Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM soc board specific updates from Olof Johansson:
 "Misc board updates:
   - Greg added a handful of boards to KS8695 (since he has stepped up
     to maintain it).
   - Qualcomm has added DT-only board support for a couple of their
     newer SoCs.
   - misc other updates for Samsung and Freescale boards."

Fix up trivial conflict in arch/arm/mach-shmobile/board-armadillo800eva.c
due to gpio device data being added next to hdmi device data that got moved.

* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: msm: Allow 8960 and 8660 to compile together
  ARM: msm: Allow msm_iomap-8x60 and msm_iomap-8960 to coexist
  ARM: EXYNOS: Add generic PWM lookup support for SMDKV310
  ARM: EXYNOS: Add generic PWM lookup support for SMDK4X12
  ARM: EXYNOS: Use generic pwm driver in Origen board
  ARM: shmobile: armadillo800eva: Add support RTC
  ARM: ks8695: add board support for the OpenGear boards based on the KS8695
  ARM: ks8695: add board support for the SnapGear boards based on the KS8695
  ARM: dts: Add heartbeat gpio-leds support to Origen
  ARM: dts: Use active low flag for gpio-keys on Origen
  ARM: shmobile: marzen: enable thermal sensor
  ARM: shmobile: marzen: fixup regulator id for smsc911x
  ARM: shmobile: marzen: add SDHI0 support
  ARM: mmp: enable debug uart port in defconfig
  ARM: mmp: implement DEBUG_LL port choice
  ARM: S3C64XX: Register audio platform devices for Bells on Cragganmore
  ARM: S3C64XX: Update configuration for WM5102 module on Cragganmore
  ARM: mx27pdk: Add audio support
  ARM: ttc_dkb: add nand support

arch/arm/Kconfig.debug

@@ -224,6 +224,20 @@ choice
 		  Say Y here if you want kernel low-level debugging support
 		  on i.MX6Q UART4.
 
+	config DEBUG_MMP_UART2
+		bool "Kernel low-level debugging message via MMP UART2"
+		depends on ARCH_MMP
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on MMP UART2.
+
+	config DEBUG_MMP_UART3
+		bool "Kernel low-level debugging message via MMP UART3"
+		depends on ARCH_MMP
+		help
+		  Say Y here if you want kernel low-level debugging support
+		  on MMP UART3.
+
 	config DEBUG_MSM_UART1
 		bool "Kernel low-level debugging messages via MSM UART1"
 		depends on ARCH_MSM7X00A || ARCH_MSM7X30 || ARCH_QSD8X50

arch/arm/boot/dts/exynos4210-origen.dts

@@ -62,35 +62,43 @@ gpio_keys {
 
 		up {
 			label = "Up";
-			gpios = <&gpx2 0 0 0 2>;
+			gpios = <&gpx2 0 0 0x10000 2>;
 			linux,code = <103>;
 		};
 
 		down {
 			label = "Down";
-			gpios = <&gpx2 1 0 0 2>;
+			gpios = <&gpx2 1 0 0x10000 2>;
 			linux,code = <108>;
 		};
 
 		back {
 			label = "Back";
-			gpios = <&gpx1 7 0 0 2>;
+			gpios = <&gpx1 7 0 0x10000 2>;
 			linux,code = <158>;
 		};
 
 		home {
 			label = "Home";
-			gpios = <&gpx1 6 0 0 2>;
+			gpios = <&gpx1 6 0 0x10000 2>;
 			linux,code = <102>;
 		};
 
 		menu {
 			label = "Menu";
-			gpios = <&gpx1 5 0 0 2>;
+			gpios = <&gpx1 5 0 0x10000 2>;
 			linux,code = <139>;
 		};
 	};
 
+	leds {
+		compatible = "gpio-leds";
+		status {
+			gpios = <&gpx1 3 0 0x10000 2>;
+			linux,default-trigger = "heartbeat";
+		};
+	};
+
 	keypad@100A0000 {
 		status = "disabled";
 	};

arch/arm/configs/armadillo800eva_defconfig

@@ -85,6 +85,7 @@ CONFIG_SERIAL_SH_SCI_NR_UARTS=8
 CONFIG_SERIAL_SH_SCI_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_I2C=y
+CONFIG_I2C_GPIO=y
 CONFIG_I2C_SH_MOBILE=y
 # CONFIG_HWMON is not set
 CONFIG_MEDIA_SUPPORT=y
@@ -120,6 +121,8 @@ CONFIG_USB_ETH=m
 CONFIG_MMC=y
 CONFIG_MMC_SDHI=y
 CONFIG_MMC_SH_MMCIF=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_DRV_S35390A=y
 CONFIG_DMADEVICES=y
 CONFIG_SH_DMAE=y
 CONFIG_UIO=y

arch/arm/configs/marzen_defconfig

@@ -68,6 +68,8 @@ CONFIG_SERIAL_SH_SCI_CONSOLE=y
 # CONFIG_HW_RANDOM is not set
 CONFIG_GPIO_SYSFS=y
 # CONFIG_HWMON is not set
+CONFIG_THERMAL=y
+CONFIG_RCAR_THERMAL=y
 CONFIG_SSB=y
 # CONFIG_HID_SUPPORT is not set
 # CONFIG_USB_SUPPORT is not set

arch/arm/configs/mmp2_defconfig

@@ -16,7 +16,7 @@ CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255"
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.1.100:/nfsroot/ ip=192.168.1.101:192.168.1.100::255.255.255.0::eth0:on console=ttyS2,38400 mem=128M user_debug=255 earlyprintk"
 CONFIG_VFP=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -90,6 +90,9 @@ CONFIG_DEBUG_INFO=y
 # CONFIG_RCU_CPU_STALL_DETECTOR is not set
 # CONFIG_DYNAMIC_DEBUG is not set
 CONFIG_DEBUG_USER=y
+CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_MMP_UART3=y
+CONFIG_EARLY_PRINTK=y
 CONFIG_DEBUG_ERRORS=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_CRC_CCITT=y

arch/arm/configs/pxa910_defconfig

@@ -17,7 +17,7 @@ CONFIG_PREEMPT=y
 CONFIG_AEABI=y
 CONFIG_ZBOOT_ROM_TEXT=0x0
 CONFIG_ZBOOT_ROM_BSS=0x0
-CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M"
+CONFIG_CMDLINE="root=/dev/nfs rootfstype=nfs nfsroot=192.168.2.100:/nfsroot/ ip=192.168.2.101:192.168.2.100::255.255.255.0::eth0:on console=ttyS0,115200 mem=128M earlyprintk"
 CONFIG_FPE_NWFPE=y
 CONFIG_NET=y
 CONFIG_PACKET=y
@@ -66,5 +66,7 @@ CONFIG_DEBUG_INFO=y
 CONFIG_DEBUG_USER=y
 CONFIG_DEBUG_ERRORS=y
 CONFIG_DEBUG_LL=y
+CONFIG_DEBUG_MMP_UART2=y
+CONFIG_EARLY_PRINTK=y
 # CONFIG_CRYPTO_ANSI_CPRNG is not set
 CONFIG_CRC_CCITT=y

arch/arm/mach-exynos/Kconfig

@@ -221,6 +221,7 @@ config MACH_SMDKV310
 	select EXYNOS4_SETUP_KEYPAD
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for Samsung SMDKV310
 
@@ -348,6 +349,7 @@ config MACH_ORIGEN
 	select EXYNOS4_SETUP_FIMD0
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for ORIGEN based on Samsung EXYNOS4210
 
@@ -383,6 +385,7 @@ config MACH_SMDK4212
 	select EXYNOS4_SETUP_KEYPAD
 	select EXYNOS4_SETUP_SDHCI
 	select EXYNOS4_SETUP_USB_PHY
+	select S3C24XX_PWM
 	help
 	  Machine support for Samsung SMDK4212
 

arch/arm/mach-exynos/mach-origen.c

@@ -15,6 +15,7 @@
 #include <linux/platform_device.h>
 #include <linux/io.h>
 #include <linux/input.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/gpio_keys.h>
 #include <linux/i2c.h>
@@ -614,6 +615,10 @@ static struct platform_device origen_lcd_hv070wsa = {
 	.dev.platform_data	= &origen_lcd_hv070wsa_data,
 };
 
+static struct pwm_lookup origen_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.0", 0, "pwm-backlight.0", NULL),
+};
+
 #ifdef CONFIG_DRM_EXYNOS
 static struct exynos_drm_fimd_pdata drm_fimd_pdata = {
 	.panel	= {
@@ -798,6 +803,7 @@ static void __init origen_machine_init(void)
 
 	platform_add_devices(origen_devices, ARRAY_SIZE(origen_devices));
 
+	pwm_add_table(origen_pwm_lookup, ARRAY_SIZE(origen_pwm_lookup));
 	samsung_bl_set(&origen_bl_gpio_info, &origen_bl_data);
 
 	origen_bt_setup();

arch/arm/mach-exynos/mach-smdk4x12.c

@@ -17,6 +17,7 @@
 #include <linux/mfd/max8997.h>
 #include <linux/mmc/host.h>
 #include <linux/platform_device.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/regulator/machine.h>
 #include <linux/serial_core.h>
@@ -222,6 +223,10 @@ static struct platform_pwm_backlight_data smdk4x12_bl_data = {
 	.pwm_period_ns  = 1000,
 };
 
+static struct pwm_lookup smdk4x12_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL),
+};
+
 static uint32_t smdk4x12_keymap[] __initdata = {
 	/* KEY(row, col, keycode) */
 	KEY(1, 3, KEY_1), KEY(1, 4, KEY_2), KEY(1, 5, KEY_3),
@@ -349,6 +354,7 @@ static void __init smdk4x12_machine_init(void)
 				ARRAY_SIZE(smdk4x12_i2c_devs7));
 
 	samsung_bl_set(&smdk4x12_bl_gpio_info, &smdk4x12_bl_data);
+	pwm_add_table(smdk4x12_pwm_lookup, ARRAY_SIZE(smdk4x12_pwm_lookup));
 
 	samsung_keypad_set_platdata(&smdk4x12_keypad_data);
 

arch/arm/mach-exynos/mach-smdkv310.c

@@ -18,6 +18,7 @@
 #include <linux/io.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
+#include <linux/pwm.h>
 #include <linux/pwm_backlight.h>
 #include <linux/platform_data/s3c-hsotg.h>
 
@@ -360,6 +361,10 @@ static struct i2c_board_info hdmiphy_info = {
 	I2C_BOARD_INFO("hdmiphy-exynos4210", 0x38),
 };
 
+static struct pwm_lookup smdkv310_pwm_lookup[] = {
+	PWM_LOOKUP("s3c24xx-pwm.1", 0, "pwm-backlight.0", NULL),
+};
+
 static void s5p_tv_setup(void)
 {
 	/* direct HPD to HDMI chip */
@@ -399,6 +404,8 @@ static void __init smdkv310_machine_init(void)
 	samsung_keypad_set_platdata(&smdkv310_keypad_data);
 
 	samsung_bl_set(&smdkv310_bl_gpio_info, &smdkv310_bl_data);
+	pwm_add_table(smdkv310_pwm_lookup, ARRAY_SIZE(smdkv310_pwm_lookup));
+
 #ifdef CONFIG_DRM_EXYNOS
 	s5p_device_fimd0.dev.platform_data = &drm_fimd_pdata;
 	exynos4_fimd0_gpio_setup_24bpp();

arch/arm/mach-imx/Kconfig

@@ -298,6 +298,7 @@ config MACH_MX27_3DS
 	select IMX_HAVE_PLATFORM_IMX_FB
 	select IMX_HAVE_PLATFORM_IMX_I2C
 	select IMX_HAVE_PLATFORM_IMX_KEYPAD
+	select IMX_HAVE_PLATFORM_IMX_SSI
 	select IMX_HAVE_PLATFORM_IMX_UART
 	select IMX_HAVE_PLATFORM_MX2_CAMERA
 	select IMX_HAVE_PLATFORM_MXC_EHCI

arch/arm/mach-imx/mach-mx27_3ds.c

@@ -158,6 +158,11 @@ static const int mx27pdk_pins[] __initconst = {
 	PB21_PF_CSI_HSYNC,
 	CSI_PWRDWN | GPIO_GPIO | GPIO_OUT,
 	CSI_RESET | GPIO_GPIO | GPIO_OUT,
+	/* SSI4 */
+	PC16_PF_SSI4_FS,
+	PC17_PF_SSI4_RXD,
+	PC18_PF_SSI4_TXD,
+	PC19_PF_SSI4_CLK,
 };
 
 static struct gpio mx27_3ds_camera_gpios[] = {
@@ -329,13 +334,24 @@ static struct mc13xxx_regulator_init_data mx27_3ds_regulators[] = {
 };
 
 /* MC13783 */
+static struct mc13xxx_codec_platform_data mx27_3ds_codec = {
+	.dac_ssi_port = MC13783_SSI1_PORT,
+	.adc_ssi_port = MC13783_SSI1_PORT,
+};
+
 static struct mc13xxx_platform_data mc13783_pdata = {
 	.regulators = {
 		.regulators = mx27_3ds_regulators,
 		.num_regulators = ARRAY_SIZE(mx27_3ds_regulators),
 
 	},
-	.flags  = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC,
+	.flags  = MC13XXX_USE_TOUCHSCREEN | MC13XXX_USE_RTC |
+						MC13XXX_USE_CODEC,
+	.codec = &mx27_3ds_codec,
+};
+
+static struct imx_ssi_platform_data mx27_3ds_ssi_pdata = {
+	.flags = IMX_SSI_DMA | IMX_SSI_NET,
 };
 
 /* SPI */
@@ -512,6 +528,9 @@ static void __init mx27pdk_init(void)
 	}
 
 	imx27_add_mx2_camera(&mx27_3ds_cam_pdata);
+	imx27_add_imx_ssi(0, &mx27_3ds_ssi_pdata);
+
+	imx_add_platform_device("imx_mc13783", 0, NULL, 0, NULL, 0);
 }
 
 static void __init mx27pdk_timer_init(void)

arch/arm/mach-ks8695/Kconfig

@@ -21,6 +21,67 @@ config MACH_ACS5K
 	  say 'Y' here if you want your kernel to run on the Brivo
 	  Systems LLC, ACS-5000 Master board.
 
+config MACH_LITE300
+	bool "SecureComputing SG300"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  SecureComputing / SnapGear SG300 VPN Internet Router.
+	  See http://www.securecomputing.com for more details.
+
+config MACH_SG310
+	bool "McAfee SG310"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  McAfee / SnapGear SG310 VPN Internet Router.
+	  See http://www.mcafee.com for more details.
+
+config MACH_SE4200
+	bool "SecureComputing SE4200"
+	help
+	  Say 'Y' here if you want your kernel to support the
+	  SecureComputing / SnapGear SE4200 Secure Wireless VPN
+	  Internet Router.
+	  See http://www.securecomputing.com for more details.
+
+config MACH_CM4002
+	bool "OpenGear CM4002"
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4002 Secure Access Server. See http://www.opengear.com for
+	  more details.
+
+config MACH_CM4008
+	bool "OpenGear CM4008"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4008 Console Server. See http://www.opengear.com for more
+	  details.
+
+config MACH_CM41xx
+	bool "OpenGear CM41xx"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  CM4016 or CM4048 Console Servers. See http://www.opengear.com for
+	  more details.
+
+config MACH_IM4004
+	bool "OpenGear IM4004"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  IM4004 Secure Access Server. See http://www.opengear.com for
+	  more details.
+
+config MACH_IM42xx
+	bool "OpenGear IM42xx"
+	select MIGHT_HAVE_PCI
+	help
+	  Say 'Y' here if you want your kernel to support the OpenGear
+	  IM4216 or IM4248 Console Servers. See http://www.opengear.com for
+	  more details.
+
 endmenu
 
 endif

arch/arm/mach-ks8695/Makefile

@@ -15,3 +15,11 @@ obj-$(CONFIG_PCI)		+= pci.o
 obj-$(CONFIG_MACH_KS8695)	+= board-micrel.o
 obj-$(CONFIG_MACH_DSM320)	+= board-dsm320.o
 obj-$(CONFIG_MACH_ACS5K)	+= board-acs5k.o
+obj-$(CONFIG_MACH_LITE300)	+= board-sg.o
+obj-$(CONFIG_MACH_SG310)	+= board-sg.o
+obj-$(CONFIG_MACH_SE4200)	+= board-sg.o
+obj-$(CONFIG_MACH_CM4002)	+= board-og.o
+obj-$(CONFIG_MACH_CM4008)	+= board-og.o
+obj-$(CONFIG_MACH_CM41xx)	+= board-og.o
+obj-$(CONFIG_MACH_IM4004)	+= board-og.o
+obj-$(CONFIG_MACH_IM42xx)	+= board-og.o

arch/arm/mach-ks8695/board-og.c

+/*
+ * board-og.c -- support for the OpenGear KS8695 based boards.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/delay.h>
+#include <linux/platform_device.h>
+#include <linux/serial_8250.h>
+#include <linux/gpio.h>
+#include <linux/irq.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <mach/devices.h>
+#include <mach/regs-gpio.h>
+#include <mach/gpio-ks8695.h>
+#include "generic.h"
+
+static int og_pci_map_irq(const struct pci_dev *dev, u8 slot, u8 pin)
+{
+	if (machine_is_im4004() && (slot == 8))
+		return KS8695_IRQ_EXTERN1;
+	return KS8695_IRQ_EXTERN0;
+}
+
+static struct ks8695_pci_cfg __initdata og_pci = {
+	.mode		= KS8695_MODE_PCI,
+	.map_irq	= og_pci_map_irq,
+};
+
+static void __init og_register_pci(void)
+{
+	/* Initialize the GPIO lines for interrupt mode */
+	ks8695_gpio_interrupt(KS8695_GPIO_0, IRQ_TYPE_LEVEL_LOW);
+
+	/* Cardbus Slot */
+	if (machine_is_im4004())
+		ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_LOW);
+
+	ks8695_init_pci(&og_pci);
+}
+
+/*
+ * The PCI bus reset is driven by a dedicated GPIO line. Toggle it here
+ * and bring the PCI bus out of reset.
+ */
+static void __init og_pci_bus_reset(void)
+{
+	unsigned int rstline = 1;
+
+	/* Some boards use a different GPIO as the PCI reset line */
+	if (machine_is_im4004())
+		rstline = 2;
+	else if (machine_is_im42xx())
+		rstline = 0;
+
+	gpio_request(rstline, "PCI reset");
+	gpio_direction_output(rstline, 0);
+
+	/* Drive a reset on the PCI reset line */
+	gpio_set_value(rstline, 1);
+	gpio_set_value(rstline, 0);
+	mdelay(100);
+	gpio_set_value(rstline, 1);
+	mdelay(100);
+}
+
+/*
+ * Direct connect serial ports (non-PCI that is).
+ */
+#define	S8250_PHYS	0x03800000
+#define	S8250_VIRT	0xf4000000
+#define	S8250_SIZE	0x00100000
+
+static struct __initdata map_desc og_io_desc[] = {
+	{
+		.virtual	= S8250_VIRT,
+		.pfn		= __phys_to_pfn(S8250_PHYS),
+		.length		= S8250_SIZE,
+		.type		= MT_DEVICE,
+	}
+};
+
+static struct resource og_uart_resources[] = {
+	{
+		.start		= S8250_VIRT,
+		.end		= S8250_VIRT + S8250_SIZE,
+		.flags		= IORESOURCE_MEM
+	},
+};
+
+static struct plat_serial8250_port og_uart_data[] = {
+	{
+		.mapbase	= S8250_VIRT,
+		.membase	= (char *) S8250_VIRT,
+		.irq		= 3,
+		.flags		= UPF_BOOT_AUTOCONF | UPF_SKIP_TEST,
+		.iotype		= UPIO_MEM,
+		.regshift	= 2,
+		.uartclk	= 115200 * 16,
+	},
+	{ },
+};
+
+static struct platform_device og_uart = {
+	.name			= "serial8250",
+	.id			= 0,
+	.dev.platform_data	= og_uart_data,
+	.num_resources		= 1,
+	.resource		= og_uart_resources
+};
+
+static struct platform_device *og_devices[] __initdata = {
+	&og_uart
+};
+
+static void __init og_init(void)
+{
+	ks8695_register_gpios();
+
+	if (machine_is_cm4002()) {
+		ks8695_gpio_interrupt(KS8695_GPIO_1, IRQ_TYPE_LEVEL_HIGH);
+		iotable_init(og_io_desc, ARRAY_SIZE(og_io_desc));
+		platform_add_devices(og_devices, ARRAY_SIZE(og_devices));
+	} else {
+		og_pci_bus_reset();
+		og_register_pci();
+	}
+
+	ks8695_add_device_lan();
+	ks8695_add_device_wan();
+}
+
+#ifdef CONFIG_MACH_CM4002
+MACHINE_START(CM4002, "OpenGear/CM4002")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_CM4008
+MACHINE_START(CM4008, "OpenGear/CM4008")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_CM41xx
+MACHINE_START(CM41XX, "OpenGear/CM41xx")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_IM4004
+MACHINE_START(IM4004, "OpenGear/IM4004")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_IM42xx
+MACHINE_START(IM42XX, "OpenGear/IM42xx")
+	/* OpenGear Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= og_init,
+	.timer		= &ks8695_timer,
+	.restart        = ks8695_restart,
+MACHINE_END
+#endif

arch/arm/mach-ks8695/board-sg.c

+/*
+ * board-sg.c -- support for the SnapGear KS8695 based boards
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/map.h>
+#include <linux/mtd/physmap.h>
+#include <linux/mtd/partitions.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/devices.h>
+#include "generic.h"
+
+/*
+ * The SG310 machine type is fitted with a conventional 8MB Strataflash
+ * device. Define its partitioning.
+ */
+#define	FL_BASE		0x02000000
+#define	FL_SIZE		SZ_8M
+
+static struct mtd_partition sg_mtd_partitions[] = {
+	[0] = {
+		.name	= "SnapGear Boot Loader",
+		.size	= SZ_128K,
+	},
+	[1] = {
+		.name	= "SnapGear non-volatile configuration",
+		.size	= SZ_512K,
+		.offset	= SZ_256K,
+	},
+	[2] = {
+		.name	= "SnapGear image",
+		.offset	= SZ_512K + SZ_256K,
+	},
+	[3] = {
+		.name	= "SnapGear StrataFlash",
+	},
+	[4] = {
+		.name	= "SnapGear Boot Tags",
+		.size	= SZ_128K,
+		.offset	= SZ_128K,
+	},
+};
+
+static struct physmap_flash_data sg_mtd_pdata = {
+	.width		= 1,
+	.nr_parts	= ARRAY_SIZE(sg_mtd_partitions),
+	.parts		= sg_mtd_partitions,
+};
+
+
+static struct resource sg_mtd_resource[] = {
+	[0] = {
+		.start = FL_BASE,
+		.end   = FL_BASE + FL_SIZE - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device sg_mtd_device = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.num_resources	= ARRAY_SIZE(sg_mtd_resource),
+	.resource	= sg_mtd_resource,
+	.dev		= {
+		.platform_data = &sg_mtd_pdata,
+	},
+};
+
+static void __init sg_init(void)
+{
+	ks8695_add_device_lan();
+	ks8695_add_device_wan();
+
+	if (machine_is_sg310())
+		platform_device_register(&sg_mtd_device);
+}
+
+#ifdef CONFIG_MACH_LITE300
+MACHINE_START(LITE300, "SecureComputing/SG300")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_SG310
+MACHINE_START(SG310, "McAfee/SG310")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif
+
+#ifdef CONFIG_MACH_SE4200
+MACHINE_START(SE4200, "SecureComputing/SE4200")
+	/* SnapGear */
+	.atag_offset	= 0x100,
+	.map_io		= ks8695_map_io,
+	.init_irq	= ks8695_init_irq,
+	.init_machine	= sg_init,
+	.timer		= &ks8695_timer,
+	.restart	= ks8695_restart,
+MACHINE_END
+#endif

arch/arm/mach-mmp/include/mach/debug-macro.S

@@ -9,13 +9,21 @@
  * published by the Free Software Foundation.
  */
 
+#if defined(CONFIG_DEBUG_MMP_UART2)
+#define MMP_UART_OFFSET	0x00017000
+#elif defined(CONFIG_DEBUG_MMP_UART3)
+#define MMP_UART_OFFSET	0x00018000
+#else
+#error "Select uart for DEBUG_LL"
+#endif
+
 #include <mach/addr-map.h>
 
 		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =APB_PHYS_BASE		@ physical
 		ldr	\rv, =APB_VIRT_BASE		@ virtual
-		orr	\rp, \rp, #0x00017000
-		orr	\rv, \rv, #0x00017000
+		orr	\rp, \rp, #MMP_UART_OFFSET
+		orr	\rv, \rv, #MMP_UART_OFFSET
 		.endm
 
 #define UART_SHIFT	2

arch/arm/mach-mmp/ttc_dkb.c

@@ -177,12 +177,22 @@ static struct mv_usb_platform_data ttc_usb_pdata = {
 #endif
 #endif
 
+#ifdef CONFIG_MTD_NAND_PXA3xx
+static struct pxa3xx_nand_platform_data dkb_nand_info = {
+	.enable_arbiter = 1,
+	.num_cs = 1,
+};
+#endif
+
 static void __init ttc_dkb_init(void)
 {
 	mfp_config(ARRAY_AND_SIZE(ttc_dkb_pin_config));
 
 	/* on-chip devices */
 	pxa910_add_uart(1);
+#ifdef CONFIG_MTD_NAND_PXA3xx
+	pxa910_add_nand(&dkb_nand_info);
+#endif
 
 	/* off-chip devices */
 	pxa910_add_twsi(0, NULL, ARRAY_AND_SIZE(ttc_dkb_i2c_info));

arch/arm/mach-msm/Kconfig

 if ARCH_MSM
 
+comment "Qualcomm MSM SoC Type"
+	depends on (ARCH_MSM8X60 || ARCH_MSM8960)
+
 choice
 	prompt "Qualcomm MSM SoC Type"
 	default ARCH_MSM7X00A
+	depends on !(ARCH_MSM8X60 || ARCH_MSM8960)
 
 config ARCH_MSM7X00A
 	bool "MSM7x00A / MSM7x01A"
@@ -36,6 +40,8 @@ config ARCH_QSD8X50
 	select GPIO_MSM_V1
 	select MSM_PROC_COMM
 
+endchoice
+
 config ARCH_MSM8X60
 	bool "MSM8X60"
 	select ARCH_MSM_SCORPIONMP
@@ -57,8 +63,6 @@ config ARCH_MSM8960
 	select MSM_SCM if SMP
 	select USE_OF
 
-endchoice
-
 config MSM_HAS_DEBUG_UART_HS
 	bool
 

arch/arm/mach-msm/include/mach/msm_iomap-8x60.h

@@ -41,21 +41,10 @@
 #define MSM8X60_QGIC_CPU_PHYS	0x02081000
 #define MSM8X60_QGIC_CPU_SIZE	SZ_4K
 
-#define MSM_ACC_BASE		IOMEM(0xF0002000)
-#define MSM_ACC_PHYS		0x02001000
-#define MSM_ACC_SIZE		SZ_4K
-
-#define MSM_GCC_BASE		IOMEM(0xF0003000)
-#define MSM_GCC_PHYS		0x02082000
-#define MSM_GCC_SIZE		SZ_4K
-
 #define MSM_TLMM_BASE		IOMEM(0xF0004000)
 #define MSM_TLMM_PHYS		0x00800000
 #define MSM_TLMM_SIZE		SZ_16K
 
-#define MSM_SHARED_RAM_BASE	IOMEM(0xF0100000)
-#define MSM_SHARED_RAM_SIZE	SZ_1M
-
 #define MSM8X60_TMR_PHYS	0x02000000
 #define MSM8X60_TMR_SIZE	SZ_4K
 

arch/arm/mach-msm/include/mach/msm_iomap.h

@@ -41,12 +41,11 @@
 #include "msm_iomap-7x30.h"
 #elif defined(CONFIG_ARCH_QSD8X50)
 #include "msm_iomap-8x50.h"
-#elif defined(CONFIG_ARCH_MSM8X60)
-#include "msm_iomap-8x60.h"
 #else
 #include "msm_iomap-7x00.h"
 #endif
 
+#include "msm_iomap-8x60.h"
 #include "msm_iomap-8960.h"
 
 #define MSM_DEBUG_UART_SIZE	SZ_4K

arch/arm/mach-msm/io.c

@@ -111,8 +111,6 @@ static struct map_desc msm8x60_io_desc[] __initdata = {
 	MSM_CHIP_DEVICE(QGIC_CPU, MSM8X60),
 	MSM_CHIP_DEVICE(TMR, MSM8X60),
 	MSM_CHIP_DEVICE(TMR0, MSM8X60),
-	MSM_DEVICE(ACC),
-	MSM_DEVICE(GCC),
 #ifdef CONFIG_DEBUG_MSM8660_UART
 	MSM_DEVICE(DEBUG_UART),
 #endif

arch/arm/mach-s3c64xx/mach-crag6410-module.c

@@ -16,6 +16,7 @@
 #include <linux/mfd/wm831x/irq.h>
 #include <linux/mfd/wm831x/gpio.h>
 #include <linux/mfd/wm8994/pdata.h>
+#include <linux/mfd/arizona/pdata.h>
 
 #include <linux/regulator/machine.h>
 
@@ -181,9 +182,33 @@ static const struct i2c_board_info wm1277_devs[] = {
 	},
 };
 
-static const struct i2c_board_info wm5102_devs[] = {
-	{ I2C_BOARD_INFO("wm5102", 0x1a),
-	  .irq = GLENFARCLAS_PMIC_IRQ_BASE + WM831X_IRQ_GPIO_2, },
+static struct arizona_pdata wm5102_pdata = {
+	.ldoena = S3C64XX_GPN(7),
+	.gpio_base = CODEC_GPIO_BASE,
+	.irq_active_high = true,
+	.micd_pol_gpio = CODEC_GPIO_BASE + 4,
+	.gpio_defaults = {
+		[2] = 0x10000, /* AIF3TXLRCLK */
+		[3] = 0x4,     /* OPCLK */
+	},
+};
+
+static struct s3c64xx_spi_csinfo wm5102_spi_csinfo = {
+	.line = S3C64XX_GPN(5),
+};
+
+static struct spi_board_info wm5102_spi_devs[] = {
+	[0] = {
+		.modalias	= "wm5102",
+		.max_speed_hz	= 10 * 1000 * 1000,
+		.bus_num	= 0,
+		.chip_select	= 0,
+		.mode		= SPI_MODE_0,
+		.irq		= GLENFARCLAS_PMIC_IRQ_BASE +
+				  WM831X_IRQ_GPIO_2,
+		.controller_data = &wm5102_spi_csinfo,
+		.platform_data = &wm5102_pdata,
+	},
 };
 
 static const struct i2c_board_info wm6230_i2c_devs[] = {
@@ -223,8 +248,9 @@ static __devinitdata const struct {
 	{ .id = 0x3c, .name = "1273-EV1 Longmorn" },
 	{ .id = 0x3d, .name = "1277-EV1 Littlemill",
 	  .i2c_devs = wm1277_devs, .num_i2c_devs = ARRAY_SIZE(wm1277_devs) },
-	{ .id = 0x3e, .name = "WM5102-6271-EV1-CS127",
-	  .i2c_devs = wm5102_devs, .num_i2c_devs = ARRAY_SIZE(wm5102_devs) },
+	{ .id = 0x3e, .name = "WM5102-6271-EV1-CS127 Amrut",
+	  .spi_devs = wm5102_spi_devs,
+	  .num_spi_devs = ARRAY_SIZE(wm5102_spi_devs) },
 };
 
 static __devinit int wlf_gf_module_probe(struct i2c_client *i2c,

arch/arm/mach-s3c64xx/mach-crag6410.c

@@ -287,6 +287,16 @@ static struct platform_device littlemill_device = {
 	.id		= -1,
 };
 
+static struct platform_device bells_wm5102_device = {
+	.name		= "bells",
+	.id		= 0,
+};
+
+static struct platform_device bells_wm5110_device = {
+	.name		= "bells",
+	.id		= 1,
+};
+
 static struct regulator_consumer_supply wallvdd_consumers[] = {
 	REGULATOR_SUPPLY("SPKVDD", "1-001a"),
 	REGULATOR_SUPPLY("SPKVDD1", "1-001a"),
@@ -359,6 +369,8 @@ static struct platform_device *crag6410_devices[] __initdata = {
 	&tobermory_device,
 	&littlemill_device,
 	&lowland_device,
+	&bells_wm5102_device,
+	&bells_wm5110_device,
 	&wallvdd_device,
 };
 

arch/arm/mach-shmobile/board-armadillo800eva.c

@@ -37,6 +37,7 @@
 #include <linux/mmc/host.h>
 #include <linux/mmc/sh_mmcif.h>
 #include <linux/mmc/sh_mobile_sdhi.h>
+#include <linux/i2c-gpio.h>
 #include <mach/common.h>
 #include <mach/irqs.h>
 #include <mach/r8a7740.h>
@@ -877,6 +878,21 @@ static struct platform_device fsi_hdmi_device = {
 	},
 };
 
+/* RTC: RTC connects i2c-gpio. */
+static struct i2c_gpio_platform_data i2c_gpio_data = {
+	.sda_pin	= GPIO_PORT208,
+	.scl_pin	= GPIO_PORT91,
+	.udelay		= 5, /* 100 kHz */
+};
+
+static struct platform_device i2c_gpio_device = {
+	.name = "i2c-gpio",
+	.id = 2,
+	.dev = {
+		.platform_data = &i2c_gpio_data,
+	},
+};
+
 /* I2C */
 static struct i2c_board_info i2c0_devices[] = {
 	{
@@ -888,6 +904,13 @@ static struct i2c_board_info i2c0_devices[] = {
 	},
 };
 
+static struct i2c_board_info i2c2_devices[] = {
+	{
+		I2C_BOARD_INFO("s35390a", 0x30),
+		.type = "s35390a",
+	},
+};
+
 /*
  * board devices
  */
@@ -904,6 +927,7 @@ static struct platform_device *eva_devices[] __initdata = {
 	&fsi_device,
 	&fsi_wm8978_device,
 	&fsi_hdmi_device,
+	&i2c_gpio_device,
 };
 
 static void __init eva_clock_init(void)
@@ -1174,6 +1198,7 @@ static void __init eva_init(void)
 #endif
 
 	i2c_register_board_info(0, i2c0_devices, ARRAY_SIZE(i2c0_devices));
+	i2c_register_board_info(2, i2c2_devices, ARRAY_SIZE(i2c2_devices));
 
 	r8a7740_add_standard_devices();
 

arch/arm/mach-shmobile/board-marzen.c

@@ -30,6 +30,8 @@
 #include <linux/regulator/fixed.h>
 #include <linux/regulator/machine.h>
 #include <linux/smsc911x.h>
+#include <linux/mmc/sh_mobile_sdhi.h>
+#include <linux/mfd/tmio.h>
 #include <mach/hardware.h>
 #include <mach/r8a7779.h>
 #include <mach/common.h>
@@ -39,6 +41,12 @@
 #include <asm/hardware/gic.h>
 #include <asm/traps.h>
 
+/* Fixed 3.3V regulator to be used by SDHI0 */
+static struct regulator_consumer_supply fixed3v3_power_consumers[] = {
+	REGULATOR_SUPPLY("vmmc", "sh_mobile_sdhi.0"),
+	REGULATOR_SUPPLY("vqmmc", "sh_mobile_sdhi.0"),
+};
+
 /* Dummy supplies, where voltage doesn't matter */
 static struct regulator_consumer_supply dummy_supplies[] = {
 	REGULATOR_SUPPLY("vddvario", "smsc911x"),
@@ -75,13 +83,61 @@ static struct platform_device eth_device = {
 	.num_resources	= ARRAY_SIZE(smsc911x_resources),
 };
 
+static struct resource sdhi0_resources[] = {
+	[0] = {
+		.name	= "sdhi0",
+		.start	= 0xffe4c000,
+		.end	= 0xffe4c0ff,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= gic_spi(104),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct sh_mobile_sdhi_info sdhi0_platform_data = {
+	.tmio_flags = TMIO_MMC_WRPROTECT_DISABLE | TMIO_MMC_HAS_IDLE_WAIT,
+	.tmio_caps = MMC_CAP_SD_HIGHSPEED,
+};
+
+static struct platform_device sdhi0_device = {
+	.name = "sh_mobile_sdhi",
+	.num_resources = ARRAY_SIZE(sdhi0_resources),
+	.resource = sdhi0_resources,
+	.id = 0,
+	.dev = {
+		.platform_data = &sdhi0_platform_data,
+	}
+};
+
+/* Thermal */
+static struct resource thermal_resources[] = {
+	[0] = {
+		.start		= 0xFFC48000,
+		.end		= 0xFFC48038 - 1,
+		.flags		= IORESOURCE_MEM,
+	},
+};
+
+static struct platform_device thermal_device = {
+	.name		= "rcar_thermal",
+	.resource	= thermal_resources,
+	.num_resources	= ARRAY_SIZE(thermal_resources),
+};
+
 static struct platform_device *marzen_devices[] __initdata = {
 	&eth_device,
+	&sdhi0_device,
+	&thermal_device,
 };
 
 static void __init marzen_init(void)
 {
-	regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
+	regulator_register_always_on(0, "fixed-3.3V", fixed3v3_power_consumers,
+				ARRAY_SIZE(fixed3v3_power_consumers), 3300000);
+	regulator_register_fixed(1, dummy_supplies,
+				ARRAY_SIZE(dummy_supplies));
 
 	r8a7779_pinmux_init();
 
@@ -97,6 +153,16 @@ static void __init marzen_init(void)
 	gpio_request(GPIO_FN_EX_CS0, NULL); /* nCS */
 	gpio_request(GPIO_FN_IRQ1_B, NULL); /* IRQ + PME */
 
+	/* SD0 (CN20) */
+	gpio_request(GPIO_FN_SD0_CLK, NULL);
+	gpio_request(GPIO_FN_SD0_CMD, NULL);
+	gpio_request(GPIO_FN_SD0_DAT0, NULL);
+	gpio_request(GPIO_FN_SD0_DAT1, NULL);
+	gpio_request(GPIO_FN_SD0_DAT2, NULL);
+	gpio_request(GPIO_FN_SD0_DAT3, NULL);
+	gpio_request(GPIO_FN_SD0_CD, NULL);
+	gpio_request(GPIO_FN_SD0_WP, NULL);
+
 	r8a7779_add_standard_devices();
 	platform_add_devices(marzen_devices, ARRAY_SIZE(marzen_devices));
 }