Merge branch 'topic/pl08x' into for-linus

Documentation/devicetree/bindings/dma/arm-pl08x.txt

@@ -3,6 +3,11 @@
 Required properties:
 - compatible: "arm,pl080", "arm,primecell";
 	      "arm,pl081", "arm,primecell";
+	      "faraday,ftdmac020", "arm,primecell"
+- arm,primecell-periphid: on the FTDMAC020 the primecell ID is not hard-coded
+  in the hardware and must be specified here as <0x0003b080>. This number
+  follows the PrimeCell standard numbering using the JEP106 vendor code 0x38
+  for Faraday Technology.
 - reg: Address range of the PL08x registers
 - interrupt: The PL08x interrupt number
 - clocks: The clock running the IP core clock
@@ -20,8 +25,8 @@ Optional properties:
 - dma-requests: contains the total number of DMA requests supported by the DMAC
 - memcpy-burst-size: the size of the bursts for memcpy: 1, 4, 8, 16, 32
   64, 128 or 256 bytes are legal values
-- memcpy-bus-width: the bus width used for memcpy: 8, 16 or 32 are legal
-  values
+- memcpy-bus-width: the bus width used for memcpy in bits: 8, 16 or 32 are legal
+  values, the Faraday FTDMAC020 can also accept 64 bits
 
 Clients
 Required properties:

arch/arm/mach-lpc32xx/phy3250.c

@@ -137,6 +137,9 @@ static void pl08x_put_signal(const struct pl08x_channel_data *cd, int ch)
 }
 
 static struct pl08x_platform_data pl08x_pd = {
+	/* Some reasonable memcpy defaults */
+	.memcpy_burst_size = PL08X_BURST_SZ_256,
+	.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
 	.slave_channels = &pl08x_slave_channels[0],
 	.num_slave_channels = ARRAY_SIZE(pl08x_slave_channels),
 	.get_xfer_signal = pl08x_get_signal,

arch/arm/mach-s3c64xx/pl080.c

@@ -137,16 +137,10 @@ static const struct dma_slave_map s3c64xx_dma0_slave_map[] = {
 };
 
 struct pl08x_platform_data s3c64xx_dma0_plat_data = {
-	.memcpy_channel = {
-		.bus_id = "memcpy",
-		.cctl_memcpy =
-			(PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
-			PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT |
-			PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
-			PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT |
-			PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE |
-			PL080_CONTROL_PROT_SYS),
-	},
+	.memcpy_burst_size = PL08X_BURST_SZ_4,
+	.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
+	.memcpy_prot_buff = true,
+	.memcpy_prot_cache = true,
 	.lli_buses = PL08X_AHB1,
 	.mem_buses = PL08X_AHB1,
 	.get_xfer_signal = pl08x_get_xfer_signal,
@@ -238,16 +232,10 @@ static const struct dma_slave_map s3c64xx_dma1_slave_map[] = {
 };
 
 struct pl08x_platform_data s3c64xx_dma1_plat_data = {
-	.memcpy_channel = {
-		.bus_id = "memcpy",
-		.cctl_memcpy =
-			(PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
-			PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT |
-			PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
-			PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT |
-			PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE |
-			PL080_CONTROL_PROT_SYS),
-	},
+	.memcpy_burst_size = PL08X_BURST_SZ_4,
+	.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
+	.memcpy_prot_buff = true,
+	.memcpy_prot_cache = true,
 	.lli_buses = PL08X_AHB1,
 	.mem_buses = PL08X_AHB1,
 	.get_xfer_signal = pl08x_get_xfer_signal,

arch/arm/mach-spear/spear3xx.c

@@ -44,16 +44,10 @@ struct pl022_ssp_controller pl022_plat_data = {
 
 /* dmac device registration */
 struct pl08x_platform_data pl080_plat_data = {
-	.memcpy_channel = {
-		.bus_id = "memcpy",
-		.cctl_memcpy =
-			(PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
-			PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
-			PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
-			PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
-			PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
-			PL080_CONTROL_PROT_SYS),
-	},
+	.memcpy_burst_size = PL08X_BURST_SZ_16,
+	.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
+	.memcpy_prot_buff = true,
+	.memcpy_prot_cache = true,
 	.lli_buses = PL08X_AHB1,
 	.mem_buses = PL08X_AHB1,
 	.get_xfer_signal = pl080_get_signal,

arch/arm/mach-spear/spear6xx.c

@@ -322,16 +322,10 @@ static struct pl08x_channel_data spear600_dma_info[] = {
 };
 
 static struct pl08x_platform_data spear6xx_pl080_plat_data = {
-	.memcpy_channel = {
-		.bus_id = "memcpy",
-		.cctl_memcpy =
-			(PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT | \
-			PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT | \
-			PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT | \
-			PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT | \
-			PL080_CONTROL_PROT_BUFF | PL080_CONTROL_PROT_CACHE | \
-			PL080_CONTROL_PROT_SYS),
-	},
+	.memcpy_burst_size = PL08X_BURST_SZ_16,
+	.memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS,
+	.memcpy_prot_buff = true,
+	.memcpy_prot_cache = true,
 	.lli_buses = PL08X_AHB1,
 	.mem_buses = PL08X_AHB1,
 	.get_xfer_signal = pl080_get_signal,

drivers/dma/Kconfig

@@ -62,8 +62,10 @@ config AMBA_PL08X
 	select DMA_ENGINE
 	select DMA_VIRTUAL_CHANNELS
 	help
-	  Platform has a PL08x DMAC device
-	  which can provide DMA engine support
+	  Say yes if your platform has a PL08x DMAC device which can
+	  provide DMA engine support. This includes the original ARM
+	  PL080 and PL081, Samsungs PL080 derivative and Faraday
+	  Technology's FTDMAC020 PL080 derivative.
 
 config AMCC_PPC440SPE_ADMA
 	tristate "AMCC PPC440SPe ADMA support"

drivers/dma/amba-pl08x.c

 /*
  * Copyright (c) 2006 ARM Ltd.
  * Copyright (c) 2010 ST-Ericsson SA
+ * Copyirght (c) 2017 Linaro Ltd.
  *
  * Author: Peter Pearse <peter.pearse@arm.com>
- * Author: Linus Walleij <linus.walleij@stericsson.com>
+ * Author: Linus Walleij <linus.walleij@linaro.org>
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the Free
@@ -110,11 +111,12 @@ struct pl08x_driver_data;
  * @channels: the number of channels available in this variant
  * @signals: the number of request signals available from the hardware
  * @dualmaster: whether this version supports dual AHB masters or not.
- * @nomadik: whether the channels have Nomadik security extension bits
- *	that need to be checked for permission before use and some registers are
- *	missing
- * @pl080s: whether this version is a PL080S, which has separate register and
- *	LLI word for transfer size.
+ * @nomadik: whether this variant is a ST Microelectronics Nomadik, where the
+ *	channels have Nomadik security extension bits that need to be checked
+ *	for permission before use and some registers are missing
+ * @pl080s: whether this variant is a Samsung PL080S, which has separate
+ *	register and LLI word for transfer size.
+ * @ftdmac020: whether this variant is a Faraday Technology FTDMAC020
  * @max_transfer_size: the maximum single element transfer size for this
  *	PL08x variant.
  */
@@ -125,6 +127,7 @@ struct vendor_data {
 	bool dualmaster;
 	bool nomadik;
 	bool pl080s;
+	bool ftdmac020;
 	u32 max_transfer_size;
 };
 
@@ -148,19 +151,34 @@ struct pl08x_bus_data {
  * @id: physical index to this channel
  * @base: memory base address for this physical channel
  * @reg_config: configuration address for this physical channel
+ * @reg_control: control address for this physical channel
+ * @reg_src: transfer source address register
+ * @reg_dst: transfer destination address register
+ * @reg_lli: transfer LLI address register
+ * @reg_busy: if the variant has a special per-channel busy register,
+ * this contains a pointer to it
  * @lock: a lock to use when altering an instance of this struct
  * @serving: the virtual channel currently being served by this physical
  * channel
  * @locked: channel unavailable for the system, e.g. dedicated to secure
  * world
+ * @ftdmac020: channel is on a FTDMAC020
+ * @pl080s: channel is on a PL08s
  */
 struct pl08x_phy_chan {
 	unsigned int id;
 	void __iomem *base;
 	void __iomem *reg_config;
+	void __iomem *reg_control;
+	void __iomem *reg_src;
+	void __iomem *reg_dst;
+	void __iomem *reg_lli;
+	void __iomem *reg_busy;
 	spinlock_t lock;
 	struct pl08x_dma_chan *serving;
 	bool locked;
+	bool ftdmac020;
+	bool pl080s;
 };
 
 /**
@@ -253,8 +271,9 @@ struct pl08x_dma_chan {
 
 /**
  * struct pl08x_driver_data - the local state holder for the PL08x
- * @slave: slave engine for this instance
+ * @slave: optional slave engine for this instance
  * @memcpy: memcpy engine for this instance
+ * @has_slave: the PL08x has a slave engine (routed signals)
  * @base: virtual memory base (remapped) for the PL08x
  * @adev: the corresponding AMBA (PrimeCell) bus entry
  * @vd: vendor data for this PL08x variant
@@ -269,6 +288,7 @@ struct pl08x_dma_chan {
 struct pl08x_driver_data {
 	struct dma_device slave;
 	struct dma_device memcpy;
+	bool has_slave;
 	void __iomem *base;
 	struct amba_device *adev;
 	const struct vendor_data *vd;
@@ -360,10 +380,24 @@ static int pl08x_phy_channel_busy(struct pl08x_phy_chan *ch)
 {
 	unsigned int val;
 
+	/* If we have a special busy register, take a shortcut */
+	if (ch->reg_busy) {
+		val = readl(ch->reg_busy);
+		return !!(val & BIT(ch->id));
+	}
 	val = readl(ch->reg_config);
 	return val & PL080_CONFIG_ACTIVE;
 }
 
+/*
+ * pl08x_write_lli() - Write an LLI into the DMA controller.
+ *
+ * The PL08x derivatives support linked lists, but the first item of the
+ * list containing the source, destination, control word and next LLI is
+ * ignored. Instead the driver has to write those values directly into the
+ * SRC, DST, LLI and control registers. On FTDMAC020 also the SIZE
+ * register need to be set up for the first transfer.
+ */
 static void pl08x_write_lli(struct pl08x_driver_data *pl08x,
 		struct pl08x_phy_chan *phychan, const u32 *lli, u32 ccfg)
 {
@@ -381,11 +415,112 @@ static void pl08x_write_lli(struct pl08x_driver_data *pl08x,
 			phychan->id, lli[PL080_LLI_SRC], lli[PL080_LLI_DST],
 			lli[PL080_LLI_LLI], lli[PL080_LLI_CCTL], ccfg);
 
-	writel_relaxed(lli[PL080_LLI_SRC], phychan->base + PL080_CH_SRC_ADDR);
-	writel_relaxed(lli[PL080_LLI_DST], phychan->base + PL080_CH_DST_ADDR);
-	writel_relaxed(lli[PL080_LLI_LLI], phychan->base + PL080_CH_LLI);
-	writel_relaxed(lli[PL080_LLI_CCTL], phychan->base + PL080_CH_CONTROL);
+	writel_relaxed(lli[PL080_LLI_SRC], phychan->reg_src);
+	writel_relaxed(lli[PL080_LLI_DST], phychan->reg_dst);
+	writel_relaxed(lli[PL080_LLI_LLI], phychan->reg_lli);
+
+	/*
+	 * The FTMAC020 has a different layout in the CCTL word of the LLI
+	 * and the CCTL register which is split in CSR and SIZE registers.
+	 * Convert the LLI item CCTL into the proper values to write into
+	 * the CSR and SIZE registers.
+	 */
+	if (phychan->ftdmac020) {
+		u32 llictl = lli[PL080_LLI_CCTL];
+		u32 val = 0;
+
+		/* Write the transfer size (12 bits) to the size register */
+		writel_relaxed(llictl & FTDMAC020_LLI_TRANSFER_SIZE_MASK,
+			       phychan->base + FTDMAC020_CH_SIZE);
+		/*
+		 * Then write the control bits 28..16 to the control register
+		 * by shuffleing the bits around to where they are in the
+		 * main register. The mapping is as follows:
+		 * Bit 28: TC_MSK - mask on all except last LLI
+		 * Bit 27..25: SRC_WIDTH
+		 * Bit 24..22: DST_WIDTH
+		 * Bit 21..20: SRCAD_CTRL
+		 * Bit 19..17: DSTAD_CTRL
+		 * Bit 17: SRC_SEL
+		 * Bit 16: DST_SEL
+		 */
+		if (llictl & FTDMAC020_LLI_TC_MSK)
+			val |= FTDMAC020_CH_CSR_TC_MSK;
+		val |= ((llictl  & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
+			(FTDMAC020_LLI_SRC_WIDTH_SHIFT -
+			 FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT));
+		val |= ((llictl  & FTDMAC020_LLI_DST_WIDTH_MSK) >>
+			(FTDMAC020_LLI_DST_WIDTH_SHIFT -
+			 FTDMAC020_CH_CSR_DST_WIDTH_SHIFT));
+		val |= ((llictl  & FTDMAC020_LLI_SRCAD_CTL_MSK) >>
+			(FTDMAC020_LLI_SRCAD_CTL_SHIFT -
+			 FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT));
+		val |= ((llictl  & FTDMAC020_LLI_DSTAD_CTL_MSK) >>
+			(FTDMAC020_LLI_DSTAD_CTL_SHIFT -
+			 FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT));
+		if (llictl & FTDMAC020_LLI_SRC_SEL)
+			val |= FTDMAC020_CH_CSR_SRC_SEL;
+		if (llictl & FTDMAC020_LLI_DST_SEL)
+			val |= FTDMAC020_CH_CSR_DST_SEL;
+
+		/*
+		 * Set up the bits that exist in the CSR but are not
+		 * part the LLI, i.e. only gets written to the control
+		 * register right here.
+		 *
+		 * FIXME: do not just handle memcpy, also handle slave DMA.
+		 */
+		switch (pl08x->pd->memcpy_burst_size) {
+		default:
+		case PL08X_BURST_SZ_1:
+			val |= PL080_BSIZE_1 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_4:
+			val |= PL080_BSIZE_4 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_8:
+			val |= PL080_BSIZE_8 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_16:
+			val |= PL080_BSIZE_16 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_32:
+			val |= PL080_BSIZE_32 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_64:
+			val |= PL080_BSIZE_64 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_128:
+			val |= PL080_BSIZE_128 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		case PL08X_BURST_SZ_256:
+			val |= PL080_BSIZE_256 <<
+				FTDMAC020_CH_CSR_SRC_SIZE_SHIFT;
+			break;
+		}
+
+		/* Protection flags */
+		if (pl08x->pd->memcpy_prot_buff)
+			val |= FTDMAC020_CH_CSR_PROT2;
+		if (pl08x->pd->memcpy_prot_cache)
+			val |= FTDMAC020_CH_CSR_PROT3;
+		/* We are the kernel, so we are in privileged mode */
+		val |= FTDMAC020_CH_CSR_PROT1;
+
+		writel_relaxed(val, phychan->reg_control);
+	} else {
+		/* Bits are just identical */
+		writel_relaxed(lli[PL080_LLI_CCTL], phychan->reg_control);
+	}
 
+	/* Second control word on the PL080s */
 	if (pl08x->vd->pl080s)
 		writel_relaxed(lli[PL080S_LLI_CCTL2],
 				phychan->base + PL080S_CH_CONTROL2);
@@ -423,11 +558,25 @@ static void pl08x_start_next_txd(struct pl08x_dma_chan *plchan)
 		cpu_relax();
 
 	/* Do not access config register until channel shows as inactive */
-	val = readl(phychan->reg_config);
-	while ((val & PL080_CONFIG_ACTIVE) || (val & PL080_CONFIG_ENABLE))
+	if (phychan->ftdmac020) {
+		val = readl(phychan->reg_config);
+		while (val & FTDMAC020_CH_CFG_BUSY)
+			val = readl(phychan->reg_config);
+
+		val = readl(phychan->reg_control);
+		while (val & FTDMAC020_CH_CSR_EN)
+			val = readl(phychan->reg_control);
+
+		writel(val | FTDMAC020_CH_CSR_EN,
+		       phychan->reg_control);
+	} else {
 		val = readl(phychan->reg_config);
+		while ((val & PL080_CONFIG_ACTIVE) ||
+		       (val & PL080_CONFIG_ENABLE))
+			val = readl(phychan->reg_config);
 
-	writel(val | PL080_CONFIG_ENABLE, phychan->reg_config);
+		writel(val | PL080_CONFIG_ENABLE, phychan->reg_config);
+	}
 }
 
 /*
@@ -445,6 +594,14 @@ static void pl08x_pause_phy_chan(struct pl08x_phy_chan *ch)
 	u32 val;
 	int timeout;
 
+	if (ch->ftdmac020) {
+		/* Use the enable bit on the FTDMAC020 */
+		val = readl(ch->reg_control);
+		val &= ~FTDMAC020_CH_CSR_EN;
+		writel(val, ch->reg_control);
+		return;
+	}
+
 	/* Set the HALT bit and wait for the FIFO to drain */
 	val = readl(ch->reg_config);
 	val |= PL080_CONFIG_HALT;
@@ -464,6 +621,14 @@ static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
 {
 	u32 val;
 
+	/* Use the enable bit on the FTDMAC020 */
+	if (ch->ftdmac020) {
+		val = readl(ch->reg_control);
+		val |= FTDMAC020_CH_CSR_EN;
+		writel(val, ch->reg_control);
+		return;
+	}
+
 	/* Clear the HALT bit */
 	val = readl(ch->reg_config);
 	val &= ~PL080_CONFIG_HALT;
@@ -479,25 +644,68 @@ static void pl08x_resume_phy_chan(struct pl08x_phy_chan *ch)
 static void pl08x_terminate_phy_chan(struct pl08x_driver_data *pl08x,
 	struct pl08x_phy_chan *ch)
 {
-	u32 val = readl(ch->reg_config);
+	u32 val;
 
+	/* The layout for the FTDMAC020 is different */
+	if (ch->ftdmac020) {
+		/* Disable all interrupts */
+		val = readl(ch->reg_config);
+		val |= (FTDMAC020_CH_CFG_INT_ABT_MASK |
+			FTDMAC020_CH_CFG_INT_ERR_MASK |
+			FTDMAC020_CH_CFG_INT_TC_MASK);
+		writel(val, ch->reg_config);
+
+		/* Abort and disable channel */
+		val = readl(ch->reg_control);
+		val &= ~FTDMAC020_CH_CSR_EN;
+		val |= FTDMAC020_CH_CSR_ABT;
+		writel(val, ch->reg_control);
+
+		/* Clear ABT and ERR interrupt flags */
+		writel(BIT(ch->id) | BIT(ch->id + 16),
+		       pl08x->base + PL080_ERR_CLEAR);
+		writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
+
+		return;
+	}
+
+	val = readl(ch->reg_config);
 	val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
 		 PL080_CONFIG_TC_IRQ_MASK);
-
 	writel(val, ch->reg_config);
 
 	writel(BIT(ch->id), pl08x->base + PL080_ERR_CLEAR);
 	writel(BIT(ch->id), pl08x->base + PL080_TC_CLEAR);
 }
 
-static inline u32 get_bytes_in_cctl(u32 cctl)
+static u32 get_bytes_in_phy_channel(struct pl08x_phy_chan *ch)
 {
-	/* The source width defines the number of bytes */
-	u32 bytes = cctl & PL080_CONTROL_TRANSFER_SIZE_MASK;
+	u32 val;
+	u32 bytes;
+
+	if (ch->ftdmac020) {
+		bytes = readl(ch->base + FTDMAC020_CH_SIZE);
 
-	cctl &= PL080_CONTROL_SWIDTH_MASK;
+		val = readl(ch->reg_control);
+		val &= FTDMAC020_CH_CSR_SRC_WIDTH_MSK;
+		val >>= FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT;
+	} else if (ch->pl080s) {
+		val = readl(ch->base + PL080S_CH_CONTROL2);
+		bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
 
-	switch (cctl >> PL080_CONTROL_SWIDTH_SHIFT) {
+		val = readl(ch->reg_control);
+		val &= PL080_CONTROL_SWIDTH_MASK;
+		val >>= PL080_CONTROL_SWIDTH_SHIFT;
+	} else {
+		/* Plain PL08x */
+		val = readl(ch->reg_control);
+		bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
+
+		val &= PL080_CONTROL_SWIDTH_MASK;
+		val >>= PL080_CONTROL_SWIDTH_SHIFT;
+	}
+
+	switch (val) {
 	case PL080_WIDTH_8BIT:
 		break;
 	case PL080_WIDTH_16BIT:
@@ -510,14 +718,35 @@ static inline u32 get_bytes_in_cctl(u32 cctl)
 	return bytes;
 }
 
-static inline u32 get_bytes_in_cctl_pl080s(u32 cctl, u32 cctl1)
+static u32 get_bytes_in_lli(struct pl08x_phy_chan *ch, const u32 *llis_va)
 {
-	/* The source width defines the number of bytes */
-	u32 bytes = cctl1 & PL080S_CONTROL_TRANSFER_SIZE_MASK;
+	u32 val;
+	u32 bytes;
+
+	if (ch->ftdmac020) {
+		val = llis_va[PL080_LLI_CCTL];
+		bytes = val & FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+
+		val = llis_va[PL080_LLI_CCTL];
+		val &= FTDMAC020_LLI_SRC_WIDTH_MSK;
+		val >>= FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+	} else if (ch->pl080s) {
+		val = llis_va[PL080S_LLI_CCTL2];
+		bytes = val & PL080S_CONTROL_TRANSFER_SIZE_MASK;
+
+		val = llis_va[PL080_LLI_CCTL];
+		val &= PL080_CONTROL_SWIDTH_MASK;
+		val >>= PL080_CONTROL_SWIDTH_SHIFT;
+	} else {
+		/* Plain PL08x */
+		val = llis_va[PL080_LLI_CCTL];
+		bytes = val & PL080_CONTROL_TRANSFER_SIZE_MASK;
 
-	cctl &= PL080_CONTROL_SWIDTH_MASK;
+		val &= PL080_CONTROL_SWIDTH_MASK;
+		val >>= PL080_CONTROL_SWIDTH_SHIFT;
+	}
 
-	switch (cctl >> PL080_CONTROL_SWIDTH_SHIFT) {
+	switch (val) {
 	case PL080_WIDTH_8BIT:
 		break;
 	case PL080_WIDTH_16BIT:
@@ -552,15 +781,10 @@ static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
 	 * Follow the LLIs to get the number of remaining
 	 * bytes in the currently active transaction.
 	 */
-	clli = readl(ch->base + PL080_CH_LLI) & ~PL080_LLI_LM_AHB2;
+	clli = readl(ch->reg_lli) & ~PL080_LLI_LM_AHB2;
 
 	/* First get the remaining bytes in the active transfer */
-	if (pl08x->vd->pl080s)
-		bytes = get_bytes_in_cctl_pl080s(
-				readl(ch->base + PL080_CH_CONTROL),
-				readl(ch->base + PL080S_CH_CONTROL2));
-	else
-		bytes = get_bytes_in_cctl(readl(ch->base + PL080_CH_CONTROL));
+	bytes = get_bytes_in_phy_channel(ch);
 
 	if (!clli)
 		return bytes;
@@ -581,12 +805,7 @@ static u32 pl08x_getbytes_chan(struct pl08x_dma_chan *plchan)
 	llis_va_limit = llis_va + llis_max_words;
 
 	for (; llis_va < llis_va_limit; llis_va += pl08x->lli_words) {
-		if (pl08x->vd->pl080s)
-			bytes += get_bytes_in_cctl_pl080s(
-						llis_va[PL080_LLI_CCTL],
-						llis_va[PL080S_LLI_CCTL2]);
-		else
-			bytes += get_bytes_in_cctl(llis_va[PL080_LLI_CCTL]);
+		bytes += get_bytes_in_lli(ch, llis_va);
 
 		/*
 		 * A LLI pointer going backward terminates the LLI list
@@ -705,7 +924,7 @@ static void pl08x_phy_free(struct pl08x_dma_chan *plchan)
 			break;
 		}
 
-	if (!next) {
+	if (!next && pl08x->has_slave) {
 		list_for_each_entry(p, &pl08x->slave.channels, vc.chan.device_node)
 			if (p->state == PL08X_CHAN_WAITING) {
 				next = p;
@@ -746,9 +965,30 @@ static void pl08x_phy_free(struct pl08x_dma_chan *plchan)
  * LLI handling
  */
 
-static inline unsigned int pl08x_get_bytes_for_cctl(unsigned int coded)
+static inline unsigned int
+pl08x_get_bytes_for_lli(struct pl08x_driver_data *pl08x,
+			u32 cctl,
+			bool source)
 {
-	switch (coded) {
+	u32 val;
+
+	if (pl08x->vd->ftdmac020) {
+		if (source)
+			val = (cctl & FTDMAC020_LLI_SRC_WIDTH_MSK) >>
+				FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+		else
+			val = (cctl & FTDMAC020_LLI_DST_WIDTH_MSK) >>
+				FTDMAC020_LLI_DST_WIDTH_SHIFT;
+	} else {
+		if (source)
+			val = (cctl & PL080_CONTROL_SWIDTH_MASK) >>
+				PL080_CONTROL_SWIDTH_SHIFT;
+		else
+			val = (cctl & PL080_CONTROL_DWIDTH_MASK) >>
+				PL080_CONTROL_DWIDTH_SHIFT;
+	}
+
+	switch (val) {
 	case PL080_WIDTH_8BIT:
 		return 1;
 	case PL080_WIDTH_16BIT:
@@ -762,49 +1002,106 @@ static inline unsigned int pl08x_get_bytes_for_cctl(unsigned int coded)
 	return 0;
 }
 
-static inline u32 pl08x_cctl_bits(u32 cctl, u8 srcwidth, u8 dstwidth,
-				  size_t tsize)
+static inline u32 pl08x_lli_control_bits(struct pl08x_driver_data *pl08x,
+					 u32 cctl,
+					 u8 srcwidth, u8 dstwidth,
+					 size_t tsize)
 {
 	u32 retbits = cctl;
 
-	/* Remove all src, dst and transfer size bits */
-	retbits &= ~PL080_CONTROL_DWIDTH_MASK;
-	retbits &= ~PL080_CONTROL_SWIDTH_MASK;
-	retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
+	/*
+	 * Remove all src, dst and transfer size bits, then set the
+	 * width and size according to the parameters. The bit offsets
+	 * are different in the FTDMAC020 so we need to accound for this.
+	 */
+	if (pl08x->vd->ftdmac020) {
+		retbits &= ~FTDMAC020_LLI_DST_WIDTH_MSK;
+		retbits &= ~FTDMAC020_LLI_SRC_WIDTH_MSK;
+		retbits &= ~FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+
+		switch (srcwidth) {
+		case 1:
+			retbits |= PL080_WIDTH_8BIT <<
+				FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+			break;
+		case 2:
+			retbits |= PL080_WIDTH_16BIT <<
+				FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+			break;
+		case 4:
+			retbits |= PL080_WIDTH_32BIT <<
+				FTDMAC020_LLI_SRC_WIDTH_SHIFT;
+			break;
+		default:
+			BUG();
+			break;
+		}
 
-	/* Then set the bits according to the parameters */
-	switch (srcwidth) {
-	case 1:
-		retbits |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT;
-		break;
-	case 2:
-		retbits |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT;
-		break;
-	case 4:
-		retbits |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT;
-		break;
-	default:
-		BUG();
-		break;
-	}
+		switch (dstwidth) {
+		case 1:
+			retbits |= PL080_WIDTH_8BIT <<
+				FTDMAC020_LLI_DST_WIDTH_SHIFT;
+			break;
+		case 2:
+			retbits |= PL080_WIDTH_16BIT <<
+				FTDMAC020_LLI_DST_WIDTH_SHIFT;
+			break;
+		case 4:
+			retbits |= PL080_WIDTH_32BIT <<
+				FTDMAC020_LLI_DST_WIDTH_SHIFT;
+			break;
+		default:
+			BUG();
+			break;
+		}
 
-	switch (dstwidth) {
-	case 1:
-		retbits |= PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
-		break;
-	case 2:
-		retbits |= PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
-		break;
-	case 4:
-		retbits |= PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
-		break;
-	default:
-		BUG();
-		break;
+		tsize &= FTDMAC020_LLI_TRANSFER_SIZE_MASK;
+		retbits |= tsize << FTDMAC020_LLI_TRANSFER_SIZE_SHIFT;
+	} else {
+		retbits &= ~PL080_CONTROL_DWIDTH_MASK;
+		retbits &= ~PL080_CONTROL_SWIDTH_MASK;
+		retbits &= ~PL080_CONTROL_TRANSFER_SIZE_MASK;
+
+		switch (srcwidth) {
+		case 1:
+			retbits |= PL080_WIDTH_8BIT <<
+				PL080_CONTROL_SWIDTH_SHIFT;
+			break;
+		case 2:
+			retbits |= PL080_WIDTH_16BIT <<
+				PL080_CONTROL_SWIDTH_SHIFT;
+			break;
+		case 4:
+			retbits |= PL080_WIDTH_32BIT <<
+				PL080_CONTROL_SWIDTH_SHIFT;
+			break;
+		default:
+			BUG();
+			break;
+		}
+
+		switch (dstwidth) {
+		case 1:
+			retbits |= PL080_WIDTH_8BIT <<
+				PL080_CONTROL_DWIDTH_SHIFT;
+			break;
+		case 2:
+			retbits |= PL080_WIDTH_16BIT <<
+				PL080_CONTROL_DWIDTH_SHIFT;
+			break;
+		case 4:
+			retbits |= PL080_WIDTH_32BIT <<
+				PL080_CONTROL_DWIDTH_SHIFT;
+			break;
+		default:
+			BUG();
+			break;
+		}
+
+		tsize &= PL080_CONTROL_TRANSFER_SIZE_MASK;
+		retbits |= tsize << PL080_CONTROL_TRANSFER_SIZE_SHIFT;
 	}
 
-	tsize &= PL080_CONTROL_TRANSFER_SIZE_MASK;
-	retbits |= tsize << PL080_CONTROL_TRANSFER_SIZE_SHIFT;
 	return retbits;
 }
 
@@ -825,13 +1122,35 @@ struct pl08x_lli_build_data {
  * - prefers the destination bus if both available
  * - prefers bus with fixed address (i.e. peripheral)
  */
-static void pl08x_choose_master_bus(struct pl08x_lli_build_data *bd,
-	struct pl08x_bus_data **mbus, struct pl08x_bus_data **sbus, u32 cctl)
+static void pl08x_choose_master_bus(struct pl08x_driver_data *pl08x,
+				    struct pl08x_lli_build_data *bd,
+				    struct pl08x_bus_data **mbus,
+				    struct pl08x_bus_data **sbus,
+				    u32 cctl)
 {
-	if (!(cctl & PL080_CONTROL_DST_INCR)) {
+	bool dst_incr;
+	bool src_incr;
+
+	/*
+	 * The FTDMAC020 only supports memory-to-memory transfer, so
+	 * source and destination always increase.
+	 */
+	if (pl08x->vd->ftdmac020) {
+		dst_incr = true;
+		src_incr = true;
+	} else {
+		dst_incr = !!(cctl & PL080_CONTROL_DST_INCR);
+		src_incr = !!(cctl & PL080_CONTROL_SRC_INCR);
+	}
+
+	/*
+	 * If either bus is not advancing, i.e. it is a peripheral, that
+	 * one becomes master
+	 */
+	if (!dst_incr) {
 		*mbus = &bd->dstbus;
 		*sbus = &bd->srcbus;
-	} else if (!(cctl & PL080_CONTROL_SRC_INCR)) {
+	} else if (!src_incr) {
 		*mbus = &bd->srcbus;
 		*sbus = &bd->dstbus;
 	} else {
@@ -869,10 +1188,16 @@ static void pl08x_fill_lli_for_desc(struct pl08x_driver_data *pl08x,
 	if (pl08x->vd->pl080s)
 		llis_va[PL080S_LLI_CCTL2] = cctl2;
 
-	if (cctl & PL080_CONTROL_SRC_INCR)
+	if (pl08x->vd->ftdmac020) {
+		/* FIXME: only memcpy so far so both increase */
 		bd->srcbus.addr += len;
-	if (cctl & PL080_CONTROL_DST_INCR)
 		bd->dstbus.addr += len;
+	} else {
+		if (cctl & PL080_CONTROL_SRC_INCR)
+			bd->srcbus.addr += len;
+		if (cctl & PL080_CONTROL_DST_INCR)
+			bd->dstbus.addr += len;
+	}
 
 	BUG_ON(bd->remainder < len);
 
@@ -883,12 +1208,12 @@ static inline void prep_byte_width_lli(struct pl08x_driver_data *pl08x,
 			struct pl08x_lli_build_data *bd, u32 *cctl, u32 len,
 			int num_llis, size_t *total_bytes)
 {
-	*cctl = pl08x_cctl_bits(*cctl, 1, 1, len);
+	*cctl = pl08x_lli_control_bits(pl08x, *cctl, 1, 1, len);
 	pl08x_fill_lli_for_desc(pl08x, bd, num_llis, len, *cctl, len);
 	(*total_bytes) += len;
 }
 
-#ifdef VERBOSE_DEBUG
+#if 1
 static void pl08x_dump_lli(struct pl08x_driver_data *pl08x,
 			   const u32 *llis_va, int num_llis)
 {
@@ -953,14 +1278,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 	cctl = txd->cctl;
 
 	/* Find maximum width of the source bus */
-	bd.srcbus.maxwidth =
-		pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_SWIDTH_MASK) >>
-				       PL080_CONTROL_SWIDTH_SHIFT);
+	bd.srcbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, true);
 
 	/* Find maximum width of the destination bus */
-	bd.dstbus.maxwidth =
-		pl08x_get_bytes_for_cctl((cctl & PL080_CONTROL_DWIDTH_MASK) >>
-				       PL080_CONTROL_DWIDTH_SHIFT);
+	bd.dstbus.maxwidth = pl08x_get_bytes_for_lli(pl08x, cctl, false);
 
 	list_for_each_entry(dsg, &txd->dsg_list, node) {
 		total_bytes = 0;
@@ -972,7 +1293,7 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 		bd.srcbus.buswidth = bd.srcbus.maxwidth;
 		bd.dstbus.buswidth = bd.dstbus.maxwidth;
 
-		pl08x_choose_master_bus(&bd, &mbus, &sbus, cctl);
+		pl08x_choose_master_bus(pl08x, &bd, &mbus, &sbus, cctl);
 
 		dev_vdbg(&pl08x->adev->dev,
 			"src=0x%08llx%s/%u dst=0x%08llx%s/%u len=%zu\n",
@@ -1009,8 +1330,14 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 		 *   supported. Thus, we can't have scattered addresses.
 		 */
 		if (!bd.remainder) {
-			u32 fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >>
-				PL080_CONFIG_FLOW_CONTROL_SHIFT;
+			u32 fc;
+
+			/* FTDMAC020 only does memory-to-memory */
+			if (pl08x->vd->ftdmac020)
+				fc = PL080_FLOW_MEM2MEM;
+			else
+				fc = (txd->ccfg & PL080_CONFIG_FLOW_CONTROL_MASK) >>
+					PL080_CONFIG_FLOW_CONTROL_SHIFT;
 			if (!((fc >= PL080_FLOW_SRC2DST_DST) &&
 					(fc <= PL080_FLOW_SRC2DST_SRC))) {
 				dev_err(&pl08x->adev->dev, "%s sg len can't be zero",
@@ -1027,8 +1354,9 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 				return 0;
 			}
 
-			cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth,
-					bd.dstbus.buswidth, 0);
+			cctl = pl08x_lli_control_bits(pl08x, cctl,
+					bd.srcbus.buswidth, bd.dstbus.buswidth,
+					0);
 			pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
 					0, cctl, 0);
 			break;
@@ -1107,8 +1435,9 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 					"size 0x%08zx (remainder 0x%08zx)\n",
 					__func__, lli_len, bd.remainder);
 
-				cctl = pl08x_cctl_bits(cctl, bd.srcbus.buswidth,
-					bd.dstbus.buswidth, tsize);
+				cctl = pl08x_lli_control_bits(pl08x, cctl,
+					bd.srcbus.buswidth, bd.dstbus.buswidth,
+					tsize);
 				pl08x_fill_lli_for_desc(pl08x, &bd, num_llis++,
 						lli_len, cctl, tsize);
 				total_bytes += lli_len;
@@ -1151,7 +1480,10 @@ static int pl08x_fill_llis_for_desc(struct pl08x_driver_data *pl08x,
 		/* The final LLI terminates the LLI. */
 		last_lli[PL080_LLI_LLI] = 0;
 		/* The final LLI element shall also fire an interrupt. */
-		last_lli[PL080_LLI_CCTL] |= PL080_CONTROL_TC_IRQ_EN;
+		if (pl08x->vd->ftdmac020)
+			last_lli[PL080_LLI_CCTL] &= ~FTDMAC020_LLI_TC_MSK;
+		else
+			last_lli[PL080_LLI_CCTL] |= PL080_CONTROL_TC_IRQ_EN;
 	}
 
 	pl08x_dump_lli(pl08x, llis_va, num_llis);
@@ -1317,14 +1649,25 @@ static const struct burst_table burst_sizes[] = {
  * will be routed to each port.  We try to have source and destination
  * on separate ports, but always respect the allowable settings.
  */
-static u32 pl08x_select_bus(u8 src, u8 dst)
+static u32 pl08x_select_bus(bool ftdmac020, u8 src, u8 dst)
 {
 	u32 cctl = 0;
+	u32 dst_ahb2;
+	u32 src_ahb2;
+
+	/* The FTDMAC020 use different bits to indicate src/dst bus */
+	if (ftdmac020) {
+		dst_ahb2 = FTDMAC020_LLI_DST_SEL;
+		src_ahb2 = FTDMAC020_LLI_SRC_SEL;
+	} else {
+		dst_ahb2 = PL080_CONTROL_DST_AHB2;
+		src_ahb2 = PL080_CONTROL_SRC_AHB2;
+	}
 
 	if (!(dst & PL08X_AHB1) || ((dst & PL08X_AHB2) && (src & PL08X_AHB1)))
-		cctl |= PL080_CONTROL_DST_AHB2;
+		cctl |= dst_ahb2;
 	if (!(src & PL08X_AHB1) || ((src & PL08X_AHB2) && !(dst & PL08X_AHB2)))
-		cctl |= PL080_CONTROL_SRC_AHB2;
+		cctl |= src_ahb2;
 
 	return cctl;
 }
@@ -1412,14 +1755,134 @@ static struct pl08x_txd *pl08x_get_txd(struct pl08x_dma_chan *plchan)
 {
 	struct pl08x_txd *txd = kzalloc(sizeof(*txd), GFP_NOWAIT);
 
-	if (txd) {
+	if (txd)
 		INIT_LIST_HEAD(&txd->dsg_list);
+	return txd;
+}
 
-		/* Always enable error and terminal interrupts */
-		txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
-			    PL080_CONFIG_TC_IRQ_MASK;
+static u32 pl08x_memcpy_cctl(struct pl08x_driver_data *pl08x)
+{
+	u32 cctl = 0;
+
+	/* Conjure cctl */
+	switch (pl08x->pd->memcpy_burst_size) {
+	default:
+		dev_err(&pl08x->adev->dev,
+			"illegal burst size for memcpy, set to 1\n");
+		/* Fall through */
+	case PL08X_BURST_SZ_1:
+		cctl |= PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_4:
+		cctl |= PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_8:
+		cctl |= PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_16:
+		cctl |= PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_32:
+		cctl |= PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_64:
+		cctl |= PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_128:
+		cctl |= PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
+	case PL08X_BURST_SZ_256:
+		cctl |= PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT |
+			PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT;
+		break;
 	}
-	return txd;
+
+	switch (pl08x->pd->memcpy_bus_width) {
+	default:
+		dev_err(&pl08x->adev->dev,
+			"illegal bus width for memcpy, set to 8 bits\n");
+		/* Fall through */
+	case PL08X_BUS_WIDTH_8_BITS:
+		cctl |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT |
+			PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		break;
+	case PL08X_BUS_WIDTH_16_BITS:
+		cctl |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT |
+			PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		break;
+	case PL08X_BUS_WIDTH_32_BITS:
+		cctl |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
+			PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		break;
+	}
+
+	/* Protection flags */
+	if (pl08x->pd->memcpy_prot_buff)
+		cctl |= PL080_CONTROL_PROT_BUFF;
+	if (pl08x->pd->memcpy_prot_cache)
+		cctl |= PL080_CONTROL_PROT_CACHE;
+
+	/* We are the kernel, so we are in privileged mode */
+	cctl |= PL080_CONTROL_PROT_SYS;
+
+	/* Both to be incremented or the code will break */
+	cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
+
+	if (pl08x->vd->dualmaster)
+		cctl |= pl08x_select_bus(false,
+					 pl08x->mem_buses,
+					 pl08x->mem_buses);
+
+	return cctl;
+}
+
+static u32 pl08x_ftdmac020_memcpy_cctl(struct pl08x_driver_data *pl08x)
+{
+	u32 cctl = 0;
+
+	/* Conjure cctl */
+	switch (pl08x->pd->memcpy_bus_width) {
+	default:
+		dev_err(&pl08x->adev->dev,
+			"illegal bus width for memcpy, set to 8 bits\n");
+		/* Fall through */
+	case PL08X_BUS_WIDTH_8_BITS:
+		cctl |= PL080_WIDTH_8BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+			PL080_WIDTH_8BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+		break;
+	case PL08X_BUS_WIDTH_16_BITS:
+		cctl |= PL080_WIDTH_16BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+			PL080_WIDTH_16BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+		break;
+	case PL08X_BUS_WIDTH_32_BITS:
+		cctl |= PL080_WIDTH_32BIT << FTDMAC020_LLI_SRC_WIDTH_SHIFT |
+			PL080_WIDTH_32BIT << FTDMAC020_LLI_DST_WIDTH_SHIFT;
+		break;
+	}
+
+	/*
+	 * By default mask the TC IRQ on all LLIs, it will be unmasked on
+	 * the last LLI item by other code.
+	 */
+	cctl |= FTDMAC020_LLI_TC_MSK;
+
+	/*
+	 * Both to be incremented so leave bits FTDMAC020_LLI_SRCAD_CTL
+	 * and FTDMAC020_LLI_DSTAD_CTL as zero
+	 */
+	if (pl08x->vd->dualmaster)
+		cctl |= pl08x_select_bus(true,
+					 pl08x->mem_buses,
+					 pl08x->mem_buses);
+
+	return cctl;
 }
 
 /*
@@ -1452,18 +1915,16 @@ static struct dma_async_tx_descriptor *pl08x_prep_dma_memcpy(
 	dsg->src_addr = src;
 	dsg->dst_addr = dest;
 	dsg->len = len;
-
-	/* Set platform data for m2m */
-	txd->ccfg |= PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
-	txd->cctl = pl08x->pd->memcpy_channel.cctl_memcpy &
-			~(PL080_CONTROL_DST_AHB2 | PL080_CONTROL_SRC_AHB2);
-
-	/* Both to be incremented or the code will break */
-	txd->cctl |= PL080_CONTROL_SRC_INCR | PL080_CONTROL_DST_INCR;
-
-	if (pl08x->vd->dualmaster)
-		txd->cctl |= pl08x_select_bus(pl08x->mem_buses,
-					      pl08x->mem_buses);
+	if (pl08x->vd->ftdmac020) {
+		/* Writing CCFG zero ENABLES all interrupts */
+		txd->ccfg = 0;
+		txd->cctl = pl08x_ftdmac020_memcpy_cctl(pl08x);
+	} else {
+		txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
+			PL080_CONFIG_TC_IRQ_MASK |
+			PL080_FLOW_MEM2MEM << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+		txd->cctl = pl08x_memcpy_cctl(pl08x);
+	}
 
 	ret = pl08x_fill_llis_for_desc(plchan->host, txd);
 	if (!ret) {
@@ -1527,7 +1988,7 @@ static struct pl08x_txd *pl08x_init_txd(
 		return NULL;
 	}
 
-	txd->cctl = cctl | pl08x_select_bus(src_buses, dst_buses);
+	txd->cctl = cctl | pl08x_select_bus(false, src_buses, dst_buses);
 
 	if (plchan->cfg.device_fc)
 		tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER_PER :
@@ -1536,7 +1997,9 @@ static struct pl08x_txd *pl08x_init_txd(
 		tmp = (direction == DMA_MEM_TO_DEV) ? PL080_FLOW_MEM2PER :
 			PL080_FLOW_PER2MEM;
 
-	txd->ccfg |= tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT;
+	txd->ccfg = PL080_CONFIG_ERR_IRQ_MASK |
+		PL080_CONFIG_TC_IRQ_MASK |
+		tmp << PL080_CONFIG_FLOW_CONTROL_SHIFT;
 
 	ret = pl08x_request_mux(plchan);
 	if (ret < 0) {
@@ -1813,6 +2276,11 @@ static void pl08x_ensure_on(struct pl08x_driver_data *pl08x)
 	/* The Nomadik variant does not have the config register */
 	if (pl08x->vd->nomadik)
 		return;
+	/* The FTDMAC020 variant does this in another register */
+	if (pl08x->vd->ftdmac020) {
+		writel(PL080_CONFIG_ENABLE, pl08x->base + FTDMAC020_CSR);
+		return;
+	}
 	writel(PL080_CONFIG_ENABLE, pl08x->base + PL080_CONFIG);
 }
 
@@ -1925,9 +2393,16 @@ static int pl08x_dma_init_virtual_channels(struct pl08x_driver_data *pl08x,
 			chan->signal = i;
 			pl08x_dma_slave_init(chan);
 		} else {
-			chan->cd = &pl08x->pd->memcpy_channel;
+			chan->cd = kzalloc(sizeof(*chan->cd), GFP_KERNEL);
+			if (!chan->cd) {
+				kfree(chan);
+				return -ENOMEM;
+			}
+			chan->cd->bus_id = "memcpy";
+			chan->cd->periph_buses = pl08x->pd->mem_buses;
 			chan->name = kasprintf(GFP_KERNEL, "memcpy%d", i);
 			if (!chan->name) {
+				kfree(chan->cd);
 				kfree(chan);
 				return -ENOMEM;
 			}
@@ -2009,12 +2484,15 @@ static int pl08x_debugfs_show(struct seq_file *s, void *data)
 			   pl08x_state_str(chan->state));
 	}
 
-	seq_printf(s, "\nPL08x virtual slave channels:\n");
-	seq_printf(s, "CHANNEL:\tSTATE:\n");
-	seq_printf(s, "--------\t------\n");
-	list_for_each_entry(chan, &pl08x->slave.channels, vc.chan.device_node) {
-		seq_printf(s, "%s\t\t%s\n", chan->name,
-			   pl08x_state_str(chan->state));
+	if (pl08x->has_slave) {
+		seq_printf(s, "\nPL08x virtual slave channels:\n");
+		seq_printf(s, "CHANNEL:\tSTATE:\n");
+		seq_printf(s, "--------\t------\n");
+		list_for_each_entry(chan, &pl08x->slave.channels,
+				    vc.chan.device_node) {
+			seq_printf(s, "%s\t\t%s\n", chan->name,
+				   pl08x_state_str(chan->state));
+		}
 	}
 
 	return 0;
@@ -2052,6 +2530,10 @@ static struct dma_chan *pl08x_find_chan_id(struct pl08x_driver_data *pl08x,
 {
 	struct pl08x_dma_chan *chan;
 
+	/* Trying to get a slave channel from something with no slave support */
+	if (!pl08x->has_slave)
+		return NULL;
+
 	list_for_each_entry(chan, &pl08x->slave.channels, vc.chan.device_node) {
 		if (chan->signal == id)
 			return &chan->vc.chan;
@@ -2099,7 +2581,6 @@ static int pl08x_of_probe(struct amba_device *adev,
 {
 	struct pl08x_platform_data *pd;
 	struct pl08x_channel_data *chanp = NULL;
-	u32 cctl_memcpy = 0;
 	u32 val;
 	int ret;
 	int i;
@@ -2139,36 +2620,28 @@ static int pl08x_of_probe(struct amba_device *adev,
 		dev_err(&adev->dev, "illegal burst size for memcpy, set to 1\n");
 		/* Fall through */
 	case 1:
-		cctl_memcpy |= PL080_BSIZE_1 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_1 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_1;
 		break;
 	case 4:
-		cctl_memcpy |= PL080_BSIZE_4 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_4 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_4;
 		break;
 	case 8:
-		cctl_memcpy |= PL080_BSIZE_8 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_8 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_8;
 		break;
 	case 16:
-		cctl_memcpy |= PL080_BSIZE_16 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_16 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_16;
 		break;
 	case 32:
-		cctl_memcpy |= PL080_BSIZE_32 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_32 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_32;
 		break;
 	case 64:
-		cctl_memcpy |= PL080_BSIZE_64 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_64 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_64;
 		break;
 	case 128:
-		cctl_memcpy |= PL080_BSIZE_128 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_128 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_128;
 		break;
 	case 256:
-		cctl_memcpy |= PL080_BSIZE_256 << PL080_CONTROL_SB_SIZE_SHIFT |
-			       PL080_BSIZE_256 << PL080_CONTROL_DB_SIZE_SHIFT;
+		pd->memcpy_burst_size = PL08X_BURST_SZ_256;
 		break;
 	}
 
@@ -2182,48 +2655,40 @@ static int pl08x_of_probe(struct amba_device *adev,
 		dev_err(&adev->dev, "illegal bus width for memcpy, set to 8 bits\n");
 		/* Fall through */
 	case 8:
-		cctl_memcpy |= PL080_WIDTH_8BIT << PL080_CONTROL_SWIDTH_SHIFT |
-			       PL080_WIDTH_8BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		pd->memcpy_bus_width = PL08X_BUS_WIDTH_8_BITS;
 		break;
 	case 16:
-		cctl_memcpy |= PL080_WIDTH_16BIT << PL080_CONTROL_SWIDTH_SHIFT |
-			       PL080_WIDTH_16BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		pd->memcpy_bus_width = PL08X_BUS_WIDTH_16_BITS;
 		break;
 	case 32:
-		cctl_memcpy |= PL080_WIDTH_32BIT << PL080_CONTROL_SWIDTH_SHIFT |
-			       PL080_WIDTH_32BIT << PL080_CONTROL_DWIDTH_SHIFT;
+		pd->memcpy_bus_width = PL08X_BUS_WIDTH_32_BITS;
 		break;
 	}
 
-	/* This is currently the only thing making sense */
-	cctl_memcpy |= PL080_CONTROL_PROT_SYS;
-
-	/* Set up memcpy channel */
-	pd->memcpy_channel.bus_id = "memcpy";
-	pd->memcpy_channel.cctl_memcpy = cctl_memcpy;
-	/* Use the buses that can access memory, obviously */
-	pd->memcpy_channel.periph_buses = pd->mem_buses;
-
 	/*
 	 * Allocate channel data for all possible slave channels (one
 	 * for each possible signal), channels will then be allocated
 	 * for a device and have it's AHB interfaces set up at
 	 * translation time.
 	 */
-	chanp = devm_kcalloc(&adev->dev,
-			pl08x->vd->signals,
-			sizeof(struct pl08x_channel_data),
-			GFP_KERNEL);
-	if (!chanp)
-		return -ENOMEM;
+	if (pl08x->vd->signals) {
+		chanp = devm_kcalloc(&adev->dev,
+				     pl08x->vd->signals,
+				     sizeof(struct pl08x_channel_data),
+				     GFP_KERNEL);
+		if (!chanp)
+			return -ENOMEM;
 
-	pd->slave_channels = chanp;
-	for (i = 0; i < pl08x->vd->signals; i++) {
-		/* chanp->periph_buses will be assigned at translation */
-		chanp->bus_id = kasprintf(GFP_KERNEL, "slave%d", i);
-		chanp++;
+		pd->slave_channels = chanp;
+		for (i = 0; i < pl08x->vd->signals; i++) {
+			/*
+			 * chanp->periph_buses will be assigned at translation
+			 */
+			chanp->bus_id = kasprintf(GFP_KERNEL, "slave%d", i);
+			chanp++;
+		}
+		pd->num_slave_channels = pl08x->vd->signals;
 	}
-	pd->num_slave_channels = pl08x->vd->signals;
 
 	pl08x->pd = pd;
 
@@ -2242,7 +2707,7 @@ static inline int pl08x_of_probe(struct amba_device *adev,
 static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 {
 	struct pl08x_driver_data *pl08x;
-	const struct vendor_data *vd = id->data;
+	struct vendor_data *vd = id->data;
 	struct device_node *np = adev->dev.of_node;
 	u32 tsfr_size;
 	int ret = 0;
@@ -2268,6 +2733,34 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 	pl08x->adev = adev;
 	pl08x->vd = vd;
 
+	pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
+	if (!pl08x->base) {
+		ret = -ENOMEM;
+		goto out_no_ioremap;
+	}
+
+	if (vd->ftdmac020) {
+		u32 val;
+
+		val = readl(pl08x->base + FTDMAC020_REVISION);
+		dev_info(&pl08x->adev->dev, "FTDMAC020 %d.%d rel %d\n",
+			 (val >> 16) & 0xff, (val >> 8) & 0xff, val & 0xff);
+		val = readl(pl08x->base + FTDMAC020_FEATURE);
+		dev_info(&pl08x->adev->dev, "FTDMAC020 %d channels, "
+			 "%s built-in bridge, %s, %s linked lists\n",
+			 (val >> 12) & 0x0f,
+			 (val & BIT(10)) ? "no" : "has",
+			 (val & BIT(9)) ? "AHB0 and AHB1" : "AHB0",
+			 (val & BIT(8)) ? "supports" : "does not support");
+
+		/* Vendor data from feature register */
+		if (!(val & BIT(8)))
+			dev_warn(&pl08x->adev->dev,
+				 "linked lists not supported, required\n");
+		vd->channels = (val >> 12) & 0x0f;
+		vd->dualmaster = !!(val & BIT(9));
+	}
+
 	/* Initialize memcpy engine */
 	dma_cap_set(DMA_MEMCPY, pl08x->memcpy.cap_mask);
 	pl08x->memcpy.dev = &adev->dev;
@@ -2284,25 +2777,38 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 	pl08x->memcpy.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
 	pl08x->memcpy.directions = BIT(DMA_MEM_TO_MEM);
 	pl08x->memcpy.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
+	if (vd->ftdmac020)
+		pl08x->memcpy.copy_align = DMAENGINE_ALIGN_4_BYTES;
 
-	/* Initialize slave engine */
-	dma_cap_set(DMA_SLAVE, pl08x->slave.cap_mask);
-	dma_cap_set(DMA_CYCLIC, pl08x->slave.cap_mask);
-	pl08x->slave.dev = &adev->dev;
-	pl08x->slave.device_free_chan_resources = pl08x_free_chan_resources;
-	pl08x->slave.device_prep_dma_interrupt = pl08x_prep_dma_interrupt;
-	pl08x->slave.device_tx_status = pl08x_dma_tx_status;
-	pl08x->slave.device_issue_pending = pl08x_issue_pending;
-	pl08x->slave.device_prep_slave_sg = pl08x_prep_slave_sg;
-	pl08x->slave.device_prep_dma_cyclic = pl08x_prep_dma_cyclic;
-	pl08x->slave.device_config = pl08x_config;
-	pl08x->slave.device_pause = pl08x_pause;
-	pl08x->slave.device_resume = pl08x_resume;
-	pl08x->slave.device_terminate_all = pl08x_terminate_all;
-	pl08x->slave.src_addr_widths = PL80X_DMA_BUSWIDTHS;
-	pl08x->slave.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
-	pl08x->slave.directions = BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
-	pl08x->slave.residue_granularity = DMA_RESIDUE_GRANULARITY_SEGMENT;
+
+	/*
+	 * Initialize slave engine, if the block has no signals, that means
+	 * we have no slave support.
+	 */
+	if (vd->signals) {
+		pl08x->has_slave = true;
+		dma_cap_set(DMA_SLAVE, pl08x->slave.cap_mask);
+		dma_cap_set(DMA_CYCLIC, pl08x->slave.cap_mask);
+		pl08x->slave.dev = &adev->dev;
+		pl08x->slave.device_free_chan_resources =
+			pl08x_free_chan_resources;
+		pl08x->slave.device_prep_dma_interrupt =
+			pl08x_prep_dma_interrupt;
+		pl08x->slave.device_tx_status = pl08x_dma_tx_status;
+		pl08x->slave.device_issue_pending = pl08x_issue_pending;
+		pl08x->slave.device_prep_slave_sg = pl08x_prep_slave_sg;
+		pl08x->slave.device_prep_dma_cyclic = pl08x_prep_dma_cyclic;
+		pl08x->slave.device_config = pl08x_config;
+		pl08x->slave.device_pause = pl08x_pause;
+		pl08x->slave.device_resume = pl08x_resume;
+		pl08x->slave.device_terminate_all = pl08x_terminate_all;
+		pl08x->slave.src_addr_widths = PL80X_DMA_BUSWIDTHS;
+		pl08x->slave.dst_addr_widths = PL80X_DMA_BUSWIDTHS;
+		pl08x->slave.directions =
+			BIT(DMA_DEV_TO_MEM) | BIT(DMA_MEM_TO_DEV);
+		pl08x->slave.residue_granularity =
+			DMA_RESIDUE_GRANULARITY_SEGMENT;
+	}
 
 	/* Get the platform data */
 	pl08x->pd = dev_get_platdata(&adev->dev);
@@ -2344,19 +2850,18 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 		goto out_no_lli_pool;
 	}
 
-	pl08x->base = ioremap(adev->res.start, resource_size(&adev->res));
-	if (!pl08x->base) {
-		ret = -ENOMEM;
-		goto out_no_ioremap;
-	}
-
 	/* Turn on the PL08x */
 	pl08x_ensure_on(pl08x);
 
-	/* Attach the interrupt handler */
-	writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
+	/* Clear any pending interrupts */
+	if (vd->ftdmac020)
+		/* This variant has error IRQs in bits 16-19 */
+		writel(0x0000FFFF, pl08x->base + PL080_ERR_CLEAR);
+	else
+		writel(0x000000FF, pl08x->base + PL080_ERR_CLEAR);
 	writel(0x000000FF, pl08x->base + PL080_TC_CLEAR);
 
+	/* Attach the interrupt handler */
 	ret = request_irq(adev->irq[0], pl08x_irq, 0, DRIVER_NAME, pl08x);
 	if (ret) {
 		dev_err(&adev->dev, "%s failed to request interrupt %d\n",
@@ -2377,7 +2882,25 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 
 		ch->id = i;
 		ch->base = pl08x->base + PL080_Cx_BASE(i);
-		ch->reg_config = ch->base + vd->config_offset;
+		if (vd->ftdmac020) {
+			/* FTDMA020 has a special channel busy register */
+			ch->reg_busy = ch->base + FTDMAC020_CH_BUSY;
+			ch->reg_config = ch->base + FTDMAC020_CH_CFG;
+			ch->reg_control = ch->base + FTDMAC020_CH_CSR;
+			ch->reg_src = ch->base + FTDMAC020_CH_SRC_ADDR;
+			ch->reg_dst = ch->base + FTDMAC020_CH_DST_ADDR;
+			ch->reg_lli = ch->base + FTDMAC020_CH_LLP;
+			ch->ftdmac020 = true;
+		} else {
+			ch->reg_config = ch->base + vd->config_offset;
+			ch->reg_control = ch->base + PL080_CH_CONTROL;
+			ch->reg_src = ch->base + PL080_CH_SRC_ADDR;
+			ch->reg_dst = ch->base + PL080_CH_DST_ADDR;
+			ch->reg_lli = ch->base + PL080_CH_LLI;
+		}
+		if (vd->pl080s)
+			ch->pl080s = true;
+
 		spin_lock_init(&ch->lock);
 
 		/*
@@ -2410,13 +2933,15 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 	}
 
 	/* Register slave channels */
-	ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->slave,
-			pl08x->pd->num_slave_channels, true);
-	if (ret < 0) {
-		dev_warn(&pl08x->adev->dev,
-			"%s failed to enumerate slave channels - %d\n",
-				__func__, ret);
-		goto out_no_slave;
+	if (pl08x->has_slave) {
+		ret = pl08x_dma_init_virtual_channels(pl08x, &pl08x->slave,
+					pl08x->pd->num_slave_channels, true);
+		if (ret < 0) {
+			dev_warn(&pl08x->adev->dev,
+				 "%s failed to enumerate slave channels - %d\n",
+				 __func__, ret);
+			goto out_no_slave;
+		}
 	}
 
 	ret = dma_async_device_register(&pl08x->memcpy);
@@ -2427,12 +2952,14 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 		goto out_no_memcpy_reg;
 	}
 
-	ret = dma_async_device_register(&pl08x->slave);
-	if (ret) {
-		dev_warn(&pl08x->adev->dev,
+	if (pl08x->has_slave) {
+		ret = dma_async_device_register(&pl08x->slave);
+		if (ret) {
+			dev_warn(&pl08x->adev->dev,
 			"%s failed to register slave as an async device - %d\n",
 			__func__, ret);
-		goto out_no_slave_reg;
+			goto out_no_slave_reg;
+		}
 	}
 
 	amba_set_drvdata(adev, pl08x);
@@ -2446,7 +2973,8 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 out_no_slave_reg:
 	dma_async_device_unregister(&pl08x->memcpy);
 out_no_memcpy_reg:
-	pl08x_free_virtual_channels(&pl08x->slave);
+	if (pl08x->has_slave)
+		pl08x_free_virtual_channels(&pl08x->slave);
 out_no_slave:
 	pl08x_free_virtual_channels(&pl08x->memcpy);
 out_no_memcpy:
@@ -2454,11 +2982,11 @@ static int pl08x_probe(struct amba_device *adev, const struct amba_id *id)
 out_no_phychans:
 	free_irq(adev->irq[0], pl08x);
 out_no_irq:
-	iounmap(pl08x->base);
-out_no_ioremap:
 	dma_pool_destroy(pl08x->pool);
 out_no_lli_pool:
 out_no_platdata:
+	iounmap(pl08x->base);
+out_no_ioremap:
 	kfree(pl08x);
 out_no_pl08x:
 	amba_release_regions(adev);
@@ -2499,6 +3027,12 @@ static struct vendor_data vendor_pl081 = {
 	.max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
 };
 
+static struct vendor_data vendor_ftdmac020 = {
+	.config_offset = PL080_CH_CONFIG,
+	.ftdmac020 = true,
+	.max_transfer_size = PL080_CONTROL_TRANSFER_SIZE_MASK,
+};
+
 static struct amba_id pl08x_ids[] = {
 	/* Samsung PL080S variant */
 	{
@@ -2524,6 +3058,12 @@ static struct amba_id pl08x_ids[] = {
 		.mask	= 0x00ffffff,
 		.data	= &vendor_nomadik,
 	},
+	/* Faraday Technology FTDMAC020 */
+	{
+		.id	= 0x0003b080,
+		.mask	= 0x000fffff,
+		.data	= &vendor_ftdmac020,
+	},
 	{ 0, 0 },
 };
 

include/linux/amba/pl080.h

@@ -44,7 +44,14 @@
 
 #define PL080_SYNC				(0x34)
 
-/* Per channel configuration registers */
+/* The Faraday Technology FTDMAC020 variant registers */
+#define FTDMAC020_CH_BUSY			(0x20)
+/* Identical to PL080_CONFIG */
+#define FTDMAC020_CSR				(0x24)
+/* Identical to PL080_SYNC */
+#define FTDMAC020_SYNC				(0x2C)
+#define FTDMAC020_REVISION			(0x30)
+#define FTDMAC020_FEATURE			(0x34)
 
 /* Per channel configuration registers */
 #define PL080_Cx_BASE(x)			((0x100 + (x * 0x20)))
@@ -55,13 +62,20 @@
 #define PL080_CH_CONFIG				(0x10)
 #define PL080S_CH_CONTROL2			(0x10)
 #define PL080S_CH_CONFIG			(0x14)
-
-#define PL080_LLI_ADDR_MASK			(0x3fffffff << 2)
+/* The Faraday FTDMAC020 derivative shuffles the registers around */
+#define FTDMAC020_CH_CSR			(0x00)
+#define FTDMAC020_CH_CFG			(0x04)
+#define FTDMAC020_CH_SRC_ADDR			(0x08)
+#define FTDMAC020_CH_DST_ADDR			(0x0C)
+#define FTDMAC020_CH_LLP			(0x10)
+#define FTDMAC020_CH_SIZE			(0x14)
+
+#define PL080_LLI_ADDR_MASK			GENMASK(31, 2)
 #define PL080_LLI_ADDR_SHIFT			(2)
 #define PL080_LLI_LM_AHB2			BIT(0)
 
 #define PL080_CONTROL_TC_IRQ_EN			BIT(31)
-#define PL080_CONTROL_PROT_MASK			(0x7 << 28)
+#define PL080_CONTROL_PROT_MASK			GENMASK(30, 28)
 #define PL080_CONTROL_PROT_SHIFT		(28)
 #define PL080_CONTROL_PROT_CACHE		BIT(30)
 #define PL080_CONTROL_PROT_BUFF			BIT(29)
@@ -70,16 +84,16 @@
 #define PL080_CONTROL_SRC_INCR			BIT(26)
 #define PL080_CONTROL_DST_AHB2			BIT(25)
 #define PL080_CONTROL_SRC_AHB2			BIT(24)
-#define PL080_CONTROL_DWIDTH_MASK		(0x7 << 21)
+#define PL080_CONTROL_DWIDTH_MASK		GENMASK(23, 21)
 #define PL080_CONTROL_DWIDTH_SHIFT		(21)
-#define PL080_CONTROL_SWIDTH_MASK		(0x7 << 18)
+#define PL080_CONTROL_SWIDTH_MASK		GENMASK(20, 18)
 #define PL080_CONTROL_SWIDTH_SHIFT		(18)
-#define PL080_CONTROL_DB_SIZE_MASK		(0x7 << 15)
+#define PL080_CONTROL_DB_SIZE_MASK		GENMASK(17, 15)
 #define PL080_CONTROL_DB_SIZE_SHIFT		(15)
-#define PL080_CONTROL_SB_SIZE_MASK		(0x7 << 12)
+#define PL080_CONTROL_SB_SIZE_MASK		GENMASK(14, 12)
 #define PL080_CONTROL_SB_SIZE_SHIFT		(12)
-#define PL080_CONTROL_TRANSFER_SIZE_MASK	(0xfff << 0)
-#define PL080S_CONTROL_TRANSFER_SIZE_MASK	(0x1ffffff << 0)
+#define PL080_CONTROL_TRANSFER_SIZE_MASK	GENMASK(11, 0)
+#define PL080S_CONTROL_TRANSFER_SIZE_MASK	GENMASK(24, 0)
 #define PL080_CONTROL_TRANSFER_SIZE_SHIFT	(0)
 
 #define PL080_BSIZE_1				(0x0)
@@ -102,11 +116,11 @@
 #define PL080_CONFIG_LOCK			BIT(16)
 #define PL080_CONFIG_TC_IRQ_MASK		BIT(15)
 #define PL080_CONFIG_ERR_IRQ_MASK		BIT(14)
-#define PL080_CONFIG_FLOW_CONTROL_MASK		(0x7 << 11)
+#define PL080_CONFIG_FLOW_CONTROL_MASK		GENMASK(13, 11)
 #define PL080_CONFIG_FLOW_CONTROL_SHIFT		(11)
-#define PL080_CONFIG_DST_SEL_MASK		(0xf << 6)
+#define PL080_CONFIG_DST_SEL_MASK		GENMASK(9, 6)
 #define PL080_CONFIG_DST_SEL_SHIFT		(6)
-#define PL080_CONFIG_SRC_SEL_MASK		(0xf << 1)
+#define PL080_CONFIG_SRC_SEL_MASK		GENMASK(4, 1)
 #define PL080_CONFIG_SRC_SEL_SHIFT		(1)
 #define PL080_CONFIG_ENABLE			BIT(0)
 
@@ -119,6 +133,73 @@
 #define PL080_FLOW_PER2MEM_PER			(0x6)
 #define PL080_FLOW_SRC2DST_SRC			(0x7)
 
+#define FTDMAC020_CH_CSR_TC_MSK			BIT(31)
+/* Later versions have a threshold in bits 24..26,  */
+#define FTDMAC020_CH_CSR_FIFOTH_MSK		GENMASK(26, 24)
+#define FTDMAC020_CH_CSR_FIFOTH_SHIFT		(24)
+#define FTDMAC020_CH_CSR_CHPR1_MSK		GENMASK(23, 22)
+#define FTDMAC020_CH_CSR_PROT3			BIT(21)
+#define FTDMAC020_CH_CSR_PROT2			BIT(20)
+#define FTDMAC020_CH_CSR_PROT1			BIT(19)
+#define FTDMAC020_CH_CSR_SRC_SIZE_MSK		GENMASK(18, 16)
+#define FTDMAC020_CH_CSR_SRC_SIZE_SHIFT		(16)
+#define FTDMAC020_CH_CSR_ABT			BIT(15)
+#define FTDMAC020_CH_CSR_SRC_WIDTH_MSK		GENMASK(13, 11)
+#define FTDMAC020_CH_CSR_SRC_WIDTH_SHIFT	(11)
+#define FTDMAC020_CH_CSR_DST_WIDTH_MSK		GENMASK(10, 8)
+#define FTDMAC020_CH_CSR_DST_WIDTH_SHIFT	(8)
+#define FTDMAC020_CH_CSR_MODE			BIT(7)
+/* 00 = increase, 01 = decrease, 10 = fix */
+#define FTDMAC020_CH_CSR_SRCAD_CTL_MSK		GENMASK(6, 5)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_SHIFT	(5)
+#define FTDMAC020_CH_CSR_DSTAD_CTL_MSK		GENMASK(4, 3)
+#define FTDMAC020_CH_CSR_DSTAD_CTL_SHIFT	(3)
+#define FTDMAC020_CH_CSR_SRC_SEL		BIT(2)
+#define FTDMAC020_CH_CSR_DST_SEL		BIT(1)
+#define FTDMAC020_CH_CSR_EN			BIT(0)
+
+/* FIFO threshold setting */
+#define FTDMAC020_CH_CSR_FIFOTH_1		(0x0)
+#define FTDMAC020_CH_CSR_FIFOTH_2		(0x1)
+#define FTDMAC020_CH_CSR_FIFOTH_4		(0x2)
+#define FTDMAC020_CH_CSR_FIFOTH_8		(0x3)
+#define FTDMAC020_CH_CSR_FIFOTH_16		(0x4)
+/* The FTDMAC020 supports 64bit wide transfers */
+#define FTDMAC020_WIDTH_64BIT			(0x3)
+/* Address can be increased, decreased or fixed */
+#define FTDMAC020_CH_CSR_SRCAD_CTL_INC		(0x0)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_DEC		(0x1)
+#define FTDMAC020_CH_CSR_SRCAD_CTL_FIXED	(0x2)
+
+#define FTDMAC020_CH_CFG_LLP_CNT_MASK		GENMASK(19, 16)
+#define FTDMAC020_CH_CFG_LLP_CNT_SHIFT		(16)
+#define FTDMAC020_CH_CFG_BUSY			BIT(8)
+#define FTDMAC020_CH_CFG_INT_ABT_MASK		BIT(2)
+#define FTDMAC020_CH_CFG_INT_ERR_MASK		BIT(1)
+#define FTDMAC020_CH_CFG_INT_TC_MASK		BIT(0)
+
+/* Inside the LLIs, the applicable CSR fields are mapped differently */
+#define FTDMAC020_LLI_TC_MSK			BIT(28)
+#define FTDMAC020_LLI_SRC_WIDTH_MSK		GENMASK(27, 25)
+#define FTDMAC020_LLI_SRC_WIDTH_SHIFT		(25)
+#define FTDMAC020_LLI_DST_WIDTH_MSK		GENMASK(24, 22)
+#define FTDMAC020_LLI_DST_WIDTH_SHIFT		(22)
+#define FTDMAC020_LLI_SRCAD_CTL_MSK		GENMASK(21, 20)
+#define FTDMAC020_LLI_SRCAD_CTL_SHIFT		(20)
+#define FTDMAC020_LLI_DSTAD_CTL_MSK		GENMASK(19, 18)
+#define FTDMAC020_LLI_DSTAD_CTL_SHIFT		(18)
+#define FTDMAC020_LLI_SRC_SEL			BIT(17)
+#define FTDMAC020_LLI_DST_SEL			BIT(16)
+#define FTDMAC020_LLI_TRANSFER_SIZE_MASK	GENMASK(11, 0)
+#define FTDMAC020_LLI_TRANSFER_SIZE_SHIFT	(0)
+
+#define FTDMAC020_CFG_LLP_CNT_MASK		GENMASK(19, 16)
+#define FTDMAC020_CFG_LLP_CNT_SHIFT		(16)
+#define FTDMAC020_CFG_BUSY			BIT(8)
+#define FTDMAC020_CFG_INT_ABT_MSK		BIT(2)
+#define FTDMAC020_CFG_INT_ERR_MSK		BIT(1)
+#define FTDMAC020_CFG_INT_TC_MSK		BIT(0)
+
 /* DMA linked list chain structure */
 
 struct pl080_lli {

include/linux/amba/pl08x.h

@@ -47,8 +47,6 @@ enum {
  * devices with static assignments
  * @muxval: a number usually used to poke into some mux regiser to
  * mux in the signal to this channel
- * @cctl_memcpy: options for the channel control register for memcpy
- *  *** not used for slave channels ***
  * @addr: source/target address in physical memory for this DMA channel,
  * can be the address of a FIFO register for burst requests for example.
  * This can be left undefined if the PrimeCell API is used for configuring
@@ -63,12 +61,28 @@ struct pl08x_channel_data {
 	int min_signal;
 	int max_signal;
 	u32 muxval;
-	u32 cctl_memcpy;
 	dma_addr_t addr;
 	bool single;
 	u8 periph_buses;
 };
 
+enum pl08x_burst_size {
+	PL08X_BURST_SZ_1,
+	PL08X_BURST_SZ_4,
+	PL08X_BURST_SZ_8,
+	PL08X_BURST_SZ_16,
+	PL08X_BURST_SZ_32,
+	PL08X_BURST_SZ_64,
+	PL08X_BURST_SZ_128,
+	PL08X_BURST_SZ_256,
+};
+
+enum pl08x_bus_width {
+	PL08X_BUS_WIDTH_8_BITS,
+	PL08X_BUS_WIDTH_16_BITS,
+	PL08X_BUS_WIDTH_32_BITS,
+};
+
 /**
  * struct pl08x_platform_data - the platform configuration for the PL08x
  * PrimeCells.
@@ -76,6 +90,11 @@ struct pl08x_channel_data {
  * platform, all inclusive, including multiplexed channels. The available
  * physical channels will be multiplexed around these signals as they are
  * requested, just enumerate all possible channels.
+ * @num_slave_channels: number of elements in the slave channel array
+ * @memcpy_burst_size: the appropriate burst size for memcpy operations
+ * @memcpy_bus_width: memory bus width
+ * @memcpy_prot_buff: whether memcpy DMA is bufferable
+ * @memcpy_prot_cache: whether memcpy DMA is cacheable
  * @get_xfer_signal: request a physical signal to be used for a DMA transfer
  * immediately: if there is some multiplexing or similar blocking the use
  * of the channel the transfer can be denied by returning less than zero,
@@ -90,7 +109,10 @@ struct pl08x_channel_data {
 struct pl08x_platform_data {
 	struct pl08x_channel_data *slave_channels;
 	unsigned int num_slave_channels;
-	struct pl08x_channel_data memcpy_channel;
+	enum pl08x_burst_size memcpy_burst_size;
+	enum pl08x_bus_width memcpy_bus_width;
+	bool memcpy_prot_buff;
+	bool memcpy_prot_cache;
 	int (*get_xfer_signal)(const struct pl08x_channel_data *);
 	void (*put_xfer_signal)(const struct pl08x_channel_data *, int);
 	u8 lli_buses;