Merge tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This is mostly a drivers update including a couple of new drivers but
  we do have some fixes and improvements to the core as well.

   - Make sure we don't log spuriously about uncontrollable regulators.

   - Don't use delays when we should use sleeps for regulators with
     larger ramp times.

   - Support for MediaTek MT6358 and MT6366, Richtek RT5759 and Silicon
     Mitus SM5703"

* tag 'regulator-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (36 commits)
  regulator: scmi: Fix refcount leak in scmi_regulator_probe
  regulator: pfuze100: Fix refcount leak in pfuze_parse_regulators_dt
  regulator: qcom_smd: Fix up PM8950 regulator configuration
  regulator: core: Fix enable_count imbalance with EXCLUSIVE_GET
  regulator: core: Add error flags to sysfs attributes
  regulator: dt-bindings: qcom,rpmh: document vdd-l7-bob-supply on PMR735A
  regulator: dt-bindings: qcom,rpmh: document supplies per variant
  regulator: dt-bindings: qcom,rpmh: update maintainers
  regulator: mt6315: Enforce regulator-compatible, not name
  regulator: pca9450: Enable DVS control via PMIC_STBY_REQ
  regulator: pca9450: Make warm reset on WDOG_B assertion
  regulator: Add property for WDOG_B warm reset
  regulator: pca9450: Make I2C Level Translator configurable
  regulator: Add property for I2C level shifter
  regulator: sm5703: Correct reference to the common regulator schema
  regulator: sm5703-regulator: Add regulators support for SM5703 MFD
  dt-bindings: regulator: Add bindings for Silicon Mitus SM5703 regulators
  regulator: richtek,rt4801: parse GPIOs per regulator
  regulator: dt-bindings: richtek,rt4801: use existing ena_gpiod feature
  regulator: core: Sleep (not delay) in set_voltage()
  ...

Documentation/ABI/testing/sysfs-class-regulator

@@ -370,3 +370,84 @@ Description:
 
 		'unknown' means software cannot determine the state, or
 		the reported state is invalid.
+
+What:		/sys/class/regulator/.../under_voltage
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		under_voltage.  This indicates if the device reports an
+		under-voltage fault (1) or not (0).
+
+What:		/sys/class/regulator/.../over_current
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		over_current.  This indicates if the device reports an
+		over-current fault (1) or not (0).
+
+What:		/sys/class/regulator/.../regulation_out
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		regulation_out.  This indicates if the device reports an
+		out-of-regulation fault (1) or not (0).
+
+What:		/sys/class/regulator/.../fail
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		fail.  This indicates if the device reports an output failure
+		(1) or not (0).
+
+What:		/sys/class/regulator/.../over_temp
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		over_temp.  This indicates if the device reports an
+		over-temperature fault (1) or not (0).
+
+What:		/sys/class/regulator/.../under_voltage_warn
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		under_voltage_warn.  This indicates if the device reports an
+		under-voltage warning (1) or not (0).
+
+What:		/sys/class/regulator/.../over_current_warn
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		over_current_warn.  This indicates if the device reports an
+		over-current warning (1) or not (0).
+
+What:		/sys/class/regulator/.../over_voltage_warn
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		over_voltage_warn.  This indicates if the device reports an
+		over-voltage warning (1) or not (0).
+
+What:		/sys/class/regulator/.../over_temp_warn
+Date:		April 2022
+KernelVersion:	5.18
+Contact:	Zev Weiss <zev@bewilderbeest.net>
+Description:
+		Some regulator directories will contain a field called
+		over_temp_warn.  This indicates if the device reports an
+		over-temperature warning (1) or not (0).

Documentation/devicetree/bindings/regulator/mt6315-regulator.yaml

@@ -31,7 +31,7 @@ properties:
         $ref: "regulator.yaml#"
 
         properties:
-          regulator-name:
+          regulator-compatible:
             pattern: "^vbuck[1-4]$"
 
     additionalProperties: false

Documentation/devicetree/bindings/regulator/mt6358-regulator.txt

@@ -8,14 +8,14 @@ Documentation/devicetree/bindings/regulator/regulator.txt.
 
 The valid names for regulators are::
 BUCK:
-  buck_vdram1, buck_vcore, buck_vpa, buck_vproc11, buck_vproc12, buck_vgpu,
-  buck_vs2, buck_vmodem, buck_vs1
+  buck_vdram1, buck_vcore, buck_vcore_sshub, buck_vpa, buck_vproc11,
+  buck_vproc12, buck_vgpu, buck_vs2, buck_vmodem, buck_vs1
 LDO:
   ldo_vdram2, ldo_vsim1, ldo_vibr, ldo_vrf12, ldo_vio18, ldo_vusb, ldo_vcamio,
   ldo_vcamd, ldo_vcn18, ldo_vfe28, ldo_vsram_proc11, ldo_vcn28, ldo_vsram_others,
-  ldo_vsram_gpu, ldo_vxo22, ldo_vefuse, ldo_vaux18, ldo_vmch, ldo_vbif28,
-  ldo_vsram_proc12, ldo_vcama1, ldo_vemc, ldo_vio28, ldo_va12, ldo_vrf18,
-  ldo_vcn33_bt, ldo_vcn33_wifi, ldo_vcama2, ldo_vmc, ldo_vldo28, ldo_vaud28,
+  ldo_vsram_others_sshub, ldo_vsram_gpu, ldo_vxo22, ldo_vefuse, ldo_vaux18,
+  ldo_vmch, ldo_vbif28, ldo_vsram_proc12, ldo_vcama1, ldo_vemc, ldo_vio28, ldo_va12,
+  ldo_vrf18, ldo_vcn33_bt, ldo_vcn33_wifi, ldo_vcama2, ldo_vmc, ldo_vldo28, ldo_vaud28,
   ldo_vsim2
 
 Example:
@@ -354,5 +354,17 @@ Example:
 				regulator-max-microvolt = <3100000>;
 				regulator-enable-ramp-delay = <540>;
 			};
+
+			mt6358_vcore_sshub_reg: buck_vcore_sshub {
+				regulator-name = "vcore_sshub";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+			};
+
+			mt6358_vsram_others_sshub_reg: ldo_vsram_others_sshub {
+				regulator-name = "vsram_others_sshub";
+				regulator-min-microvolt = <500000>;
+				regulator-max-microvolt = <1293750>;
+			};
 		};
 	};

Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml

@@ -92,6 +92,17 @@ properties:
       LDO5CTRL_L or LDO5CTRL_H register. Use this if the SD_VSEL signal is
       connected to a host GPIO.
 
+  nxp,i2c-lt-enable:
+    type: boolean
+    description:
+      Indicates that the I2C Level Translator is used.
+
+  nxp,wdog_b-warm-reset:
+    type: boolean
+    description:
+      When WDOG_B signal is asserted a warm reset will be done instead of cold
+      reset.
+
 required:
   - compatible
   - reg

Documentation/devicetree/bindings/regulator/qcom,rpmh-regulator.yaml

@@ -7,7 +7,8 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: Qualcomm Technologies, Inc. RPMh Regulators
 
 maintainers:
-  - David Collins <collinsd@codeaurora.org>
+  - Bjorn Andersson <bjorn.andersson@linaro.org>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
 
 description: |
     rpmh-regulator devices support PMIC regulator management via the Voltage
@@ -78,7 +79,7 @@ properties:
         RPMh resource name suffix used for the regulators found
         on this PMIC.
     $ref: /schemas/types.yaml#/definitions/string
-    enum: [a, b, c, d, e, f]
+    enum: [a, b, c, d, e, f, h, k]
 
   qcom,always-wait-for-ack:
     description: |
@@ -94,35 +95,264 @@ properties:
   vdd-rgb-supply:
     description: Input supply phandle of rgb.
 
-  vin-lvs-1-2-supply:
-    description: Input supply phandle of one or more regulators.
-
-  vdd-bob-supply:
-    description: BOB regulator parent supply phandle.
-
   bob:
     type: object
     $ref: "regulator.yaml#"
     description: BOB regulator node.
 
 patternProperties:
-  "^vdd-s([0-9]+)-supply$":
-    description: Input supply phandle(s) of one or more regulators.
-
-  "^vdd-(l[0-9]+[-]){1,5}supply$":
-    description: Input supply phandle(s) of one or more regulators.
-
   "^(smps|ldo|lvs)[0-9]+$":
     type: object
     $ref: "regulator.yaml#"
     description: smps/ldo regulator nodes(s).
 
-additionalProperties: false
-
 required:
   - compatible
   - qcom,pmic-id
 
+allOf:
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm6150-rpmh-regulators
+    then:
+      properties:
+        vdd-l2-l3-supply: true
+        vdd-l4-l7-l8-supply: true
+        vdd-l5-l16-l17-l18-l19-supply: true
+        vdd-l10-l14-l15-supply: true
+        vdd-l11-l12-l13-supply: true
+      patternProperties:
+        "^vdd-l[169]-supply$": true
+        "^vdd-s[1-5]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm6150l-rpmh-regulators
+    then:
+      properties:
+        vdd-bob-supply:
+          description: BOB regulator parent supply phandle.
+        vdd-l1-l8-supply: true
+        vdd-l2-l3-supply: true
+        vdd-l4-l5-l6-supply: true
+        vdd-l7-l11-supply: true
+        vdd-l9-l10-supply: true
+      patternProperties:
+        "^vdd-s[1-8]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm7325-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l4-l12-l15-supply: true
+        vdd-l2-l7-supply: true
+        vdd-l6-l9-l10-supply: true
+        vdd-l11-l17-l18-l19-supply: true
+        vdd-l13-supply: true
+        vdd-l14-l16-supply: true
+      patternProperties:
+        "^vdd-l[358]-supply$": true
+        "^vdd-s[1-8]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8005-rpmh-regulators
+    then:
+      patternProperties:
+        "^vdd-s[1-4]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8009-rpmh-regulators
+            - qcom,pm8009-1-rpmh-regulators
+    then:
+      properties:
+        vdd-l5-l6-supply: true
+      patternProperties:
+        "^vdd-l[1-47]-supply$": true
+        "^vdd-s[1-2]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8150-rpmh-regulators
+            - qcom,pmm8155au-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l8-l11-supply: true
+        vdd-l2-l10-supply: true
+        vdd-l3-l4-l5-l18-supply: true
+        vdd-l6-l9-supply: true
+        vdd-l7-l12-l14-l15-supply: true
+        vdd-l13-l16-l17-supply: true
+      patternProperties:
+        "^vdd-s([1-9]|10)-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8150l-rpmh-regulators
+    then:
+      properties:
+        vdd-bob-supply:
+          description: BOB regulator parent supply phandle.
+        vdd-l1-l8-supply: true
+        vdd-l2-l3-supply: true
+        vdd-l4-l5-l6-supply: true
+        vdd-l7-l11-supply: true
+        vdd-l9-l10-supply: true
+      patternProperties:
+        "^vdd-s[1-8]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8350-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l4-supply: true
+        vdd-l2-l7-supply: true
+        vdd-l3-l5-supply: true
+        vdd-l6-l9-l10-supply: true
+        vdd-l8-supply: true
+      patternProperties:
+        "^vdd-s([1-9]|1[0-2])-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8350c-rpmh-regulators
+    then:
+      properties:
+        vdd-bob-supply:
+          description: BOB regulator parent supply phandle.
+        vdd-l1-l12-supply: true
+        vdd-l2-l8-supply: true
+        vdd-l3-l4-l5-l7-l13-supply: true
+        vdd-l6-l9-l11-supply: true
+        vdd-l10-supply: true
+      patternProperties:
+        "^vdd-s([1-9]|10)-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8450-rpmh-regulators
+    then:
+      patternProperties:
+        "^vdd-l[1-4]-supply$": true
+        "^vdd-s[1-6]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pm8998-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l27-supply: true
+        vdd-l2-l8-l17-supply: true
+        vdd-l3-l11-supply: true
+        vdd-l4-l5-supply: true
+        vdd-l6-supply: true
+        vdd-l7-l12-l14-l15-supply: true
+        vdd-l9-supply: true
+        vdd-l10-l23-l25-supply: true
+        vdd-l13-l19-l21-supply: true
+        vdd-l16-l28-supply: true
+        vdd-l18-l22-supply: true
+        vdd-l20-l24-supply: true
+        vdd-l26-supply: true
+        vin-lvs-1-2-supply: true
+      patternProperties:
+        "^vdd-s([1-9]|1[0-3])-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmg1110-rpmh-regulators
+    then:
+      properties:
+        vdd-s1-supply: true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmi8998-rpmh-regulators
+    then:
+      properties:
+        vdd-bob-supply:
+          description: BOB regulator parent supply phandle.
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmr735a-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l2-supply: true
+        vdd-l3-supply: true
+        vdd-l4-supply: true
+        vdd-l5-l6-supply: true
+        vdd-l7-bob-supply: true
+      patternProperties:
+        "^vdd-s[1-3]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmx55-rpmh-regulators
+    then:
+      properties:
+        vdd-l1-l2-supply: true
+        vdd-l3-l9-supply: true
+        vdd-l4-l12-supply: true
+        vdd-l5-l6-supply: true
+        vdd-l7-l8-supply: true
+        vdd-l10-l11-l13-supply: true
+      patternProperties:
+        "^vdd-l1[4-6]-supply$": true
+        "^vdd-s[1-7]-supply$": true
+
+  - if:
+      properties:
+        compatible:
+          enum:
+            - qcom,pmx65-rpmh-regulators
+    then:
+      properties:
+        vdd-l2-l18-supply: true
+        vdd-l5-l6-l16-supply: true
+        vdd-l8-l9-supply: true
+        vdd-l11-l13-supply: true
+      patternProperties:
+        "^vdd-l[1347]-supply$": true
+        "^vdd-l1[0245789]-supply$": true
+        "^vdd-l2[01]-supply$": true
+        "^vdd-s[1-8]-supply$": true
+
+unevaluatedProperties: false
+
 examples:
   - |
     #include <dt-bindings/regulator/qcom,rpmh-regulator.h>

Documentation/devicetree/bindings/regulator/richtek,rt4801-regulator.yaml

@@ -17,9 +17,6 @@ description: |
   Datasheet is available at
   https://www.richtek.com/assets/product_file/RT4801H/DS4801H-00.pdf
 
-#The valid names for RT4801 regulator nodes are:
-#DSVP, DSVN
-
 properties:
   compatible:
     enum:
@@ -33,10 +30,13 @@ properties:
       The first one is ENP to enable DSVP, and second one is ENM to enable DSVN.
       Number of GPIO in the array list could be 1 or 2.
       If only one gpio is specified, only one gpio used to control ENP/ENM.
-      Else both are spefied, DSVP/DSVN could be controlled individually.
-      Othersie, this property not specified. treat both as always-on regulator.
+      Else if both are specified, DSVP/DSVN could be controlled individually.
+      If this property not specified, treat both as always-on regulators.
+
+      Property is deprecated. Use enable-gpios in each regulator.
     minItems: 1
     maxItems: 2
+    deprecated: true
 
 patternProperties:
   "^DSV(P|N)$":
@@ -45,6 +45,14 @@ patternProperties:
     description:
       Properties for single display bias regulator.
 
+    properties:
+      enable-gpios:
+        description:
+          GPIO to use to enable DSVP/DSVN regulator. One GPIO can be configured
+          for controlling both regulators.  If this property not specified for
+          any regulator, treat both as always-on regulators.
+        maxItems: 1
+
 required:
   - compatible
   - reg
@@ -60,19 +68,20 @@ examples:
         rt4801@73 {
             compatible = "richtek,rt4801";
             reg = <0x73>;
-            enable-gpios = <&gpio26 2 0>, <&gpio26 3 0>;
 
             dsvp: DSVP {
                 regulator-name = "rt4801,dsvp";
                 regulator-min-microvolt = <4000000>;
                 regulator-max-microvolt = <6000000>;
                 regulator-boot-on;
+                enable-gpios = <&gpio26 2 0>;
             };
             dsvn: DSVN {
                 regulator-name = "rt4801,dsvn";
                 regulator-min-microvolt = <4000000>;
                 regulator-max-microvolt = <6000000>;
                 regulator-boot-on;
+                enable-gpios = <&gpio26 3 0>;
             };
 
         };

Documentation/devicetree/bindings/regulator/richtek,rt5759-regulator.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/richtek,rt5759-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Richtek RT5759 High Performance DCDC Converter
+
+maintainers:
+  - ChiYuan Huang <cy_huang@richtek.com>
+
+description: |
+  The RT5759 is a high-performance, synchronous step-down DC-DC converter that
+  can deliver up to 9A output current from 3V to 6.5V input supply, The output
+  voltage can be programmable with I2C controlled 7-Bit VID.
+
+  Datasheet is available at
+  https://www.richtek.com/assets/product_file/RT5759/DS5759-00.pdf
+
+properties:
+  compatible:
+    enum:
+      - richtek,rt5759
+      - richtek,rt5759a
+
+  reg:
+    maxItems: 1
+
+  regulator-allowed-modes:
+    description: |
+      buck allowed operating mode
+        0: auto mode (PSKIP: pulse skipping)
+        1: force pwm mode
+    items:
+      enum: [0, 1]
+
+  richtek,watchdog-enable:
+    description: enable the external watchdog reset pin listening
+    type: boolean
+
+allOf:
+  - $ref: regulator.yaml#
+
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: richtek,rt5759
+    then:
+      properties:
+        richtek,watchdog-enable: false
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  # example 1 for RT5759
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      regulator@62 {
+        compatible = "richtek,rt5759";
+        reg = <0x62>;
+        regulator-name = "rt5759-buck";
+        regulator-min-microvolt = <600000>;
+        regulator-max-microvolt = <1500000>;
+        regulator-boot-on;
+      };
+    };
+  # example 2 for RT5759A
+  - |
+    i2c {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      regulator@62 {
+        compatible = "richtek,rt5759a";
+        reg = <0x62>;
+        regulator-name = "rt5759a-buck";
+        regulator-min-microvolt = <600000>;
+        regulator-max-microvolt = <1725000>;
+        regulator-boot-on;
+        richtek,watchdog-enable;
+      };
+    };

Documentation/devicetree/bindings/regulator/siliconmitus,sm5703-regulator.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/siliconmitus,sm5703-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Silicon Mitus SM5703 multi function device regulators
+
+maintainers:
+  - Markuss Broks <markuss.broks@gmail.com>
+
+description: |
+  SM5703 regulators node should be a sub node of the SM5703 MFD node. See SM5703 MFD
+  bindings at Documentation/devicetree/bindings/mfd/siliconmitus,sm5703.yaml
+  Regulator nodes should be named as USBLDO_<number>, BUCK, VBUS, LDO_<number>.
+  The definition for each of these nodes is defined using the standard
+  binding for regulators at Documentation/devicetree/bindings/regulator/regulator.txt.
+
+properties:
+  buck:
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+    description:
+      Properties for the BUCK regulator.
+
+  vbus:
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+    description:
+      Properties for the VBUS regulator.
+
+patternProperties:
+  "^ldo[1-3]$":
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+    description:
+      Properties for single LDO regulator.
+
+  "^usbldo[1-2]$":
+    type: object
+    $ref: regulator.yaml#
+    unevaluatedProperties: false
+    description:
+      Properties for a single USBLDO regulator.
+
+additionalProperties: false

Documentation/devicetree/bindings/regulator/socionext,uniphier-regulator.yaml

@@ -14,9 +14,6 @@ description: |
 maintainers:
   - Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
 
-allOf:
-  - $ref: "regulator.yaml#"
-
 # USB3 Controller
 
 properties:
@@ -36,27 +33,51 @@ properties:
     minItems: 1
     maxItems: 2
 
-  clock-names:
-    oneOf:
-      - items:          # for Pro4, Pro5
-          - const: gio
-          - const: link
-      - items:          # for others
-          - const: link
+  clock-names: true
 
   resets:
     minItems: 1
     maxItems: 2
 
-  reset-names:
-    oneOf:
-      - items:          # for Pro4, Pro5
-          - const: gio
-          - const: link
-      - items:
-          - const: link
+  reset-names: true
 
-additionalProperties: false
+allOf:
+  - $ref: "regulator.yaml#"
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - socionext,uniphier-pro4-usb3-regulator
+              - socionext,uniphier-pro5-usb3-regulator
+    then:
+      properties:
+        clocks:
+          minItems: 2
+          maxItems: 2
+        clock-names:
+          items:
+            - const: gio
+            - const: link
+        resets:
+          minItems: 2
+          maxItems: 2
+        reset-names:
+          items:
+            - const: gio
+            - const: link
+    else:
+      properties:
+        clocks:
+          maxItems: 1
+        clock-names:
+          const: link
+        resets:
+          maxItems: 1
+        reset-names:
+          const: link
+
+unevaluatedProperties: false
 
 required:
   - compatible

drivers/regulator/Kconfig

@@ -1057,6 +1057,16 @@ config REGULATOR_RT5190A
 	  buck converters, 1 LDO, mute AC OFF depop function, with the general
 	  I2C control interface.
 
+config REGULATOR_RT5759
+	tristate "Richtek RT5759 Regulator"
+	depends on I2C
+	select REGMAP_I2C
+	help
+	  This adds support for voltage regulator in Richtek RT5759.
+	  The RT5759 is a high-performance, synchronous step-down DC-DC
+	  converter that can deliver up to 9A output current from 3V to 6.5V
+	  input supply.
+
 config REGULATOR_RT6160
 	tristate "Richtek RT6160 BuckBoost voltage regulator"
 	depends on I2C
@@ -1157,6 +1167,13 @@ config REGULATOR_SLG51000
 	  The SLG51000 is seven compact and customizable low dropout
 	  regulators.
 
+config REGULATOR_SM5703
+	tristate "Silicon Mitus SM5703 regulators"
+	depends on MFD_SM5703
+	help
+	  This driver provides support for voltage regulators of SM5703
+	  multi-function device.
+
 config REGULATOR_STM32_BOOSTER
 	tristate "STMicroelectronics STM32 BOOSTER"
 	depends on ARCH_STM32 || COMPILE_TEST

drivers/regulator/Makefile

@@ -127,6 +127,7 @@ obj-$(CONFIG_REGULATOR_RT4801)	+= rt4801-regulator.o
 obj-$(CONFIG_REGULATOR_RT4831)	+= rt4831-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
 obj-$(CONFIG_REGULATOR_RT5190A) += rt5190a-regulator.o
+obj-$(CONFIG_REGULATOR_RT5759)	+= rt5759-regulator.o
 obj-$(CONFIG_REGULATOR_RT6160)	+= rt6160-regulator.o
 obj-$(CONFIG_REGULATOR_RT6245)	+= rt6245-regulator.o
 obj-$(CONFIG_REGULATOR_RTMV20)	+= rtmv20-regulator.o
@@ -138,6 +139,7 @@ obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
 obj-$(CONFIG_REGULATOR_SC2731) += sc2731-regulator.o
 obj-$(CONFIG_REGULATOR_SKY81452) += sky81452-regulator.o
 obj-$(CONFIG_REGULATOR_SLG51000) += slg51000-regulator.o
+obj-$(CONFIG_REGULATOR_SM5703) += sm5703-regulator.o
 obj-$(CONFIG_REGULATOR_STM32_BOOSTER) += stm32-booster.o
 obj-$(CONFIG_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
 obj-$(CONFIG_REGULATOR_STM32_PWR) += stm32-pwr.o

drivers/regulator/core.c

@@ -83,6 +83,7 @@ struct regulator_supply_alias {
 
 static int _regulator_is_enabled(struct regulator_dev *rdev);
 static int _regulator_disable(struct regulator *regulator);
+static int _regulator_get_error_flags(struct regulator_dev *rdev, unsigned int *flags);
 static int _regulator_get_current_limit(struct regulator_dev *rdev);
 static unsigned int _regulator_get_mode(struct regulator_dev *rdev);
 static int _notifier_call_chain(struct regulator_dev *rdev,
@@ -911,6 +912,30 @@ static ssize_t bypass_show(struct device *dev,
 }
 static DEVICE_ATTR_RO(bypass);
 
+#define REGULATOR_ERROR_ATTR(name, bit)							\
+	static ssize_t name##_show(struct device *dev, struct device_attribute *attr,	\
+				   char *buf)						\
+	{										\
+		int ret;								\
+		unsigned int flags;							\
+		struct regulator_dev *rdev = dev_get_drvdata(dev);			\
+		ret = _regulator_get_error_flags(rdev, &flags);				\
+		if (ret)								\
+			return ret;							\
+		return sysfs_emit(buf, "%d\n", !!(flags & (bit)));			\
+	}										\
+	static DEVICE_ATTR_RO(name)
+
+REGULATOR_ERROR_ATTR(under_voltage, REGULATOR_ERROR_UNDER_VOLTAGE);
+REGULATOR_ERROR_ATTR(over_current, REGULATOR_ERROR_OVER_CURRENT);
+REGULATOR_ERROR_ATTR(regulation_out, REGULATOR_ERROR_REGULATION_OUT);
+REGULATOR_ERROR_ATTR(fail, REGULATOR_ERROR_FAIL);
+REGULATOR_ERROR_ATTR(over_temp, REGULATOR_ERROR_OVER_TEMP);
+REGULATOR_ERROR_ATTR(under_voltage_warn, REGULATOR_ERROR_UNDER_VOLTAGE_WARN);
+REGULATOR_ERROR_ATTR(over_current_warn, REGULATOR_ERROR_OVER_CURRENT_WARN);
+REGULATOR_ERROR_ATTR(over_voltage_warn, REGULATOR_ERROR_OVER_VOLTAGE_WARN);
+REGULATOR_ERROR_ATTR(over_temp_warn, REGULATOR_ERROR_OVER_TEMP_WARN);
+
 /* Calculate the new optimum regulator operating mode based on the new total
  * consumer load. All locks held by caller
  */
@@ -1522,6 +1547,24 @@ static int set_machine_constraints(struct regulator_dev *rdev)
 		}
 	}
 
+	/*
+	 * If there is no mechanism for controlling the regulator then
+	 * flag it as always_on so we don't end up duplicating checks
+	 * for this so much.  Note that we could control the state of
+	 * a supply to control the output on a regulator that has no
+	 * direct control.
+	 */
+	if (!rdev->ena_pin && !ops->enable) {
+		if (rdev->supply_name && !rdev->supply)
+			return -EPROBE_DEFER;
+
+		if (rdev->supply)
+			rdev->constraints->always_on =
+				rdev->supply->rdev->constraints->always_on;
+		else
+			rdev->constraints->always_on = true;
+	}
+
 	/* If the constraints say the regulator should be on at this point
 	 * and we have control then make sure it is enabled.
 	 */
@@ -2133,10 +2176,13 @@ struct regulator *_regulator_get(struct device *dev, const char *id,
 		rdev->exclusive = 1;
 
 		ret = _regulator_is_enabled(rdev);
-		if (ret > 0)
+		if (ret > 0) {
 			rdev->use_count = 1;
-		else
+			regulator->enable_count = 1;
+		} else {
 			rdev->use_count = 0;
+			regulator->enable_count = 0;
+		}
 	}
 
 	link = device_link_add(dev, &rdev->dev, DL_FLAG_STATELESS);
@@ -2511,17 +2557,17 @@ static int regulator_ena_gpio_ctrl(struct regulator_dev *rdev, bool enable)
 }
 
 /**
- * _regulator_enable_delay - a delay helper function
+ * _regulator_delay_helper - a delay helper function
  * @delay: time to delay in microseconds
  *
  * Delay for the requested amount of time as per the guidelines in:
  *
  *     Documentation/timers/timers-howto.rst
  *
- * The assumption here is that regulators will never be enabled in
+ * The assumption here is that these regulator operations will never used in
  * atomic context and therefore sleeping functions can be used.
  */
-static void _regulator_enable_delay(unsigned int delay)
+static void _regulator_delay_helper(unsigned int delay)
 {
 	unsigned int ms = delay / 1000;
 	unsigned int us = delay % 1000;
@@ -2603,7 +2649,7 @@ static int _regulator_do_enable(struct regulator_dev *rdev)
 		s64 remaining = ktime_us_delta(end, ktime_get());
 
 		if (remaining > 0)
-			_regulator_enable_delay(remaining);
+			_regulator_delay_helper(remaining);
 	}
 
 	if (rdev->ena_pin) {
@@ -2630,14 +2676,14 @@ static int _regulator_do_enable(struct regulator_dev *rdev)
 	/* If poll_enabled_time is set, poll upto the delay calculated
 	 * above, delaying poll_enabled_time uS to check if the regulator
 	 * actually got enabled.
-	 * If the regulator isn't enabled after enable_delay has
-	 * expired, return -ETIMEDOUT.
+	 * If the regulator isn't enabled after our delay helper has expired,
+	 * return -ETIMEDOUT.
 	 */
 	if (rdev->desc->poll_enabled_time) {
 		unsigned int time_remaining = delay;
 
 		while (time_remaining > 0) {
-			_regulator_enable_delay(rdev->desc->poll_enabled_time);
+			_regulator_delay_helper(rdev->desc->poll_enabled_time);
 
 			if (rdev->desc->ops->get_status) {
 				ret = _regulator_check_status_enabled(rdev);
@@ -2656,7 +2702,7 @@ static int _regulator_do_enable(struct regulator_dev *rdev)
 			return -ETIMEDOUT;
 		}
 	} else {
-		_regulator_enable_delay(delay);
+		_regulator_delay_helper(delay);
 	}
 
 	trace_regulator_enable_complete(rdev_get_name(rdev));
@@ -3548,12 +3594,7 @@ static int _regulator_do_set_voltage(struct regulator_dev *rdev,
 	}
 
 	/* Insert any necessary delays */
-	if (delay >= 1000) {
-		mdelay(delay / 1000);
-		udelay(delay % 1000);
-	} else if (delay) {
-		udelay(delay);
-	}
+	_regulator_delay_helper(delay);
 
 	if (best_val >= 0) {
 		unsigned long data = best_val;
@@ -4971,6 +5012,15 @@ static struct attribute *regulator_dev_attrs[] = {
 	&dev_attr_max_microvolts.attr,
 	&dev_attr_min_microamps.attr,
 	&dev_attr_max_microamps.attr,
+	&dev_attr_under_voltage.attr,
+	&dev_attr_over_current.attr,
+	&dev_attr_regulation_out.attr,
+	&dev_attr_fail.attr,
+	&dev_attr_over_temp.attr,
+	&dev_attr_under_voltage_warn.attr,
+	&dev_attr_over_current_warn.attr,
+	&dev_attr_over_voltage_warn.attr,
+	&dev_attr_over_temp_warn.attr,
 	&dev_attr_suspend_standby_state.attr,
 	&dev_attr_suspend_mem_state.attr,
 	&dev_attr_suspend_disk_state.attr,
@@ -5026,6 +5076,17 @@ static umode_t regulator_attr_is_visible(struct kobject *kobj,
 	if (attr == &dev_attr_bypass.attr)
 		return ops->get_bypass ? mode : 0;
 
+	if (attr == &dev_attr_under_voltage.attr ||
+	    attr == &dev_attr_over_current.attr ||
+	    attr == &dev_attr_regulation_out.attr ||
+	    attr == &dev_attr_fail.attr ||
+	    attr == &dev_attr_over_temp.attr ||
+	    attr == &dev_attr_under_voltage_warn.attr ||
+	    attr == &dev_attr_over_current_warn.attr ||
+	    attr == &dev_attr_over_voltage_warn.attr ||
+	    attr == &dev_attr_over_temp_warn.attr)
+		return ops->get_error_flags ? mode : 0;
+
 	/* constraints need specific supporting methods */
 	if (attr == &dev_attr_min_microvolts.attr ||
 	    attr == &dev_attr_max_microvolts.attr)

drivers/regulator/da9121-regulator.c

@@ -1030,6 +1030,8 @@ static int da9121_assign_chip_model(struct i2c_client *i2c,
 		chip->variant_id = DA9121_TYPE_DA9142;
 		regmap = &da9121_2ch_regmap_config;
 		break;
+	default:
+		return -EINVAL;
 	}
 
 	/* Set these up for of_regulator_match call which may want .of_map_modes */

drivers/regulator/fixed.c

@@ -236,11 +236,8 @@ static int reg_fixed_voltage_probe(struct platform_device *pdev)
 		drvdata->desc.supply_name = devm_kstrdup(&pdev->dev,
 					    config->input_supply,
 					    GFP_KERNEL);
-		if (!drvdata->desc.supply_name) {
-			dev_err(&pdev->dev,
-				"Failed to allocate input supply\n");
+		if (!drvdata->desc.supply_name)
 			return -ENOMEM;
-		}
 	}
 
 	if (config->microvolts)

drivers/regulator/pca9450-regulator.c

@@ -174,6 +174,14 @@ static int buck_set_dvs(const struct regulator_desc *desc,
 		}
 	}
 
+	if (ret == 0) {
+		struct pca9450_regulator_desc *regulator = container_of(desc,
+					struct pca9450_regulator_desc, desc);
+
+		/* Enable DVS control through PMIC_STBY_REQ for this BUCK */
+		ret = regmap_update_bits(regmap, regulator->desc.enable_reg,
+					 BUCK1_DVS_CTRL, BUCK1_DVS_CTRL);
+	}
 	return ret;
 }
 
@@ -702,6 +710,7 @@ static int pca9450_i2c_probe(struct i2c_client *i2c,
 	struct regulator_config config = { };
 	struct pca9450 *pca9450;
 	unsigned int device_id, i;
+	unsigned int reset_ctrl;
 	int ret;
 
 	if (!i2c->irq) {
@@ -802,14 +811,30 @@ static int pca9450_i2c_probe(struct i2c_client *i2c,
 		return ret;
 	}
 
+	if (of_property_read_bool(i2c->dev.of_node, "nxp,wdog_b-warm-reset"))
+		reset_ctrl = WDOG_B_CFG_WARM;
+	else
+		reset_ctrl = WDOG_B_CFG_COLD_LDO12;
+
 	/* Set reset behavior on assertion of WDOG_B signal */
 	ret = regmap_update_bits(pca9450->regmap, PCA9450_REG_RESET_CTRL,
-				WDOG_B_CFG_MASK, WDOG_B_CFG_COLD_LDO12);
+				 WDOG_B_CFG_MASK, reset_ctrl);
 	if (ret) {
 		dev_err(&i2c->dev, "Failed to set WDOG_B reset behavior\n");
 		return ret;
 	}
 
+	if (of_property_read_bool(i2c->dev.of_node, "nxp,i2c-lt-enable")) {
+		/* Enable I2C Level Translator */
+		ret = regmap_update_bits(pca9450->regmap, PCA9450_REG_CONFIG2,
+					 I2C_LT_MASK, I2C_LT_ON_STANDBY_RUN);
+		if (ret) {
+			dev_err(&i2c->dev,
+				"Failed to enable I2C level translator\n");
+			return ret;
+		}
+	}
+
 	/*
 	 * The driver uses the LDO5CTRL_H register to control the LDO5 regulator.
 	 * This is only valid if the SD_VSEL input of the PMIC is high. Let's

drivers/regulator/pfuze100-regulator.c

@@ -521,6 +521,7 @@ static int pfuze_parse_regulators_dt(struct pfuze_chip *chip)
 	parent = of_get_child_by_name(np, "regulators");
 	if (!parent) {
 		dev_err(dev, "regulators node not found\n");
+		of_node_put(np);
 		return -EINVAL;
 	}
 
@@ -550,6 +551,7 @@ static int pfuze_parse_regulators_dt(struct pfuze_chip *chip)
 	}
 
 	of_node_put(parent);
+	of_node_put(np);
 	if (ret < 0) {
 		dev_err(dev, "Error parsing regulator init data: %d\n",
 			ret);

drivers/regulator/qcom_smd-regulator.c

@@ -944,32 +944,31 @@ static const struct rpm_regulator_data rpm_pm8950_regulators[] = {
 	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8950_hfsmps, "vdd_s2" },
 	{ "s3", QCOM_SMD_RPM_SMPA, 3, &pm8950_hfsmps, "vdd_s3" },
 	{ "s4", QCOM_SMD_RPM_SMPA, 4, &pm8950_hfsmps, "vdd_s4" },
-	{ "s5", QCOM_SMD_RPM_SMPA, 5, &pm8950_ftsmps2p5, "vdd_s5" },
+	/* S5 is managed via SPMI. */
 	{ "s6", QCOM_SMD_RPM_SMPA, 6, &pm8950_hfsmps, "vdd_s6" },
 
 	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pm8950_ult_nldo, "vdd_l1_l19" },
 	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pm8950_ult_nldo, "vdd_l2_l23" },
 	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pm8950_ult_nldo, "vdd_l3" },
-	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pm8950_ult_pldo, "vdd_l4_l5_l6_l7_l16" },
-	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
-	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
-	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8950_pldo_lv, "vdd_l4_l5_l6_l7_l16" },
+	/* L4 seems not to exist. */
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8950_pldo_lv, "vdd_l5_l6_l7_l16" },
 	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
 	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
 	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pm8950_ult_nldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pm8950_ult_pldo, "vdd_l4_l5_l6_l7_l16"},
-	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l18", QCOM_SMD_RPM_LDOA, 18, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18"},
-	{ "l19", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l1_l19"},
-	{ "l20", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l20"},
-	{ "l21", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l21"},
-	{ "l22", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l8_l11_l12_l17_l22"},
-	{ "l23", QCOM_SMD_RPM_LDOA, 18, &pm8950_pldo, "vdd_l2_l23"},
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8950_ult_pldo, "vdd_l9_l10_l13_l14_l15_l18" },
+	{ "l16", QCOM_SMD_RPM_LDOA, 16, &pm8950_ult_pldo, "vdd_l5_l6_l7_l16" },
+	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8950_ult_pldo, "vdd_l8_l11_l12_l17_l22" },
+	/* L18 seems not to exist. */
+	{ "l19", QCOM_SMD_RPM_LDOA, 19, &pm8950_pldo, "vdd_l1_l19" },
+	/* L20 & L21 seem not to exist. */
+	{ "l22", QCOM_SMD_RPM_LDOA, 22, &pm8950_pldo, "vdd_l8_l11_l12_l17_l22" },
+	{ "l23", QCOM_SMD_RPM_LDOA, 23, &pm8950_pldo, "vdd_l2_l23" },
 	{}
 };
 

drivers/regulator/rpi-panel-attiny-regulator.c

@@ -364,7 +364,6 @@ static int attiny_i2c_probe(struct i2c_client *i2c,
 	state->gc.parent = &i2c->dev;
 	state->gc.label = i2c->name;
 	state->gc.owner = THIS_MODULE;
-	state->gc.of_node = i2c->dev.of_node;
 	state->gc.base = -1;
 	state->gc.ngpio = NUM_GPIO;
 

drivers/regulator/rt4801-regulator.c

@@ -29,11 +29,33 @@
 
 struct rt4801_priv {
 	struct device *dev;
-	struct gpio_descs *enable_gpios;
+	struct gpio_desc *enable_gpios[DSV_OUT_MAX];
 	unsigned int enable_flag;
 	unsigned int volt_sel[DSV_OUT_MAX];
 };
 
+static int rt4801_of_parse_cb(struct device_node *np,
+			      const struct regulator_desc *desc,
+			      struct regulator_config *config)
+{
+	struct rt4801_priv *priv = config->driver_data;
+	int id = desc->id;
+
+	if (priv->enable_gpios[id]) {
+		dev_warn(priv->dev, "duplicated enable-gpios property\n");
+		return 0;
+	}
+	priv->enable_gpios[id] = devm_fwnode_gpiod_get_index(priv->dev,
+							     of_fwnode_handle(np),
+							     "enable", 0,
+							     GPIOD_OUT_HIGH,
+							     "rt4801");
+	if (IS_ERR(priv->enable_gpios[id]))
+		priv->enable_gpios[id] = NULL;
+
+	return 0;
+}
+
 static int rt4801_set_voltage_sel(struct regulator_dev *rdev, unsigned int selector)
 {
 	struct rt4801_priv *priv = rdev_get_drvdata(rdev);
@@ -63,15 +85,14 @@ static int rt4801_get_voltage_sel(struct regulator_dev *rdev)
 static int rt4801_enable(struct regulator_dev *rdev)
 {
 	struct rt4801_priv *priv = rdev_get_drvdata(rdev);
-	struct gpio_descs *gpios = priv->enable_gpios;
 	int id = rdev_get_id(rdev), ret;
 
-	if (!gpios || gpios->ndescs <= id) {
+	if (!priv->enable_gpios[id]) {
 		dev_warn(&rdev->dev, "no dedicated gpio can control\n");
 		goto bypass_gpio;
 	}
 
-	gpiod_set_value(gpios->desc[id], 1);
+	gpiod_set_value(priv->enable_gpios[id], 1);
 
 bypass_gpio:
 	ret = regmap_write(rdev->regmap, rdev->desc->vsel_reg, priv->volt_sel[id]);
@@ -85,15 +106,14 @@ static int rt4801_enable(struct regulator_dev *rdev)
 static int rt4801_disable(struct regulator_dev *rdev)
 {
 	struct rt4801_priv *priv = rdev_get_drvdata(rdev);
-	struct gpio_descs *gpios = priv->enable_gpios;
 	int id = rdev_get_id(rdev);
 
-	if (!gpios || gpios->ndescs <= id) {
+	if (!priv->enable_gpios[id]) {
 		dev_warn(&rdev->dev, "no dedicated gpio can control\n");
 		goto bypass_gpio;
 	}
 
-	gpiod_set_value(gpios->desc[id], 0);
+	gpiod_set_value(priv->enable_gpios[id], 0);
 
 bypass_gpio:
 	priv->enable_flag &= ~BIT(id);
@@ -122,6 +142,7 @@ static const struct regulator_desc rt4801_regulator_descs[] = {
 		.name = "DSVP",
 		.ops = &rt4801_regulator_ops,
 		.of_match = of_match_ptr("DSVP"),
+		.of_parse_cb = rt4801_of_parse_cb,
 		.type = REGULATOR_VOLTAGE,
 		.id = DSV_OUT_POS,
 		.min_uV = MIN_UV,
@@ -135,6 +156,7 @@ static const struct regulator_desc rt4801_regulator_descs[] = {
 		.name = "DSVN",
 		.ops = &rt4801_regulator_ops,
 		.of_match = of_match_ptr("DSVN"),
+		.of_parse_cb = rt4801_of_parse_cb,
 		.type = REGULATOR_VOLTAGE,
 		.id = DSV_OUT_NEG,
 		.min_uV = MIN_UV,
@@ -172,10 +194,15 @@ static int rt4801_probe(struct i2c_client *i2c)
 		return PTR_ERR(regmap);
 	}
 
-	priv->enable_gpios = devm_gpiod_get_array_optional(&i2c->dev, "enable", GPIOD_OUT_HIGH);
-	if (IS_ERR(priv->enable_gpios)) {
-		dev_err(&i2c->dev, "Failed to get gpios\n");
-		return PTR_ERR(priv->enable_gpios);
+	for (i = 0; i < DSV_OUT_MAX; i++) {
+		priv->enable_gpios[i] = devm_gpiod_get_index_optional(&i2c->dev,
+								      "enable",
+								      i,
+								      GPIOD_OUT_HIGH);
+		if (IS_ERR(priv->enable_gpios[i])) {
+			dev_err(&i2c->dev, "Failed to get gpios\n");
+			return PTR_ERR(priv->enable_gpios[i]);
+		}
 	}
 
 	for (i = 0; i < DSV_OUT_MAX; i++) {

drivers/regulator/rt5759-regulator.c

+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/bits.h>
+#include <linux/i2c.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+#define RT5759_REG_VENDORINFO	0x00
+#define RT5759_REG_FREQ		0x01
+#define RT5759_REG_VSEL		0x02
+#define RT5759_REG_DCDCCTRL	0x03
+#define RT5759_REG_STATUS	0x04
+#define RT5759_REG_DCDCSET	0x05
+#define RT5759A_REG_WDTEN	0x42
+
+#define RT5759_TSTEP_MASK	GENMASK(3, 2)
+#define RT5759_VSEL_MASK	GENMASK(6, 0)
+#define RT5759_DISCHARGE_MASK	BIT(3)
+#define RT5759_FPWM_MASK	BIT(2)
+#define RT5759_ENABLE_MASK	BIT(1)
+#define RT5759_OT_MASK		BIT(1)
+#define RT5759_UV_MASK		BIT(0)
+#define RT5957_OCLVL_MASK	GENMASK(7, 6)
+#define RT5759_OCLVL_SHIFT	6
+#define RT5957_OTLVL_MASK	GENMASK(5, 4)
+#define RT5759_OTLVL_SHIFT	4
+#define RT5759A_WDTEN_MASK	BIT(1)
+
+#define RT5759_MANUFACTURER_ID	0x82
+/* vsel range 0x00 ~ 0x5A */
+#define RT5759_NUM_VOLTS	91
+#define RT5759_MIN_UV		600000
+#define RT5759_STEP_UV		10000
+#define RT5759A_STEP_UV		12500
+#define RT5759_MINSS_TIMEUS	1500
+
+#define RT5759_PSKIP_MODE	0
+#define RT5759_FPWM_MODE	1
+
+enum {
+	CHIP_TYPE_RT5759 = 0,
+	CHIP_TYPE_RT5759A,
+	CHIP_TYPE_MAX
+};
+
+struct rt5759_priv {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_desc desc;
+	unsigned long chip_type;
+};
+
+static int rt5759_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int mode_val;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		mode_val = 0;
+		break;
+	case REGULATOR_MODE_FAST:
+		mode_val = RT5759_FPWM_MASK;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(regmap, RT5759_REG_STATUS, RT5759_FPWM_MASK,
+				  mode_val);
+}
+
+static unsigned int rt5759_get_mode(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int regval;
+	int ret;
+
+	ret = regmap_read(regmap, RT5759_REG_DCDCCTRL, &regval);
+	if (ret)
+		return REGULATOR_MODE_INVALID;
+
+	if (regval & RT5759_FPWM_MASK)
+		return REGULATOR_MODE_FAST;
+
+	return REGULATOR_MODE_NORMAL;
+}
+
+static int rt5759_get_error_flags(struct regulator_dev *rdev,
+				  unsigned int *flags)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int status, events = 0;
+	int ret;
+
+	ret = regmap_read(regmap, RT5759_REG_STATUS, &status);
+	if (ret)
+		return ret;
+
+	if (status & RT5759_OT_MASK)
+		events |= REGULATOR_ERROR_OVER_TEMP;
+
+	if (status & RT5759_UV_MASK)
+		events |= REGULATOR_ERROR_UNDER_VOLTAGE;
+
+	*flags = events;
+	return 0;
+}
+
+static int rt5759_set_ocp(struct regulator_dev *rdev, int lim_uA, int severity,
+			  bool enable)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int ocp_lvl[] = { 9800000, 10800000, 11800000 };
+	unsigned int ocp_regval;
+	int i;
+
+	/* Only support over current protection parameter */
+	if (severity != REGULATOR_SEVERITY_PROT)
+		return 0;
+
+	if (enable) {
+		/* Default ocp level is 10.8A */
+		if (lim_uA == 0)
+			lim_uA = 10800000;
+
+		for (i = 0; i < ARRAY_SIZE(ocp_lvl); i++) {
+			if (lim_uA <= ocp_lvl[i])
+				break;
+		}
+
+		if (i == ARRAY_SIZE(ocp_lvl))
+			i = ARRAY_SIZE(ocp_lvl) - 1;
+
+		ocp_regval = i + 1;
+	} else
+		ocp_regval = 0;
+
+	return regmap_update_bits(regmap, RT5759_REG_DCDCSET, RT5957_OCLVL_MASK,
+				  ocp_regval << RT5759_OCLVL_SHIFT);
+}
+
+static int rt5759_set_otp(struct regulator_dev *rdev, int lim, int severity,
+			  bool enable)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int otp_lvl[] = { 140, 150, 170 };
+	unsigned int otp_regval;
+	int i;
+
+	/* Only support over temperature protection parameter */
+	if (severity != REGULATOR_SEVERITY_PROT)
+		return 0;
+
+	if (enable) {
+		/* Default otp level is 150'c */
+		if (lim == 0)
+			lim = 150;
+
+		for (i = 0; i < ARRAY_SIZE(otp_lvl); i++) {
+			if (lim <= otp_lvl[i])
+				break;
+		}
+
+		if (i == ARRAY_SIZE(otp_lvl))
+			i = ARRAY_SIZE(otp_lvl) - 1;
+
+		otp_regval = i + 1;
+	} else
+		otp_regval = 0;
+
+	return regmap_update_bits(regmap, RT5759_REG_DCDCSET, RT5957_OTLVL_MASK,
+				  otp_regval << RT5759_OTLVL_SHIFT);
+}
+
+static const struct regulator_ops rt5759_regulator_ops = {
+	.list_voltage = regulator_list_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.set_mode = rt5759_set_mode,
+	.get_mode = rt5759_get_mode,
+	.set_ramp_delay = regulator_set_ramp_delay_regmap,
+	.get_error_flags = rt5759_get_error_flags,
+	.set_over_current_protection = rt5759_set_ocp,
+	.set_thermal_protection = rt5759_set_otp,
+};
+
+static unsigned int rt5759_of_map_mode(unsigned int mode)
+{
+	switch (mode) {
+	case RT5759_FPWM_MODE:
+		return REGULATOR_MODE_FAST;
+	case RT5759_PSKIP_MODE:
+		return REGULATOR_MODE_NORMAL;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+static const unsigned int rt5759_ramp_table[] = { 20000, 15000, 10000, 5000 };
+
+static int rt5759_regulator_register(struct rt5759_priv *priv)
+{
+	struct device_node *np = priv->dev->of_node;
+	struct regulator_desc *reg_desc = &priv->desc;
+	struct regulator_config reg_cfg;
+	struct regulator_dev *rdev;
+	int ret;
+
+	reg_desc->name = "rt5759-buck";
+	reg_desc->type = REGULATOR_VOLTAGE;
+	reg_desc->owner = THIS_MODULE;
+	reg_desc->ops = &rt5759_regulator_ops;
+	reg_desc->n_voltages = RT5759_NUM_VOLTS;
+	reg_desc->min_uV = RT5759_MIN_UV;
+	reg_desc->uV_step = RT5759_STEP_UV;
+	reg_desc->vsel_reg = RT5759_REG_VSEL;
+	reg_desc->vsel_mask = RT5759_VSEL_MASK;
+	reg_desc->enable_reg = RT5759_REG_DCDCCTRL;
+	reg_desc->enable_mask = RT5759_ENABLE_MASK;
+	reg_desc->active_discharge_reg = RT5759_REG_DCDCCTRL;
+	reg_desc->active_discharge_mask = RT5759_DISCHARGE_MASK;
+	reg_desc->active_discharge_on = RT5759_DISCHARGE_MASK;
+	reg_desc->ramp_reg = RT5759_REG_FREQ;
+	reg_desc->ramp_mask = RT5759_TSTEP_MASK;
+	reg_desc->ramp_delay_table = rt5759_ramp_table;
+	reg_desc->n_ramp_values = ARRAY_SIZE(rt5759_ramp_table);
+	reg_desc->enable_time = RT5759_MINSS_TIMEUS;
+	reg_desc->of_map_mode = rt5759_of_map_mode;
+
+	/*
+	 * RT5759 step uV = 10000
+	 * RT5759A step uV = 12500
+	 */
+	if (priv->chip_type == CHIP_TYPE_RT5759A)
+		reg_desc->uV_step = RT5759A_STEP_UV;
+
+	reg_cfg.dev = priv->dev;
+	reg_cfg.of_node = np;
+	reg_cfg.init_data = of_get_regulator_init_data(priv->dev, np, reg_desc);
+	reg_cfg.regmap = priv->regmap;
+
+	rdev = devm_regulator_register(priv->dev, reg_desc, &reg_cfg);
+	if (IS_ERR(rdev)) {
+		ret = PTR_ERR(rdev);
+		dev_err(priv->dev, "Failed to register regulator (%d)\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static int rt5759_init_device_property(struct rt5759_priv *priv)
+{
+	unsigned int val = 0;
+
+	/*
+	 * Only RT5759A support external watchdog input
+	 */
+	if (priv->chip_type != CHIP_TYPE_RT5759A)
+		return 0;
+
+	if (device_property_read_bool(priv->dev, "richtek,watchdog-enable"))
+		val = RT5759A_WDTEN_MASK;
+
+	return regmap_update_bits(priv->regmap, RT5759A_REG_WDTEN,
+				  RT5759A_WDTEN_MASK, val);
+}
+
+static int rt5759_manufacturer_check(struct rt5759_priv *priv)
+{
+	unsigned int vendor;
+	int ret;
+
+	ret = regmap_read(priv->regmap, RT5759_REG_VENDORINFO, &vendor);
+	if (ret)
+		return ret;
+
+	if (vendor != RT5759_MANUFACTURER_ID) {
+		dev_err(priv->dev, "vendor info not correct (%d)\n", vendor);
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+static bool rt5759_is_accessible_reg(struct device *dev, unsigned int reg)
+{
+	struct rt5759_priv *priv = dev_get_drvdata(dev);
+
+	if (reg <= RT5759_REG_DCDCSET)
+		return true;
+
+	if (priv->chip_type == CHIP_TYPE_RT5759A && reg == RT5759A_REG_WDTEN)
+		return true;
+
+	return false;
+}
+
+static const struct regmap_config rt5759_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = RT5759A_REG_WDTEN,
+	.readable_reg = rt5759_is_accessible_reg,
+	.writeable_reg = rt5759_is_accessible_reg,
+};
+
+static int rt5759_probe(struct i2c_client *i2c)
+{
+	struct rt5759_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&i2c->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &i2c->dev;
+	priv->chip_type = (unsigned long)of_device_get_match_data(&i2c->dev);
+	i2c_set_clientdata(i2c, priv);
+
+	priv->regmap = devm_regmap_init_i2c(i2c, &rt5759_regmap_config);
+	if (IS_ERR(priv->regmap)) {
+		ret = PTR_ERR(priv->regmap);
+		dev_err(&i2c->dev, "Failed to allocate regmap (%d)\n", ret);
+		return ret;
+	}
+
+	ret = rt5759_manufacturer_check(priv);
+	if (ret) {
+		dev_err(&i2c->dev, "Failed to check device (%d)\n", ret);
+		return ret;
+	}
+
+	ret = rt5759_init_device_property(priv);
+	if (ret) {
+		dev_err(&i2c->dev, "Failed to init device (%d)\n", ret);
+		return ret;
+	}
+
+	return rt5759_regulator_register(priv);
+}
+
+static const struct of_device_id __maybe_unused rt5759_device_table[] = {
+	{ .compatible = "richtek,rt5759", .data = (void *)CHIP_TYPE_RT5759 },
+	{ .compatible = "richtek,rt5759a", .data = (void *)CHIP_TYPE_RT5759A },
+	{}
+};
+MODULE_DEVICE_TABLE(of, rt5759_device_table);
+
+static struct i2c_driver rt5759_driver = {
+	.driver = {
+		.name = "rt5759",
+		.of_match_table = of_match_ptr(rt5759_device_table),
+	},
+	.probe_new = rt5759_probe,
+};
+module_i2c_driver(rt5759_driver);
+
+MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>");
+MODULE_DESCRIPTION("Richtek RT5759 Regulator Driver");
+MODULE_LICENSE("GPL v2");

drivers/regulator/scmi-regulator.c

@@ -352,7 +352,7 @@ static int scmi_regulator_probe(struct scmi_device *sdev)
 			return ret;
 		}
 	}
-
+	of_node_put(np);
 	/*
 	 * Register a regulator for each valid regulator-DT-entry that we
 	 * can successfully reach via SCMI and has a valid associated voltage

drivers/regulator/sm5703-regulator.c

+// SPDX-License-Identifier: GPL-2.0-only
+
+#include <linux/mfd/sm5703.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/of_regulator.h>
+
+enum sm5703_regulators {
+	SM5703_BUCK,
+	SM5703_LDO1,
+	SM5703_LDO2,
+	SM5703_LDO3,
+	SM5703_USBLDO1,
+	SM5703_USBLDO2,
+	SM5703_VBUS,
+	SM5703_MAX_REGULATORS,
+};
+
+static const int sm5703_ldo_voltagemap[] = {
+	1500000, 1800000, 2600000, 2800000, 3000000, 3300000,
+};
+
+static const int sm5703_buck_voltagemap[] = {
+	1000000, 1000000, 1000000, 1000000,
+	1000000, 1000000, 1000000, 1000000,
+	1000000, 1000000, 1000000, 1100000,
+	1200000, 1300000, 1400000, 1500000,
+	1600000, 1700000, 1800000, 1900000,
+	2000000, 2100000, 2200000, 2300000,
+	2400000, 2500000, 2600000, 2700000,
+	2800000, 2900000, 3000000, 3000000,
+};
+
+#define SM5703USBLDO(_name, _id)					\
+	[SM5703_USBLDO ## _id] = {					\
+		.name = _name,						\
+		.of_match = _name,					\
+		.regulators_node = "regulators",			\
+		.type = REGULATOR_VOLTAGE,				\
+		.id = SM5703_USBLDO ## _id,				\
+		.ops = &sm5703_regulator_ops_fixed,			\
+		.fixed_uV = SM5703_USBLDO_MICROVOLT,			\
+		.enable_reg = SM5703_REG_USBLDO12,			\
+		.enable_mask = SM5703_REG_EN_USBLDO ##_id,		\
+		.owner			= THIS_MODULE,			\
+	}
+
+#define SM5703VBUS(_name)						\
+	[SM5703_VBUS] = {						\
+		.name = _name,						\
+		.of_match = _name,					\
+		.regulators_node = "regulators",			\
+		.type = REGULATOR_VOLTAGE,				\
+		.id = SM5703_VBUS,					\
+		.ops = &sm5703_regulator_ops_fixed,			\
+		.fixed_uV = SM5703_VBUS_MICROVOLT,			\
+		.enable_reg = SM5703_REG_CNTL,				\
+		.enable_mask = SM5703_OPERATION_MODE_MASK,		\
+		.enable_val = SM5703_OPERATION_MODE_USB_OTG_MODE,	\
+		.disable_val = SM5703_OPERATION_MODE_CHARGING_ON,	\
+		.owner			= THIS_MODULE,			\
+	}
+
+#define SM5703BUCK(_name)						\
+	[SM5703_BUCK] = {						\
+		.name = _name,						\
+		.of_match = _name,					\
+		.regulators_node = "regulators",			\
+		.type = REGULATOR_VOLTAGE,				\
+		.id = SM5703_BUCK,					\
+		.ops = &sm5703_regulator_ops,				\
+		.n_voltages = ARRAY_SIZE(sm5703_buck_voltagemap),	\
+		.volt_table = sm5703_buck_voltagemap,			\
+		.vsel_reg = SM5703_REG_BUCK,				\
+		.vsel_mask = SM5703_BUCK_VOLT_MASK,			\
+		.enable_reg = SM5703_REG_BUCK,				\
+		.enable_mask = SM5703_REG_EN_BUCK,			\
+		.owner			= THIS_MODULE,			\
+	}
+
+#define SM5703LDO(_name, _id)						\
+	[SM5703_LDO ## _id] = {						\
+		.name = _name,						\
+		.of_match = _name,					\
+		.regulators_node = "regulators",			\
+		.type = REGULATOR_VOLTAGE,				\
+		.id = SM5703_LDO ## _id,				\
+		.ops = &sm5703_regulator_ops,				\
+		.n_voltages = ARRAY_SIZE(sm5703_ldo_voltagemap),	\
+		.volt_table = sm5703_ldo_voltagemap,			\
+		.vsel_reg = SM5703_REG_LDO ##_id,			\
+		.vsel_mask = SM5703_LDO_VOLT_MASK,			\
+		.enable_reg = SM5703_REG_LDO ##_id,			\
+		.enable_mask = SM5703_LDO_EN,				\
+		.owner			= THIS_MODULE,			\
+	}
+
+static const struct regulator_ops sm5703_regulator_ops = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+	.list_voltage		= regulator_list_voltage_table,
+	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
+	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
+};
+
+static const struct regulator_ops sm5703_regulator_ops_fixed = {
+	.enable			= regulator_enable_regmap,
+	.disable		= regulator_disable_regmap,
+	.is_enabled		= regulator_is_enabled_regmap,
+};
+
+static struct regulator_desc sm5703_regulators_desc[SM5703_MAX_REGULATORS] = {
+	SM5703BUCK("buck"),
+	SM5703LDO("ldo1", 1),
+	SM5703LDO("ldo2", 2),
+	SM5703LDO("ldo3", 3),
+	SM5703USBLDO("usbldo1", 1),
+	SM5703USBLDO("usbldo2", 2),
+	SM5703VBUS("vbus"),
+};
+
+static int sm5703_regulator_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct regulator_config config = { NULL, };
+	struct regulator_dev *rdev;
+	struct sm5703_dev *sm5703 = dev_get_drvdata(pdev->dev.parent);
+	int i;
+
+	config.dev = dev->parent;
+	config.regmap = sm5703->regmap;
+
+	for (i = 0; i < SM5703_MAX_REGULATORS; i++) {
+		rdev = devm_regulator_register(dev,
+					       &sm5703_regulators_desc[i],
+					       &config);
+		if (IS_ERR(rdev))
+			return dev_err_probe(dev, PTR_ERR(rdev),
+					     "Failed to register a regulator\n");
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id sm5703_regulator_id[] = {
+	{ "sm5703-regulator", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, sm5703_regulator_id);
+
+static struct platform_driver sm5703_regulator_driver = {
+	.driver = {
+		.name = "sm5703-regulator",
+	},
+	.probe	= sm5703_regulator_probe,
+	.id_table	= sm5703_regulator_id,
+};
+
+module_platform_driver(sm5703_regulator_driver);
+
+MODULE_DESCRIPTION("Silicon Mitus SM5703 LDO/Buck/USB regulator driver");
+MODULE_AUTHOR("Markuss Broks <markuss.broks@gmail.com>");
+MODULE_LICENSE("GPL");

drivers/regulator/stm32-vrefbuf.c

@@ -44,11 +44,9 @@ static int stm32_vrefbuf_enable(struct regulator_dev *rdev)
 	u32 val;
 	int ret;
 
-	ret = pm_runtime_get_sync(priv->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(priv->dev);
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val = (val & ~STM32_HIZ) | STM32_ENVR;
@@ -81,11 +79,9 @@ static int stm32_vrefbuf_disable(struct regulator_dev *rdev)
 	u32 val;
 	int ret;
 
-	ret = pm_runtime_get_sync(priv->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(priv->dev);
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val &= ~STM32_ENVR;
@@ -102,11 +98,9 @@ static int stm32_vrefbuf_is_enabled(struct regulator_dev *rdev)
 	struct stm32_vrefbuf *priv = rdev_get_drvdata(rdev);
 	int ret;
 
-	ret = pm_runtime_get_sync(priv->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(priv->dev);
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	ret = readl_relaxed(priv->base + STM32_VREFBUF_CSR) & STM32_ENVR;
 
@@ -123,11 +117,9 @@ static int stm32_vrefbuf_set_voltage_sel(struct regulator_dev *rdev,
 	u32 val;
 	int ret;
 
-	ret = pm_runtime_get_sync(priv->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(priv->dev);
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	val = (val & ~STM32_VRS) | FIELD_PREP(STM32_VRS, sel);
@@ -145,11 +137,9 @@ static int stm32_vrefbuf_get_voltage_sel(struct regulator_dev *rdev)
 	u32 val;
 	int ret;
 
-	ret = pm_runtime_get_sync(priv->dev);
-	if (ret < 0) {
-		pm_runtime_put_noidle(priv->dev);
+	ret = pm_runtime_resume_and_get(priv->dev);
+	if (ret < 0)
 		return ret;
-	}
 
 	val = readl_relaxed(priv->base + STM32_VREFBUF_CSR);
 	ret = FIELD_GET(STM32_VRS, val);

include/linux/regulator/mt6358-regulator.h

@@ -48,9 +48,54 @@ enum {
 	MT6358_ID_VLDO28,
 	MT6358_ID_VAUD28,
 	MT6358_ID_VSIM2,
+	MT6358_ID_VCORE_SSHUB,
+	MT6358_ID_VSRAM_OTHERS_SSHUB,
 	MT6358_ID_RG_MAX,
 };
 
+enum {
+	MT6366_ID_VDRAM1 = 0,
+	MT6366_ID_VCORE,
+	MT6366_ID_VPA,
+	MT6366_ID_VPROC11,
+	MT6366_ID_VPROC12,
+	MT6366_ID_VGPU,
+	MT6366_ID_VS2,
+	MT6366_ID_VMODEM,
+	MT6366_ID_VS1,
+	MT6366_ID_VDRAM2,
+	MT6366_ID_VSIM1,
+	MT6366_ID_VIBR,
+	MT6366_ID_VRF12,
+	MT6366_ID_VIO18,
+	MT6366_ID_VUSB,
+	MT6366_ID_VCN18,
+	MT6366_ID_VFE28,
+	MT6366_ID_VSRAM_PROC11,
+	MT6366_ID_VCN28,
+	MT6366_ID_VSRAM_OTHERS,
+	MT6366_ID_VSRAM_GPU,
+	MT6366_ID_VXO22,
+	MT6366_ID_VEFUSE,
+	MT6366_ID_VAUX18,
+	MT6366_ID_VMCH,
+	MT6366_ID_VBIF28,
+	MT6366_ID_VSRAM_PROC12,
+	MT6366_ID_VEMC,
+	MT6366_ID_VIO28,
+	MT6366_ID_VA12,
+	MT6366_ID_VRF18,
+	MT6366_ID_VCN33_BT,
+	MT6366_ID_VCN33_WIFI,
+	MT6366_ID_VMC,
+	MT6366_ID_VAUD28,
+	MT6366_ID_VSIM2,
+	MT6366_ID_VCORE_SSHUB,
+	MT6366_ID_VSRAM_OTHERS_SSHUB,
+	MT6366_ID_RG_MAX,
+};
+
 #define MT6358_MAX_REGULATOR	MT6358_ID_RG_MAX
+#define MT6366_MAX_REGULATOR	MT6366_ID_RG_MAX
 
 #endif /* __LINUX_REGULATOR_MT6358_H */

include/linux/regulator/pca9450.h

@@ -226,4 +226,11 @@ enum {
 #define WDOG_B_CFG_COLD_LDO12		0x80
 #define WDOG_B_CFG_COLD			0xC0
 
+/* PCA9450_REG_CONFIG2 bits */
+#define I2C_LT_MASK			0x03
+#define I2C_LT_FORCE_DISABLE		0x00
+#define I2C_LT_ON_STANDBY_RUN		0x01
+#define I2C_LT_ON_RUN			0x02
+#define I2C_LT_FORCE_ENABLE		0x03
+
 #endif /* __LINUX_REG_PCA9450_H__ */