Merge remote-tracking branch 'asoc/topic/wm8962' into asoc-next

sound/soc/codecs/wm8962.c

@@ -3242,7 +3242,7 @@ static void wm8962_free_beep(struct snd_soc_codec *codec)
 }
 #endif
 
-static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio)
+static void wm8962_set_gpio_mode(struct wm8962_priv *wm8962, int gpio)
 {
 	int mask = 0;
 	int val = 0;
@@ -3263,8 +3263,8 @@ static void wm8962_set_gpio_mode(struct snd_soc_codec *codec, int gpio)
 	}
 
 	if (mask)
-		snd_soc_update_bits(codec, WM8962_ANALOGUE_CLOCKING1,
-				    mask, val);
+		regmap_update_bits(wm8962->regmap, WM8962_ANALOGUE_CLOCKING1,
+				   mask, val);
 }
 
 #ifdef CONFIG_GPIOLIB
@@ -3276,7 +3276,6 @@ static inline struct wm8962_priv *gpio_to_wm8962(struct gpio_chip *chip)
 static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset)
 {
 	struct wm8962_priv *wm8962 = gpio_to_wm8962(chip);
-	struct snd_soc_codec *codec = wm8962->codec;
 
 	/* The WM8962 GPIOs aren't linearly numbered.  For simplicity
 	 * we export linear numbers and error out if the unsupported
@@ -3292,7 +3291,7 @@ static int wm8962_gpio_request(struct gpio_chip *chip, unsigned offset)
 		return -EINVAL;
 	}
 
-	wm8962_set_gpio_mode(codec, offset + 1);
+	wm8962_set_gpio_mode(wm8962, offset + 1);
 
 	return 0;
 }
@@ -3376,8 +3375,7 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 {
 	int ret;
 	struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
-	struct wm8962_pdata *pdata = &wm8962->pdata;
-	int i, trigger, irq_pol;
+	int i;
 	bool dmicclk, dmicdat;
 
 	wm8962->codec = codec;
@@ -3409,75 +3407,6 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 		}
 	}
 
-	/* SYSCLK defaults to on; make sure it is off so we can safely
-	 * write to registers if the device is declocked.
-	 */
-	snd_soc_update_bits(codec, WM8962_CLOCKING2, WM8962_SYSCLK_ENA, 0);
-
-	/* Ensure we have soft control over all registers */
-	snd_soc_update_bits(codec, WM8962_CLOCKING2,
-			    WM8962_CLKREG_OVD, WM8962_CLKREG_OVD);
-
-	/* Ensure that the oscillator and PLLs are disabled */
-	snd_soc_update_bits(codec, WM8962_PLL2,
-			    WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
-			    0);
-
-	/* Apply static configuration for GPIOs */
-	for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++)
-		if (pdata->gpio_init[i]) {
-			wm8962_set_gpio_mode(codec, i + 1);
-			snd_soc_write(codec, 0x200 + i,
-					pdata->gpio_init[i] & 0xffff);
-		}
-
-
-	/* Put the speakers into mono mode? */
-	if (pdata->spk_mono)
-		snd_soc_update_bits(codec, WM8962_CLASS_D_CONTROL_2,
-				WM8962_SPK_MONO_MASK, WM8962_SPK_MONO);
-
-	/* Micbias setup, detection enable and detection
-	 * threasholds. */
-	if (pdata->mic_cfg)
-		snd_soc_update_bits(codec, WM8962_ADDITIONAL_CONTROL_4,
-				    WM8962_MICDET_ENA |
-				    WM8962_MICDET_THR_MASK |
-				    WM8962_MICSHORT_THR_MASK |
-				    WM8962_MICBIAS_LVL,
-				    pdata->mic_cfg);
-
-	/* Latch volume update bits */
-	snd_soc_update_bits(codec, WM8962_LEFT_INPUT_VOLUME,
-			    WM8962_IN_VU, WM8962_IN_VU);
-	snd_soc_update_bits(codec, WM8962_RIGHT_INPUT_VOLUME,
-			    WM8962_IN_VU, WM8962_IN_VU);
-	snd_soc_update_bits(codec, WM8962_LEFT_ADC_VOLUME,
-			    WM8962_ADC_VU, WM8962_ADC_VU);
-	snd_soc_update_bits(codec, WM8962_RIGHT_ADC_VOLUME,
-			    WM8962_ADC_VU, WM8962_ADC_VU);
-	snd_soc_update_bits(codec, WM8962_LEFT_DAC_VOLUME,
-			    WM8962_DAC_VU, WM8962_DAC_VU);
-	snd_soc_update_bits(codec, WM8962_RIGHT_DAC_VOLUME,
-			    WM8962_DAC_VU, WM8962_DAC_VU);
-	snd_soc_update_bits(codec, WM8962_SPKOUTL_VOLUME,
-			    WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
-	snd_soc_update_bits(codec, WM8962_SPKOUTR_VOLUME,
-			    WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
-	snd_soc_update_bits(codec, WM8962_HPOUTL_VOLUME,
-			    WM8962_HPOUT_VU, WM8962_HPOUT_VU);
-	snd_soc_update_bits(codec, WM8962_HPOUTR_VOLUME,
-			    WM8962_HPOUT_VU, WM8962_HPOUT_VU);
-
-	/* Stereo control for EQ */
-	snd_soc_update_bits(codec, WM8962_EQ1, WM8962_EQ_SHARED_COEFF, 0);
-
-	/* Don't debouce interrupts so we don't need SYSCLK */
-	snd_soc_update_bits(codec, WM8962_IRQ_DEBOUNCE,
-			    WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB |
-			    WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB,
-			    0);
-
 	wm8962_add_widgets(codec);
 
