Commit 88bc3054 authored by Michael Hennerich's avatar Michael Hennerich Committed by Greg Kroah-Hartman

IIO: ADC: New driver for AD7792/AD7793 3 Channel SPI ADC

New driver for AD7792/AD7793 3-Channel, Low Noise,
Low Power, 16-/24-Bit Sigma-Delta ADC with On-Chip In-Amp
and Reference.

The AD7792/AD7793 features a dual use data out ready DOUT/RDY output.
In order to avoid contentions on the SPI bus, it's necessary to use
spi bus locking. The DOUT/RDY output must also be wired to an
interrupt capable GPIO.

In INDIO_RING_TRIGGERED mode, this driver may block its SPI bus segment
for an extended period of time.

Changes since V1:

Use bool where applicable.
Use data buffer that lives in their own cache line.
Restructure ad7793_calibrate_all to use an array.
Use msleep.
Query REG_ID instead of doing a write/read This is a test.
Add support for unipolar mode.
Drop range attribute in favor of write scale.
Add proper locking.
Use new validate_trigger callbacks.
Use IIO_IN_DIFF for differential channels.
Change attribute naming.
Use available_scan_masks.
Some other miscellaneous cleanup (none functional changes).
Signed-off-by: default avatarMichael Hennerich <michael.hennerich@analog.com>
Acked-by: default avatarJonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 3fd47d44
......@@ -130,6 +130,20 @@ config AD7780
To compile this driver as a module, choose M here: the
module will be called ad7780.
config AD7793
tristate "Analog Devices AD7792 AD7793 ADC driver"
depends on SPI
select IIO_RING_BUFFER
select IIO_SW_RING
select IIO_TRIGGER
help
Say yes here to build support for Analog Devices
AD7792 and AD7793 SPI analog to digital convertors (ADC).
If unsure, say N (but it's safe to say "Y").
To compile this driver as a module, choose M here: the
module will be called AD7793.
config AD7745
tristate "Analog Devices AD7745, AD7746 AD7747 capacitive sensor driver"
depends on I2C
......
......@@ -35,6 +35,7 @@ obj-$(CONFIG_AD7291) += ad7291.o
obj-$(CONFIG_AD7314) += ad7314.o
obj-$(CONFIG_AD7745) += ad7745.o
obj-$(CONFIG_AD7780) += ad7780.o
obj-$(CONFIG_AD7793) += ad7793.o
obj-$(CONFIG_AD7816) += ad7816.o
obj-$(CONFIG_ADT75) += adt75.o
obj-$(CONFIG_ADT7310) += adt7310.o
......
This diff is collapsed.
/*
* AD7792/AD7793 SPI ADC driver
*
* Copyright 2011 Analog Devices Inc.
*
* Licensed under the GPL-2.
*/
#ifndef IIO_ADC_AD7793_H_
#define IIO_ADC_AD7793_H_
/*
* TODO: struct ad7793_platform_data needs to go into include/linux/iio
*/
/* Registers */
#define AD7793_REG_COMM 0 /* Communications Register (WO, 8-bit) */
#define AD7793_REG_STAT 0 /* Status Register (RO, 8-bit) */
#define AD7793_REG_MODE 1 /* Mode Register (RW, 16-bit */
#define AD7793_REG_CONF 2 /* Configuration Register (RW, 16-bit) */
#define AD7793_REG_DATA 3 /* Data Register (RO, 16-/24-bit) */
#define AD7793_REG_ID 4 /* ID Register (RO, 8-bit) */
#define AD7793_REG_IO 5 /* IO Register (RO, 8-bit) */
#define AD7793_REG_OFFSET 6 /* Offset Register (RW, 16-bit
* (AD7792)/24-bit (AD7793)) */
#define AD7793_REG_FULLSALE 7 /* Full-Scale Register
* (RW, 16-bit (AD7792)/24-bit (AD7793)) */
/* Communications Register Bit Designations (AD7793_REG_COMM) */
#define AD7793_COMM_WEN (1 << 7) /* Write Enable */
#define AD7793_COMM_WRITE (0 << 6) /* Write Operation */
#define AD7793_COMM_READ (1 << 6) /* Read Operation */
#define AD7793_COMM_ADDR(x) (((x) & 0x7) << 3) /* Register Address */
#define AD7793_COMM_CREAD (1 << 2) /* Continuous Read of Data Register */
/* Status Register Bit Designations (AD7793_REG_STAT) */
#define AD7793_STAT_RDY (1 << 7) /* Ready */
#define AD7793_STAT_ERR (1 << 6) /* Error (Overrange, Underrange) */
#define AD7793_STAT_CH3 (1 << 2) /* Channel 3 */
#define AD7793_STAT_CH2 (1 << 1) /* Channel 2 */
#define AD7793_STAT_CH1 (1 << 0) /* Channel 1 */
/* Mode Register Bit Designations (AD7793_REG_MODE) */
#define AD7793_MODE_SEL(x) (((x) & 0x7) << 13) /* Operation Mode Select */
#define AD7793_MODE_CLKSRC(x) (((x) & 0x3) << 6) /* ADC Clock Source Select */
#define AD7793_MODE_RATE(x) ((x) & 0xF) /* Filter Update Rate Select */
#define AD7793_MODE_CONT 0 /* Continuous Conversion Mode */
#define AD7793_MODE_SINGLE 1 /* Single Conversion Mode */
#define AD7793_MODE_IDLE 2 /* Idle Mode */
#define AD7793_MODE_PWRDN 3 /* Power-Down Mode */
#define AD7793_MODE_CAL_INT_ZERO 4 /* Internal Zero-Scale Calibration */
#define AD7793_MODE_CAL_INT_FULL 5 /* Internal Full-Scale Calibration */
#define AD7793_MODE_CAL_SYS_ZERO 6 /* System Zero-Scale Calibration */
#define AD7793_MODE_CAL_SYS_FULL 7 /* System Full-Scale Calibration */
#define AD7793_CLK_INT 0 /* Internal 64 kHz Clock not
* available at the CLK pin */
#define AD7793_CLK_INT_CO 1 /* Internal 64 kHz Clock available
* at the CLK pin */
#define AD7793_CLK_EXT 2 /* External 64 kHz Clock */
#define AD7793_CLK_EXT_DIV2 3 /* External Clock divided by 2 */
/* Configuration Register Bit Designations (AD7793_REG_CONF) */
#define AD7793_CONF_VBIAS(x) (((x) & 0x3) << 14) /* Bias Voltage
* Generator Enable */
#define AD7793_CONF_BO_EN (1 << 13) /* Burnout Current Enable */
#define AD7793_CONF_UNIPOLAR (1 << 12) /* Unipolar/Bipolar Enable */
#define AD7793_CONF_BOOST (1 << 11) /* Boost Enable */
#define AD7793_CONF_GAIN(x) (((x) & 0x7) << 8) /* Gain Select */
#define AD7793_CONF_REFSEL (1 << 7) /* INT/EXT Reference Select */
#define AD7793_CONF_BUF (1 << 4) /* Buffered Mode Enable */
#define AD7793_CONF_CHAN(x) ((x) & 0x7) /* Channel select */
#define AD7793_CH_AIN1P_AIN1M 0 /* AIN1(+) - AIN1(-) */
#define AD7793_CH_AIN2P_AIN2M 1 /* AIN2(+) - AIN2(-) */
#define AD7793_CH_AIN3P_AIN3M 2 /* AIN3(+) - AIN3(-) */
#define AD7793_CH_AIN1M_AIN1M 3 /* AIN1(-) - AIN1(-) */
#define AD7793_CH_TEMP 6 /* Temp Sensor */
#define AD7793_CH_AVDD_MONITOR 7 /* AVDD Monitor */
/* ID Register Bit Designations (AD7793_REG_ID) */
#define AD7792_ID 0xA
#define AD7793_ID 0xB
#define AD7793_ID_MASK 0xF
/* IO (Excitation Current Sources) Register Bit Designations (AD7793_REG_IO) */
#define AD7793_IO_IEXC1_IOUT1_IEXC2_IOUT2 0 /* IEXC1 connect to IOUT1,
* IEXC2 connect to IOUT2 */
#define AD7793_IO_IEXC1_IOUT2_IEXC2_IOUT1 1 /* IEXC1 connect to IOUT2,
* IEXC2 connect to IOUT1 */
#define AD7793_IO_IEXC1_IEXC2_IOUT1 2 /* Both current sources
* IEXC1,2 connect to IOUT1 */
#define AD7793_IO_IEXC1_IEXC2_IOUT2 3 /* Both current sources
* IEXC1,2 connect to IOUT2 */
#define AD7793_IO_IXCEN_10uA (1 << 0) /* Excitation Current 10uA */
#define AD7793_IO_IXCEN_210uA (2 << 0) /* Excitation Current 210uA */
#define AD7793_IO_IXCEN_1mA (3 << 0) /* Excitation Current 1mA */
struct ad7793_platform_data {
u16 vref_mv;
u16 mode;
u16 conf;
u8 io;
};
#endif /* IIO_ADC_AD7793_H_ */
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment