Commit 829ae273 authored by Linus Torvalds's avatar Linus Torvalds

Merge branch 'omap-for-linus' of...

Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (33 commits)
  OMAP3: PM: Boot message is not an error, and not helpful, remove it
  OMAP3: cpuidle: change the power domains modes determination logic
  OMAP3: cpuidle: code rework for improved readability
  OMAP3: cpuidle: re-organize the C-states data
  OMAP3: clean-up mach specific cpuidle data structures
  OMAP3 cpuidle: remove useless SDP specific timings
  usb: otg: OMAP4430: Powerdown the internal PHY when USB is disabled
  usb: otg: OMAP4430: Fixing the omap4430_phy_init function
  usb: musb: am35x: fix compile error when building am35x
  usb: musb: OMAP4430: Power down the PHY during board init
  omap: drop board-igep0030.c
  omap: igep0020: add support for IGEP3
  omap: igep0020: minor refactoring
  omap: igep0020: name refactoring for future merge with IGEP3
  omap: Remove support for omap2evm
  arm: omap2plus: GPIO cleanup
  omap: musb: introduce default board config
  omap: move detection of NAND CS to common-board-devices
  omap: use common initialization for PMIC i2c bus
  omap: consolidate touch screen initialization among different boards
  ...
parents 6ddb4518 9b28b11e
......@@ -21,58 +21,22 @@ CONFIG_MODVERSIONS=y
CONFIG_MODULE_SRCVERSION_ALL=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_ARCH_OMAP=y
CONFIG_ARCH_OMAP2=y
CONFIG_ARCH_OMAP3=y
CONFIG_ARCH_OMAP4=y
CONFIG_OMAP_RESET_CLOCKS=y
CONFIG_OMAP_MUX_DEBUG=y
CONFIG_OMAP_32K_TIMER=y
CONFIG_MACH_OMAP_GENERIC=y
CONFIG_ARCH_OMAP2420=y
CONFIG_ARCH_OMAP2430=y
CONFIG_ARCH_OMAP3430=y
CONFIG_MACH_OMAP_H4=y
CONFIG_MACH_OMAP_APOLLON=y
CONFIG_MACH_OMAP_2430SDP=y
CONFIG_MACH_OMAP3_BEAGLE=y
CONFIG_MACH_DEVKIT8000=y
CONFIG_MACH_OMAP_LDP=y
CONFIG_MACH_OVERO=y
CONFIG_MACH_OMAP3EVM=y
CONFIG_MACH_OMAP3517EVM=y
CONFIG_MACH_OMAP3_PANDORA=y
CONFIG_MACH_OMAP3_TOUCHBOOK=y
CONFIG_MACH_OMAP_3430SDP=y
CONFIG_MACH_NOKIA_N8X0=y
CONFIG_MACH_NOKIA_RX51=y
CONFIG_MACH_OMAP_ZOOM2=y
CONFIG_MACH_OMAP_ZOOM3=y
CONFIG_MACH_CM_T35=y
CONFIG_MACH_IGEP0020=y
CONFIG_MACH_SBC3530=y
CONFIG_MACH_OMAP_3630SDP=y
CONFIG_MACH_OMAP_4430SDP=y
CONFIG_ARM_THUMBEE=y
CONFIG_ARM_L1_CACHE_SHIFT=5
CONFIG_ARM_ERRATA_411920=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_SMP=y
CONFIG_NR_CPUS=2
# CONFIG_LOCAL_TIMERS is not set
CONFIG_AEABI=y
CONFIG_LEDS=y
CONFIG_ZBOOT_ROM_TEXT=0x0
CONFIG_ZBOOT_ROM_BSS=0x0
CONFIG_CMDLINE="root=/dev/mmcblk0p2 rootwait console=ttyO2,115200"
CONFIG_KEXEC=y
CONFIG_FPE_NWFPE=y
CONFIG_VFP=y
CONFIG_NEON=y
CONFIG_BINFMT_MISC=y
CONFIG_PM=y
CONFIG_PM_DEBUG=y
CONFIG_PM_RUNTIME=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
......@@ -89,14 +53,6 @@ CONFIG_IP_PNP_RARP=y
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
CONFIG_BT=m
CONFIG_BT_L2CAP=m
CONFIG_BT_SCO=m
CONFIG_BT_RFCOMM=y
CONFIG_BT_RFCOMM_TTY=y
CONFIG_BT_BNEP=m
CONFIG_BT_BNEP_MC_FILTER=y
CONFIG_BT_BNEP_PROTO_FILTER=y
CONFIG_BT_HIDP=m
CONFIG_BT_HCIUART=m
CONFIG_BT_HCIUART_H4=y
CONFIG_BT_HCIUART_BCSP=y
......@@ -107,11 +63,9 @@ CONFIG_CFG80211=m
CONFIG_MAC80211=m
CONFIG_MAC80211_RC_PID=y
CONFIG_MAC80211_RC_DEFAULT_PID=y
CONFIG_MAC80211_LEDS=y
CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
CONFIG_CONNECTOR=y
CONFIG_MTD=y
CONFIG_MTD_CONCAT=y
CONFIG_MTD_CMDLINE_PARTS=y
CONFIG_MTD_CHAR=y
CONFIG_MTD_BLOCK=y
......@@ -127,7 +81,6 @@ CONFIG_MTD_UBI=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=16384
CONFIG_EEPROM_LEGACY=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_SCSI_MULTI_LUN=y
......@@ -158,19 +111,15 @@ CONFIG_TOUCHSCREEN_ADS7846=y
CONFIG_INPUT_MISC=y
CONFIG_INPUT_TWL4030_PWRBUTTON=y
CONFIG_VT_HW_CONSOLE_BINDING=y
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_SERIAL_8250_NR_UARTS=32
CONFIG_SERIAL_8250_EXTENDED=y
CONFIG_SERIAL_8250_MANY_PORTS=y
CONFIG_SERIAL_8250_SHARE_IRQ=y
CONFIG_SERIAL_8250_DETECT_IRQ=y
CONFIG_SERIAL_8250_RSA=y
# CONFIG_LEGACY_PTYS is not set
CONFIG_HW_RANDOM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_OMAP=y
CONFIG_SPI=y
CONFIG_SPI_OMAP24XX=y
CONFIG_DEBUG_GPIO=y
......@@ -181,10 +130,6 @@ CONFIG_POWER_SUPPLY=y
CONFIG_WATCHDOG=y
CONFIG_OMAP_WATCHDOG=y
CONFIG_TWL4030_WATCHDOG=y
CONFIG_MENELAUS=y
CONFIG_TWL4030_CORE=y
CONFIG_TWL4030_POWER=y
CONFIG_REGULATOR=y
CONFIG_REGULATOR_TWL4030=y
CONFIG_REGULATOR_TPS65023=y
CONFIG_REGULATOR_TPS6507X=y
......@@ -208,7 +153,6 @@ CONFIG_BACKLIGHT_LCD_SUPPORT=y
CONFIG_LCD_CLASS_DEVICE=y
CONFIG_LCD_PLATFORM=y
CONFIG_DISPLAY_SUPPORT=y
# CONFIG_VGA_CONSOLE is not set
CONFIG_FRAMEBUFFER_CONSOLE=y
CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
CONFIG_FONTS=y
......@@ -217,25 +161,20 @@ CONFIG_FONT_8x16=y
CONFIG_LOGO=y
CONFIG_SOUND=m
CONFIG_SND=m
CONFIG_SND_MIXER_OSS=y
CONFIG_SND_PCM_OSS=y
CONFIG_SND_MIXER_OSS=m
CONFIG_SND_PCM_OSS=m
CONFIG_SND_VERBOSE_PRINTK=y
CONFIG_SND_DEBUG=y
CONFIG_SND_USB_AUDIO=y
CONFIG_SND_SOC=y
CONFIG_SND_OMAP_SOC=y
CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=y
CONFIG_SND_USB_AUDIO=m
CONFIG_SND_SOC=m
CONFIG_SND_OMAP_SOC=m
CONFIG_SND_OMAP_SOC_OMAP3_PANDORA=m
CONFIG_USB=y
CONFIG_USB_DEBUG=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_DEVICEFS=y
CONFIG_USB_SUSPEND=y
# CONFIG_USB_OTG_WHITELIST is not set
CONFIG_USB_MON=y
# CONFIG_USB_MUSB_HDRC is not set
# CONFIG_USB_MUSB_OTG is not set
# CONFIG_USB_GADGET_MUSB_HDRC is not set
CONFIG_USB_MUSB_DEBUG=y
CONFIG_USB_WDM=y
CONFIG_USB_STORAGE=y
CONFIG_USB_LIBUSUAL=y
......@@ -250,18 +189,12 @@ CONFIG_MMC_UNSAFE_RESUME=y
CONFIG_SDIO_UART=y
CONFIG_MMC_OMAP=y
CONFIG_MMC_OMAP_HS=y
CONFIG_LEDS_CLASS=y
CONFIG_LEDS_GPIO=y
CONFIG_LEDS_TRIGGER_TIMER=y
CONFIG_LEDS_TRIGGER_HEARTBEAT=y
CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_TWL92330=y
CONFIG_RTC_DRV_TWL4030=y
CONFIG_EXT2_FS=y
CONFIG_EXT3_FS=y
# CONFIG_EXT3_FS_XATTR is not set
CONFIG_INOTIFY=y
CONFIG_QUOTA=y
CONFIG_QFMT_V2=y
CONFIG_MSDOS_FS=y
......@@ -285,12 +218,10 @@ CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_FS=y
CONFIG_DEBUG_KERNEL=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_PROVE_LOCKING=y
# CONFIG_LOCK_STAT is not set
CONFIG_DEBUG_SPINLOCK_SLEEP=y
# CONFIG_DEBUG_BUGVERBOSE is not set
CONFIG_DEBUG_INFO=y
......
......@@ -288,6 +288,7 @@ config MACH_IGEP0030
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
select MACH_IGEP0020
config MACH_SBC3530
bool "OMAP3 SBC STALKER board"
......
......@@ -229,8 +229,6 @@ obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o \
obj-$(CONFIG_MACH_CM_T3517) += board-cm-t3517.o
obj-$(CONFIG_MACH_IGEP0020) += board-igep0020.o \
hsmmc.o
obj-$(CONFIG_MACH_IGEP0030) += board-igep0030.o \
hsmmc.o
obj-$(CONFIG_MACH_OMAP3_TOUCHBOOK) += board-omap3touchbook.o \
hsmmc.o
obj-$(CONFIG_MACH_OMAP_4430SDP) += board-4430sdp.o \
......@@ -270,3 +268,5 @@ obj-$(CONFIG_ARCH_OMAP4) += hwspinlock.o
disp-$(CONFIG_OMAP2_DSS) := display.o
obj-y += $(disp-m) $(disp-y)
obj-y += common-board-devices.o
......@@ -41,6 +41,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define SDP2430_CS0_BASE 0x04000000
#define SECONDARY_LCD_GPIO 147
......@@ -180,15 +181,6 @@ static struct twl4030_platform_data sdp2430_twldata = {
.vmmc1 = &sdp2430_vmmc1,
};
static struct i2c_board_info __initdata sdp2430_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_24XX_SYS_NIRQ,
.platform_data = &sdp2430_twldata,
},
};
static struct i2c_board_info __initdata sdp2430_i2c1_boardinfo[] = {
{
I2C_BOARD_INFO("isp1301_omap", 0x2D),
......@@ -201,8 +193,7 @@ static int __init omap2430_i2c_init(void)
{
omap_register_i2c_bus(1, 100, sdp2430_i2c1_boardinfo,
ARRAY_SIZE(sdp2430_i2c1_boardinfo));
omap_register_i2c_bus(2, 2600, sdp2430_i2c_boardinfo,
ARRAY_SIZE(sdp2430_i2c_boardinfo));
omap2_pmic_init("twl4030", &sdp2430_twldata);
return 0;
}
......@@ -217,11 +208,6 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
{} /* Terminator */
};
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static struct omap_usb_config sdp2430_usb_config __initdata = {
.otg = 1,
#ifdef CONFIG_USB_GADGET_OMAP
......@@ -240,8 +226,6 @@ static struct omap_board_mux board_mux[] __initdata = {
static void __init omap_2430sdp_init(void)
{
int ret;
omap2430_mux_init(board_mux, OMAP_PACKAGE_ZAC);
omap_board_config = sdp2430_config;
......@@ -255,14 +239,13 @@ static void __init omap_2430sdp_init(void)
omap2_usbfs_init(&sdp2430_usb_config);
omap_mux_init_signal("usb0hs_stp", OMAP_PULL_ENA | OMAP_PULL_UP);
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
board_smc91x_init();
/* Turn off secondary LCD backlight */
ret = gpio_request(SECONDARY_LCD_GPIO, "Secondary LCD backlight");
if (ret == 0)
gpio_direction_output(SECONDARY_LCD_GPIO, 0);
gpio_request_one(SECONDARY_LCD_GPIO, GPIOF_OUT_INIT_LOW,
"Secondary LCD backlight");
}
static void __init omap_2430sdp_map_io(void)
......
