTR (0x02) (DTR off/on when receiver fills/empties) */
-	__u8	lloop;		/* local loopback 0 or 1, default 0 */
+	__u8	parity;		/* see WHITEHEAT_PAR_* above */
+	__u8	sflow;		/* see WHITEHEAT_SFLOW_* above */
+	__u8	xoff;		/* XOFF byte value */
+	__u8	xon;		/* XON byte value */
+	__u8	hflow;		/* see WHITEHEAT_HFLOW_* above */
+	__u8	lloop;		/* 0/1 turns local loopback mode off/on */
 } __attribute__ ((packed));
 
-/* data for WHITEHEAT_SET_RTS, WHITEHEAT_SET_DTR, and WHITEHEAT_SET_BREAK commands */
-struct whiteheat_rdb_set {
+
+/*
+ * WHITEHEAT_SET_RTS
+ * WHITEHEAT_SET_DTR
+ * WHITEHEAT_SET_BREAK
+ */
+#define WHITEHEAT_RTS_OFF	0x00
+#define WHITEHEAT_RTS_ON	0x01
+#define WHITEHEAT_DTR_OFF	0x00
+#define WHITEHEAT_DTR_ON	0x01
+#define WHITEHEAT_BREAK_OFF	0x00
+#define WHITEHEAT_BREAK_ON	0x01
+
+struct whiteheat_set_rdb {
 	__u8	port;		/* port number (1 to N) */
-	__u8	state;		/* 0 = off, non-zero = on */
+	__u8	state;		/* 0/1 turns signal off/on */
 };
 
-/* data for:
-	WHITEHEAT_OPEN
-	WHITEHEAT_CLOSE
-	WHITEHEAT_STATUS
-	WHITEHEAT_GET_DTR_RTS
-	WHITEHEAT_REPORT_TX_DONE */
-struct whiteheat_min_set {
-	__u8	port;		/* port number (1 to N) */
+
+/*
+ * WHITEHEAT_DUMP
+ */
+#define WHITEHEAT_DUMP_MEM_DATA		'd'  /* data */
+#define WHITEHEAT_DUMP_MEM_IDATA	'i'  /* idata */
+#define WHITEHEAT_DUMP_MEM_BDATA	'b'  /* bdata */
+#define WHITEHEAT_DUMP_MEM_XDATA	'x'  /* xdata */
+
+/*
+ * Allowable address ranges (firmware checks address):
+ * Type DATA:  0x00 - 0xff
+ * Type IDATA: 0x80 - 0xff
+ * Type BDATA: 0x20 - 0x2f
+ * Type XDATA: 0x0000 - 0xffff
+ *
+ * B/I/DATA all read the local memory space
+ * XDATA reads the external memory space
+ * BDATA returns bits as bytes
+ *
+ * NOTE: 0x80 - 0xff (local space) are the Special Function Registers
+ *       of the 8051, and some have on-read side-effects.
+ */
+
+struct whiteheat_dump {
+	__u8	mem_type;	/* see WHITEHEAT_DUMP_* above */
+	__u16	addr;		/* address, see restrictions above */
+	__u16	length;		/* number of bytes to dump, max 63 bytes */
 };
 
-/* data for WHITEHEAT_PURGE command */
-#define WHITEHEAT_PURGE_INPUT		0x01
-#define WHITEHEAT_PURGE_OUTPUT		0x02
-struct whiteheat_purge_set {
+
+/*
+ * WHITEHEAT_PURGE
+ */
+#define WHITEHEAT_PURGE_RX	0x01	/* purge rx fifos */
+#define WHITEHEAT_PURGE_TX	0x02	/* purge tx fifos */
+
+struct whiteheat_purge {
 	__u8	port;		/* port number (1 to N) */
 	__u8	what;		/* bit pattern of what to purge */
 };
 
-/* data for WHITEHEAT_DUMP command */
-struct whiteheat_dump_info {
-	__u8	mem_type;	/* memory type: 'd' = data, 'i' = idata, 'b' = bdata, 'x' = xdata */
-	__u16	addr;		/* memory address to dump, address range depends on the above mem_type:
-				 *	'd' = 0 to ff (80 to FF is SFR's)
-				 *	'i' = 80 to ff
-				 *	'b' = 20 to 2f (bits returned as bytes)
-				 *	'x' = 0000 to ffff (also code space)	*/
-	__u16	length;		/* number of bytes to dump, max 64 */
-};
 
-/* data for WHITEHEAT_ECHO command */
-struct whiteheat_echo_set {
+/*
+ * WHITEHEAT_ECHO
+ */
+struct whiteheat_echo {
 	__u8	port;		/* port number (1 to N) */
-	__u8	length;		/* length of message to echo */
+	__u8	length;		/* length of message to echo, max 61 bytes */
 	__u8	echo_data[61];	/* data to echo */
 };
 