 	/* Save boards having to disable DMIC when not in use */
@@ -3506,36 +3435,6 @@ static int wm8962_probe(struct snd_soc_codec *codec)
 	wm8962_init_beep(codec);
 	wm8962_init_gpio(codec);
 
-	if (wm8962->irq) {
-		if (pdata->irq_active_low) {
-			trigger = IRQF_TRIGGER_LOW;
-			irq_pol = WM8962_IRQ_POL;
-		} else {
-			trigger = IRQF_TRIGGER_HIGH;
-			irq_pol = 0;
-		}
-
-		snd_soc_update_bits(codec, WM8962_INTERRUPT_CONTROL,
-				    WM8962_IRQ_POL, irq_pol);
-
-		ret = request_threaded_irq(wm8962->irq, NULL, wm8962_irq,
-					   trigger | IRQF_ONESHOT,
-					   "wm8962", codec->dev);
-		if (ret != 0) {
-			dev_err(codec->dev, "Failed to request IRQ %d: %d\n",
-				wm8962->irq, ret);
-			wm8962->irq = 0;
-			/* Non-fatal */
-		} else {
-			/* Enable some IRQs by default */
-			snd_soc_update_bits(codec,
-					    WM8962_INTERRUPT_STATUS_2_MASK,
-					    WM8962_FLL_LOCK_EINT |
-					    WM8962_TEMP_SHUT_EINT |
-					    WM8962_FIFOS_ERR_EINT, 0);
-		}
-	}
-
 	return 0;
 }
 
@@ -3544,9 +3443,6 @@ static int wm8962_remove(struct snd_soc_codec *codec)
 	struct wm8962_priv *wm8962 = snd_soc_codec_get_drvdata(codec);
 	int i;
 
-	if (wm8962->irq)
-		free_irq(wm8962->irq, codec);
-
 	cancel_delayed_work_sync(&wm8962->mic_work);
 
 	wm8962_free_gpio(codec);
@@ -3619,7 +3515,7 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 	struct wm8962_pdata *pdata = dev_get_platdata(&i2c->dev);
 	struct wm8962_priv *wm8962;
 	unsigned int reg;
-	int ret, i;
+	int ret, i, irq_pol, trigger;
 
 	wm8962 = devm_kzalloc(&i2c->dev, sizeof(struct wm8962_priv),
 			      GFP_KERNEL);
@@ -3704,6 +3600,77 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 		goto err_enable;
 	}
 
+	/* SYSCLK defaults to on; make sure it is off so we can safely
+	 * write to registers if the device is declocked.
+	 */
+	regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
+			   WM8962_SYSCLK_ENA, 0);
+
+	/* Ensure we have soft control over all registers */
+	regmap_update_bits(wm8962->regmap, WM8962_CLOCKING2,
+			   WM8962_CLKREG_OVD, WM8962_CLKREG_OVD);
+
+	/* Ensure that the oscillator and PLLs are disabled */
+	regmap_update_bits(wm8962->regmap, WM8962_PLL2,
+			   WM8962_OSC_ENA | WM8962_PLL2_ENA | WM8962_PLL3_ENA,
+			   0);
+
+	/* Apply static configuration for GPIOs */
+	for (i = 0; i < ARRAY_SIZE(pdata->gpio_init); i++)
+		if (pdata->gpio_init[i]) {
+			wm8962_set_gpio_mode(wm8962, i + 1);
+			regmap_write(wm8962->regmap, 0x200 + i,
+				     pdata->gpio_init[i] & 0xffff);
+		}
+
+
+	/* Put the speakers into mono mode? */
+	if (pdata->spk_mono)
+		regmap_update_bits(wm8962->regmap, WM8962_CLASS_D_CONTROL_2,
+				   WM8962_SPK_MONO_MASK, WM8962_SPK_MONO);
+
+	/* Micbias setup, detection enable and detection
+	 * threasholds. */
+	if (pdata->mic_cfg)
+		regmap_update_bits(wm8962->regmap, WM8962_ADDITIONAL_CONTROL_4,
+				   WM8962_MICDET_ENA |
+				   WM8962_MICDET_THR_MASK |
+				   WM8962_MICSHORT_THR_MASK |
+				   WM8962_MICBIAS_LVL,
+				   pdata->mic_cfg);
+
+	/* Latch volume update bits */
+	regmap_update_bits(wm8962->regmap, WM8962_LEFT_INPUT_VOLUME,
+			   WM8962_IN_VU, WM8962_IN_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_RIGHT_INPUT_VOLUME,
+			   WM8962_IN_VU, WM8962_IN_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_LEFT_ADC_VOLUME,
+			   WM8962_ADC_VU, WM8962_ADC_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_RIGHT_ADC_VOLUME,
+			   WM8962_ADC_VU, WM8962_ADC_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_LEFT_DAC_VOLUME,
+			   WM8962_DAC_VU, WM8962_DAC_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_RIGHT_DAC_VOLUME,
+			   WM8962_DAC_VU, WM8962_DAC_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_SPKOUTL_VOLUME,
+			   WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_SPKOUTR_VOLUME,
+			   WM8962_SPKOUT_VU, WM8962_SPKOUT_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_HPOUTL_VOLUME,
+			   WM8962_HPOUT_VU, WM8962_HPOUT_VU);
+	regmap_update_bits(wm8962->regmap, WM8962_HPOUTR_VOLUME,
+			   WM8962_HPOUT_VU, WM8962_HPOUT_VU);
+
+	/* Stereo control for EQ */
+	regmap_update_bits(wm8962->regmap, WM8962_EQ1,
+			   WM8962_EQ_SHARED_COEFF, 0);
+
+	/* Don't debouce interrupts so we don't need SYSCLK */
+	regmap_update_bits(wm8962->regmap, WM8962_IRQ_DEBOUNCE,
+			   WM8962_FLL_LOCK_DB | WM8962_PLL3_LOCK_DB |
+			   WM8962_PLL2_LOCK_DB | WM8962_TEMP_SHUT_DB,
+			   0);
+
 	if (wm8962->pdata.in4_dc_measure) {
 		ret = regmap_register_patch(wm8962->regmap,
 					    wm8962_dc_measure,
@@ -3714,6 +3681,37 @@ static int wm8962_i2c_probe(struct i2c_client *i2c,
 				ret);
 	}
 
+	if (wm8962->irq) {
+		if (pdata->irq_active_low) {
+			trigger = IRQF_TRIGGER_LOW;
+			irq_pol = WM8962_IRQ_POL;
+		} else {
+			trigger = IRQF_TRIGGER_HIGH;
+			irq_pol = 0;
+		}
+
+		regmap_update_bits(wm8962->regmap, WM8962_INTERRUPT_CONTROL,
+				   WM8962_IRQ_POL, irq_pol);
+
+		ret = devm_request_threaded_irq(&i2c->dev, wm8962->irq, NULL,
+						wm8962_irq,
+						trigger | IRQF_ONESHOT,
+						"wm8962", &i2c->dev);
+		if (ret != 0) {
+			dev_err(&i2c->dev, "Failed to request IRQ %d: %d\n",
+				wm8962->irq, ret);
+			wm8962->irq = 0;
+			/* Non-fatal */
+		} else {
+			/* Enable some IRQs by default */
+			regmap_update_bits(wm8962->regmap,
+					   WM8962_INTERRUPT_STATUS_2_MASK,
+					   WM8962_FLL_LOCK_EINT |
+					   WM8962_TEMP_SHUT_EINT |
+					   WM8962_FIFOS_ERR_EINT, 0);
+		}
+	}
+
 	pm_runtime_enable(&i2c->dev);
 	pm_request_idle(&i2c->dev);