Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull arm-soc device tree conversions (part 2) from Olof Johansson:
 "These continue the device tree work from part 1, this set is for the
  tegra, mxs and imx platforms, all of which have dependencies on clock
  or pinctrl changes submitted earlier."

Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
  ARM: dt: tegra: invert status=disable vs status=okay
  ARM: dt: tegra: consistent basic property ordering
  ARM: dt: tegra: sort nodes based on bus order
  ARM: dt: tegra: remove duplicate device_type property
  ARM: dt: tegra: consistenly use lower-case for hex constants
  ARM: dt: tegra: format regs properties consistently
  ARM: dt: tegra: gpio comment cleanup
  ARM: dt: tegra: remove unnecessary unit addresses
  ARM: dt: tegra: whitespace cleanup
  ARM: dt: tegra cardhu: fix typo in SDHCI node name
  ARM: dt: tegra: cardhu: register core regulator tps62361
  ARM: dt: tegra30.dtsi: Add SMMU node
  ARM: dt: tegra20.dtsi: Add GART node
  ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
  ARM: dt: tegra: Add device tree support for AHB
  ARM: dts: enable audio support for imx28-evk
  ARM: dts: enable i2c device for imx28-evk
  i2c: mxs: add device tree probe support
  ARM: dts: enable mmc for imx28-evk
  ...

Documentation/devicetree/bindings/arm/fsl.txt

 Freescale i.MX Platforms Device Tree Bindings
 -----------------------------------------------
 
+i.MX23 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx23-evk", "fsl,imx23";
+
+i.MX28 Evaluation Kit
+Required root node properties:
+    - compatible = "fsl,imx28-evk", "fsl,imx28";
+
 i.MX51 Babbage Board
 Required root node properties:
     - compatible = "fsl,imx51-babbage", "fsl,imx51";
@@ -29,6 +37,10 @@ i.MX6 Quad SABRE Lite Board
 Required root node properties:
     - compatible = "fsl,imx6q-sabrelite", "fsl,imx6q";
 
+i.MX6 Quad SABRE Smart Device Board
+Required root node properties:
+    - compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+
 Generic i.MX boards
 -------------------
 

Documentation/devicetree/bindings/dma/fsl-mxs-dma.txt

+* Freescale MXS DMA
+
+Required properties:
+- compatible : Should be "fsl,<chip>-dma-apbh" or "fsl,<chip>-dma-apbx"
+- reg : Should contain registers location and length
+
+Supported chips:
+imx23, imx28.
+
+Examples:
+dma-apbh@80004000 {
+	compatible = "fsl,imx28-dma-apbh";
+	reg = <0x80004000 2000>;
+};
+
+dma-apbx@80024000 {
+	compatible = "fsl,imx28-dma-apbx";
+	reg = <0x80024000 2000>;
+};

Documentation/devicetree/bindings/gpio/gpio-mxs.txt

+* Freescale MXS GPIO controller
+
+The Freescale MXS GPIO controller is part of MXS PIN controller.  The
+GPIOs are organized in port/bank.  Each port consists of 32 GPIOs.
+
+As the GPIO controller is embedded in the PIN controller and all the
+GPIO ports share the same IO space with PIN controller, the GPIO node
+will be represented as sub-nodes of MXS pinctrl node.
+
+Required properties for GPIO node:
+- compatible : Should be "fsl,<soc>-gpio".  The supported SoCs include
+  imx23 and imx28.
+- interrupts : Should be the port interrupt shared by all 32 pins.
+- gpio-controller : Marks the device node as a gpio controller.
+- #gpio-cells : Should be two.  The first cell is the pin number and
+  the second cell is used to specify optional parameters (currently
+  unused).
+- interrupt-controller: Marks the device node as an interrupt controller.
+- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
+  The second cell bits[3:0] is used to specify trigger type and level flags:
+      1 = low-to-high edge triggered.
+      2 = high-to-low edge triggered.
+      4 = active high level-sensitive.
+      8 = active low level-sensitive.
+
+Note: Each GPIO port should have an alias correctly numbered in "aliases"
+node.
+
+Examples:
+
+aliases {
+	gpio0 = &gpio0;
+	gpio1 = &gpio1;
+	gpio2 = &gpio2;
+	gpio3 = &gpio3;
+	gpio4 = &gpio4;
+};
+
+pinctrl@80018000 {
+	compatible = "fsl,imx28-pinctrl", "simple-bus";
+	reg = <0x80018000 2000>;
+
+	gpio0: gpio@0 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <127>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio1: gpio@1 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <126>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio2: gpio@2 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <125>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio3: gpio@3 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <124>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+
+	gpio4: gpio@4 {
+		compatible = "fsl,imx28-gpio";
+		interrupts = <123>;
+		gpio-controller;
+		#gpio-cells = <2>;
+		interrupt-controller;
+		#interrupt-cells = <2>;
+	};
+};

Documentation/devicetree/bindings/i2c/i2c-mxs.txt

+* Freescale MXS Inter IC (I2C) Controller
+
+Required properties:
+- compatible: Should be "fsl,<chip>-i2c"
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+
+Examples:
+
+i2c0: i2c@80058000 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+	compatible = "fsl,imx28-i2c";
+	reg = <0x80058000 2000>;
+	interrupts = <111 68>;
+};

Documentation/devicetree/bindings/mmc/mxs-mmc.txt

+* Freescale MXS MMC controller
+
+The Freescale MXS Synchronous Serial Ports (SSP) can act as a MMC controller
+to support MMC, SD, and SDIO types of memory cards.
+
+Required properties:
+- compatible: Should be "fsl,<chip>-mmc".  The supported chips include
+  imx23 and imx28.
+- reg: Should contain registers location and length
+- interrupts: Should contain ERROR and DMA interrupts
+- fsl,ssp-dma-channel: APBH DMA channel for the SSP
+- bus-width: Number of data lines, can be <1>, <4>, or <8>
+
+Optional properties:
+- wp-gpios: Specify GPIOs for write protection
+
+Examples:
+
+ssp0: ssp@80010000 {
+	compatible = "fsl,imx28-mmc";
+	reg = <0x80010000 2000>;
+	interrupts = <96 82>;
+	fsl,ssp-dma-channel = <0>;
+	bus-width = <8>;
+};

Documentation/devicetree/bindings/net/fsl-fec.txt

@@ -14,7 +14,7 @@ Optional properties:
 
 Example:
 
-fec@83fec000 {
+ethernet@83fec000 {
 	compatible = "fsl,imx51-fec", "fsl,imx27-fec";
 	reg = <0x83fec000 0x4000>;
 	interrupts = <87>;

Documentation/devicetree/bindings/tty/serial/fsl-imx-uart.txt

@@ -11,7 +11,7 @@ Optional properties:
 
 Example:
 
-uart@73fbc000 {
+serial@73fbc000 {
 	compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 	reg = <0x73fbc000 0x4000>;
 	interrupts = <31>;

arch/arm/Kconfig

@@ -459,6 +459,7 @@ config ARCH_MXS
 	select COMMON_CLK
 	select HAVE_CLK_PREPARE
 	select PINCTRL
+	select USE_OF
 	help
 	  Support for Freescale MXS-based family of processors
 

arch/arm/Kconfig.debug

@@ -209,6 +209,14 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX50 or i.MX53.
 
+	config DEBUG_IMX6Q_UART2
+		bool "i.MX6Q Debug UART2"
+		depends on SOC_IMX6Q
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on i.MX6Q UART2. This is correct for e.g. the SabreLite
+                  board.
+
 	config DEBUG_IMX6Q_UART4
 		bool "i.MX6Q Debug UART4"
 		depends on SOC_IMX6Q

arch/arm/boot/dts/imx23-evk.dts

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx23.dtsi"
+
+/ {
+	model = "Freescale i.MX23 Evaluation Kit";
+	compatible = "fsl,imx23-evk", "fsl,imx23";
+
+	memory {
+		reg = <0x40000000 0x08000000>;
+	};
+
+	apb@80000000 {
+		apbh@80000000 {
+			ssp0: ssp@80010000 {
+				compatible = "fsl,imx23-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_8bit_pins_a &mmc0_pins_fixup>;
+				bus-width = <8>;
+				wp-gpios = <&gpio1 30 0>;
+				status = "okay";
+			};
+		};
+
+		apbx@80040000 {
+			duart: serial@80070000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/imx23.dtsi

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&icoll>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm926ejs";
+		};
+	};
+
+	apb@80000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x80000000 0x80000>;
+		ranges;
+
+		apbh@80000000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x80000000 0x40000>;
+			ranges;
+
+			icoll: interrupt-controller@80000000 {
+				compatible = "fsl,imx23-icoll", "fsl,mxs-icoll";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				reg = <0x80000000 0x2000>;
+			};
+
+			dma-apbh@80004000 {
+				compatible = "fsl,imx23-dma-apbh";
+				reg = <0x80004000 2000>;
+			};
+
+			ecc@80008000 {
+				reg = <0x80008000 2000>;
+				status = "disabled";
+			};
+
+			bch@8000a000 {
+				reg = <0x8000a000 2000>;
+				status = "disabled";
+			};
+
+			gpmi@8000c000 {
+				reg = <0x8000c000 2000>;
+				status = "disabled";
+			};
+
+			ssp0: ssp@80010000 {
+				reg = <0x80010000 2000>;
+				interrupts = <15 14>;
+				fsl,ssp-dma-channel = <1>;
+				status = "disabled";
+			};
+
+			etm@80014000 {
+				reg = <0x80014000 2000>;
+				status = "disabled";
+			};
+
+			pinctrl@80018000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx23-pinctrl", "simple-bus";
+				reg = <0x80018000 2000>;
+
+				gpio0: gpio@0 {
+					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					interrupts = <16>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio1: gpio@1 {
+					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					interrupts = <17>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio2: gpio@2 {
+					compatible = "fsl,imx23-gpio", "fsl,mxs-gpio";
+					interrupts = <18>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				duart_pins_a: duart@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x11a2 0x11b2>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mmc0_8bit_pins_a: mmc0-8bit@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x2020 0x2030 0x2040
+						0x2050 0x0082 0x0092 0x00a2
+						0x00b2 0x2000 0x2010 0x2060>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				mmc0_pins_fixup: mmc0-pins-fixup {
+					fsl,pinmux-ids = <0x2010 0x2060>;
+					fsl,pull-up = <0>;
+				};
+			};
+
+			digctl@8001c000 {
+				reg = <0x8001c000 2000>;
+				status = "disabled";
+			};
+
+			emi@80020000 {
+				reg = <0x80020000 2000>;
+				status = "disabled";
+			};
+
+			dma-apbx@80024000 {
+				compatible = "fsl,imx23-dma-apbx";
+				reg = <0x80024000 2000>;
+			};
+
+			dcp@80028000 {
+				reg = <0x80028000 2000>;
+				status = "disabled";
+			};
+
+			pxp@8002a000 {
+				reg = <0x8002a000 2000>;
+				status = "disabled";
+			};
+
+			ocotp@8002c000 {
+				reg = <0x8002c000 2000>;
+				status = "disabled";
+			};
+
+			axi-ahb@8002e000 {
+				reg = <0x8002e000 2000>;
+				status = "disabled";
+			};
+
+			lcdif@80030000 {
+				reg = <0x80030000 2000>;
+				status = "disabled";
+			};
+
+			ssp1: ssp@80034000 {
+				reg = <0x80034000 2000>;
+				interrupts = <2 20>;
+				fsl,ssp-dma-channel = <2>;
+				status = "disabled";
+			};
+
+			tvenc@80038000 {
+				reg = <0x80038000 2000>;
+				status = "disabled";
+			};
+                };
+
+		apbx@80040000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x80040000 0x40000>;
+			ranges;
+
+			clkctl@80040000 {
+				reg = <0x80040000 2000>;
+				status = "disabled";
+			};
+
+			saif0: saif@80042000 {
+				reg = <0x80042000 2000>;
+				status = "disabled";
+			};
+
+			power@80044000 {
+				reg = <0x80044000 2000>;
+				status = "disabled";
+			};
+
+			saif1: saif@80046000 {
+				reg = <0x80046000 2000>;
+				status = "disabled";
+			};
+
+			audio-out@80048000 {
+				reg = <0x80048000 2000>;
+				status = "disabled";
+			};
+
+			audio-in@8004c000 {
+				reg = <0x8004c000 2000>;
+				status = "disabled";
+			};
+
+			lradc@80050000 {
+				reg = <0x80050000 2000>;
+				status = "disabled";
+			};
+
+			spdif@80054000 {
+				reg = <0x80054000 2000>;
+				status = "disabled";
+			};
+
+			i2c@80058000 {
+				reg = <0x80058000 2000>;
+				status = "disabled";
+			};
+
+			rtc@8005c000 {
+				reg = <0x8005c000 2000>;
+				status = "disabled";
+			};
+
+			pwm@80064000 {
+				reg = <0x80064000 2000>;
+				status = "disabled";
+			};
+
+			timrot@80068000 {
+				reg = <0x80068000 2000>;
+				status = "disabled";
+			};
+
+			auart0: serial@8006c000 {
+				reg = <0x8006c000 0x2000>;
+				status = "disabled";
+			};
+
+			auart1: serial@8006e000 {
+				reg = <0x8006e000 0x2000>;
+				status = "disabled";
+			};
+
+			duart: serial@80070000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x80070000 0x2000>;
+				interrupts = <0>;
+				status = "disabled";
+			};
+
+			usbphy@8007c000 {
+				reg = <0x8007c000 0x2000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x80080000 0x80000>;
+		ranges;
+
+		usbctrl@80080000 {
+			reg = <0x80080000 0x10000>;
+			status = "disabled";
+		};
+	};
+};

arch/arm/boot/dts/imx27-phytec-phycore.dts

@@ -27,22 +27,22 @@ wdog@10002000 {
 				status = "okay";
 			};
 
-			uart@1000a000 {
+			serial@1000a000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
-			uart@1000b000 {
+			serial@1000b000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
-			uart@1000c000 {
+			serial@1000c000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
-			fec@1002b000 {
+			ethernet@1002b000 {
 				status = "okay";
 			};
 

arch/arm/boot/dts/imx27.dtsi

@@ -59,28 +59,28 @@ wdog@10002000 {
 				status = "disabled";
 			};
 
-			uart1: uart@1000a000 {
+			uart1: serial@1000a000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1000a000 0x1000>;
 				interrupts = <20>;
 				status = "disabled";
 			};
 
-			uart2: uart@1000b000 {
+			uart2: serial@1000b000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1000b000 0x1000>;
 				interrupts = <19>;
 				status = "disabled";
 			};
 
-			uart3: uart@1000c000 {
+			uart3: serial@1000c000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1000c000 0x1000>;
 				interrupts = <18>;
 				status = "disabled";
 			};
 
-			uart4: uart@1000d000 {
+			uart4: serial@1000d000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1000d000 0x1000>;
 				interrupts = <17>;
@@ -183,14 +183,14 @@ cspi3: cspi@10017000 {
 				status = "disabled";
 			};
 
-			uart5: uart@1001b000 {
+			uart5: serial@1001b000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1001b000 0x1000>;
 				interrupts = <49>;
 				status = "disabled";
 			};
 
-			uart6: uart@1001c000 {
+			uart6: serial@1001c000 {
 				compatible = "fsl,imx27-uart", "fsl,imx21-uart";
 				reg = <0x1001c000 0x1000>;
 				interrupts = <48>;
@@ -206,7 +206,7 @@ i2c2: i2c@1001d000 {
 				status = "disabled";
 			};
 
-			fec: fec@1002b000 {
+			fec: ethernet@1002b000 {
 				compatible = "fsl,imx27-fec";
 				reg = <0x1002b000 0x4000>;
 				interrupts = <50>;

arch/arm/boot/dts/imx28-evk.dts

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx28.dtsi"
+
+/ {
+	model = "Freescale i.MX28 Evaluation Kit";
+	compatible = "fsl,imx28-evk", "fsl,imx28";
+
+	memory {
+		reg = <0x40000000 0x08000000>;
+	};
+
+	apb@80000000 {
+		apbh@80000000 {
+			ssp0: ssp@80010000 {
+				compatible = "fsl,imx28-mmc";
+				pinctrl-names = "default";
+				pinctrl-0 = <&mmc0_8bit_pins_a
+					&mmc0_cd_cfg &mmc0_sck_cfg>;
+				bus-width = <8>;
+				wp-gpios = <&gpio2 12 0>;
+				status = "okay";
+			};
+
+			ssp1: ssp@80012000 {
+				compatible = "fsl,imx28-mmc";
+				bus-width = <8>;
+				wp-gpios = <&gpio0 28 0>;
+				status = "okay";
+			};
+		};
+
+		apbx@80040000 {
+			saif0: saif@80042000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&saif0_pins_a>;
+				status = "okay";
+			};
+
+			saif1: saif@80046000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&saif1_pins_a>;
+				fsl,saif-master = <&saif0>;
+				status = "okay";
+			};
+
+			i2c0: i2c@80058000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&i2c0_pins_a>;
+				status = "okay";
+
+				sgtl5000: codec@0a {
+					compatible = "fsl,sgtl5000";
+					reg = <0x0a>;
+					VDDA-supply = <&reg_3p3v>;
+					VDDIO-supply = <&reg_3p3v>;
+
+				};
+			};
+
+			duart: serial@80074000 {
+				pinctrl-names = "default";
+				pinctrl-0 = <&duart_pins_a>;
+				status = "okay";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		mac0: ethernet@800f0000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac0_pins_a>;
+			status = "okay";
+		};
+
+		mac1: ethernet@800f4000 {
+			phy-mode = "rmii";
+			pinctrl-names = "default";
+			pinctrl-0 = <&mac1_pins_a>;
+			status = "okay";
+		};
+	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p3v: 3p3v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P3V";
+			regulator-min-microvolt = <3300000>;
+			regulator-max-microvolt = <3300000>;
+			regulator-always-on;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx28-evk-sgtl5000",
+			     "fsl,mxs-audio-sgtl5000";
+		model = "imx28-evk-sgtl5000";
+		saif-controllers = <&saif0 &saif1>;
+		audio-codec = <&sgtl5000>;
+	};
+};

arch/arm/boot/dts/imx28.dtsi

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+	interrupt-parent = <&icoll>;
+
+	aliases {
+		gpio0 = &gpio0;
+		gpio1 = &gpio1;
+		gpio2 = &gpio2;
+		gpio3 = &gpio3;
+		gpio4 = &gpio4;
+		saif0 = &saif0;
+		saif1 = &saif1;
+	};
+
+	cpus {
+		cpu@0 {
+			compatible = "arm,arm926ejs";
+		};
+	};
+
+	apb@80000000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x80000000 0x80000>;
+		ranges;
+
+		apbh@80000000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x80000000 0x3c900>;
+			ranges;
+
+			icoll: interrupt-controller@80000000 {
+				compatible = "fsl,imx28-icoll", "fsl,mxs-icoll";
+				interrupt-controller;
+				#interrupt-cells = <1>;
+				reg = <0x80000000 0x2000>;
+			};
+
+			hsadc@80002000 {
+				reg = <0x80002000 2000>;
+				interrupts = <13 87>;
+				status = "disabled";
+			};
+
+			dma-apbh@80004000 {
+				compatible = "fsl,imx28-dma-apbh";
+				reg = <0x80004000 2000>;
+			};
+
+			perfmon@80006000 {
+				reg = <0x80006000 800>;
+				interrupts = <27>;
+				status = "disabled";
+			};
+
+			bch@8000a000 {
+				reg = <0x8000a000 2000>;
+				interrupts = <41>;
+				status = "disabled";
+			};
+
+			gpmi@8000c000 {
+				reg = <0x8000c000 2000>;
+				interrupts = <42 88>;
+				status = "disabled";
+			};
+
+			ssp0: ssp@80010000 {
+				reg = <0x80010000 2000>;
+				interrupts = <96 82>;
+				fsl,ssp-dma-channel = <0>;
+				status = "disabled";
+			};
+
+			ssp1: ssp@80012000 {
+				reg = <0x80012000 2000>;
+				interrupts = <97 83>;
+				fsl,ssp-dma-channel = <1>;
+				status = "disabled";
+			};
+
+			ssp2: ssp@80014000 {
+				reg = <0x80014000 2000>;
+				interrupts = <98 84>;
+				fsl,ssp-dma-channel = <2>;
+				status = "disabled";
+			};
+
+			ssp3: ssp@80016000 {
+				reg = <0x80016000 2000>;
+				interrupts = <99 85>;
+				fsl,ssp-dma-channel = <3>;
+				status = "disabled";
+			};
+
+			pinctrl@80018000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx28-pinctrl", "simple-bus";
+				reg = <0x80018000 2000>;
+
+				gpio0: gpio@0 {
+					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					interrupts = <127>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio1: gpio@1 {
+					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					interrupts = <126>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio2: gpio@2 {
+					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					interrupts = <125>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio3: gpio@3 {
+					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					interrupts = <124>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				gpio4: gpio@4 {
+					compatible = "fsl,imx28-gpio", "fsl,mxs-gpio";
+					interrupts = <123>;
+					gpio-controller;
+					#gpio-cells = <2>;
+					interrupt-controller;
+					#interrupt-cells = <2>;
+				};
+
+				duart_pins_a: duart@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x3102 0x3112>;
+					fsl,drive-strength = <0>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <0>;
+				};
+
+				mac0_pins_a: mac0@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x4000 0x4010 0x4020
+						0x4030 0x4040 0x4060 0x4070
+						0x4080 0x4100>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				mac1_pins_a: mac1@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x40f1 0x4091 0x40a1
+						0x40e1 0x40b1 0x40c1>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				mmc0_8bit_pins_a: mmc0-8bit@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x2000 0x2010 0x2020
+						0x2030 0x2040 0x2050 0x2060
+						0x2070 0x2080 0x2090 0x20a0>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				mmc0_cd_cfg: mmc0-cd-cfg {
+					fsl,pinmux-ids = <0x2090>;
+					fsl,pull-up = <0>;
+				};
+
+				mmc0_sck_cfg: mmc0-sck-cfg {
+					fsl,pinmux-ids = <0x20a0>;
+					fsl,drive-strength = <2>;
+					fsl,pull-up = <0>;
+				};
+
+				i2c0_pins_a: i2c0@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x3180 0x3190>;
+					fsl,drive-strength = <1>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				saif0_pins_a: saif0@0 {
+					reg = <0>;
+					fsl,pinmux-ids =
+						<0x3140 0x3150 0x3160 0x3170>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+
+				saif1_pins_a: saif1@0 {
+					reg = <0>;
+					fsl,pinmux-ids = <0x31a0>;
+					fsl,drive-strength = <2>;
+					fsl,voltage = <1>;
+					fsl,pull-up = <1>;
+				};
+			};
+
+			digctl@8001c000 {
+				reg = <0x8001c000 2000>;
+				interrupts = <89>;
+				status = "disabled";
+			};
+
+			etm@80022000 {
+				reg = <0x80022000 2000>;
+				status = "disabled";
+			};
+
+			dma-apbx@80024000 {
+				compatible = "fsl,imx28-dma-apbx";
+				reg = <0x80024000 2000>;
+			};
+
+			dcp@80028000 {
+				reg = <0x80028000 2000>;
+				interrupts = <52 53 54>;
+				status = "disabled";
+			};
+
+			pxp@8002a000 {
+				reg = <0x8002a000 2000>;
+				interrupts = <39>;
+				status = "disabled";
+			};
+
+			ocotp@8002c000 {
+				reg = <0x8002c000 2000>;
+				status = "disabled";
+			};
+
+			axi-ahb@8002e000 {
+				reg = <0x8002e000 2000>;
+				status = "disabled";
+			};
+
+			lcdif@80030000 {
+				reg = <0x80030000 2000>;
+				interrupts = <38 86>;
+				status = "disabled";
+			};
+
+			can0: can@80032000 {
+				reg = <0x80032000 2000>;
+				interrupts = <8>;
+				status = "disabled";
+			};
+
+			can1: can@80034000 {
+				reg = <0x80034000 2000>;
+				interrupts = <9>;
+				status = "disabled";
+			};
+
+			simdbg@8003c000 {
+				reg = <0x8003c000 200>;
+				status = "disabled";
+			};
+
+			simgpmisel@8003c200 {
+				reg = <0x8003c200 100>;
+				status = "disabled";
+			};
+
+			simsspsel@8003c300 {
+				reg = <0x8003c300 100>;
+				status = "disabled";
+			};
+
+			simmemsel@8003c400 {
+				reg = <0x8003c400 100>;
+				status = "disabled";
+			};
+
+			gpiomon@8003c500 {
+				reg = <0x8003c500 100>;
+				status = "disabled";
+			};
+
+			simenet@8003c700 {
+				reg = <0x8003c700 100>;
+				status = "disabled";
+			};
+
+			armjtag@8003c800 {
+				reg = <0x8003c800 100>;
+				status = "disabled";
+			};
+                };
+
+		apbx@80040000 {
+			compatible = "simple-bus";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x80040000 0x40000>;
+			ranges;
+
+			clkctl@80040000 {
+				reg = <0x80040000 2000>;
+				status = "disabled";
+			};
+
+			saif0: saif@80042000 {
+				compatible = "fsl,imx28-saif";
+				reg = <0x80042000 2000>;
+				interrupts = <59 80>;
+				fsl,saif-dma-channel = <4>;
+				status = "disabled";
+			};
+
+			power@80044000 {
+				reg = <0x80044000 2000>;
+				status = "disabled";
+			};
+
+			saif1: saif@80046000 {
+				compatible = "fsl,imx28-saif";
+				reg = <0x80046000 2000>;
+				interrupts = <58 81>;
+				fsl,saif-dma-channel = <5>;
+				status = "disabled";
+			};
+
+			lradc@80050000 {
+				reg = <0x80050000 2000>;
+				status = "disabled";
+			};
+
+			spdif@80054000 {
+				reg = <0x80054000 2000>;
+				interrupts = <45 66>;
+				status = "disabled";
+			};
+
+			rtc@80056000 {
+				reg = <0x80056000 2000>;
+				interrupts = <28 29>;
+				status = "disabled";
+			};
+
+			i2c0: i2c@80058000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx28-i2c";
+				reg = <0x80058000 2000>;
+				interrupts = <111 68>;
+				status = "disabled";
+			};
+
+			i2c1: i2c@8005a000 {
+				#address-cells = <1>;
+				#size-cells = <0>;
+				compatible = "fsl,imx28-i2c";
+				reg = <0x8005a000 2000>;
+				interrupts = <110 69>;
+				status = "disabled";
+			};
+
+			pwm@80064000 {
+				reg = <0x80064000 2000>;
+				status = "disabled";
+			};
+
+			timrot@80068000 {
+				reg = <0x80068000 2000>;
+				status = "disabled";
+			};
+
+			auart0: serial@8006a000 {
+				reg = <0x8006a000 0x2000>;
+				interrupts = <112 70 71>;
+				status = "disabled";
+			};
+
+			auart1: serial@8006c000 {
+				reg = <0x8006c000 0x2000>;
+				interrupts = <113 72 73>;
+				status = "disabled";
+			};
+
+			auart2: serial@8006e000 {
+				reg = <0x8006e000 0x2000>;
+				interrupts = <114 74 75>;
+				status = "disabled";
+			};
+
+			auart3: serial@80070000 {
+				reg = <0x80070000 0x2000>;
+				interrupts = <115 76 77>;
+				status = "disabled";
+			};
+
+			auart4: serial@80072000 {
+				reg = <0x80072000 0x2000>;
+				interrupts = <116 78 79>;
+				status = "disabled";
+			};
+
+			duart: serial@80074000 {
+				compatible = "arm,pl011", "arm,primecell";
+				reg = <0x80074000 0x1000>;
+				interrupts = <47>;
+				status = "disabled";
+			};
+
+			usbphy0: usbphy@8007c000 {
+				reg = <0x8007c000 0x2000>;
+				status = "disabled";
+			};
+
+			usbphy1: usbphy@8007e000 {
+				reg = <0x8007e000 0x2000>;
+				status = "disabled";
+			};
+		};
+	};
+
+	ahb@80080000 {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		reg = <0x80080000 0x80000>;
+		ranges;
+
+		usbctrl0: usbctrl@80080000 {
+			reg = <0x80080000 0x10000>;
+			status = "disabled";
+		};
+
+		usbctrl1: usbctrl@80090000 {
+			reg = <0x80090000 0x10000>;
+			status = "disabled";
+		};
+
+		dflpt@800c0000 {
+			reg = <0x800c0000 0x10000>;
+			status = "disabled";
+		};
+
+		mac0: ethernet@800f0000 {
+			compatible = "fsl,imx28-fec";
+			reg = <0x800f0000 0x4000>;
+			interrupts = <101>;
+			status = "disabled";
+		};
+
+		mac1: ethernet@800f4000 {
+			compatible = "fsl,imx28-fec";
+			reg = <0x800f4000 0x4000>;
+			interrupts = <102>;
+			status = "disabled";
+		};
+
+		switch@800f8000 {
+			reg = <0x800f8000 0x8000>;
+			status = "disabled";
+		};
+
+	};
+};