......@@ -19,7 +19,6 @@
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/io.h>
......@@ -48,6 +47,7 @@
#include "hsmmc.h"
#include "pm.h"
#include "control.h"
#include "common-board-devices.h"
#define CONFIG_DISABLE_HFCLK 1
......@@ -59,24 +59,6 @@
#define TWL4030_MSECURE_GPIO 22
/* FIXME: These values need to be updated based on more profiling on 3430sdp*/
static struct cpuidle_params omap3_cpuidle_params_table[] = {
/* C1 */
{1, 2, 2, 5},
/* C2 */
{1, 10, 10, 30},
/* C3 */
{1, 50, 50, 300},
/* C4 */
{1, 1500, 1800, 4000},
/* C5 */
{1, 2500, 7500, 12000},
/* C6 */
{1, 3000, 8500, 15000},
/* C7 */
{1, 10000, 30000, 300000},
};
static uint32_t board_keymap[] = {
KEY(0, 0, KEY_LEFT),
KEY(0, 1, KEY_RIGHT),
......@@ -123,63 +105,14 @@ static struct twl4030_keypad_data sdp3430_kp_data = {
.rep = 1,
};
static int ts_gpio; /* Needed for ads7846_get_pendown_state */
/**
* @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
*
* @return - void. If request gpio fails then Flag KERN_ERR.
*/
static void ads7846_dev_init(void)
{
if (gpio_request(ts_gpio, "ADS7846 pendown") < 0) {
printk(KERN_ERR "can't get ads746 pen down GPIO\n");
return;
}
gpio_direction_input(ts_gpio);
gpio_set_debounce(ts_gpio, 310);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(ts_gpio);
}
static struct ads7846_platform_data tsc2046_config __initdata = {
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
.wakeup = true,
};
static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info sdp3430_spi_board_info[] __initdata = {
[0] = {
/*
* TSC2046 operates at a max freqency of 2MHz, so
* operate slightly below at 1.5MHz
*/
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &tsc2046_mcspi_config,
.irq = 0,
.platform_data = &tsc2046_config,
},
};
#define SDP3430_LCD_PANEL_BACKLIGHT_GPIO 8
#define SDP3430_LCD_PANEL_ENABLE_GPIO 5
static unsigned backlight_gpio;
static unsigned enable_gpio;
static struct gpio sdp3430_dss_gpios[] __initdata = {
{SDP3430_LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW, "LCD reset" },
{SDP3430_LCD_PANEL_BACKLIGHT_GPIO, GPIOF_OUT_INIT_LOW, "LCD Backlight"},
};
static int lcd_enabled;
static int dvi_enabled;
......@@ -187,29 +120,11 @@ static void __init sdp3430_display_init(void)
{
int r;
enable_gpio = SDP3430_LCD_PANEL_ENABLE_GPIO;
backlight_gpio = SDP3430_LCD_PANEL_BACKLIGHT_GPIO;
r = gpio_request_array(sdp3430_dss_gpios,
ARRAY_SIZE(sdp3430_dss_gpios));
if (r)
printk(KERN_ERR "failed to get LCD control GPIOs\n");
r = gpio_request(enable_gpio, "LCD reset");
if (r) {
printk(KERN_ERR "failed to get LCD reset GPIO\n");
goto err0;
}
r = gpio_request(backlight_gpio, "LCD Backlight");
if (r) {
printk(KERN_ERR "failed to get LCD backlight GPIO\n");
goto err1;
}
gpio_direction_output(enable_gpio, 0);
gpio_direction_output(backlight_gpio, 0);
return;
err1:
gpio_free(enable_gpio);
err0:
return;
}
static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev)
......@@ -219,8 +134,8 @@ static int sdp3430_panel_enable_lcd(struct omap_dss_device *dssdev)
return -EINVAL;
}
gpio_direction_output(enable_gpio, 1);
gpio_direction_output(backlight_gpio, 1);
gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 1);
gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 1);
lcd_enabled = 1;
......@@ -231,8 +146,8 @@ static void sdp3430_panel_disable_lcd(struct omap_dss_device *dssdev)
{
lcd_enabled = 0;
gpio_direction_output(enable_gpio, 0);
gpio_direction_output(backlight_gpio, 0);
gpio_direction_output(SDP3430_LCD_PANEL_ENABLE_GPIO, 0);
gpio_direction_output(SDP3430_LCD_PANEL_BACKLIGHT_GPIO, 0);
}
static int sdp3430_panel_enable_dvi(struct omap_dss_device *dssdev)
......@@ -360,12 +275,10 @@ static int sdp3430_twl_gpio_setup(struct device *dev,
omap2_hsmmc_init(mmc);
/* gpio + 7 is "sub_lcd_en_bkl" (output/PWM1) */
gpio_request(gpio + 7, "sub_lcd_en_bkl");
gpio_direction_output(gpio + 7, 0);
gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "sub_lcd_en_bkl");
/* gpio + 15 is "sub_lcd_nRST" (output) */
gpio_request(gpio + 15, "sub_lcd_nRST");
gpio_direction_output(gpio + 15, 0);
gpio_request_one(gpio + 15, GPIOF_OUT_INIT_LOW, "sub_lcd_nRST");
return 0;
}
......@@ -580,20 +493,10 @@ static struct twl4030_platform_data sdp3430_twldata = {
.vpll2 = &sdp3430_vpll2,
};
static struct i2c_board_info __initdata sdp3430_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &sdp3430_twldata,
},
};
static int __init omap3430_i2c_init(void)
{
/* i2c1 for PMIC only */
omap_register_i2c_bus(1, 2600, sdp3430_i2c_boardinfo,
ARRAY_SIZE(sdp3430_i2c_boardinfo));
omap3_pmic_init("twl4030", &sdp3430_twldata);
/* i2c2 on camera connector (for sensor control) and optional isp1301 */
omap_register_i2c_bus(2, 400, NULL, 0);
/* i2c3 on display connector (for DVI, tfp410) */
......@@ -872,30 +775,22 @@ static struct flash_partitions sdp_flash_partitions[] = {
},
};
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init omap_3430sdp_init(void)
{
int gpio_pendown;
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_board_config = sdp3430_config;
omap_board_config_size = ARRAY_SIZE(sdp3430_config);
omap3_pm_init_cpuidle(omap3_cpuidle_params_table);
omap3430_i2c_init();
omap_display_init(&sdp3430_dss_data);
if (omap_rev() > OMAP3430_REV_ES1_0)
ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV2;
gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV2;
else
ts_gpio = SDP3430_TS_GPIO_IRQ_SDPV1;
sdp3430_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
spi_register_board_info(sdp3430_spi_board_info,
ARRAY_SIZE(sdp3430_spi_board_info));
ads7846_dev_init();
gpio_pendown = SDP3430_TS_GPIO_IRQ_SDPV1;
omap_ads7846_init(1, gpio_pendown, 310, NULL);
board_serial_init();
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
board_smc91x_init();
board_flash_init(sdp_flash_partitions, chip_sel_3430, 0);
sdp3430_display_init();
......
......@@ -42,6 +42,7 @@
#include "hsmmc.h"
#include "timer-gp.h"
#include "control.h"
#include "common-board-devices.h"
#define ETH_KS8851_IRQ 34
#define ETH_KS8851_POWER_ON 48
......@@ -251,58 +252,22 @@ static struct spi_board_info sdp4430_spi_board_info[] __initdata = {
},
};
static struct gpio sdp4430_eth_gpios[] __initdata = {
{ ETH_KS8851_POWER_ON, GPIOF_OUT_INIT_HIGH, "eth_power" },
{ ETH_KS8851_QUART, GPIOF_OUT_INIT_HIGH, "quart" },
{ ETH_KS8851_IRQ, GPIOF_IN, "eth_irq" },
};
static int omap_ethernet_init(void)
{
int status;
/* Request of GPIO lines */
status = gpio_request_array(sdp4430_eth_gpios,
ARRAY_SIZE(sdp4430_eth_gpios));
if (status)
pr_err("Cannot request ETH GPIOs\n");
status = gpio_request(ETH_KS8851_POWER_ON, "eth_power");
if (status) {
pr_err("Cannot request GPIO %d\n", ETH_KS8851_POWER_ON);
return status;
}
status = gpio_request(ETH_KS8851_QUART, "quart");
if (status) {
pr_err("Cannot request GPIO %d\n", ETH_KS8851_QUART);
goto error1;
}
status = gpio_request(ETH_KS8851_IRQ, "eth_irq");
if (status) {
pr_err("Cannot request GPIO %d\n", ETH_KS8851_IRQ);
goto error2;
}
/* Configuration of requested GPIO lines */
status = gpio_direction_output(ETH_KS8851_POWER_ON, 1);
if (status) {
pr_err("Cannot set output GPIO %d\n", ETH_KS8851_IRQ);
goto error3;
}
status = gpio_direction_output(ETH_KS8851_QUART, 1);
if (status) {
pr_err("Cannot set output GPIO %d\n", ETH_KS8851_QUART);
goto error3;
}
status = gpio_direction_input(ETH_KS8851_IRQ);
if (status) {
pr_err("Cannot set input GPIO %d\n", ETH_KS8851_IRQ);
goto error3;
}
return 0;
error3:
gpio_free(ETH_KS8851_IRQ);
error2:
gpio_free(ETH_KS8851_QUART);
error1:
gpio_free(ETH_KS8851_POWER_ON);
return status;
}
......@@ -575,14 +540,6 @@ static struct twl4030_platform_data sdp4430_twldata = {
.usb = &omap4_usbphy_data
};
static struct i2c_board_info __initdata sdp4430_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl6030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = OMAP44XX_IRQ_SYS_1N,
.platform_data = &sdp4430_twldata,
},
};
static struct i2c_board_info __initdata sdp4430_i2c_3_boardinfo[] = {
{
I2C_BOARD_INFO("tmp105", 0x48),
......@@ -598,12 +555,7 @@ static struct i2c_board_info __initdata sdp4430_i2c_4_boardinfo[] = {
};
static int __init omap4_i2c_init(void)
{
/*
* Phoenix Audio IC needs I2C1 to
* start with 400 KHz or less
*/
omap_register_i2c_bus(1, 400, sdp4430_i2c_boardinfo,
ARRAY_SIZE(sdp4430_i2c_boardinfo));
omap4_pmic_init("twl6030", &sdp4430_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, sdp4430_i2c_3_boardinfo,
ARRAY_SIZE(sdp4430_i2c_3_boardinfo));
......@@ -616,19 +568,11 @@ static void __init omap_sfh7741prox_init(void)
{
int error;
error = gpio_request(OMAP4_SFH7741_ENABLE_GPIO, "sfh7741");
if (error < 0) {
error = gpio_request_one(OMAP4_SFH7741_ENABLE_GPIO,
GPIOF_OUT_INIT_LOW, "sfh7741");
if (error < 0)
pr_err("%s:failed to request GPIO %d, error %d\n",
__func__, OMAP4_SFH7741_ENABLE_GPIO, error);
return;
}
error = gpio_direction_output(OMAP4_SFH7741_ENABLE_GPIO , 0);
if (error < 0) {
pr_err("%s: GPIO configuration failed: GPIO %d,error %d\n",
__func__, OMAP4_SFH7741_ENABLE_GPIO, error);
gpio_free(OMAP4_SFH7741_ENABLE_GPIO);
}
}
static void sdp4430_hdmi_mux_init(void)
......@@ -645,27 +589,19 @@ static void sdp4430_hdmi_mux_init(void)
OMAP_PIN_INPUT_PULLUP);
}
static struct gpio sdp4430_hdmi_gpios[] = {
{ HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_hpd" },
{ HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_ls_oe" },
};
static int sdp4430_panel_enable_hdmi(struct omap_dss_device *dssdev)
{
int status;
status = gpio_request_one(HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH,
"hdmi_gpio_hpd");
if (status) {
pr_err("Cannot request GPIO %d\n", HDMI_GPIO_HPD);
return status;
}
status = gpio_request_one(HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH,
"hdmi_gpio_ls_oe");
if (status) {
pr_err("Cannot request GPIO %d\n", HDMI_GPIO_LS_OE);
goto error1;
}
return 0;
error1:
gpio_free(HDMI_GPIO_HPD);
status = gpio_request_array(sdp4430_hdmi_gpios,
ARRAY_SIZE(sdp4430_hdmi_gpios));
if (status)
pr_err("%s: Cannot request HDMI GPIOs\n", __func__);
return status;
}
......
......@@ -89,19 +89,13 @@ static void __init am3517_crane_init(void)
return;
}
ret = gpio_request(GPIO_USB_POWER, "usb_ehci_enable");
ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH,
"usb_ehci_enable");
if (ret < 0) {
pr_err("Can not request GPIO %d\n", GPIO_USB_POWER);
return;
}
ret = gpio_direction_output(GPIO_USB_POWER, 1);
if (ret < 0) {
gpio_free(GPIO_USB_POWER);
pr_err("Unable to initialize EHCI power\n");
return;
}
usbhs_init(&usbhs_bdata);
}
......
......@@ -174,19 +174,14 @@ static void __init am3517_evm_rtc_init(void)
int r;
omap_mux_init_gpio(GPIO_RTCS35390A_IRQ, OMAP_PIN_INPUT_PULLUP);
r = gpio_request(GPIO_RTCS35390A_IRQ, "rtcs35390a-irq");
r = gpio_request_one(GPIO_RTCS35390A_IRQ, GPIOF_IN, "rtcs35390a-irq");
if (r < 0) {
printk(KERN_WARNING "failed to request GPIO#%d\n",
GPIO_RTCS35390A_IRQ);
return;
}
r = gpio_direction_input(GPIO_RTCS35390A_IRQ);
if (r < 0) {
printk(KERN_WARNING "GPIO#%d cannot be configured as input\n",
GPIO_RTCS35390A_IRQ);
gpio_free(GPIO_RTCS35390A_IRQ);
return;
}
am3517evm_i2c1_boardinfo[0].irq = gpio_to_irq(GPIO_RTCS35390A_IRQ);
}
......@@ -242,6 +237,15 @@ static int dvi_enabled;
#if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \
defined(CONFIG_PANEL_SHARP_LQ043T1DG01_MODULE)
static struct gpio am3517_evm_dss_gpios[] __initdata = {
/* GPIO 182 = LCD Backlight Power */
{ LCD_PANEL_BKLIGHT_PWR, GPIOF_OUT_INIT_HIGH, "lcd_backlight_pwr" },
/* GPIO 181 = LCD Panel PWM */
{ LCD_PANEL_PWM, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
/* GPIO 176 = LCD Panel Power enable pin */
{ LCD_PANEL_PWR, GPIOF_OUT_INIT_HIGH, "dvi enable" },
};
static void __init am3517_evm_display_init(void)
{
int r;
......@@ -249,41 +253,15 @@ static void __init am3517_evm_display_init(void)
omap_mux_init_gpio(LCD_PANEL_PWR, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(LCD_PANEL_BKLIGHT_PWR, OMAP_PIN_INPUT_PULLDOWN);
omap_mux_init_gpio(LCD_PANEL_PWM, OMAP_PIN_INPUT_PULLDOWN);
/*
* Enable GPIO 182 = LCD Backlight Power
*/
r = gpio_request(LCD_PANEL_BKLIGHT_PWR, "lcd_backlight_pwr");
r = gpio_request_array(am3517_evm_dss_gpios,
ARRAY_SIZE(am3517_evm_dss_gpios));
if (r) {
printk(KERN_ERR "failed to get lcd_backlight_pwr\n");
printk(KERN_ERR "failed to get DSS panel control GPIOs\n");
return;
}
gpio_direction_output(LCD_PANEL_BKLIGHT_PWR, 1);
/*
* Enable GPIO 181 = LCD Panel PWM
*/
r = gpio_request(LCD_PANEL_PWM, "lcd_pwm");
if (r) {
printk(KERN_ERR "failed to get lcd_pwm\n");
goto err_1;
}
gpio_direction_output(LCD_PANEL_PWM, 1);
/*
* Enable GPIO 176 = LCD Panel Power enable pin
*/
r = gpio_request(LCD_PANEL_PWR, "lcd_panel_pwr");
if (r) {
printk(KERN_ERR "failed to get lcd_panel_pwr\n");
goto err_2;
}
gpio_direction_output(LCD_PANEL_PWR, 1);
printk(KERN_INFO "Display initialized successfully\n");
return;
err_2:
gpio_free(LCD_PANEL_PWM);
err_1:
gpio_free(LCD_PANEL_BKLIGHT_PWR);
}
#else
static void __init am3517_evm_display_init(void) {}
......@@ -396,7 +374,7 @@ static struct omap_musb_board_data musb_board_data = {
.power = 500,
.set_phy_power = am35x_musb_phy_power,
.clear_irq = am35x_musb_clear_irq,
.set_mode = am35x_musb_set_mode,
.set_mode = am35x_set_mode,
.reset = am35x_musb_reset,
};
......
......@@ -202,6 +202,7 @@ static inline void __init apollon_init_smc91x(void)
unsigned int rate;
struct clk *gpmc_fck;
int eth_cs;
int err;
gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
if (IS_ERR(gpmc_fck)) {
......@@ -245,15 +246,13 @@ static inline void __init apollon_init_smc91x(void)
apollon_smc91x_resources[0].end = base + 0x30f;
udelay(100);
omap_mux_init_gpio(74, 0);
if (gpio_request(APOLLON_ETHR_GPIO_IRQ, "SMC91x irq") < 0) {
omap_mux_init_gpio(APOLLON_ETHR_GPIO_IRQ, 0);
err = gpio_request_one(APOLLON_ETHR_GPIO_IRQ, GPIOF_IN, "SMC91x irq");
if (err) {
printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
APOLLON_ETHR_GPIO_IRQ);
gpmc_cs_free(APOLLON_ETH_CS);
goto out;
}
gpio_direction_input(APOLLON_ETHR_GPIO_IRQ);
out:
clk_disable(gpmc_fck);
clk_put(gpmc_fck);
......@@ -280,20 +279,19 @@ static void __init omap_apollon_init_early(void)
omap2_init_common_devices(NULL, NULL);
}
static struct gpio apollon_gpio_leds[] __initdata = {
{ LED0_GPIO13, GPIOF_OUT_INIT_LOW, "LED0" }, /* LED0 - AA10 */
{ LED1_GPIO14, GPIOF_OUT_INIT_LOW, "LED1" }, /* LED1 - AA6 */
{ LED2_GPIO15, GPIOF_OUT_INIT_LOW, "LED2" }, /* LED2 - AA4 */
};
static void __init apollon_led_init(void)
{
/* LED0 - AA10 */
omap_mux_init_signal("vlynq_clk.gpio_13", 0);
gpio_request(LED0_GPIO13, "LED0");
gpio_direction_output(LED0_GPIO13, 0);
/* LED1 - AA6 */
omap_mux_init_signal("vlynq_rx1.gpio_14", 0);
gpio_request(LED1_GPIO14, "LED1");
gpio_direction_output(LED1_GPIO14, 0);
/* LED2 - AA4 */
omap_mux_init_signal("vlynq_rx0.gpio_15", 0);
gpio_request(LED2_GPIO15, "LED2");
gpio_direction_output(LED2_GPIO15, 0);
gpio_request_array(apollon_gpio_leds, ARRAY_SIZE(apollon_gpio_leds));
}
static void __init apollon_usb_init(void)
......@@ -301,8 +299,7 @@ static void __init apollon_usb_init(void)
/* USB device */
/* DEVICE_SUSPEND */
omap_mux_init_signal("mcbsp2_clkx.gpio_12", 0);
gpio_request(12, "USB suspend");
gpio_direction_output(12, 0);
gpio_request_one(12, GPIOF_OUT_INIT_LOW, "USB suspend");
omap2_usbfs_init(&apollon_usb_config);
}
......
......@@ -54,6 +54,7 @@
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define CM_T35_GPIO_PENDOWN 57
......@@ -66,86 +67,28 @@
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
#include <plat/gpmc-smsc911x.h>
static struct smsc911x_platform_config cm_t35_smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct resource cm_t35_smsc911x_resources[] = {
{
.flags = IORESOURCE_MEM,
},
{
.start = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
.end = OMAP_GPIO_IRQ(CM_T35_SMSC911X_GPIO),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
static struct platform_device cm_t35_smsc911x_device = {
.name = "smsc911x",
static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
.id = 0,
.num_resources = ARRAY_SIZE(cm_t35_smsc911x_resources),
.resource = cm_t35_smsc911x_resources,
.dev = {
.platform_data = &cm_t35_smsc911x_config,
},
};
static struct resource sb_t35_smsc911x_resources[] = {
{
.flags = IORESOURCE_MEM,
},
{
.start = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
.end = OMAP_GPIO_IRQ(SB_T35_SMSC911X_GPIO),
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
.cs = CM_T35_SMSC911X_CS,
.gpio_irq = CM_T35_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static struct platform_device sb_t35_smsc911x_device = {
.name = "smsc911x",
static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
.id = 1,
.num_resources = ARRAY_SIZE(sb_t35_smsc911x_resources),
.resource = sb_t35_smsc911x_resources,
.dev = {
.platform_data = &cm_t35_smsc911x_config,
},
.cs = SB_T35_SMSC911X_CS,
.gpio_irq = SB_T35_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static void __init cm_t35_init_smsc911x(struct platform_device *dev,
int cs, int irq_gpio)
{
unsigned long cs_mem_base;
if (gpmc_cs_request(cs, SZ_16M, &cs_mem_base) < 0) {
pr_err("CM-T35: Failed request for GPMC mem for smsc911x\n");
return;
}
dev->resource[0].start = cs_mem_base + 0x0;
dev->resource[0].end = cs_mem_base + 0xff;
if ((gpio_request(irq_gpio, "ETH IRQ") == 0) &&
(gpio_direction_input(irq_gpio) == 0)) {
gpio_export(irq_gpio, 0);
} else {
pr_err("CM-T35: could not obtain gpio for SMSC911X IRQ\n");
return;
}
platform_device_register(dev);
}
static void __init cm_t35_init_ethernet(void)
{
cm_t35_init_smsc911x(&cm_t35_smsc911x_device,
CM_T35_SMSC911X_CS, CM_T35_SMSC911X_GPIO);
cm_t35_init_smsc911x(&sb_t35_smsc911x_device,
SB_T35_SMSC911X_CS, SB_T35_SMSC911X_GPIO);
gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
}
#else
static inline void __init cm_t35_init_ethernet(void) { return; }
......@@ -235,69 +178,10 @@ static void __init cm_t35_init_nand(void)
static inline void cm_t35_init_nand(void) {}
#endif
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
#include <linux/spi/ads7846.h>
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(CM_T35_GPIO_PENDOWN);
}
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
};
static struct spi_board_info cm_t35_spi_board_info[] __initdata = {
{
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(CM_T35_GPIO_PENDOWN),
.platform_data = &ads7846_config,
},
};
static void __init cm_t35_init_ads7846(void)
{
if ((gpio_request(CM_T35_GPIO_PENDOWN, "ADS7846_PENDOWN") == 0) &&
(gpio_direction_input(CM_T35_GPIO_PENDOWN) == 0)) {
gpio_export(CM_T35_GPIO_PENDOWN, 0);
} else {
pr_err("CM-T35: could not obtain gpio for ADS7846_PENDOWN\n");
return;
}
spi_register_board_info(cm_t35_spi_board_info,
ARRAY_SIZE(cm_t35_spi_board_info));
}
#else
static inline void cm_t35_init_ads7846(void) {}
#endif
#define CM_T35_LCD_EN_GPIO 157
#define CM_T35_LCD_BL_GPIO 58
#define CM_T35_DVI_EN_GPIO 54
static int lcd_bl_gpio;
static int lcd_en_gpio;
static int dvi_en_gpio;
static int lcd_enabled;
static int dvi_enabled;
......@@ -308,8 +192,8 @@ static int cm_t35_panel_enable_lcd(struct omap_dss_device *dssdev)
return -EINVAL;
}
gpio_set_value(lcd_en_gpio, 1);
gpio_set_value(lcd_bl_gpio, 1);
gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
gpio_set_value(CM_T35_LCD_BL_GPIO, 1);
lcd_enabled = 1;
......@@ -320,8 +204,8 @@ static void cm_t35_panel_disable_lcd(struct omap_dss_device *dssdev)
{
lcd_enabled = 0;
gpio_set_value(lcd_bl_gpio, 0);
gpio_set_value(lcd_en_gpio, 0);
gpio_set_value(CM_T35_LCD_BL_GPIO, 0);
gpio_set_value(CM_T35_LCD_EN_GPIO, 0);
}
static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
......@@ -331,7 +215,7 @@ static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
return -EINVAL;
}
gpio_set_value(dvi_en_gpio, 0);
gpio_set_value(CM_T35_DVI_EN_GPIO, 0);
dvi_enabled = 1;
return 0;
......@@ -339,7 +223,7 @@ static int cm_t35_panel_enable_dvi(struct omap_dss_device *dssdev)
static void cm_t35_panel_disable_dvi(struct omap_dss_device *dssdev)
{
gpio_set_value(dvi_en_gpio, 1);
gpio_set_value(CM_T35_DVI_EN_GPIO, 1);
dvi_enabled = 0;
}
......@@ -421,62 +305,38 @@ static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = {
},
};
static struct gpio cm_t35_dss_gpios[] __initdata = {
{ CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW, "lcd enable" },
{ CM_T35_LCD_BL_GPIO, GPIOF_OUT_INIT_LOW, "lcd bl enable" },
{ CM_T35_DVI_EN_GPIO, GPIOF_OUT_INIT_HIGH, "dvi enable" },
};
static void __init cm_t35_init_display(void)
{
int err;
lcd_en_gpio = CM_T35_LCD_EN_GPIO;
lcd_bl_gpio = CM_T35_LCD_BL_GPIO;
dvi_en_gpio = CM_T35_DVI_EN_GPIO;
spi_register_board_info(cm_t35_lcd_spi_board_info,
ARRAY_SIZE(cm_t35_lcd_spi_board_info));
err = gpio_request(lcd_en_gpio, "LCD RST");
if (err) {
pr_err("CM-T35: failed to get LCD reset GPIO\n");
goto out;
}
err = gpio_request(lcd_bl_gpio, "LCD BL");
if (err) {
pr_err("CM-T35: failed to get LCD backlight control GPIO\n");
goto err_lcd_bl;
}
err = gpio_request(dvi_en_gpio, "DVI EN");
err = gpio_request_array(cm_t35_dss_gpios,
ARRAY_SIZE(cm_t35_dss_gpios));
if (err) {
pr_err("CM-T35: failed to get DVI reset GPIO\n");
goto err_dvi_en;
pr_err("CM-T35: failed to request DSS control GPIOs\n");
return;
}
gpio_export(lcd_en_gpio, 0);
gpio_export(lcd_bl_gpio, 0);
gpio_export(dvi_en_gpio, 0);
gpio_direction_output(lcd_en_gpio, 0);
gpio_direction_output(lcd_bl_gpio, 0);
gpio_direction_output(dvi_en_gpio, 1);
gpio_export(CM_T35_LCD_EN_GPIO, 0);
gpio_export(CM_T35_LCD_BL_GPIO, 0);
gpio_export(CM_T35_DVI_EN_GPIO, 0);
msleep(50);
gpio_set_value(lcd_en_gpio, 1);
gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
err = omap_display_init(&cm_t35_dss_data);
if (err) {
pr_err("CM-T35: failed to register DSS device\n");
goto err_dev_reg;
gpio_free_array(cm_t35_dss_gpios, ARRAY_SIZE(cm_t35_dss_gpios));
}
return;
err_dev_reg:
gpio_free(dvi_en_gpio);
err_dvi_en:
gpio_free(lcd_bl_gpio);
err_lcd_bl:
gpio_free(lcd_en_gpio);
out:
return;
}
static struct regulator_consumer_supply cm_t35_vmmc1_supply = {
......@@ -609,10 +469,8 @@ static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
{
int wlan_rst = gpio + 2;
if ((gpio_request(wlan_rst, "WLAN RST") == 0) &&
(gpio_direction_output(wlan_rst, 1) == 0)) {
if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
gpio_export(wlan_rst, 0);
udelay(10);
gpio_set_value(wlan_rst, 0);
udelay(10);
......@@ -653,19 +511,9 @@ static struct twl4030_platform_data cm_t35_twldata = {
.vpll2 = &cm_t35_vpll2,
};
static struct i2c_board_info __initdata cm_t35_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("tps65930", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &cm_t35_twldata,
},
};
static void __init cm_t35_init_i2c(void)
{
omap_register_i2c_bus(1, 2600, cm_t35_i2c_boardinfo,
ARRAY_SIZE(cm_t35_i2c_boardinfo));
omap3_pmic_init("tps65930", &cm_t35_twldata);
}
static void __init cm_t35_init_early(void)
......@@ -775,12 +623,6 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static struct omap_board_config_kernel cm_t35_config[] __initdata = {
};
......@@ -792,12 +634,12 @@ static void __init cm_t35_init(void)
omap_serial_init();
cm_t35_init_i2c();
cm_t35_init_nand();
cm_t35_init_ads7846();
omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
cm_t35_init_ethernet();
cm_t35_init_led();
cm_t35_init_display();
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
}
......
......@@ -148,14 +148,13 @@ static void __init cm_t3517_init_rtc(void)
{
int err;
err = gpio_request(RTC_CS_EN_GPIO, "rtc cs en");
err = gpio_request_one(RTC_CS_EN_GPIO, GPIOF_OUT_INIT_HIGH,
"rtc cs en");
if (err) {
pr_err("CM-T3517: rtc cs en gpio request failed: %d\n", err);
return;
}
gpio_direction_output(RTC_CS_EN_GPIO, 1);
platform_device_register(&cm_t3517_rtc_device);
}
#else
......@@ -182,11 +181,11 @@ static int cm_t3517_init_usbh(void)
{
int err;
err = gpio_request(USB_HUB_RESET_GPIO, "usb hub rst");
err = gpio_request_one(USB_HUB_RESET_GPIO, GPIOF_OUT_INIT_LOW,
"usb hub rst");
if (err) {
pr_err("CM-T3517: usb hub rst gpio request failed: %d\n", err);
} else {
gpio_direction_output(USB_HUB_RESET_GPIO, 0);
udelay(10);
gpio_set_value(USB_HUB_RESET_GPIO, 1);
msleep(1);
......
......@@ -51,7 +51,6 @@
#include <plat/mcspi.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/dm9000.h>
#include <linux/interrupt.h>
......@@ -60,6 +59,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
#include "common-board-devices.h"
#define NAND_BLOCK_SIZE SZ_128K
......@@ -97,13 +97,6 @@ static struct mtd_partition devkit8000_nand_partitions[] = {
},
};
static struct omap_nand_platform_data devkit8000_nand_data = {
.options = NAND_BUSWIDTH_16,
.parts = devkit8000_nand_partitions,
.nr_parts = ARRAY_SIZE(devkit8000_nand_partitions),
.dma_channel = -1, /* disable DMA in OMAP NAND driver */
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
......@@ -249,7 +242,7 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
/* TWL4030_GPIO_MAX + 0 is "LCD_PWREN" (out, active high) */
devkit8000_lcd_device.reset_gpio = gpio + TWL4030_GPIO_MAX + 0;
ret = gpio_request_one(devkit8000_lcd_device.reset_gpio,
GPIOF_DIR_OUT | GPIOF_INIT_LOW, "LCD_PWREN");
GPIOF_OUT_INIT_LOW, "LCD_PWREN");
if (ret < 0) {
devkit8000_lcd_device.reset_gpio = -EINVAL;
printk(KERN_ERR "Failed to request GPIO for LCD_PWRN\n");
......@@ -258,7 +251,7 @@ static int devkit8000_twl_gpio_setup(struct device *dev,
/* gpio + 7 is "DVI_PD" (out, active low) */
devkit8000_dvi_device.reset_gpio = gpio + 7;
ret = gpio_request_one(devkit8000_dvi_device.reset_gpio,
GPIOF_DIR_OUT | GPIOF_INIT_LOW, "DVI PowerDown");
GPIOF_OUT_INIT_LOW, "DVI PowerDown");
if (ret < 0) {
devkit8000_dvi_device.reset_gpio = -EINVAL;
printk(KERN_ERR "Failed to request GPIO for DVI PowerDown\n");
......@@ -366,19 +359,9 @@ static struct twl4030_platform_data devkit8000_twldata = {
.keypad = &devkit8000_kp_data,
};
static struct i2c_board_info __initdata devkit8000_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("tps65930", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &devkit8000_twldata,
},
};
static int __init devkit8000_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, devkit8000_i2c_boardinfo,
ARRAY_SIZE(devkit8000_i2c_boardinfo));
omap3_pmic_init("tps65930", &devkit8000_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 400, NULL, 0);
......@@ -463,56 +446,6 @@ static void __init devkit8000_init_irq(void)
#endif
}
static void __init devkit8000_ads7846_init(void)
{
int gpio = OMAP3_DEVKIT_TS_GPIO;
int ret;
ret = gpio_request(gpio, "ads7846_pen_down");
if (ret < 0) {
printk(KERN_ERR "Failed to request GPIO %d for "
"ads7846 pen down IRQ\n", gpio);
return;
}
gpio_direction_input(gpio);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(OMAP3_DEVKIT_TS_GPIO);
}
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 5,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
.settle_delay_usecs = 150,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info devkit8000_spi_board_info[] __initdata = {
{
.modalias = "ads7846",
.bus_num = 2,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_DEVKIT_TS_GPIO),
.platform_data = &ads7846_config,
}
};
#define OMAP_DM9000_BASE 0x2c000000
static struct resource omap_dm9000_resources[] = {
......@@ -550,15 +483,15 @@ static void __init omap_dm9000_init(void)
{
unsigned char *eth_addr = omap_dm9000_platdata.dev_addr;
struct omap_die_id odi;
int ret;
if (gpio_request(OMAP_DM9000_GPIO_IRQ, "dm9000 irq") < 0) {
ret = gpio_request_one(OMAP_DM9000_GPIO_IRQ, GPIOF_IN, "dm9000 irq");
if (ret < 0) {
printk(KERN_ERR "Failed to request GPIO%d for dm9000 IRQ\n",
OMAP_DM9000_GPIO_IRQ);
return;
}
gpio_direction_input(OMAP_DM9000_GPIO_IRQ);
/* init the mac address using DIE id */
omap_get_die_id(&odi);
......@@ -576,45 +509,6 @@ static struct platform_device *devkit8000_devices[] __initdata = {
&omap_dm9000_dev,
};
static void __init devkit8000_flash_init(void)
{
u8 cs = 0;
u8 nandcs = GPMC_CS_NUM + 1;
/* find out the chip-select on which NAND exists */
while (cs < GPMC_CS_NUM) {
u32 ret = 0;
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
if ((ret & 0xC00) == 0x800) {
printk(KERN_INFO "Found NAND on CS%d\n", cs);
if (nandcs > GPMC_CS_NUM)
nandcs = cs;
}
cs++;
}
if (nandcs > GPMC_CS_NUM) {
printk(KERN_INFO "NAND: Unable to find configuration "
"in GPMC\n ");
return;
}
if (nandcs < GPMC_CS_NUM) {
devkit8000_nand_data.cs = nandcs;
printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
if (gpmc_nand_init(&devkit8000_nand_data) < 0)
printk(KERN_ERR "Unable to register NAND device\n");
}
}
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
......@@ -795,14 +689,13 @@ static void __init devkit8000_init(void)
ARRAY_SIZE(devkit8000_devices));
omap_display_init(&devkit8000_dss_data);
spi_register_board_info(devkit8000_spi_board_info,
ARRAY_SIZE(devkit8000_spi_board_info));
devkit8000_ads7846_init();
omap_ads7846_init(2, OMAP3_DEVKIT_TS_GPIO, 0, NULL);
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
devkit8000_flash_init();
omap_nand_flash_init(NAND_BUSWIDTH_16, devkit8000_nand_partitions,
ARRAY_SIZE(devkit8000_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
......
This diff is collapsed.
This diff is collapsed.
......@@ -22,7 +22,6 @@
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <linux/io.h>
......@@ -43,47 +42,19 @@
#include <asm/delay.h>
#include <plat/usb.h>
#include <plat/gpmc-smsc911x.h>
#include "board-flash.h"
#include "mux.h"
#include "hsmmc.h"
#include "control.h"
#include "common-board-devices.h"
#define LDP_SMSC911X_CS 1
#define LDP_SMSC911X_GPIO 152
#define DEBUG_BASE 0x08000000
#define LDP_ETHR_START DEBUG_BASE
static struct resource ldp_smsc911x_resources[] = {
[0] = {
.start = LDP_ETHR_START,
.end = LDP_ETHR_START + SZ_4K,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = 0,
.end = 0,
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
static struct smsc911x_platform_config ldp_smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
.flags = SMSC911X_USE_32BIT,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct platform_device ldp_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(ldp_smsc911x_resources),
.resource = ldp_smsc911x_resources,
.dev = {
.platform_data = &ldp_smsc911x_config,
},
};
static uint32_t board_keymap[] = {
KEY(0, 0, KEY_1),
KEY(1, 0, KEY_2),
......@@ -197,82 +168,16 @@ static struct platform_device ldp_gpio_keys_device = {
},
};
static int ts_gpio;
/**
* @brief ads7846_dev_init : Requests & sets GPIO line for pen-irq
*
* @return - void. If request gpio fails then Flag KERN_ERR.
*/
static void ads7846_dev_init(void)
{
if (gpio_request(ts_gpio, "ads7846 irq") < 0) {
printk(KERN_ERR "can't get ads746 pen down GPIO\n");
return;
}
gpio_direction_input(ts_gpio);
gpio_set_debounce(ts_gpio, 310);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(ts_gpio);
}
static struct ads7846_platform_data tsc2046_config __initdata = {
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
};
static struct omap2_mcspi_device_config tsc2046_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info ldp_spi_board_info[] __initdata = {
[0] = {
/*
* TSC2046 operates at a max freqency of 2MHz, so
* operate slightly below at 1.5MHz
*/
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &tsc2046_mcspi_config,
.irq = 0,
.platform_data = &tsc2046_config,
},
static struct omap_smsc911x_platform_data smsc911x_cfg = {
.cs = LDP_SMSC911X_CS,
.gpio_irq = LDP_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
};
static inline void __init ldp_init_smsc911x(void)
{
int eth_cs;
unsigned long cs_mem_base;
int eth_gpio = 0;
eth_cs = LDP_SMSC911X_CS;
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
return;
}
ldp_smsc911x_resources[0].start = cs_mem_base + 0x0;
ldp_smsc911x_resources[0].end = cs_mem_base + 0xff;
udelay(100);
eth_gpio = LDP_SMSC911X_GPIO;
ldp_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
eth_gpio);
return;
}
gpio_direction_input(eth_gpio);
gpmc_smsc911x_init(&smsc911x_cfg);
}
static struct platform_device ldp_lcd_device = {
......@@ -360,19 +265,9 @@ static struct twl4030_platform_data ldp_twldata = {
.keypad = &ldp_kp_twl4030_data,
};
static struct i2c_board_info __initdata ldp_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &ldp_twldata,
},
};
static int __init omap_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, ldp_i2c_boardinfo,
ARRAY_SIZE(ldp_i2c_boardinfo));
omap3_pmic_init("twl4030", &ldp_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
......@@ -389,7 +284,6 @@ static struct omap2_hsmmc_info mmc[] __initdata = {
};
static struct platform_device *ldp_devices[] __initdata = {
&ldp_smsc911x_device,
&ldp_lcd_device,
&ldp_gpio_keys_device,
};
......@@ -400,12 +294,6 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static struct mtd_partition ldp_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
{
......@@ -446,13 +334,9 @@ static void __init omap_ldp_init(void)
ldp_init_smsc911x();
omap_i2c_init();
platform_add_devices(ldp_devices, ARRAY_SIZE(ldp_devices));
ts_gpio = 54;
ldp_spi_board_info[0].irq = gpio_to_irq(ts_gpio);
spi_register_board_info(ldp_spi_board_info,
ARRAY_SIZE(ldp_spi_board_info));
ads7846_dev_init();
omap_ads7846_init(1, 54, 310, NULL);
omap_serial_init();
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
board_nand_init(ldp_nand_partitions,
ARRAY_SIZE(ldp_nand_partitions), ZOOM_NAND_CS, 0);
......
......@@ -106,14 +106,13 @@ static void __init n8x0_usb_init(void)
static char announce[] __initdata = KERN_INFO "TUSB 6010\n";
/* PM companion chip power control pin */
ret = gpio_request(TUSB6010_GPIO_ENABLE, "TUSB6010 enable");
ret = gpio_request_one(TUSB6010_GPIO_ENABLE, GPIOF_OUT_INIT_LOW,
"TUSB6010 enable");
if (ret != 0) {
printk(KERN_ERR "Could not get TUSB power GPIO%i\n",
TUSB6010_GPIO_ENABLE);
return;
}
gpio_direction_output(TUSB6010_GPIO_ENABLE, 0);
tusb_set_power(0);
ret = tusb6010_setup_interface(&tusb_data, TUSB6010_REFCLK_19, 2,
......@@ -494,8 +493,12 @@ static struct omap_mmc_platform_data mmc1_data = {
static struct omap_mmc_platform_data *mmc_data[OMAP24XX_NR_MMC];
static void __init n8x0_mmc_init(void)
static struct gpio n810_emmc_gpios[] __initdata = {
{ N810_EMMC_VSD_GPIO, GPIOF_OUT_INIT_LOW, "MMC slot 2 Vddf" },
{ N810_EMMC_VIO_GPIO, GPIOF_OUT_INIT_LOW, "MMC slot 2 Vdd" },
};
static void __init n8x0_mmc_init(void)
{
int err;
......@@ -512,27 +515,18 @@ static void __init n8x0_mmc_init(void)
mmc1_data.slots[1].ban_openended = 1;
}
err = gpio_request(N8X0_SLOT_SWITCH_GPIO, "MMC slot switch");
err = gpio_request_one(N8X0_SLOT_SWITCH_GPIO, GPIOF_OUT_INIT_LOW,
"MMC slot switch");
if (err)
return;
gpio_direction_output(N8X0_SLOT_SWITCH_GPIO, 0);
if (machine_is_nokia_n810()) {
err = gpio_request(N810_EMMC_VSD_GPIO, "MMC slot 2 Vddf");
err = gpio_request_array(n810_emmc_gpios,
ARRAY_SIZE(n810_emmc_gpios));
if (err) {
gpio_free(N8X0_SLOT_SWITCH_GPIO);
return;
}
gpio_direction_output(N810_EMMC_VSD_GPIO, 0);
err = gpio_request(N810_EMMC_VIO_GPIO, "MMC slot 2 Vdd");
if (err) {
gpio_free(N8X0_SLOT_SWITCH_GPIO);
gpio_free(N810_EMMC_VSD_GPIO);
return;
}
gpio_direction_output(N810_EMMC_VIO_GPIO, 0);
}
mmc_data[0] = &mmc1_data;
......
......@@ -52,6 +52,7 @@
#include "hsmmc.h"
#include "timer-gp.h"
#include "pm.h"
#include "common-board-devices.h"
#define NAND_BLOCK_SIZE SZ_128K
......@@ -79,6 +80,12 @@ static u8 omap3_beagle_get_rev(void)
return omap3_beagle_version;
}
static struct gpio omap3_beagle_rev_gpios[] __initdata = {
{ 171, GPIOF_IN, "rev_id_0" },
{ 172, GPIOF_IN, "rev_id_1" },
{ 173, GPIOF_IN, "rev_id_2" },
};
static void __init omap3_beagle_init_rev(void)
{
int ret;
......@@ -88,21 +95,13 @@ static void __init omap3_beagle_init_rev(void)
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
ret = gpio_request(171, "rev_id_0");
if (ret < 0)
goto fail0;
ret = gpio_request(172, "rev_id_1");
if (ret < 0)
goto fail1;
ret = gpio_request(173, "rev_id_2");
if (ret < 0)
goto fail2;
gpio_direction_input(171);
gpio_direction_input(172);
gpio_direction_input(173);
ret = gpio_request_array(omap3_beagle_rev_gpios,
ARRAY_SIZE(omap3_beagle_rev_gpios));
if (ret < 0) {
printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
return;
}
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
| (gpio_get_value(173) << 2);
......@@ -128,18 +127,6 @@ static void __init omap3_beagle_init_rev(void)
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
}
return;
fail2:
gpio_free(172);
fail1:
gpio_free(171);
fail0:
printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
return;
}
static struct mtd_partition omap3beagle_nand_partitions[] = {
......@@ -173,15 +160,6 @@ static struct mtd_partition omap3beagle_nand_partitions[] = {
},
};
static struct omap_nand_platform_data omap3beagle_nand_data = {
.options = NAND_BUSWIDTH_16,
.parts = omap3beagle_nand_partitions,
.nr_parts = ARRAY_SIZE(omap3beagle_nand_partitions),
.dma_channel = -1, /* disable DMA in OMAP NAND driver */
.nand_setup = NULL,
.dev_ready = NULL,
};
/* DSS */
static int beagle_enable_dvi(struct omap_dss_device *dssdev)
......@@ -243,13 +221,10 @@ static void __init beagle_display_init(void)
{
int r;
r = gpio_request(beagle_dvi_device.reset_gpio, "DVI reset");
if (r < 0) {
r = gpio_request_one(beagle_dvi_device.reset_gpio, GPIOF_OUT_INIT_LOW,
"DVI reset");
if (r < 0)
printk(KERN_ERR "Unable to get DVI reset GPIO\n");
return;
}
gpio_direction_output(beagle_dvi_device.reset_gpio, 0);
}
#include "sdram-micron-mt46h32m32lf-6.h"
......@@ -276,7 +251,7 @@ static struct gpio_led gpio_leds[];
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int r;
int r, usb_pwr_level;
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
mmc[0].gpio_wp = -EINVAL;
......@@ -295,66 +270,46 @@ static int beagle_twl_gpio_setup(struct device *dev,
beagle_vmmc1_supply.dev = mmc[0].dev;
beagle_vsim_supply.dev = mmc[0].dev;
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if (omap3_beagle_get_rev() != OMAP3BEAGLE_BOARD_XM) {
r = gpio_request(gpio + 1, "EHCI_nOC");
if (!r) {
r = gpio_direction_input(gpio + 1);
if (r)
gpio_free(gpio + 1);
}
if (r)
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
* DVI reset GPIO is different between beagle revisions
*/
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 1);
else
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
/* DVI reset GPIO is different between beagle revisions */
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM)
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
usb_pwr_level = GPIOF_OUT_INIT_HIGH;
beagle_dvi_device.reset_gpio = 129;
else
beagle_dvi_device.reset_gpio = 170;
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as follows:
* gpio + 2 control varies depending on the board rev as below:
* P7/P8 revisions(prototype): Camera EN
* A2+ revisions (production): LDO (supplies DVI, serial, led blocks)
* A2+ revisions (production): LDO (DVI, serial, led blocks)
*/
if (omap3_beagle_get_rev() == OMAP3BEAGLE_BOARD_XM) {
r = gpio_request(gpio + 1, "nDVI_PWR_EN");
if (!r) {
r = gpio_direction_output(gpio + 1, 0);
if (r)
gpio_free(gpio + 1);
}
r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
"nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
r = gpio_request(gpio + 2, "DVI_LDO_EN");
if (!r) {
r = gpio_direction_output(gpio + 2, 1);
if (r)
gpio_free(gpio + 2);
}
r = gpio_request_one(gpio + 2, GPIOF_OUT_INIT_HIGH,
"DVI_LDO_EN");
if (r)
pr_err("%s: unable to configure DVI_LDO_EN\n",
__func__);
} else {
usb_pwr_level = GPIOF_OUT_INIT_LOW;
beagle_dvi_device.reset_gpio = 170;
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
gpio_request_one(gpio + TWL4030_GPIO_MAX, usb_pwr_level, "nEN_USB_PWR");
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
return 0;
}
......@@ -453,15 +408,6 @@ static struct twl4030_platform_data beagle_twldata = {
.vpll2 = &beagle_vpll2,
};
static struct i2c_board_info __initdata beagle_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &beagle_twldata,
},
};
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
{
I2C_BOARD_INFO("eeprom", 0x50),
......@@ -470,8 +416,7 @@ static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
static int __init omap3_beagle_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, beagle_i2c_boardinfo,
ARRAY_SIZE(beagle_i2c_boardinfo));
omap3_pmic_init("twl4030", &beagle_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
......@@ -551,39 +496,6 @@ static struct platform_device *omap3_beagle_devices[] __initdata = {
&keys_gpio,
};
static void __init omap3beagle_flash_init(void)
{
u8 cs = 0;
u8 nandcs = GPMC_CS_NUM + 1;
/* find out the chip-select on which NAND exists */
while (cs < GPMC_CS_NUM) {
u32 ret = 0;
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
if ((ret & 0xC00) == 0x800) {
printk(KERN_INFO "Found NAND on CS%d\n", cs);
if (nandcs > GPMC_CS_NUM)
nandcs = cs;
}
cs++;
}
if (nandcs > GPMC_CS_NUM) {
printk(KERN_INFO "NAND: Unable to find configuration "
"in GPMC\n ");
return;
}
if (nandcs < GPMC_CS_NUM) {
omap3beagle_nand_data.cs = nandcs;
printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
if (gpmc_nand_init(&omap3beagle_nand_data) < 0)
printk(KERN_ERR "Unable to register NAND device\n");
}
}
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
......@@ -602,12 +514,6 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init beagle_opp_init(void)
{
int r = 0;
......@@ -665,13 +571,13 @@ static void __init omap3_beagle_init(void)
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
gpio_request(170, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(170, true);
gpio_request_one(170, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
omap3beagle_flash_init();
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
......
This diff is collapsed.
......@@ -37,6 +37,7 @@
#include "hsmmc.h"
#include "timer-gp.h"
#include "control.h"
#include "common-board-devices.h"
#include <plat/mux.h>
#include <plat/board.h>
......@@ -93,19 +94,9 @@ static struct twl4030_platform_data omap3logic_twldata = {
.vmmc1 = &omap3logic_vmmc1,
};
static struct i2c_board_info __initdata omap3logic_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &omap3logic_twldata,
},
};
static int __init omap3logic_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, omap3logic_i2c_boardinfo,
ARRAY_SIZE(omap3logic_i2c_boardinfo));
omap3_pmic_init("twl4030", &omap3logic_twldata);
return 0;
}
......@@ -147,7 +138,6 @@ static struct omap_smsc911x_platform_data __initdata board_smsc911x_data = {
.cs = OMAP3LOGIC_SMSC911X_CS,
.gpio_irq = -EINVAL,
.gpio_reset = -EINVAL,
.flags = IORESOURCE_IRQ_LOWLEVEL,
};
/* TODO/FIXME (comment by Peter Barada, LogicPD):
......
......@@ -22,7 +22,6 @@
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <linux/wl12xx.h>
......@@ -52,6 +51,7 @@
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define PANDORA_WIFI_IRQ_GPIO 21
#define PANDORA_WIFI_NRESET_GPIO 23
......@@ -305,24 +305,13 @@ static int omap3pandora_twl_gpio_setup(struct device *dev,
/* gpio + 13 drives 32kHz buffer for wifi module */
gpio_32khz = gpio + 13;
ret = gpio_request(gpio_32khz, "wifi 32kHz");
ret = gpio_request_one(gpio_32khz, GPIOF_OUT_INIT_HIGH, "wifi 32kHz");
if (ret < 0) {
pr_err("Cannot get GPIO line %d, ret=%d\n", gpio_32khz, ret);
goto fail;
}
ret = gpio_direction_output(gpio_32khz, 1);
if (ret < 0) {
pr_err("Cannot set GPIO line %d, ret=%d\n", gpio_32khz, ret);
goto fail_direction;
return -ENODEV;
}
return 0;
fail_direction:
gpio_free(gpio_32khz);
fail:
return -ENODEV;
}
static struct twl4030_gpio_platform_data omap3pandora_gpio_data = {
......@@ -544,15 +533,6 @@ static struct twl4030_platform_data omap3pandora_twldata = {
.bci = &pandora_bci_data,
};
static struct i2c_board_info __initdata omap3pandora_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("tps65950", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &omap3pandora_twldata,
},
};
static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
{
I2C_BOARD_INFO("bq27500", 0x55),
......@@ -562,61 +542,15 @@ static struct i2c_board_info __initdata omap3pandora_i2c3_boardinfo[] = {
static int __init omap3pandora_i2c_init(void)
{
omap_register_i2c_bus(1, 2600, omap3pandora_i2c_boardinfo,
ARRAY_SIZE(omap3pandora_i2c_boardinfo));
omap3_pmic_init("tps65950", &omap3pandora_twldata);
/* i2c2 pins are not connected */
omap_register_i2c_bus(3, 100, omap3pandora_i2c3_boardinfo,
ARRAY_SIZE(omap3pandora_i2c3_boardinfo));
return 0;
}
static void __init omap3pandora_ads7846_init(void)
{
int gpio = OMAP3_PANDORA_TS_GPIO;
int ret;
ret = gpio_request(gpio, "ads7846_pen_down");
if (ret < 0) {
printk(KERN_ERR "Failed to request GPIO %d for "
"ads7846 pen down IRQ\n", gpio);
return;
}
gpio_direction_input(gpio);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(OMAP3_PANDORA_TS_GPIO);
}
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info omap3pandora_spi_board_info[] __initdata = {
{
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_PANDORA_TS_GPIO),
.platform_data = &ads7846_config,
}, {
.modalias = "tpo_td043mtea1_panel_spi",
.bus_num = 1,
.chip_select = 1,
......@@ -639,14 +573,10 @@ static void __init pandora_wl1251_init(void)
memset(&pandora_wl1251_pdata, 0, sizeof(pandora_wl1251_pdata));
ret = gpio_request(PANDORA_WIFI_IRQ_GPIO, "wl1251 irq");
ret = gpio_request_one(PANDORA_WIFI_IRQ_GPIO, GPIOF_IN, "wl1251 irq");
if (ret < 0)
goto fail;
ret = gpio_direction_input(PANDORA_WIFI_IRQ_GPIO);
if (ret < 0)
goto fail_irq;
pandora_wl1251_pdata.irq = gpio_to_irq(PANDORA_WIFI_IRQ_GPIO);
if (pandora_wl1251_pdata.irq < 0)
goto fail_irq;
......@@ -688,12 +618,6 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init omap3pandora_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
......@@ -705,9 +629,9 @@ static void __init omap3pandora_init(void)
omap_serial_init();
spi_register_board_info(omap3pandora_spi_board_info,
ARRAY_SIZE(omap3pandora_spi_board_info));
omap3pandora_ads7846_init();
omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL);
usbhs_init(&usbhs_bdata);
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
gpmc_nand_init(&pandora_nand_data);
/* Ensure SDRC pins are mux'd for self-refresh */
......
......@@ -45,7 +45,6 @@
#include <plat/mcspi.h>
#include <linux/input/matrix_keypad.h>
#include <linux/spi/spi.h>
#include <linux/spi/ads7846.h>
#include <linux/interrupt.h>
#include <linux/smsc911x.h>
#include <linux/i2c/at24.h>
......@@ -54,52 +53,28 @@
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
#include "common-board-devices.h"
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <plat/gpmc-smsc911x.h>
#define OMAP3STALKER_ETHR_START 0x2c000000
#define OMAP3STALKER_ETHR_SIZE 1024
#define OMAP3STALKER_ETHR_GPIO_IRQ 19
#define OMAP3STALKER_SMC911X_CS 5
static struct resource omap3stalker_smsc911x_resources[] = {
[0] = {
.start = OMAP3STALKER_ETHR_START,
.end =
(OMAP3STALKER_ETHR_START + OMAP3STALKER_ETHR_SIZE - 1),
.flags = IORESOURCE_MEM,
},
[1] = {
.start = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
.end = OMAP_GPIO_IRQ(OMAP3STALKER_ETHR_GPIO_IRQ),
.flags = (IORESOURCE_IRQ | IRQF_TRIGGER_LOW),
},
};
static struct smsc911x_platform_config smsc911x_config = {
.phy_interface = PHY_INTERFACE_MODE_MII,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
static struct omap_smsc911x_platform_data smsc911x_cfg = {
.cs = OMAP3STALKER_SMC911X_CS,
.gpio_irq = OMAP3STALKER_ETHR_GPIO_IRQ,
.gpio_reset = -EINVAL,
.flags = (SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS),
};
static struct platform_device omap3stalker_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(omap3stalker_smsc911x_resources),
.resource = &omap3stalker_smsc911x_resources[0],
.dev = {
.platform_data = &smsc911x_config,
},
};
static inline void __init omap3stalker_init_eth(void)
{
int eth_cs;
struct clk *l3ck;
unsigned int rate;
eth_cs = OMAP3STALKER_SMC911X_CS;
l3ck = clk_get(NULL, "l3_ck");
if (IS_ERR(l3ck))
rate = 100000000;
......@@ -107,16 +82,7 @@ static inline void __init omap3stalker_init_eth(void)
rate = clk_get_rate(l3ck);
omap_mux_init_gpio(19, OMAP_PIN_INPUT_PULLUP);
if (gpio_request(OMAP3STALKER_ETHR_GPIO_IRQ, "SMC911x irq") < 0) {
printk(KERN_ERR
"Failed to request GPIO%d for smc911x IRQ\n",
OMAP3STALKER_ETHR_GPIO_IRQ);
return;
}
gpio_direction_input(OMAP3STALKER_ETHR_GPIO_IRQ);
platform_device_register(&omap3stalker_smsc911x_device);
gpmc_smsc911x_init(&smsc911x_cfg);
}
#else
......@@ -365,12 +331,11 @@ omap3stalker_twl_gpio_setup(struct device *dev,
*/
/* TWL4030_GPIO_MAX + 0 == ledA, LCD Backlight control */
gpio_request(gpio + TWL4030_GPIO_MAX, "EN_LCD_BKL");
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
"EN_LCD_BKL");
/* gpio + 7 == DVI Enable */
gpio_request(gpio + 7, "EN_DVI");
gpio_direction_output(gpio + 7, 0);
gpio_request_one(gpio + 7, GPIOF_OUT_INIT_LOW, "EN_DVI");
/* TWL4030_GPIO_MAX + 1 == ledB (out, mmc0) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
......@@ -489,15 +454,8 @@ static struct twl4030_platform_data omap3stalker_twldata = {
.codec = &omap3stalker_codec_data,
.vdac = &omap3_stalker_vdac,
.vpll2 = &omap3_stalker_vpll2,
};
static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &omap3stalker_twldata,
},
.vmmc1 = &omap3stalker_vmmc1,
.vsim = &omap3stalker_vsim,
};
static struct at24_platform_data fram_info = {
......@@ -516,15 +474,7 @@ static struct i2c_board_info __initdata omap3stalker_i2c_boardinfo3[] = {
static int __init omap3_stalker_i2c_init(void)
{
/*
* REVISIT: These entries can be set in omap3evm_twl_data
* after a merge with MFD tree
*/
omap3stalker_twldata.vmmc1 = &omap3stalker_vmmc1;
omap3stalker_twldata.vsim = &omap3stalker_vsim;
omap_register_i2c_bus(1, 2600, omap3stalker_i2c_boardinfo,
ARRAY_SIZE(omap3stalker_i2c_boardinfo));
omap3_pmic_init("twl4030", &omap3stalker_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, omap3stalker_i2c_boardinfo3,
ARRAY_SIZE(omap3stalker_i2c_boardinfo3));
......@@ -532,49 +482,6 @@ static int __init omap3_stalker_i2c_init(void)
}
#define OMAP3_STALKER_TS_GPIO 175
static void ads7846_dev_init(void)
{
if (gpio_request(OMAP3_STALKER_TS_GPIO, "ADS7846 pendown") < 0)
printk(KERN_ERR "can't get ads7846 pen down GPIO\n");
gpio_direction_input(OMAP3_STALKER_TS_GPIO);
gpio_set_debounce(OMAP3_STALKER_TS_GPIO, 310);
}
static int ads7846_get_pendown_state(void)
{
return !gpio_get_value(OMAP3_STALKER_TS_GPIO);
}
static struct ads7846_platform_data ads7846_config = {
.x_max = 0x0fff,
.y_max = 0x0fff,
.x_plate_ohms = 180,
.pressure_max = 255,
.debounce_max = 10,
.debounce_tol = 3,
.debounce_rep = 1,
.get_pendown_state = ads7846_get_pendown_state,
.keep_vref_on = 1,
.settle_delay_usecs = 150,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info omap3stalker_spi_board_info[] = {
[0] = {
.modalias = "ads7846",
.bus_num = 1,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_STALKER_TS_GPIO),
.platform_data = &ads7846_config,
},
};
static struct omap_board_config_kernel omap3_stalker_config[] __initdata = {
};
......@@ -618,12 +525,6 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init omap3_stalker_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
......@@ -636,13 +537,11 @@ static void __init omap3_stalker_init(void)
ARRAY_SIZE(omap3_stalker_devices));
omap_display_init(&omap3_stalker_dss_data);
spi_register_board_info(omap3stalker_spi_board_info,
ARRAY_SIZE(omap3stalker_spi_board_info));
omap_serial_init();
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
ads7846_dev_init();
omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL);
omap_mux_init_gpio(21, OMAP_PIN_OUTPUT);
omap_mux_init_gpio(18, OMAP_PIN_INPUT_PULLUP);
......
......@@ -52,6 +52,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "timer-gp.h"
#include "common-board-devices.h"
#include <asm/setup.h>
......@@ -95,15 +96,6 @@ static struct mtd_partition omap3touchbook_nand_partitions[] = {
},
};
static struct omap_nand_platform_data omap3touchbook_nand_data = {
.options = NAND_BUSWIDTH_16,
.parts = omap3touchbook_nand_partitions,
.nr_parts = ARRAY_SIZE(omap3touchbook_nand_partitions),
.dma_channel = -1, /* disable DMA in OMAP NAND driver */
.nand_setup = NULL,
.dev_ready = NULL,
};
#include "sdram-micron-mt46h32m32lf-6.h"
static struct omap2_hsmmc_info mmc[] = {
......@@ -154,13 +146,11 @@ static int touchbook_twl_gpio_setup(struct device *dev,
/* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
gpio_request(gpio + 1, "EHCI_nOC");
gpio_direction_input(gpio + 1);
gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC");
/* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, active low) */
gpio_request(gpio + TWL4030_GPIO_MAX, "nEN_USB_PWR");
gpio_direction_output(gpio + TWL4030_GPIO_MAX, 0);
gpio_request_one(gpio + TWL4030_GPIO_MAX, GPIOF_OUT_INIT_LOW,
"nEN_USB_PWR");
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
......@@ -273,15 +263,6 @@ static struct twl4030_platform_data touchbook_twldata = {
.vpll2 = &touchbook_vpll2,
};
static struct i2c_board_info __initdata touchbook_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl4030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &touchbook_twldata,
},
};
static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("bq27200", 0x55),
......@@ -291,8 +272,7 @@ static struct i2c_board_info __initdata touchBook_i2c_boardinfo[] = {
static int __init omap3_touchbook_i2c_init(void)
{
/* Standard TouchBook bus */
omap_register_i2c_bus(1, 2600, touchbook_i2c_boardinfo,
ARRAY_SIZE(touchbook_i2c_boardinfo));
omap3_pmic_init("twl4030", &touchbook_twldata);
/* Additional TouchBook bus */
omap_register_i2c_bus(3, 100, touchBook_i2c_boardinfo,
......@@ -301,19 +281,7 @@ static int __init omap3_touchbook_i2c_init(void)
return 0;
}
static void __init omap3_ads7846_init(void)
{
if (gpio_request(OMAP3_TS_GPIO, "ads7846_pen_down")) {
printk(KERN_ERR "Failed to request GPIO %d for "
"ads7846 pen down IRQ\n", OMAP3_TS_GPIO);
return;
}
gpio_direction_input(OMAP3_TS_GPIO);
gpio_set_debounce(OMAP3_TS_GPIO, 310);
}
static struct ads7846_platform_data ads7846_config = {
static struct ads7846_platform_data ads7846_pdata = {
.x_min = 100,
.y_min = 265,
.x_max = 3950,
......@@ -327,23 +295,6 @@ static struct ads7846_platform_data ads7846_config = {
.keep_vref_on = 1,
};
static struct omap2_mcspi_device_config ads7846_mcspi_config = {
.turbo_mode = 0,
.single_channel = 1, /* 0: slave, 1: master */
};
static struct spi_board_info omap3_ads7846_spi_board_info[] __initdata = {
{
.modalias = "ads7846",
.bus_num = 4,
.chip_select = 0,
.max_speed_hz = 1500000,
.controller_data = &ads7846_mcspi_config,
.irq = OMAP_GPIO_IRQ(OMAP3_TS_GPIO),
.platform_data = &ads7846_config,
}
};
static struct gpio_led gpio_leds[] = {
{
.name = "touchbook::usr0",
......@@ -434,39 +385,6 @@ static struct platform_device *omap3_touchbook_devices[] __initdata = {
&keys_gpio,
};
static void __init omap3touchbook_flash_init(void)
{
u8 cs = 0;
u8 nandcs = GPMC_CS_NUM + 1;
/* find out the chip-select on which NAND exists */
while (cs < GPMC_CS_NUM) {
u32 ret = 0;
ret = gpmc_cs_read_reg(cs, GPMC_CS_CONFIG1);
if ((ret & 0xC00) == 0x800) {
printk(KERN_INFO "Found NAND on CS%d\n", cs);
if (nandcs > GPMC_CS_NUM)
nandcs = cs;
}
cs++;
}
if (nandcs > GPMC_CS_NUM) {
printk(KERN_INFO "NAND: Unable to find configuration "
"in GPMC\n ");
return;
}
if (nandcs < GPMC_CS_NUM) {
omap3touchbook_nand_data.cs = nandcs;
printk(KERN_INFO "Registering NAND on CS%d\n", nandcs);
if (gpmc_nand_init(&omap3touchbook_nand_data) < 0)
printk(KERN_ERR "Unable to register NAND device\n");
}
}
static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
......@@ -481,15 +399,10 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
static void omap3_touchbook_poweroff(void)
{
int r;
int pwr_off = TB_KILL_POWER_GPIO;
r = gpio_request(TB_KILL_POWER_GPIO, "DVI reset");
if (r < 0) {
if (gpio_request_one(pwr_off, GPIOF_OUT_INIT_LOW, "DVI reset") < 0)
printk(KERN_ERR "Unable to get kill power GPIO\n");
return;
}
gpio_direction_output(TB_KILL_POWER_GPIO, 0);
}
static int __init early_touchbook_revision(char *p)
......@@ -501,12 +414,6 @@ static int __init early_touchbook_revision(char *p)
}
early_param("tbr", early_touchbook_revision);
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void __init omap3_touchbook_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
......@@ -521,17 +428,15 @@ static void __init omap3_touchbook_init(void)
omap_serial_init();
omap_mux_init_gpio(170, OMAP_PIN_INPUT);
gpio_request(176, "DVI_nPD");
/* REVISIT leave DVI powered down until it's needed ... */
gpio_direction_output(176, true);
gpio_request_one(176, GPIOF_OUT_INIT_HIGH, "DVI_nPD");
/* Touchscreen and accelerometer */
spi_register_board_info(omap3_ads7846_spi_board_info,
ARRAY_SIZE(omap3_ads7846_spi_board_info));
omap3_ads7846_init();
usb_musb_init(&musb_board_data);
omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata);
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
omap3touchbook_flash_init();
omap_nand_flash_init(NAND_BUSWIDTH_16, omap3touchbook_nand_partitions,
ARRAY_SIZE(omap3touchbook_nand_partitions));
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
......
......@@ -46,6 +46,7 @@
#include "hsmmc.h"
#include "control.h"
#include "mux.h"
#include "common-board-devices.h"
#define GPIO_HUB_POWER 1
#define GPIO_HUB_NRESET 62
......@@ -111,6 +112,11 @@ static const struct usbhs_omap_board_data usbhs_bdata __initconst = {
.reset_gpio_port[2] = -EINVAL
};
static struct gpio panda_ehci_gpios[] __initdata = {
{ GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" },
{ GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" },
};
static void __init omap4_ehci_init(void)
{
int ret;
......@@ -120,44 +126,27 @@ static void __init omap4_ehci_init(void)
phy_ref_clk = clk_get(NULL, "auxclk3_ck");
if (IS_ERR(phy_ref_clk)) {
pr_err("Cannot request auxclk3\n");
goto error1;
return;
}
clk_set_rate(phy_ref_clk, 19200000);
clk_enable(phy_ref_clk);
/* disable the power to the usb hub prior to init */
ret = gpio_request(GPIO_HUB_POWER, "hub_power");
/* disable the power to the usb hub prior to init and reset phy+hub */
ret = gpio_request_array(panda_ehci_gpios,
ARRAY_SIZE(panda_ehci_gpios));
if (ret) {
pr_err("Cannot request GPIO %d\n", GPIO_HUB_POWER);
goto error1;
pr_err("Unable to initialize EHCI power/reset\n");
return;
}
gpio_export(GPIO_HUB_POWER, 0);
gpio_direction_output(GPIO_HUB_POWER, 0);
gpio_set_value(GPIO_HUB_POWER, 0);
/* reset phy+hub */
ret = gpio_request(GPIO_HUB_NRESET, "hub_nreset");
if (ret) {
pr_err("Cannot request GPIO %d\n", GPIO_HUB_NRESET);
goto error2;
}
gpio_export(GPIO_HUB_POWER, 0);
gpio_export(GPIO_HUB_NRESET, 0);
gpio_direction_output(GPIO_HUB_NRESET, 0);
gpio_set_value(GPIO_HUB_NRESET, 0);
gpio_set_value(GPIO_HUB_NRESET, 1);
usbhs_init(&usbhs_bdata);
/* enable power to hub */
gpio_set_value(GPIO_HUB_POWER, 1);
return;
error2:
gpio_free(GPIO_HUB_POWER);
error1:
pr_err("Unable to initialize EHCI power/reset\n");
return;
}
static struct omap_musb_board_data musb_board_data = {
......@@ -408,15 +397,6 @@ static struct twl4030_platform_data omap4_panda_twldata = {
.usb = &omap4_usbphy_data,
};
static struct i2c_board_info __initdata omap4_panda_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl6030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = OMAP44XX_IRQ_SYS_1N,
.platform_data = &omap4_panda_twldata,
},
};
/*
* Display monitor features are burnt in their EEPROM as EDID data. The EEPROM
* is connected as I2C slave device, and can be accessed at address 0x50
......@@ -429,12 +409,7 @@ static struct i2c_board_info __initdata panda_i2c_eeprom[] = {
static int __init omap4_panda_i2c_init(void)
{
/*
* Phoenix Audio IC needs I2C1 to
* start with 400 KHz or less
*/
omap_register_i2c_bus(1, 400, omap4_panda_i2c_boardinfo,
ARRAY_SIZE(omap4_panda_i2c_boardinfo));
omap4_pmic_init("twl6030", &omap4_panda_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
/*
* Bus 3 is attached to the DVI port where devices like the pico DLP
......@@ -651,27 +626,19 @@ static void omap4_panda_hdmi_mux_init(void)
OMAP_PIN_INPUT_PULLUP);
}
static struct gpio panda_hdmi_gpios[] = {
{ HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_hpd" },
{ HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH, "hdmi_gpio_ls_oe" },
};
static int omap4_panda_panel_enable_hdmi(struct omap_dss_device *dssdev)
{
int status;
status = gpio_request_one(HDMI_GPIO_HPD, GPIOF_OUT_INIT_HIGH,
"hdmi_gpio_hpd");
if (status) {
pr_err("Cannot request GPIO %d\n", HDMI_GPIO_HPD);
return status;
}
status = gpio_request_one(HDMI_GPIO_LS_OE, GPIOF_OUT_INIT_HIGH,
"hdmi_gpio_ls_oe");
if (status) {
pr_err("Cannot request GPIO %d\n", HDMI_GPIO_LS_OE);
goto error1;
}
return 0;
error1:
gpio_free(HDMI_GPIO_HPD);
status = gpio_request_array(panda_hdmi_gpios,
ARRAY_SIZE(panda_hdmi_gpios));
if (status)
pr_err("Cannot request HDMI GPIOs\n");
return status;
}
......
This diff is collapsed.
......@@ -31,6 +31,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "sdram-nokia.h"
#include "common-board-devices.h"
static struct regulator_consumer_supply rm680_vemmc_consumers[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.1"),
......@@ -90,19 +91,9 @@ static struct twl4030_platform_data rm680_twl_data = {
/* add rest of the children here */
};
static struct i2c_board_info __initdata rm680_twl_i2c_board_info[] = {
{
I2C_BOARD_INFO("twl5031", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &rm680_twl_data,
},
};
static void __init rm680_i2c_init(void)
{
omap_register_i2c_bus(1, 2900, rm680_twl_i2c_board_info,
ARRAY_SIZE(rm680_twl_i2c_board_info));
omap_pmic_init(1, 2900, "twl5031", INT_34XX_SYS_NIRQ, &rm680_twl_data);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
}
......@@ -153,17 +144,11 @@ static struct omap_board_mux board_mux[] __initdata = {
};
#endif
static struct omap_musb_board_data rm680_musb_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_PERIPHERAL,
.power = 100,
};
static void __init rm680_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap_serial_init();
usb_musb_init(&rm680_musb_data);
usb_musb_init(NULL);
rm680_peripherals_init();
}
......
......@@ -43,6 +43,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define SYSTEM_REV_B_USES_VAUX3 0x1699
#define SYSTEM_REV_S_USES_VAUX3 0x8
......@@ -557,10 +558,8 @@ static __init void rx51_init_si4713(void)
static int rx51_twlgpio_setup(struct device *dev, unsigned gpio, unsigned n)
{
/* FIXME this gpio setup is just a placeholder for now */
gpio_request(gpio + 6, "backlight_pwm");
gpio_direction_output(gpio + 6, 0);
gpio_request(gpio + 7, "speaker_en");
gpio_direction_output(gpio + 7, 1);
gpio_request_one(gpio + 6, GPIOF_OUT_INIT_LOW, "backlight_pwm");
gpio_request_one(gpio + 7, GPIOF_OUT_INIT_HIGH, "speaker_en");
return 0;
}
......@@ -777,15 +776,6 @@ static struct tpa6130a2_platform_data rx51_tpa6130a2_data __initdata_or_module =
.power_gpio = 98,
};
static struct i2c_board_info __initdata rx51_peripherals_i2c_board_info_1[] = {
{
I2C_BOARD_INFO("twl5030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &rx51_twldata,
},
};
/* Audio setup data */
static struct aic3x_setup_data rx51_aic34_setup = {
.gpio_func[0] = AIC3X_GPIO1_FUNC_DISABLED,
......@@ -833,8 +823,7 @@ static int __init rx51_i2c_init(void)
rx51_twldata.vaux3 = &rx51_vaux3_cam;
}
rx51_twldata.vmmc2 = &rx51_vmmc2;
omap_register_i2c_bus(1, 2200, rx51_peripherals_i2c_board_info_1,
ARRAY_SIZE(rx51_peripherals_i2c_board_info_1));
omap_pmic_init(1, 2200, "twl5030", INT_34XX_SYS_NIRQ, &rx51_twldata);
omap_register_i2c_bus(2, 100, rx51_peripherals_i2c_board_info_2,
ARRAY_SIZE(rx51_peripherals_i2c_board_info_2));
omap_register_i2c_bus(3, 400, NULL, 0);
......@@ -921,26 +910,20 @@ static void rx51_wl1251_set_power(bool enable)
gpio_set_value(RX51_WL1251_POWER_GPIO, enable);
}
static struct gpio rx51_wl1251_gpios[] __initdata = {
{ RX51_WL1251_POWER_GPIO, GPIOF_OUT_INIT_LOW, "wl1251 power" },
{ RX51_WL1251_IRQ_GPIO, GPIOF_IN, "wl1251 irq" },
};
static void __init rx51_init_wl1251(void)
{
int irq, ret;
ret = gpio_request(RX51_WL1251_POWER_GPIO, "wl1251 power");
ret = gpio_request_array(rx51_wl1251_gpios,
ARRAY_SIZE(rx51_wl1251_gpios));
if (ret < 0)
goto error;
ret = gpio_direction_output(RX51_WL1251_POWER_GPIO, 0);
if (ret < 0)
goto err_power;
ret = gpio_request(RX51_WL1251_IRQ_GPIO, "wl1251 irq");
if (ret < 0)
goto err_power;
ret = gpio_direction_input(RX51_WL1251_IRQ_GPIO);
if (ret < 0)
goto err_irq;
irq = gpio_to_irq(RX51_WL1251_IRQ_GPIO);
if (irq < 0)
goto err_irq;
......@@ -952,10 +935,7 @@ static void __init rx51_init_wl1251(void)
err_irq:
gpio_free(RX51_WL1251_IRQ_GPIO);
err_power:
gpio_free(RX51_WL1251_POWER_GPIO);
error:
printk(KERN_ERR "wl1251 board initialisation failed\n");
wl1251_pdata.set_power = NULL;
......
