iio: pressure: bmp280: Add support for BMP380 sensor family

Adds compatibility with the new generation of this sensor, the BMP380.

Includes basic sensor initialization to do pressure and temp
measurements and allows tuning oversampling settings for each channel.

The compensation algorithms are adapted from the device datasheet and
the repository https://github.com/BoschSensortec/BMP3-Sensor-API.
Signed-off-by: Angel Iglesias <ang.iglesiasg@gmail.com>
Link: https://lore.kernel.org/r/f1da2a2f1bc5bb083f318335c23b4f3d9bb8e536.1663025017.git.ang.iglesiasg@gmail.comSigned-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

drivers/iio/pressure/Kconfig

@@ -17,14 +17,14 @@ config ABP060MG
 	  will be called abp060mg.
 
 config BMP280
-	tristate "Bosch Sensortec BMP180/BMP280 pressure sensor I2C driver"
+	tristate "Bosch Sensortec BMP180/BMP280/BMP380 pressure sensor I2C driver"
 	depends on (I2C || SPI_MASTER)
 	select REGMAP
 	select BMP280_I2C if (I2C)
 	select BMP280_SPI if (SPI_MASTER)
 	help
-	  Say yes here to build support for Bosch Sensortec BMP180 and BMP280
-	  pressure and temperature sensors. Also supports the BME280 with
+	  Say yes here to build support for Bosch Sensortec BMP180, BMP280 and
+	  BMP380 pressure and temperature sensors. Also supports the BME280 with
 	  an additional humidity sensor channel.
 
 	  To compile this driver as a module, choose M here: the core module

drivers/iio/pressure/bmp280-core.c

@@ -12,6 +12,7 @@
  * https://cdn-shop.adafruit.com/datasheets/BST-BMP180-DS000-09.pdf
  * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp280-ds001.pdf
  * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bme280-ds002.pdf
+ * https://www.bosch-sensortec.com/media/boschsensortec/downloads/datasheets/bst-bmp388-ds001.pdf
  *
  * Notice:
  * The link to the bmp180 datasheet points to an outdated version missing these changes:
@@ -84,6 +85,24 @@ struct bmp280_calib {
 	s8  H6;
 };
 
+/* See datasheet Section 3.11.1. */
+struct bmp380_calib {
+	u16 T1;
+	u16 T2;
+	s8  T3;
+	s16 P1;
+	s16 P2;
+	s8  P3;
+	s8  P4;
+	u16 P5;
+	u16 P6;
+	s8  P7;
+	s8  P8;
+	s16 P9;
+	s8  P10;
+	s8  P11;
+};
+
 static const char *const bmp280_supply_names[] = {
 	"vddd", "vdda"
 };
@@ -100,6 +119,7 @@ struct bmp280_data {
 	union {
 		struct bmp180_calib bmp180;
 		struct bmp280_calib bmp280;
+		struct bmp380_calib bmp380;
 	} calib;
 	struct regulator_bulk_data supplies[BMP280_NUM_SUPPLIES];
 	unsigned int start_up_time; /* in microseconds */
@@ -125,6 +145,7 @@ struct bmp280_data {
 		/* Calibration data buffers */
 		__le16 bmp280_cal_buf[BMP280_CONTIGUOUS_CALIB_REGS / 2];
 		__be16 bmp180_cal_buf[BMP180_REG_CALIB_COUNT / 2];
+		u8 bmp380_cal_buf[BMP380_CALIB_REG_COUNT];
 		/* Miscellaneous, endianess-aware data buffers */
 		__le16 le16;
 		__be16 be16;
@@ -162,6 +183,25 @@ struct bmp280_chip_info {
  */
 enum { T1, T2, T3, P1, P2, P3, P4, P5, P6, P7, P8, P9 };
 
+enum {
+	/* Temperature calib indexes */
+	BMP380_T1 = 0,
+	BMP380_T2 = 2,
+	BMP380_T3 = 4,
+	/* Pressure calib indexes */
+	BMP380_P1 = 5,
+	BMP380_P2 = 7,
+	BMP380_P3 = 9,
+	BMP380_P4 = 10,
+	BMP380_P5 = 11,
+	BMP380_P6 = 13,
+	BMP380_P7 = 15,
+	BMP380_P8 = 16,
+	BMP380_P9 = 17,
+	BMP380_P10 = 19,
+	BMP380_P11 = 20,
+};
+
 static const struct iio_chan_spec bmp280_channels[] = {
 	{
 		.type = IIO_PRESSURE,
@@ -745,6 +785,342 @@ static const struct bmp280_chip_info bme280_chip_info = {
 	.read_calib = bme280_read_calib,
 };
 
+/*
+ * Helper function to send a command to BMP3XX sensors.
+ *
+ * Sensor processes commands written to the CMD register and signals
+ * execution result through "cmd_rdy" and "cmd_error" flags available on
+ * STATUS and ERROR registers.
+ */
+static int bmp380_cmd(struct bmp280_data *data, u8 cmd)
+{
+	unsigned int reg;
+	int ret;
+
+	/* Check if device is ready to process a command */
+	ret = regmap_read(data->regmap, BMP380_REG_STATUS, &reg);
+	if (ret) {
+		dev_err(data->dev, "failed to read error register\n");
+		return ret;
+	}
+	if (!(reg & BMP380_STATUS_CMD_RDY_MASK)) {
+		dev_err(data->dev, "device is not ready to accept commands\n");
+		return -EBUSY;
+	}
+
+	/* Send command to process */
+	ret = regmap_write(data->regmap, BMP380_REG_CMD, cmd);
+	if (ret) {
+		dev_err(data->dev, "failed to send command to device\n");
+		return ret;
+	}
+	/* Wait for 2ms for command to be processed */
+	usleep_range(data->start_up_time, data->start_up_time + 100);
+	/* Check for command processing error */
+	ret = regmap_read(data->regmap, BMP380_REG_ERROR, &reg);
+	if (ret) {
+		dev_err(data->dev, "error reading ERROR reg\n");
+		return ret;
+	}
+	if (reg & BMP380_ERR_CMD_MASK) {
+		dev_err(data->dev, "error processing command 0x%X\n", cmd);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/*
+ * Returns temperature in Celsius dregrees, resolution is 0.01º C. Output value of
+ * "5123" equals 51.2º C. t_fine carries fine temperature as global value.
+ *
+ * Taken from datasheet, Section Appendix 9, "Compensation formula" and repo
+ * https://github.com/BoschSensortec/BMP3-Sensor-API.
+ */
+static s32 bmp380_compensate_temp(struct bmp280_data *data, u32 adc_temp)
+{
+	s64 var1, var2, var3, var4, var5, var6, comp_temp;
+	struct bmp380_calib *calib = &data->calib.bmp380;
+
+	var1 = ((s64) adc_temp) - (((s64) calib->T1) << 8);
+	var2 = var1 * ((s64) calib->T2);
+	var3 = var1 * var1;
+	var4 = var3 * ((s64) calib->T3);
+	var5 = (var2 << 18) + var4;
+	var6 = var5 >> 32;
+	data->t_fine = (s32) var6;
+	comp_temp = (var6 * 25) >> 14;
+
+	comp_temp = clamp_val(comp_temp, BMP380_MIN_TEMP, BMP380_MAX_TEMP);
+	return (s32) comp_temp;
+}
+
+/*
+ * Returns pressure in Pa as an unsigned 32 bit integer in fractional Pascal.
+ * Output value of "9528709" represents 9528709/100 = 95287.09 Pa = 952.8709 hPa.
+ *
+ * Taken from datasheet, Section 9.3. "Pressure compensation" and repository
+ * https://github.com/BoschSensortec/BMP3-Sensor-API.
+ */
+static u32 bmp380_compensate_press(struct bmp280_data *data, u32 adc_press)
+{
+	s64 var1, var2, var3, var4, var5, var6, offset, sensitivity;
+	struct bmp380_calib *calib = &data->calib.bmp380;
+	u32 comp_press;
+
+	var1 = (s64)data->t_fine * (s64)data->t_fine;
+	var2 = var1 >> 6;
+	var3 = (var2 * ((s64) data->t_fine)) >> 8;
+	var4 = ((s64)calib->P8 * var3) >> 5;
+	var5 = ((s64)calib->P7 * var1) << 4;
+	var6 = ((s64)calib->P6 * (s64)data->t_fine) << 22;
+	offset = ((s64)calib->P5 << 47) + var4 + var5 + var6;
+	var2 = ((s64)calib->P4 * var3) >> 5;
+	var4 = ((s64)calib->P3 * var1) << 2;
+	var5 = ((s64)calib->P2 - ((s64)1 << 14)) *
+	       ((s64)data->t_fine << 21);
+	sensitivity = (((s64) calib->P1 - ((s64) 1 << 14)) << 46) +
+			var2 + var4 + var5;
+	var1 = (sensitivity >> 24) * (s64)adc_press;
+	var2 = (s64)calib->P10 * (s64)data->t_fine;
+	var3 = var2 + ((s64)calib->P9 << 16);
+	var4 = (var3 * (s64)adc_press) >> 13;
+
+	/*
+	 * Dividing by 10 followed by multiplying by 10 to avoid
+	 * possible overflow caused by (uncomp_data->pressure * partial_data4).
+	 */
+	var5 = ((s64)adc_press * div_s64(var4, 10)) >> 9;
+	var5 *= 10;
+	var6 = (s64)adc_press * (s64)adc_press;
+	var2 = ((s64)calib->P11 * var6) >> 16;
+	var3 = (var2 * (s64)adc_press) >> 7;
+	var4 = (offset >> 2) + var1 + var5 + var3;
+	comp_press = ((u64)var4 * 25) >> 40;
+
+	comp_press = clamp_val(comp_press, BMP380_MIN_PRES, BMP380_MAX_PRES);
+	return comp_press;
+}
+
+static int bmp380_read_temp(struct bmp280_data *data, int *val)
+{
+	s32 comp_temp;
+	u32 adc_temp;
+	int ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_TEMP_XLSB,
+			       data->buf, sizeof(data->buf));
+	if (ret) {
+		dev_err(data->dev, "failed to read temperature\n");
+		return ret;
+	}
+
+	adc_temp = get_unaligned_le24(data->buf);
+	if (adc_temp == BMP380_TEMP_SKIPPED) {
+		dev_err(data->dev, "reading temperature skipped\n");
+		return -EIO;
+	}
+	comp_temp = bmp380_compensate_temp(data, adc_temp);
+
+	/*
+	 * Val might be NULL if we're called by the read_press routine,
+	 * who only cares about the carry over t_fine value.
+	 */
+	if (val) {
+		/* IIO reports temperatures in milli Celsius */
+		*val = comp_temp * 10;
+		return IIO_VAL_INT;
+	}
+
+	return 0;
+}
+
+static int bmp380_read_press(struct bmp280_data *data, int *val, int *val2)
+{
+	s32 comp_press;
+	u32 adc_press;
+	int ret;
+
+	/* Read and compensate for temperature so we get a reading of t_fine */
+	ret = bmp380_read_temp(data, NULL);
+	if (ret)
+		return ret;
+
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_PRESS_XLSB,
+			       data->buf, sizeof(data->buf));
+	if (ret) {
+		dev_err(data->dev, "failed to read pressure\n");
+		return ret;
+	}
+
+	adc_press = get_unaligned_le24(data->buf);
+	if (adc_press == BMP380_PRESS_SKIPPED) {
+		dev_err(data->dev, "reading pressure skipped\n");
+		return -EIO;
+	}
+	comp_press = bmp380_compensate_press(data, adc_press);
+
+	*val = comp_press;
+	/* Compensated pressure is in cPa (centipascals) */
+	*val2 = 100000;
+
+	return IIO_VAL_FRACTIONAL;
+}
+
+static int bmp380_read_calib(struct bmp280_data *data)
+{
+	struct bmp380_calib *calib = &data->calib.bmp380;
+	int ret;
+
+	/* Read temperature and pressure calibration data */
+	ret = regmap_bulk_read(data->regmap, BMP380_REG_CALIB_TEMP_START,
+			       data->bmp380_cal_buf, sizeof(data->bmp380_cal_buf));
+	if (ret) {
+		dev_err(data->dev,
+			"failed to read temperature calibration parameters\n");
+		return ret;
+	}
+
+	/* Toss the temperature calibration data into the entropy pool */
+	add_device_randomness(data->bmp380_cal_buf, sizeof(data->bmp380_cal_buf));
+
+	/* Parse calibration values */
+	calib->T1 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_T1]);
+	calib->T2 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_T2]);
+	calib->T3 = data->bmp380_cal_buf[BMP380_T3];
+	calib->P1 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P1]);
+	calib->P2 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P2]);
+	calib->P3 = data->bmp380_cal_buf[BMP380_P3];
+	calib->P4 = data->bmp380_cal_buf[BMP380_P4];
+	calib->P5 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P5]);
+	calib->P6 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P6]);
+	calib->P7 = data->bmp380_cal_buf[BMP380_P7];
+	calib->P8 = data->bmp380_cal_buf[BMP380_P8];
+	calib->P9 = get_unaligned_le16(&data->bmp380_cal_buf[BMP380_P9]);
+	calib->P10 = data->bmp380_cal_buf[BMP380_P10];
+	calib->P11 = data->bmp380_cal_buf[BMP380_P11];
+
+	return 0;
+}
+
+static int bmp380_chip_config(struct bmp280_data *data)
+{
+	bool change = false, aux;
+	unsigned int tmp;
+	u8 osrs;
+	int ret;
+
+	/* Configure power control register */
+	ret = regmap_update_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+				 BMP380_CTRL_SENSORS_MASK,
+				 BMP380_CTRL_SENSORS_PRESS_EN |
+				 BMP380_CTRL_SENSORS_TEMP_EN);
+	if (ret) {
+		dev_err(data->dev,
+			"failed to write operation control register\n");
+		return ret;
+	}
+
+	/* Configure oversampling */
+	osrs = FIELD_PREP(BMP380_OSRS_TEMP_MASK, data->oversampling_temp) |
+	       FIELD_PREP(BMP380_OSRS_PRESS_MASK, data->oversampling_press);
+
+	ret = regmap_update_bits_check(data->regmap, BMP380_REG_OSR,
+				       BMP380_OSRS_TEMP_MASK |
+				       BMP380_OSRS_PRESS_MASK,
+				       osrs, &aux);
+	if (ret) {
+		dev_err(data->dev, "failed to write oversampling register\n");
+		return ret;
+	}
+	change = change || aux;
+
+	/* Configure output data rate */
+	ret = regmap_update_bits(data->regmap, BMP380_REG_ODR,
+				 BMP380_ODRS_MASK, BMP380_ODRS_50HZ);
+	if (ret) {
+		dev_err(data->dev, "failed to write ODR selection register\n");
+		return ret;
+	}
+
+	/* Set filter data */
+	ret = regmap_update_bits(data->regmap, BMP380_REG_CONFIG,
+				 BMP380_FILTER_MASK,
+				 FIELD_PREP(BMP380_FILTER_MASK, BMP380_FILTER_3X));
+	if (ret) {
+		dev_err(data->dev, "failed to write config register\n");
+		return ret;
+	}
+
+	if (change) {
+		/*
+		 * The configurations errors are detected on the fly during a measurement
+		 * cycle. If the sampling frequency is too low, it's faster to reset
+		 * the measurement loop than wait until the next measurement is due.
+		 *
+		 * Resets sensor measurement loop toggling between sleep and normal
+		 * operating modes.
+		 */
+		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+					BMP380_MODE_MASK,
+					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_SLEEP));
+		if (ret) {
+			dev_err(data->dev, "failed to set sleep mode\n");
+			return ret;
+		}
+		usleep_range(2000, 2500);
+		ret = regmap_write_bits(data->regmap, BMP380_REG_POWER_CONTROL,
+					BMP380_MODE_MASK,
+					FIELD_PREP(BMP380_MODE_MASK, BMP380_MODE_NORMAL));
+		if (ret) {
+			dev_err(data->dev, "failed to set normal mode\n");
+			return ret;
+		}
+		/*
+		 * Waits for measurement before checking configuration error flag.
+		 * Selected longest measure time indicated in section 3.9.1
+		 * in the datasheet.
+		 */
+		msleep(80);
+
+		/* Check config error flag */
+		ret = regmap_read(data->regmap, BMP380_REG_ERROR, &tmp);
+		if (ret) {
+			dev_err(data->dev,
+				"failed to read error register\n");
+			return ret;
+		}
+		if (tmp & BMP380_ERR_CONF_MASK) {
+			dev_warn(data->dev,
+				"sensor flagged configuration as incompatible\n");
+			return -EINVAL;
+		}
+	}
+
+	return 0;
+}
+
+static const int bmp380_oversampling_avail[] = { 1, 2, 4, 8, 16, 32 };
+
+static const struct bmp280_chip_info bmp380_chip_info = {
+	.id_reg = BMP380_REG_ID,
+	.start_up_time = 2000,
+	.num_channels = 2,
+
+	.oversampling_temp_avail = bmp380_oversampling_avail,
+	.num_oversampling_temp_avail = ARRAY_SIZE(bmp380_oversampling_avail),
+	.oversampling_temp_default = ilog2(1),
+
+	.oversampling_press_avail = bmp380_oversampling_avail,
+	.num_oversampling_press_avail = ARRAY_SIZE(bmp380_oversampling_avail),
+	.oversampling_press_default = ilog2(4),
+
+	.chip_config = bmp380_chip_config,
+	.read_temp = bmp380_read_temp,
+	.read_press = bmp380_read_press,
+	.read_calib = bmp380_read_calib,
+};
+
 static int bmp180_measure(struct bmp280_data *data, u8 ctrl_meas)
 {
 	const int conversion_time_max[] = { 4500, 7500, 13500, 25500 };
@@ -1092,6 +1468,9 @@ int bmp280_common_probe(struct device *dev,
 	case BME280_CHIP_ID:
 		chip_info = &bme280_chip_info;
 		break;
+	case BMP380_CHIP_ID:
+		chip_info = &bmp380_chip_info;
+		break;
 	default:
 		return -EINVAL;
 	}
@@ -1149,6 +1528,13 @@ int bmp280_common_probe(struct device *dev,
 		return -EINVAL;
 	}
 
+	/* BMP3xx requires soft-reset as part of initialization */
+	if (chip_id == BMP380_CHIP_ID) {
+		ret = bmp380_cmd(data, BMP380_CMD_SOFT_RESET);
+		if (ret < 0)
+			return ret;
+	}
+
 	ret = data->chip_info->chip_config(data);
 	if (ret < 0)
 		return ret;

drivers/iio/pressure/bmp280-i2c.c

@@ -19,6 +19,9 @@ static int bmp280_i2c_probe(struct i2c_client *client,
 	case BME280_CHIP_ID:
 		regmap_config = &bmp280_regmap_config;
 		break;
+	case BMP380_CHIP_ID:
+		regmap_config = &bmp380_regmap_config;
+		break;
 	default:
 		return -EINVAL;
 	}
@@ -41,6 +44,7 @@ static const struct of_device_id bmp280_of_i2c_match[] = {
 	{ .compatible = "bosch,bmp180", .data = (void *)BMP180_CHIP_ID },
 	{ .compatible = "bosch,bmp280", .data = (void *)BMP280_CHIP_ID },
 	{ .compatible = "bosch,bme280", .data = (void *)BME280_CHIP_ID },
+	{ .compatible = "bosch,bmp380", .data = (void *)BMP380_CHIP_ID },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, bmp280_of_i2c_match);
@@ -50,6 +54,7 @@ static const struct i2c_device_id bmp280_i2c_id[] = {
 	{"bmp180", BMP180_CHIP_ID },
 	{"bmp280", BMP280_CHIP_ID },
 	{"bme280", BME280_CHIP_ID },
+	{"bmp380", BMP380_CHIP_ID },
 	{ },
 };
 MODULE_DEVICE_TABLE(i2c, bmp280_i2c_id);

drivers/iio/pressure/bmp280-regmap.c

@@ -72,6 +72,49 @@ static bool bmp280_is_volatile_reg(struct device *dev, unsigned int reg)
 	}
 }
 
+static bool bmp380_is_writeable_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP380_REG_CMD:
+	case BMP380_REG_CONFIG:
+	case BMP380_REG_FIFO_CONFIG_1:
+	case BMP380_REG_FIFO_CONFIG_2:
+	case BMP380_REG_FIFO_WATERMARK_LSB:
+	case BMP380_REG_FIFO_WATERMARK_MSB:
+	case BMP380_REG_POWER_CONTROL:
+	case BMP380_REG_INT_CONTROL:
+	case BMP380_REG_IF_CONFIG:
+	case BMP380_REG_ODR:
+	case BMP380_REG_OSR:
+		return true;
+	default:
+		return false;
+	}
+}
+
+static bool bmp380_is_volatile_reg(struct device *dev, unsigned int reg)
+{
+	switch (reg) {
+	case BMP380_REG_TEMP_XLSB:
+	case BMP380_REG_TEMP_LSB:
+	case BMP380_REG_TEMP_MSB:
+	case BMP380_REG_PRESS_XLSB:
+	case BMP380_REG_PRESS_LSB:
+	case BMP380_REG_PRESS_MSB:
+	case BMP380_REG_SENSOR_TIME_XLSB:
+	case BMP380_REG_SENSOR_TIME_LSB:
+	case BMP380_REG_SENSOR_TIME_MSB:
+	case BMP380_REG_INT_STATUS:
+	case BMP380_REG_FIFO_DATA:
+	case BMP380_REG_STATUS:
+	case BMP380_REG_ERROR:
+	case BMP380_REG_EVENT:
+		return true;
+	default:
+		return false;
+	}
+}
+
 const struct regmap_config bmp280_regmap_config = {
 	.reg_bits = 8,
 	.val_bits = 8,
@@ -83,3 +126,15 @@ const struct regmap_config bmp280_regmap_config = {
 	.volatile_reg = bmp280_is_volatile_reg,
 };
 EXPORT_SYMBOL_NS(bmp280_regmap_config, IIO_BMP280);
+
+const struct regmap_config bmp380_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+
+	.max_register = BMP380_REG_CMD,
+	.cache_type = REGCACHE_RBTREE,
+
+	.writeable_reg = bmp380_is_writeable_reg,
+	.volatile_reg = bmp380_is_volatile_reg,
+};
+EXPORT_SYMBOL_NS(bmp380_regmap_config, IIO_BMP280);

drivers/iio/pressure/bmp280-spi.c

@@ -66,6 +66,9 @@ static int bmp280_spi_probe(struct spi_device *spi)
 	case BME280_CHIP_ID:
 		regmap_config = &bmp280_regmap_config;
 		break;
+	case BMP380_CHIP_ID:
+		regmap_config = &bmp380_regmap_config;
+		break;
 	default:
 		return -EINVAL;
 	}
@@ -92,6 +95,7 @@ static const struct of_device_id bmp280_of_spi_match[] = {
 	{ .compatible = "bosch,bmp181", },
 	{ .compatible = "bosch,bmp280", },
 	{ .compatible = "bosch,bme280", },
+	{ .compatible = "bosch,bmp380", },
 	{ },
 };
 MODULE_DEVICE_TABLE(of, bmp280_of_spi_match);
@@ -101,6 +105,7 @@ static const struct spi_device_id bmp280_spi_id[] = {
 	{ "bmp181", BMP180_CHIP_ID },
 	{ "bmp280", BMP280_CHIP_ID },
 	{ "bme280", BME280_CHIP_ID },
+	{ "bmp380", BMP380_CHIP_ID },
 	{ }
 };
 MODULE_DEVICE_TABLE(spi, bmp280_spi_id);

drivers/iio/pressure/bmp280.h

@@ -3,6 +3,105 @@
 #include <linux/device.h>
 #include <linux/regmap.h>
 
+/* BMP380 specific registers */
+#define BMP380_REG_CMD			0x7E
+#define BMP380_REG_CONFIG		0x1F
+#define BMP380_REG_ODR			0x1D
+#define BMP380_REG_OSR			0x1C
+#define BMP380_REG_POWER_CONTROL	0x1B
+#define BMP380_REG_IF_CONFIG		0x1A
+#define BMP380_REG_INT_CONTROL		0x19
+#define BMP380_REG_INT_STATUS		0x11
+#define BMP380_REG_EVENT		0x10
+#define BMP380_REG_STATUS		0x03
+#define BMP380_REG_ERROR		0x02
+#define BMP380_REG_ID			0x00
+
+#define BMP380_REG_FIFO_CONFIG_1	0x18
+#define BMP380_REG_FIFO_CONFIG_2	0x17
+#define BMP380_REG_FIFO_WATERMARK_MSB	0x16
+#define BMP380_REG_FIFO_WATERMARK_LSB	0x15
+#define BMP380_REG_FIFO_DATA		0x14
+#define BMP380_REG_FIFO_LENGTH_MSB	0x13
+#define BMP380_REG_FIFO_LENGTH_LSB	0x12
+
+#define BMP380_REG_SENSOR_TIME_MSB	0x0E
+#define BMP380_REG_SENSOR_TIME_LSB	0x0D
+#define BMP380_REG_SENSOR_TIME_XLSB	0x0C
+
+#define BMP380_REG_TEMP_MSB		0x09
+#define BMP380_REG_TEMP_LSB		0x08
+#define BMP380_REG_TEMP_XLSB		0x07
+
+#define BMP380_REG_PRESS_MSB		0x06
+#define BMP380_REG_PRESS_LSB		0x05
+#define BMP380_REG_PRESS_XLSB		0x04
+
+#define BMP380_REG_CALIB_TEMP_START	0x31
+#define BMP380_CALIB_REG_COUNT		21
+
+#define BMP380_FILTER_MASK		GENMASK(3, 1)
+#define BMP380_FILTER_OFF		0
+#define BMP380_FILTER_1X		1
+#define BMP380_FILTER_3X		2
+#define BMP380_FILTER_7X		3
+#define BMP380_FILTER_15X		4
+#define BMP380_FILTER_31X		5
+#define BMP380_FILTER_63X		6
+#define BMP380_FILTER_127X		7
+
+#define BMP380_OSRS_TEMP_MASK		GENMASK(5, 3)
+#define BMP380_OSRS_PRESS_MASK		GENMASK(2, 0)
+
+#define BMP380_ODRS_MASK		GENMASK(4, 0)
+#define BMP380_ODRS_200HZ		0x00
+#define BMP380_ODRS_100HZ		0x01
+#define BMP380_ODRS_50HZ		0x02
+#define BMP380_ODRS_25HZ		0x03
+#define BMP380_ODRS_12_5HZ		0x04
+#define BMP380_ODRS_6_25HZ		0x05
+#define BMP380_ODRS_3_1HZ		0x06
+#define BMP380_ODRS_1_5HZ		0x07
+#define BMP380_ODRS_0_78HZ		0x08
+#define BMP380_ODRS_0_39HZ		0x09
+#define BMP380_ODRS_0_2HZ		0x0A
+#define BMP380_ODRS_0_1HZ		0x0B
+#define BMP380_ODRS_0_05HZ		0x0C
+#define BMP380_ODRS_0_02HZ		0x0D
+#define BMP380_ODRS_0_01HZ		0x0E
+#define BMP380_ODRS_0_006HZ		0x0F
+#define BMP380_ODRS_0_003HZ		0x10
+#define BMP380_ODRS_0_0015HZ		0x11
+
+#define BMP380_CTRL_SENSORS_MASK	GENMASK(1, 0)
+#define BMP380_CTRL_SENSORS_PRESS_EN	BIT(0)
+#define BMP380_CTRL_SENSORS_TEMP_EN	BIT(1)
+#define BMP380_MODE_MASK		GENMASK(5, 4)
+#define BMP380_MODE_SLEEP		0
+#define BMP380_MODE_FORCED		1
+#define BMP380_MODE_NORMAL		3
+
+#define BMP380_MIN_TEMP			-4000
+#define BMP380_MAX_TEMP			8500
+#define BMP380_MIN_PRES			3000000
+#define BMP380_MAX_PRES			12500000
+
+#define BMP380_CMD_NOOP			0x00
+#define BMP380_CMD_EXTMODE_EN_MID	0x34
+#define BMP380_CMD_FIFO_FLUSH		0xB0
+#define BMP380_CMD_SOFT_RESET		0xB6
+
+#define BMP380_STATUS_CMD_RDY_MASK	BIT(4)
+#define BMP380_STATUS_DRDY_PRESS_MASK	BIT(5)
+#define BMP380_STATUS_DRDY_TEMP_MASK	BIT(6)
+
+#define BMP380_ERR_FATAL_MASK		BIT(0)
+#define BMP380_ERR_CMD_MASK		BIT(1)
+#define BMP380_ERR_CONF_MASK		BIT(2)
+
+#define BMP380_TEMP_SKIPPED		0x800000
+#define BMP380_PRESS_SKIPPED		0x800000
+
 /* BMP280 specific registers */
 #define BMP280_REG_HUMIDITY_LSB		0xFE
 #define BMP280_REG_HUMIDITY_MSB		0xFD
@@ -99,6 +198,7 @@
 #define BMP280_REG_RESET		0xE0
 #define BMP280_REG_ID			0xD0
 
+#define BMP380_CHIP_ID			0x50
 #define BMP180_CHIP_ID			0x55
 #define BMP280_CHIP_ID			0x58
 #define BME280_CHIP_ID			0x60
@@ -112,6 +212,7 @@
 /* Regmap configurations */
 extern const struct regmap_config bmp180_regmap_config;
 extern const struct regmap_config bmp280_regmap_config;
+extern const struct regmap_config bmp380_regmap_config;
 
 /* Probe called from different transports */
 int bmp280_common_probe(struct device *dev,