arch/arm/boot/dts/imx51-babbage.dts

@@ -17,10 +17,6 @@ / {
 	model = "Freescale i.MX51 Babbage Board";
 	compatible = "fsl,imx51-babbage", "fsl,imx51";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
-	};
-
 	memory {
 		reg = <0x90000000 0x20000000>;
 	};
@@ -40,7 +36,7 @@ esdhc@70008000 { /* ESDHC2 */
 					status = "okay";
 				};
 
-				uart3: uart@7000c000 {
+				uart3: serial@7000c000 {
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
@@ -166,6 +162,11 @@ partition@40000 {
 						};
 					};
 				};
+
+				ssi2: ssi@70014000 {
+					fsl,mode = "i2s-slave";
+					status = "okay";
+				};
 			};
 
 			wdog@73f98000 { /* WDOG1 */
@@ -177,12 +178,12 @@ iomuxc@73fa8000 {
 				reg = <0x73fa8000 0x4000>;
 			};
 
-			uart1: uart@73fbc000 {
+			uart1: serial@73fbc000 {
 				fsl,uart-has-rtscts;
 				status = "okay";
 			};
 
-			uart2: uart@73fc0000 {
+			uart2: serial@73fc0000 {
 				status = "okay";
 			};
 		};
@@ -195,13 +196,20 @@ sdma@83fb0000 {
 			i2c@83fc4000 { /* I2C2 */
 				status = "okay";
 
-				codec: sgtl5000@0a {
+				sgtl5000: codec@0a {
 					compatible = "fsl,sgtl5000";
 					reg = <0x0a>;
+					clock-frequency = <26000000>;
+					VDDA-supply = <&vdig_reg>;
+					VDDIO-supply = <&vvideo_reg>;
 				};
 			};
 
-			fec@83fec000 {
+			audmux@83fd0000 {
+				status = "okay";
+			};
+
+			ethernet@83fec000 {
 				phy-mode = "mii";
 				status = "okay";
 			};
@@ -218,4 +226,18 @@ power {
 			gpio-key,wakeup;
 		};
 	};
+
+	sound {
+		compatible = "fsl,imx51-babbage-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx51-babbage-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <3>;
+	};
 };

arch/arm/boot/dts/imx51.dtsi

@@ -86,7 +86,7 @@ esdhc@70008000 { /* ESDHC2 */
 					status = "disabled";
 				};
 
-				uart3: uart@7000c000 {
+				uart3: serial@7000c000 {
 					compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 					reg = <0x7000c000 0x4000>;
 					interrupts = <33>;
@@ -102,6 +102,15 @@ ecspi@70010000 { /* ECSPI1 */
 					status = "disabled";
 				};
 
+				ssi2: ssi@70014000 {
+					compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+					reg = <0x70014000 0x4000>;
+					interrupts = <30>;
+					fsl,fifo-depth = <15>;
+					fsl,ssi-dma-events = <25 24 23 22>; /* TX0 RX0 TX1 RX1 */
+					status = "disabled";
+				};
+
 				esdhc@70020000 { /* ESDHC3 */
 					compatible = "fsl,imx51-esdhc";
 					reg = <0x70020000 0x4000>;
@@ -171,14 +180,14 @@ wdog@73f9c000 { /* WDOG2 */
 				status = "disabled";
 			};
 
-			uart1: uart@73fbc000 {
+			uart1: serial@73fbc000 {
 				compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 				reg = <0x73fbc000 0x4000>;
 				interrupts = <31>;
 				status = "disabled";
 			};
 
-			uart2: uart@73fc0000 {
+			uart2: serial@73fc0000 {
 				compatible = "fsl,imx51-uart", "fsl,imx21-uart";
 				reg = <0x73fc0000 0x4000>;
 				interrupts = <32>;
@@ -235,7 +244,31 @@ i2c@83fc8000 { /* I2C1 */
 				status = "disabled";
 			};
 
-			fec@83fec000 {
+			ssi1: ssi@83fcc000 {
+				compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+				reg = <0x83fcc000 0x4000>;
+				interrupts = <29>;
+				fsl,fifo-depth = <15>;
+				fsl,ssi-dma-events = <29 28 27 26>; /* TX0 RX0 TX1 RX1 */
+				status = "disabled";
+			};
+
+			audmux@83fd0000 {
+				compatible = "fsl,imx51-audmux", "fsl,imx31-audmux";
+				reg = <0x83fd0000 0x4000>;
+				status = "disabled";
+			};
+
+			ssi3: ssi@83fe8000 {
+				compatible = "fsl,imx51-ssi", "fsl,imx21-ssi";
+				reg = <0x83fe8000 0x4000>;
+				interrupts = <96>;
+				fsl,fifo-depth = <15>;
+				fsl,ssi-dma-events = <47 46 37 35>; /* TX0 RX0 TX1 RX1 */
+				status = "disabled";
+			};
+
+			ethernet@83fec000 {
 				compatible = "fsl,imx51-fec", "fsl,imx27-fec";
 				reg = <0x83fec000 0x4000>;
 				interrupts = <87>;

arch/arm/boot/dts/imx53-ard.dts

@@ -17,10 +17,6 @@ / {
 	model = "Freescale i.MX53 Automotive Reference Design Board";
 	compatible = "fsl,imx53-ard", "fsl,imx53";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
-	};
-
 	memory {
 		reg = <0x70000000 0x40000000>;
 	};
@@ -44,7 +40,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart1: uart@53fbc000 {
+			uart1: serial@53fbc000 {
 				status = "okay";
 			};
 		};

arch/arm/boot/dts/imx53-evk.dts

@@ -17,10 +17,6 @@ / {
 	model = "Freescale i.MX53 Evaluation Kit";
 	compatible = "fsl,imx53-evk", "fsl,imx53";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
-	};
-
 	memory {
 		reg = <0x70000000 0x80000000>;
 	};
@@ -75,7 +71,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart1: uart@53fbc000 {
+			uart1: serial@53fbc000 {
 				status = "okay";
 			};
 		};
@@ -99,7 +95,7 @@ codec: sgtl5000@0a {
 				};
 			};
 
-			fec@63fec000 {
+			ethernet@63fec000 {
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";

arch/arm/boot/dts/imx53-qsb.dts

@@ -17,10 +17,6 @@ / {
 	model = "Freescale i.MX53 Quick Start Board";
 	compatible = "fsl,imx53-qsb", "fsl,imx53";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
-	};
-
 	memory {
 		reg = <0x70000000 0x40000000>;
 	};
@@ -33,6 +29,11 @@ esdhc@50004000 { /* ESDHC1 */
 					status = "okay";
 				};
 
+				ssi2: ssi@50014000 {
+					fsl,mode = "i2s-slave";
+					status = "okay";
+				};
+
 				esdhc@50020000 { /* ESDHC3 */
 					cd-gpios = <&gpio3 11 0>;
 					wp-gpios = <&gpio3 12 0>;
@@ -49,7 +50,7 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart1: uart@53fbc000 {
+			uart1: serial@53fbc000 {
 				status = "okay";
 			};
 		};
@@ -62,9 +63,11 @@ sdma@63fb0000 {
 			i2c@63fc4000 { /* I2C2 */
 				status = "okay";
 
-				codec: sgtl5000@0a {
+				sgtl5000: codec@0a {
 					compatible = "fsl,sgtl5000";
 					reg = <0x0a>;
+					VDDA-supply = <&reg_3p2v>;
+					VDDIO-supply = <&reg_3p2v>;
 				};
 			};
 
@@ -77,12 +80,88 @@ accelerometer: mma8450@1c {
 				};
 
 				pmic: dialog@48 {
-					compatible = "dialog,da9053", "dialog,da9052";
+					compatible = "dlg,da9053-aa", "dlg,da9052";
 					reg = <0x48>;
+
+					regulators {
+						buck0 {
+							regulator-min-microvolt = <500000>;
+							regulator-max-microvolt = <2075000>;
+						};
+
+						buck1 {
+							regulator-min-microvolt = <500000>;
+							regulator-max-microvolt = <2075000>;
+						};
+
+						buck2 {
+							regulator-min-microvolt = <925000>;
+					                regulator-max-microvolt = <2500000>;
+						};
+
+						buck3 {
+							regulator-min-microvolt = <925000>;
+					                regulator-max-microvolt = <2500000>;
+						};
+
+						ldo4 {
+							regulator-min-microvolt = <600000>;
+							regulator-max-microvolt = <1800000>;
 						};
+
+						ldo5 {
+							regulator-min-microvolt = <600000>;
+					                regulator-max-microvolt = <1800000>;
+						};
+
+						ldo6 {
+							regulator-min-microvolt = <1725000>;
+					                regulator-max-microvolt = <3300000>;
 						};
 
-			fec@63fec000 {
+						ldo7 {
+							regulator-min-microvolt = <1725000>;
+					                regulator-max-microvolt = <3300000>;
+						};
+
+						ldo8 {
+							regulator-min-microvolt = <1200000>;
+					                regulator-max-microvolt = <3600000>;
+						};
+
+						ldo9 {
+							regulator-min-microvolt = <1200000>;
+					                regulator-max-microvolt = <3600000>;
+						};
+
+						ldo10 {
+							regulator-min-microvolt = <1200000>;
+					                regulator-max-microvolt = <3600000>;
+						};
+
+						ldo11 {
+							regulator-min-microvolt = <1200000>;
+					                regulator-max-microvolt = <3600000>;
+						};
+
+						ldo12 {
+							regulator-min-microvolt = <1250000>;
+					                regulator-max-microvolt = <3650000>;
+						};
+
+						ldo13 {
+							regulator-min-microvolt = <1200000>;
+					                regulator-max-microvolt = <3600000>;
+						};
+					};
+				};
+			};
+
+			audmux@63fd0000 {
+				status = "okay";
+			};
+
+			ethernet@63fec000 {
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";
@@ -122,4 +201,30 @@ user {
 			linux,default-trigger = "heartbeat";
 		};
 	};
+
+	regulators {
+		compatible = "simple-bus";
+
+		reg_3p2v: 3p2v {
+			compatible = "regulator-fixed";
+			regulator-name = "3P2V";
+			regulator-min-microvolt = <3200000>;
+			regulator-max-microvolt = <3200000>;
+			regulator-always-on;
+		};
+	};
+
+	sound {
+		compatible = "fsl,imx53-qsb-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx53-qsb-sgtl5000";
+		ssi-controller = <&ssi2>;
+		audio-codec = <&sgtl5000>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <2>;
+		mux-ext-port = <5>;
+	};
 };

arch/arm/boot/dts/imx53-smd.dts

@@ -17,10 +17,6 @@ / {
 	model = "Freescale i.MX53 Smart Mobile Reference Design Board";
 	compatible = "fsl,imx53-smd", "fsl,imx53";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk0p3 rootwait";
-	};
-
 	memory {
 		reg = <0x70000000 0x40000000>;
 	};
@@ -39,7 +35,7 @@ esdhc@50008000 { /* ESDHC2 */
 					status = "okay";
 				};
 
-				uart3: uart@5000c000 {
+				uart3: serial@5000c000 {
 					fsl,uart-has-rtscts;
 					status = "okay";
 				};
@@ -90,11 +86,11 @@ iomuxc@53fa8000 {
 				reg = <0x53fa8000 0x4000>;
 			};
 
-			uart1: uart@53fbc000 {
+			uart1: serial@53fbc000 {
 				status = "okay";
 			};
 
-			uart2: uart@53fc0000 {
+			uart2: serial@53fc0000 {
 				status = "okay";
 			};
 		};
@@ -142,7 +138,7 @@ pmic: dialog@48 {
 				};
 			};
 
-			fec@63fec000 {
+			ethernet@63fec000 {
 				phy-mode = "rmii";
 				phy-reset-gpios = <&gpio7 6 0>;
 				status = "okay";

arch/arm/boot/dts/imx53.dtsi

@@ -88,7 +88,7 @@ esdhc@50008000 { /* ESDHC2 */
 					status = "disabled";
 				};
 
-				uart3: uart@5000c000 {
+				uart3: serial@5000c000 {
 					compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 					reg = <0x5000c000 0x4000>;
 					interrupts = <33>;
@@ -104,6 +104,15 @@ ecspi@50010000 { /* ECSPI1 */
 					status = "disabled";
 				};
 
+				ssi2: ssi@50014000 {
+					compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+					reg = <0x50014000 0x4000>;
+					interrupts = <30>;
+					fsl,fifo-depth = <15>;
+					fsl,ssi-dma-events = <25 24 23 22>; /* TX0 RX0 TX1 RX1 */
+					status = "disabled";
+				};
+
 				esdhc@50020000 { /* ESDHC3 */
 					compatible = "fsl,imx53-esdhc";
 					reg = <0x50020000 0x4000>;
@@ -173,14 +182,14 @@ wdog@53f9c000 { /* WDOG2 */
 				status = "disabled";
 			};
 
-			uart1: uart@53fbc000 {
+			uart1: serial@53fbc000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53fbc000 0x4000>;
 				interrupts = <31>;
 				status = "disabled";
 			};
 
-			uart2: uart@53fc0000 {
+			uart2: serial@53fc0000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53fc0000 0x4000>;
 				interrupts = <32>;
@@ -226,7 +235,7 @@ i2c@53fec000 { /* I2C3 */
 				status = "disabled";
 			};
 
-			uart4: uart@53ff0000 {
+			uart4: serial@53ff0000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x53ff0000 0x4000>;
 				interrupts = <13>;
@@ -241,7 +250,7 @@ aips@60000000 {	/* AIPS2 */
 			reg = <0x60000000 0x10000000>;
 			ranges;
 
-			uart5: uart@63f90000 {
+			uart5: serial@63f90000 {
 				compatible = "fsl,imx53-uart", "fsl,imx21-uart";
 				reg = <0x63f90000 0x4000>;
 				interrupts = <86>;
@@ -290,7 +299,31 @@ i2c@63fc8000 { /* I2C1 */
 				status = "disabled";
 			};
 
-			fec@63fec000 {
+			ssi1: ssi@63fcc000 {
+				compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+				reg = <0x63fcc000 0x4000>;
+				interrupts = <29>;
+				fsl,fifo-depth = <15>;
+				fsl,ssi-dma-events = <29 28 27 26>; /* TX0 RX0 TX1 RX1 */
+				status = "disabled";
+			};
+
+			audmux@63fd0000 {
+				compatible = "fsl,imx53-audmux", "fsl,imx31-audmux";
+				reg = <0x63fd0000 0x4000>;
+				status = "disabled";
+			};
+
+			ssi3: ssi@63fe8000 {
+				compatible = "fsl,imx53-ssi", "fsl,imx21-ssi";
+				reg = <0x63fe8000 0x4000>;
+				interrupts = <96>;
+				fsl,fifo-depth = <15>;
+				fsl,ssi-dma-events = <47 46 45 44>; /* TX0 RX0 TX1 RX1 */
+				status = "disabled";
+			};
+
+			ethernet@63fec000 {
 				compatible = "fsl,imx53-fec", "fsl,imx25-fec";
 				reg = <0x63fec000 0x4000>;
 				interrupts = <87>;

arch/arm/boot/dts/imx6q-arm2.dts

@@ -17,19 +17,14 @@ / {
 	model = "Freescale i.MX6 Quad Armadillo2 Board";
 	compatible = "fsl,imx6q-arm2", "fsl,imx6q";
 
-	chosen {
-		bootargs = "console=ttymxc0,115200 root=/dev/mmcblk3p3 rootwait";
-	};
-
 	memory {
 		reg = <0x10000000 0x80000000>;
 	};
 
 	soc {
 		aips-bus@02100000 { /* AIPS2 */
-			enet@02188000 {
+			ethernet@02188000 {
 				phy-mode = "rgmii";
-				local-mac-address = [00 04 9F 01 1B 61];
 				status = "okay";
 			};
 
@@ -37,16 +32,20 @@ usdhc@02198000 { /* uSDHC3 */
 				cd-gpios = <&gpio6 11 0>;
 				wp-gpios = <&gpio6 14 0>;
 				vmmc-supply = <&reg_3p3v>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc3_1>;
 				status = "okay";
 			};
 
 			usdhc@0219c000 { /* uSDHC4 */
 				non-removable;
 				vmmc-supply = <&reg_3p3v>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_usdhc4_1>;
 				status = "okay";
 			};
 
-			uart4: uart@021f0000 {
+			uart4: serial@021f0000 {
 				status = "okay";
 			};
 		};

arch/arm/boot/dts/imx6q-sabrelite.dts

@@ -22,8 +22,30 @@ memory {
 	};
 
 	soc {
+		aips-bus@02000000 { /* AIPS1 */
+			spba-bus@02000000 {
+				ecspi@02008000 { /* eCSPI1 */
+					fsl,spi-num-chipselects = <1>;
+					cs-gpios = <&gpio3 19 0>;
+					status = "okay";
+
+					flash: m25p80@0 {
+						compatible = "sst,sst25vf016b";
+						spi-max-frequency = <20000000>;
+						reg = <0>;
+					};
+				};
+
+				ssi1: ssi@02028000 {
+					fsl,mode = "i2s-slave";
+					status = "okay";
+				};
+			};
+
+		};
+
 		aips-bus@02100000 { /* AIPS2 */
-			enet@02188000 {
+			ethernet@02188000 {
 				phy-mode = "rgmii";
 				phy-reset-gpios = <&gpio3 23 0>;
 				status = "okay";
@@ -43,13 +65,23 @@ usdhc@0219c000 { /* uSDHC4 */
 				status = "okay";
 			};
 
-			uart2: uart@021e8000 {
+			audmux@021d8000 {
+				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_audmux_1>;
+			};
+
+			uart2: serial@021e8000 {
 				status = "okay";
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_serial2_1>;
 			};
 
 			i2c@021a0000 { /* I2C1 */
 				status = "okay";
 				clock-frequency = <100000>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&pinctrl_i2c1_1>;
 
 				codec: sgtl5000@0a {
 					compatible = "fsl,sgtl5000";
@@ -80,4 +112,18 @@ reg_3p3v: 3p3v {
 			regulator-always-on;
 		};
 	};
+
+	sound {
+		compatible = "fsl,imx6q-sabrelite-sgtl5000",
+			     "fsl,imx-audio-sgtl5000";
+		model = "imx6q-sabrelite-sgtl5000";
+		ssi-controller = <&ssi1>;
+		audio-codec = <&codec>;
+		audio-routing =
+			"MIC_IN", "Mic Jack",
+			"Mic Jack", "Mic Bias",
+			"Headphone Jack", "HP_OUT";
+		mux-int-port = <1>;
+		mux-ext-port = <4>;
+	};
 };

arch/arm/boot/dts/imx6q-sabresd.dts

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx6q.dtsi"
+
+/ {
+	model = "Freescale i.MX6Q SABRE Smart Device Board";
+	compatible = "fsl,imx6q-sabresd", "fsl,imx6q";
+
+	memory {
+		reg = <0x10000000 0x40000000>;
+	};
+
+	soc {
+
+		aips-bus@02000000 { /* AIPS1 */
+			spba-bus@02000000 {
+				uart1: serial@02020000 {
+					status = "okay";
+				};
+			};
+		};
+
+		aips-bus@02100000 { /* AIPS2 */
+			ethernet@02188000 {
+				phy-mode = "rgmii";
+				status = "okay";
+			};
+
+			usdhc@02194000 { /* uSDHC2 */
+				cd-gpios = <&gpio2 2 0>;
+				wp-gpios = <&gpio2 3 0>;
+				status = "okay";
+			};
+
+			usdhc@02198000 { /* uSDHC3 */
+				cd-gpios = <&gpio2 0 0>;
+				wp-gpios = <&gpio2 1 0>;
+				status = "okay";
+			};
+		};
+	};
+};

arch/arm/boot/dts/imx6q.dtsi

@@ -165,7 +165,7 @@ ecspi@02018000 { /* eCSPI5 */
 					status = "disabled";
 				};
 
-				uart1: uart@02020000 {
+				uart1: serial@02020000 {
 					compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 					reg = <0x02020000 0x4000>;
 					interrupts = <0 26 0x04>;
@@ -177,19 +177,31 @@ esai@02024000 {
 					interrupts = <0 51 0x04>;
 				};
 
-				ssi@02028000 { /* SSI1 */
+				ssi1: ssi@02028000 {
+					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x02028000 0x4000>;
 					interrupts = <0 46 0x04>;
+					fsl,fifo-depth = <15>;
+					fsl,ssi-dma-events = <38 37>;
+					status = "disabled";
 				};
 
-				ssi@0202c000 { /* SSI2 */
+				ssi2: ssi@0202c000 {
+					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x0202c000 0x4000>;
 					interrupts = <0 47 0x04>;
+					fsl,fifo-depth = <15>;
+					fsl,ssi-dma-events = <42 41>;
+					status = "disabled";
 				};
 
-				ssi@02030000 { /* SSI3 */
+				ssi3: ssi@02030000 {
+					compatible = "fsl,imx6q-ssi","fsl,imx21-ssi";
 					reg = <0x02030000 0x4000>;
 					interrupts = <0 48 0x04>;
+					fsl,fifo-depth = <15>;
+					fsl,ssi-dma-events = <46 45>;
+					status = "disabled";
 				};
 
 				asrc@02034000 {
@@ -346,6 +358,90 @@ anatop@020c8000 {
 				compatible = "fsl,imx6q-anatop";
 				reg = <0x020c8000 0x1000>;
 				interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
+
+				regulator-1p1@110 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd1p1";
+					regulator-min-microvolt = <800000>;
+					regulator-max-microvolt = <1375000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x110>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <4>;
+					anatop-min-voltage = <800000>;
+					anatop-max-voltage = <1375000>;
+				};
+
+				regulator-3p0@120 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd3p0";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <3150000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x120>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <0>;
+					anatop-min-voltage = <2625000>;
+					anatop-max-voltage = <3400000>;
+				};
+
+				regulator-2p5@130 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vdd2p5";
+					regulator-min-microvolt = <2000000>;
+					regulator-max-microvolt = <2750000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x130>;
+					anatop-vol-bit-shift = <8>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <0>;
+					anatop-min-voltage = <2000000>;
+					anatop-max-voltage = <2750000>;
+				};
+
+				regulator-vddcore@140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "cpu";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <0>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+
+				regulator-vddpu@140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vddpu";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <9>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
+
+				regulator-vddsoc@140 {
+					compatible = "fsl,anatop-regulator";
+					regulator-name = "vddsoc";
+					regulator-min-microvolt = <725000>;
+					regulator-max-microvolt = <1450000>;
+					regulator-always-on;
+					anatop-reg-offset = <0x140>;
+					anatop-vol-bit-shift = <18>;
+					anatop-vol-bit-width = <5>;
+					anatop-min-bit-val = <1>;
+					anatop-min-voltage = <725000>;
+					anatop-max-voltage = <1450000>;
+				};
 			};
 
 			usbphy@020c9000 { /* USBPHY1 */
@@ -386,7 +482,62 @@ gpc@020dc000 {
 			};
 
 			iomuxc@020e0000 {
+				compatible = "fsl,imx6q-iomuxc";
 				reg = <0x020e0000 0x4000>;
+
+				/* shared pinctrl settings */
+				audmux {
+					pinctrl_audmux_1: audmux-1 {
+						fsl,pins = <18   0x80000000	/* MX6Q_PAD_SD2_DAT0__AUDMUX_AUD4_RXD */
+							    1586 0x80000000	/* MX6Q_PAD_SD2_DAT3__AUDMUX_AUD4_TXC */
+							    11   0x80000000	/* MX6Q_PAD_SD2_DAT2__AUDMUX_AUD4_TXD */
+							    3    0x80000000>;	/* MX6Q_PAD_SD2_DAT1__AUDMUX_AUD4_TXFS */
+					};
+				};
+
+				i2c1 {
+					pinctrl_i2c1_1: i2c1grp-1 {
+						fsl,pins = <137 0x4001b8b1	/* MX6Q_PAD_EIM_D21__I2C1_SCL */
+							    196 0x4001b8b1>;	/* MX6Q_PAD_EIM_D28__I2C1_SDA */
+					};
+				};
+
+				serial2 {
+					pinctrl_serial2_1: serial2grp-1 {
+						fsl,pins = <183 0x1b0b1		/* MX6Q_PAD_EIM_D26__UART2_TXD */
+							    191 0x1b0b1>;	/* MX6Q_PAD_EIM_D27__UART2_RXD */
+					};
+				};
+
+				usdhc3 {
+					pinctrl_usdhc3_1: usdhc3grp-1 {
+						fsl,pins = <1273 0x17059	/* MX6Q_PAD_SD3_CMD__USDHC3_CMD */
+							    1281 0x10059	/* MX6Q_PAD_SD3_CLK__USDHC3_CLK	*/
+							    1289 0x17059	/* MX6Q_PAD_SD3_DAT0__USDHC3_DAT0 */
+							    1297 0x17059	/* MX6Q_PAD_SD3_DAT1__USDHC3_DAT1 */
+							    1305 0x17059	/* MX6Q_PAD_SD3_DAT2__USDHC3_DAT2 */
+							    1312 0x17059	/* MX6Q_PAD_SD3_DAT3__USDHC3_DAT3 */
+							    1265 0x17059	/* MX6Q_PAD_SD3_DAT4__USDHC3_DAT4 */
+							    1257 0x17059	/* MX6Q_PAD_SD3_DAT5__USDHC3_DAT5 */
+							    1249 0x17059	/* MX6Q_PAD_SD3_DAT6__USDHC3_DAT6 */
+							    1241 0x17059>;	/* MX6Q_PAD_SD3_DAT7__USDHC3_DAT7 */
+					};
+				};
+
+				usdhc4 {
+					pinctrl_usdhc4_1: usdhc4grp-1 {
+						fsl,pins = <1386 0x17059	/* MX6Q_PAD_SD4_CMD__USDHC4_CMD */
+							    1392 0x10059	/* MX6Q_PAD_SD4_CLK__USDHC4_CLK	*/
+							    1462 0x17059	/* MX6Q_PAD_SD4_DAT0__USDHC4_DAT0 */
+							    1470 0x17059	/* MX6Q_PAD_SD4_DAT1__USDHC4_DAT1 */
+							    1478 0x17059	/* MX6Q_PAD_SD4_DAT2__USDHC4_DAT2 */
+							    1486 0x17059	/* MX6Q_PAD_SD4_DAT3__USDHC4_DAT3 */
+							    1493 0x17059	/* MX6Q_PAD_SD4_DAT4__USDHC4_DAT4 */
+							    1501 0x17059	/* MX6Q_PAD_SD4_DAT5__USDHC4_DAT5 */
+							    1509 0x17059	/* MX6Q_PAD_SD4_DAT6__USDHC4_DAT6 */
+							    1517 0x17059>;	/* MX6Q_PAD_SD4_DAT7__USDHC4_DAT7 */
+					};
+				};
 			};
 
 			dcic@020e4000 { /* DCIC1 */
@@ -422,7 +573,7 @@ aipstz@0217c000 { /* AIPSTZ2 */
 				reg = <0x0217c000 0x4000>;
 			};
 
-			enet@02188000 {
+			ethernet@02188000 {
 				compatible = "fsl,imx6q-fec";
 				reg = <0x02188000 0x4000>;
 				interrupts = <0 118 0x04 0 119 0x04>;
@@ -527,7 +678,9 @@ tzasc@021d4000 { /* TZASC2 */
 			};
 
 			audmux@021d8000 {
+				compatible = "fsl,imx6q-audmux", "fsl,imx31-audmux";
 				reg = <0x021d8000 0x4000>;
+				status = "disabled";
 			};
 
 			mipi@021dc000 { /* MIPI-CSI */
@@ -543,28 +696,28 @@ vdoa@021e4000 {
 				interrupts = <0 18 0x04>;
 			};
 
-			uart2: uart@021e8000 {
+			uart2: serial@021e8000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021e8000 0x4000>;
 				interrupts = <0 27 0x04>;
 				status = "disabled";
 			};
 
-			uart3: uart@021ec000 {
+			uart3: serial@021ec000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021ec000 0x4000>;
 				interrupts = <0 28 0x04>;
 				status = "disabled";
 			};
 
-			uart4: uart@021f0000 {
+			uart4: serial@021f0000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f0000 0x4000>;
 				interrupts = <0 29 0x04>;
 				status = "disabled";
 			};
 
-			uart5: uart@021f4000 {
+			uart5: serial@021f4000 {
 				compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
 				reg = <0x021f4000 0x4000>;
 				interrupts = <0 30 0x04>;

arch/arm/boot/dts/tegra-cardhu.dts

@@ -7,10 +7,10 @@ / {
 	compatible = "nvidia,cardhu", "nvidia,tegra30";
 
 	memory {
-		reg = < 0x80000000 0x40000000 >;
+		reg = <0x80000000 0x40000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -64,42 +64,40 @@ dap2_fs_pa2 {
 	};
 
 	serial@70006000 {
-		clock-frequency = < 408000000 >;
-	};
-
-	serial@70006040 {
-		status = "disable";
-	};
-
-	serial@70006200 {
-		status = "disable";
-	};
-
-	serial@70006300 {
-		status = "disable";
-	};
-
-	serial@70006400 {
-		status = "disable";
+		status = "okay";
+		clock-frequency = <408000000>;
 	};
 
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <100000>;
 	};
 
 	i2c@7000c400 {
+		status = "okay";
 		clock-frequency = <100000>;
 	};
 
 	i2c@7000c500 {
+		status = "okay";
 		clock-frequency = <100000>;
+
+		/* ALS and Proximity sensor */
+		isl29028@44 {
+			compatible = "isil,isl29028";
+			reg = <0x44>;
+			interrupt-parent = <&gpio>;
+			interrupts = <88 0x04>; /*gpio PL0 */
+		};
 	};
 
 	i2c@7000c700 {
+		status = "okay";
 		clock-frequency = <100000>;
 	};
 
 	i2c@7000d000 {
+		status = "okay";
 		clock-frequency = <100000>;
 
 		wm8903: wm8903@1a {
@@ -115,46 +113,41 @@ wm8903: wm8903@1a {
 			micdet-delay = <100>;
 			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
 		};
+
+		tps62361 {
+			compatible = "ti,tps62361";
+			reg = <0x60>;
+
+			regulator-name = "tps62361-vout";
+			regulator-min-microvolt = <500000>;
+			regulator-max-microvolt = <1500000>;
+			regulator-boot-on;
+			regulator-always-on;
+			ti,vsel0-state-high;
+			ti,vsel1-state-high;
+		};
+	};
+
+	ahub {
+		i2s@70080400 {
+			status = "okay";
+		};
 	};
 
 	sdhci@78000000 {
+		status = "okay";
 		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
 		wp-gpios = <&gpio 155 0>; /* gpio PT3 */
 		power-gpios = <&gpio 31 0>; /* gpio PD7 */
 		bus-width = <4>;
 	};
 
-	sdhci@78000200 {
-		status = "disable";
-	};
-
-	sdhci@78000400 {
-		status = "disable";
-	};
-
-	sdhci@78000400 {
+	sdhci@78000600 {
+		status = "okay";
 		support-8bit;
 		bus-width = <8>;
 	};
 
-	ahub@70080000 {
-		i2s@70080300 {
-			status = "disable";
-		};
-
-		i2s@70080500 {
-			status = "disable";
-		};
-
-		i2s@70080600 {
-			status = "disable";
-		};
-
-		i2s@70080700 {
-			status = "disable";
-		};
-	};
-
 	sound {
 		compatible = "nvidia,tegra-audio-wm8903-cardhu",
 			     "nvidia,tegra-audio-wm8903";

arch/arm/boot/dts/tegra-harmony.dts

@@ -6,11 +6,11 @@ / {
 	model = "NVIDIA Tegra2 Harmony evaluation board";
 	compatible = "nvidia,harmony", "nvidia,tegra20";
 
-	memory@0 {
-		reg = < 0x00000000 0x40000000 >;
+	memory {
+		reg = <0x00000000 0x40000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -234,42 +234,81 @@ conf_ld17_0 {
 		};
 	};
 
-	pmc@7000f400 {
-		nvidia,invert-interrupt;
+	i2s@70002800 {
+		status = "okay";
+	};
+
+	serial@70006300 {
+		status = "okay";
+		clock-frequency = <216000000>;
 	};
 
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
 			reg = <0x1a>;
 			interrupt-parent = <&gpio>;
-			interrupts = < 187 0x04 >;
+			interrupts = <187 0x04>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
 
 			micdet-cfg = <0>;
 			micdet-delay = <100>;
-			gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
 		};
 	};
 
 	i2c@7000c400 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000c500 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000d000 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
-	i2s@70002a00 {
-		status = "disable";
+	pmc {
+		nvidia,invert-interrupt;
+	};
+
+	usb@c5000000 {
+		status = "okay";
+	};
+
+	usb@c5004000 {
+		status = "okay";
+		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+	};
+
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	sdhci@c8000200 {
+		status = "okay";
+		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+		wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+		power-gpios = <&gpio 155 0>; /* gpio PT3 */
+		bus-width = <4>;
+	};
+
+	sdhci@c8000600 {
+		status = "okay";
+		cd-gpios = <&gpio 58 0>; /* gpio PH2 */
+		wp-gpios = <&gpio 59 0>; /* gpio PH3 */
+		power-gpios = <&gpio 70 0>; /* gpio PI6 */
+		support-8bit;
+		bus-width = <8>;
 	};
 
 	sound {
@@ -295,51 +334,4 @@ sound {
 		nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
 		nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
 	};
-
-	serial@70006000 {
-		status = "disable";
-	};
-
-	serial@70006040 {
-		status = "disable";
-	};
-
-	serial@70006200 {
-		status = "disable";
-	};
-
-	serial@70006300 {
-		clock-frequency = < 216000000 >;
-	};
-
-	serial@70006400 {
-		status = "disable";
-	};
-
-	sdhci@c8000000 {
-		status = "disable";
-	};
-
-	sdhci@c8000200 {
-		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
-		wp-gpios = <&gpio 57 0>; /* gpio PH1 */
-		power-gpios = <&gpio 155 0>; /* gpio PT3 */
-		bus-width = <4>;
-	};
-
-	sdhci@c8000400 {
-		status = "disable";
-	};
-
-	sdhci@c8000600 {
-		cd-gpios = <&gpio 58 0>; /* gpio PH2 */
-		wp-gpios = <&gpio 59 0>; /* gpio PH3 */
-		power-gpios = <&gpio 70 0>; /* gpio PI6 */
-		support-8bit;
-		bus-width = <8>;
-	};
-
-	usb@c5004000 {
-		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
-	};
 };

arch/arm/boot/dts/tegra-paz00.dts

@@ -6,11 +6,11 @@ / {
 	model = "Toshiba AC100 / Dynabook AZ";
 	compatible = "compal,paz00", "nvidia,tegra20";
 
-	memory@0 {
+	memory {
 		reg = <0x00000000 0x20000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -226,7 +226,22 @@ conf_ld17_0 {
 		};
 	};
 
+	i2s@70002800 {
+		status = "okay";
+	};
+
+	serial@70006000 {
+		status = "okay";
+		clock-frequency = <216000000>;
+	};
+
+	serial@70006200 {
+		status = "okay";
+		clock-frequency = <216000000>;
+	};
+
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
 		alc5632: alc5632@1e {
@@ -238,25 +253,23 @@ alc5632: alc5632@1e {
 	};
 
 	i2c@7000c400 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
-	i2c@7000c500 {
-		status = "disable";
-	};
-
-	nvec@7000c500 {
-		#address-cells = <1>;
-		#size-cells = <0>;
+	nvec {
 		compatible = "nvidia,nvec";
-		reg = <0x7000C500 0x100>;
+		reg = <0x7000c500 0x100>;
 		interrupts = <0 92 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 		clock-frequency = <80000>;
-		request-gpios = <&gpio 170 0>;
+		request-gpios = <&gpio 170 0>; /* gpio PV2 */
 		slave-addr = <138>;
 	};
 
 	i2c@7000d000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
 		adt7461@4c {
@@ -265,66 +278,29 @@ adt7461@4c {
 		};
 	};
 
-	i2s@70002a00 {
-		status = "disable";
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-alc5632-paz00",
-			"nvidia,tegra-audio-alc5632";
-
-		nvidia,model = "Compal PAZ00";
-
-		nvidia,audio-routing =
-			"Int Spk", "SPKOUT",
-			"Int Spk", "SPKOUTN",
-			"Headset Mic", "MICBIAS1",
-			"MIC1", "Headset Mic",
-			"Headset Stereophone", "HPR",
-			"Headset Stereophone", "HPL",
-			"DMICDAT", "Digital Mic";
-
-		nvidia,audio-codec = <&alc5632>;
-		nvidia,i2s-controller = <&tegra_i2s1>;
-		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
-	};
-
-	serial@70006000 {
-		clock-frequency = <216000000>;
-	};
-
-	serial@70006040 {
-		status = "disable";
-	};
-
-	serial@70006200 {
-		clock-frequency = <216000000>;
+	usb@c5000000 {
+		status = "okay";
 	};
 
-	serial@70006300 {
-		status = "disable";
+	usb@c5004000 {
+		status = "okay";
+		nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
 	};
 
-	serial@70006400 {
-		status = "disable";
+	usb@c5008000 {
+		status = "okay";
 	};
 
 	sdhci@c8000000 {
+		status = "okay";
 		cd-gpios = <&gpio 173 0>; /* gpio PV5 */
 		wp-gpios = <&gpio 57 0>;  /* gpio PH1 */
 		power-gpios = <&gpio 169 0>; /* gpio PV1 */
 		bus-width = <4>;
 	};
 
-	sdhci@c8000200 {
-		status = "disable";
-	};
-
-	sdhci@c8000400 {
-		status = "disable";
-	};
-
 	sdhci@c8000600 {
+		status = "okay";
 		support-8bit;
 		bus-width = <8>;
 	};
@@ -345,12 +321,28 @@ gpio-leds {
 
 		wifi {
 			label = "wifi-led";
-			gpios = <&gpio 24 0>;
+			gpios = <&gpio 24 0>; /* gpio PD0 */
 			linux,default-trigger = "rfkill0";
 		};
 	};
 
-	usb@c5004000 {
-		nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+	sound {
+		compatible = "nvidia,tegra-audio-alc5632-paz00",
+			"nvidia,tegra-audio-alc5632";
+
+		nvidia,model = "Compal PAZ00";
+
+		nvidia,audio-routing =
+			"Int Spk", "SPKOUT",
+			"Int Spk", "SPKOUTN",
+			"Headset Mic", "MICBIAS1",
+			"MIC1", "Headset Mic",
+			"Headset Stereophone", "HPR",
+			"Headset Stereophone", "HPL",
+			"DMICDAT", "Digital Mic";
+
+		nvidia,audio-codec = <&alc5632>;
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
 	};
 };

arch/arm/boot/dts/tegra-seaboard.dts

@@ -7,11 +7,10 @@ / {
 	compatible = "nvidia,seaboard", "nvidia,tegra20";
 
 	memory {
-		device_type = "memory";
-		reg = < 0x00000000 0x40000000 >;
+		reg = <0x00000000 0x40000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -100,7 +99,7 @@ gpv {
 			};
 			hdint {
 				nvidia,pins = "hdint", "lpw0", "lpw2", "lsc1",
-					"lsck", "lsda", "pta";
+					"lsck", "lsda";
 				nvidia,function = "hdmi";
 			};
 			i2cp {
@@ -134,6 +133,10 @@ pmc {
 				nvidia,pins = "pmc";
 				nvidia,function = "pwr_on";
 			};
+			pta {
+				nvidia,pins = "pta";
+				nvidia,function = "i2c2";
+			};
 			rm {
 				nvidia,pins = "rm";
 				nvidia,function = "i2c1";
@@ -254,96 +257,138 @@ drive_sdio1 {
 		};
 	};
 
+	i2s@70002800 {
+		status = "okay";
+	};
+
+	serial@70006300 {
+		status = "okay";
+		clock-frequency = <216000000>;
+	};
+
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
 			reg = <0x1a>;
 			interrupt-parent = <&gpio>;
-			interrupts = < 187 0x04 >;
+			interrupts = <187 0x04>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
 
 			micdet-cfg = <0>;
 			micdet-delay = <100>;
-			gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+		};
+
+		/* ALS and proximity sensor */
+		isl29018@44 {
+			compatible = "isil,isl29018";
+			reg = <0x44>;
+			interrupt-parent = <&gpio>;
+			interrupts = <202 0x04>; /* GPIO PZ2 */
+		};
+
+		gyrometer@68 {
+			compatible = "invn,mpu3050";
+			reg = <0x68>;
+			interrupt-parent = <&gpio>;
+			interrupts = <204 0x04>; /* gpio PZ4 */
 		};
 	};
 
 	i2c@7000c400 {
-		clock-frequency = <400000>;
+		status = "okay";
+		clock-frequency = <100000>;
+
+		smart-battery@b {
+			compatible = "ti,bq20z75", "smart-battery-1.1";
+			reg = <0xb>;
+			ti,i2c-retry-count = <2>;
+			ti,poll-retry-count = <10>;
+		};
 	};
 
 	i2c@7000c500 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000d000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
-		adt7461@4c {
-			compatible = "adt7461";
+		temperature-sensor@4c {
+			compatible = "nct1008";
 			reg = <0x4c>;
 		};
-	};
-
-	i2s@70002a00 {
-		status = "disable";
-	};
-
-	sound {
-		compatible = "nvidia,tegra-audio-wm8903-seaboard",
-			     "nvidia,tegra-audio-wm8903";
-		nvidia,model = "NVIDIA Tegra Seaboard";
-
-		nvidia,audio-routing =
-			"Headphone Jack", "HPOUTR",
-			"Headphone Jack", "HPOUTL",
-			"Int Spk", "ROP",
-			"Int Spk", "RON",
-			"Int Spk", "LOP",
-			"Int Spk", "LON",
-			"Mic Jack", "MICBIAS",
-			"IN1R", "Mic Jack";
-
-		nvidia,i2s-controller = <&tegra_i2s1>;
-		nvidia,audio-codec = <&wm8903>;
 
-		nvidia,spkr-en-gpios = <&wm8903 2 0>;
-		nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
+		magnetometer@c {
+			compatible = "ak8975";
+			reg = <0xc>;
+			interrupt-parent = <&gpio>;
+			interrupts = <109 0x04>; /* gpio PN5 */
 		};
-
-	serial@70006000 {
-		status = "disable";
 	};
 
-	serial@70006040 {
-		status = "disable";
+	emc {
+		emc-table@190000 {
+			reg = <190000>;
+			compatible = "nvidia,tegra20-emc-table";
+			clock-frequency = <190000>;
+			nvidia,emc-registers = <0x0000000c 0x00000026
+				0x00000009 0x00000003 0x00000004 0x00000004
+				0x00000002 0x0000000c 0x00000003 0x00000003
+				0x00000002 0x00000001 0x00000004 0x00000005
+				0x00000004 0x00000009 0x0000000d 0x0000059f
+				0x00000000 0x00000003 0x00000003 0x00000003
+				0x00000003 0x00000001 0x0000000b 0x000000c8
+				0x00000003 0x00000007 0x00000004 0x0000000f
+				0x00000002 0x00000000 0x00000000 0x00000002
+				0x00000000 0x00000000 0x00000083 0xa06204ae
+				0x007dc010 0x00000000 0x00000000 0x00000000
+				0x00000000 0x00000000 0x00000000 0x00000000>;
 		};
 
-	serial@70006200 {
-		status = "disable";
+		emc-table@380000 {
+			reg = <380000>;
+			compatible = "nvidia,tegra20-emc-table";
+			clock-frequency = <380000>;
+			nvidia,emc-registers = <0x00000017 0x0000004b
+				0x00000012 0x00000006 0x00000004 0x00000005
+				0x00000003 0x0000000c 0x00000006 0x00000006
+				0x00000003 0x00000001 0x00000004 0x00000005
+				0x00000004 0x00000009 0x0000000d 0x00000b5f
+				0x00000000 0x00000003 0x00000003 0x00000006
+				0x00000006 0x00000001 0x00000011 0x000000c8
+				0x00000003 0x0000000e 0x00000007 0x0000000f
+				0x00000002 0x00000000 0x00000000 0x00000002
+				0x00000000 0x00000000 0x00000083 0xe044048b
+				0x007d8010 0x00000000 0x00000000 0x00000000
+				0x00000000 0x00000000 0x00000000 0x00000000>;
 		};
-
-	serial@70006300 {
-		clock-frequency = < 216000000 >;
 	};
 
-	serial@70006400 {
-		status = "disable";
+	usb@c5000000 {
+		status = "okay";
+		nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
+		dr_mode = "otg";
 	};
 
-	sdhci@c8000000 {
-		status = "disable";
+	usb@c5004000 {
+		status = "okay";
+		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
 	};
 
-	sdhci@c8000200 {
-		status = "disable";
+	usb@c5008000 {
+		status = "okay";
 	};
 
 	sdhci@c8000400 {
+		status = "okay";
 		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
 		wp-gpios = <&gpio 57 0>; /* gpio PH1 */
 		power-gpios = <&gpio 70 0>; /* gpio PI6 */
@@ -351,15 +396,11 @@ sdhci@c8000400 {
 	};
 
 	sdhci@c8000600 {
+		status = "okay";
 		support-8bit;
 		bus-width = <8>;
 	};
 
-	usb@c5000000 {
-		nvidia,vbus-gpio = <&gpio 24 0>; /* PD0 */
-		dr_mode = "otg";
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 
@@ -380,45 +421,25 @@ lid {
 		};
 	};
 
-	emc@7000f400 {
-		emc-table@190000 {
-			reg = < 190000 >;
-			compatible = "nvidia,tegra20-emc-table";
-			clock-frequency = < 190000 >;
-			nvidia,emc-registers = < 0x0000000c 0x00000026
-				0x00000009 0x00000003 0x00000004 0x00000004
-				0x00000002 0x0000000c 0x00000003 0x00000003
-				0x00000002 0x00000001 0x00000004 0x00000005
-				0x00000004 0x00000009 0x0000000d 0x0000059f
-				0x00000000 0x00000003 0x00000003 0x00000003
-				0x00000003 0x00000001 0x0000000b 0x000000c8
-				0x00000003 0x00000007 0x00000004 0x0000000f
-				0x00000002 0x00000000 0x00000000 0x00000002
-				0x00000000 0x00000000 0x00000083 0xa06204ae
-				0x007dc010 0x00000000 0x00000000 0x00000000
-				0x00000000 0x00000000 0x00000000 0x00000000 >;
-		};
+	sound {
+		compatible = "nvidia,tegra-audio-wm8903-seaboard",
+			     "nvidia,tegra-audio-wm8903";
+		nvidia,model = "NVIDIA Tegra Seaboard";
 
-		emc-table@380000 {
-			reg = < 380000 >;
-			compatible = "nvidia,tegra20-emc-table";
-			clock-frequency = < 380000 >;
-			nvidia,emc-registers = < 0x00000017 0x0000004b
-				0x00000012 0x00000006 0x00000004 0x00000005
-				0x00000003 0x0000000c 0x00000006 0x00000006
-				0x00000003 0x00000001 0x00000004 0x00000005
-				0x00000004 0x00000009 0x0000000d 0x00000b5f
-				0x00000000 0x00000003 0x00000003 0x00000006
-				0x00000006 0x00000001 0x00000011 0x000000c8
-				0x00000003 0x0000000e 0x00000007 0x0000000f
-				0x00000002 0x00000000 0x00000000 0x00000002
-				0x00000000 0x00000000 0x00000083 0xe044048b
-				0x007d8010 0x00000000 0x00000000 0x00000000
-				0x00000000 0x00000000 0x00000000 0x00000000 >;
-		};
-	};
+		nvidia,audio-routing =
+			"Headphone Jack", "HPOUTR",
+			"Headphone Jack", "HPOUTL",
+			"Int Spk", "ROP",
+			"Int Spk", "RON",
+			"Int Spk", "LOP",
+			"Int Spk", "LON",
+			"Mic Jack", "MICBIAS",
+			"IN1R", "Mic Jack";
 
-	usb@c5004000 {
-		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&wm8903>;
+
+		nvidia,spkr-en-gpios = <&wm8903 2 0>;
+		nvidia,hp-det-gpios = <&gpio 185 0>; /* gpio PX1 */
 	};
 };

arch/arm/boot/dts/tegra-trimslice.dts

@@ -6,11 +6,11 @@ / {
 	model = "Compulab TrimSlice board";
 	compatible = "compulab,trimslice", "nvidia,tegra20";
 
-	memory@0 {
-		reg = < 0x00000000 0x40000000 >;
+	memory {
+		reg = <0x00000000 0x40000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -240,72 +240,67 @@ conf_ld17_0 {
 		};
 	};
 
+	i2s@70002800 {
+		status = "okay";
+	};
+
+	serial@70006000 {
+		status = "okay";
+		clock-frequency = <216000000>;
+	};
+
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000c400 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000c500 {
+		status = "okay";
 		clock-frequency = <400000>;
-	};
-
-	i2c@7000d000 {
-		status = "disable";
-	};
-
-	i2s@70002800 {
-		status = "disable";
-	};
 
-	i2s@70002a00 {
-		status = "disable";
+		codec: codec@1a {
+			compatible = "ti,tlv320aic23";
+			reg = <0x1a>;
 		};
 
-	das@70000c00 {
-		status = "disable";
+		rtc@56 {
+			compatible = "emmicro,em3027";
+			reg = <0x56>;
 		};
-
-	serial@70006000 {
-		clock-frequency = < 216000000 >;
-	};
-
-	serial@70006040 {
-		status = "disable";
 	};
 
-	serial@70006200 {
-		status = "disable";
+	usb@c5000000 {
+		status = "okay";
 	};
 
-	serial@70006300 {
-		status = "disable";
+	usb@c5004000 {
+		nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
 	};
 
-	serial@70006400 {
-		status = "disable";
+	usb@c5008000 {
+		status = "okay";
 	};
 
 	sdhci@c8000000 {
-		status = "disable";
-	};
-
-	sdhci@c8000200 {
-		status = "disable";
-	};
-
-	sdhci@c8000400 {
-		status = "disable";
+		status = "okay";
+		bus-width = <4>;
 	};
 
 	sdhci@c8000600 {
-		cd-gpios = <&gpio 121 0>;
-		wp-gpios = <&gpio 122 0>;
+		status = "okay";
+		cd-gpios = <&gpio 121 0>; /* gpio PP1 */
+		wp-gpios = <&gpio 122 0>; /* gpio PP2 */
+		bus-width = <4>;
 	};
 
-	usb@c5004000 {
-		nvidia,phy-reset-gpio = <&gpio 168 0>; /* gpio PV0 */
+	sound {
+		compatible = "nvidia,tegra-audio-trimslice";
+		nvidia,i2s-controller = <&tegra_i2s1>;
+		nvidia,audio-codec = <&codec>;
 	};
 };

arch/arm/boot/dts/tegra-ventana.dts

@@ -7,10 +7,10 @@ / {
 	compatible = "nvidia,ventana", "nvidia,tegra20";
 
 	memory {
-		reg = < 0x00000000 0x40000000 >;
+		reg = <0x00000000 0x40000000>;
 	};
 
-	pinmux@70000000 {
+	pinmux {
 		pinctrl-names = "default";
 		pinctrl-0 = <&state_default>;
 
@@ -240,38 +240,82 @@ conf_ld17_0 {
 		};
 	};
 
+	i2s@70002800 {
+		status = "okay";
+	};
+
+	serial@70006300 {
+		status = "okay";
+		clock-frequency = <216000000>;
+	};
+
 	i2c@7000c000 {
+		status = "okay";
 		clock-frequency = <400000>;
 
 		wm8903: wm8903@1a {
 			compatible = "wlf,wm8903";
 			reg = <0x1a>;
 			interrupt-parent = <&gpio>;
-			interrupts = < 187 0x04 >;
+			interrupts = <187 0x04>;
 
 			gpio-controller;
 			#gpio-cells = <2>;
 
 			micdet-cfg = <0>;
 			micdet-delay = <100>;
-			gpio-cfg = < 0xffffffff 0xffffffff 0 0xffffffff 0xffffffff >;
+			gpio-cfg = <0xffffffff 0xffffffff 0 0xffffffff 0xffffffff>;
+		};
+
+		/* ALS and proximity sensor */
+		isl29018@44 {
+			compatible = "isil,isl29018";
+			reg = <0x44>;
+			interrupt-parent = <&gpio>;
+			interrupts = <202 0x04>; /*gpio PZ2 */
 		};
 	};
 
 	i2c@7000c400 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000c500 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
 	i2c@7000d000 {
+		status = "okay";
 		clock-frequency = <400000>;
 	};
 
-	i2s@70002a00 {
-		status = "disable";
+	usb@c5000000 {
+		status = "okay";
+	};
+
+	usb@c5004000 {
+		status = "okay";
+		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
+	};
+
+	usb@c5008000 {
+		status = "okay";
+	};
+
+	sdhci@c8000400 {
+		status = "okay";
+		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
+		wp-gpios = <&gpio 57 0>; /* gpio PH1 */
+		power-gpios = <&gpio 70 0>; /* gpio PI6 */
+		bus-width = <4>;
+	};
+
+	sdhci@c8000600 {
+		status = "okay";
+		support-8bit;
+		bus-width = <8>;
 	};
 
 	sound {
@@ -294,51 +338,7 @@ sound {
 
 		nvidia,spkr-en-gpios = <&wm8903 2 0>;
 		nvidia,hp-det-gpios = <&gpio 178 0>; /* gpio PW2 */
-		nvidia,int-mic-en-gpios = <&gpio 184 0>; /*gpio PX0 */
+		nvidia,int-mic-en-gpios = <&gpio 184 0>; /* gpio PX0 */
 		nvidia,ext-mic-en-gpios = <&gpio 185 0>; /* gpio PX1 */
 	};
-
-	serial@70006000 {
-		status = "disable";
-	};
-
-	serial@70006040 {
-		status = "disable";
-	};
-
-	serial@70006200 {
-		status = "disable";
-	};
-
-	serial@70006300 {
-		clock-frequency = < 216000000 >;
-	};
-
-	serial@70006400 {
-		status = "disable";
-	};
-
-	sdhci@c8000000 {
-		status = "disable";
-	};
-
-	sdhci@c8000200 {
-		status = "disable";
-	};
-
-	sdhci@c8000400 {
-		cd-gpios = <&gpio 69 0>; /* gpio PI5 */
-		wp-gpios = <&gpio 57 0>; /* gpio PH1 */
-		power-gpios = <&gpio 70 0>; /* gpio PI6 */
-		bus-width = <4>;
-	};
-
-	sdhci@c8000600 {
-		support-8bit;
-		bus-width = <8>;
-	};
-
-	usb@c5004000 {
-		nvidia,phy-reset-gpio = <&gpio 169 0>; /* gpio PV1 */
-	};
 };

arch/arm/boot/dts/tegra20.dtsi

@@ -4,29 +4,18 @@ / {
 	compatible = "nvidia,tegra20";
 	interrupt-parent = <&intc>;
 
-	pmc@7000f400 {
-		compatible = "nvidia,tegra20-pmc";
-		reg = <0x7000e400 0x400>;
-	};
-
-	intc: interrupt-controller@50041000 {
+	intc: interrupt-controller {
 		compatible = "arm,cortex-a9-gic";
+		reg = <0x50041000 0x1000
+		       0x50040100 0x0100>;
 		interrupt-controller;
 		#interrupt-cells = <3>;
-		reg = < 0x50041000 0x1000 >,
-		      < 0x50040100 0x0100 >;
-	};
-
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <0 56 0x04
-			      0 57 0x04>;
 	};
 
-	apbdma: dma@6000a000 {
+	apbdma: dma {
 		compatible = "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1200>;
-		interrupts = < 0 104 0x04
+		interrupts = <0 104 0x04
 			      0 105 0x04
 			      0 106 0x04
 			      0 107 0x04
@@ -41,170 +30,216 @@ apbdma: dma@6000a000 {
 			      0 116 0x04
 			      0 117 0x04
 			      0 118 0x04
-			       0 119 0x04 >;
-	};
-
-	i2c@7000c000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra20-i2c";
-		reg = <0x7000C000 0x100>;
-		interrupts = < 0 38 0x04 >;
-	};
-
-	i2c@7000c400 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra20-i2c";
-		reg = <0x7000C400 0x100>;
-		interrupts = < 0 84 0x04 >;
-	};
-
-	i2c@7000c500 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra20-i2c";
-		reg = <0x7000C500 0x100>;
-		interrupts = < 0 92 0x04 >;
-	};
-
-	i2c@7000d000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra20-i2c-dvc";
-		reg = <0x7000D000 0x200>;
-		interrupts = < 0 53 0x04 >;
-	};
-
-	tegra_i2s1: i2s@70002800 {
-		compatible = "nvidia,tegra20-i2s";
-		reg = <0x70002800 0x200>;
-		interrupts = < 0 13 0x04 >;
-		nvidia,dma-request-selector = < &apbdma 2 >;
-	};
-
-	tegra_i2s2: i2s@70002a00 {
-		compatible = "nvidia,tegra20-i2s";
-		reg = <0x70002a00 0x200>;
-		interrupts = < 0 3 0x04 >;
-		nvidia,dma-request-selector = < &apbdma 1 >;
+			      0 119 0x04>;
 	};
 
-	das@70000c00 {
-		compatible = "nvidia,tegra20-das";
-		reg = <0x70000c00 0x80>;
+	ahb {
+		compatible = "nvidia,tegra20-ahb";
+		reg = <0x6000c004 0x10c>; /* AHB Arbitration + Gizmo Controller */
 	};
 
-	gpio: gpio@6000d000 {
+	gpio: gpio {
 		compatible = "nvidia,tegra20-gpio";
-		reg = < 0x6000d000 0x1000 >;
-		interrupts = < 0 32 0x04
+		reg = <0x6000d000 0x1000>;
+		interrupts = <0 32 0x04
 			      0 33 0x04
 			      0 34 0x04
 			      0 35 0x04
 			      0 55 0x04
 			      0 87 0x04
-			       0 89 0x04 >;
+			      0 89 0x04>;
 		#gpio-cells = <2>;
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
 	};
 
-	pinmux: pinmux@70000000 {
+	pinmux: pinmux {
 		compatible = "nvidia,tegra20-pinmux";
-		reg = < 0x70000014 0x10    /* Tri-state registers */
+		reg = <0x70000014 0x10   /* Tri-state registers */
 		       0x70000080 0x20   /* Mux registers */
 		       0x700000a0 0x14   /* Pull-up/down registers */
-			0x70000868 0xa8 >; /* Pad control registers */
+		       0x70000868 0xa8>; /* Pad control registers */
+	};
+
+	das {
+		compatible = "nvidia,tegra20-das";
+		reg = <0x70000c00 0x80>;
+	};
+
+	tegra_i2s1: i2s@70002800 {
+		compatible = "nvidia,tegra20-i2s";
+		reg = <0x70002800 0x200>;
+		interrupts = <0 13 0x04>;
+		nvidia,dma-request-selector = <&apbdma 2>;
+		status = "disable";
+	};
+
+	tegra_i2s2: i2s@70002a00 {
+		compatible = "nvidia,tegra20-i2s";
+		reg = <0x70002a00 0x200>;
+		interrupts = <0 3 0x04>;
+		nvidia,dma-request-selector = <&apbdma 1>;
+		status = "disable";
 	};
 
 	serial@70006000 {
 		compatible = "nvidia,tegra20-uart";
 		reg = <0x70006000 0x40>;
 		reg-shift = <2>;
-		interrupts = < 0 36 0x04 >;
+		interrupts = <0 36 0x04>;
+		status = "disable";
 	};
 
 	serial@70006040 {
 		compatible = "nvidia,tegra20-uart";
 		reg = <0x70006040 0x40>;
 		reg-shift = <2>;
-		interrupts = < 0 37 0x04 >;
+		interrupts = <0 37 0x04>;
+		status = "disable";
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra20-uart";
 		reg = <0x70006200 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 46 0x04 >;
+		interrupts = <0 46 0x04>;
+		status = "disable";
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra20-uart";
 		reg = <0x70006300 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 90 0x04 >;
+		interrupts = <0 90 0x04>;
+		status = "disable";
 	};
 
 	serial@70006400 {
 		compatible = "nvidia,tegra20-uart";
 		reg = <0x70006400 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 91 0x04 >;
+		interrupts = <0 91 0x04>;
+		status = "disable";
 	};
 
-	emc@7000f400 {
+	i2c@7000c000 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
 		#address-cells = <1>;
 		#size-cells = <0>;
-		compatible = "nvidia,tegra20-emc";
-		reg = <0x7000f400 0x200>;
+		status = "disable";
 	};
 
-	sdhci@c8000000 {
-		compatible = "nvidia,tegra20-sdhci";
-		reg = <0xc8000000 0x200>;
-		interrupts = < 0 14 0x04 >;
+	i2c@7000c400 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c400 0x100>;
+		interrupts = <0 84 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@c8000200 {
-		compatible = "nvidia,tegra20-sdhci";
-		reg = <0xc8000200 0x200>;
-		interrupts = < 0 15 0x04 >;
+	i2c@7000c500 {
+		compatible = "nvidia,tegra20-i2c";
+		reg = <0x7000c500 0x100>;
+		interrupts = <0 92 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@c8000400 {
-		compatible = "nvidia,tegra20-sdhci";
-		reg = <0xc8000400 0x200>;
-		interrupts = < 0 19 0x04 >;
+	i2c@7000d000 {
+		compatible = "nvidia,tegra20-i2c-dvc";
+		reg = <0x7000d000 0x200>;
+		interrupts = <0 53 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@c8000600 {
-		compatible = "nvidia,tegra20-sdhci";
-		reg = <0xc8000600 0x200>;
-		interrupts = < 0 31 0x04 >;
+	pmc {
+		compatible = "nvidia,tegra20-pmc";
+		reg = <0x7000e400 0x400>;
+	};
+
+	mc {
+		compatible = "nvidia,tegra20-mc";
+		reg = <0x7000f000 0x024
+		       0x7000f03c 0x3c4>;
+		interrupts = <0 77 0x04>;
+	};
+
+	gart {
+		compatible = "nvidia,tegra20-gart";
+		reg = <0x7000f024 0x00000018	/* controller registers */
+		       0x58000000 0x02000000>;	/* GART aperture */
+	};
+
+	emc {
+		compatible = "nvidia,tegra20-emc";
+		reg = <0x7000f400 0x200>;
+		#address-cells = <1>;
+		#size-cells = <0>;
 	};
 
 	usb@c5000000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5000000 0x4000>;
-		interrupts = < 0 20 0x04 >;
+		interrupts = <0 20 0x04>;
 		phy_type = "utmi";
 		nvidia,has-legacy-mode;
+		status = "disable";
 	};
 
 	usb@c5004000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5004000 0x4000>;
-		interrupts = < 0 21 0x04 >;
+		interrupts = <0 21 0x04>;
 		phy_type = "ulpi";
+		status = "disable";
 	};
 
 	usb@c5008000 {
 		compatible = "nvidia,tegra20-ehci", "usb-ehci";
 		reg = <0xc5008000 0x4000>;
-		interrupts = < 0 97 0x04 >;
+		interrupts = <0 97 0x04>;
 		phy_type = "utmi";
+		status = "disable";
+	};
+
+	sdhci@c8000000 {
+		compatible = "nvidia,tegra20-sdhci";
+		reg = <0xc8000000 0x200>;
+		interrupts = <0 14 0x04>;
+		status = "disable";
+	};
+
+	sdhci@c8000200 {
+		compatible = "nvidia,tegra20-sdhci";
+		reg = <0xc8000200 0x200>;
+		interrupts = <0 15 0x04>;
+		status = "disable";
 	};
-};
 
+	sdhci@c8000400 {
+		compatible = "nvidia,tegra20-sdhci";
+		reg = <0xc8000400 0x200>;
+		interrupts = <0 19 0x04>;
+		status = "disable";
+	};
+
+	sdhci@c8000600 {
+		compatible = "nvidia,tegra20-sdhci";
+		reg = <0xc8000600 0x200>;
+		interrupts = <0 31 0x04>;
+		status = "disable";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <0 56 0x04
+			      0 57 0x04>;
+	};
+};

arch/arm/boot/dts/tegra30.dtsi

@@ -4,31 +4,18 @@ / {
 	compatible = "nvidia,tegra30";
 	interrupt-parent = <&intc>;
 
-	pmc@7000f400 {
-		compatible = "nvidia,tegra20-pmc", "nvidia,tegra30-pmc";
-		reg = <0x7000e400 0x400>;
-	};
-
-	intc: interrupt-controller@50041000 {
+	intc: interrupt-controller {
 		compatible = "arm,cortex-a9-gic";
+		reg = <0x50041000 0x1000
+		       0x50040100 0x0100>;
 		interrupt-controller;
 		#interrupt-cells = <3>;
-		reg = < 0x50041000 0x1000 >,
-		      < 0x50040100 0x0100 >;
 	};
 
-	pmu {
-		compatible = "arm,cortex-a9-pmu";
-		interrupts = <0 144 0x04
-			      0 145 0x04
-			      0 146 0x04
-			      0 147 0x04>;
-	};
-
-	apbdma: dma@6000a000 {
+	apbdma: dma {
 		compatible = "nvidia,tegra30-apbdma", "nvidia,tegra20-apbdma";
 		reg = <0x6000a000 0x1400>;
-		interrupts = < 0 104 0x04
+		interrupts = <0 104 0x04
 			      0 105 0x04
 			      0 106 0x04
 			      0 107 0x04
@@ -59,135 +46,151 @@ apbdma: dma@6000a000 {
 			      0 140 0x04
 			      0 141 0x04
 			      0 142 0x04
-			       0 143 0x04 >;
+			      0 143 0x04>;
 	};
 
-	i2c@7000c000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible =  "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
-		reg = <0x7000C000 0x100>;
-		interrupts = < 0 38 0x04 >;
-	};
-
-	i2c@7000c400 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
-		reg = <0x7000C400 0x100>;
-		interrupts = < 0 84 0x04 >;
+	ahb: ahb {
+		compatible = "nvidia,tegra30-ahb";
+		reg = <0x6000c004 0x14c>; /* AHB Arbitration + Gizmo Controller */
 	};
 
-	i2c@7000c500 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
-		reg = <0x7000C500 0x100>;
-		interrupts = < 0 92 0x04 >;
-	};
-
-	i2c@7000c700 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
-		reg = <0x7000c700 0x100>;
-		interrupts = < 0 120 0x04 >;
-	};
-
-	i2c@7000d000 {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
-		reg = <0x7000D000 0x100>;
-		interrupts = < 0 53 0x04 >;
-	};
-
-	gpio: gpio@6000d000 {
+	gpio: gpio {
 		compatible = "nvidia,tegra30-gpio", "nvidia,tegra20-gpio";
-		reg = < 0x6000d000 0x1000 >;
-		interrupts = < 0 32 0x04
+		reg = <0x6000d000 0x1000>;
+		interrupts = <0 32 0x04
 			      0 33 0x04
 			      0 34 0x04
 			      0 35 0x04
 			      0 55 0x04
 			      0 87 0x04
 			      0 89 0x04
-			       0 125 0x04 >;
+			      0 125 0x04>;
 		#gpio-cells = <2>;
 		gpio-controller;
 		#interrupt-cells = <2>;
 		interrupt-controller;
 	};
 
+	pinmux: pinmux {
+		compatible = "nvidia,tegra30-pinmux";
+		reg = <0x70000868 0xd0    /* Pad control registers */
+		       0x70003000 0x3e0>; /* Mux registers */
+	};
+
 	serial@70006000 {
 		compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
 		reg = <0x70006000 0x40>;
 		reg-shift = <2>;
-		interrupts = < 0 36 0x04 >;
+		interrupts = <0 36 0x04>;
+		status = "disable";
 	};
 
 	serial@70006040 {
 		compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
 		reg = <0x70006040 0x40>;
 		reg-shift = <2>;
-		interrupts = < 0 37 0x04 >;
+		interrupts = <0 37 0x04>;
+		status = "disable";
 	};
 
 	serial@70006200 {
 		compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
 		reg = <0x70006200 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 46 0x04 >;
+		interrupts = <0 46 0x04>;
+		status = "disable";
 	};
 
 	serial@70006300 {
 		compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
 		reg = <0x70006300 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 90 0x04 >;
+		interrupts = <0 90 0x04>;
+		status = "disable";
 	};
 
 	serial@70006400 {
 		compatible = "nvidia,tegra30-uart", "nvidia,tegra20-uart";
 		reg = <0x70006400 0x100>;
 		reg-shift = <2>;
-		interrupts = < 0 91 0x04 >;
+		interrupts = <0 91 0x04>;
+		status = "disable";
 	};
 
-	sdhci@78000000 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
-		reg = <0x78000000 0x200>;
-		interrupts = < 0 14 0x04 >;
+	i2c@7000c000 {
+		compatible =  "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+		reg = <0x7000c000 0x100>;
+		interrupts = <0 38 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@78000200 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
-		reg = <0x78000200 0x200>;
-		interrupts = < 0 15 0x04 >;
+	i2c@7000c400 {
+		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+		reg = <0x7000c400 0x100>;
+		interrupts = <0 84 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@78000400 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
-		reg = <0x78000400 0x200>;
-		interrupts = < 0 19 0x04 >;
+	i2c@7000c500 {
+		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+		reg = <0x7000c500 0x100>;
+		interrupts = <0 92 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	sdhci@78000600 {
-		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
-		reg = <0x78000600 0x200>;
-		interrupts = < 0 31 0x04 >;
+	i2c@7000c700 {
+		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+		reg = <0x7000c700 0x100>;
+		interrupts = <0 120 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
 	};
 
-	pinmux: pinmux@70000000 {
-		compatible = "nvidia,tegra30-pinmux";
-		reg = < 0x70000868 0xd0     /* Pad control registers */
-			0x70003000 0x3e0 >; /* Mux registers */
+	i2c@7000d000 {
+		compatible = "nvidia,tegra30-i2c", "nvidia,tegra20-i2c";
+		reg = <0x7000d000 0x100>;
+		interrupts = <0 53 0x04>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "disable";
+	};
+
+	pmc {
+		compatible = "nvidia,tegra20-pmc", "nvidia,tegra30-pmc";
+		reg = <0x7000e400 0x400>;
+	};
+
+	mc {
+		compatible = "nvidia,tegra30-mc";
+		reg = <0x7000f000 0x010
+		       0x7000f03c 0x1b4
+		       0x7000f200 0x028
+		       0x7000f284 0x17c>;
+		interrupts = <0 77 0x04>;
+	};
+
+	smmu {
+		compatible = "nvidia,tegra30-smmu";
+		reg = <0x7000f010 0x02c
+		       0x7000f1f0 0x010
+		       0x7000f228 0x05c>;
+		nvidia,#asids = <4>;		/* # of ASIDs */
+		dma-window = <0 0x40000000>;	/* IOVA start & length */
+		nvidia,ahb = <&ahb>;
 	};
 
 	ahub {
 		compatible = "nvidia,tegra30-ahub";
-		reg = <0x70080000 0x200 0x70080200 0x100>;
-		interrupts = < 0 103 0x04 >;
+		reg = <0x70080000 0x200
+		       0x70080200 0x100>;
+		interrupts = <0 103 0x04>;
 		nvidia,dma-request-selector = <&apbdma 1>;
 
 		ranges;
@@ -198,30 +201,71 @@ tegra_i2s0: i2s@70080300 {
 			compatible = "nvidia,tegra30-i2s";
 			reg = <0x70080300 0x100>;
 			nvidia,ahub-cif-ids = <4 4>;
+			status = "disable";
 		};
 
 		tegra_i2s1: i2s@70080400 {
 			compatible = "nvidia,tegra30-i2s";
 			reg = <0x70080400 0x100>;
 			nvidia,ahub-cif-ids = <5 5>;
+			status = "disable";
 		};
 
 		tegra_i2s2: i2s@70080500 {
 			compatible = "nvidia,tegra30-i2s";
 			reg = <0x70080500 0x100>;
 			nvidia,ahub-cif-ids = <6 6>;
+			status = "disable";
 		};
 
 		tegra_i2s3: i2s@70080600 {
 			compatible = "nvidia,tegra30-i2s";
 			reg = <0x70080600 0x100>;
 			nvidia,ahub-cif-ids = <7 7>;
+			status = "disable";
 		};
 
 		tegra_i2s4: i2s@70080700 {
 			compatible = "nvidia,tegra30-i2s";
 			reg = <0x70080700 0x100>;
 			nvidia,ahub-cif-ids = <8 8>;
+			status = "disable";
 		};
 	};
+
+	sdhci@78000000 {
+		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+		reg = <0x78000000 0x200>;
+		interrupts = <0 14 0x04>;
+		status = "disable";
+	};
+
+	sdhci@78000200 {
+		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+		reg = <0x78000200 0x200>;
+		interrupts = <0 15 0x04>;
+		status = "disable";
+	};
+
+	sdhci@78000400 {
+		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+		reg = <0x78000400 0x200>;
+		interrupts = <0 19 0x04>;
+		status = "disable";
+	};
+
+	sdhci@78000600 {
+		compatible = "nvidia,tegra30-sdhci", "nvidia,tegra20-sdhci";
+		reg = <0x78000600 0x200>;
+		interrupts = <0 31 0x04>;
+		status = "disable";
+	};
+
+	pmu {
+		compatible = "arm,cortex-a9-pmu";
+		interrupts = <0 144 0x04
+			      0 145 0x04
+			      0 146 0x04
+			      0 147 0x04>;
+	};
 };

arch/arm/configs/mxs_defconfig

@@ -22,6 +22,7 @@ CONFIG_BLK_DEV_INTEGRITY=y
 # CONFIG_IOSCHED_DEADLINE is not set
 # CONFIG_IOSCHED_CFQ is not set
 CONFIG_ARCH_MXS=y
+CONFIG_MACH_MXS_DT=y
 CONFIG_MACH_MX23EVK=y
 CONFIG_MACH_MX28EVK=y
 CONFIG_MACH_STMP378X_DEVB=y

arch/arm/mach-imx/Makefile.boot

@@ -42,4 +42,5 @@ dtb-$(CONFIG_MACH_IMX51_DT) += imx51-babbage.dtb
 dtb-$(CONFIG_MACH_IMX53_DT) += imx53-ard.dtb imx53-evk.dtb \
 			       imx53-qsb.dtb imx53-smd.dtb
 dtb-$(CONFIG_SOC_IMX6Q)	+= imx6q-arm2.dtb \
-			   imx6q-sabrelite.dtb
+			   imx6q-sabrelite.dtb \
+			   imx6q-sabresd.dtb \

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -31,6 +31,11 @@ static const char *per_lp_apm_sel[] = { "main_bus", "lp_apm", };
 static const char *per_root_sel[] = { "per_podf", "ipg", };
 static const char *esdhc_c_sel[] = { "esdhc_a_podf", "esdhc_b_podf", };
 static const char *esdhc_d_sel[] = { "esdhc_a_podf", "esdhc_b_podf", };
+static const char *ssi_apm_sels[] = { "ckih1", "lp_amp", "ckih2", };
+static const char *ssi_clk_sels[] = { "pll1_sw", "pll2_sw", "pll3_sw", "ssi_apm", };
+static const char *ssi3_clk_sels[] = { "ssi1_root_gate", "ssi2_root_gate", };
+static const char *ssi_ext1_com_sels[] = { "ssi_ext1_podf", "ssi1_root_gate", };
+static const char *ssi_ext2_com_sels[] = { "ssi_ext2_podf", "ssi2_root_gate", };
 static const char *emi_slow_sel[] = { "main_bus", "ahb", };
 static const char *usb_phy_sel_str[] = { "osc", "usb_phy_podf", };
 static const char *mx51_ipu_di0_sel[] = { "di_pred", "osc", "ckih1", "tve_di", };
@@ -71,6 +76,11 @@ enum imx5_clks {
 	pll3_sw, ipu_di0_sel, ipu_di1_sel, tve_ext_sel, mx51_mipi, pll4_sw,
 	ldb_di1_sel, di_pll4_podf, ldb_di0_sel, ldb_di0_gate, usb_phy1_gate,
 	usb_phy2_gate, per_lp_apm, per_pred1, per_pred2, per_podf, per_root,
+	ssi_apm, ssi1_root_sel, ssi2_root_sel, ssi3_root_sel, ssi_ext1_sel,
+	ssi_ext2_sel, ssi_ext1_com_sel, ssi_ext2_com_sel, ssi1_root_pred,
+	ssi1_root_podf, ssi2_root_pred, ssi2_root_podf, ssi_ext1_pred,
+	ssi_ext1_podf, ssi_ext2_pred, ssi_ext2_podf, ssi1_root_gate,
+	ssi2_root_gate, ssi3_root_gate, ssi_ext1_gate, ssi_ext2_gate,
 	clk_max
 };
 
@@ -195,6 +205,28 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk[uart5_per_gate] = imx_clk_gate2("uart5_per_gate", "uart_root", MXC_CCM_CCGR7, 14);
 	clk[gpc_dvfs] = imx_clk_gate2("gpc_dvfs", "dummy", MXC_CCM_CCGR5, 24);
 
+	clk[ssi_apm] = imx_clk_mux("ssi_apm", MXC_CCM_CSCMR1, 8, 2, ssi_apm_sels, ARRAY_SIZE(ssi_apm_sels));
+	clk[ssi1_root_sel] = imx_clk_mux("ssi1_root_sel", MXC_CCM_CSCMR1, 14, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+	clk[ssi2_root_sel] = imx_clk_mux("ssi2_root_sel", MXC_CCM_CSCMR1, 12, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+	clk[ssi3_root_sel] = imx_clk_mux("ssi3_root_sel", MXC_CCM_CSCMR1, 11, 1, ssi3_clk_sels, ARRAY_SIZE(ssi3_clk_sels));
+	clk[ssi_ext1_sel] = imx_clk_mux("ssi_ext1_sel", MXC_CCM_CSCMR1, 28, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+	clk[ssi_ext2_sel] = imx_clk_mux("ssi_ext2_sel", MXC_CCM_CSCMR1, 30, 2, ssi_clk_sels, ARRAY_SIZE(ssi_clk_sels));
+	clk[ssi_ext1_com_sel] = imx_clk_mux("ssi_ext1_com_sel", MXC_CCM_CSCMR1, 0, 1, ssi_ext1_com_sels, ARRAY_SIZE(ssi_ext1_com_sels));
+	clk[ssi_ext2_com_sel] = imx_clk_mux("ssi_ext2_com_sel", MXC_CCM_CSCMR1, 1, 1, ssi_ext2_com_sels, ARRAY_SIZE(ssi_ext2_com_sels));
+	clk[ssi1_root_pred] = imx_clk_divider("ssi1_root_pred", "ssi1_root_sel", MXC_CCM_CS1CDR, 6, 3);
+	clk[ssi1_root_podf] = imx_clk_divider("ssi1_root_podf", "ssi1_root_pred", MXC_CCM_CS1CDR, 0, 6);
+	clk[ssi2_root_pred] = imx_clk_divider("ssi2_root_pred", "ssi2_root_sel", MXC_CCM_CS2CDR, 6, 3);
+	clk[ssi2_root_podf] = imx_clk_divider("ssi2_root_podf", "ssi2_root_pred", MXC_CCM_CS2CDR, 0, 6);
+	clk[ssi_ext1_pred] = imx_clk_divider("ssi_ext1_pred", "ssi_ext1_sel", MXC_CCM_CS1CDR, 22, 3);
+	clk[ssi_ext1_podf] = imx_clk_divider("ssi_ext1_podf", "ssi_ext1_pred", MXC_CCM_CS1CDR, 16, 6);
+	clk[ssi_ext2_pred] = imx_clk_divider("ssi_ext2_pred", "ssi_ext2_sel", MXC_CCM_CS2CDR, 22, 3);
+	clk[ssi_ext2_podf] = imx_clk_divider("ssi_ext2_podf", "ssi_ext2_pred", MXC_CCM_CS2CDR, 16, 6);
+	clk[ssi1_root_gate] = imx_clk_gate2("ssi1_root_gate", "ssi1_root_podf", MXC_CCM_CCGR3, 18);
+	clk[ssi2_root_gate] = imx_clk_gate2("ssi2_root_gate", "ssi2_root_podf", MXC_CCM_CCGR3, 22);
+	clk[ssi3_root_gate] = imx_clk_gate2("ssi3_root_gate", "ssi3_root_sel", MXC_CCM_CCGR3, 26);
+	clk[ssi_ext1_gate] = imx_clk_gate2("ssi_ext1_gate", "ssi_ext1_com_sel", MXC_CCM_CCGR3, 28);
+	clk[ssi_ext2_gate] = imx_clk_gate2("ssi_ext2_gate", "ssi_ext2_com_sel", MXC_CCM_CCGR3, 30);
+
 	for (i = 0; i < ARRAY_SIZE(clk); i++)
 		if (IS_ERR(clk[i]))
 			pr_err("i.MX5 clk %d: register failed with %ld\n",
@@ -237,6 +269,8 @@ static void __init mx5_clocks_common_init(unsigned long rate_ckil,
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "imx-ssi.0");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "imx-ssi.1");
 	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "imx-ssi.2");
+	clk_register_clkdev(clk[ssi_ext1_gate], "ssi_ext1", NULL);
+	clk_register_clkdev(clk[ssi_ext2_gate], "ssi_ext2", NULL);
 	clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
 	clk_register_clkdev(clk[cpu_podf], "cpu", NULL);
 	clk_register_clkdev(clk[iim_gate], "iim", NULL);
@@ -320,6 +354,9 @@ int __init mx51_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_register_clkdev(clk[esdhc4_ipg_gate], "ipg", "sdhci-esdhc-imx51.3");
 	clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx51.3");
 	clk_register_clkdev(clk[esdhc4_per_gate], "per", "sdhci-esdhc-imx51.3");
+	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "83fcc000.ssi");
+	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "70014000.ssi");
+	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "83fe8000.ssi");
 
 	/* set the usboh3 parent to pll2_sw */
 	clk_set_parent(clk[usboh3_sel], clk[pll2_sw]);
@@ -406,6 +443,9 @@ int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_register_clkdev(clk[esdhc4_ipg_gate], "ipg", "sdhci-esdhc-imx53.3");
 	clk_register_clkdev(clk[dummy], "ahb", "sdhci-esdhc-imx53.3");
 	clk_register_clkdev(clk[esdhc4_per_gate], "per", "sdhci-esdhc-imx53.3");
+	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "63fcc000.ssi");
+	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "50014000.ssi");
+	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "63fd0000.ssi");
 
 	/* set SDHC root clock to 200MHZ*/
 	clk_set_rate(clk[esdhc_a_podf], 200000000);

arch/arm/mach-imx/clk-imx6q.c

@@ -155,7 +155,8 @@ enum mx6q_clks {
 	gpmi_bch_apb, gpmi_bch, gpmi_io, gpmi_apb, sata, sdma, spba, ssi1,
 	ssi2, ssi3, uart_ipg, uart_serial, usboh3, usdhc1, usdhc2, usdhc3,
 	usdhc4, vdo_axi, vpu_axi, cko1, pll1_sys, pll2_bus, pll3_usb_otg,
-	pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, clk_max
+	pll4_audio, pll5_video, pll6_mlb, pll7_usb_host, pll8_enet, ssi1_ipg,
+	ssi2_ipg, ssi3_ipg, clk_max
 };
 
 static struct clk *clk[clk_max];
@@ -367,9 +368,9 @@ int __init mx6q_clocks_init(void)
 	clk[sata]         = imx_clk_gate2("sata",          "ipg",               base + 0x7c, 4);
 	clk[sdma]         = imx_clk_gate2("sdma",          "ahb",               base + 0x7c, 6);
 	clk[spba]         = imx_clk_gate2("spba",          "ipg",               base + 0x7c, 12);
-	clk[ssi1]         = imx_clk_gate2("ssi1",          "ssi1_podf",         base + 0x7c, 18);
-	clk[ssi2]         = imx_clk_gate2("ssi2",          "ssi2_podf",         base + 0x7c, 20);
-	clk[ssi3]         = imx_clk_gate2("ssi3",          "ssi3_podf",         base + 0x7c, 22);
+	clk[ssi1_ipg]     = imx_clk_gate2("ssi1_ipg",      "ipg",               base + 0x7c, 18);
+	clk[ssi2_ipg]     = imx_clk_gate2("ssi2_ipg",      "ipg",               base + 0x7c, 20);
+	clk[ssi3_ipg]     = imx_clk_gate2("ssi3_ipg",      "ipg",               base + 0x7c, 22);
 	clk[uart_ipg]     = imx_clk_gate2("uart_ipg",      "ipg",               base + 0x7c, 24);
 	clk[uart_serial]  = imx_clk_gate2("uart_serial",   "uart_serial_podf",  base + 0x7c, 26);
 	clk[usboh3]       = imx_clk_gate2("usboh3",        "ipg",               base + 0x80, 0);
@@ -392,17 +393,17 @@ int __init mx6q_clocks_init(void)
 	clk_register_clkdev(clk[gpt_ipg_per], "per", "imx-gpt.0");
 	clk_register_clkdev(clk[twd], NULL, "smp_twd");
 	clk_register_clkdev(clk[usboh3], NULL, "usboh3");
-	clk_register_clkdev(clk[uart_serial], "per", "2020000.uart");
-	clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.uart");
-	clk_register_clkdev(clk[uart_serial], "per", "21e8000.uart");
-	clk_register_clkdev(clk[uart_ipg], "ipg", "21e8000.uart");
-	clk_register_clkdev(clk[uart_serial], "per", "21ec000.uart");
-	clk_register_clkdev(clk[uart_ipg], "ipg", "21ec000.uart");
-	clk_register_clkdev(clk[uart_serial], "per", "21f0000.uart");
-	clk_register_clkdev(clk[uart_ipg], "ipg", "21f0000.uart");
-	clk_register_clkdev(clk[uart_serial], "per", "21f4000.uart");
-	clk_register_clkdev(clk[uart_ipg], "ipg", "21f4000.uart");
-	clk_register_clkdev(clk[enet], NULL, "2188000.enet");
+	clk_register_clkdev(clk[uart_serial], "per", "2020000.serial");
+	clk_register_clkdev(clk[uart_ipg], "ipg", "2020000.serial");
+	clk_register_clkdev(clk[uart_serial], "per", "21e8000.serial");
+	clk_register_clkdev(clk[uart_ipg], "ipg", "21e8000.serial");
+	clk_register_clkdev(clk[uart_serial], "per", "21ec000.serial");
+	clk_register_clkdev(clk[uart_ipg], "ipg", "21ec000.serial");
+	clk_register_clkdev(clk[uart_serial], "per", "21f0000.serial");
+	clk_register_clkdev(clk[uart_ipg], "ipg", "21f0000.serial");
+	clk_register_clkdev(clk[uart_serial], "per", "21f4000.serial");
+	clk_register_clkdev(clk[uart_ipg], "ipg", "21f4000.serial");
+	clk_register_clkdev(clk[enet], NULL, "2188000.ethernet");
 	clk_register_clkdev(clk[usdhc1], NULL, "2190000.usdhc");
 	clk_register_clkdev(clk[usdhc2], NULL, "2194000.usdhc");
 	clk_register_clkdev(clk[usdhc3], NULL, "2198000.usdhc");
@@ -418,6 +419,10 @@ int __init mx6q_clocks_init(void)
 	clk_register_clkdev(clk[sdma], NULL, "20ec000.sdma");
 	clk_register_clkdev(clk[dummy], NULL, "20bc000.wdog");
 	clk_register_clkdev(clk[dummy], NULL, "20c0000.wdog");
+	clk_register_clkdev(clk[ssi1_ipg], NULL, "2028000.ssi");
+	clk_register_clkdev(clk[cko1_sel], "cko1_sel", NULL);
+	clk_register_clkdev(clk[ahb], "ahb", NULL);
+	clk_register_clkdev(clk[cko1], "cko1", NULL);
 
 	for (i = 0; i < ARRAY_SIZE(clks_init_on); i++) {
 		c = clk_get_sys(clks_init_on[i], NULL);

arch/arm/mach-imx/imx53-dt.c

@@ -10,6 +10,9 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/irqdomain.h>
@@ -81,6 +84,19 @@ static const struct of_device_id imx53_iomuxc_of_match[] __initconst = {
 	{ /* sentinel */ }
 };
 
+static void __init imx53_qsb_init(void)
+{
+	struct clk *clk;
+
+	clk = clk_get_sys(NULL, "ssi_ext1");
+	if (IS_ERR(clk)) {
+		pr_err("failed to get clk ssi_ext1\n");
+		return;
+	}
+
+	clk_register_clkdev(clk, NULL, "0-000a");
+}
+
 static void __init imx53_dt_init(void)
 {
 	struct device_node *node;
@@ -99,6 +115,9 @@ static void __init imx53_dt_init(void)
 		of_node_put(node);
 	}
 
+	if (of_machine_is_compatible("fsl,imx53-qsb"))
+		imx53_qsb_init();
+
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     imx53_auxdata_lookup, NULL);
 }

arch/arm/mach-imx/lluart.c

@@ -17,6 +17,12 @@
 #include <mach/hardware.h>
 
 static struct map_desc imx_lluart_desc = {
+#ifdef CONFIG_DEBUG_IMX6Q_UART2
+	.virtual	= MX6Q_IO_P2V(MX6Q_UART2_BASE_ADDR),
+	.pfn		= __phys_to_pfn(MX6Q_UART2_BASE_ADDR),
+	.length		= MX6Q_UART2_SIZE,
+	.type		= MT_DEVICE,
+#endif
 #ifdef CONFIG_DEBUG_IMX6Q_UART4
 	.virtual	= MX6Q_IO_P2V(MX6Q_UART4_BASE_ADDR),
 	.pfn		= __phys_to_pfn(MX6Q_UART4_BASE_ADDR),

arch/arm/mach-imx/mach-imx6q.c

@@ -10,6 +10,8 @@
  * http://www.gnu.org/copyleft/gpl.html
  */
 
+#include <linux/clk.h>
+#include <linux/clkdev.h>
 #include <linux/delay.h>
 #include <linux/init.h>
 #include <linux/io.h>
@@ -64,6 +66,7 @@ void imx6q_restart(char mode, const char *cmd)
 /* For imx6q sabrelite board: set KSZ9021RN RGMII pad skew */
 static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 {
+	if (IS_ENABLED(CONFIG_PHYLIB)) {
 		/* min rx data delay */
 		phy_write(phydev, 0x0b, 0x8105);
 		phy_write(phydev, 0x0c, 0x0000);
@@ -72,10 +75,44 @@ static int ksz9021rn_phy_fixup(struct phy_device *phydev)
 		phy_write(phydev, 0x0b, 0x8104);
 		phy_write(phydev, 0x0c, 0xf0f0);
 		phy_write(phydev, 0x0b, 0x104);
+	}
 
 	return 0;
 }
 
+static void __init imx6q_sabrelite_cko1_setup(void)
+{
+	struct clk *cko1_sel, *ahb, *cko1;
+	unsigned long rate;
+
+	cko1_sel = clk_get_sys(NULL, "cko1_sel");
+	ahb = clk_get_sys(NULL, "ahb");
+	cko1 = clk_get_sys(NULL, "cko1");
+	if (IS_ERR(cko1_sel) || IS_ERR(ahb) || IS_ERR(cko1)) {
+		pr_err("cko1 setup failed!\n");
+		goto put_clk;
+	}
+	clk_set_parent(cko1_sel, ahb);
+	rate = clk_round_rate(cko1, 16000000);
+	clk_set_rate(cko1, rate);
+	clk_register_clkdev(cko1, NULL, "0-000a");
+put_clk:
+	if (!IS_ERR(cko1_sel))
+		clk_put(cko1_sel);
+	if (!IS_ERR(ahb))
+		clk_put(ahb);
+	if (!IS_ERR(cko1))
+		clk_put(cko1);
+}
+
+static void __init imx6q_sabrelite_init(void)
+{
+	if (IS_ENABLED(CONFIG_PHYLIB))
+		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
+				ksz9021rn_phy_fixup);
+	imx6q_sabrelite_cko1_setup();
+}
+
 static void __init imx6q_init_machine(void)
 {
 	/*
@@ -85,8 +122,7 @@ static void __init imx6q_init_machine(void)
 	pinctrl_provide_dummies();
 
 	if (of_machine_is_compatible("fsl,imx6q-sabrelite"))
-		phy_register_fixup_for_uid(PHY_ID_KSZ9021, MICREL_PHY_ID_MASK,
-					   ksz9021rn_phy_fixup);
+		imx6q_sabrelite_init();
 
 	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 
@@ -139,6 +175,7 @@ static struct sys_timer imx6q_timer = {
 static const char *imx6q_dt_compat[] __initdata = {
 	"fsl,imx6q-arm2",
 	"fsl,imx6q-sabrelite",
+	"fsl,imx6q-sabresd",
 	"fsl,imx6q",
 	NULL,
 };

arch/arm/mach-imx/mach-mx51_babbage.c

@@ -163,6 +163,12 @@ static iomux_v3_cfg_t mx51babbage_pads[] = {
 	MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK,
 	MX51_PAD_CSPI1_SS0__GPIO4_24,
 	MX51_PAD_CSPI1_SS1__GPIO4_25,
+
+	/* Audio */
+	MX51_PAD_AUD3_BB_TXD__AUD3_TXD,
+	MX51_PAD_AUD3_BB_RXD__AUD3_RXD,
+	MX51_PAD_AUD3_BB_CK__AUD3_TXC,
+	MX51_PAD_AUD3_BB_FS__AUD3_TXFS,
 };
 
 /* Serial ports */

arch/arm/mach-mxs/Kconfig

@@ -7,18 +7,28 @@ config MXS_OCOTP
 
 config SOC_IMX23
 	bool
+	select ARM_AMBA
 	select CPU_ARM926T
 	select HAVE_PWM
 	select PINCTRL_IMX23
 
 config SOC_IMX28
 	bool
+	select ARM_AMBA
 	select CPU_ARM926T
 	select HAVE_PWM
 	select PINCTRL_IMX28
 
 comment "MXS platforms:"
 
+config MACH_MXS_DT
+	bool "Support MXS platforms from device tree"
+	select SOC_IMX23
+	select SOC_IMX28
+	help
+	  Include support for Freescale MXS platforms(i.MX23 and i.MX28)
+	  using the device tree for discovery
+
 config MACH_STMP378X_DEVB
 	bool "Support STMP378x_devb Platform"
 	select SOC_IMX23

arch/arm/mach-mxs/Makefile

@@ -4,6 +4,7 @@ obj-y := devices.o icoll.o iomux.o system.o timer.o mm.o
 obj-$(CONFIG_MXS_OCOTP) += ocotp.o
 obj-$(CONFIG_PM) += pm.o
 
+obj-$(CONFIG_MACH_MXS_DT) += mach-mxs.o
 obj-$(CONFIG_MACH_STMP378X_DEVB) += mach-stmp378x_devb.o
 obj-$(CONFIG_MACH_MX23EVK) += mach-mx23evk.o
 obj-$(CONFIG_MACH_MX28EVK) += mach-mx28evk.o

arch/arm/mach-mxs/devices/Kconfig

 config MXS_HAVE_AMBA_DUART
 	bool
-	select ARM_AMBA
 
 config MXS_HAVE_PLATFORM_AUART
 	bool

arch/arm/mach-mxs/devices/platform-dma.c

@@ -14,7 +14,7 @@
 #include <mach/mx28.h>
 #include <mach/devices-common.h>
 
-static struct platform_device *__init mxs_add_dma(const char *devid,
+struct platform_device *__init mxs_add_dma(const char *devid,
 						resource_size_t base)
 {
 	struct resource res[] = {
@@ -29,22 +29,3 @@ static struct platform_device *__init mxs_add_dma(const char *devid,
 				res, ARRAY_SIZE(res), NULL, 0,
 				DMA_BIT_MASK(32));
 }
-
-static int __init mxs_add_mxs_dma(void)
-{
-	char *apbh = "mxs-dma-apbh";
-	char *apbx = "mxs-dma-apbx";
-
-	if (cpu_is_mx23()) {
-		mxs_add_dma(apbh, MX23_APBH_DMA_BASE_ADDR);
-		mxs_add_dma(apbx, MX23_APBX_DMA_BASE_ADDR);
-	}
-
-	if (cpu_is_mx28()) {
-		mxs_add_dma(apbh, MX28_APBH_DMA_BASE_ADDR);
-		mxs_add_dma(apbx, MX28_APBX_DMA_BASE_ADDR);
-	}
-
-	return 0;
-}
-arch_initcall(mxs_add_mxs_dma);

arch/arm/mach-mxs/devices/platform-gpio-mxs.c

@@ -14,7 +14,7 @@
 #include <mach/devices-common.h>
 
 struct platform_device *__init mxs_add_gpio(
-	int id, resource_size_t iobase, int irq)
+	char *name, int id, resource_size_t iobase, int irq)
 {
 	struct resource res[] = {
 		{
@@ -29,25 +29,5 @@ struct platform_device *__init mxs_add_gpio(
 	};
 
 	return platform_device_register_resndata(&mxs_apbh_bus,
-			"gpio-mxs", id, res, ARRAY_SIZE(res), NULL, 0);
+			name, id, res, ARRAY_SIZE(res), NULL, 0);
 }
-
-static int __init mxs_add_mxs_gpio(void)
-{
-	if (cpu_is_mx23()) {
-		mxs_add_gpio(0, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO0);
-		mxs_add_gpio(1, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO1);
-		mxs_add_gpio(2, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO2);
-	}
-
-	if (cpu_is_mx28()) {
-		mxs_add_gpio(0, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO0);
-		mxs_add_gpio(1, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO1);
-		mxs_add_gpio(2, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO2);
-		mxs_add_gpio(3, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO3);
-		mxs_add_gpio(4, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO4);
-	}
-
-	return 0;
-}
-postcore_initcall(mxs_add_mxs_gpio);

arch/arm/mach-mxs/devices/platform-mxs-mmc.c

@@ -17,8 +17,9 @@
 #include <mach/mx28.h>
 #include <mach/devices-common.h>
 
-#define mxs_mxs_mmc_data_entry_single(soc, _id, hwid)			\
+#define mxs_mxs_mmc_data_entry_single(soc, _devid, _id, hwid)		\
 	{								\
+		.devid = _devid,					\
 		.id = _id,						\
 		.iobase = soc ## _SSP ## hwid ## _BASE_ADDR,		\
 		.dma = soc ## _DMA_SSP ## hwid,				\
@@ -26,23 +27,23 @@
 		.irq_dma = soc ## _INT_SSP ## hwid ## _DMA,		\
 	}
 
-#define mxs_mxs_mmc_data_entry(soc, _id, hwid)				\
-	[_id] = mxs_mxs_mmc_data_entry_single(soc, _id, hwid)
+#define mxs_mxs_mmc_data_entry(soc, _devid, _id, hwid)			\
+	[_id] = mxs_mxs_mmc_data_entry_single(soc, _devid, _id, hwid)
 
 
 #ifdef CONFIG_SOC_IMX23
 const struct mxs_mxs_mmc_data mx23_mxs_mmc_data[] __initconst = {
-	mxs_mxs_mmc_data_entry(MX23, 0, 1),
-	mxs_mxs_mmc_data_entry(MX23, 1, 2),
+	mxs_mxs_mmc_data_entry(MX23, "imx23-mmc", 0, 1),
+	mxs_mxs_mmc_data_entry(MX23, "imx23-mmc", 1, 2),
 };
 #endif
 
 #ifdef CONFIG_SOC_IMX28
 const struct mxs_mxs_mmc_data mx28_mxs_mmc_data[] __initconst = {
-	mxs_mxs_mmc_data_entry(MX28, 0, 0),
-	mxs_mxs_mmc_data_entry(MX28, 1, 1),
-	mxs_mxs_mmc_data_entry(MX28, 2, 2),
-	mxs_mxs_mmc_data_entry(MX28, 3, 3),
+	mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 0, 0),
+	mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 1, 1),
+	mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 2, 2),
+	mxs_mxs_mmc_data_entry(MX28, "imx28-mmc", 3, 3),
 };
 #endif
 
@@ -70,6 +71,6 @@ struct platform_device *__init mxs_add_mxs_mmc(
 		},
 	};
 
-	return mxs_add_platform_device("mxs-mmc", data->id,
+	return mxs_add_platform_device(data->devid, data->id,
 			res, ARRAY_SIZE(res), pdata, sizeof(*pdata));
 }

arch/arm/mach-mxs/include/mach/common.h

@@ -18,17 +18,20 @@ extern void mxs_restart(char, const char *);
 extern int mxs_saif_clkmux_select(unsigned int clkmux);
 
 extern void mx23_soc_init(void);
-extern int mx23_register_gpios(void);
 extern int mx23_clocks_init(void);
 extern void mx23_map_io(void);
 extern void mx23_init_irq(void);
 
 extern void mx28_soc_init(void);
-extern int mx28_register_gpios(void);
 extern int mx28_clocks_init(void);
 extern void mx28_map_io(void);
 extern void mx28_init_irq(void);
 
 extern void icoll_init_irq(void);
 
+extern struct platform_device *mxs_add_dma(const char *devid,
+						resource_size_t base);
+extern struct platform_device *mxs_add_gpio(char *name, int id,
+					    resource_size_t iobase, int irq);
+
 #endif /* __MACH_MXS_COMMON_H__ */

arch/arm/mach-mxs/include/mach/devices-common.h

@@ -82,8 +82,9 @@ struct platform_device * __init mxs_add_mxs_i2c(
 		const struct mxs_mxs_i2c_data *data);
 
 /* mmc */
-#include <mach/mmc.h>
+#include <linux/mmc/mxs-mmc.h>
 struct mxs_mxs_mmc_data {
+	const char *devid;
 	int id;
 	resource_size_t iobase;
 	resource_size_t dma;

arch/arm/mach-mxs/mach-mxs.c

+/*
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ * Copyright 2012 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/init.h>
+#include <linux/irqdomain.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <mach/common.h>
+
+static int __init mxs_icoll_add_irq_domain(struct device_node *np,
+				struct device_node *interrupt_parent)
+{
+	irq_domain_add_legacy(np, 128, 0, 0, &irq_domain_simple_ops, NULL);
+
+	return 0;
+}
+
+static int __init mxs_gpio_add_irq_domain(struct device_node *np,
+				struct device_node *interrupt_parent)
+{
+	static int gpio_irq_base = MXS_GPIO_IRQ_START;
+
+	irq_domain_add_legacy(np, 32, gpio_irq_base, 0, &irq_domain_simple_ops, NULL);
+	gpio_irq_base += 32;
+
+	return 0;
+}
+
+static const struct of_device_id mxs_irq_match[] __initconst = {
+	{ .compatible = "fsl,mxs-icoll", .data = mxs_icoll_add_irq_domain, },
+	{ .compatible = "fsl,mxs-gpio", .data = mxs_gpio_add_irq_domain, },
+	{ /* sentinel */ }
+};
+
+static void __init mxs_dt_init_irq(void)
+{
+	icoll_init_irq();
+	of_irq_init(mxs_irq_match);
+}
+
+static void __init imx23_timer_init(void)
+{
+	mx23_clocks_init();
+}
+
+static struct sys_timer imx23_timer = {
+	.init = imx23_timer_init,
+};
+
+static void __init imx28_timer_init(void)
+{
+	mx28_clocks_init();
+}
+
+static struct sys_timer imx28_timer = {
+	.init = imx28_timer_init,
+};
+
+static void __init imx28_evk_init(void)
+{
+	struct clk *clk;
+
+	/* Enable fec phy clock */
+	clk = clk_get_sys("enet_out", NULL);
+	if (!IS_ERR(clk))
+		clk_prepare_enable(clk);
+}
+
+static void __init mxs_machine_init(void)
+{
+	if (of_machine_is_compatible("fsl,imx28-evk"))
+		imx28_evk_init();
+
+	of_platform_populate(NULL, of_default_bus_match_table,
+				NULL, NULL);
+}
+
+static const char *imx23_dt_compat[] __initdata = {
+	"fsl,imx23-evk",
+	"fsl,imx23",
+	NULL,
+};
+
+static const char *imx28_dt_compat[] __initdata = {
+	"fsl,imx28-evk",
+	"fsl,imx28",
+	NULL,
+};
+
+DT_MACHINE_START(IMX23, "Freescale i.MX23 (Device Tree)")
+	.map_io		= mx23_map_io,
+	.init_irq	= mxs_dt_init_irq,
+	.timer		= &imx23_timer,
+	.init_machine	= mxs_machine_init,
+	.dt_compat	= imx23_dt_compat,
+	.restart	= mxs_restart,
+MACHINE_END
+
+DT_MACHINE_START(IMX28, "Freescale i.MX28 (Device Tree)")
+	.map_io		= mx28_map_io,
+	.init_irq	= mxs_dt_init_irq,
+	.timer		= &imx28_timer,
+	.init_machine	= mxs_machine_init,
+	.dt_compat	= imx28_dt_compat,
+	.restart	= mxs_restart,
+MACHINE_END

arch/arm/mach-mxs/mm.c

@@ -66,9 +66,25 @@ void __init mx28_init_irq(void)
 void __init mx23_soc_init(void)
 {
 	pinctrl_provide_dummies();
+
+	mxs_add_dma("imx23-dma-apbh", MX23_APBH_DMA_BASE_ADDR);
+	mxs_add_dma("imx23-dma-apbx", MX23_APBX_DMA_BASE_ADDR);
+
+	mxs_add_gpio("imx23-gpio", 0, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO0);
+	mxs_add_gpio("imx23-gpio", 1, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO1);
+	mxs_add_gpio("imx23-gpio", 2, MX23_PINCTRL_BASE_ADDR, MX23_INT_GPIO2);
 }
 
 void __init mx28_soc_init(void)
 {
 	pinctrl_provide_dummies();
+
+	mxs_add_dma("imx28-dma-apbh", MX23_APBH_DMA_BASE_ADDR);
+	mxs_add_dma("imx28-dma-apbx", MX23_APBX_DMA_BASE_ADDR);
+
+	mxs_add_gpio("imx28-gpio", 0, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO0);
+	mxs_add_gpio("imx28-gpio", 1, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO1);
+	mxs_add_gpio("imx28-gpio", 2, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO2);
+	mxs_add_gpio("imx28-gpio", 3, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO3);
+	mxs_add_gpio("imx28-gpio", 4, MX28_PINCTRL_BASE_ADDR, MX28_INT_GPIO4);
 }

arch/arm/plat-mxc/include/mach/debug-macro.S

@@ -24,6 +24,8 @@
 #define UART_PADDR	MX51_UART1_BASE_ADDR
 #elif defined (CONFIG_DEBUG_IMX50_IMX53_UART)
 #define UART_PADDR	MX53_UART1_BASE_ADDR
+#elif defined (CONFIG_DEBUG_IMX6Q_UART2)
+#define UART_PADDR	MX6Q_UART2_BASE_ADDR
 #elif defined (CONFIG_DEBUG_IMX6Q_UART4)
 #define UART_PADDR	MX6Q_UART4_BASE_ADDR
 #endif

arch/arm/plat-mxc/include/mach/mx6q.h

@@ -27,6 +27,8 @@
 #define MX6Q_CCM_SIZE			0x4000
 #define MX6Q_ANATOP_BASE_ADDR		0x020c8000
 #define MX6Q_ANATOP_SIZE		0x1000
+#define MX6Q_UART2_BASE_ADDR		0x021e8000
+#define MX6Q_UART2_SIZE			0x4000
 #define MX6Q_UART4_BASE_ADDR		0x021f0000
 #define MX6Q_UART4_SIZE			0x4000
 

drivers/clk/mxs/clk-imx23.c

@@ -81,19 +81,20 @@ static struct clk_lookup uart_lookups[] __initdata = {
 };
 
 static struct clk_lookup hbus_lookups[] __initdata = {
-	{ .dev_id = "mxs-dma-apbh", },
+	{ .dev_id = "imx23-dma-apbh", },
 	{ .dev_id = "80004000.dma-apbh", },
 };
 
 static struct clk_lookup xbus_lookups[] __initdata = {
 	{ .dev_id = "duart", .con_id = "apb_pclk"},
-	{ .dev_id = "mxs-dma-apbx", },
+	{ .dev_id = "80070000.serial", .con_id = "apb_pclk"},
+	{ .dev_id = "imx23-dma-apbx", },
 	{ .dev_id = "80024000.dma-apbx", },
 };
 
 static struct clk_lookup ssp_lookups[] __initdata = {
-	{ .dev_id = "mxs-mmc.0", },
-	{ .dev_id = "mxs-mmc.1", },
+	{ .dev_id = "imx23-mmc.0", },
+	{ .dev_id = "imx23-mmc.1", },
 	{ .dev_id = "80010000.ssp", },
 	{ .dev_id = "80034000.ssp", },
 };

drivers/clk/mxs/clk-imx28.c

@@ -136,33 +136,34 @@ static struct clk_lookup uart_lookups[] __initdata = {
 };
 
 static struct clk_lookup hbus_lookups[] __initdata = {
-	{ .dev_id = "mxs-dma-apbh", },
+	{ .dev_id = "imx28-dma-apbh", },
 	{ .dev_id = "80004000.dma-apbh", },
 };
 
 static struct clk_lookup xbus_lookups[] __initdata = {
 	{ .dev_id = "duart", .con_id = "apb_pclk"},
-	{ .dev_id = "mxs-dma-apbx", },
+	{ .dev_id = "80074000.serial", .con_id = "apb_pclk"},
+	{ .dev_id = "imx28-dma-apbx", },
 	{ .dev_id = "80024000.dma-apbx", },
 };
 
 static struct clk_lookup ssp0_lookups[] __initdata = {
-	{ .dev_id = "mxs-mmc.0", },
+	{ .dev_id = "imx28-mmc.0", },
 	{ .dev_id = "80010000.ssp", },
 };
 
 static struct clk_lookup ssp1_lookups[] __initdata = {
-	{ .dev_id = "mxs-mmc.1", },
+	{ .dev_id = "imx28-mmc.1", },
 	{ .dev_id = "80012000.ssp", },
 };
 
 static struct clk_lookup ssp2_lookups[] __initdata = {
-	{ .dev_id = "mxs-mmc.2", },
+	{ .dev_id = "imx28-mmc.2", },
 	{ .dev_id = "80014000.ssp", },
 };
 
 static struct clk_lookup ssp3_lookups[] __initdata = {
-	{ .dev_id = "mxs-mmc.3", },
+	{ .dev_id = "imx28-mmc.3", },
 	{ .dev_id = "80016000.ssp", },
 };
 

drivers/dma/Kconfig

@@ -238,6 +238,7 @@ config IMX_DMA
 config MXS_DMA
 	bool "MXS DMA support"
 	depends on SOC_IMX23 || SOC_IMX28
+	select STMP_DEVICE
 	select DMA_ENGINE
 	help
 	  Support the MXS DMA engine. This engine including APBH-DMA

drivers/dma/mxs-dma.c

@@ -22,11 +22,14 @@
 #include <linux/platform_device.h>
 #include <linux/dmaengine.h>
 #include <linux/delay.h>
+#include <linux/module.h>
 #include <linux/fsl/mxs-dma.h>
+#include <linux/stmp_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
 
 #include <asm/irq.h>
 #include <mach/mxs.h>
-#include <mach/common.h>
 
 #include "dmaengine.h"
 
@@ -36,12 +39,8 @@
  * dma can program the controller registers of peripheral devices.
  */
 
-#define MXS_DMA_APBH		0
-#define MXS_DMA_APBX		1
-#define dma_is_apbh()		(mxs_dma->dev_id == MXS_DMA_APBH)
-
-#define APBH_VERSION_LATEST	3
-#define apbh_is_old()		(mxs_dma->version < APBH_VERSION_LATEST)
+#define dma_is_apbh(mxs_dma)	((mxs_dma)->type == MXS_DMA_APBH)
+#define apbh_is_old(mxs_dma)	((mxs_dma)->dev_id == IMX23_DMA)
 
 #define HW_APBHX_CTRL0				0x000
 #define BM_APBH_CTRL0_APB_BURST8_EN		(1 << 29)
@@ -51,13 +50,14 @@
 #define HW_APBHX_CTRL2				0x020
 #define HW_APBHX_CHANNEL_CTRL			0x030
 #define BP_APBHX_CHANNEL_CTRL_RESET_CHANNEL	16
-#define HW_APBH_VERSION				(cpu_is_mx23() ? 0x3f0 : 0x800)
-#define HW_APBX_VERSION				0x800
-#define BP_APBHX_VERSION_MAJOR			24
-#define HW_APBHX_CHn_NXTCMDAR(n) \
-	(((dma_is_apbh() && apbh_is_old()) ? 0x050 : 0x110) + (n) * 0x70)
-#define HW_APBHX_CHn_SEMA(n) \
-	(((dma_is_apbh() && apbh_is_old()) ? 0x080 : 0x140) + (n) * 0x70)
+/*
+ * The offset of NXTCMDAR register is different per both dma type and version,
+ * while stride for each channel is all the same 0x70.
+ */
+#define HW_APBHX_CHn_NXTCMDAR(d, n) \
+	(((dma_is_apbh(d) && apbh_is_old(d)) ? 0x050 : 0x110) + (n) * 0x70)
+#define HW_APBHX_CHn_SEMA(d, n) \
+	(((dma_is_apbh(d) && apbh_is_old(d)) ? 0x080 : 0x140) + (n) * 0x70)
 
 /*
  * ccw bits definitions
@@ -121,9 +121,19 @@ struct mxs_dma_chan {
 #define MXS_DMA_CHANNELS		16
 #define MXS_DMA_CHANNELS_MASK		0xffff
 
+enum mxs_dma_devtype {
+	MXS_DMA_APBH,
+	MXS_DMA_APBX,
+};
+
+enum mxs_dma_id {
+	IMX23_DMA,
+	IMX28_DMA,
+};
+
 struct mxs_dma_engine {
-	int				dev_id;
-	unsigned int			version;
+	enum mxs_dma_id			dev_id;
+	enum mxs_dma_devtype		type;
 	void __iomem			*base;
 	struct clk			*clk;
 	struct dma_device		dma_device;
@@ -131,17 +141,86 @@ struct mxs_dma_engine {
 	struct mxs_dma_chan		mxs_chans[MXS_DMA_CHANNELS];
 };
 
+struct mxs_dma_type {
+	enum mxs_dma_id id;
+	enum mxs_dma_devtype type;
+};
+
+static struct mxs_dma_type mxs_dma_types[] = {
+	{
+		.id = IMX23_DMA,
+		.type = MXS_DMA_APBH,
+	}, {
+		.id = IMX23_DMA,
+		.type = MXS_DMA_APBX,
+	}, {
+		.id = IMX28_DMA,
+		.type = MXS_DMA_APBH,
+	}, {
+		.id = IMX28_DMA,
+		.type = MXS_DMA_APBX,
+	}
+};
+
+static struct platform_device_id mxs_dma_ids[] = {
+	{
+		.name = "imx23-dma-apbh",
+		.driver_data = (kernel_ulong_t) &mxs_dma_types[0],
+	}, {
+		.name = "imx23-dma-apbx",
+		.driver_data = (kernel_ulong_t) &mxs_dma_types[1],
+	}, {
+		.name = "imx28-dma-apbh",
+		.driver_data = (kernel_ulong_t) &mxs_dma_types[2],
+	}, {
+		.name = "imx28-dma-apbx",
+		.driver_data = (kernel_ulong_t) &mxs_dma_types[3],
+	}, {
+		/* end of list */
+	}
+};
+
+static const struct of_device_id mxs_dma_dt_ids[] = {
+	{ .compatible = "fsl,imx23-dma-apbh", .data = &mxs_dma_ids[0], },
+	{ .compatible = "fsl,imx23-dma-apbx", .data = &mxs_dma_ids[1], },
+	{ .compatible = "fsl,imx28-dma-apbh", .data = &mxs_dma_ids[2], },
+	{ .compatible = "fsl,imx28-dma-apbx", .data = &mxs_dma_ids[3], },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_dma_dt_ids);
+
+static struct mxs_dma_chan *to_mxs_dma_chan(struct dma_chan *chan)
+{
+	return container_of(chan, struct mxs_dma_chan, chan);
+}
+
+int mxs_dma_is_apbh(struct dma_chan *chan)
+{
+	struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+
+	return dma_is_apbh(mxs_dma);
+}
+
+int mxs_dma_is_apbx(struct dma_chan *chan)
+{
+	struct mxs_dma_chan *mxs_chan = to_mxs_dma_chan(chan);
+	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
+
+	return !dma_is_apbh(mxs_dma);
+}
+
 static void mxs_dma_reset_chan(struct mxs_dma_chan *mxs_chan)
 {
 	struct mxs_dma_engine *mxs_dma = mxs_chan->mxs_dma;
 	int chan_id = mxs_chan->chan.chan_id;
 
-	if (dma_is_apbh() && apbh_is_old())
+	if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
 		writel(1 << (chan_id + BP_APBH_CTRL0_RESET_CHANNEL),
-			mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
 	else
 		writel(1 << (chan_id + BP_APBHX_CHANNEL_CTRL_RESET_CHANNEL),
-			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_SET);
 }
 
 static void mxs_dma_enable_chan(struct mxs_dma_chan *mxs_chan)
@@ -151,10 +230,10 @@ static void mxs_dma_enable_chan(struct mxs_dma_chan *mxs_chan)
 
 	/* set cmd_addr up */
 	writel(mxs_chan->ccw_phys,
-		mxs_dma->base + HW_APBHX_CHn_NXTCMDAR(chan_id));
+		mxs_dma->base + HW_APBHX_CHn_NXTCMDAR(mxs_dma, chan_id));
 
 	/* write 1 to SEMA to kick off the channel */
-	writel(1, mxs_dma->base + HW_APBHX_CHn_SEMA(chan_id));
+	writel(1, mxs_dma->base + HW_APBHX_CHn_SEMA(mxs_dma, chan_id));
 }
 
 static void mxs_dma_disable_chan(struct mxs_dma_chan *mxs_chan)
@@ -168,12 +247,12 @@ static void mxs_dma_pause_chan(struct mxs_dma_chan *mxs_chan)
 	int chan_id = mxs_chan->chan.chan_id;
 
 	/* freeze the channel */
-	if (dma_is_apbh() && apbh_is_old())
+	if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
 		writel(1 << chan_id,
-			mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
 	else
 		writel(1 << chan_id,
-			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_SET);
 
 	mxs_chan->status = DMA_PAUSED;
 }
@@ -184,21 +263,16 @@ static void mxs_dma_resume_chan(struct mxs_dma_chan *mxs_chan)
 	int chan_id = mxs_chan->chan.chan_id;
 
 	/* unfreeze the channel */
-	if (dma_is_apbh() && apbh_is_old())
+	if (dma_is_apbh(mxs_dma) && apbh_is_old(mxs_dma))
 		writel(1 << chan_id,
-			mxs_dma->base + HW_APBHX_CTRL0 + MXS_CLR_ADDR);
+			mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_CLR);
 	else
 		writel(1 << chan_id,
-			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + MXS_CLR_ADDR);
+			mxs_dma->base + HW_APBHX_CHANNEL_CTRL + STMP_OFFSET_REG_CLR);
 
 	mxs_chan->status = DMA_IN_PROGRESS;
 }
 
-static struct mxs_dma_chan *to_mxs_dma_chan(struct dma_chan *chan)
-{
-	return container_of(chan, struct mxs_dma_chan, chan);
-}
-
 static dma_cookie_t mxs_dma_tx_submit(struct dma_async_tx_descriptor *tx)
 {
 	return dma_cookie_assign(tx);
@@ -220,11 +294,11 @@ static irqreturn_t mxs_dma_int_handler(int irq, void *dev_id)
 	/* completion status */
 	stat1 = readl(mxs_dma->base + HW_APBHX_CTRL1);
 	stat1 &= MXS_DMA_CHANNELS_MASK;
-	writel(stat1, mxs_dma->base + HW_APBHX_CTRL1 + MXS_CLR_ADDR);
+	writel(stat1, mxs_dma->base + HW_APBHX_CTRL1 + STMP_OFFSET_REG_CLR);
 
 	/* error status */
 	stat2 = readl(mxs_dma->base + HW_APBHX_CTRL2);
-	writel(stat2, mxs_dma->base + HW_APBHX_CTRL2 + MXS_CLR_ADDR);
+	writel(stat2, mxs_dma->base + HW_APBHX_CTRL2 + STMP_OFFSET_REG_CLR);
 
 	/*
 	 * When both completion and error of termination bits set at the
@@ -567,27 +641,21 @@ static int __init mxs_dma_init(struct mxs_dma_engine *mxs_dma)
 	if (ret)
 		return ret;
 
-	ret = mxs_reset_block(mxs_dma->base);
+	ret = stmp_reset_block(mxs_dma->base);
 	if (ret)
 		goto err_out;
 
-	/* only major version matters */
-	mxs_dma->version = readl(mxs_dma->base +
-				((mxs_dma->dev_id == MXS_DMA_APBX) ?
-				HW_APBX_VERSION : HW_APBH_VERSION)) >>
-				BP_APBHX_VERSION_MAJOR;
-
 	/* enable apbh burst */
-	if (dma_is_apbh()) {
+	if (dma_is_apbh(mxs_dma)) {
 		writel(BM_APBH_CTRL0_APB_BURST_EN,
-			mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
 		writel(BM_APBH_CTRL0_APB_BURST8_EN,
-			mxs_dma->base + HW_APBHX_CTRL0 + MXS_SET_ADDR);
+			mxs_dma->base + HW_APBHX_CTRL0 + STMP_OFFSET_REG_SET);
 	}
 
 	/* enable irq for all the channels */
 	writel(MXS_DMA_CHANNELS_MASK << MXS_DMA_CHANNELS,
-		mxs_dma->base + HW_APBHX_CTRL1 + MXS_SET_ADDR);
+		mxs_dma->base + HW_APBHX_CTRL1 + STMP_OFFSET_REG_SET);
 
 err_out:
 	clk_disable_unprepare(mxs_dma->clk);
@@ -596,8 +664,9 @@ static int __init mxs_dma_init(struct mxs_dma_engine *mxs_dma)
 
 static int __init mxs_dma_probe(struct platform_device *pdev)
 {
-	const struct platform_device_id *id_entry =
-				platform_get_device_id(pdev);
+	const struct platform_device_id *id_entry;
+	const struct of_device_id *of_id;
+	const struct mxs_dma_type *dma_type;
 	struct mxs_dma_engine *mxs_dma;
 	struct resource *iores;
 	int ret, i;
@@ -606,7 +675,15 @@ static int __init mxs_dma_probe(struct platform_device *pdev)
 	if (!mxs_dma)
 		return -ENOMEM;
 
-	mxs_dma->dev_id = id_entry->driver_data;
+	of_id = of_match_device(mxs_dma_dt_ids, &pdev->dev);
+	if (of_id)
+		id_entry = of_id->data;
+	else
+		id_entry = platform_get_device_id(pdev);
+
+	dma_type = (struct mxs_dma_type *)id_entry->driver_data;
+	mxs_dma->type = dma_type->type;
+	mxs_dma->dev_id = dma_type->id;
 
 	iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
 
@@ -689,23 +766,12 @@ static int __init mxs_dma_probe(struct platform_device *pdev)
 	return ret;
 }
 
-static struct platform_device_id mxs_dma_type[] = {
-	{
-		.name = "mxs-dma-apbh",
-		.driver_data = MXS_DMA_APBH,
-	}, {
-		.name = "mxs-dma-apbx",
-		.driver_data = MXS_DMA_APBX,
-	}, {
-		/* end of list */
-	}
-};
-
 static struct platform_driver mxs_dma_driver = {
 	.driver		= {
 		.name	= "mxs-dma",
+		.of_match_table = mxs_dma_dt_ids,
 	},
-	.id_table	= mxs_dma_type,
+	.id_table	= mxs_dma_ids,
 };
 
 static int __init mxs_dma_module_init(void)

drivers/gpio/gpio-mxs.c

@@ -25,23 +25,25 @@
 #include <linux/io.h>
 #include <linux/irq.h>
 #include <linux/gpio.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/slab.h>
 #include <linux/basic_mmio_gpio.h>
 #include <linux/module.h>
-#include <mach/mxs.h>
 
 #define MXS_SET		0x4
 #define MXS_CLR		0x8
 
-#define PINCTRL_DOUT(n)		((cpu_is_mx23() ? 0x0500 : 0x0700) + (n) * 0x10)
-#define PINCTRL_DIN(n)		((cpu_is_mx23() ? 0x0600 : 0x0900) + (n) * 0x10)
-#define PINCTRL_DOE(n)		((cpu_is_mx23() ? 0x0700 : 0x0b00) + (n) * 0x10)
-#define PINCTRL_PIN2IRQ(n)	((cpu_is_mx23() ? 0x0800 : 0x1000) + (n) * 0x10)
-#define PINCTRL_IRQEN(n)	((cpu_is_mx23() ? 0x0900 : 0x1100) + (n) * 0x10)
-#define PINCTRL_IRQLEV(n)	((cpu_is_mx23() ? 0x0a00 : 0x1200) + (n) * 0x10)
-#define PINCTRL_IRQPOL(n)	((cpu_is_mx23() ? 0x0b00 : 0x1300) + (n) * 0x10)
-#define PINCTRL_IRQSTAT(n)	((cpu_is_mx23() ? 0x0c00 : 0x1400) + (n) * 0x10)
+#define PINCTRL_DOUT(p)		((is_imx23_gpio(p) ? 0x0500 : 0x0700) + (p->id) * 0x10)
+#define PINCTRL_DIN(p)		((is_imx23_gpio(p) ? 0x0600 : 0x0900) + (p->id) * 0x10)
+#define PINCTRL_DOE(p)		((is_imx23_gpio(p) ? 0x0700 : 0x0b00) + (p->id) * 0x10)
+#define PINCTRL_PIN2IRQ(p)	((is_imx23_gpio(p) ? 0x0800 : 0x1000) + (p->id) * 0x10)
+#define PINCTRL_IRQEN(p)	((is_imx23_gpio(p) ? 0x0900 : 0x1100) + (p->id) * 0x10)
+#define PINCTRL_IRQLEV(p)	((is_imx23_gpio(p) ? 0x0a00 : 0x1200) + (p->id) * 0x10)
+#define PINCTRL_IRQPOL(p)	((is_imx23_gpio(p) ? 0x0b00 : 0x1300) + (p->id) * 0x10)
+#define PINCTRL_IRQSTAT(p)	((is_imx23_gpio(p) ? 0x0c00 : 0x1400) + (p->id) * 0x10)
 
 #define GPIO_INT_FALL_EDGE	0x0
 #define GPIO_INT_LOW_LEV	0x1
@@ -52,14 +54,30 @@
 
 #define irq_to_gpio(irq)	((irq) - MXS_GPIO_IRQ_START)
 
+enum mxs_gpio_id {
+	IMX23_GPIO,
+	IMX28_GPIO,
+};
+
 struct mxs_gpio_port {
 	void __iomem *base;
 	int id;
 	int irq;
 	int virtual_irq_start;
 	struct bgpio_chip bgc;
+	enum mxs_gpio_id devid;
 };
 
+static inline int is_imx23_gpio(struct mxs_gpio_port *port)
+{
+	return port->devid == IMX23_GPIO;
+}
+
+static inline int is_imx28_gpio(struct mxs_gpio_port *port)
+{
+	return port->devid == IMX28_GPIO;
+}
+
 /* Note: This driver assumes 32 GPIOs are handled in one register */
 
 static int mxs_gpio_set_irq_type(struct irq_data *d, unsigned int type)
@@ -89,21 +107,21 @@ static int mxs_gpio_set_irq_type(struct irq_data *d, unsigned int type)
 	}
 
 	/* set level or edge */
-	pin_addr = port->base + PINCTRL_IRQLEV(port->id);
+	pin_addr = port->base + PINCTRL_IRQLEV(port);
 	if (edge & GPIO_INT_LEV_MASK)
 		writel(pin_mask, pin_addr + MXS_SET);
 	else
 		writel(pin_mask, pin_addr + MXS_CLR);
 
 	/* set polarity */
-	pin_addr = port->base + PINCTRL_IRQPOL(port->id);
+	pin_addr = port->base + PINCTRL_IRQPOL(port);
 	if (edge & GPIO_INT_POL_MASK)
 		writel(pin_mask, pin_addr + MXS_SET);
 	else
 		writel(pin_mask, pin_addr + MXS_CLR);
 
 	writel(1 << (gpio & 0x1f),
-	       port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+	       port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
 
 	return 0;
 }
@@ -117,8 +135,8 @@ static void mxs_gpio_irq_handler(u32 irq, struct irq_desc *desc)
 
 	desc->irq_data.chip->irq_ack(&desc->irq_data);
 
-	irq_stat = readl(port->base + PINCTRL_IRQSTAT(port->id)) &
-			readl(port->base + PINCTRL_IRQEN(port->id));
+	irq_stat = readl(port->base + PINCTRL_IRQSTAT(port)) &
+			readl(port->base + PINCTRL_IRQEN(port));
 
 	while (irq_stat != 0) {
 		int irqoffset = fls(irq_stat) - 1;
@@ -164,8 +182,8 @@ static void __init mxs_gpio_init_gc(struct mxs_gpio_port *port)
 	ct->chip.irq_unmask = irq_gc_mask_set_bit;
 	ct->chip.irq_set_type = mxs_gpio_set_irq_type;
 	ct->chip.irq_set_wake = mxs_gpio_set_wake_irq;
-	ct->regs.ack = PINCTRL_IRQSTAT(port->id) + MXS_CLR;
-	ct->regs.mask = PINCTRL_IRQEN(port->id);
+	ct->regs.ack = PINCTRL_IRQSTAT(port) + MXS_CLR;
+	ct->regs.mask = PINCTRL_IRQEN(port);
 
 	irq_setup_generic_chip(gc, IRQ_MSK(32), 0, IRQ_NOREQUEST, 0);
 }
@@ -179,60 +197,83 @@ static int mxs_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
 	return port->virtual_irq_start + offset;
 }
 
+static struct platform_device_id mxs_gpio_ids[] = {
+	{
+		.name = "imx23-gpio",
+		.driver_data = IMX23_GPIO,
+	}, {
+		.name = "imx28-gpio",
+		.driver_data = IMX28_GPIO,
+	}, {
+		/* sentinel */
+	}
+};
+MODULE_DEVICE_TABLE(platform, mxs_gpio_ids);
+
+static const struct of_device_id mxs_gpio_dt_ids[] = {
+	{ .compatible = "fsl,imx23-gpio", .data = (void *) IMX23_GPIO, },
+	{ .compatible = "fsl,imx28-gpio", .data = (void *) IMX28_GPIO, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_gpio_dt_ids);
+
 static int __devinit mxs_gpio_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *of_id =
+			of_match_device(mxs_gpio_dt_ids, &pdev->dev);
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *parent;
 	static void __iomem *base;
 	struct mxs_gpio_port *port;
 	struct resource *iores = NULL;
 	int err;
 
-	port = kzalloc(sizeof(struct mxs_gpio_port), GFP_KERNEL);
+	port = devm_kzalloc(&pdev->dev, sizeof(*port), GFP_KERNEL);
 	if (!port)
 		return -ENOMEM;
 
+	if (np) {
+		port->id = of_alias_get_id(np, "gpio");
+		if (port->id < 0)
+			return port->id;
+		port->devid = (enum mxs_gpio_id) of_id->data;
+	} else {
 		port->id = pdev->id;
+		port->devid = pdev->id_entry->driver_data;
+	}
 	port->virtual_irq_start = MXS_GPIO_IRQ_START + port->id * 32;
 
+	port->irq = platform_get_irq(pdev, 0);
+	if (port->irq < 0)
+		return port->irq;
+
 	/*
 	 * map memory region only once, as all the gpio ports
 	 * share the same one
 	 */
 	if (!base) {
+		if (np) {
+			parent = of_get_parent(np);
+			base = of_iomap(parent, 0);
+			of_node_put(parent);
+		} else {
 			iores = platform_get_resource(pdev, IORESOURCE_MEM, 0);
-		if (!iores) {
-			err = -ENODEV;
-			goto out_kfree;
-		}
-
-		if (!request_mem_region(iores->start, resource_size(iores),
-					pdev->name)) {
-			err = -EBUSY;
-			goto out_kfree;
-		}
-
-		base = ioremap(iores->start, resource_size(iores));
-		if (!base) {
-			err = -ENOMEM;
-			goto out_release_mem;
+			base = devm_request_and_ioremap(&pdev->dev, iores);
 		}
+		if (!base)
+			return -EADDRNOTAVAIL;
 	}
 	port->base = base;
 
-	port->irq = platform_get_irq(pdev, 0);
-	if (port->irq < 0) {
-		err = -EINVAL;
-		goto out_iounmap;
-	}
-
 	/*
 	 * select the pin interrupt functionality but initially
 	 * disable the interrupts
 	 */
-	writel(~0U, port->base + PINCTRL_PIN2IRQ(port->id));
-	writel(0, port->base + PINCTRL_IRQEN(port->id));
+	writel(~0U, port->base + PINCTRL_PIN2IRQ(port));
+	writel(0, port->base + PINCTRL_IRQEN(port));
 
 	/* clear address has to be used to clear IRQSTAT bits */
-	writel(~0U, port->base + PINCTRL_IRQSTAT(port->id) + MXS_CLR);
+	writel(~0U, port->base + PINCTRL_IRQSTAT(port) + MXS_CLR);
 
 	/* gpio-mxs can be a generic irq chip */
 	mxs_gpio_init_gc(port);
@@ -242,41 +283,32 @@ static int __devinit mxs_gpio_probe(struct platform_device *pdev)
 	irq_set_handler_data(port->irq, port);
 
 	err = bgpio_init(&port->bgc, &pdev->dev, 4,
-			 port->base + PINCTRL_DIN(port->id),
-			 port->base + PINCTRL_DOUT(port->id), NULL,
-			 port->base + PINCTRL_DOE(port->id), NULL, 0);
+			 port->base + PINCTRL_DIN(port),
+			 port->base + PINCTRL_DOUT(port), NULL,
+			 port->base + PINCTRL_DOE(port), NULL, 0);
 	if (err)
-		goto out_iounmap;
+		return err;
 
 	port->bgc.gc.to_irq = mxs_gpio_to_irq;
 	port->bgc.gc.base = port->id * 32;
 
 	err = gpiochip_add(&port->bgc.gc);
-	if (err)
-		goto out_bgpio_remove;
-
-	return 0;
-
-out_bgpio_remove:
+	if (err) {
 		bgpio_remove(&port->bgc);
-out_iounmap:
-	if (iores)
-		iounmap(port->base);
-out_release_mem:
-	if (iores)
-		release_mem_region(iores->start, resource_size(iores));
-out_kfree:
-	kfree(port);
-	dev_info(&pdev->dev, "%s failed with errno %d\n", __func__, err);
 		return err;
+	}
+
+	return 0;
 }
 
 static struct platform_driver mxs_gpio_driver = {
 	.driver		= {
 		.name	= "gpio-mxs",
 		.owner	= THIS_MODULE,
+		.of_match_table = mxs_gpio_dt_ids,
 	},
 	.probe		= mxs_gpio_probe,
+	.id_table	= mxs_gpio_ids,
 };
 
 static int __init mxs_gpio_init(void)

drivers/i2c/busses/i2c-mxs.c

@@ -28,6 +28,9 @@
 #include <linux/io.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/stmp_device.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_i2c.h>
 
 #define DRIVER_NAME "mxs-i2c"
 
@@ -366,6 +369,7 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 	adap->algo = &mxs_i2c_algo;
 	adap->dev.parent = dev;
 	adap->nr = pdev->id;
+	adap->dev.of_node = pdev->dev.of_node;
 	i2c_set_adapdata(adap, i2c);
 	err = i2c_add_numbered_adapter(adap);
 	if (err) {
@@ -375,6 +379,8 @@ static int __devinit mxs_i2c_probe(struct platform_device *pdev)
 		return err;
 	}
 
+	of_i2c_register_devices(adap);
+
 	return 0;
 }
 
@@ -394,10 +400,17 @@ static int __devexit mxs_i2c_remove(struct platform_device *pdev)
 	return 0;
 }
 
+static const struct of_device_id mxs_i2c_dt_ids[] = {
+	{ .compatible = "fsl,imx28-i2c", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_i2c_dt_ids);
+
 static struct platform_driver mxs_i2c_driver = {
 	.driver = {
 		   .name = DRIVER_NAME,
 		   .owner = THIS_MODULE,
+		   .of_match_table = mxs_i2c_dt_ids,
 		   },
 	.remove = __devexit_p(mxs_i2c_remove),
 };

drivers/mmc/host/mxs-mmc.c

@@ -23,6 +23,9 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/ioport.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/of_gpio.h>
 #include <linux/platform_device.h>
 #include <linux/delay.h>
 #include <linux/interrupt.h>
@@ -40,18 +43,15 @@
 #include <linux/module.h>
 #include <linux/fsl/mxs-dma.h>
 #include <linux/pinctrl/consumer.h>
-
-#include <mach/mxs.h>
-#include <mach/common.h>
-#include <mach/mmc.h>
+#include <linux/stmp_device.h>
+#include <linux/mmc/mxs-mmc.h>
 
 #define DRIVER_NAME	"mxs-mmc"
 
 /* card detect polling timeout */
 #define MXS_MMC_DETECT_TIMEOUT			(HZ/2)
 
-#define SSP_VERSION_LATEST	4
-#define ssp_is_old()		(host->version < SSP_VERSION_LATEST)
+#define ssp_is_old(host)	((host)->devid == IMX23_MMC)
 
 /* SSP registers */
 #define HW_SSP_CTRL0				0x000
@@ -86,14 +86,14 @@
 #define  BM_SSP_BLOCK_SIZE_BLOCK_COUNT		(0xffffff << 4)
 #define  BP_SSP_BLOCK_SIZE_BLOCK_SIZE		(0)
 #define  BM_SSP_BLOCK_SIZE_BLOCK_SIZE		(0xf)
-#define HW_SSP_TIMING				(ssp_is_old() ? 0x050 : 0x070)
+#define HW_SSP_TIMING(h)			(ssp_is_old(h) ? 0x050 : 0x070)
 #define  BP_SSP_TIMING_TIMEOUT			(16)
 #define  BM_SSP_TIMING_TIMEOUT			(0xffff << 16)
 #define  BP_SSP_TIMING_CLOCK_DIVIDE		(8)
 #define  BM_SSP_TIMING_CLOCK_DIVIDE		(0xff << 8)
 #define  BP_SSP_TIMING_CLOCK_RATE		(0)
 #define  BM_SSP_TIMING_CLOCK_RATE		(0xff)
-#define HW_SSP_CTRL1				(ssp_is_old() ? 0x060 : 0x080)
+#define HW_SSP_CTRL1(h)				(ssp_is_old(h) ? 0x060 : 0x080)
 #define  BM_SSP_CTRL1_SDIO_IRQ			(1 << 31)
 #define  BM_SSP_CTRL1_SDIO_IRQ_EN		(1 << 30)
 #define  BM_SSP_CTRL1_RESP_ERR_IRQ		(1 << 29)
@@ -116,15 +116,13 @@
 #define  BM_SSP_CTRL1_WORD_LENGTH		(0xf << 4)
 #define  BP_SSP_CTRL1_SSP_MODE			(0)
 #define  BM_SSP_CTRL1_SSP_MODE			(0xf)
-#define HW_SSP_SDRESP0				(ssp_is_old() ? 0x080 : 0x0a0)
-#define HW_SSP_SDRESP1				(ssp_is_old() ? 0x090 : 0x0b0)
-#define HW_SSP_SDRESP2				(ssp_is_old() ? 0x0a0 : 0x0c0)
-#define HW_SSP_SDRESP3				(ssp_is_old() ? 0x0b0 : 0x0d0)
-#define HW_SSP_STATUS				(ssp_is_old() ? 0x0c0 : 0x100)
+#define HW_SSP_SDRESP0(h)			(ssp_is_old(h) ? 0x080 : 0x0a0)
+#define HW_SSP_SDRESP1(h)			(ssp_is_old(h) ? 0x090 : 0x0b0)
+#define HW_SSP_SDRESP2(h)			(ssp_is_old(h) ? 0x0a0 : 0x0c0)
+#define HW_SSP_SDRESP3(h)			(ssp_is_old(h) ? 0x0b0 : 0x0d0)
+#define HW_SSP_STATUS(h)			(ssp_is_old(h) ? 0x0c0 : 0x100)
 #define  BM_SSP_STATUS_CARD_DETECT		(1 << 28)
 #define  BM_SSP_STATUS_SDIO_IRQ			(1 << 17)
-#define HW_SSP_VERSION				(cpu_is_mx23() ? 0x110 : 0x130)
-#define  BP_SSP_VERSION_MAJOR			(24)
 
 #define BF_SSP(value, field)	(((value) << BP_SSP_##field) & BM_SSP_##field)
 
@@ -139,6 +137,11 @@
 
 #define SSP_PIO_NUM	3
 
+enum mxs_mmc_id {
+	IMX23_MMC,
+	IMX28_MMC,
+};
+
 struct mxs_mmc_host {
 	struct mmc_host			*mmc;
 	struct mmc_request		*mrq;
@@ -146,9 +149,7 @@ struct mxs_mmc_host {
 	struct mmc_data			*data;
 
 	void __iomem			*base;
-	int				irq;
-	struct resource			*res;
-	struct resource			*dma_res;
+	int				dma_channel;
 	struct clk			*clk;
 	unsigned int			clk_rate;
 
@@ -158,32 +159,28 @@ struct mxs_mmc_host {
 	enum dma_transfer_direction	slave_dirn;
 	u32				ssp_pio_words[SSP_PIO_NUM];
 
-	unsigned int			version;
+	enum mxs_mmc_id			devid;
 	unsigned char			bus_width;
 	spinlock_t			lock;
 	int				sdio_irq_en;
+	int				wp_gpio;
 };
 
 static int mxs_mmc_get_ro(struct mmc_host *mmc)
 {
 	struct mxs_mmc_host *host = mmc_priv(mmc);
-	struct mxs_mmc_platform_data *pdata =
-		mmc_dev(host->mmc)->platform_data;
-
-	if (!pdata)
-		return -EFAULT;
 
-	if (!gpio_is_valid(pdata->wp_gpio))
+	if (!gpio_is_valid(host->wp_gpio))
 		return -EINVAL;
 
-	return gpio_get_value(pdata->wp_gpio);
+	return gpio_get_value(host->wp_gpio);
 }
 
 static int mxs_mmc_get_cd(struct mmc_host *mmc)
 {
 	struct mxs_mmc_host *host = mmc_priv(mmc);
 
-	return !(readl(host->base + HW_SSP_STATUS) &
+	return !(readl(host->base + HW_SSP_STATUS(host)) &
 		 BM_SSP_STATUS_CARD_DETECT);
 }
 
@@ -191,7 +188,7 @@ static void mxs_mmc_reset(struct mxs_mmc_host *host)
 {
 	u32 ctrl0, ctrl1;
 
-	mxs_reset_block(host->base);
+	stmp_reset_block(host->base);
 
 	ctrl0 = BM_SSP_CTRL0_IGNORE_CRC;
 	ctrl1 = BF_SSP(0x3, CTRL1_SSP_MODE) |
@@ -207,7 +204,7 @@ static void mxs_mmc_reset(struct mxs_mmc_host *host)
 	writel(BF_SSP(0xffff, TIMING_TIMEOUT) |
 	       BF_SSP(2, TIMING_CLOCK_DIVIDE) |
 	       BF_SSP(0, TIMING_CLOCK_RATE),
-	       host->base + HW_SSP_TIMING);
+	       host->base + HW_SSP_TIMING(host));
 
 	if (host->sdio_irq_en) {
 		ctrl0 |= BM_SSP_CTRL0_SDIO_IRQ_CHECK;
@@ -215,7 +212,7 @@ static void mxs_mmc_reset(struct mxs_mmc_host *host)
 	}
 
 	writel(ctrl0, host->base + HW_SSP_CTRL0);
-	writel(ctrl1, host->base + HW_SSP_CTRL1);
+	writel(ctrl1, host->base + HW_SSP_CTRL1(host));
 }
 
 static void mxs_mmc_start_cmd(struct mxs_mmc_host *host,
@@ -229,12 +226,12 @@ static void mxs_mmc_request_done(struct mxs_mmc_host *host)
 
 	if (mmc_resp_type(cmd) & MMC_RSP_PRESENT) {
 		if (mmc_resp_type(cmd) & MMC_RSP_136) {
-			cmd->resp[3] = readl(host->base + HW_SSP_SDRESP0);
-			cmd->resp[2] = readl(host->base + HW_SSP_SDRESP1);
-			cmd->resp[1] = readl(host->base + HW_SSP_SDRESP2);
-			cmd->resp[0] = readl(host->base + HW_SSP_SDRESP3);
+			cmd->resp[3] = readl(host->base + HW_SSP_SDRESP0(host));
+			cmd->resp[2] = readl(host->base + HW_SSP_SDRESP1(host));
+			cmd->resp[1] = readl(host->base + HW_SSP_SDRESP2(host));
+			cmd->resp[0] = readl(host->base + HW_SSP_SDRESP3(host));
 		} else {
-			cmd->resp[0] = readl(host->base + HW_SSP_SDRESP0);
+			cmd->resp[0] = readl(host->base + HW_SSP_SDRESP0(host));
 		}
 	}
 
@@ -277,9 +274,9 @@ static irqreturn_t mxs_mmc_irq_handler(int irq, void *dev_id)
 
 	spin_lock(&host->lock);
 
-	stat = readl(host->base + HW_SSP_CTRL1);
+	stat = readl(host->base + HW_SSP_CTRL1(host));
 	writel(stat & MXS_MMC_IRQ_BITS,
-	       host->base + HW_SSP_CTRL1 + MXS_CLR_ADDR);
+	       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
 
 	if ((stat & BM_SSP_CTRL1_SDIO_IRQ) && (stat & BM_SSP_CTRL1_SDIO_IRQ_EN))
 		mmc_signal_sdio_irq(host->mmc);
@@ -485,7 +482,7 @@ static void mxs_mmc_adtc(struct mxs_mmc_host *host)
 		blocks = 1;
 
 	/* xfer count, block size and count need to be set differently */
-	if (ssp_is_old()) {
+	if (ssp_is_old(host)) {
 		ctrl0 |= BF_SSP(data_size, CTRL0_XFER_COUNT);
 		cmd0 |= BF_SSP(log2_blksz, CMD0_BLOCK_SIZE) |
 			BF_SSP(blocks - 1, CMD0_BLOCK_COUNT);
@@ -509,10 +506,10 @@ static void mxs_mmc_adtc(struct mxs_mmc_host *host)
 
 	/* set the timeout count */
 	timeout = mxs_ns_to_ssp_ticks(host->clk_rate, data->timeout_ns);
-	val = readl(host->base + HW_SSP_TIMING);
+	val = readl(host->base + HW_SSP_TIMING(host));
 	val &= ~(BM_SSP_TIMING_TIMEOUT);
 	val |= BF_SSP(timeout, TIMING_TIMEOUT);
-	writel(val, host->base + HW_SSP_TIMING);
+	writel(val, host->base + HW_SSP_TIMING(host));
 
 	/* pio */
 	host->ssp_pio_words[0] = ctrl0;
@@ -598,11 +595,11 @@ static void mxs_mmc_set_clk_rate(struct mxs_mmc_host *host, unsigned int rate)
 
 	ssp_sck = ssp_clk / clock_divide / (1 + clock_rate);
 
-	val = readl(host->base + HW_SSP_TIMING);
+	val = readl(host->base + HW_SSP_TIMING(host));
 	val &= ~(BM_SSP_TIMING_CLOCK_DIVIDE | BM_SSP_TIMING_CLOCK_RATE);
 	val |= BF_SSP(clock_divide, TIMING_CLOCK_DIVIDE);
 	val |= BF_SSP(clock_rate, TIMING_CLOCK_RATE);
-	writel(val, host->base + HW_SSP_TIMING);
+	writel(val, host->base + HW_SSP_TIMING(host));
 
 	host->clk_rate = ssp_sck;
 
@@ -637,18 +634,19 @@ static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
 
 	if (enable) {
 		writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
-		       host->base + HW_SSP_CTRL0 + MXS_SET_ADDR);
+		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_SET);
 		writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
-		       host->base + HW_SSP_CTRL1 + MXS_SET_ADDR);
+		       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_SET);
 
-		if (readl(host->base + HW_SSP_STATUS) & BM_SSP_STATUS_SDIO_IRQ)
+		if (readl(host->base + HW_SSP_STATUS(host)) &
+				BM_SSP_STATUS_SDIO_IRQ)
 			mmc_signal_sdio_irq(host->mmc);
 
 	} else {
 		writel(BM_SSP_CTRL0_SDIO_IRQ_CHECK,
-		       host->base + HW_SSP_CTRL0 + MXS_CLR_ADDR);
+		       host->base + HW_SSP_CTRL0 + STMP_OFFSET_REG_CLR);
 		writel(BM_SSP_CTRL1_SDIO_IRQ_EN,
-		       host->base + HW_SSP_CTRL1 + MXS_CLR_ADDR);
+		       host->base + HW_SSP_CTRL1(host) + STMP_OFFSET_REG_CLR);
 	}
 
 	spin_unlock_irqrestore(&host->lock, flags);
@@ -669,7 +667,7 @@ static bool mxs_mmc_dma_filter(struct dma_chan *chan, void *param)
 	if (!mxs_dma_is_apbh(chan))
 		return false;
 
-	if (chan->chan_id != host->dma_res->start)
+	if (chan->chan_id != host->dma_channel)
 		return false;
 
 	chan->private = &host->dma_data;
@@ -677,11 +675,34 @@ static bool mxs_mmc_dma_filter(struct dma_chan *chan, void *param)
 	return true;
 }
 
+static struct platform_device_id mxs_mmc_ids[] = {
+	{
+		.name = "imx23-mmc",
+		.driver_data = IMX23_MMC,
+	}, {
+		.name = "imx28-mmc",
+		.driver_data = IMX28_MMC,
+	}, {
+		/* sentinel */
+	}
+};
+MODULE_DEVICE_TABLE(platform, mxs_mmc_ids);
+
+static const struct of_device_id mxs_mmc_dt_ids[] = {
+	{ .compatible = "fsl,imx23-mmc", .data = (void *) IMX23_MMC, },
+	{ .compatible = "fsl,imx28-mmc", .data = (void *) IMX28_MMC, },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, mxs_mmc_dt_ids);
+
 static int mxs_mmc_probe(struct platform_device *pdev)
 {
+	const struct of_device_id *of_id =
+			of_match_device(mxs_mmc_dt_ids, &pdev->dev);
+	struct device_node *np = pdev->dev.of_node;
 	struct mxs_mmc_host *host;
 	struct mmc_host *mmc;
-	struct resource *iores, *dmares, *r;
+	struct resource *iores, *dmares;
 	struct mxs_mmc_platform_data *pdata;
 	struct pinctrl *pinctrl;
 	int ret = 0, irq_err, irq_dma;
@@ -691,46 +712,51 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 	dmares = platform_get_resource(pdev, IORESOURCE_DMA, 0);
 	irq_err = platform_get_irq(pdev, 0);
 	irq_dma = platform_get_irq(pdev, 1);
-	if (!iores || !dmares || irq_err < 0 || irq_dma < 0)
+	if (!iores || irq_err < 0 || irq_dma < 0)
 		return -EINVAL;
 
-	r = request_mem_region(iores->start, resource_size(iores), pdev->name);
-	if (!r)
-		return -EBUSY;
-
 	mmc = mmc_alloc_host(sizeof(struct mxs_mmc_host), &pdev->dev);
-	if (!mmc) {
-		ret = -ENOMEM;
-		goto out_release_mem;
-	}
+	if (!mmc)
+		return -ENOMEM;
 
 	host = mmc_priv(mmc);
-	host->base = ioremap(r->start, resource_size(r));
+	host->base = devm_request_and_ioremap(&pdev->dev, iores);
 	if (!host->base) {
-		ret = -ENOMEM;
+		ret = -EADDRNOTAVAIL;
 		goto out_mmc_free;
 	}
 
-	/* only major verion does matter */
-	host->version = readl(host->base + HW_SSP_VERSION) >>
-			BP_SSP_VERSION_MAJOR;
+	if (np) {
+		host->devid = (enum mxs_mmc_id) of_id->data;
+		/*
+		 * TODO: This is a temporary solution and should be changed
+		 * to use generic DMA binding later when the helpers get in.
+		 */
+		ret = of_property_read_u32(np, "fsl,ssp-dma-channel",
+					   &host->dma_channel);
+		if (ret) {
+			dev_err(mmc_dev(host->mmc),
+				"failed to get dma channel\n");
+			goto out_mmc_free;
+		}
+	} else {
+		host->devid = pdev->id_entry->driver_data;
+		host->dma_channel = dmares->start;
+	}
 
 	host->mmc = mmc;
-	host->res = r;
-	host->dma_res = dmares;
-	host->irq = irq_err;
 	host->sdio_irq_en = 0;
 
 	pinctrl = devm_pinctrl_get_select_default(&pdev->dev);
 	if (IS_ERR(pinctrl)) {
 		ret = PTR_ERR(pinctrl);
-		goto out_iounmap;
+		goto out_mmc_free;
 	}
 
 	host->clk = clk_get(&pdev->dev, NULL);
 	if (IS_ERR(host->clk)) {
 		ret = PTR_ERR(host->clk);
-		goto out_iounmap;
+		goto out_mmc_free;
 	}
 	clk_prepare_enable(host->clk);
 
@@ -752,11 +778,20 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 		    MMC_CAP_SDIO_IRQ | MMC_CAP_NEEDS_POLL;
 
 	pdata =	mmc_dev(host->mmc)->platform_data;
-	if (pdata) {
+	if (!pdata) {
+		u32 bus_width = 0;
+		of_property_read_u32(np, "bus-width", &bus_width);
+		if (bus_width == 4)
+			mmc->caps |= MMC_CAP_4_BIT_DATA;
+		else if (bus_width == 8)
+			mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
+		host->wp_gpio = of_get_named_gpio(np, "wp-gpios", 0);
+	} else {
 		if (pdata->flags & SLOTF_8_BIT_CAPABLE)
 			mmc->caps |= MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA;
 		if (pdata->flags & SLOTF_4_BIT_CAPABLE)
 			mmc->caps |= MMC_CAP_4_BIT_DATA;
+		host->wp_gpio = pdata->wp_gpio;
 	}
 
 	mmc->f_min = 400000;
@@ -765,13 +800,14 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 
 	mmc->max_segs = 52;
 	mmc->max_blk_size = 1 << 0xf;
-	mmc->max_blk_count = (ssp_is_old()) ? 0xff : 0xffffff;
-	mmc->max_req_size = (ssp_is_old()) ? 0xffff : 0xffffffff;
+	mmc->max_blk_count = (ssp_is_old(host)) ? 0xff : 0xffffff;
+	mmc->max_req_size = (ssp_is_old(host)) ? 0xffff : 0xffffffff;
 	mmc->max_seg_size = dma_get_max_seg_size(host->dmach->device->dev);
 
 	platform_set_drvdata(pdev, mmc);
 
-	ret = request_irq(host->irq, mxs_mmc_irq_handler, 0, DRIVER_NAME, host);
+	ret = devm_request_irq(&pdev->dev, irq_err, mxs_mmc_irq_handler, 0,
+			       DRIVER_NAME, host);
 	if (ret)
 		goto out_free_dma;
 
@@ -779,26 +815,20 @@ static int mxs_mmc_probe(struct platform_device *pdev)
 
 	ret = mmc_add_host(mmc);
 	if (ret)
-		goto out_free_irq;
+		goto out_free_dma;
 
 	dev_info(mmc_dev(host->mmc), "initialized\n");
 
 	return 0;
 
-out_free_irq:
-	free_irq(host->irq, host);
 out_free_dma:
 	if (host->dmach)
 		dma_release_channel(host->dmach);
 out_clk_put:
 	clk_disable_unprepare(host->clk);
 	clk_put(host->clk);
-out_iounmap:
-	iounmap(host->base);
 out_mmc_free:
 	mmc_free_host(mmc);
-out_release_mem:
-	release_mem_region(iores->start, resource_size(iores));
 	return ret;
 }
 
@@ -806,12 +836,9 @@ static int mxs_mmc_remove(struct platform_device *pdev)
 {
 	struct mmc_host *mmc = platform_get_drvdata(pdev);
 	struct mxs_mmc_host *host = mmc_priv(mmc);
-	struct resource *res = host->res;
 
 	mmc_remove_host(mmc);
 
-	free_irq(host->irq, host);
-
 	platform_set_drvdata(pdev, NULL);
 
 	if (host->dmach)
@@ -820,12 +847,8 @@ static int mxs_mmc_remove(struct platform_device *pdev)
 	clk_disable_unprepare(host->clk);
 	clk_put(host->clk);
 
-	iounmap(host->base);
-
 	mmc_free_host(mmc);
 
-	release_mem_region(res->start, resource_size(res));
-
 	return 0;
 }
 
@@ -865,11 +888,13 @@ static const struct dev_pm_ops mxs_mmc_pm_ops = {
 static struct platform_driver mxs_mmc_driver = {
 	.probe		= mxs_mmc_probe,
 	.remove		= mxs_mmc_remove,
+	.id_table	= mxs_mmc_ids,
 	.driver		= {
 		.name	= DRIVER_NAME,
 		.owner	= THIS_MODULE,
 #ifdef CONFIG_PM
 		.pm	= &mxs_mmc_pm_ops,
+		.of_match_table = mxs_mmc_dt_ids,
 #endif
 	},
 };

include/linux/fsl/mxs-dma.h

@@ -15,14 +15,6 @@ struct mxs_dma_data {
 	int chan_irq;
 };
 
-static inline int mxs_dma_is_apbh(struct dma_chan *chan)
-{
-	return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbh");
-}
-
-static inline int mxs_dma_is_apbx(struct dma_chan *chan)
-{
-	return !strcmp(dev_name(chan->device->dev), "mxs-dma-apbx");
-}
-
+extern int mxs_dma_is_apbh(struct dma_chan *chan);
+extern int mxs_dma_is_apbx(struct dma_chan *chan);
 #endif /* __MACH_MXS_DMA_H__ */

arch/arm/mach-mxs/include/mach/mmc.h → include/linux/mmc/mxs-mmc.h

@@ -6,8 +6,8 @@
  * published by the Free Software Foundation.
  */
 
-#ifndef __MACH_MXS_MMC_H__
-#define __MACH_MXS_MMC_H__
+#ifndef __LINUX_MMC_MXS_MMC_H__
+#define __LINUX_MMC_MXS_MMC_H__
 
 struct mxs_mmc_platform_data {
 	int wp_gpio;	/* write protect pin */
@@ -15,4 +15,5 @@ struct mxs_mmc_platform_data {
 #define SLOTF_4_BIT_CAPABLE	(1 << 0)
 #define SLOTF_8_BIT_CAPABLE	(1 << 1)
 };
-#endif /* __MACH_MXS_MMC_H__ */
+
+#endif /* __LINUX_MMC_MXS_MMC_H__ */