-/* data returned from WHITEHEAT_STATUS command */
-#define WHITEHEAT_OVERRUN_ERROR		0x02
-#define WHITEHEAT_PARITY_ERROR		0x04
-#define WHITEHEAT_FRAMING_ERROR		0x08
-#define WHITEHEAT_BREAK_ERROR		0x10
-
-#define WHITEHEAT_OHFLOW		0x01	/* TX is stopped by CTS (waiting for CTS to go ON) */
-#define WHITEHEAT_IHFLOW		0x02	/* remote TX is stopped by RTS */
-#define WHITEHEAT_OSFLOW		0x04	/* TX is stopped by XOFF received (waiting for XON to occur) */
-#define WHITEHEAT_ISFLOW		0x08	/* remote TX is stopped by XOFF transmitted */
-#define WHITEHEAT_TX_DONE		0x80	/* TX has completed */
-
-#define WHITEHEAT_MODEM_EVENT		0x01
-#define WHITEHEAT_ERROR_EVENT		0x02
-#define WHITEHEAT_FLOW_EVENT		0x04
-#define WHITEHEAT_CONNECT_EVENT		0x08
+
+/*
+ * WHITEHEAT_DO_TEST
+ */
+#define WHITEHEAT_TEST_UART_RW		0x01  /* read/write uart registers */
+#define WHITEHEAT_TEST_UART_INTR	0x02  /* uart interrupt */
+#define WHITEHEAT_TEST_SETUP_CONT	0x03  /* setup for PORT_CONT/PORT_DISCONT */
+#define WHITEHEAT_TEST_PORT_CONT	0x04  /* port connect */
+#define WHITEHEAT_TEST_PORT_DISCONT	0x05  /* port disconnect */
+#define WHITEHEAT_TEST_UART_CLK_START	0x06  /* uart clock test start */
+#define WHITEHEAT_TEST_UART_CLK_STOP	0x07  /* uart clock test stop */
+#define WHITEHEAT_TEST_MODEM_FT		0x08  /* modem signals, requires a loopback cable/connector */
+#define WHITEHEAT_TEST_ERASE_EEPROM	0x09  /* erase eeprom */
+#define WHITEHEAT_TEST_READ_EEPROM	0x0a  /* read eeprom */
+#define WHITEHEAT_TEST_PROGRAM_EEPROM	0x0b  /* program eeprom */
+
+struct whiteheat_test {
+	__u8	port;		/* port number (1 to n) */
+	__u8	test;		/* see WHITEHEAT_TEST_* above*/
+	__u8	info[32];	/* additional info */
+};
+
+
+/*
+ * Replies from the firmware
+ */
+
+
+/*
+ * WHITEHEAT_STATUS
+ */
+#define WHITEHEAT_EVENT_MODEM		0x01	/* modem field is valid */
+#define WHITEHEAT_EVENT_ERROR		0x02	/* error field is valid */
+#define WHITEHEAT_EVENT_FLOW		0x04	/* flow field is valid */
+#define WHITEHEAT_EVENT_CONNECT		0x08	/* connect field is valid */
+
+#define WHITEHEAT_FLOW_NONE		0x00	/* no flow control active */
+#define WHITEHEAT_FLOW_HARD_OUT		0x01	/* TX is stopped by CTS (waiting for CTS to go on) */
+#define WHITEHEAT_FLOW_HARD_IN		0x02	/* remote TX is stopped by RTS */
+#define WHITEHEAT_FLOW_SOFT_OUT		0x04	/* TX is stopped by XOFF received (waiting for XON) */
+#define WHITEHEAT_FLOW_SOFT_IN		0x08	/* remote TX is stopped by XOFF transmitted */
+#define WHITEHEAT_FLOW_TX_DONE		0x80	/* TX has completed */
+
 struct whiteheat_status_info {
 	__u8	port;		/* port number (1 to N) */
-	__u8	event;		/* indicates which of the following bytes are the current event */
-	__u8	modem;		/* modem signal status (copy of UART MSR register) */
-	__u8	error;		/* PFO and RX break (copy of UART LSR register) */
-	__u8	flow;		/* flow control state */
-	__u8	connect;	/* connect state, non-zero value indicates connected */
+	__u8	event;		/* indicates what the current event is, see WHITEHEAT_EVENT_* above */
+	__u8	modem;		/* modem signal status (copy of uart's MSR register) */
+	__u8	error;		/* line status (copy of uart's LSR register) */
+	__u8	flow;		/* flow control state, see WHITEHEAT_FLOW_* above */
+	__u8	connect;	/* 0 means not connected, non-zero means connected */
 };
 
-/* data returned from WHITEHEAT_EVENT command */
-struct whiteheat_event {
-	__u8	port;		/* port number (1 to N) */
-	__u8	event;		/* indicates which of the following bytes are the current event */
-	__u8	info;		/* either modem, error, flow, or connect information */
+
+/*
+ * WHITEHEAT_GET_DTR_RTS
+ */
+struct whiteheat_dr_info {
+	__u8	mcr;		/* copy of uart's MCR register */
 };
 
-/* data retured by the WHITEHEAT_GET_HW_INFO command */
+
+/*
+ * WHITEHEAT_GET_HW_INFO
+ */
 struct whiteheat_hw_info {
 	__u8	hw_id;		/* hardware id number, WhiteHEAT = 0 */
 	__u8	sw_major_rev;	/* major version number */
@@ -166,5 +253,30 @@ struct whiteheat_hw_info {
 	} hw_eeprom_info;	/* EEPROM contents */
 };
 
-#endif
 
+/*
+ * WHITEHEAT_EVENT
+ */
+struct whiteheat_event_info {
+	__u8	port;		/* port number (1 to N) */
+	__u8	event;		/* see whiteheat_status_info.event */
+	__u8	info;		/* see whiteheat_status_info.modem, .error, .flow, .connect */
+};
+
+
+/*
+ * WHITEHEAT_DO_TEST
+ */
+#define WHITEHEAT_TEST_FAIL	0x00  /* test failed */
+#define WHITEHEAT_TEST_UNKNOWN	0x01  /* unknown test requested */
+#define WHITEHEAT_TEST_PASS	0xff  /* test passed */
+
+struct whiteheat_test_info {
+	__u8	port;		/* port number (1 to N) */
+	__u8	test;		/* indicates which test this is a response for, see WHITEHEAT_DO_TEST above */
+	__u8	status;		/* see WHITEHEAT_TEST_* above */
+	__u8	results[32];	/* test-dependent results */
+};
+
+
+#endif

drivers/usb/storage/datafab.c

@@ -70,7 +70,7 @@ datafab_bulk_read(struct us_data *us, unsigned char *data, unsigned int len) {
 	unsigned int act_len;	/* ignored */
 
 	if (len == 0)
-		return USB_STOR_TRANSPORT_GOOD;
+		return USB_STOR_XFER_GOOD;
 
 	US_DEBUGP("datafab_bulk_read:  len = %d\n", len);
 	return usb_storage_raw_bulk(us, SCSI_DATA_READ, data, len, &act_len);
@@ -82,7 +82,7 @@ datafab_bulk_write(struct us_data *us, unsigned char *data, unsigned int len) {
 	unsigned int act_len;	/* ignored */
 
 	if (len == 0)
-		return USB_STOR_TRANSPORT_GOOD;
+		return USB_STOR_XFER_GOOD;
 
 	US_DEBUGP("datafab_bulk_write:  len = %d\n", len);
 	return usb_storage_raw_bulk(us, SCSI_DATA_WRITE, data, len, &act_len);
@@ -144,12 +144,12 @@ static int datafab_read_data(struct us_data *us,
 
 		// send the read command
 		result = datafab_bulk_write(us, command, sizeof(command));
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		// read the result
 		result = datafab_bulk_read(us, ptr, len);
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		sectors -= thistime;
@@ -171,7 +171,7 @@ static int datafab_read_data(struct us_data *us,
  leave:
 	if (use_sg)
 		kfree(buffer);
-	return result;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 
@@ -243,17 +243,17 @@ static int datafab_write_data(struct us_data *us,
 
 		// send the command
 		result = datafab_bulk_write(us, command, sizeof(command));
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		// send the data
 		result = datafab_bulk_write(us, ptr, len);
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		// read the result
 		result = datafab_bulk_read(us, reply, sizeof(reply));
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		if (reply[0] != 0x50 && reply[1] != 0) {
@@ -280,7 +280,7 @@ static int datafab_write_data(struct us_data *us,
  leave:
 	if (use_sg)
 		kfree(buffer);
-	return result;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 
@@ -308,11 +308,11 @@ static int datafab_determine_lun(struct us_data *us,
 		command[5] = 0xa0;
 
 		rc = datafab_bulk_write(us, command, 8);
-		if (rc != USB_STOR_TRANSPORT_GOOD) 
-			return rc;
+		if (rc != USB_STOR_XFER_GOOD) 
+			return USB_STOR_TRANSPORT_ERROR;
 
 		rc = datafab_bulk_read(us, buf, sizeof(buf));
-		if (rc == USB_STOR_TRANSPORT_GOOD) {
+		if (rc == USB_STOR_XFER_GOOD) {
 			info->lun = 0;
 			return USB_STOR_TRANSPORT_GOOD;
 		}
@@ -320,11 +320,11 @@ static int datafab_determine_lun(struct us_data *us,
 		command[5] = 0xb0;
 
 		rc = datafab_bulk_write(us, command, 8);
-		if (rc != USB_STOR_TRANSPORT_GOOD) 
-			return rc;
+		if (rc != USB_STOR_XFER_GOOD) 
+			return USB_STOR_TRANSPORT_ERROR;
 
 		rc = datafab_bulk_read(us, buf, sizeof(buf));
-		if (rc == USB_STOR_TRANSPORT_GOOD) {
+		if (rc == USB_STOR_XFER_GOOD) {
 			info->lun = 1;
 			return USB_STOR_TRANSPORT_GOOD;
 		}
@@ -332,7 +332,7 @@ static int datafab_determine_lun(struct us_data *us,
 		wait_ms(20);
 	}
 
-	return USB_STOR_TRANSPORT_FAILED;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 static int datafab_id_device(struct us_data *us,
@@ -358,22 +358,23 @@ static int datafab_id_device(struct us_data *us,
 	command[5] += (info->lun << 4);
 
 	rc = datafab_bulk_write(us, command, 8);
-	if (rc != USB_STOR_TRANSPORT_GOOD) 
-		return rc;
+	if (rc != USB_STOR_XFER_GOOD) 
+		return USB_STOR_TRANSPORT_ERROR;
 
 	// we'll go ahead and extract the media capacity while we're here...
 	//
 	rc = datafab_bulk_read(us, reply, sizeof(reply));
-	if (rc == USB_STOR_TRANSPORT_GOOD) {
+	if (rc == USB_STOR_XFER_GOOD) {
 		// capacity is at word offset 57-58
 		//
 		info->sectors = ((u32)(reply[117]) << 24) | 
 				((u32)(reply[116]) << 16) |
 				((u32)(reply[115]) <<  8) | 
 				((u32)(reply[114])      );
+		return USB_STOR_TRANSPORT_GOOD;
 	}
 		
-	return rc;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 

drivers/usb/storage/freecom.c

@@ -197,7 +197,7 @@ freecom_readdata (Scsi_Cmnd *srb, struct us_data *us,
 		/* has the current command been aborted? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("freecom_readdata(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
                 return USB_STOR_TRANSPORT_ERROR;
@@ -238,7 +238,7 @@ freecom_writedata (Scsi_Cmnd *srb, struct us_data *us,
 		/* has the current command been aborted? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("freecom_writedata(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
                 return USB_STOR_TRANSPORT_ERROR;
@@ -301,7 +301,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* we canceled this transfer */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("freecom_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
                 return USB_STOR_TRANSPORT_ERROR;
@@ -316,7 +316,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* we canceled this transfer */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("freecom_transport(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_TRANSPORT_ABORTED;
 	}
 
         US_DEBUG(pdump ((void *) fst, partial));
@@ -354,7 +354,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 			/* we canceled this transfer */
 			if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 				US_DEBUGP("freecom_transport(): transfer aborted\n");
-				return US_BULK_TRANSFER_ABORTED;
+				return USB_STOR_TRANSPORT_ABORTED;
 			}
 
 			return USB_STOR_TRANSPORT_ERROR;
@@ -369,7 +369,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* we canceled this transfer */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("freecom_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
 		US_DEBUG(pdump ((void *) fst, partial));
@@ -430,7 +430,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
                         US_DEBUGP ("freecom_transport: transfer aborted\n");
-                        return US_BULK_TRANSFER_ABORTED;
+                        return USB_STOR_TRANSPORT_ABORTED;
                 }
                 if (partial != 4 || result != 0)
                         return USB_STOR_TRANSPORT_ERROR;
@@ -459,7 +459,7 @@ int freecom_transport(Scsi_Cmnd *srb, struct us_data *us)
 
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
                         US_DEBUGP ("freecom_transport: transfer aborted\n");
-                        return US_BULK_TRANSFER_ABORTED;
+                        return USB_STOR_TRANSPORT_ABORTED;
                 }
                 if (partial != 4 || result != 0)
                         return USB_STOR_TRANSPORT_ERROR;

drivers/usb/storage/jumpshot.c

@@ -65,7 +65,7 @@ static inline int jumpshot_bulk_read(struct us_data *us,
 	unsigned int act_len;	/* ignored */
 
 	if (len == 0)
-		return USB_STOR_TRANSPORT_GOOD;
+		return USB_STOR_XFER_GOOD;
 
 	US_DEBUGP("jumpshot_bulk_read:  len = %d\n", len);
 	return usb_storage_raw_bulk(us, SCSI_DATA_READ, data, len, &act_len);
@@ -79,7 +79,7 @@ static inline int jumpshot_bulk_write(struct us_data *us,
 	unsigned int act_len;	/* ignored */
 
 	if (len == 0)
-		return USB_STOR_TRANSPORT_GOOD;
+		return USB_STOR_XFER_GOOD;
 
 	US_DEBUGP("jumpshot_bulk_write:  len = %d\n", len);
 	return usb_storage_raw_bulk(us, SCSI_DATA_WRITE, data, len, &act_len);
@@ -168,7 +168,7 @@ static int jumpshot_read_data(struct us_data *us,
 
 		// read the result
 		result = jumpshot_bulk_read(us, ptr, len);
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		US_DEBUGP("jumpshot_read_data:  %d bytes\n", len);
@@ -192,7 +192,7 @@ static int jumpshot_read_data(struct us_data *us,
  leave:
 	if (use_sg)
 		kfree(buffer);
-	return result;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 
@@ -253,7 +253,7 @@ static int jumpshot_write_data(struct us_data *us,
 
 		// send the data
 		result = jumpshot_bulk_write(us, ptr, len);
-		if (result != USB_STOR_TRANSPORT_GOOD)
+		if (result != USB_STOR_XFER_GOOD)
 			goto leave;
 
 		// read the result.  apparently the bulk write can complete
@@ -288,7 +288,7 @@ static int jumpshot_write_data(struct us_data *us,
  leave:
 	if (use_sg)
 		kfree(buffer);
-	return result;
+	return USB_STOR_TRANSPORT_ERROR;
 }
 
 static int jumpshot_id_device(struct us_data *us,
@@ -314,8 +314,8 @@ static int jumpshot_id_device(struct us_data *us,
 
 	// read the reply
 	rc = jumpshot_bulk_read(us, reply, sizeof(reply));
-	if (rc != USB_STOR_TRANSPORT_GOOD)
-		return rc;
+	if (rc != USB_STOR_XFER_GOOD)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	info->sectors = ((u32)(reply[117]) << 24) |
 			((u32)(reply[116]) << 16) |

drivers/usb/storage/raw_bulk.c

@@ -61,7 +61,7 @@ usb_storage_send_control(struct us_data *us,
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_stor_send_control(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_TRANSPORT_ABORTED;
 	}
 
 	// Check the return code for the command.
@@ -70,7 +70,7 @@ usb_storage_send_control(struct us_data *us,
 		/* a stall indicates a protocol error */
 		if (result == -EPIPE) {
 			US_DEBUGP("-- Stall on control pipe\n");
-			return USB_STOR_TRANSPORT_FAILED;
+			return USB_STOR_TRANSPORT_ERROR;
 		}
 
 		/* Uh oh... serious problem here */
@@ -100,14 +100,14 @@ usb_storage_raw_bulk(struct us_data *us, int direction, unsigned char *data,
 			  " pipe 0x%x, stalled at %d bytes\n",
 			  pipe, *act_len);
 		if (usb_stor_clear_halt(us, pipe) < 0)
-			return US_BULK_TRANSFER_FAILED;
-		/* return US_BULK_TRANSFER_SHORT; */
+			return USB_STOR_XFER_ERROR;
+		return USB_STOR_XFER_STALLED;
 	}
 
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_storage_raw_bulk(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_XFER_ABORTED;
 	}
 
 	if (result) {
@@ -122,13 +122,13 @@ usb_storage_raw_bulk(struct us_data *us, int direction, unsigned char *data,
 			US_DEBUGP("raw_bulk(): unknown error %d\n",
 				  result);
 
-		return US_BULK_TRANSFER_FAILED;
+		return USB_STOR_XFER_ERROR;
 	}
 
 	if (*act_len != len) {
 		US_DEBUGP("Warning: Transferred only %d of %d bytes\n",
 			  *act_len, len);
-		return US_BULK_TRANSFER_SHORT;
+		return USB_STOR_XFER_SHORT;
 	}
 
 #if 0
@@ -137,7 +137,7 @@ usb_storage_raw_bulk(struct us_data *us, int direction, unsigned char *data,
 		  *act_len, len);
 #endif
 
-	return US_BULK_TRANSFER_GOOD;
+	return USB_STOR_XFER_GOOD;
 }
 
 int
@@ -145,14 +145,14 @@ usb_storage_bulk_transport(struct us_data *us, int direction,
 			   unsigned char *data, unsigned int len,
 			   int use_sg) {
 
-	int result = USB_STOR_TRANSPORT_GOOD;
+	int result = USB_STOR_XFER_ERROR;
 	int transferred = 0;
 	int i;
 	struct scatterlist *sg;
 	unsigned int act_len;
 
 	if (len == 0)
-		return USB_STOR_TRANSPORT_GOOD;
+		return USB_STOR_XFER_GOOD;
 
 #if DEBUG_PRCT
 
@@ -196,7 +196,7 @@ usb_storage_bulk_transport(struct us_data *us, int direction,
 
 			result = usb_storage_raw_bulk(us, direction,
 						      buf, length, &act_len);
-			if (result != US_BULK_TRANSFER_GOOD)
+			if (result != USB_STOR_XFER_GOOD)
 				break;
 			transferred += length;
 		}

drivers/usb/storage/sddr09.c

@@ -285,12 +285,14 @@ sddr09_request_sense(struct us_data *us, unsigned char *sensebuf, int buflen) {
 	}
 
 	result = usb_storage_raw_bulk(us, SCSI_DATA_READ, sensebuf, buflen, &act_len);
-	if (result != USB_STOR_TRANSPORT_GOOD)
+	if (result != USB_STOR_XFER_GOOD) {
 		US_DEBUGP("request sense bulk in failed\n");
-	else
+		return USB_STOR_TRANSPORT_ERROR;
+	}
+	else {
 		US_DEBUGP("request sense worked\n");
-
-	return result;
+		return USB_STOR_TRANSPORT_GOOD;
+	}
 }
 
 /*
@@ -344,11 +346,12 @@ sddr09_readX(struct us_data *us, int x, unsigned long fromaddress,
 	result = usb_storage_bulk_transport(us, SCSI_DATA_READ,
 				       buf, bulklen, use_sg);
 
-	if (result != USB_STOR_TRANSPORT_GOOD)
+	if (result != USB_STOR_XFER_GOOD) {
 		US_DEBUGP("Result for bulk_transport in sddr09_read2%d %d\n",
 			  x, result);
-
-	return result;
+		return USB_STOR_TRANSPORT_ERROR;
+	}
+	return USB_STOR_TRANSPORT_GOOD;
 }
 
 /*
@@ -510,11 +513,12 @@ sddr09_writeX(struct us_data *us,
 	result = usb_storage_bulk_transport(us, SCSI_DATA_WRITE,
 				       buf, bulklen, use_sg);
 
-	if (result != USB_STOR_TRANSPORT_GOOD)
+	if (result != USB_STOR_XFER_GOOD) {
 		US_DEBUGP("Result for bulk_transport in sddr09_writeX %d\n",
 			  result);
-
-	return result;
+		return USB_STOR_TRANSPORT_ERROR;
+	}
+	return USB_STOR_TRANSPORT_GOOD;
 }
 
 /* erase address, write same address */
@@ -590,13 +594,14 @@ sddr09_read_sg_test_only(struct us_data *us) {
 
 	result = usb_storage_bulk_transport(us, SCSI_DATA_READ,
 				       buf, bulklen, 0);
-	if (result != USB_STOR_TRANSPORT_GOOD)
+	kfree(buf);
+	if (result != USB_STOR_XFER_GOOD) {
 		US_DEBUGP("Result for bulk_transport in sddr09_read_sg %d\n",
 			  result);
+		return USB_STOR_TRANSPORT_ERROR;
+	}
 
-	kfree(buf);
-
-	return result;
+	return USB_STOR_TRANSPORT_GOOD;
 }
 #endif
 
@@ -629,7 +634,8 @@ sddr09_read_status(struct us_data *us, unsigned char *status) {
 	result = usb_storage_bulk_transport(us, SCSI_DATA_READ,
 				       data, sizeof(data), 0);
 	*status = data[0];
-	return result;
+	return (result == USB_STOR_XFER_GOOD ?
+			USB_STOR_TRANSPORT_GOOD : USB_STOR_TRANSPORT_ERROR);
 }
 
 static int
@@ -953,7 +959,8 @@ sddr09_read_deviceID(struct us_data *us, unsigned char *deviceID) {
 	for (i = 0; i < 4; i++)
 		deviceID[i] = content[i];
 
-	return result;
+	return (result == USB_STOR_XFER_GOOD ?
+			USB_STOR_TRANSPORT_GOOD : USB_STOR_TRANSPORT_ERROR);
 }
 
 static int
@@ -1549,7 +1556,8 @@ int sddr09_transport(Scsi_Cmnd *srb, struct us_data *us)
 					       srb->request_bufflen,
 					       srb->use_sg);
 
-		return result;
+		return (result == USB_STOR_XFER_GOOD ?
+			USB_STOR_TRANSPORT_GOOD : USB_STOR_TRANSPORT_ERROR);
 	} 
 
 	return USB_STOR_TRANSPORT_GOOD;

drivers/usb/storage/sddr55.c

@@ -101,16 +101,16 @@ static int sddr55_status(struct us_data *us)
 	US_DEBUGP("Result for send_command in status %d\n",
 		result);
 
-	if (result != US_BULK_TRANSFER_GOOD) {
+	if (result != USB_STOR_XFER_GOOD) {
 		set_sense_info (4, 0, 0);	/* hardware error */
-		return result;
+		return USB_STOR_TRANSPORT_ERROR;
 	}
 
 	result = sddr55_bulk_transport(us,
 		SCSI_DATA_READ, status,	4);
 
 	/* expect to get short transfer if no card fitted */
-	if (result == US_BULK_TRANSFER_SHORT) {
+	if (result == USB_STOR_XFER_SHORT || result == USB_STOR_XFER_STALLED) {
 		/* had a short transfer, no card inserted, free map memory */
 		if (info->lba_to_pba)
 			kfree(info->lba_to_pba);
@@ -123,12 +123,12 @@ static int sddr55_status(struct us_data *us)
 		info->force_read_only = 0;
 
 		set_sense_info (2, 0x3a, 0);	/* not ready, medium not present */
-		return result;
+		return USB_STOR_TRANSPORT_FAILED;
 	}
 
-	if (result != US_BULK_TRANSFER_GOOD) {
+	if (result != USB_STOR_XFER_GOOD) {
 		set_sense_info (4, 0, 0);	/* hardware error */
-		return result;
+		return USB_STOR_TRANSPORT_FAILED;
 	}
 	
 	/* check write protect status */
@@ -138,11 +138,12 @@ static int sddr55_status(struct us_data *us)
 	result = sddr55_bulk_transport(us,
 		SCSI_DATA_READ, status,	2);
 
-	if (result != US_BULK_TRANSFER_GOOD) {
+	if (result != USB_STOR_XFER_GOOD) {
 		set_sense_info (4, 0, 0);	/* hardware error */
 	}
 
-	return result;
+	return (result == USB_STOR_XFER_GOOD ?
+			USB_STOR_TRANSPORT_GOOD : USB_STOR_TRANSPORT_FAILED);
 }
 
 
@@ -214,23 +215,29 @@ static int sddr55_read_data(struct us_data *us,
 			US_DEBUGP("Result for send_command in read_data %d\n",
 				result);
 
-			if (result != US_BULK_TRANSFER_GOOD)
+			if (result != USB_STOR_XFER_GOOD) {
+				result = USB_STOR_TRANSPORT_ERROR;
 				goto leave;
+			}
 
 			/* read data */
 			result = sddr55_bulk_transport(us,
 				SCSI_DATA_READ, ptr,
 				pages<<info->pageshift);
 
-			if (result != US_BULK_TRANSFER_GOOD)
+			if (result != USB_STOR_XFER_GOOD) {
+				result = USB_STOR_TRANSPORT_ERROR;
 				goto leave;
+			}
 
 			/* now read status */
 			result = sddr55_bulk_transport(us,
 				SCSI_DATA_READ, status, 2);
 
-			if (result != US_BULK_TRANSFER_GOOD)
+			if (result != USB_STOR_XFER_GOOD) {
+				result = USB_STOR_TRANSPORT_ERROR;
 				goto leave;
+			}
 
 			/* check status for error */
 			if (status[0] == 0xff && status[1] == 0x4) {
@@ -247,6 +254,7 @@ static int sddr55_read_data(struct us_data *us,
 	}
 
 	us_copy_to_sgbuf_all(buffer, len, content, use_sg);
+	result = USB_STOR_TRANSPORT_GOOD;
 
 leave:
 	if (use_sg)
@@ -374,12 +382,13 @@ static int sddr55_write_data(struct us_data *us,
 		result = sddr55_bulk_transport(us,
 			SCSI_DATA_WRITE, command, 8);
 
-		if (result != US_BULK_TRANSFER_GOOD) {
+		if (result != USB_STOR_XFER_GOOD) {
 			US_DEBUGP("Result for send_command in write_data %d\n",
 			result);
 
 			/* set_sense_info is superfluous here? */
 			set_sense_info (3, 0x3, 0);/* peripheral write error */
+			result = USB_STOR_TRANSPORT_FAILED;
 			goto leave;
 		}
 
@@ -388,24 +397,26 @@ static int sddr55_write_data(struct us_data *us,
 			SCSI_DATA_WRITE, ptr,
 			pages<<info->pageshift);
 
-		if (result != US_BULK_TRANSFER_GOOD) {
+		if (result != USB_STOR_XFER_GOOD) {
 			US_DEBUGP("Result for send_data in write_data %d\n",
 				  result);
 
 			/* set_sense_info is superfluous here? */
 			set_sense_info (3, 0x3, 0);/* peripheral write error */
+			result = USB_STOR_TRANSPORT_FAILED;
 			goto leave;
 		}
 
 		/* now read status */
 		result = sddr55_bulk_transport(us, SCSI_DATA_READ, status, 6);
 
-		if (result != US_BULK_TRANSFER_GOOD) {
+		if (result != USB_STOR_XFER_GOOD) {
 			US_DEBUGP("Result for get_status in write_data %d\n",
 				  result);
 
 			/* set_sense_info is superfluous here? */
 			set_sense_info (3, 0x3, 0);/* peripheral write error */
+			result = USB_STOR_TRANSPORT_FAILED;
 			goto leave;
 		}
 
@@ -446,6 +457,7 @@ static int sddr55_write_data(struct us_data *us,
 		sectors -= pages >> info->smallpageshift;
 		ptr += (pages << info->pageshift);
 	}
+	result = USB_STOR_TRANSPORT_GOOD;
 
  leave:
 	if (use_sg)
@@ -468,14 +480,14 @@ static int sddr55_read_deviceID(struct us_data *us,
 	US_DEBUGP("Result of send_control for device ID is %d\n",
 		result);
 
-	if (result != US_BULK_TRANSFER_GOOD)
-		return result;
+	if (result != USB_STOR_XFER_GOOD)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	result = sddr55_bulk_transport(us,
 		SCSI_DATA_READ, content, 4);
 
-	if (result != US_BULK_TRANSFER_GOOD)
-		return result;
+	if (result != USB_STOR_XFER_GOOD)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	*manufacturerID = content[0];
 	*deviceID = content[1];
@@ -485,7 +497,7 @@ static int sddr55_read_deviceID(struct us_data *us,
 			SCSI_DATA_READ, content, 2);
 	}
 
-	return result;
+	return USB_STOR_TRANSPORT_GOOD;
 }
 
 
@@ -510,7 +522,7 @@ static unsigned long sddr55_get_capacity(struct us_data *us) {
 	US_DEBUGP("Result of read_deviceID is %d\n",
 		result);
 
-	if (result != US_BULK_TRANSFER_GOOD)
+	if (result != USB_STOR_XFER_GOOD)
 		return 0;
 
 	US_DEBUGP("Device ID = %02X\n", deviceID);
@@ -603,21 +615,21 @@ static int sddr55_read_map(struct us_data *us) {
 
 	result = sddr55_bulk_transport(us, SCSI_DATA_WRITE, command, 8);
 
-	if ( result != US_BULK_TRANSFER_GOOD) {
+	if ( result != USB_STOR_XFER_GOOD) {
 		kfree (buffer);
 		return -1;
 	}
 
 	result = sddr55_bulk_transport(us, SCSI_DATA_READ, buffer, numblocks * 2);
 
-	if ( result != US_BULK_TRANSFER_GOOD) {
+	if ( result != USB_STOR_XFER_GOOD) {
 		kfree (buffer);
 		return -1;
 	}
 
 	result = sddr55_bulk_transport(us, SCSI_DATA_READ, command, 2);
 
-	if ( result != US_BULK_TRANSFER_GOOD) {
+	if ( result != USB_STOR_XFER_GOOD) {
 		kfree (buffer);
 		return -1;
 	}

drivers/usb/storage/shuttle_usbat.c

@@ -153,7 +153,8 @@ int usbat_read_block(struct us_data *us,
 
 	result = usb_storage_bulk_transport(us, SCSI_DATA_READ, content, len, use_sg);
 
-	return result;
+	return (result == USB_STOR_XFER_GOOD ?
+			USB_STOR_TRANSPORT_GOOD : USB_STOR_TRANSPORT_ERROR);
 }
 
 /*
@@ -234,8 +235,8 @@ int usbat_write_block(struct us_data *us,
 
 	result = usb_storage_bulk_transport(us, SCSI_DATA_WRITE, content, len, use_sg);
 
-	if (result != USB_STOR_TRANSPORT_GOOD)
-		return result;
+	if (result != USB_STOR_XFER_GOOD)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	return usbat_wait_not_busy(us, minutes);
 }
@@ -309,8 +310,8 @@ int usbat_rw_block_test(struct us_data *us,
 				SCSI_DATA_WRITE, 
 				data, num_registers*2, 0);
 
-			if (result!=USB_STOR_TRANSPORT_GOOD)
-				return result;
+			if (result!=USB_STOR_XFER_GOOD)
+				return USB_STOR_TRANSPORT_ERROR;
 
 		}
 
@@ -341,7 +342,8 @@ int usbat_rw_block_test(struct us_data *us,
 		 * transferred.
 		 */
 
-		if (result == US_BULK_TRANSFER_SHORT) {
+		if (result == USB_STOR_XFER_SHORT ||
+				result == USB_STOR_XFER_STALLED) {
 
 			/*
 			 * If we're reading and we stalled, then clear
@@ -373,8 +375,8 @@ int usbat_rw_block_test(struct us_data *us,
 			US_DEBUGP("Redoing %s\n",
 			  direction==SCSI_DATA_WRITE ? "write" : "read");
 
-		} else if (result != US_BULK_TRANSFER_GOOD)
-			return result;
+		} else if (result != USB_STOR_XFER_GOOD)
+			return USB_STOR_TRANSPORT_ERROR;
 		else
 			return usbat_wait_not_busy(us, minutes);
 
@@ -425,8 +427,8 @@ int usbat_multiple_write(struct us_data *us,
 	result = usb_storage_bulk_transport(us,
 		SCSI_DATA_WRITE, data, num_registers*2, 0);
 
-	if (result != USB_STOR_TRANSPORT_GOOD)
-		return result;
+	if (result != USB_STOR_XFER_GOOD)
+		return USB_STOR_TRANSPORT_ERROR;
 
 	return usbat_wait_not_busy(us, 0);
 }

drivers/usb/storage/transport.c

@@ -572,36 +572,37 @@ int usb_stor_transfer_partial(struct us_data *us, char *buf, int length)
 	if (result == -EPIPE) {
 		US_DEBUGP("clearing endpoint halt for pipe 0x%x\n", pipe);
 		if (usb_stor_clear_halt(us, pipe) < 0)
-			return US_BULK_TRANSFER_FAILED;
+			return USB_STOR_XFER_ERROR;
+		return USB_STOR_XFER_STALLED;
 	}
 
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_stor_transfer_partial(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
-	}
-
-	/* did we send all the data? */
-	if (partial == length) {
-		US_DEBUGP("usb_stor_transfer_partial(): transfer complete\n");
-		return US_BULK_TRANSFER_GOOD;
+		return USB_STOR_XFER_ABORTED;
 	}
 
 	/* NAK - that means we've retried a few times already */
 	if (result == -ETIMEDOUT) {
 		US_DEBUGP("usb_stor_transfer_partial(): device NAKed\n");
-		return US_BULK_TRANSFER_FAILED;
+		return USB_STOR_XFER_ERROR;
 	}
 
 	/* the catch-all error case */
 	if (result) {
 		US_DEBUGP("usb_stor_transfer_partial(): unknown error\n");
-		return US_BULK_TRANSFER_FAILED;
+		return USB_STOR_XFER_ERROR;
+	}
+
+	/* did we send all the data? */
+	if (partial == length) {
+		US_DEBUGP("usb_stor_transfer_partial(): transfer complete\n");
+		return USB_STOR_XFER_GOOD;
 	}
 
 	/* no error code, so we must have transferred some data, 
 	 * just not all of it */
-	return US_BULK_TRANSFER_SHORT;
+	return USB_STOR_XFER_SHORT;
 }
 
 /*
@@ -739,7 +740,7 @@ void usb_stor_invoke_transport(Scsi_Cmnd *srb, struct us_data *us)
 	 * Also, if we have a short transfer on a command that can't have
 	 * a short transfer, we're going to do this.
 	 */
-	if ((srb->result == US_BULK_TRANSFER_SHORT) &&
+	if ((srb->result == USB_STOR_XFER_SHORT) &&
 	    !((srb->cmnd[0] == REQUEST_SENSE) ||
 	      (srb->cmnd[0] == INQUIRY) ||
 	      (srb->cmnd[0] == MODE_SENSE) ||
@@ -995,13 +996,13 @@ int usb_stor_CBI_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_stor_control_msg(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_TRANSPORT_ABORTED;
 	}
 
 	/* a stall indicates a protocol error */
 	if (result == -EPIPE) {
 		US_DEBUGP("-- Stall on control pipe\n");
-		return USB_STOR_TRANSPORT_FAILED;
+		return USB_STOR_TRANSPORT_ERROR;
 	}
 
 	if (result < 0) {
@@ -1017,13 +1018,13 @@ int usb_stor_CBI_transport(Scsi_Cmnd *srb, struct us_data *us)
 		US_DEBUGP("CBI data stage result is 0x%x\n", result);
 
 		/* report any errors */
-		if (result == US_BULK_TRANSFER_ABORTED) {
+		if (result == USB_STOR_XFER_ABORTED) {
 			clear_bit(US_FLIDX_IP_WANTED, &us->flags);
 			return USB_STOR_TRANSPORT_ABORTED;
 		}
-		if (result == US_BULK_TRANSFER_FAILED) {
+		if (result == USB_STOR_XFER_ERROR) {
 			clear_bit(US_FLIDX_IP_WANTED, &us->flags);
-			return USB_STOR_TRANSPORT_FAILED;
+			return USB_STOR_TRANSPORT_ERROR;
 		}
 	}
 
@@ -1103,13 +1104,13 @@ int usb_stor_CB_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* did we abort this command? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("usb_stor_CB_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
 		/* a stall indicates a protocol error */
 		if (result == -EPIPE) {
 			US_DEBUGP("-- Stall on control pipe\n");
-			return USB_STOR_TRANSPORT_FAILED;
+			return USB_STOR_TRANSPORT_ERROR;
 		}
 
 		/* Uh oh... serious problem here */
@@ -1124,11 +1125,11 @@ int usb_stor_CB_transport(Scsi_Cmnd *srb, struct us_data *us)
 		US_DEBUGP("CB data stage result is 0x%x\n", result);
 
 		/* report any errors */
-		if (result == US_BULK_TRANSFER_ABORTED) {
+		if (result == USB_STOR_XFER_ABORTED) {
 			return USB_STOR_TRANSPORT_ABORTED;
 		}
-		if (result == US_BULK_TRANSFER_FAILED) {
-			return USB_STOR_TRANSPORT_FAILED;
+		if (result == USB_STOR_XFER_ERROR) {
+			return USB_STOR_TRANSPORT_ERROR;
 		}
 	}
 
@@ -1207,7 +1208,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_TRANSPORT_ABORTED;
 	}
 
 	/* if we stall, we need to clear it before we go on */
@@ -1218,7 +1219,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* did we abort this command? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 		if (result < 0)
 			return USB_STOR_TRANSPORT_ERROR;
@@ -1237,7 +1238,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 			US_DEBUGP("Bulk data transfer result 0x%x\n", result);
 
 			/* if it was aborted, we need to indicate that */
-			if (result == US_BULK_TRANSFER_ABORTED)
+			if (result == USB_STOR_XFER_ABORTED)
 				return USB_STOR_TRANSPORT_ABORTED;
 		}
 	}
@@ -1257,7 +1258,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 	/* did we abort this command? */
 	if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 		US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-		return US_BULK_TRANSFER_ABORTED;
+		return USB_STOR_TRANSPORT_ABORTED;
 	}
 
 	/* did the attempt to read the CSW fail? */
@@ -1268,7 +1269,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* did we abort this command? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 		if (result < 0)
 			return USB_STOR_TRANSPORT_ERROR;
@@ -1281,7 +1282,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 		/* did we abort this command? */
 		if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 			US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-			return US_BULK_TRANSFER_ABORTED;
+			return USB_STOR_TRANSPORT_ABORTED;
 		}
 
 		/* if it fails again, we need a reset and return an error*/
@@ -1292,7 +1293,7 @@ int usb_stor_Bulk_transport(Scsi_Cmnd *srb, struct us_data *us)
 			/* did we abort this command? */
 			if (atomic_read(&us->sm_state) == US_STATE_ABORTING) {
 				US_DEBUGP("usb_stor_Bulk_transport(): transfer aborted\n");
-				return US_BULK_TRANSFER_ABORTED;
+				return USB_STOR_TRANSPORT_ABORTED;
 			}
 			return USB_STOR_TRANSPORT_ERROR;
 		}

drivers/usb/storage/transport.h

@@ -115,12 +115,13 @@ struct bulk_cs_wrap {
 #define US_BULK_GET_MAX_LUN	0xfe
 
 /*
- * usb_stor_transfer() return codes
+ * usb_stor_transfer() return codes, in order of severity
  */
-#define US_BULK_TRANSFER_GOOD		0  /* good transfer                 */
-#define US_BULK_TRANSFER_SHORT		1  /* transfered less than expected */
-#define US_BULK_TRANSFER_FAILED		2  /* transfer died in the middle   */
-#define US_BULK_TRANSFER_ABORTED	3  /* transfer canceled             */
+#define USB_STOR_XFER_GOOD		0  /* good transfer                 */
+#define USB_STOR_XFER_SHORT		1  /* transfered less than expected */
+#define USB_STOR_XFER_STALLED		2  /* endpoint stalled		    */
+#define USB_STOR_XFER_ERROR		3  /* transfer died in the middle   */
+#define USB_STOR_XFER_ABORTED		4  /* transfer canceled             */
 
 /*
  * Transport return codes