Documentation/zram: add documentation for algorithm parameters

Document brief description of compression algorithms' parameters:
compression level and pre-trained dictionary.

[senozhatsky@chromium.org: trivial fixup]
  Link: https://lkml.kernel.org/r/20240903063722.1603592-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20240902105656.1383858-24-senozhatsky@chromium.orgSigned-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nick Terrell <terrelln@fb.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>

Documentation/admin-guide/blockdev/zram.rst

@@ -105,7 +105,38 @@ Examples::
 For the time being, the `comp_algorithm` content shows only compression
 algorithms that are supported by zram.
 
-4) Set Disksize
+4) Set compression algorithm parameters: Optional
+=================================================
+
+Compression algorithms may support specific parameters which can be
+tweaked for particular dataset. ZRAM has an `algorithm_params` device
+attribute which provides a per-algorithm params configuration.
+
+For example, several compression algorithms support `level` parameter.
+In addition, certain compression algorithms support pre-trained dictionaries,
+which significantly change algorithms' characteristics. In order to configure
+compression algorithm to use external pre-trained dictionary, pass full
+path to the `dict` along with other parameters::
+
+	#pass path to pre-trained zstd dictionary
+	echo "algo=zstd dict=/etc/dictioary" > /sys/block/zram0/algorithm_params
+
+	#same, but using algorithm priority
+	echo "priority=1 dict=/etc/dictioary" > \
+		/sys/block/zram0/algorithm_params
+
+	#pass path to pre-trained zstd dictionary and compression level
+	echo "algo=zstd level=8 dict=/etc/dictioary" > \
+		/sys/block/zram0/algorithm_params
+
+Parameters are algorithm specific: not all algorithms support pre-trained
+dictionaries, not all algorithms support `level`. Furthermore, for certain
+algorithms `level` controls the compression level (the higher the value the
+better the compression ratio, it even can take negatives values for some
+algorithms), for other algorithms `level` is acceleration level (the higher
+the value the lower the compression ratio).
+
+5) Set Disksize
 ===============
 
 Set disk size by writing the value to sysfs node 'disksize'.
@@ -125,7 +156,7 @@ There is little point creating a zram of greater than twice the size of memory
 since we expect a 2:1 compression ratio. Note that zram uses about 0.1% of the
 size of the disk when not in use so a huge zram is wasteful.
 
-5) Set memory limit: Optional
+6) Set memory limit: Optional
 =============================
 
 Set memory limit by writing the value to sysfs node 'mem_limit'.
@@ -144,7 +175,7 @@ Examples::
 	# To disable memory limit
 	echo 0 > /sys/block/zram0/mem_limit
 
-6) Activate
+7) Activate
 ===========
 
 ::
@@ -155,7 +186,7 @@ Examples::
 	mkfs.ext4 /dev/zram1
 	mount /dev/zram1 /tmp
 
-7) Add/remove zram devices
+8) Add/remove zram devices
 ==========================
 
 zram provides a control interface, which enables dynamic (on-demand) device
@@ -175,7 +206,7 @@ execute::
 
 	echo X > /sys/class/zram-control/hot_remove
 
-8) Stats
+9) Stats
 ========
 
 Per-device statistics are exported as various nodes under /sys/block/zram<id>/
@@ -277,15 +308,15 @@ a single line of text and contains the following stats separated by whitespace:
 		Unit: 4K bytes
  ============== =============================================================
 
-9) Deactivate
-=============
+10) Deactivate
+==============
 
 ::
 
 	swapoff /dev/zram0
 	umount /dev/zram1
 
-10) Reset
+11) Reset
 =========
 
 	Write any positive value to 'reset' sysfs node::