......@@ -76,13 +76,12 @@ static int __init rx51_video_init(void)
return 0;
}
if (gpio_request(RX51_LCD_RESET_GPIO, "LCD ACX565AKM reset")) {
if (gpio_request_one(RX51_LCD_RESET_GPIO, GPIOF_OUT_INIT_HIGH,
"LCD ACX565AKM reset")) {
pr_err("%s failed to get LCD Reset GPIO\n", __func__);
return 0;
}
gpio_direction_output(RX51_LCD_RESET_GPIO, 1);
omap_display_init(&rx51_dss_board_info);
return 0;
}
......
......@@ -58,21 +58,25 @@ static struct platform_device leds_gpio = {
},
};
/*
* cpuidle C-states definition override from the default values.
* The 'exit_latency' field is the sum of sleep and wake-up latencies.
*/
static struct cpuidle_params rx51_cpuidle_params[] = {
/* C1 */
{1, 110, 162, 5},
{110 + 162, 5 , 1},
/* C2 */
{1, 106, 180, 309},
{106 + 180, 309, 1},
/* C3 */
{0, 107, 410, 46057},
{107 + 410, 46057, 0},
/* C4 */
{0, 121, 3374, 46057},
{121 + 3374, 46057, 0},
/* C5 */
{1, 855, 1146, 46057},
{855 + 1146, 46057, 1},
/* C6 */
{0, 7580, 4134, 484329},
{7580 + 4134, 484329, 0},
/* C7 */
{1, 7505, 15274, 484329},
{7505 + 15274, 484329, 1},
};
static struct omap_lcd_config rx51_lcd_config = {
......
......@@ -15,6 +15,7 @@
#include <linux/interrupt.h>
#include <plat/gpmc.h>
#include <plat/gpmc-smsc911x.h>
#include <mach/board-zoom.h>
......@@ -26,60 +27,16 @@
#define DEBUG_BASE 0x08000000
#define ZOOM_ETHR_START DEBUG_BASE
static struct resource zoom_smsc911x_resources[] = {
[0] = {
.start = ZOOM_ETHR_START,
.end = ZOOM_ETHR_START + SZ_4K,
.flags = IORESOURCE_MEM,
},
[1] = {
.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL,
},
};
static struct smsc911x_platform_config zoom_smsc911x_config = {
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW,
.irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN,
static struct omap_smsc911x_platform_data zoom_smsc911x_cfg = {
.cs = ZOOM_SMSC911X_CS,
.gpio_irq = ZOOM_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct platform_device zoom_smsc911x_device = {
.name = "smsc911x",
.id = -1,
.num_resources = ARRAY_SIZE(zoom_smsc911x_resources),
.resource = zoom_smsc911x_resources,
.dev = {
.platform_data = &zoom_smsc911x_config,
},
};
static inline void __init zoom_init_smsc911x(void)
{
int eth_cs;
unsigned long cs_mem_base;
int eth_gpio = 0;
eth_cs = ZOOM_SMSC911X_CS;
if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n");
return;
}
zoom_smsc911x_resources[0].start = cs_mem_base + 0x0;
zoom_smsc911x_resources[0].end = cs_mem_base + 0xff;
eth_gpio = ZOOM_SMSC911X_GPIO;
zoom_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio);
if (gpio_request(eth_gpio, "smsc911x irq") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n",
eth_gpio);
return;
}
gpio_direction_input(eth_gpio);
gpmc_smsc911x_init(&zoom_smsc911x_cfg);
}
static struct plat_serial8250_port serial_platform_data[] = {
......@@ -120,12 +77,9 @@ static inline void __init zoom_init_quaduart(void)
quart_gpio = ZOOM_QUADUART_GPIO;
if (gpio_request(quart_gpio, "TL16CP754C GPIO") < 0) {
if (gpio_request_one(quart_gpio, GPIOF_IN, "TL16CP754C GPIO") < 0)
printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n",
quart_gpio);
return;
}
gpio_direction_input(quart_gpio);
}
static inline int omap_zoom_debugboard_detect(void)
......@@ -135,12 +89,12 @@ static inline int omap_zoom_debugboard_detect(void)
debug_board_detect = ZOOM_SMSC911X_GPIO;
if (gpio_request(debug_board_detect, "Zoom debug board detect") < 0) {
if (gpio_request_one(debug_board_detect, GPIOF_IN,
"Zoom debug board detect") < 0) {
printk(KERN_ERR "Failed to request GPIO%d for Zoom debug"
"board detect\n", debug_board_detect);
return 0;
}
gpio_direction_input(debug_board_detect);
if (!gpio_get_value(debug_board_detect)) {
ret = 0;
......@@ -150,7 +104,6 @@ static inline int omap_zoom_debugboard_detect(void)
}
static struct platform_device *zoom_devices[] __initdata = {
&zoom_smsc911x_device,
&zoom_debugboard_serial_device,
};
......
......@@ -21,34 +21,19 @@
#define LCD_PANEL_RESET_GPIO_PILOT 55
#define LCD_PANEL_QVGA_GPIO 56
static struct gpio zoom_lcd_gpios[] __initdata = {
{ -EINVAL, GPIOF_OUT_INIT_HIGH, "lcd reset" },
{ LCD_PANEL_QVGA_GPIO, GPIOF_OUT_INIT_HIGH, "lcd qvga" },
};
static void zoom_lcd_panel_init(void)
{
int ret;
unsigned char lcd_panel_reset_gpio;
lcd_panel_reset_gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
zoom_lcd_gpios[0].gpio = (omap_rev() > OMAP3430_REV_ES3_0) ?
LCD_PANEL_RESET_GPIO_PROD :
LCD_PANEL_RESET_GPIO_PILOT;
ret = gpio_request(lcd_panel_reset_gpio, "lcd reset");
if (ret) {
pr_err("Failed to get LCD reset GPIO (gpio%d).\n",
lcd_panel_reset_gpio);
return;
}
gpio_direction_output(lcd_panel_reset_gpio, 1);
ret = gpio_request(LCD_PANEL_QVGA_GPIO, "lcd qvga");
if (ret) {
pr_err("Failed to get LCD_PANEL_QVGA_GPIO (gpio%d).\n",
LCD_PANEL_QVGA_GPIO);
goto err0;
}
gpio_direction_output(LCD_PANEL_QVGA_GPIO, 1);
return;
err0:
gpio_free(lcd_panel_reset_gpio);
if (gpio_request_array(zoom_lcd_gpios, ARRAY_SIZE(zoom_lcd_gpios)))
pr_err("%s: Failed to get LCD GPIOs.\n", __func__);
}
static int zoom_panel_enable_lcd(struct omap_dss_device *dssdev)
......
......@@ -31,6 +31,7 @@
#include "mux.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define OMAP_ZOOM_WLAN_PMENA_GPIO (101)
#define OMAP_ZOOM_WLAN_IRQ_GPIO (162)
......@@ -276,13 +277,11 @@ static int zoom_twl_gpio_setup(struct device *dev,
zoom_vsim_supply.dev = mmc[0].dev;
zoom_vmmc2_supply.dev = mmc[1].dev;
ret = gpio_request(LCD_PANEL_ENABLE_GPIO, "lcd enable");
if (ret) {
ret = gpio_request_one(LCD_PANEL_ENABLE_GPIO, GPIOF_OUT_INIT_LOW,
"lcd enable");
if (ret)
pr_err("Failed to get LCD_PANEL_ENABLE_GPIO (gpio%d).\n",
LCD_PANEL_ENABLE_GPIO);
return ret;
}
gpio_direction_output(LCD_PANEL_ENABLE_GPIO, 0);
return ret;
}
......@@ -349,15 +348,6 @@ static struct twl4030_platform_data zoom_twldata = {
.vdac = &zoom_vdac,
};
static struct i2c_board_info __initdata zoom_i2c_boardinfo[] = {
{
I2C_BOARD_INFO("twl5030", 0x48),
.flags = I2C_CLIENT_WAKE,
.irq = INT_34XX_SYS_NIRQ,
.platform_data = &zoom_twldata,
},
};
static int __init omap_i2c_init(void)
{
if (machine_is_omap_zoom2()) {
......@@ -365,19 +355,12 @@ static int __init omap_i2c_init(void)
zoom_audio_data.hs_extmute = 1;
zoom_audio_data.set_hs_extmute = zoom2_set_hs_extmute;
}
omap_register_i2c_bus(1, 2400, zoom_i2c_boardinfo,
ARRAY_SIZE(zoom_i2c_boardinfo));
omap_pmic_init(1, 2400, "twl5030", INT_34XX_SYS_NIRQ, &zoom_twldata);
omap_register_i2c_bus(2, 400, NULL, 0);
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct omap_musb_board_data musb_board_data = {
.interface_type = MUSB_INTERFACE_ULPI,
.mode = MUSB_OTG,
.power = 100,
};
static void enable_board_wakeup_source(void)
{
/* T2 interrupt line (keypad) */
......@@ -392,7 +375,7 @@ void __init zoom_peripherals_init(void)
omap_i2c_init();
platform_device_register(&omap_vwlan_device);
usb_musb_init(&musb_board_data);
usb_musb_init(NULL);
enable_board_wakeup_source();
omap_serial_init();
}
This diff is collapsed.
#ifndef __OMAP_COMMON_BOARD_DEVICES__
#define __OMAP_COMMON_BOARD_DEVICES__
struct twl4030_platform_data;
struct mtd_partition;
void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
struct twl4030_platform_data *pmic_data);
static inline void omap2_pmic_init(const char *pmic_type,
struct twl4030_platform_data *pmic_data)
{
omap_pmic_init(2, 2600, pmic_type, INT_24XX_SYS_NIRQ, pmic_data);
}
static inline void omap3_pmic_init(const char *pmic_type,
struct twl4030_platform_data *pmic_data)
{
omap_pmic_init(1, 2600, pmic_type, INT_34XX_SYS_NIRQ, pmic_data);
}
static inline void omap4_pmic_init(const char *pmic_type,
struct twl4030_platform_data *pmic_data)
{
/* Phoenix Audio IC needs I2C1 to start with 400 KHz or less */
omap_pmic_init(1, 400, pmic_type, OMAP44XX_IRQ_SYS_1N, pmic_data);
}
struct ads7846_platform_data;
void omap_ads7846_init(int bus_num, int gpio_pendown, int gpio_debounce,
struct ads7846_platform_data *board_pdata);
void omap_nand_flash_init(int opts, struct mtd_partition *parts, int n_parts);
#endif /* __OMAP_COMMON_BOARD_DEVICES__ */
This diff is collapsed.
......@@ -147,25 +147,24 @@ void __init gpmc_smc91x_init(struct omap_smc91x_platform_data *board_data)
goto free1;
}
if (gpio_request(gpmc_cfg->gpio_irq, "SMC91X irq") < 0)
if (gpio_request_one(gpmc_cfg->gpio_irq, GPIOF_IN, "SMC91X irq") < 0)
goto free1;
gpio_direction_input(gpmc_cfg->gpio_irq);
gpmc_smc91x_resources[1].start = gpio_to_irq(gpmc_cfg->gpio_irq);
if (gpmc_cfg->gpio_pwrdwn) {
ret = gpio_request(gpmc_cfg->gpio_pwrdwn, "SMC91X powerdown");
ret = gpio_request_one(gpmc_cfg->gpio_pwrdwn,
GPIOF_OUT_INIT_LOW, "SMC91X powerdown");
if (ret)
goto free2;
gpio_direction_output(gpmc_cfg->gpio_pwrdwn, 0);
}
if (gpmc_cfg->gpio_reset) {
ret = gpio_request(gpmc_cfg->gpio_reset, "SMC91X reset");
ret = gpio_request_one(gpmc_cfg->gpio_reset,
GPIOF_OUT_INIT_LOW, "SMC91X reset");
if (ret)
goto free3;
gpio_direction_output(gpmc_cfg->gpio_reset, 0);
gpio_set_value(gpmc_cfg->gpio_reset, 1);
msleep(100);
gpio_set_value(gpmc_cfg->gpio_reset, 0);
......
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
......@@ -105,13 +105,11 @@ static int __init omap4_pm_init(void)
pr_err("Power Management for TI OMAP4.\n");
#ifdef CONFIG_PM
ret = pwrdm_for_each(pwrdms_setup, NULL);
if (ret) {
pr_err("Failed to setup powerdomains\n");
goto err2;
}
#endif
#ifdef CONFIG_SUSPEND
suspend_set_ops(&omap_pm_ops);
......
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
This diff is collapsed.
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment