Skip to content

L
linux
Commit 98cd085e authored by Vinod Koul's avatar Vinod Koul
Browse files
Options

Merge branch 'topic/pl08x' into for-linus

parents 70ef9af7 fcc78541
Hide whitespace changes
Inline Side-by-side
Showing with 905 additions and 276 deletions
Documentation/devicetree/bindings/dma/arm-pl08x.txt
View file @ 98cd085e
......@@ -3,6 +3,11 @@
Required properties:
- compatible: "arm,pl080", "arm,primecell";
"arm,pl081", "arm,primecell";
"faraday,ftdmac020", "arm,primecell"
- arm,primecell-periphid: on the FTDMAC020 the primecell ID is not hard-coded
in the hardware and must be specified here as <0x0003b080>. This number
follows the PrimeCell standard numbering using the JEP106 vendor code 0x38
for Faraday Technology.
- reg: Address range of the PL08x registers
- interrupt: The PL08x interrupt number
- clocks: The clock running the IP core clock
......@@ -20,8 +25,8 @@ Optional properties:
- dma-requests: contains the total number of DMA requests supported by the DMAC
- memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
64, 128 or 256 bytes are legal values
- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
values
- memcpy-bus-width: the bus width used for memcpy in bits: 8, 16 or 32 are legal
values, the Faraday FTDMAC020 can also accept 64 bits
Clients
Required properties:
......
arch/arm/mach-lpc32xx/phy3250.c
View file @ 98cd085e
......@@ -137,6 +137,9 @@ static void pl08x_put_signal(const struct pl08x_channel_data *cd, int ch)
}
static struct pl08x_platform_data pl08x_pd = {
/* Some reasonable memcpy defaults */
.memcpy_burst_size = PL08X_BURST_SZ_256,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.slave_channels = &pl08x_slave_channels[0],
.num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
.get_xfer_signal = pl08x_get_signal,
......
arch/arm/mach-s3c64xx/pl080.c
View file @ 98cd085e
......@@ -137,16 +137,10 @@ static const struct dma_slave_map s3c64xx_dma0_slave_map[] = {
};
struct pl08x_platform_data s3c64xx_dma0_plat_data = {
.memcpy_channel = {
.bus_id = "memcpy",
.cctl_memcpy =
(PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT |
PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE |
PL080_CONTROL_PROT_SYS),
},
.memcpy_burst_size = PL08X_BURST_SZ_4,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.memcpy_prot_buff = true,
.memcpy_prot_cache = true,
.lli_buses = PL08X_AHB1,
.mem_buses = PL08X_AHB1,
.get_xfer_signal = pl08x_get_xfer_signal,
......@@ -238,16 +232,10 @@ static const struct dma_slave_map s3c64xx_dma1_slave_map[] = {
};
struct pl08x_platform_data s3c64xx_dma1_plat_data = {
.memcpy_channel = {
.bus_id = "memcpy",
.cctl_memcpy =
(PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT |
PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE |
PL080_CONTROL_PROT_SYS),
},
.memcpy_burst_size = PL08X_BURST_SZ_4,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.memcpy_prot_buff = true,
.memcpy_prot_cache = true,
.lli_buses = PL08X_AHB1,
.mem_buses = PL08X_AHB1,
.get_xfer_signal = pl08x_get_xfer_signal,
......
arch/arm/mach-spear/spear3xx.c
View file @ 98cd085e
......@@ -44,16 +44,10 @@ struct pl022_ssp_controller pl022_plat_data = {
/* dmac device registration */
struct pl08x_platform_data pl080_plat_data = {
.memcpy_channel = {
.bus_id = "memcpy",
.cctl_memcpy =
(PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
PL080_CONTROL_PROT_SYS),
},
.memcpy_burst_size = PL08X_BURST_SZ_16,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.memcpy_prot_buff = true,
.memcpy_prot_cache = true,
.lli_buses = PL08X_AHB1,
.mem_buses = PL08X_AHB1,
.get_xfer_signal = pl080_get_signal,
......
arch/arm/mach-spear/spear6xx.c
View file @ 98cd085e
......@@ -322,16 +322,10 @@ static struct pl08x_channel_data spear600_dma_info[] = {
};
static struct pl08x_platform_data spear6xx_pl080_plat_data = {
.memcpy_channel = {
.bus_id = "memcpy",
.cctl_memcpy =
(PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
PL080_CONTROL_PROT_SYS),
},
.memcpy_burst_size = PL08X_BURST_SZ_16,
.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
.memcpy_prot_buff = true,
.memcpy_prot_cache = true,
.lli_buses = PL08X_AHB1,
.mem_buses = PL08X_AHB1,
.get_xfer_signal = pl080_get_signal,
......
drivers/dma/Kconfig
View file @ 98cd085e
......@@ -62,8 +62,10 @@ config AMBA_PL08X
select DMA_ENGINE
select DMA_VIRTUAL_CHANNELS
help
Platform has a PL08x DMAC device
which can provide DMA engine support
Say yes if your platform has a PL08x DMAC device which can
provide DMA engine support. This includes the original ARM
PL080 and PL081, Samsungs PL080 derivative and Faraday
Technology's FTDMAC020 PL080 derivative.
config AMCC_PPC440SPE_ADMA
tristate "AMCC PPC440SPe ADMA support"
......
drivers/dma/amba-pl08x.c
View file @ 98cd085e
/*
* Copyright (c) 2006 ARM Ltd.
* Copyright (c) 2010 ST-Ericsson SA
* Copyirght (c) 2017 Linaro Ltd.
*
* Author: Peter Pearse <peter.pearse@arm.com>
* Author: Linus Walleij <linus.walleij@stericsson.com>
* Author: Linus Walleij <linus.walleij@linaro.org>
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the Free
......@@ -110,11 +111,12 @@ struct pl08x_driver_data;
* @channels: the number of channels available in this variant
* @signals: the number of request signals available from the hardware
* @dualmaster: whether this version supports dual AHB masters or not.
* @nomadik: whether the channels have Nomadik security extension bits
* that need to be checked for permission before use and some registers are
* missing
* @pl080s: whether this version is a PL080S, which has separate register and
* LLI word for transfer size.
* @nomadik: whether this variant is a ST Microelectronics Nomadik, where the
* channels have Nomadik security extension bits that need to be checked
* for permission before use and some registers are missing
* @pl080s: whether this variant is a Samsung PL080S, which has separate
* register and LLI word for transfer size.
* @ftdmac020: whether this variant is a Faraday Technology FTDMAC020
* @max_transfer_size: the maximum single element transfer size for this
* PL08x variant.
*/
......@@ -125,6 +127,7 @@ struct vendor_data {
bool dualmaster;
bool nomadik;
bool pl080s;
bool ftdmac020;
u32 max_transfer_size;
};
......@@ -148,19 +151,34 @@ struct pl08x_bus_data {
* @id: physical index to this channel
* @base: memory base address for this physical channel
* @reg_config: configuration address for this physical channel
* @reg_control: control address for this physical channel
* @reg_src: transfer source address register
* @reg_dst: transfer destination address register
* @reg_lli: transfer LLI address register
* @reg_busy: if the variant has a special per-channel busy register,
* this contains a pointer to it
* @lock: a lock to use when altering an instance of this struct
* @serving: the virtual channel currently being served by this physical
* channel
* @locked: channel unavailable for the system, e.g. dedicated to secure
* world
* @ftdmac020: channel is on a FTDMAC020
* @pl080s: channel is on a PL08s
*/
struct pl08x_phy_chan {
unsigned int id;
void __iomem *base;
void __iomem *reg_config;
void __iomem *reg_control;
void __iomem *reg_src;
void __iomem *reg_dst;
void __iomem *reg_lli;
void __iomem *reg_busy;
spinlock_t lock;
struct pl08x_dma_chan *serving;
bool locked;
bool ftdmac020;
bool pl080s;
};
/**
......@@ -253,8 +271,9 @@ struct pl08x_dma_chan {
/**
* struct pl08x_driver_data - the local state holder for the PL08x
* @slave: slave engine for this instance
* @slave: optional slave engine for this instance
* @memcpy: memcpy engine for this instance
* @has_slave: the PL08x has a slave engine (routed signals)
* @base: virtual memory base (remapped) for the PL08x
* @adev: the corresponding AMBA (PrimeCell) bus entry
* @vd: vendor data for this PL08x variant
......@@ -269,6 +288,7 @@ struct pl08x_dma_chan {
struct pl08x_driver_data {
struct dma_device slave;
struct dma_device memcpy;
bool has_slave;
void __iomem *base;
struct amba_device *adev;
const struct vendor_data *vd;
......@@ -360,10 +380,24 @@ static int pl08x_phy_channel_busy(struct pl08x_phy_chan *ch)
{
unsigned int val;
/* If we have a special busy register, take a shortcut */
if (ch->reg_busy) {
val = readl(ch->reg_busy);
return !!(val & BIT(ch->id));
}
val = readl(ch->reg_config);
return val & PL080_CONFIG_ACTIVE;
}
/*
* pl08x_write_lli() - Write an LLI into the DMA controller.
*
* The PL08x derivatives support linked lists, but the first item of the
* list containing the source, destination, control word and next LLI is
* ignored. Instead the driver has to write those values directly into the
* SRC, DST, LLI and control registers. On FTDMAC020 also the SIZE
* register need to be set up for the first transfer.
*/
static void pl08x_write_lli(struct pl08x_driver_data *pl08x,
struct pl08x_phy_chan *phychan, const u32 *lli, u32 ccfg)
{
......@@ -381,11 +415,112 @@ static void pl08x_write_lli(struct pl08x_driver_data *pl08x,
phychan->id, lli[PL080_LLI_SRC], lli[PL080_LLI_DST],
lli[PL080_LLI_LLI], lli[PL080_LLI_CCTL], ccfg);
writel_relaxed(lli[PL080_LLI_SRC], phychan->base + PL080_CH_SRC_ADDR);
writel_relaxed(lli[PL080_LLI_DST], phychan->base + PL080_CH_DST_ADDR);
writel_relaxed(lli[PL080_LLI_LLI], phychan->base + PL080_CH_LLI);
writel_relaxed(lli[PL080_LLI_CCTL], phychan->base + PL080_CH_CONTROL);
writel_relaxed(lli[PL080_LLI_SRC], phychan->reg_src);
writel_relaxed(lli[PL080_LLI_DST], phychan->reg_dst);
writel_relaxed(lli[PL080_LLI_LLI], phychan->reg_lli);
/*
* The FTMAC020 has a different layout in the CCTL word of the LLI
* and the CCTL register which is split in CSR and SIZE registers.
* Convert the LLI item CCTL into the proper values to write into
* the CSR and SIZE registers.
*/
if (phychan->ftdmac020) {
u32 llictl = lli[PL080_LLI_CCTL];
u32 val = 0;
/* Write the transfer size (12 bits) to the size register */
writel_relaxed(llictl & FTDMAC020_LLI_TRANSFER_SIZE_MASK,
phychan->base + FTDMAC020_CH_SIZE);
/*
* Then write the control bits 28..16 to the control register
* by shuffleing the bits around to where they are in the
* main register. The mapping is as follows:
* Bit 28: TC_MSK - mask on all except last LLI
* Bit 27..25: SRC_WIDTH
* Bit 24..22: DST_WIDTH
* Bit 21..20: SRCAD_CTRL
* Bit 19..17: DSTAD_CTRL
* Bit 17: SRC_SEL
* Bit 16: DST_SEL
*/
if (llictl & FTDMAC020_LLI_TC_MSK)
val |= FTDMAC020_CH_CSR_TC_MSK;
val |= ((llictl & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
(FTDMAC020_LLI_SRC_WIDTH_SHIFT -
FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT));
val |= ((llictl & FTDMAC020_LLI_DST_WIDTH_MSK) >>
(FTDMAC020_LLI_DST_WIDTH_SHIFT -
FTDMAC020_CH_CSR_DST_WIDTH_SHIFT));
val |= ((llictl & FTDMAC020_LLI_SRCAD_CTL_MSK) >>
(FTDMAC020_LLI_SRCAD_CTL_SHIFT -
FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT));
val |= ((llictl & FTDMAC020_LLI_DSTAD_CTL_MSK) >>
(FTDMAC020_LLI_DSTAD_CTL_SHIFT -
FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT));
if (llictl & FTDMAC020_LLI_SRC_SEL)
val |= FTDMAC020_CH_CSR_SRC_SEL;
if (llictl & FTDMAC020_LLI_DST_SEL)
val |= FTDMAC020_CH_CSR_DST_SEL;
/*
* Set up the bits that exist in the CSR but are not
* part the LLI, i.e. only gets written to the control
* register right here.
*
* FIXME: do not just handle memcpy, also handle slave DMA.
*/
switch (pl08x->pd->memcpy_burst_size) {
default:
case PL08X_BURST_SZ_1:
val |= PL080_BSIZE_1 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_4:
val |= PL080_BSIZE_4 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_8:
val |= PL080_BSIZE_8 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_16:
val |= PL080_BSIZE_16 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_32:
val |= PL080_BSIZE_32 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_64:
val |= PL080_BSIZE_64 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_128:
val |= PL080_BSIZE_128 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_256:
val |= PL080_BSIZE_256 <<
FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
break;
}
/* Protection flags */
if (pl08x->pd->memcpy_prot_buff)
val |= FTDMAC020_CH_CSR_PROT2;
if (pl08x->pd->memcpy_prot_cache)
val |= FTDMAC020_CH_CSR_PROT3;
/* We are the kernel, so we are in privileged mode */
val |= FTDMAC020_CH_CSR_PROT1;
writel_relaxed(val, phychan->reg_control);
} else {
/* Bits are just identical */
writel_relaxed(lli[PL080_LLI_CCTL], phychan->reg_control);
}
/* Second control word on the PL080s */
if (pl08x->vd->pl080s)
writel_relaxed(lli[PL080S_LLI_CCTL2],
phychan->base + PL080S_CH_CONTROL2);
......@@ -423,11 +558,25 @@ static void pl08x_start_next_txd(struct pl08x_dma_chan *plchan)
cpu_relax();
/* Do not access config register until channel shows as inactive */
val = readl(phychan->reg_config);
while ((val & PL080_CONFIG_ACTIVE) || (val & PL080_CONFIG_ENABLE))
if (phychan->ftdmac020) {
val = readl(phychan->reg_config);
while (val & FTDMAC020_CH_CFG_BUSY)
val = readl(phychan->reg_config);
val = readl(phychan->reg_control);
while (val & FTDMAC020_CH_CSR_EN)
val = readl(phychan->reg_control);
writel(val | FTDMAC020_CH_CSR_EN,
phychan->reg_control);
} else {
val = readl(phychan->reg_config);
while ((val & PL080_CONFIG_ACTIVE) ||
(val & PL080_CONFIG_ENABLE))
val = readl(phychan->reg_config);
writel(val | PL080_CONFIG_ENABLE, phychan->reg_config);
writel(val | PL080_CONFIG_ENABLE, phychan->reg_config);
}
}
/*
......@@ -445,6 +594,14 @@ static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
u32 val;
int timeout;
if (ch->ftdmac020) {
/* Use the enable bit on the FTDMAC020 */
val = readl(ch->reg_control);
val &= ~FTDMAC020_CH_CSR_EN;
writel(val, ch->reg_control);
return;
}
/* Set the HALT bit and wait for the FIFO to drain */
val = readl(ch->reg_config);
val |= PL080_CONFIG_HALT;
......@@ -464,6 +621,14 @@ static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
{
u32 val;
/* Use the enable bit on the FTDMAC020 */
if (ch->ftdmac020) {
val = readl(ch->reg_control);
val |= FTDMAC020_CH_CSR_EN;
writel(val, ch->reg_control);
return;
}
/* Clear the HALT bit */
val = readl(ch->reg_config);
val &= ~PL080_CONFIG_HALT;
......@@ -479,25 +644,68 @@ static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
struct pl08x_phy_chan *ch)
{
u32 val = readl(ch->reg_config);
u32 val;
/* The layout for the FTDMAC020 is different */
if (ch->ftdmac020) {
/* Disable all interrupts */
val = readl(ch->reg_config);
val |= (FTDMAC020_CH_CFG_INT_ABT_MASK |
FTDMAC020_CH_CFG_INT_ERR_MASK |
FTDMAC020_CH_CFG_INT_TC_MASK);
writel(val, ch->reg_config);
/* Abort and disable channel */
val = readl(ch->reg_control);
val &= ~FTDMAC020_CH_CSR_EN;
val |= FTDMAC020_CH_CSR_ABT;
writel(val, ch->reg_control);
/* Clear ABT and ERR interrupt flags */
writel(BIT(ch->id) | BIT(ch->id + 16),
pl08x->base + PL080_ERR_CLEAR);
writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
return;
}
val = readl(ch->reg_config);
val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
PL080_CONFIG_TC_IRQ_MASK);
writel(val, ch->reg_config);
writel(BIT(ch->id), pl08x->base + PL080_ERR_CLEAR);
writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
}
static inline u32 get_bytes_in_cctl(u32 cctl)
static u32 get_bytes_in_phy_channel(struct pl08x_phy_chan *ch)
{
/* The source width defines the number of bytes */
u32 bytes = cctl & PL080_CONTROL_TRANSFER_SIZE_MASK;
u32 val;
u32 bytes;
if (ch->ftdmac020) {
bytes = readl(ch->base + FTDMAC020_CH_SIZE);
cctl &= PL080_CONTROL_SWIDTH_MASK;
val = readl(ch->reg_control);
val &= FTDMAC020_CH_CSR_SRC_WIDTH_MSK;
val >>= FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT;
} else if (ch->pl080s) {
val = readl(ch->base + PL080S_CH_CONTROL2);
bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
switch (cctl >> PL080_CONTROL_SWIDTH_SHIFT) {
val = readl(ch->reg_control);
val &= PL080_CONTROL_SWIDTH_MASK;
val >>= PL080_CONTROL_SWIDTH_SHIFT;
} else {
/* Plain PL08x */
val = readl(ch->reg_control);
bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
val &= PL080_CONTROL_SWIDTH_MASK;
val >>= PL080_CONTROL_SWIDTH_SHIFT;
}
switch (val) {
case PL080_WIDTH_8BIT:
break;
case PL080_WIDTH_16BIT:
......@@ -510,14 +718,35 @@ static inline u32 get_bytes_in_cctl(u32 cctl)
return bytes;
}
static inline u32 get_bytes_in_cctl_pl080s(u32 cctl, u32 cctl1)
static u32 get_bytes_in_lli(struct pl08x_phy_chan *ch, const u32 *llis_va)
{
/* The source width defines the number of bytes */
u32 bytes = cctl1 & PL080S_CONTROL_TRANSFER_SIZE_MASK;
u32 val;
u32 bytes;
if (ch->ftdmac020) {
val = llis_va[PL080_LLI_CCTL];
bytes = val & FTDMAC020_LLI_TRANSFER_SIZE_MASK;
val = llis_va[PL080_LLI_CCTL];
val &= FTDMAC020_LLI_SRC_WIDTH_MSK;
val >>= FTDMAC020_LLI_SRC_WIDTH_SHIFT;
} else if (ch->pl080s) {
val = llis_va[PL080S_LLI_CCTL2];
bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
val = llis_va[PL080_LLI_CCTL];
val &= PL080_CONTROL_SWIDTH_MASK;
val >>= PL080_CONTROL_SWIDTH_SHIFT;
} else {
/* Plain PL08x */
val = llis_va[PL080_LLI_CCTL];
bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
cctl &= PL080_CONTROL_SWIDTH_MASK;
val &= PL080_CONTROL_SWIDTH_MASK;
val >>= PL080_CONTROL_SWIDTH_SHIFT;
}
switch (cctl >> PL080_CONTROL_SWIDTH_SHIFT) {
switch (val) {
case PL080_WIDTH_8BIT:
break;
case PL080_WIDTH_16BIT:
......@@ -552,15 +781,10 @@ static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
* Follow the LLIs to get the number of remaining
* bytes in the currently active transaction.
*/
clli = readl(ch->base + PL080_CH_LLI) & ~PL080_LLI_LM_AHB2;
clli = readl(ch->reg_lli) & ~PL080_LLI_LM_AHB2;
/* First get the remaining bytes in the active transfer */
if (pl08x->vd->pl080s)
bytes = get_bytes_in_cctl_pl080s(
readl(ch->base + PL080_CH_CONTROL),
readl(ch->base + PL080S_CH_CONTROL2));
else
bytes = get_bytes_in_cctl(readl(ch->base + PL080_CH_CONTROL));
bytes = get_bytes_in_phy_channel(ch);
if (!clli)
return bytes;
......@@ -581,12 +805,7 @@ static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
llis_va_limit = llis_va + llis_max_words;
for (; llis_va < llis_va_limit; llis_va += pl08x->lli_words) {
if (pl08x->vd->pl080s)
bytes += get_bytes_in_cctl_pl080s(
llis_va[PL080_LLI_CCTL],
llis_va[PL080S_LLI_CCTL2]);
else
bytes += get_bytes_in_cctl(llis_va[PL080_LLI_CCTL]);
bytes += get_bytes_in_lli(ch, llis_va);
/*
* A LLI pointer going backward terminates the LLI list
......@@ -705,7 +924,7 @@ static void pl08x_phy_free(struct pl08x_dma_chan *plchan)
break;
}
if (!next) {
if (!next && pl08x->has_slave) {
list_for_each_entry(p, &pl08x->slave.channels, vc.chan.device_node)
if (p->state == PL08X_CHAN_WAITING) {
next = p;
......@@ -746,9 +965,30 @@ static void pl08x_phy_free(struct pl08x_dma_chan *plchan)
* LLI handling
*/
static inline unsigned int pl08x_get_bytes_for_cctl(unsigned int coded)
static inline unsigned int
pl08x_get_bytes_for_lli(struct pl08x_driver_data *pl08x,
u32 cctl,
bool source)
{
switch (coded) {
u32 val;
if (pl08x->vd->ftdmac020) {
if (source)
val = (cctl & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
FTDMAC020_LLI_SRC_WIDTH_SHIFT;
else
val = (cctl & FTDMAC020_LLI_DST_WIDTH_MSK) >>
FTDMAC020_LLI_DST_WIDTH_SHIFT;
} else {
if (source)
val = (cctl & PL080_CONTROL_SWIDTH_MASK) >>
PL080_CONTROL_SWIDTH_SHIFT;
else
val = (cctl & PL080_CONTROL_DWIDTH_MASK) >>
PL080_CONTROL_DWIDTH_SHIFT;
}
switch (val) {
case PL080_WIDTH_8BIT:
return 1;
case PL080_WIDTH_16BIT:
......@@ -762,49 +1002,106 @@ static inline unsigned int pl08x_get_bytes_for_cctl(unsigned int coded)
return 0;
}
static inline u32 pl08x_cctl_bits(u32 cctl, u8 srcwidth, u8 dstwidth,
size_t tsize)
static inline u32 pl08x_lli_control_bits(struct pl08x_driver_data *pl08x,
u32 cctl,
u8 srcwidth, u8 dstwidth,
size_t tsize)
{
u32 retbits = cctl;
/* Remove all src, dst and transfer size bits */
retbits &= ~PL080_CONTROL_DWIDTH_MASK;
retbits &= ~PL080_CONTROL_SWIDTH_MASK;
retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
/*
* Remove all src, dst and transfer size bits, then set the
* width and size according to the parameters. The bit offsets
* are different in the FTDMAC020 so we need to accound for this.
*/
if (pl08x->vd->ftdmac020) {
retbits &= ~FTDMAC020_LLI_DST_WIDTH_MSK;
retbits &= ~FTDMAC020_LLI_SRC_WIDTH_MSK;
retbits &= ~FTDMAC020_LLI_TRANSFER_SIZE_MASK;
switch (srcwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT <<
FTDMAC020_LLI_SRC_WIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT <<
FTDMAC020_LLI_SRC_WIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT <<
FTDMAC020_LLI_SRC_WIDTH_SHIFT;
break;
default:
BUG();
break;
}
/* Then set the bits according to the parameters */
switch (srcwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT;
break;
default:
BUG();
break;
}
switch (dstwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT <<
FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT <<
FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT <<
FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
default:
BUG();
break;
}
switch (dstwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
default:
BUG();
break;
tsize &= FTDMAC020_LLI_TRANSFER_SIZE_MASK;
retbits |= tsize << FTDMAC020_LLI_TRANSFER_SIZE_SHIFT;
} else {
retbits &= ~PL080_CONTROL_DWIDTH_MASK;
retbits &= ~PL080_CONTROL_SWIDTH_MASK;
retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
switch (srcwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT <<
PL080_CONTROL_SWIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT <<
PL080_CONTROL_SWIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT <<
PL080_CONTROL_SWIDTH_SHIFT;
break;
default:
BUG();
break;
}
switch (dstwidth) {
case 1:
retbits |= PL080_WIDTH_8BIT <<
PL080_CONTROL_DWIDTH_SHIFT;
break;
case 2:
retbits |= PL080_WIDTH_16BIT <<
PL080_CONTROL_DWIDTH_SHIFT;
break;
case 4:
retbits |= PL080_WIDTH_32BIT <<
PL080_CONTROL_DWIDTH_SHIFT;
break;
default:
BUG();
break;
}
tsize &= PL080_CONTROL_TRANSFER_SIZE_MASK;
retbits |= tsize << PL080_CONTROL_TRANSFER_SIZE_SHIFT;
}
tsize &= PL080_CONTROL_TRANSFER_SIZE_MASK;
retbits |= tsize << PL080_CONTROL_TRANSFER_SIZE_SHIFT;
return retbits;
}
......@@ -825,13 +1122,35 @@ struct pl08x_lli_build_data {
* - prefers the destination bus if both available
* - prefers bus with fixed address (i.e. peripheral)
*/
static void pl08x_choose_master_bus(struct pl08x_lli_build_data *bd,
struct pl08x_bus_data **mbus, struct pl08x_bus_data **sbus, u32 cctl)
static void pl08x_choose_master_bus(struct pl08x_driver_data *pl08x,
struct pl08x_lli_build_data *bd,
struct pl08x_bus_data **mbus,
struct pl08x_bus_data **sbus,
u32 cctl)
{
if (!(cctl & PL080_CONTROL_DST_INCR)) {
bool dst_incr;
bool src_incr;
/*
* The FTDMAC020 only supports memory-to-memory transfer, so
* source and destination always increase.
*/
if (pl08x->vd->ftdmac020) {
dst_incr = true;
src_incr = true;
} else {
dst_incr = !!(cctl & PL080_CONTROL_DST_INCR);
src_incr = !!(cctl & PL080_CONTROL_SRC_INCR);
}
/*
* If either bus is not advancing, i.e. it is a peripheral, that
* one becomes master
*/
if (!dst_incr) {
*mbus = &bd->dstbus;
*sbus = &bd->srcbus;
} else if (!(cctl & PL080_CONTROL_SRC_INCR)) {
} else if (!src_incr) {
*mbus = &bd->srcbus;
*sbus = &bd->dstbus;
} else {
......@@ -869,10 +1188,16 @@ static void pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
if (pl08x->vd->pl080s)
llis_va[PL080S_LLI_CCTL2] = cctl2;
if (cctl & PL080_CONTROL_SRC_INCR)
if (pl08x->vd->ftdmac020) {
/* FIXME: only memcpy so far so both increase */
bd->srcbus.addr += len;
if (cctl & PL080_CONTROL_DST_INCR)
bd->dstbus.addr += len;
} else {
if (cctl & PL080_CONTROL_SRC_INCR)
bd->srcbus.addr += len;
if (cctl & PL080_CONTROL_DST_INCR)
bd->dstbus.addr += len;
}
BUG_ON(bd->remainder < len);
......@@ -883,12 +1208,12 @@ static inline void prep_byte_width_lli(struct pl08x_driver_data *pl08x,
struct pl08x_lli_build_data *bd, u32 *cctl, u32 len,
int num_llis, size_t *total_bytes)
{
*cctl = pl08x_cctl_bits(*cctl, 1, 1, len);
*cctl = pl08x_lli_control_bits(pl08x, *cctl, 1, 1, len);
pl08x_fill_lli_for_desc(pl08x, bd, num_llis, len, *cctl, len);
(*total_bytes) += len;
}
#ifdef VERBOSE_DEBUG
#if 1
static void pl08x_dump_lli(struct pl08x_driver_data *pl08x,
const u32 *llis_va, int num_llis)
{
......@@ -953,14 +1278,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
cctl = txd->cctl;
/* Find maximum width of the source bus */
bd.srcbus.maxwidth =
pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_SWIDTH_MASK) >>
PL080_CONTROL_SWIDTH_SHIFT);
bd.srcbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, true);
/* Find maximum width of the destination bus */
bd.dstbus.maxwidth =
pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_DWIDTH_MASK) >>
PL080_CONTROL_DWIDTH_SHIFT);
bd.dstbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, false);
list_for_each_entry(dsg, &txd->dsg_list, node) {
total_bytes = 0;
......@@ -972,7 +1293,7 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
bd.srcbus.buswidth = bd.srcbus.maxwidth;
bd.dstbus.buswidth = bd.dstbus.maxwidth;
pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
pl08x_choose_master_bus(pl08x, &bd, &mbus, &sbus, cctl);
dev_vdbg(&pl08x->adev->dev,
"src=0x%08llx%s/%u dst=0x%08llx%s/%u len=%zu\n",
......@@ -1009,8 +1330,14 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
* supported. Thus, we can't have scattered addresses.
*/
if (!bd.remainder) {
u32 fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >>
PL080_CONFIG_FLOW_CONTROL_SHIFT;
u32 fc;
/* FTDMAC020 only does memory-to-memory */
if (pl08x->vd->ftdmac020)
fc = PL080_FLOW_MEM2MEM;
else
fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >>
PL080_CONFIG_FLOW_CONTROL_SHIFT;
if (!((fc >= PL080_FLOW_SRC2DST_DST) &&
(fc <= PL080_FLOW_SRC2DST_SRC))) {
dev_err(&pl08x->adev->dev, "%s sg len can't be zero",
......@@ -1027,8 +1354,9 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
return 0;
}
cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth,
bd.dstbus.buswidth, 0);
cctl = pl08x_lli_control_bits(pl08x, cctl,
bd.srcbus.buswidth, bd.dstbus.buswidth,
0);
pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
0, cctl, 0);
break;
......@@ -1107,8 +1435,9 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
"size 0x%08zx (remainder 0x%08zx)\n",
__func__, lli_len, bd.remainder);
cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth,
bd.dstbus.buswidth, tsize);
cctl = pl08x_lli_control_bits(pl08x, cctl,
bd.srcbus.buswidth, bd.dstbus.buswidth,
tsize);
pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
lli_len, cctl, tsize);
total_bytes += lli_len;
......@@ -1151,7 +1480,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
/* The final LLI terminates the LLI. */
last_lli[PL080_LLI_LLI] = 0;
/* The final LLI element shall also fire an interrupt. */
last_lli[PL080_LLI_CCTL] |= PL080_CONTROL_TC_IRQ_EN;
if (pl08x->vd->ftdmac020)
last_lli[PL080_LLI_CCTL] &= ~FTDMAC020_LLI_TC_MSK;
else
last_lli[PL080_LLI_CCTL] |= PL080_CONTROL_TC_IRQ_EN;
}
pl08x_dump_lli(pl08x, llis_va, num_llis);
......@@ -1317,14 +1649,25 @@ static const struct burst_table burst_sizes[] = {
* will be routed to each port. We try to have source and destination
* on separate ports, but always respect the allowable settings.
*/
static u32 pl08x_select_bus(u8 src, u8 dst)
static u32 pl08x_select_bus(bool ftdmac020, u8 src, u8 dst)
{
u32 cctl = 0;
u32 dst_ahb2;
u32 src_ahb2;
/* The FTDMAC020 use different bits to indicate src/dst bus */
if (ftdmac020) {
dst_ahb2 = FTDMAC020_LLI_DST_SEL;
src_ahb2 = FTDMAC020_LLI_SRC_SEL;
} else {
dst_ahb2 = PL080_CONTROL_DST_AHB2;
src_ahb2 = PL080_CONTROL_SRC_AHB2;
}
if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
cctl |= PL080_CONTROL_DST_AHB2;
cctl |= dst_ahb2;
if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
cctl |= PL080_CONTROL_SRC_AHB2;
cctl |= src_ahb2;
return cctl;
}
......@@ -1412,14 +1755,134 @@ static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan)
{
struct pl08x_txd *txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
if (txd) {
if (txd)
INIT_LIST_HEAD(&txd->dsg_list);
return txd;
}
/* Always enable error and terminal interrupts */
txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
PL080_CONFIG_TC_IRQ_MASK;
static u32 pl08x_memcpy_cctl(struct pl08x_driver_data *pl08x)
{
u32 cctl = 0;
/* Conjure cctl */
switch (pl08x->pd->memcpy_burst_size) {
default:
dev_err(&pl08x->adev->dev,
"illegal burst size for memcpy, set to 1\n");
/* Fall through */
case PL08X_BURST_SZ_1:
cctl |= PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_4:
cctl |= PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_8:
cctl |= PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_16:
cctl |= PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_32:
cctl |= PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_64:
cctl |= PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_128:
cctl |= PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
case PL08X_BURST_SZ_256:
cctl |= PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT;
break;
}
return txd;
switch (pl08x->pd->memcpy_bus_width) {
default:
dev_err(&pl08x->adev->dev,
"illegal bus width for memcpy, set to 8 bits\n");
/* Fall through */
case PL08X_BUS_WIDTH_8_BITS:
cctl |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
case PL08X_BUS_WIDTH_16_BITS:
cctl |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
case PL08X_BUS_WIDTH_32_BITS:
cctl |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
break;
}
/* Protection flags */
if (pl08x->pd->memcpy_prot_buff)
cctl |= PL080_CONTROL_PROT_BUFF;
if (pl08x->pd->memcpy_prot_cache)
cctl |= PL080_CONTROL_PROT_CACHE;
/* We are the kernel, so we are in privileged mode */
cctl |= PL080_CONTROL_PROT_SYS;
/* Both to be incremented or the code will break */
cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
if (pl08x->vd->dualmaster)
cctl |= pl08x_select_bus(false,
pl08x->mem_buses,
pl08x->mem_buses);
return cctl;
}
static u32 pl08x_ftdmac020_memcpy_cctl(struct pl08x_driver_data *pl08x)
{
u32 cctl = 0;
/* Conjure cctl */
switch (pl08x->pd->memcpy_bus_width) {
default:
dev_err(&pl08x->adev->dev,
"illegal bus width for memcpy, set to 8 bits\n");
/* Fall through */
case PL08X_BUS_WIDTH_8_BITS:
cctl |= PL080_WIDTH_8BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
PL080_WIDTH_8BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
case PL08X_BUS_WIDTH_16_BITS:
cctl |= PL080_WIDTH_16BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
PL080_WIDTH_16BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
case PL08X_BUS_WIDTH_32_BITS:
cctl |= PL080_WIDTH_32BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
PL080_WIDTH_32BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
break;
}
/*
* By default mask the TC IRQ on all LLIs, it will be unmasked on
* the last LLI item by other code.
*/
cctl |= FTDMAC020_LLI_TC_MSK;
/*
* Both to be incremented so leave bits FTDMAC020_LLI_SRCAD_CTL
* and FTDMAC020_LLI_DSTAD_CTL as zero
*/
if (pl08x->vd->dualmaster)
cctl |= pl08x_select_bus(true,
pl08x->mem_buses,
pl08x->mem_buses);
return cctl;
}
/*
......@@ -1452,18 +1915,16 @@ static struct dma_async_tx_descriptor *pl08x_prep_dma_memcpy(
dsg->src_addr = src;
dsg->dst_addr = dest;
dsg->len = len;
/* Set platform data for m2m */
txd->ccfg |= PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
txd->cctl = pl08x->pd->memcpy_channel.cctl_memcpy &
~(PL080_CONTROL_DST_AHB2 | PL080_CONTROL_SRC_AHB2);
/* Both to be incremented or the code will break */
txd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
if (pl08x->vd->dualmaster)
txd->cctl |= pl08x_select_bus(pl08x->mem_buses,
pl08x->mem_buses);
if (pl08x->vd->ftdmac020) {
/* Writing CCFG zero ENABLES all interrupts */
txd->ccfg = 0;
txd->cctl = pl08x_ftdmac020_memcpy_cctl(pl08x);
} else {
txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
PL080_CONFIG_TC_IRQ_MASK |
PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
txd->cctl = pl08x_memcpy_cctl(pl08x);
}
ret = pl08x_fill_llis_for_desc(plchan->host, txd);
if (!ret) {
......@@ -1527,7 +1988,7 @@ static struct pl08x_txd *pl08x_init_txd(
return NULL;
}
txd->cctl = cctl | pl08x_select_bus(src_buses, dst_buses);
txd->cctl = cctl | pl08x_select_bus(false, src_buses, dst_buses);
if (plchan->cfg.device_fc)
tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER_PER :
......@@ -1536,7 +1997,9 @@ static struct pl08x_txd *pl08x_init_txd(
tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER :
PL080_FLOW_PER2MEM;
txd->ccfg |= tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT;
txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
PL080_CONFIG_TC_IRQ_MASK |
tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT;
ret = pl08x_request_mux(plchan);
if (ret < 0) {
......@@ -1813,6 +2276,11 @@ static void pl08x_ensure_on(struct pl08x_driver_data *pl08x)
/* The Nomadik variant does not have the config register */
if (pl08x->vd->nomadik)
return;
/* The FTDMAC020 variant does this in another register */
if (pl08x->vd->ftdmac020) {
writel(PL080_CONFIG_ENABLE, pl08x->base + FTDMAC020_CSR);
return;
}
writel(PL080_CONFIG_ENABLE, pl08x->base + PL080_CONFIG);
}
......@@ -1925,9 +2393,16 @@ static int pl08x_dma_init_virtual_channels(struct pl08x_driver_data *pl08x,
chan->signal = i;
pl08x_dma_slave_init(chan);
} else {
chan->cd = &pl08x->pd->memcpy_channel;
chan->cd = kzalloc(sizeof(*chan->cd), GFP_KERNEL);
if (!chan->cd) {
kfree(chan);
return -ENOMEM;
}
chan->cd->bus_id = "memcpy";
chan->cd->periph_buses = pl08x->pd->mem_buses;
chan->name = kasprintf(GFP_KERNEL, "memcpy%d", i);
if (!chan->name) {
kfree(chan->cd);
kfree(chan);
return -ENOMEM;
}
......@@ -2009,12 +2484,15 @@ static int pl08x_debugfs_show(struct seq_file *s, void *data)
pl08x_state_str(chan->state));
}
seq_printf(s, "\nPL08x virtual slave channels:\n");
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->slave.channels, vc.chan.device_node) {
seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
if (pl08x->has_slave) {
seq_printf(s, "\nPL08x virtual slave channels:\n");
seq_printf(s, "CHANNEL:\tSTATE:\n");
seq_printf(s, "--------\t------\n");
list_for_each_entry(chan, &pl08x->slave.channels,
vc.chan.device_node) {
seq_printf(s, "%s\t\t%s\n", chan->name,
pl08x_state_str(chan->state));
}
}
return 0;
......@@ -2052,6 +2530,10 @@ static struct dma_chan *pl08x_find_chan_id(struct pl08x_driver_data *pl08x,
{
struct pl08x_dma_chan *chan;
/* Trying to get a slave channel from something with no slave support */
if (!pl08x->has_slave)
return NULL;
list_for_each_entry(chan, &pl08x->slave.channels, vc.chan.device_node) {
if (chan->signal == id)
return &chan->vc.chan;
......@@ -2099,7 +2581,6 @@ static int pl08x_of_probe(struct amba_device *adev,
{
struct pl08x_platform_data *pd;
struct pl08x_channel_data *chanp = NULL;
u32 cctl_memcpy = 0;
u32 val;
int ret;
int i;
......@@ -2139,36 +2620,28 @@ static int pl08x_of_probe(struct amba_device *adev,
dev_err(&adev->dev, "illegal burst size for memcpy, set to 1\n");
/* Fall through */
case 1:
cctl_memcpy |= PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_1;
break;
case 4:
cctl_memcpy |= PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_4;
break;
case 8:
cctl_memcpy |= PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_8;
break;
case 16:
cctl_memcpy |= PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_16;
break;
case 32:
cctl_memcpy |= PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_32;
break;
case 64:
cctl_memcpy |= PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_64;
break;
case 128:
cctl_memcpy |= PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_128;
break;
case 256:
cctl_memcpy |= PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT |
PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT;
pd->memcpy_burst_size = PL08X_BURST_SZ_256;
break;
}
......@@ -2182,48 +2655,40 @@ static int pl08x_of_probe(struct amba_device *adev,
dev_err(&adev->dev, "illegal bus width for memcpy, set to 8 bits\n");
/* Fall through */
case 8:
cctl_memcpy |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
pd->memcpy_bus_width = PL08X_BUS_WIDTH_8_BITS;
break;
case 16:
cctl_memcpy |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
pd->memcpy_bus_width = PL08X_BUS_WIDTH_16_BITS;
break;
case 32:
cctl_memcpy |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
pd->memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS;
break;
}
/* This is currently the only thing making sense */
cctl_memcpy |= PL080_CONTROL_PROT_SYS;
/* Set up memcpy channel */
pd->memcpy_channel.bus_id = "memcpy";
pd->memcpy_channel.cctl_memcpy = cctl_memcpy;
/* Use the buses that can access memory, obviously */
pd->memcpy_channel.periph_buses = pd->mem_buses;
/*
* Allocate channel data for all possible slave channels (one
* for each possible signal), channels will then be allocated
* for a device and have it's AHB interfaces set up at
* translation time.
*/
chanp = devm_kcalloc(&adev->dev,
pl08x->vd->signals,
sizeof(struct pl08x_channel_data),
GFP_KERNEL);
if (!chanp)
return -ENOMEM;
if (pl08x->vd->signals) {
chanp = devm_kcalloc(&adev->dev,
pl08x->vd->signals,
sizeof(struct pl08x_channel_data),
GFP_KERNEL);
if (!chanp)
return -ENOMEM;
pd->slave_channels = chanp;
for (i = 0; i < pl08x->vd->signals; i++) {
/* chanp->periph_buses will be assigned at translation */
chanp->bus_id = kasprintf(GFP_KERNEL, "slave%d", i);
chanp++;
pd->slave_channels = chanp;
for (i = 0; i < pl08x->vd->signals; i++) {
/*
* chanp->periph_buses will be assigned at translation
*/
chanp->bus_id = kasprintf(GFP_KERNEL, "slave%d", i);
chanp++;
}
pd->num_slave_channels = pl08x->vd->signals;
}
pd->num_slave_channels = pl08x->vd->signals;
pl08x->pd = pd;
......@@ -2242,7 +2707,7 @@ static inline int pl08x_of_probe(struct amba_device *adev,
static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
{
struct pl08x_driver_data *pl08x;
const struct vendor_data *vd = id->data;
struct vendor_data *vd = id->data;
struct device_node *np = adev->dev.of_node;
u32 tsfr_size;
int ret = 0;
......@@ -2268,6 +2733,34 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
pl08x->adev = adev;
pl08x->vd = vd;
pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
if (!pl08x->base) {
ret = -ENOMEM;
goto out_no_ioremap;
}
if (vd->ftdmac020) {
u32 val;
val = readl(pl08x->base + FTDMAC020_REVISION);
dev_info(&pl08x->adev->dev, "FTDMAC020 %d.%d rel %d\n",
(val >> 16) & 0xff, (val >> 8) & 0xff, val & 0xff);
val = readl(pl08x->base + FTDMAC020_FEATURE);
dev_info(&pl08x->adev->dev, "FTDMAC020 %d channels, "
"%s built-in bridge, %s, %s linked lists\n",
(val >> 12) & 0x0f,
(val & BIT(10)) ? "no" : "has",
(val & BIT(9)) ? "AHB0 and AHB1" : "AHB0",
(val & BIT(8)) ? "supports" : "does not support");
/* Vendor data from feature register */
if (!(val & BIT(8)))
dev_warn(&pl08x->adev->dev,
"linked lists not supported, required\n");
vd->channels = (val >> 12) & 0x0f;
vd->dualmaster = !!(val & BIT(9));
}
/* Initialize memcpy engine */
dma_cap_set(DMA_MEMCPY, pl08x->memcpy.cap_mask);
pl08x->memcpy.dev = &adev->dev;
......@@ -2284,25 +2777,38 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
pl08x->memcpy.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
pl08x->memcpy.directions = BIT(DMA_MEM_TO_MEM);
pl08x->memcpy.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
if (vd->ftdmac020)
pl08x->memcpy.copy_align = DMAENGINE_ALIGN_4_BYTES;
/* Initialize slave engine */
dma_cap_set(DMA_SLAVE, pl08x->slave.cap_mask);
dma_cap_set(DMA_CYCLIC, pl08x->slave.cap_mask);
pl08x->slave.dev = &adev->dev;
pl08x->slave.device_free_chan_resources = pl08x_free_chan_resources;
pl08x->slave.device_prep_dma_interrupt = pl08x_prep_dma_interrupt;
pl08x->slave.device_tx_status = pl08x_dma_tx_status;
pl08x->slave.device_issue_pending = pl08x_issue_pending;
pl08x->slave.device_prep_slave_sg = pl08x_prep_slave_sg;
pl08x->slave.device_prep_dma_cyclic = pl08x_prep_dma_cyclic;
pl08x->slave.device_config = pl08x_config;
pl08x->slave.device_pause = pl08x_pause;
pl08x->slave.device_resume = pl08x_resume;
pl08x->slave.device_terminate_all = pl08x_terminate_all;
pl08x->slave.src_addr_widths = PL80X_DMA_BUSWIDTHS;
pl08x->slave.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
pl08x->slave.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
pl08x->slave.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
/*
* Initialize slave engine, if the block has no signals, that means
* we have no slave support.
*/
if (vd->signals) {
pl08x->has_slave = true;
dma_cap_set(DMA_SLAVE, pl08x->slave.cap_mask);
dma_cap_set(DMA_CYCLIC, pl08x->slave.cap_mask);
pl08x->slave.dev = &adev->dev;
pl08x->slave.device_free_chan_resources =
pl08x_free_chan_resources;
pl08x->slave.device_prep_dma_interrupt =
pl08x_prep_dma_interrupt;
pl08x->slave.device_tx_status = pl08x_dma_tx_status;
pl08x->slave.device_issue_pending = pl08x_issue_pending;
pl08x->slave.device_prep_slave_sg = pl08x_prep_slave_sg;
pl08x->slave.device_prep_dma_cyclic = pl08x_prep_dma_cyclic;
pl08x->slave.device_config = pl08x_config;
pl08x->slave.device_pause = pl08x_pause;
pl08x->slave.device_resume = pl08x_resume;
pl08x->slave.device_terminate_all = pl08x_terminate_all;
pl08x->slave.src_addr_widths = PL80X_DMA_BUSWIDTHS;
pl08x->slave.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
pl08x->slave.directions =
BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
pl08x->slave.residue_granularity =
DMA_RESIDUE_GRANULARITY_SEGMENT;
}
/* Get the platform data */
pl08x->pd = dev_get_platdata(&adev->dev);
......@@ -2344,19 +2850,18 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
goto out_no_lli_pool;
}
pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
if (!pl08x->base) {
ret = -ENOMEM;
goto out_no_ioremap;
}
/* Turn on the PL08x */
pl08x_ensure_on(pl08x);
/* Attach the interrupt handler */
writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
/* Clear any pending interrupts */
if (vd->ftdmac020)
/* This variant has error IRQs in bits 16-19 */
writel(0x0000FFFF, pl08x->base + PL080_ERR_CLEAR);
else
writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
writel(0x000000FF, pl08x->base + PL080_TC_CLEAR);
/* Attach the interrupt handler */
ret = request_irq(adev->irq[0], pl08x_irq, 0, DRIVER_NAME, pl08x);
if (ret) {
dev_err(&adev->dev, "%s failed to request interrupt %d\n",
......@@ -2377,7 +2882,25 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
ch->id = i;
ch->base = pl08x->base + PL080_Cx_BASE(i);
ch->reg_config = ch->base + vd->config_offset;
if (vd->ftdmac020) {
/* FTDMA020 has a special channel busy register */
ch->reg_busy = ch->base + FTDMAC020_CH_BUSY;
ch->reg_config = ch->base + FTDMAC020_CH_CFG;
ch->reg_control = ch->base + FTDMAC020_CH_CSR;
ch->reg_src = ch->base + FTDMAC020_CH_SRC_ADDR;
ch->reg_dst = ch->base + FTDMAC020_CH_DST_ADDR;
ch->reg_lli = ch->base + FTDMAC020_CH_LLP;
ch->ftdmac020 = true;
} else {
ch->reg_config = ch->base + vd->config_offset;
ch->reg_control = ch->base + PL080_CH_CONTROL;
ch->reg_src = ch->base + PL080_CH_SRC_ADDR;
ch->reg_dst = ch->base + PL080_CH_DST_ADDR;
ch->reg_lli = ch->base + PL080_CH_LLI;
}
if (vd->pl080s)
ch->pl080s = true;
spin_lock_init(&ch->lock);
/*
......@@ -2410,13 +2933,15 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
}
/* Register slave channels */
ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->slave,
pl08x->pd->num_slave_channels, true);
if (ret < 0) {
dev_warn(&pl08x->adev->dev,
"%s failed to enumerate slave channels - %d\n",
__func__, ret);
goto out_no_slave;
if (pl08x->has_slave) {
ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->slave,
pl08x->pd->num_slave_channels, true);
if (ret < 0) {
dev_warn(&pl08x->adev->dev,
"%s failed to enumerate slave channels - %d\n",
__func__, ret);
goto out_no_slave;
}
}
ret = dma_async_device_register(&pl08x->memcpy);
......@@ -2427,12 +2952,14 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
goto out_no_memcpy_reg;
}
ret = dma_async_device_register(&pl08x->slave);
if (ret) {
dev_warn(&pl08x->adev->dev,
if (pl08x->has_slave) {
ret = dma_async_device_register(&pl08x->slave);
if (ret) {
dev_warn(&pl08x->adev->dev,
"%s failed to register slave as an async device - %d\n",
__func__, ret);
goto out_no_slave_reg;
goto out_no_slave_reg;
}
}
amba_set_drvdata(adev, pl08x);
......@@ -2446,7 +2973,8 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
out_no_slave_reg:
dma_async_device_unregister(&pl08x->memcpy);
out_no_memcpy_reg:
pl08x_free_virtual_channels(&pl08x->slave);
if (pl08x->has_slave)
pl08x_free_virtual_channels(&pl08x->slave);
out_no_slave:
pl08x_free_virtual_channels(&pl08x->memcpy);
out_no_memcpy:
......@@ -2454,11 +2982,11 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
out_no_phychans:
free_irq(adev->irq[0], pl08x);
out_no_irq:
iounmap(pl08x->base);
out_no_ioremap:
dma_pool_destroy(pl08x->pool);
out_no_lli_pool:
out_no_platdata:
iounmap(pl08x->base);
out_no_ioremap:
kfree(pl08x);
out_no_pl08x:
amba_release_regions(adev);
......@@ -2499,6 +3027,12 @@ static struct vendor_data vendor_pl081 = {
.max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
};
static struct vendor_data vendor_ftdmac020 = {
.config_offset = PL080_CH_CONFIG,
.ftdmac020 = true,
.max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
};
static struct amba_id pl08x_ids[] = {
/* Samsung PL080S variant */
{
......@@ -2524,6 +3058,12 @@ static struct amba_id pl08x_ids[] = {
.mask = 0x00ffffff,
.data = &vendor_nomadik,
},
/* Faraday Technology FTDMAC020 */
{
.id = 0x0003b080,
.mask = 0x000fffff,
.data = &vendor_ftdmac020,
},
{ 0, 0 },
};
......
include/linux/amba/pl080.h
View file @ 98cd085e
......@@ -44,7 +44,14 @@
#define PL080_SYNC (0x34)
/* Per channel configuration registers */
/* The Faraday Technology FTDMAC020 variant registers */
#define FTDMAC020_CH_BUSY (0x20)
/* Identical to PL080_CONFIG */
#define FTDMAC020_CSR (0x24)
/* Identical to PL080_SYNC */
#define FTDMAC020_SYNC (0x2C)
#define FTDMAC020_REVISION (0x30)
#define FTDMAC020_FEATURE (0x34)
/* Per channel configuration registers */
#define PL080_Cx_BASE(x) ((0x100 + (x * 0x20)))
......@@ -55,13 +62,20 @@
#define PL080_CH_CONFIG (0x10)
#define PL080S_CH_CONTROL2 (0x10)
#define PL080S_CH_CONFIG (0x14)
#define PL080_LLI_ADDR_MASK (0x3fffffff << 2)
/* The Faraday FTDMAC020 derivative shuffles the registers around */
#define FTDMAC020_CH_CSR (0x00)
#define FTDMAC020_CH_CFG (0x04)
#define FTDMAC020_CH_SRC_ADDR (0x08)
#define FTDMAC020_CH_DST_ADDR (0x0C)
#define FTDMAC020_CH_LLP (0x10)
#define FTDMAC020_CH_SIZE (0x14)
#define PL080_LLI_ADDR_MASK GENMASK(31, 2)
#define PL080_LLI_ADDR_SHIFT (2)
#define PL080_LLI_LM_AHB2 BIT(0)
#define PL080_CONTROL_TC_IRQ_EN BIT(31)
#define PL080_CONTROL_PROT_MASK (0x7 << 28)
#define PL080_CONTROL_PROT_MASK GENMASK(30, 28)
#define PL080_CONTROL_PROT_SHIFT (28)
#define PL080_CONTROL_PROT_CACHE BIT(30)
#define PL080_CONTROL_PROT_BUFF BIT(29)
......@@ -70,16 +84,16 @@
#define PL080_CONTROL_SRC_INCR BIT(26)
#define PL080_CONTROL_DST_AHB2 BIT(25)
#define PL080_CONTROL_SRC_AHB2 BIT(24)
#define PL080_CONTROL_DWIDTH_MASK (0x7 << 21)
#define PL080_CONTROL_DWIDTH_MASK GENMASK(23, 21)
#define PL080_CONTROL_DWIDTH_SHIFT (21)
#define PL080_CONTROL_SWIDTH_MASK (0x7 << 18)
#define PL080_CONTROL_SWIDTH_MASK GENMASK(20, 18)
#define PL080_CONTROL_SWIDTH_SHIFT (18)
#define PL080_CONTROL_DB_SIZE_MASK (0x7 << 15)
#define PL080_CONTROL_DB_SIZE_MASK GENMASK(17, 15)
#define PL080_CONTROL_DB_SIZE_SHIFT (15)
#define PL080_CONTROL_SB_SIZE_MASK (0x7 << 12)
#define PL080_CONTROL_SB_SIZE_MASK GENMASK(14, 12)
#define PL080_CONTROL_SB_SIZE_SHIFT (12)
#define PL080_CONTROL_TRANSFER_SIZE_MASK (0xfff << 0)
#define PL080S_CONTROL_TRANSFER_SIZE_MASK (0x1ffffff << 0)
#define PL080_CONTROL_TRANSFER_SIZE_MASK GENMASK(11, 0)
#define PL080S_CONTROL_TRANSFER_SIZE_MASK GENMASK(24, 0)
#define PL080_CONTROL_TRANSFER_SIZE_SHIFT (0)
#define PL080_BSIZE_1 (0x0)
......@@ -102,11 +116,11 @@
#define PL080_CONFIG_LOCK BIT(16)
#define PL080_CONFIG_TC_IRQ_MASK BIT(15)
#define PL080_CONFIG_ERR_IRQ_MASK BIT(14)
#define PL080_CONFIG_FLOW_CONTROL_MASK (0x7 << 11)
#define PL080_CONFIG_FLOW_CONTROL_MASK GENMASK(13, 11)
#define PL080_CONFIG_FLOW_CONTROL_SHIFT (11)
#define PL080_CONFIG_DST_SEL_MASK (0xf << 6)
#define PL080_CONFIG_DST_SEL_MASK GENMASK(9, 6)
#define PL080_CONFIG_DST_SEL_SHIFT (6)
#define PL080_CONFIG_SRC_SEL_MASK (0xf << 1)
#define PL080_CONFIG_SRC_SEL_MASK GENMASK(4, 1)
#define PL080_CONFIG_SRC_SEL_SHIFT (1)
#define PL080_CONFIG_ENABLE BIT(0)
......@@ -119,6 +133,73 @@
#define PL080_FLOW_PER2MEM_PER (0x6)
#define PL080_FLOW_SRC2DST_SRC (0x7)
#define FTDMAC020_CH_CSR_TC_MSK BIT(31)
/* Later versions have a threshold in bits 24..26, */
#define FTDMAC020_CH_CSR_FIFOTH_MSK GENMASK(26, 24)
#define FTDMAC020_CH_CSR_FIFOTH_SHIFT (24)
#define FTDMAC020_CH_CSR_CHPR1_MSK GENMASK(23, 22)
#define FTDMAC020_CH_CSR_PROT3 BIT(21)
#define FTDMAC020_CH_CSR_PROT2 BIT(20)
#define FTDMAC020_CH_CSR_PROT1 BIT(19)
#define FTDMAC020_CH_CSR_SRC_SIZE_MSK GENMASK(18, 16)
#define FTDMAC020_CH_CSR_SRC_SIZE_SHIFT (16)
#define FTDMAC020_CH_CSR_ABT BIT(15)
#define FTDMAC020_CH_CSR_SRC_WIDTH_MSK GENMASK(13, 11)
#define FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT (11)
#define FTDMAC020_CH_CSR_DST_WIDTH_MSK GENMASK(10, 8)
#define FTDMAC020_CH_CSR_DST_WIDTH_SHIFT (8)
#define FTDMAC020_CH_CSR_MODE BIT(7)
/* 00 = increase, 01 = decrease, 10 = fix */
#define FTDMAC020_CH_CSR_SRCAD_CTL_MSK GENMASK(6, 5)
#define FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT (5)
#define FTDMAC020_CH_CSR_DSTAD_CTL_MSK GENMASK(4, 3)
#define FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT (3)
#define FTDMAC020_CH_CSR_SRC_SEL BIT(2)
#define FTDMAC020_CH_CSR_DST_SEL BIT(1)
#define FTDMAC020_CH_CSR_EN BIT(0)
/* FIFO threshold setting */
#define FTDMAC020_CH_CSR_FIFOTH_1 (0x0)
#define FTDMAC020_CH_CSR_FIFOTH_2 (0x1)
#define FTDMAC020_CH_CSR_FIFOTH_4 (0x2)
#define FTDMAC020_CH_CSR_FIFOTH_8 (0x3)
#define FTDMAC020_CH_CSR_FIFOTH_16 (0x4)
/* The FTDMAC020 supports 64bit wide transfers */
#define FTDMAC020_WIDTH_64BIT (0x3)
/* Address can be increased, decreased or fixed */
#define FTDMAC020_CH_CSR_SRCAD_CTL_INC (0x0)
#define FTDMAC020_CH_CSR_SRCAD_CTL_DEC (0x1)
#define FTDMAC020_CH_CSR_SRCAD_CTL_FIXED (0x2)
#define FTDMAC020_CH_CFG_LLP_CNT_MASK GENMASK(19, 16)
#define FTDMAC020_CH_CFG_LLP_CNT_SHIFT (16)
#define FTDMAC020_CH_CFG_BUSY BIT(8)
#define FTDMAC020_CH_CFG_INT_ABT_MASK BIT(2)
#define FTDMAC020_CH_CFG_INT_ERR_MASK BIT(1)
#define FTDMAC020_CH_CFG_INT_TC_MASK BIT(0)
/* Inside the LLIs, the applicable CSR fields are mapped differently */
#define FTDMAC020_LLI_TC_MSK BIT(28)
#define FTDMAC020_LLI_SRC_WIDTH_MSK GENMASK(27, 25)
#define FTDMAC020_LLI_SRC_WIDTH_SHIFT (25)
#define FTDMAC020_LLI_DST_WIDTH_MSK GENMASK(24, 22)
#define FTDMAC020_LLI_DST_WIDTH_SHIFT (22)
#define FTDMAC020_LLI_SRCAD_CTL_MSK GENMASK(21, 20)
#define FTDMAC020_LLI_SRCAD_CTL_SHIFT (20)
#define FTDMAC020_LLI_DSTAD_CTL_MSK GENMASK(19, 18)
#define FTDMAC020_LLI_DSTAD_CTL_SHIFT (18)
#define FTDMAC020_LLI_SRC_SEL BIT(17)
#define FTDMAC020_LLI_DST_SEL BIT(16)
#define FTDMAC020_LLI_TRANSFER_SIZE_MASK GENMASK(11, 0)
#define FTDMAC020_LLI_TRANSFER_SIZE_SHIFT (0)
#define FTDMAC020_CFG_LLP_CNT_MASK GENMASK(19, 16)
#define FTDMAC020_CFG_LLP_CNT_SHIFT (16)
#define FTDMAC020_CFG_BUSY BIT(8)
#define FTDMAC020_CFG_INT_ABT_MSK BIT(2)
#define FTDMAC020_CFG_INT_ERR_MSK BIT(1)
#define FTDMAC020_CFG_INT_TC_MSK BIT(0)
/* DMA linked list chain structure */
struct pl080_lli {
......
include/linux/amba/pl08x.h
View file @ 98cd085e
......@@ -47,8 +47,6 @@ enum {
* devices with static assignments
* @muxval: a number usually used to poke into some mux regiser to
* mux in the signal to this channel
* @cctl_memcpy: options for the channel control register for memcpy
* *** not used for slave channels ***
* @addr: source/target address in physical memory for this DMA channel,
* can be the address of a FIFO register for burst requests for example.
* This can be left undefined if the PrimeCell API is used for configuring
......@@ -63,12 +61,28 @@ struct pl08x_channel_data {
int min_signal;
int max_signal;
u32 muxval;
u32 cctl_memcpy;
dma_addr_t addr;
bool single;
u8 periph_buses;
};
enum pl08x_burst_size {
PL08X_BURST_SZ_1,
PL08X_BURST_SZ_4,
PL08X_BURST_SZ_8,
PL08X_BURST_SZ_16,
PL08X_BURST_SZ_32,
PL08X_BURST_SZ_64,
PL08X_BURST_SZ_128,
PL08X_BURST_SZ_256,
};
enum pl08x_bus_width {
PL08X_BUS_WIDTH_8_BITS,
PL08X_BUS_WIDTH_16_BITS,
PL08X_BUS_WIDTH_32_BITS,
};
/**
* struct pl08x_platform_data - the platform configuration for the PL08x
* PrimeCells.
......@@ -76,6 +90,11 @@ struct pl08x_channel_data {
* platform, all inclusive, including multiplexed channels. The available
* physical channels will be multiplexed around these signals as they are
* requested, just enumerate all possible channels.
* @num_slave_channels: number of elements in the slave channel array
* @memcpy_burst_size: the appropriate burst size for memcpy operations
* @memcpy_bus_width: memory bus width
* @memcpy_prot_buff: whether memcpy DMA is bufferable
* @memcpy_prot_cache: whether memcpy DMA is cacheable
* @get_xfer_signal: request a physical signal to be used for a DMA transfer
* immediately: if there is some multiplexing or similar blocking the use
* of the channel the transfer can be denied by returning less than zero,
......@@ -90,7 +109,10 @@ struct pl08x_channel_data {
struct pl08x_platform_data {
struct pl08x_channel_data *slave_channels;
unsigned int num_slave_channels;
struct pl08x_channel_data memcpy_channel;
enum pl08x_burst_size memcpy_burst_size;
enum pl08x_bus_width memcpy_bus_width;
bool memcpy_prot_buff;
bool memcpy_prot_cache;
int (*get_xfer_signal)(const struct pl08x_channel_data *);
void (*put_xfer_signal)(const struct pl08x_channel_data *, int);
u8 lli_buses;
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7