ASoC: rt5651: Add support for active-high jack detect

Some boards use a jack-receptacle with a switch which reports the
jack-inserted status as active-high, rather then the standard active-low
reporting most jacks use.

This commit adds support for it. This is activated by a boolean
"realtek,jack-detect-not-inverted" device-property. The not-inverted
in the device-property name, rather then active-high, was chosen to keep
the device-property naming consistent with the rt5640 codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

Documentation/devicetree/bindings/sound/rt5651.txt

@@ -22,6 +22,11 @@ Optional properties:
   2: Use JD1_2 pin for jack-detect
   3: Use JD2 pin for jack-detect
 
+- realtek,jack-detect-not-inverted
+  bool. Normal jack-detect switches give an inverted (active-low) signal,
+  set this bool in the rare case you've a jack-detect switch which is not
+  inverted.
+
 - realtek,over-current-threshold-microamp
   u32, micbias over-current detection threshold in µA, valid values are
   600, 1500 and 2000µA.

sound/soc/codecs/rt5651.c

@@ -1645,6 +1645,9 @@ static bool rt5651_jack_inserted(struct snd_soc_component *component)
 		break;
 	}
 
+	if (rt5651->jd_active_high)
+		return val != 0;
+	else
 		return val == 0;
 }
 
@@ -1868,20 +1871,47 @@ static void rt5651_enable_jack_detect(struct snd_soc_component *component,
 	case RT5651_JD1_1:
 		snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
 			RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_1);
-		snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
-			RT5651_JD1_1_IRQ_EN, RT5651_JD1_1_IRQ_EN);
+		/* active-low is normal, set inv flag for active-high */
+		if (rt5651->jd_active_high)
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
+				RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV);
+		else
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD1_1_IRQ_EN | RT5651_JD1_1_INV,
+				RT5651_JD1_1_IRQ_EN);
 		break;
 	case RT5651_JD1_2:
 		snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
 			RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD1_2);
-		snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
-			RT5651_JD1_2_IRQ_EN, RT5651_JD1_2_IRQ_EN);
+		/* active-low is normal, set inv flag for active-high */
+		if (rt5651->jd_active_high)
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
+				RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV);
+		else
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD1_2_IRQ_EN | RT5651_JD1_2_INV,
+				RT5651_JD1_2_IRQ_EN);
 		break;
 	case RT5651_JD2:
 		snd_soc_component_update_bits(component, RT5651_JD_CTRL2,
 			RT5651_JD_TRG_SEL_MASK, RT5651_JD_TRG_SEL_JD2);
-		snd_soc_component_update_bits(component, RT5651_IRQ_CTRL1,
-			RT5651_JD2_IRQ_EN, RT5651_JD2_IRQ_EN);
+		/* active-low is normal, set inv flag for active-high */
+		if (rt5651->jd_active_high)
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
+				RT5651_JD2_IRQ_EN | RT5651_JD2_INV);
+		else
+			snd_soc_component_update_bits(component,
+				RT5651_IRQ_CTRL1,
+				RT5651_JD2_IRQ_EN | RT5651_JD2_INV,
+				RT5651_JD2_IRQ_EN);
 		break;
 	default:
 		dev_err(component->dev, "Currently only JD1_1 / JD1_2 / JD2 are supported\n");
@@ -1986,6 +2016,9 @@ static void rt5651_apply_properties(struct snd_soc_component *component)
 				     "realtek,jack-detect-source", &val) == 0)
 		rt5651->jd_src = val;
 
+	if (device_property_read_bool(component->dev, "realtek,jack-detect-not-inverted"))
+		rt5651->jd_active_high = true;
+
 	/*
 	 * Testing on various boards has shown that good defaults for the OVCD
 	 * threshold and scale-factor are 2000µA and 0.75. For an effective

sound/soc/codecs/rt5651.h

@@ -2083,6 +2083,7 @@ struct rt5651_priv {
 	int release_count;
 	int poll_count;
 	unsigned int jd_src;
+	bool jd_active_high;
 	unsigned int ovcd_th;
 	unsigned int ovcd_sf;