Commit 84ad1bab authored by Roger Quadros's avatar Roger Quadros Committed by Tony Lindgren

ARM: dts: am57xx-beagle-x15: use palmas-usb for USB2

The VBUS line of USB2 is connected to VBUS detect logic on
the PMIC. Use the palmas-usb driver to report VBUS events
to the USB driver.

As the palmas-usb driver supports GPIO based ID reporting
provide the GPIO for ID pin as well.
Signed-off-by: default avatarRoger Quadros <rogerq@ti.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent f4746176
...@@ -98,13 +98,6 @@ extcon_usb1: extcon_usb1 { ...@@ -98,13 +98,6 @@ extcon_usb1: extcon_usb1 {
pinctrl-0 = <&extcon_usb1_pins>; pinctrl-0 = <&extcon_usb1_pins>;
}; };
extcon_usb2: extcon_usb2 {
compatible = "linux,extcon-usb-gpio";
id-gpio = <&gpio7 24 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&extcon_usb2_pins>;
};
hdmi0: connector { hdmi0: connector {
compatible = "hdmi-connector"; compatible = "hdmi-connector";
label = "hdmi"; label = "hdmi";
...@@ -326,12 +319,6 @@ extcon_usb1_pins: extcon_usb1_pins { ...@@ -326,12 +319,6 @@ extcon_usb1_pins: extcon_usb1_pins {
>; >;
}; };
extcon_usb2_pins: extcon_usb2_pins {
pinctrl-single,pins = <
0x3e8 (PIN_INPUT_PULLUP | MUX_MODE14) /* uart1_ctsn.gpio7_24 */
>;
};
tpd12s015_pins: pinmux_tpd12s015_pins { tpd12s015_pins: pinmux_tpd12s015_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */ 0x3b0 (PIN_OUTPUT | MUX_MODE14) /* gpio7_10 CT_CP_HPD */
...@@ -504,6 +491,14 @@ tps659038_gpio: tps659038_gpio { ...@@ -504,6 +491,14 @@ tps659038_gpio: tps659038_gpio {
gpio-controller; gpio-controller;
#gpio-cells = <2>; #gpio-cells = <2>;
}; };
extcon_usb2: tps659038_usb {
compatible = "ti,palmas-usb-vid";
ti,enable-vbus-detection;
ti,enable-id-detection;
id-gpios = <&gpio7 24 GPIO_ACTIVE_HIGH>;
};
}; };
tmp102: tmp102@48 { tmp102: tmp102@48 {
...@@ -632,6 +627,14 @@ &omap_dwc3_2 { ...@@ -632,6 +627,14 @@ &omap_dwc3_2 {
}; };
&usb2 { &usb2 {
/*
* Stand alone usage is peripheral only.
* However, with some resistor modifications
* this port can be used via expansion connectors
* as "host" or "dual-role". If so, provide
* the necessary dr_mode override in the expansion
* board's DT.
*/
dr_mode = "peripheral"; dr_mode = "peripheral";
}; };
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment