serial: stm32: fix code cleaning warnings and checks

Fixes checkpatch --strict warnings and checks:
- checkpatch --strict "Unnecessary parentheses"
- checkpatch --strict "Blank lines aren't necessary before a close brace
- checkpatch --strict "Alignment should match open parenthesis"
- checkpatch --strict "Please don't use multiple blank lines"
- checkpatch --strict "Comparison to NULL could be written ..."
- visual check code ordering warning
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-3-erwan.leray@foss.st.comSigned-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

drivers/tty/serial/stm32-usart.c

@@ -176,8 +176,7 @@ static int stm32_pending_rx(struct uart_port *port, u32 *sr, int *last_res,
 		status = dmaengine_tx_status(stm32_port->rx_ch,
 					     stm32_port->rx_ch->cookie,
 					     &state);
-		if ((status == DMA_IN_PROGRESS) &&
-		    (*last_res != state.residue))
+		if (status == DMA_IN_PROGRESS && (*last_res != state.residue))
 			return 1;
 		else
 			return 0;
@@ -464,7 +463,7 @@ static irqreturn_t stm32_interrupt(int irq, void *ptr)
 		writel_relaxed(USART_ICR_RTOCF,
 			       port->membase + ofs->icr);
 
-	if ((sr & USART_SR_WUF) && (ofs->icr != UNDEF_REG))
+	if ((sr & USART_SR_WUF) && ofs->icr != UNDEF_REG)
 		writel_relaxed(USART_ICR_WUCF,
 			       port->membase + ofs->icr);
 
@@ -620,7 +619,6 @@ static void stm32_stop_rx(struct uart_port *port)
 	stm32_clr_bits(port, ofs->cr1, stm32_port->cr1_irq);
 	if (stm32_port->cr3_irq)
 		stm32_clr_bits(port, ofs->cr3, stm32_port->cr3_irq);
-
 }
 
 /* Handle breaks - ignored by us */
@@ -973,18 +971,17 @@ static int stm32_init_port(struct stm32_port *stm32port,
 	struct resource *res;
 	int ret;
 
+	ret = platform_get_irq(pdev, 0);
+	if (ret <= 0)
+		return ret ? : -ENODEV;
+
 	port->iotype	= UPIO_MEM;
 	port->flags	= UPF_BOOT_AUTOCONF;
 	port->ops	= &stm32_uart_ops;
 	port->dev	= &pdev->dev;
 	port->fifosize	= stm32port->info->cfg.fifosize;
 	port->has_sysrq = IS_ENABLED(CONFIG_SERIAL_STM32_CONSOLE);
-
-	ret = platform_get_irq(pdev, 0);
-	if (ret <= 0)
-		return ret ? : -ENODEV;
 	port->irq = ret;
-
 	port->rs485_config = stm32_config_rs485;
 
 	ret = stm32_init_rs485(port, pdev);
@@ -1322,7 +1319,6 @@ static int stm32_serial_remove(struct platform_device *pdev)
 	return err;
 }
 
-
 #ifdef CONFIG_SERIAL_STM32_CONSOLE
 static void stm32_console_putchar(struct uart_port *port, int ch)
 {
@@ -1335,7 +1331,8 @@ static void stm32_console_putchar(struct uart_port *port, int ch)
 	writel_relaxed(ch, port->membase + ofs->tdr);
 }
 
-static void stm32_console_write(struct console *co, const char *s, unsigned cnt)
+static void stm32_console_write(struct console *co, const char *s,
+				unsigned int cnt)
 {
 	struct uart_port *port = &stm32_ports[co->index].port;
 	struct stm32_port *stm32_port = to_stm32_port(port);
@@ -1388,7 +1385,7 @@ static int stm32_console_setup(struct console *co, char *options)
 	 * this to be called during the uart port registration when the
 	 * driver gets probed and the port should be mapped at that point.
 	 */
-	if (stm32port->port.mapbase == 0 || stm32port->port.membase == NULL)
+	if (stm32port->port.mapbase == 0 || !stm32port->port.membase)
 		return -ENXIO;
 
 	if (options)