b43: Remove unused phy_a code

gcc-6 reports the following error with -Werror=unused-const-variable.

drivers/net/wireless/broadcom/b43/phy_a.c:576:40: error:
	'b43_phyops_a' defined but not used

Per Michael Büsch: "All a-phy code is usused", so remove it all,
and move the remaining Type-G initialization code into phy_g.c.

Reported-by: Fengguang Wu <fengguang.wu@intel.com> [0-day test robot]
Cc: Michael Büsch <m@bues.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

drivers/net/wireless/broadcom/b43/Makefile

 b43-y				+= main.o
 b43-y				+= bus.o
-b43-$(CONFIG_B43_PHY_G)		+= phy_a.o phy_g.o tables.o lo.o wa.o
+b43-$(CONFIG_B43_PHY_G)		+= phy_g.o tables.o lo.o wa.o
 b43-$(CONFIG_B43_PHY_N)		+= tables_nphy.o
 b43-$(CONFIG_B43_PHY_N)		+= radio_2055.o
 b43-$(CONFIG_B43_PHY_N)		+= radio_2056.o

drivers/net/wireless/broadcom/b43/phy_a.h

@@ -101,26 +101,4 @@ u32 b43_ofdmtab_read32(struct b43_wldev *dev, u16 table, u16 offset);
 void b43_ofdmtab_write32(struct b43_wldev *dev, u16 table,
 			 u16 offset, u32 value);
 
-
-struct b43_phy_a {
-	/* Pointer to the table used to convert a
-	 * TSSI value to dBm-Q5.2 */
-	const s8 *tssi2dbm;
-	/* Target idle TSSI */
-	int tgt_idle_tssi;
-	/* Current idle TSSI */
-	int cur_idle_tssi;//FIXME value currently not set
-
-	/* A-PHY TX Power control value. */
-	u16 txpwr_offset;
-
-	//TODO lots of missing stuff
-};
-
-/**
- * b43_phy_inita - Lowlevel A-PHY init routine.
- * This is _only_ used by the G-PHY code.
- */
-void b43_phy_inita(struct b43_wldev *dev);
-
 #endif /* LINUX_B43_PHY_A_H_ */

drivers/net/wireless/broadcom/b43/phy_common.h

@@ -190,7 +190,6 @@ struct b43_phy_operations {
 	void (*pwork_60sec)(struct b43_wldev *dev);
 };
 
-struct b43_phy_a;
 struct b43_phy_g;
 struct b43_phy_n;
 struct b43_phy_lp;
@@ -210,8 +209,6 @@ struct b43_phy {
 #else
 	union {
 #endif
-		/* A-PHY specific information */
-		struct b43_phy_a *a;
 		/* G-PHY specific information */
 		struct b43_phy_g *g;
 		/* N-PHY specific information */

drivers/net/wireless/broadcom/b43/phy_g.c

@@ -31,6 +31,7 @@
 #include "phy_common.h"
 #include "lo.h"
 #include "main.h"
+#include "wa.h"
 
 #include <linux/bitrev.h>
 #include <linux/slab.h>
@@ -1987,6 +1988,25 @@ static void b43_phy_init_pctl(struct b43_wldev *dev)
 	b43_shm_clear_tssi(dev);
 }
 
+static void b43_phy_inita(struct b43_wldev *dev)
+{
+	struct b43_phy *phy = &dev->phy;
+
+	might_sleep();
+
+	if (phy->rev >= 6) {
+		if (b43_phy_read(dev, B43_PHY_ENCORE) & B43_PHY_ENCORE_EN)
+			b43_phy_set(dev, B43_PHY_ENCORE, 0x0010);
+		else
+			b43_phy_mask(dev, B43_PHY_ENCORE, ~0x1010);
+	}
+
+	b43_wa_all(dev);
+
+	if (dev->dev->bus_sprom->boardflags_lo & B43_BFL_PACTRL)
+		b43_phy_maskset(dev, B43_PHY_OFDM(0x6E), 0xE000, 0x3CF);
+}
+
 static void b43_phy_initg(struct b43_wldev *dev)
 {
 	struct b43_phy *phy = &dev->phy;
@@ -2150,11 +2170,6 @@ static void default_radio_attenuation(struct b43_wldev *dev,
 		}
 	}
 
-	if (phy->type == B43_PHYTYPE_A) {
-		rf->att = 0x60;
-		return;
-	}
-
 	switch (phy->radio_ver) {
 	case 0x2053:
 		switch (phy->radio_rev) {