Commit 9c3e7375 authored by Cliff Cai's avatar Cliff Cai Committed by Grant Likely

spi/spi_bfin_sport: new driver for a SPI bus via the Blackfin SPORT peripheral

The Blackfin SPORT peripheral is a pretty flexible device.  With enough
coaching, we can make it generate SPI compatible waveforms.  This is
desirable as the SPORT can run at much higher clock frequencies than the
dedicated on-chip SPI peripheral, and it can do full duplex DMA.  It also
opens up the possibility of multiple SPI buses in case someone wants to
dedicate a whole bus to a specific part that does not play well with
others.
Signed-off-by: default avatarCliff Cai <cliff.cai@analog.com>
Signed-off-by: default avatarBryan Wu <cooloney@kernel.org>
Signed-off-by: default avatarMichael Hennerich <michael.hennerich@analog.com>
Signed-off-by: default avatarMike Frysinger <vapier@gentoo.org>
Signed-off-by: default avatarGrant Likely <grant.likely@secretlab.ca>
parent 80b40370
......@@ -80,6 +80,15 @@ config SPI_BFIN
help
This is the SPI controller master driver for Blackfin 5xx processor.
config SPI_BFIN_SPORT
tristate "SPI bus via Blackfin SPORT"
depends on BLACKFIN
help
Enable support for a SPI bus via the Blackfin SPORT peripheral.
This driver can also be built as a module. If so, the module
will be called spi_bfin_sport.
config SPI_AU1550
tristate "Au1550/Au12x0 SPI Controller"
depends on (SOC_AU1550 || SOC_AU1200) && EXPERIMENTAL
......
......@@ -13,6 +13,7 @@ obj-$(CONFIG_SPI_ALTERA) += spi_altera.o
obj-$(CONFIG_SPI_ATMEL) += atmel_spi.o
obj-$(CONFIG_SPI_ATH79) += ath79_spi.o
obj-$(CONFIG_SPI_BFIN) += spi_bfin5xx.o
obj-$(CONFIG_SPI_BFIN_SPORT) += spi_bfin_sport.o
obj-$(CONFIG_SPI_BITBANG) += spi_bitbang.o
obj-$(CONFIG_SPI_AU1550) += au1550_spi.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi_butterfly.o
......
/*
* SPI bus via the Blackfin SPORT peripheral
*
* Enter bugs at http://blackfin.uclinux.org/
*
* Copyright 2009-2011 Analog Devices Inc.
*
* Licensed under the GPL-2 or later.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/delay.h>
#include <linux/device.h>
#include <linux/gpio.h>
#include <linux/io.h>
#include <linux/ioport.h>
#include <linux/irq.h>
#include <linux/errno.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/workqueue.h>
#include <asm/portmux.h>
#include <asm/bfin5xx_spi.h>
#include <asm/blackfin.h>
#include <asm/bfin_sport.h>
#include <asm/cacheflush.h>
#define DRV_NAME "bfin-sport-spi"
#define DRV_DESC "SPI bus via the Blackfin SPORT"
MODULE_AUTHOR("Cliff Cai");
MODULE_DESCRIPTION(DRV_DESC);
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:bfin-sport-spi");
enum bfin_sport_spi_state {
START_STATE,
RUNNING_STATE,
DONE_STATE,
ERROR_STATE,
};
struct bfin_sport_spi_master_data;
struct bfin_sport_transfer_ops {
void (*write) (struct bfin_sport_spi_master_data *);
void (*read) (struct bfin_sport_spi_master_data *);
void (*duplex) (struct bfin_sport_spi_master_data *);
};
struct bfin_sport_spi_master_data {
/* Driver model hookup */
struct device *dev;
/* SPI framework hookup */
struct spi_master *master;
/* Regs base of SPI controller */
struct sport_register __iomem *regs;
int err_irq;
/* Pin request list */
u16 *pin_req;
/* Driver message queue */
struct workqueue_struct *workqueue;
struct work_struct pump_messages;
spinlock_t lock;
struct list_head queue;
int busy;
bool run;
/* Message Transfer pump */
struct tasklet_struct pump_transfers;
/* Current message transfer state info */
enum bfin_sport_spi_state state;
struct spi_message *cur_msg;
struct spi_transfer *cur_transfer;
struct bfin_sport_spi_slave_data *cur_chip;
union {
void *tx;
u8 *tx8;
u16 *tx16;
};
void *tx_end;
union {
void *rx;
u8 *rx8;
u16 *rx16;
};
void *rx_end;
int cs_change;
struct bfin_sport_transfer_ops *ops;
};
struct bfin_sport_spi_slave_data {
u16 ctl_reg;
u16 baud;
u16 cs_chg_udelay; /* Some devices require > 255usec delay */
u32 cs_gpio;
u16 idle_tx_val;
struct bfin_sport_transfer_ops *ops;
};
static void
bfin_sport_spi_enable(struct bfin_sport_spi_master_data *drv_data)
{
bfin_write_or(&drv_data->regs->tcr1, TSPEN);
bfin_write_or(&drv_data->regs->rcr1, TSPEN);
SSYNC();
}
static void
bfin_sport_spi_disable(struct bfin_sport_spi_master_data *drv_data)
{
bfin_write_and(&drv_data->regs->tcr1, ~TSPEN);
bfin_write_and(&drv_data->regs->rcr1, ~TSPEN);
SSYNC();
}
/* Caculate the SPI_BAUD register value based on input HZ */
static u16
bfin_sport_hz_to_spi_baud(u32 speed_hz)
{
u_long clk, sclk = get_sclk();
int div = (sclk / (2 * speed_hz)) - 1;
if (div < 0)
div = 0;
clk = sclk / (2 * (div + 1));
if (clk > speed_hz)
div++;
return div;
}
/* Chip select operation functions for cs_change flag */
static void
bfin_sport_spi_cs_active(struct bfin_sport_spi_slave_data *chip)
{
gpio_direction_output(chip->cs_gpio, 0);
}
static void
bfin_sport_spi_cs_deactive(struct bfin_sport_spi_slave_data *chip)
{
gpio_direction_output(chip->cs_gpio, 1);
/* Move delay here for consistency */
if (chip->cs_chg_udelay)
udelay(chip->cs_chg_udelay);
}
static void
bfin_sport_spi_stat_poll_complete(struct bfin_sport_spi_master_data *drv_data)
{
unsigned long timeout = jiffies + HZ;
while (!(bfin_read(&drv_data->regs->stat) & RXNE)) {
if (!time_before(jiffies, timeout))
break;
}
}
static void
bfin_sport_spi_u8_writer(struct bfin_sport_spi_master_data *drv_data)
{
u16 dummy;
while (drv_data->tx < drv_data->tx_end) {
bfin_write(&drv_data->regs->tx16, *drv_data->tx8++);
bfin_sport_spi_stat_poll_complete(drv_data);
dummy = bfin_read(&drv_data->regs->rx16);
}
}
static void
bfin_sport_spi_u8_reader(struct bfin_sport_spi_master_data *drv_data)
{
u16 tx_val = drv_data->cur_chip->idle_tx_val;
while (drv_data->rx < drv_data->rx_end) {
bfin_write(&drv_data->regs->tx16, tx_val);
bfin_sport_spi_stat_poll_complete(drv_data);
*drv_data->rx8++ = bfin_read(&drv_data->regs->rx16);
}
}
static void
bfin_sport_spi_u8_duplex(struct bfin_sport_spi_master_data *drv_data)
{
while (drv_data->rx < drv_data->rx_end) {
bfin_write(&drv_data->regs->tx16, *drv_data->tx8++);
bfin_sport_spi_stat_poll_complete(drv_data);
*drv_data->rx8++ = bfin_read(&drv_data->regs->rx16);
}
}
static struct bfin_sport_transfer_ops bfin_sport_transfer_ops_u8 = {
.write = bfin_sport_spi_u8_writer,
.read = bfin_sport_spi_u8_reader,
.duplex = bfin_sport_spi_u8_duplex,
};
static void
bfin_sport_spi_u16_writer(struct bfin_sport_spi_master_data *drv_data)
{
u16 dummy;
while (drv_data->tx < drv_data->tx_end) {
bfin_write(&drv_data->regs->tx16, *drv_data->tx16++);
bfin_sport_spi_stat_poll_complete(drv_data);
dummy = bfin_read(&drv_data->regs->rx16);
}
}
static void
bfin_sport_spi_u16_reader(struct bfin_sport_spi_master_data *drv_data)
{
u16 tx_val = drv_data->cur_chip->idle_tx_val;
while (drv_data->rx < drv_data->rx_end) {
bfin_write(&drv_data->regs->tx16, tx_val);
bfin_sport_spi_stat_poll_complete(drv_data);
*drv_data->rx16++ = bfin_read(&drv_data->regs->rx16);
}
}
static void
bfin_sport_spi_u16_duplex(struct bfin_sport_spi_master_data *drv_data)
{
while (drv_data->rx < drv_data->rx_end) {
bfin_write(&drv_data->regs->tx16, *drv_data->tx16++);
bfin_sport_spi_stat_poll_complete(drv_data);
*drv_data->rx16++ = bfin_read(&drv_data->regs->rx16);
}
}
static struct bfin_sport_transfer_ops bfin_sport_transfer_ops_u16 = {
.write = bfin_sport_spi_u16_writer,
.read = bfin_sport_spi_u16_reader,
.duplex = bfin_sport_spi_u16_duplex,
};
/* stop controller and re-config current chip */
static void
bfin_sport_spi_restore_state(struct bfin_sport_spi_master_data *drv_data)
{
struct bfin_sport_spi_slave_data *chip = drv_data->cur_chip;
unsigned int bits = (drv_data->ops == &bfin_sport_transfer_ops_u8 ? 7 : 15);
bfin_sport_spi_disable(drv_data);
dev_dbg(drv_data->dev, "restoring spi ctl state\n");
bfin_write(&drv_data->regs->tcr1, chip->ctl_reg);
bfin_write(&drv_data->regs->tcr2, bits);
bfin_write(&drv_data->regs->tclkdiv, chip->baud);
bfin_write(&drv_data->regs->tfsdiv, bits);
SSYNC();
bfin_write(&drv_data->regs->rcr1, chip->ctl_reg & ~(ITCLK | ITFS));
bfin_write(&drv_data->regs->rcr2, bits);
SSYNC();
bfin_sport_spi_cs_active(chip);
}
/* test if there is more transfer to be done */
static enum bfin_sport_spi_state
bfin_sport_spi_next_transfer(struct bfin_sport_spi_master_data *drv_data)
{
struct spi_message *msg = drv_data->cur_msg;
struct spi_transfer *trans = drv_data->cur_transfer;
/* Move to next transfer */
if (trans->transfer_list.next != &msg->transfers) {
drv_data->cur_transfer =
list_entry(trans->transfer_list.next,
struct spi_transfer, transfer_list);
return RUNNING_STATE;
}
return DONE_STATE;
}
/*
* caller already set message->status;
* dma and pio irqs are blocked give finished message back
*/
static void
bfin_sport_spi_giveback(struct bfin_sport_spi_master_data *drv_data)
{
struct bfin_sport_spi_slave_data *chip = drv_data->cur_chip;
unsigned long flags;
struct spi_message *msg;
spin_lock_irqsave(&drv_data->lock, flags);
msg = drv_data->cur_msg;
drv_data->state = START_STATE;
drv_data->cur_msg = NULL;
drv_data->cur_transfer = NULL;
drv_data->cur_chip = NULL;
queue_work(drv_data->workqueue, &drv_data->pump_messages);
spin_unlock_irqrestore(&drv_data->lock, flags);
if (!drv_data->cs_change)
bfin_sport_spi_cs_deactive(chip);
if (msg->complete)
msg->complete(msg->context);
}
static irqreturn_t
sport_err_handler(int irq, void *dev_id)
{
struct bfin_sport_spi_master_data *drv_data = dev_id;
u16 status;
dev_dbg(drv_data->dev, "%s enter\n", __func__);
status = bfin_read(&drv_data->regs->stat) & (TOVF | TUVF | ROVF | RUVF);
if (status) {
bfin_write(&drv_data->regs->stat, status);
SSYNC();
bfin_sport_spi_disable(drv_data);
dev_err(drv_data->dev, "status error:%s%s%s%s\n",
status & TOVF ? " TOVF" : "",
status & TUVF ? " TUVF" : "",
status & ROVF ? " ROVF" : "",
status & RUVF ? " RUVF" : "");
}
return IRQ_HANDLED;
}
static void
bfin_sport_spi_pump_transfers(unsigned long data)
{
struct bfin_sport_spi_master_data *drv_data = (void *)data;
struct spi_message *message = NULL;
struct spi_transfer *transfer = NULL;
struct spi_transfer *previous = NULL;
struct bfin_sport_spi_slave_data *chip = NULL;
unsigned int bits_per_word;
u32 tranf_success = 1;
u32 transfer_speed;
u8 full_duplex = 0;
/* Get current state information */
message = drv_data->cur_msg;
transfer = drv_data->cur_transfer;
chip = drv_data->cur_chip;
if (transfer->speed_hz)
transfer_speed = bfin_sport_hz_to_spi_baud(transfer->speed_hz);
else
transfer_speed = chip->baud;
bfin_write(&drv_data->regs->tclkdiv, transfer_speed);
SSYNC();
/*
* if msg is error or done, report it back using complete() callback
*/
/* Handle for abort */
if (drv_data->state == ERROR_STATE) {
dev_dbg(drv_data->dev, "transfer: we've hit an error\n");
message->status = -EIO;
bfin_sport_spi_giveback(drv_data);
return;
}
/* Handle end of message */
if (drv_data->state == DONE_STATE) {
dev_dbg(drv_data->dev, "transfer: all done!\n");
message->status = 0;
bfin_sport_spi_giveback(drv_data);
return;
}
/* Delay if requested at end of transfer */
if (drv_data->state == RUNNING_STATE) {
dev_dbg(drv_data->dev, "transfer: still running ...\n");
previous = list_entry(transfer->transfer_list.prev,
struct spi_transfer, transfer_list);
if (previous->delay_usecs)
udelay(previous->delay_usecs);
}
if (transfer->len == 0) {
/* Move to next transfer of this msg */
drv_data->state = bfin_sport_spi_next_transfer(drv_data);
/* Schedule next transfer tasklet */
tasklet_schedule(&drv_data->pump_transfers);
}
if (transfer->tx_buf != NULL) {
drv_data->tx = (void *)transfer->tx_buf;
drv_data->tx_end = drv_data->tx + transfer->len;
dev_dbg(drv_data->dev, "tx_buf is %p, tx_end is %p\n",
transfer->tx_buf, drv_data->tx_end);
} else
drv_data->tx = NULL;
if (transfer->rx_buf != NULL) {
full_duplex = transfer->tx_buf != NULL;
drv_data->rx = transfer->rx_buf;
drv_data->rx_end = drv_data->rx + transfer->len;
dev_dbg(drv_data->dev, "rx_buf is %p, rx_end is %p\n",
transfer->rx_buf, drv_data->rx_end);
} else
drv_data->rx = NULL;
drv_data->cs_change = transfer->cs_change;
/* Bits per word setup */
bits_per_word = transfer->bits_per_word ? : message->spi->bits_per_word;
if (bits_per_word == 8)
drv_data->ops = &bfin_sport_transfer_ops_u8;
else
drv_data->ops = &bfin_sport_transfer_ops_u16;
drv_data->state = RUNNING_STATE;
if (drv_data->cs_change)
bfin_sport_spi_cs_active(chip);
dev_dbg(drv_data->dev,
"now pumping a transfer: width is %d, len is %d\n",
bits_per_word, transfer->len);
/* PIO mode write then read */
dev_dbg(drv_data->dev, "doing IO transfer\n");
bfin_sport_spi_enable(drv_data);
if (full_duplex) {
/* full duplex mode */
BUG_ON((drv_data->tx_end - drv_data->tx) !=
(drv_data->rx_end - drv_data->rx));
drv_data->ops->duplex(drv_data);
if (drv_data->tx != drv_data->tx_end)
tranf_success = 0;
} else if (drv_data->tx != NULL) {
/* write only half duplex */
drv_data->ops->write(drv_data);
if (drv_data->tx != drv_data->tx_end)
tranf_success = 0;
} else if (drv_data->rx != NULL) {
/* read only half duplex */
drv_data->ops->read(drv_data);
if (drv_data->rx != drv_data->rx_end)
tranf_success = 0;
}
bfin_sport_spi_disable(drv_data);
if (!tranf_success) {
dev_dbg(drv_data->dev, "IO write error!\n");
drv_data->state = ERROR_STATE;
} else {
/* Update total byte transfered */
message->actual_length += transfer->len;
/* Move to next transfer of this msg */
drv_data->state = bfin_sport_spi_next_transfer(drv_data);
if (drv_data->cs_change)
bfin_sport_spi_cs_deactive(chip);
}
/* Schedule next transfer tasklet */
tasklet_schedule(&drv_data->pump_transfers);
}
/* pop a msg from queue and kick off real transfer */
static void
bfin_sport_spi_pump_messages(struct work_struct *work)
{
struct bfin_sport_spi_master_data *drv_data;
unsigned long flags;
struct spi_message *next_msg;
drv_data = container_of(work, struct bfin_sport_spi_master_data, pump_messages);
/* Lock queue and check for queue work */
spin_lock_irqsave(&drv_data->lock, flags);
if (list_empty(&drv_data->queue) || !drv_data->run) {
/* pumper kicked off but no work to do */
drv_data->busy = 0;
spin_unlock_irqrestore(&drv_data->lock, flags);
return;
}
/* Make sure we are not already running a message */
if (drv_data->cur_msg) {
spin_unlock_irqrestore(&drv_data->lock, flags);
return;
}
/* Extract head of queue */
next_msg = list_entry(drv_data->queue.next,
struct spi_message, queue);
drv_data->cur_msg = next_msg;
/* Setup the SSP using the per chip configuration */
drv_data->cur_chip = spi_get_ctldata(drv_data->cur_msg->spi);
list_del_init(&drv_data->cur_msg->queue);
/* Initialize message state */
drv_data->cur_msg->state = START_STATE;
drv_data->cur_transfer = list_entry(drv_data->cur_msg->transfers.next,
struct spi_transfer, transfer_list);
bfin_sport_spi_restore_state(drv_data);
dev_dbg(drv_data->dev, "got a message to pump, "
"state is set to: baud %d, cs_gpio %i, ctl 0x%x\n",
drv_data->cur_chip->baud, drv_data->cur_chip->cs_gpio,
drv_data->cur_chip->ctl_reg);
dev_dbg(drv_data->dev,
"the first transfer len is %d\n",
drv_data->cur_transfer->len);
/* Mark as busy and launch transfers */
tasklet_schedule(&drv_data->pump_transfers);
drv_data->busy = 1;
spin_unlock_irqrestore(&drv_data->lock, flags);
}
/*
* got a msg to transfer, queue it in drv_data->queue.
* And kick off message pumper
*/
static int
bfin_sport_spi_transfer(struct spi_device *spi, struct spi_message *msg)
{
struct bfin_sport_spi_master_data *drv_data = spi_master_get_devdata(spi->master);
unsigned long flags;
spin_lock_irqsave(&drv_data->lock, flags);
if (!drv_data->run) {
spin_unlock_irqrestore(&drv_data->lock, flags);
return -ESHUTDOWN;
}
msg->actual_length = 0;
msg->status = -EINPROGRESS;
msg->state = START_STATE;
dev_dbg(&spi->dev, "adding an msg in transfer()\n");
list_add_tail(&msg->queue, &drv_data->queue);
if (drv_data->run && !drv_data->busy)
queue_work(drv_data->workqueue, &drv_data->pump_messages);
spin_unlock_irqrestore(&drv_data->lock, flags);
return 0;
}
/* Called every time common spi devices change state */
static int
bfin_sport_spi_setup(struct spi_device *spi)
{
struct bfin_sport_spi_slave_data *chip, *first = NULL;
int ret;
/* Only alloc (or use chip_info) on first setup */
chip = spi_get_ctldata(spi);
if (chip == NULL) {
struct bfin5xx_spi_chip *chip_info;
chip = first = kzalloc(sizeof(*chip), GFP_KERNEL);
if (!chip)
return -ENOMEM;
/* platform chip_info isn't required */
chip_info = spi->controller_data;
if (chip_info) {
/*
* DITFS and TDTYPE are only thing we don't set, but
* they probably shouldn't be changed by people.
*/
if (chip_info->ctl_reg || chip_info->enable_dma) {
ret = -EINVAL;
dev_err(&spi->dev, "don't set ctl_reg/enable_dma fields");
goto error;
}
chip->cs_chg_udelay = chip_info->cs_chg_udelay;
chip->idle_tx_val = chip_info->idle_tx_val;
spi->bits_per_word = chip_info->bits_per_word;
}
}
if (spi->bits_per_word != 8 && spi->bits_per_word != 16) {
ret = -EINVAL;
goto error;
}
/* translate common spi framework into our register
* following configure contents are same for tx and rx.
*/
if (spi->mode & SPI_CPHA)
chip->ctl_reg &= ~TCKFE;
else
chip->ctl_reg |= TCKFE;
if (spi->mode & SPI_LSB_FIRST)
chip->ctl_reg |= TLSBIT;
else
chip->ctl_reg &= ~TLSBIT;
/* Sport in master mode */
chip->ctl_reg |= ITCLK | ITFS | TFSR | LATFS | LTFS;
chip->baud = bfin_sport_hz_to_spi_baud(spi->max_speed_hz);
chip->cs_gpio = spi->chip_select;
ret = gpio_request(chip->cs_gpio, spi->modalias);
if (ret)
goto error;
dev_dbg(&spi->dev, "setup spi chip %s, width is %d\n",
spi->modalias, spi->bits_per_word);
dev_dbg(&spi->dev, "ctl_reg is 0x%x, GPIO is %i\n",
chip->ctl_reg, spi->chip_select);
spi_set_ctldata(spi, chip);
bfin_sport_spi_cs_deactive(chip);
return ret;
error:
kfree(first);
return ret;
}
/*
* callback for spi framework.
* clean driver specific data
*/
static void
bfin_sport_spi_cleanup(struct spi_device *spi)
{
struct bfin_sport_spi_slave_data *chip = spi_get_ctldata(spi);
if (!chip)
return;
gpio_free(chip->cs_gpio);
kfree(chip);
}
static int
bfin_sport_spi_init_queue(struct bfin_sport_spi_master_data *drv_data)
{
INIT_LIST_HEAD(&drv_data->queue);
spin_lock_init(&drv_data->lock);
drv_data->run = false;
drv_data->busy = 0;
/* init transfer tasklet */
tasklet_init(&drv_data->pump_transfers,
bfin_sport_spi_pump_transfers, (unsigned long)drv_data);
/* init messages workqueue */
INIT_WORK(&drv_data->pump_messages, bfin_sport_spi_pump_messages);
drv_data->workqueue =
create_singlethread_workqueue(dev_name(drv_data->master->dev.parent));
if (drv_data->workqueue == NULL)
return -EBUSY;
return 0;
}
static int
bfin_sport_spi_start_queue(struct bfin_sport_spi_master_data *drv_data)
{
unsigned long flags;
spin_lock_irqsave(&drv_data->lock, flags);
if (drv_data->run || drv_data->busy) {
spin_unlock_irqrestore(&drv_data->lock, flags);
return -EBUSY;
}
drv_data->run = true;
drv_data->cur_msg = NULL;
drv_data->cur_transfer = NULL;
drv_data->cur_chip = NULL;
spin_unlock_irqrestore(&drv_data->lock, flags);
queue_work(drv_data->workqueue, &drv_data->pump_messages);
return 0;
}
static inline int
bfin_sport_spi_stop_queue(struct bfin_sport_spi_master_data *drv_data)
{
unsigned long flags;
unsigned limit = 500;
int status = 0;
spin_lock_irqsave(&drv_data->lock, flags);
/*
* This is a bit lame, but is optimized for the common execution path.
* A wait_queue on the drv_data->busy could be used, but then the common
* execution path (pump_messages) would be required to call wake_up or
* friends on every SPI message. Do this instead
*/
drv_data->run = false;
while (!list_empty(&drv_data->queue) && drv_data->busy && limit--) {
spin_unlock_irqrestore(&drv_data->lock, flags);
msleep(10);
spin_lock_irqsave(&drv_data->lock, flags);
}
if (!list_empty(&drv_data->queue) || drv_data->busy)
status = -EBUSY;
spin_unlock_irqrestore(&drv_data->lock, flags);
return status;
}
static inline int
bfin_sport_spi_destroy_queue(struct bfin_sport_spi_master_data *drv_data)
{
int status;
status = bfin_sport_spi_stop_queue(drv_data);
if (status)
return status;
destroy_workqueue(drv_data->workqueue);
return 0;
}
static int __devinit
bfin_sport_spi_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
struct bfin5xx_spi_master *platform_info;
struct spi_master *master;
struct resource *res, *ires;
struct bfin_sport_spi_master_data *drv_data;
int status;
platform_info = dev->platform_data;
/* Allocate master with space for drv_data */
master = spi_alloc_master(dev, sizeof(*master) + 16);
if (!master) {
dev_err(dev, "cannot alloc spi_master\n");
return -ENOMEM;
}
drv_data = spi_master_get_devdata(master);
drv_data->master = master;
drv_data->dev = dev;
drv_data->pin_req = platform_info->pin_req;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;
master->bus_num = pdev->id;
master->num_chipselect = platform_info->num_chipselect;
master->cleanup = bfin_sport_spi_cleanup;
master->setup = bfin_sport_spi_setup;
master->transfer = bfin_sport_spi_transfer;
/* Find and map our resources */
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (res == NULL) {
dev_err(dev, "cannot get IORESOURCE_MEM\n");
status = -ENOENT;
goto out_error_get_res;
}
drv_data->regs = ioremap(res->start, resource_size(res));
if (drv_data->regs == NULL) {
dev_err(dev, "cannot map registers\n");
status = -ENXIO;
goto out_error_ioremap;
}
ires = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!ires) {
dev_err(dev, "cannot get IORESOURCE_IRQ\n");
status = -ENODEV;
goto out_error_get_ires;
}
drv_data->err_irq = ires->start;
/* Initial and start queue */
status = bfin_sport_spi_init_queue(drv_data);
if (status) {
dev_err(dev, "problem initializing queue\n");
goto out_error_queue_alloc;
}
status = bfin_sport_spi_start_queue(drv_data);
if (status) {
dev_err(dev, "problem starting queue\n");
goto out_error_queue_alloc;
}
status = request_irq(drv_data->err_irq, sport_err_handler,
0, "sport_spi_err", drv_data);
if (status) {
dev_err(dev, "unable to request sport err irq\n");
goto out_error_irq;
}
status = peripheral_request_list(drv_data->pin_req, DRV_NAME);
if (status) {
dev_err(dev, "requesting peripherals failed\n");
goto out_error_peripheral;
}
/* Register with the SPI framework */
platform_set_drvdata(pdev, drv_data);
status = spi_register_master(master);
if (status) {
dev_err(dev, "problem registering spi master\n");
goto out_error_master;
}
dev_info(dev, "%s, regs_base@%p\n", DRV_DESC, drv_data->regs);
return 0;
out_error_master:
peripheral_free_list(drv_data->pin_req);
out_error_peripheral:
free_irq(drv_data->err_irq, drv_data);
out_error_irq:
out_error_queue_alloc:
bfin_sport_spi_destroy_queue(drv_data);
out_error_get_ires:
iounmap(drv_data->regs);
out_error_ioremap:
out_error_get_res:
spi_master_put(master);
return status;
}
/* stop hardware and remove the driver */
static int __devexit
bfin_sport_spi_remove(struct platform_device *pdev)
{
struct bfin_sport_spi_master_data *drv_data = platform_get_drvdata(pdev);
int status = 0;
if (!drv_data)
return 0;
/* Remove the queue */
status = bfin_sport_spi_destroy_queue(drv_data);
if (status)
return status;
/* Disable the SSP at the peripheral and SOC level */
bfin_sport_spi_disable(drv_data);
/* Disconnect from the SPI framework */
spi_unregister_master(drv_data->master);
peripheral_free_list(drv_data->pin_req);
/* Prevent double remove */
platform_set_drvdata(pdev, NULL);
return 0;
}
#ifdef CONFIG_PM
static int
bfin_sport_spi_suspend(struct platform_device *pdev, pm_message_t state)
{
struct bfin_sport_spi_master_data *drv_data = platform_get_drvdata(pdev);
int status;
status = bfin_sport_spi_stop_queue(drv_data);
if (status)
return status;
/* stop hardware */
bfin_sport_spi_disable(drv_data);
return status;
}
static int
bfin_sport_spi_resume(struct platform_device *pdev)
{
struct bfin_sport_spi_master_data *drv_data = platform_get_drvdata(pdev);
int status;
/* Enable the SPI interface */
bfin_sport_spi_enable(drv_data);
/* Start the queue running */
status = bfin_sport_spi_start_queue(drv_data);
if (status)
dev_err(drv_data->dev, "problem resuming queue\n");
return status;
}
#else
# define bfin_sport_spi_suspend NULL
# define bfin_sport_spi_resume NULL
#endif
static struct platform_driver bfin_sport_spi_driver = {
.driver = {
.name = DRV_NAME,
.owner = THIS_MODULE,
},
.probe = bfin_sport_spi_probe,
.remove = __devexit_p(bfin_sport_spi_remove),
.suspend = bfin_sport_spi_suspend,
.resume = bfin_sport_spi_resume,
};
static int __init bfin_sport_spi_init(void)
{
return platform_driver_register(&bfin_sport_spi_driver);
}
module_init(bfin_sport_spi_init);
static void __exit bfin_sport_spi_exit(void)
{
platform_driver_unregister(&bfin_sport_spi_driver);
}
module_exit(bfin_sport_spi_exit);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment