crypto: mv_cesa - Add support for Orion5X crypto engine

This adds support for Marvell's Cryptographic Engines and Security
Accelerator (CESA) which can be found on a few SoC.
Tested with dm-crypt.
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

drivers/crypto/Kconfig

@@ -157,6 +157,19 @@ config S390_PRNG
 	  ANSI X9.17 standard. The PRNG is usable via the char device
 	  /dev/prandom.
 
+config CRYPTO_DEV_MV_CESA
+	tristate "Marvell's Cryptographic Engine"
+	depends on PLAT_ORION
+	select CRYPTO_ALGAPI
+	select CRYPTO_AES
+	select CRYPTO_BLKCIPHER2
+	help
+	  This driver allows you to utilize the Cryptographic Engines and
+	  Security Accelerator (CESA) which can be found on the Marvell Orion
+	  and Kirkwood SoCs, such as QNAP's TS-209.
+
+	  Currently the driver supports AES in ECB and CBC mode without DMA.
+
 config CRYPTO_DEV_HIFN_795X
 	tristate "Driver HIFN 795x crypto accelerator chips"
 	select CRYPTO_DES

drivers/crypto/Makefile

@@ -2,6 +2,7 @@ obj-$(CONFIG_CRYPTO_DEV_PADLOCK_AES) += padlock-aes.o
 obj-$(CONFIG_CRYPTO_DEV_PADLOCK_SHA) += padlock-sha.o
 obj-$(CONFIG_CRYPTO_DEV_GEODE) += geode-aes.o
 obj-$(CONFIG_CRYPTO_DEV_HIFN_795X) += hifn_795x.o
+obj-$(CONFIG_CRYPTO_DEV_MV_CESA) += mv_cesa.o
 obj-$(CONFIG_CRYPTO_DEV_TALITOS) += talitos.o
 obj-$(CONFIG_CRYPTO_DEV_IXP4XX) += ixp4xx_crypto.o
 obj-$(CONFIG_CRYPTO_DEV_PPC4XX) += amcc/

drivers/crypto/mv_cesa.h

+#ifndef __MV_CRYPTO_H__
+
+#define DIGEST_INITIAL_VAL_A	0xdd00
+#define DES_CMD_REG		0xdd58
+
+#define SEC_ACCEL_CMD		0xde00
+#define SEC_CMD_EN_SEC_ACCL0	(1 << 0)
+#define SEC_CMD_EN_SEC_ACCL1	(1 << 1)
+#define SEC_CMD_DISABLE_SEC	(1 << 2)
+
+#define SEC_ACCEL_DESC_P0	0xde04
+#define SEC_DESC_P0_PTR(x)	(x)
+
+#define SEC_ACCEL_DESC_P1	0xde14
+#define SEC_DESC_P1_PTR(x)	(x)
+
+#define SEC_ACCEL_CFG		0xde08
+#define SEC_CFG_STOP_DIG_ERR	(1 << 0)
+#define SEC_CFG_CH0_W_IDMA	(1 << 7)
+#define SEC_CFG_CH1_W_IDMA	(1 << 8)
+#define SEC_CFG_ACT_CH0_IDMA	(1 << 9)
+#define SEC_CFG_ACT_CH1_IDMA	(1 << 10)
+
+#define SEC_ACCEL_STATUS	0xde0c
+#define SEC_ST_ACT_0		(1 << 0)
+#define SEC_ST_ACT_1		(1 << 1)
+
+/*
+ * FPGA_INT_STATUS looks like a FPGA leftover and is documented only in Errata
+ * 4.12. It looks like that it was part of an IRQ-controller in FPGA and
+ * someone forgot to remove  it while switching to the core and moving to
+ * SEC_ACCEL_INT_STATUS.
+ */
+#define FPGA_INT_STATUS		0xdd68
+#define SEC_ACCEL_INT_STATUS	0xde20
+#define SEC_INT_AUTH_DONE	(1 << 0)
+#define SEC_INT_DES_E_DONE	(1 << 1)
+#define SEC_INT_AES_E_DONE	(1 << 2)
+#define SEC_INT_AES_D_DONE	(1 << 3)
+#define SEC_INT_ENC_DONE	(1 << 4)
+#define SEC_INT_ACCEL0_DONE	(1 << 5)
+#define SEC_INT_ACCEL1_DONE	(1 << 6)
+#define SEC_INT_ACC0_IDMA_DONE	(1 << 7)
+#define SEC_INT_ACC1_IDMA_DONE	(1 << 8)
+
+#define SEC_ACCEL_INT_MASK	0xde24
+
+#define AES_KEY_LEN	(8 * 4)
+
+struct sec_accel_config {
+
+	u32 config;
+#define CFG_OP_MAC_ONLY		0
+#define CFG_OP_CRYPT_ONLY	1
+#define CFG_OP_MAC_CRYPT	2
+#define CFG_OP_CRYPT_MAC	3
+#define CFG_MACM_MD5		(4 << 4)
+#define CFG_MACM_SHA1		(5 << 4)
+#define CFG_MACM_HMAC_MD5	(6 << 4)
+#define CFG_MACM_HMAC_SHA1	(7 << 4)
+#define CFG_ENCM_DES		(1 << 8)
+#define CFG_ENCM_3DES		(2 << 8)
+#define CFG_ENCM_AES		(3 << 8)
+#define CFG_DIR_ENC		(0 << 12)
+#define CFG_DIR_DEC		(1 << 12)
+#define CFG_ENC_MODE_ECB	(0 << 16)
+#define CFG_ENC_MODE_CBC	(1 << 16)
+#define CFG_3DES_EEE		(0 << 20)
+#define CFG_3DES_EDE		(1 << 20)
+#define CFG_AES_LEN_128		(0 << 24)
+#define CFG_AES_LEN_192		(1 << 24)
+#define CFG_AES_LEN_256		(2 << 24)
+
+	u32 enc_p;
+#define ENC_P_SRC(x)		(x)
+#define ENC_P_DST(x)		((x) << 16)
+
+	u32 enc_len;
+#define ENC_LEN(x)		(x)
+
+	u32 enc_key_p;
+#define ENC_KEY_P(x)		(x)
+
+	u32 enc_iv;
+#define ENC_IV_POINT(x)		((x) << 0)
+#define ENC_IV_BUF_POINT(x)	((x) << 16)
+
+	u32 mac_src_p;
+#define MAC_SRC_DATA_P(x)	(x)
+#define MAC_SRC_TOTAL_LEN(x)	((x) << 16)
+
+	u32 mac_digest;
+	u32 mac_iv;
+}__attribute__ ((packed));
+	/*
+	 * /-----------\ 0
+	 * | ACCEL CFG |	4 * 8
+	 * |-----------| 0x20
+	 * | CRYPT KEY |	8 * 4
+	 * |-----------| 0x40
+	 * |  IV   IN  |	4 * 4
+	 * |-----------| 0x40 (inplace)
+	 * |  IV BUF   |	4 * 4
+	 * |-----------| 0x50
+	 * |  DATA IN  |	16 * x (max ->max_req_size)
+	 * |-----------| 0x50 (inplace operation)
+	 * |  DATA OUT |	16 * x (max ->max_req_size)
+	 * \-----------/ SRAM size
+	 */
+#define SRAM_CONFIG		0x00
+#define SRAM_DATA_KEY_P		0x20
+#define SRAM_DATA_IV		0x40
+#define SRAM_DATA_IV_BUF	0x40
+#define SRAM_DATA_IN_START	0x50
+#define SRAM_DATA_OUT_START	0x50
+
+#define SRAM_CFG_SPACE		0x50
+
+#endif