dt-bindings: net: Revert sun8i dwmac binding

This binding still doesn't please everyone, and we're getting far too
close from the release to allow it to reach a stable version.

Let's remove it until the discussion settles down.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

Documentation/devicetree/bindings/net/dwmac-sun8i.txt

-* Allwinner sun8i GMAC ethernet controller
-
-This device is a platform glue layer for stmmac.
-Please see stmmac.txt for the other unchanged properties.
-
-Required properties:
-- compatible: should be one of the following string:
-		"allwinner,sun8i-a83t-emac"
-		"allwinner,sun8i-h3-emac"
-		"allwinner,sun8i-v3s-emac"
-		"allwinner,sun50i-a64-emac"
-- reg: address and length of the register for the device.
-- interrupts: interrupt for the device
-- interrupt-names: should be "macirq"
-- clocks: A phandle to the reference clock for this device
-- clock-names: should be "stmmaceth"
-- resets: A phandle to the reset control for this device
-- reset-names: should be "stmmaceth"
-- phy-mode: See ethernet.txt
-- phy-handle: See ethernet.txt
-- #address-cells: shall be 1
-- #size-cells: shall be 0
-- syscon: A phandle to the syscon of the SoC with one of the following
- compatible string:
-  - allwinner,sun8i-h3-system-controller
-  - allwinner,sun8i-v3s-system-controller
-  - allwinner,sun50i-a64-system-controller
-  - allwinner,sun8i-a83t-system-controller
-
-Optional properties:
-- allwinner,tx-delay-ps: TX clock delay chain value in ps. Range value is 0-700. Default is 0)
-- allwinner,rx-delay-ps: RX clock delay chain value in ps. Range value is 0-3100. Default is 0)
-Both delay properties need to be a multiple of 100. They control the delay for
-external PHY.
-
-Optional properties for the following compatibles:
-  - "allwinner,sun8i-h3-emac",
-  - "allwinner,sun8i-v3s-emac":
-- allwinner,leds-active-low: EPHY LEDs are active low
-
-Required child node of emac:
-- mdio bus node: should be named mdio
-
-Required properties of the mdio node:
-- #address-cells: shall be 1
-- #size-cells: shall be 0
-
-The device node referenced by "phy" or "phy-handle" should be a child node
-of the mdio node. See phy.txt for the generic PHY bindings.
-
-Required properties of the phy node with the following compatibles:
-  - "allwinner,sun8i-h3-emac",
-  - "allwinner,sun8i-v3s-emac":
-- clocks: a phandle to the reference clock for the EPHY
-- resets: a phandle to the reset control for the EPHY
-
-Example:
-
-emac: ethernet@1c0b000 {
-	compatible = "allwinner,sun8i-h3-emac";
-	syscon = <&syscon>;
-	reg = <0x01c0b000 0x104>;
-	interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
-	interrupt-names = "macirq";
-	resets = <&ccu RST_BUS_EMAC>;
-	reset-names = "stmmaceth";
-	clocks = <&ccu CLK_BUS_EMAC>;
-	clock-names = "stmmaceth";
-	#address-cells = <1>;
-	#size-cells = <0>;
-
-	phy-handle = <&int_mii_phy>;
-	phy-mode = "mii";
-	allwinner,leds-active-low;
-	mdio: mdio {
-		#address-cells = <1>;
-		#size-cells = <0>;
-		int_mii_phy: ethernet-phy@1 {
-			reg = <1>;
-			clocks = <&ccu CLK_BUS_EPHY>;
-			resets = <&ccu RST_BUS_EPHY>;
-		};
-	};
-};