Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm

* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (49 commits)
  [ARM] idle: clean up pm_idle calling, obey hlt_counter
  [ARM] S3C: Fix gpio-config off-by-one bug
  [ARM] S3C64XX: add to_irq() support for EINT() GPIO
  [ARM] S3C64XX: clock.c: fix typo in usb-host clock ctrlbit
  [ARM] S3C64XX: fix HCLK gate defines
  [ARM] Update mach-types
  [ARM] wire up rt_tgsigqueueinfo and perf_counter_open
  OMAP2 clock/powerdomain: off by 1 error in loop timeout comparisons
  OMAP3 SDRC: set FIXEDDELAY when disabling SDRC DLL
  OMAP3: Add support for DPLL3 divisor values higher than 2
  OMAP3 SRAM: convert SRAM code to use macros rather than magic numbers
  OMAP3 SRAM: add more comments on the SRAM code
  OMAP3 clock/SDRC: program SDRC_MR register during SDRC clock change
  OMAP3 clock: add a short delay when lowering CORE clk rate
  OMAP3 clock: initialize SDRC timings at kernel start
  OMAP3 clock: remove wait for DPLL3 M2 clock to stabilize
  [ARM] Add old Feroceon support to compressed/head.S
  [ARM] 5559/1: Limit the stack unwinding caused by a kthread exit
  [ARM] 5558/1: Add extra checks to ARM unwinder to avoid tracing corrupt stacks
  [ARM] 5557/1: Discard some ARM.ex*.*exit.text sections when !HOTPLUG or !HOTPLUG_CPU
  ...

Documentation/kernel-parameters.txt

@@ -1369,6 +1369,27 @@ and is between 256 and 4096 characters. It is defined in the file
 	min_addr=nn[KMG]	[KNL,BOOT,ia64] All physical memory below this
 			physical address is ignored.
 
+	mini2440=	[ARM,HW,KNL]
+			Format:[0..2][b][c][t]
+			Default: "0tb"
+			MINI2440 configuration specification:
+			0 - The attached screen is the 3.5" TFT
+			1 - The attached screen is the 7" TFT
+			2 - The VGA Shield is attached (1024x768)
+			Leaving out the screen size parameter will not load
+			the TFT driver, and the framebuffer will be left
+			unconfigured.
+			b - Enable backlight. The TFT backlight pin will be
+			linked to the kernel VESA blanking code and a GPIO
+			LED. This parameter is not necessary when using the
+			VGA shield.
+			c - Enable the s3c camera interface.
+			t - Reserved for enabling touchscreen support. The
+			touchscreen support is not enabled in the mainstream
+			kernel as of 2.6.30, a preliminary port can be found
+			in the "bleeding edge" mini2440 support kernel at
+			http://repo.or.cz/w/linux-2.6/mini2440.git
+
 	mminit_loglevel=
 			[KNL] When CONFIG_DEBUG_MEMORY_INIT is set, this
 			parameter allows control of the logging verbosity for

MAINTAINERS

@@ -653,6 +653,8 @@ M:	laforge@openezx.org
 L:	openezx-devel@lists.openezx.org (subscribers-only)
 W:	http://www.openezx.org/
 S:	Maintained
+T:	topgit git://git.openezx.org/openezx.git
+F:	arch/arm/mach-pxa/ezx.c
 
 ARM/FARADAY FA526 PORT
 P:	Paulius Zaleckas
@@ -774,11 +776,25 @@ P:	Philipp Zabel
 M:	philipp.zabel@gmail.com
 S:	Maintained
 
+ARM/MIOA701 MACHINE SUPPORT
+P:	Robert Jarzmik
+M:	robert.jarzmik@free.fr
+L:	linux-arm-kernel@lists.arm.linux.org.uk (subscribers-only)
+F:	arch/arm/mach-pxa/mioa701.c
+S:	Maintained
+
 ARM/NEC MOBILEPRO 900/c MACHINE SUPPORT
 P:	Michael Petchkovsky
 M:	mkpetch@internode.on.net
 S:	Maintained
 
+ARM/OPENMOKO NEO FREERUNNER (GTA02) MACHINE SUPPORT
+P:	Nelson Castillo
+M:	arhuaco@freaks-unidos.net
+L:	openmoko-kernel@lists.openmoko.org (subscribers-only)
+W:	http://wiki.openmoko.org/wiki/Neo_FreeRunner
+S:	Supported
+
 ARM/TOSA MACHINE SUPPORT
 P:	Dmitry Eremin-Solenikov
 M:	dbaryshkov@gmail.com
@@ -792,6 +808,12 @@ M:	marek.vasut@gmail.com
 W:	http://hackndev.com
 S:	Maintained
 
+ARM/PALM TREO 680 SUPPORT
+P:	Tomas Cech
+M:	sleep_walker@suse.cz
+W:	http://hackndev.com
+S:	Maintained
+
 ARM/PALMZ72 SUPPORT
 P:	Sergey Lapin
 M:	slapin@ossfans.org

arch/arm/Kconfig

@@ -1241,7 +1241,7 @@ endmenu
 
 menu "CPU Power Management"
 
-if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA)
+if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX)
 
 source "drivers/cpufreq/Kconfig"
 
@@ -1272,6 +1272,10 @@ config CPU_FREQ_PXA
 	default y
 	select CPU_FREQ_DEFAULT_GOV_USERSPACE
 
+config CPU_FREQ_S3C64XX
+	bool "CPUfreq support for Samsung S3C64XX CPUs"
+	depends on CPU_FREQ && CPU_S3C6410
+
 endif
 
 source "drivers/cpuidle/Kconfig"

arch/arm/boot/compressed/head.S

@@ -674,6 +674,15 @@ proc_types:
 		b	__armv4_mmu_cache_off
 		b	__armv5tej_mmu_cache_flush
 
+#ifdef CONFIG_CPU_FEROCEON_OLD_ID
+		/* this conflicts with the standard ARMv5TE entry */
+		.long	0x41009260		@ Old Feroceon
+		.long	0xff00fff0
+		b	__armv4_mmu_cache_on
+		b	__armv4_mmu_cache_off
+		b	__armv5tej_mmu_cache_flush
+#endif
+
 		.word	0x66015261		@ FA526
 		.word	0xff01fff1
 		b	__fa526_cache_on

arch/arm/common/gic.c

@@ -117,7 +117,7 @@ static int gic_set_cpu(unsigned int irq, const struct cpumask *mask_val)
 	u32 val;
 
 	spin_lock(&irq_controller_lock);
-	irq_desc[irq].cpu = cpu;
+	irq_desc[irq].node = cpu;
 	val = readl(reg) & ~(0xff << shift);
 	val |= 1 << (cpu + shift);
 	writel(val, reg);

arch/arm/common/vic.c

@@ -229,14 +229,18 @@ static int vic_set_wake(unsigned int irq, unsigned int on)
 {
 	struct vic_device *v = vic_from_irq(irq);
 	unsigned int off = irq & 31;
+	u32 bit = 1 << off;
 
 	if (!v)
 		return -EINVAL;
 
+	if (!(bit & v->resume_sources))
+		return -EINVAL;
+
 	if (on)
-		v->resume_irqs |= 1 << off;
+		v->resume_irqs |= bit;
 	else
-		v->resume_irqs &= ~(1 << off);
+		v->resume_irqs &= ~bit;
 
 	return 0;
 }

arch/arm/configs/mini2440_defconfig

+#
+# Automatically generated make config: don't edit
+# Linux kernel version: 2.6.30-rc6
+# Wed May 20 12:29:51 2009
+#
+CONFIG_ARM=y
+CONFIG_HAVE_PWM=y
+CONFIG_SYS_SUPPORTS_APM_EMULATION=y
+CONFIG_GENERIC_GPIO=y
+# CONFIG_GENERIC_TIME is not set
+# CONFIG_GENERIC_CLOCKEVENTS is not set
+CONFIG_MMU=y
+CONFIG_NO_IOPORT=y
+CONFIG_GENERIC_HARDIRQS=y
+CONFIG_STACKTRACE_SUPPORT=y
+CONFIG_HAVE_LATENCYTOP_SUPPORT=y
+CONFIG_LOCKDEP_SUPPORT=y
+CONFIG_TRACE_IRQFLAGS_SUPPORT=y
+CONFIG_HARDIRQS_SW_RESEND=y
+CONFIG_GENERIC_IRQ_PROBE=y
+CONFIG_RWSEM_GENERIC_SPINLOCK=y
+# CONFIG_ARCH_HAS_ILOG2_U32 is not set
+# CONFIG_ARCH_HAS_ILOG2_U64 is not set
+CONFIG_GENERIC_HWEIGHT=y
+CONFIG_GENERIC_CALIBRATE_DELAY=y
+CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y
+CONFIG_VECTORS_BASE=0xffff0000
+CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config"
+
+#
+# General setup
+#
+CONFIG_EXPERIMENTAL=y
+CONFIG_BROKEN_ON_SMP=y
+CONFIG_INIT_ENV_ARG_LIMIT=32
+CONFIG_LOCALVERSION=""
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SWAP=y
+CONFIG_SYSVIPC=y
+CONFIG_SYSVIPC_SYSCTL=y
+CONFIG_POSIX_MQUEUE=y
+CONFIG_POSIX_MQUEUE_SYSCTL=y
+# CONFIG_BSD_PROCESS_ACCT is not set
+# CONFIG_TASKSTATS is not set
+# CONFIG_AUDIT is not set
+
+#
+# RCU Subsystem
+#
+CONFIG_CLASSIC_RCU=y
+# CONFIG_TREE_RCU is not set
+# CONFIG_PREEMPT_RCU is not set
+# CONFIG_TREE_RCU_TRACE is not set
+# CONFIG_PREEMPT_RCU_TRACE is not set
+# CONFIG_IKCONFIG is not set
+CONFIG_LOG_BUF_SHIFT=17
+# CONFIG_GROUP_SCHED is not set
+# CONFIG_CGROUPS is not set
+# CONFIG_SYSFS_DEPRECATED_V2 is not set
+CONFIG_RELAY=y
+CONFIG_NAMESPACES=y
+CONFIG_UTS_NS=y
+CONFIG_IPC_NS=y
+# CONFIG_USER_NS is not set
+# CONFIG_PID_NS is not set
+# CONFIG_NET_NS is not set
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_INITRAMFS_SOURCE=""
+CONFIG_RD_GZIP=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_SYSCTL=y
+CONFIG_ANON_INODES=y
+# CONFIG_EMBEDDED is not set
+CONFIG_UID16=y
+CONFIG_SYSCTL_SYSCALL=y
+CONFIG_KALLSYMS=y
+# CONFIG_KALLSYMS_ALL is not set
+# CONFIG_KALLSYMS_EXTRA_PASS is not set
+CONFIG_STRIP_ASM_SYMS=y
+CONFIG_HOTPLUG=y
+CONFIG_PRINTK=y
+CONFIG_BUG=y
+CONFIG_ELF_CORE=y
+CONFIG_BASE_FULL=y
+CONFIG_FUTEX=y
+CONFIG_EPOLL=y
+CONFIG_SIGNALFD=y
+CONFIG_TIMERFD=y
+CONFIG_EVENTFD=y
+CONFIG_SHMEM=y
+CONFIG_AIO=y
+CONFIG_VM_EVENT_COUNTERS=y
+CONFIG_SLUB_DEBUG=y
+# CONFIG_COMPAT_BRK is not set
+# CONFIG_SLAB is not set
+CONFIG_SLUB=y
+# CONFIG_SLOB is not set
+# CONFIG_PROFILING is not set
+# CONFIG_MARKERS is not set
+CONFIG_HAVE_OPROFILE=y
+# CONFIG_KPROBES is not set
+CONFIG_HAVE_KPROBES=y
+CONFIG_HAVE_KRETPROBES=y
+CONFIG_HAVE_CLK=y
+# CONFIG_SLOW_WORK is not set
+CONFIG_HAVE_GENERIC_DMA_COHERENT=y
+CONFIG_SLABINFO=y
+CONFIG_RT_MUTEXES=y
+CONFIG_BASE_SMALL=0
+CONFIG_MODULES=y
+CONFIG_MODULE_FORCE_LOAD=y
+CONFIG_MODULE_UNLOAD=y
+CONFIG_MODULE_FORCE_UNLOAD=y
+# CONFIG_MODVERSIONS is not set
+# CONFIG_MODULE_SRCVERSION_ALL is not set
+CONFIG_BLOCK=y
+CONFIG_LBD=y
+# CONFIG_BLK_DEV_BSG is not set
+CONFIG_BLK_DEV_INTEGRITY=y
+
+#
+# IO Schedulers
+#
+CONFIG_IOSCHED_NOOP=y
+CONFIG_IOSCHED_AS=y
+CONFIG_IOSCHED_DEADLINE=y
+CONFIG_IOSCHED_CFQ=y
+CONFIG_DEFAULT_AS=y
+# CONFIG_DEFAULT_DEADLINE is not set
+# CONFIG_DEFAULT_CFQ is not set
+# CONFIG_DEFAULT_NOOP is not set
+CONFIG_DEFAULT_IOSCHED="anticipatory"
+CONFIG_FREEZER=y
+
+#
+# System Type
+#
+# CONFIG_ARCH_AAEC2000 is not set
+# CONFIG_ARCH_INTEGRATOR is not set
+# CONFIG_ARCH_REALVIEW is not set
+# CONFIG_ARCH_VERSATILE is not set
+# CONFIG_ARCH_AT91 is not set
+# CONFIG_ARCH_CLPS711X is not set
+# CONFIG_ARCH_EBSA110 is not set
+# CONFIG_ARCH_EP93XX is not set
+# CONFIG_ARCH_GEMINI is not set
+# CONFIG_ARCH_FOOTBRIDGE is not set
+# CONFIG_ARCH_NETX is not set
+# CONFIG_ARCH_H720X is not set
+# CONFIG_ARCH_IMX is not set
+# CONFIG_ARCH_IOP13XX is not set
+# CONFIG_ARCH_IOP32X is not set
+# CONFIG_ARCH_IOP33X is not set
+# CONFIG_ARCH_IXP23XX is not set
+# CONFIG_ARCH_IXP2000 is not set
+# CONFIG_ARCH_IXP4XX is not set
+# CONFIG_ARCH_L7200 is not set
+# CONFIG_ARCH_KIRKWOOD is not set
+# CONFIG_ARCH_KS8695 is not set
+# CONFIG_ARCH_NS9XXX is not set
+# CONFIG_ARCH_LOKI is not set
+# CONFIG_ARCH_MV78XX0 is not set
+# CONFIG_ARCH_MXC is not set
+# CONFIG_ARCH_ORION5X is not set
+# CONFIG_ARCH_PNX4008 is not set
+# CONFIG_ARCH_PXA is not set
+# CONFIG_ARCH_MMP is not set
+# CONFIG_ARCH_RPC is not set
+# CONFIG_ARCH_SA1100 is not set
+CONFIG_ARCH_S3C2410=y
+# CONFIG_ARCH_S3C64XX is not set
+# CONFIG_ARCH_SHARK is not set
+# CONFIG_ARCH_LH7A40X is not set
+# CONFIG_ARCH_DAVINCI is not set
+# CONFIG_ARCH_OMAP is not set
+# CONFIG_ARCH_MSM is not set
+# CONFIG_ARCH_W90X900 is not set
+CONFIG_PLAT_S3C24XX=y
+CONFIG_S3C2410_CLOCK=y
+CONFIG_CPU_S3C244X=y
+CONFIG_S3C24XX_PWM=y
+CONFIG_S3C24XX_GPIO_EXTRA=0
+CONFIG_S3C2410_DMA=y
+# CONFIG_S3C2410_DMA_DEBUG is not set
+CONFIG_S3C24XX_ADC=y
+CONFIG_PLAT_S3C=y
+CONFIG_CPU_LLSERIAL_S3C2440_ONLY=y
+CONFIG_CPU_LLSERIAL_S3C2440=y
+
+#
+# Boot options
+#
+# CONFIG_S3C_BOOT_WATCHDOG is not set
+# CONFIG_S3C_BOOT_ERROR_RESET is not set
+CONFIG_S3C_BOOT_UART_FORCE_FIFO=y
+
+#
+# Power management
+#
+# CONFIG_S3C2410_PM_DEBUG is not set
+# CONFIG_S3C2410_PM_CHECK is not set
+CONFIG_S3C_LOWLEVEL_UART_PORT=0
+CONFIG_S3C_GPIO_SPACE=0
+
+#
+# S3C2400 Machines
+#
+CONFIG_S3C2410_PM=y
+CONFIG_S3C2410_GPIO=y
+
+#
+# S3C2410 Machines
+#
+# CONFIG_ARCH_SMDK2410 is not set
+# CONFIG_ARCH_H1940 is not set
+# CONFIG_MACH_N30 is not set
+# CONFIG_ARCH_BAST is not set
+# CONFIG_MACH_OTOM is not set
+# CONFIG_MACH_AML_M5900 is not set
+# CONFIG_MACH_TCT_HAMMER is not set
+# CONFIG_MACH_VR1000 is not set
+# CONFIG_MACH_QT2410 is not set
+
+#
+# S3C2412 Machines
+#
+# CONFIG_MACH_JIVE is not set
+# CONFIG_MACH_SMDK2413 is not set
+# CONFIG_MACH_SMDK2412 is not set
+# CONFIG_MACH_VSTMS is not set
+CONFIG_CPU_S3C2440=y
+CONFIG_S3C2440_DMA=y
+
+#
+# S3C2440 Machines
+#
+# CONFIG_MACH_ANUBIS is not set
+# CONFIG_MACH_OSIRIS is not set
+# CONFIG_MACH_RX3715 is not set
+# CONFIG_ARCH_S3C2440 is not set
+# CONFIG_MACH_NEXCODER_2440 is not set
+# CONFIG_MACH_AT2440EVB is not set
+CONFIG_MACH_MINI2440=y
+
+#
+# S3C2442 Machines
+#
+
+#
+# S3C2443 Machines
+#
+# CONFIG_MACH_SMDK2443 is not set
+
+#
+# Processor Type
+#
+CONFIG_CPU_32=y
+CONFIG_CPU_ARM920T=y
+CONFIG_CPU_32v4T=y
+CONFIG_CPU_ABRT_EV4T=y
+CONFIG_CPU_PABRT_NOIFAR=y
+CONFIG_CPU_CACHE_V4WT=y
+CONFIG_CPU_CACHE_VIVT=y
+CONFIG_CPU_COPY_V4WB=y
+CONFIG_CPU_TLB_V4WBI=y
+CONFIG_CPU_CP15=y
+CONFIG_CPU_CP15_MMU=y
+
+#
+# Processor Features
+#
+CONFIG_ARM_THUMB=y
+# CONFIG_CPU_ICACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_DISABLE is not set
+# CONFIG_CPU_DCACHE_WRITETHROUGH is not set
+# CONFIG_OUTER_CACHE is not set
+
+#
+# Bus support
+#
+# CONFIG_PCI_SYSCALL is not set
+# CONFIG_ARCH_SUPPORTS_MSI is not set
+# CONFIG_PCCARD is not set
+
+#
+# Kernel Features
+#
+CONFIG_VMSPLIT_3G=y
+# CONFIG_VMSPLIT_2G is not set
+# CONFIG_VMSPLIT_1G is not set
+CONFIG_PAGE_OFFSET=0xC0000000
+# CONFIG_PREEMPT is not set
+CONFIG_HZ=200
+CONFIG_AEABI=y
+# CONFIG_OABI_COMPAT is not set
+CONFIG_ARCH_FLATMEM_HAS_HOLES=y
+# CONFIG_ARCH_SPARSEMEM_DEFAULT is not set
+# CONFIG_ARCH_SELECT_MEMORY_MODEL is not set
+# CONFIG_HIGHMEM is not set
+CONFIG_SELECT_MEMORY_MODEL=y
+CONFIG_FLATMEM_MANUAL=y
+# CONFIG_DISCONTIGMEM_MANUAL is not set
+# CONFIG_SPARSEMEM_MANUAL is not set
+CONFIG_FLATMEM=y
+CONFIG_FLAT_NODE_MEM_MAP=y
+CONFIG_PAGEFLAGS_EXTENDED=y
+CONFIG_SPLIT_PTLOCK_CPUS=4096
+# CONFIG_PHYS_ADDR_T_64BIT is not set
+CONFIG_ZONE_DMA_FLAG=0
+CONFIG_VIRT_TO_BUS=y
+CONFIG_UNEVICTABLE_LRU=y
+CONFIG_HAVE_MLOCK=y
+CONFIG_HAVE_MLOCKED_PAGE_BIT=y
+CONFIG_ALIGNMENT_TRAP=y
+
+#
+# Boot options
+#
+CONFIG_ZBOOT_ROM_TEXT=0
+CONFIG_ZBOOT_ROM_BSS=0
+CONFIG_CMDLINE=""
+# CONFIG_XIP_KERNEL is not set
+CONFIG_KEXEC=y
+CONFIG_ATAGS_PROC=y
+
+#
+# CPU Power Management
+#
+CONFIG_CPU_IDLE=y
+CONFIG_CPU_IDLE_GOV_LADDER=y
+
+#
+# Floating point emulation
+#
+
+#
+# At least one emulation must be selected
+#
+
+#
+# Userspace binary formats
+#
+CONFIG_BINFMT_ELF=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+CONFIG_HAVE_AOUT=y
+CONFIG_BINFMT_AOUT=m
+CONFIG_BINFMT_MISC=m
+
+#
+# Power management options
+#
+CONFIG_PM=y
+# CONFIG_PM_DEBUG is not set
+CONFIG_PM_SLEEP=y
+CONFIG_SUSPEND=y
+CONFIG_SUSPEND_FREEZER=y
+CONFIG_APM_EMULATION=y
+CONFIG_ARCH_SUSPEND_POSSIBLE=y
+CONFIG_NET=y
+
+#
+# Networking options
+#
+CONFIG_PACKET=y
+CONFIG_PACKET_MMAP=y
+CONFIG_UNIX=y
+CONFIG_XFRM=y
+CONFIG_XFRM_USER=m
+# CONFIG_XFRM_SUB_POLICY is not set
+# CONFIG_XFRM_MIGRATE is not set
+# CONFIG_XFRM_STATISTICS is not set
+CONFIG_NET_KEY=m
+# CONFIG_NET_KEY_MIGRATE is not set
+CONFIG_INET=y
+CONFIG_IP_MULTICAST=y
+CONFIG_IP_ADVANCED_ROUTER=y
+CONFIG_ASK_IP_FIB_HASH=y
+# CONFIG_IP_FIB_TRIE is not set
+CONFIG_IP_FIB_HASH=y
+CONFIG_IP_MULTIPLE_TABLES=y
+CONFIG_IP_ROUTE_MULTIPATH=y
+CONFIG_IP_ROUTE_VERBOSE=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_IP_PNP_RARP=y
+# CONFIG_NET_IPIP is not set
+# CONFIG_NET_IPGRE is not set
+CONFIG_IP_MROUTE=y
+CONFIG_IP_PIMSM_V1=y
+CONFIG_IP_PIMSM_V2=y
+# CONFIG_ARPD is not set
+CONFIG_SYN_COOKIES=y
+# CONFIG_INET_AH is not set
+# CONFIG_INET_ESP is not set
+# CONFIG_INET_IPCOMP is not set
+# CONFIG_INET_XFRM_TUNNEL is not set
+# CONFIG_INET_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_TRANSPORT is not set
+# CONFIG_INET_XFRM_MODE_TUNNEL is not set
+# CONFIG_INET_XFRM_MODE_BEET is not set
+# CONFIG_INET_LRO is not set
+CONFIG_INET_DIAG=m
+CONFIG_INET_TCP_DIAG=m
+# CONFIG_TCP_CONG_ADVANCED is not set
+CONFIG_TCP_CONG_CUBIC=y
+CONFIG_DEFAULT_TCP_CONG="cubic"
+# CONFIG_TCP_MD5SIG is not set
+# CONFIG_IPV6 is not set
+# CONFIG_NETWORK_SECMARK is not set
+CONFIG_NETFILTER=y
+# CONFIG_NETFILTER_DEBUG is not set
+CONFIG_NETFILTER_ADVANCED=y
+CONFIG_BRIDGE_NETFILTER=y
+
+#
+# Core Netfilter Configuration
+#
+# CONFIG_NETFILTER_NETLINK_QUEUE is not set
+# CONFIG_NETFILTER_NETLINK_LOG is not set
+# CONFIG_NF_CONNTRACK is not set
+# CONFIG_NETFILTER_XTABLES is not set
+# CONFIG_IP_VS is not set
+
+#
+# IP: Netfilter Configuration
+#
+# CONFIG_NF_DEFRAG_IPV4 is not set
+# CONFIG_IP_NF_QUEUE is not set
+# CONFIG_IP_NF_IPTABLES is not set
+# CONFIG_IP_NF_ARPTABLES is not set
+# CONFIG_BRIDGE_NF_EBTABLES is not set
+# CONFIG_IP_DCCP is not set
+# CONFIG_IP_SCTP is not set
+# CONFIG_TIPC is not set
+# CONFIG_ATM is not set
+CONFIG_STP=m
+CONFIG_GARP=m
+CONFIG_BRIDGE=m
+# CONFIG_NET_DSA is not set
+CONFIG_VLAN_8021Q=m
+CONFIG_VLAN_8021Q_GVRP=y
+# CONFIG_DECNET is not set
+CONFIG_LLC=m
+# CONFIG_LLC2 is not set
+# CONFIG_IPX is not set
+# CONFIG_ATALK is not set
+# CONFIG_X25 is not set
+# CONFIG_LAPB is not set
+# CONFIG_ECONET is not set
+# CONFIG_WAN_ROUTER is not set
+# CONFIG_PHONET is not set
+# CONFIG_NET_SCHED is not set
+# CONFIG_DCB is not set
+
+#
+# Network testing
+#
+CONFIG_NET_PKTGEN=m
+# CONFIG_HAMRADIO is not set
+# CONFIG_CAN is not set
+# CONFIG_IRDA is not set
+CONFIG_BT=m
+CONFIG_BT_L2CAP=m
+CONFIG_BT_SCO=m
+CONFIG_BT_RFCOMM=m
+CONFIG_BT_RFCOMM_TTY=y
+CONFIG_BT_BNEP=m
+CONFIG_BT_BNEP_MC_FILTER=y
+CONFIG_BT_BNEP_PROTO_FILTER=y
+CONFIG_BT_HIDP=m
+
+#
+# Bluetooth device drivers
+#
+CONFIG_BT_HCIBTUSB=m
+CONFIG_BT_HCIBTSDIO=m
+CONFIG_BT_HCIUART=m
+CONFIG_BT_HCIUART_H4=y
+CONFIG_BT_HCIUART_BCSP=y
+CONFIG_BT_HCIUART_LL=y
+CONFIG_BT_HCIBCM203X=m
+CONFIG_BT_HCIBPA10X=m
+CONFIG_BT_HCIBFUSB=m
+CONFIG_BT_HCIVHCI=m
+# CONFIG_AF_RXRPC is not set
+CONFIG_FIB_RULES=y
+CONFIG_WIRELESS=y
+CONFIG_CFG80211=m
+CONFIG_CFG80211_REG_DEBUG=y
+CONFIG_WIRELESS_OLD_REGULATORY=y
+CONFIG_WIRELESS_EXT=y
+CONFIG_WIRELESS_EXT_SYSFS=y
+CONFIG_LIB80211=m
+CONFIG_LIB80211_CRYPT_WEP=m
+CONFIG_LIB80211_CRYPT_CCMP=m
+CONFIG_LIB80211_CRYPT_TKIP=m
+# CONFIG_LIB80211_DEBUG is not set
+CONFIG_MAC80211=m
+
+#
+# Rate control algorithm selection
+#
+CONFIG_MAC80211_RC_MINSTREL=y
+# CONFIG_MAC80211_RC_DEFAULT_PID is not set
+CONFIG_MAC80211_RC_DEFAULT_MINSTREL=y
+CONFIG_MAC80211_RC_DEFAULT="minstrel"
+CONFIG_MAC80211_MESH=y
+CONFIG_MAC80211_LEDS=y
+# CONFIG_MAC80211_DEBUGFS is not set
+# CONFIG_MAC80211_DEBUG_MENU is not set
+# CONFIG_WIMAX is not set
+# CONFIG_RFKILL is not set
+# CONFIG_NET_9P is not set
+
+#
+# Device Drivers
+#
+
+#
+# Generic Driver Options
+#
+CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
+CONFIG_STANDALONE=y
+CONFIG_PREVENT_FIRMWARE_BUILD=y
+CONFIG_FW_LOADER=y
+# CONFIG_FIRMWARE_IN_KERNEL is not set
+CONFIG_EXTRA_FIRMWARE=""
+# CONFIG_DEBUG_DRIVER is not set
+# CONFIG_DEBUG_DEVRES is not set
+# CONFIG_SYS_HYPERVISOR is not set
+CONFIG_CONNECTOR=m
+CONFIG_MTD=y
+# CONFIG_MTD_DEBUG is not set
+CONFIG_MTD_CONCAT=y
+CONFIG_MTD_PARTITIONS=y
+# CONFIG_MTD_TESTS is not set
+# CONFIG_MTD_REDBOOT_PARTS is not set
+CONFIG_MTD_CMDLINE_PARTS=y
+# CONFIG_MTD_AFS_PARTS is not set
+# CONFIG_MTD_AR7_PARTS is not set
+
+#
+# User Modules And Translation Layers
+#
+CONFIG_MTD_CHAR=y
+CONFIG_MTD_BLKDEVS=y
+CONFIG_MTD_BLOCK=y
+CONFIG_FTL=y
+CONFIG_NFTL=y
+CONFIG_NFTL_RW=y
+CONFIG_INFTL=y
+CONFIG_RFD_FTL=y
+# CONFIG_SSFDC is not set
+# CONFIG_MTD_OOPS is not set
+
+#
+# RAM/ROM/Flash chip drivers
+#
+CONFIG_MTD_CFI=y
+CONFIG_MTD_JEDECPROBE=y
+CONFIG_MTD_GEN_PROBE=y
+# CONFIG_MTD_CFI_ADV_OPTIONS is not set
+CONFIG_MTD_MAP_BANK_WIDTH_1=y
+CONFIG_MTD_MAP_BANK_WIDTH_2=y
+CONFIG_MTD_MAP_BANK_WIDTH_4=y
+# CONFIG_MTD_MAP_BANK_WIDTH_8 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_16 is not set
+# CONFIG_MTD_MAP_BANK_WIDTH_32 is not set
+CONFIG_MTD_CFI_I1=y
+CONFIG_MTD_CFI_I2=y
+# CONFIG_MTD_CFI_I4 is not set
+# CONFIG_MTD_CFI_I8 is not set
+# CONFIG_MTD_CFI_INTELEXT is not set
+CONFIG_MTD_CFI_AMDSTD=y
+CONFIG_MTD_CFI_STAA=y
+CONFIG_MTD_CFI_UTIL=y
+CONFIG_MTD_RAM=y
+CONFIG_MTD_ROM=y
+# CONFIG_MTD_ABSENT is not set
+
+#
+# Mapping drivers for chip access
+#
+# CONFIG_MTD_COMPLEX_MAPPINGS is not set
+# CONFIG_MTD_PHYSMAP is not set
+# CONFIG_MTD_ARM_INTEGRATOR is not set
+# CONFIG_MTD_IMPA7 is not set
+# CONFIG_MTD_PLATRAM is not set
+
+#
+# Self-contained MTD device drivers
+#
+# CONFIG_MTD_DATAFLASH is not set
+# CONFIG_MTD_M25P80 is not set
+# CONFIG_MTD_SLRAM is not set
+# CONFIG_MTD_PHRAM is not set
+# CONFIG_MTD_MTDRAM is not set
+# CONFIG_MTD_BLOCK2MTD is not set
+
+#
+# Disk-On-Chip Device Drivers
+#
+# CONFIG_MTD_DOC2000 is not set
+# CONFIG_MTD_DOC2001 is not set
+# CONFIG_MTD_DOC2001PLUS is not set
+CONFIG_MTD_NAND=y
+CONFIG_MTD_NAND_VERIFY_WRITE=y
+# CONFIG_MTD_NAND_ECC_SMC is not set
+# CONFIG_MTD_NAND_MUSEUM_IDS is not set
+# CONFIG_MTD_NAND_GPIO is not set
+CONFIG_MTD_NAND_IDS=y
+CONFIG_MTD_NAND_S3C2410=y
+# CONFIG_MTD_NAND_S3C2410_DEBUG is not set
+# CONFIG_MTD_NAND_S3C2410_HWECC is not set
+# CONFIG_MTD_NAND_S3C2410_CLKSTOP is not set
+# CONFIG_MTD_NAND_DISKONCHIP is not set
+# CONFIG_MTD_NAND_NANDSIM is not set
+CONFIG_MTD_NAND_PLATFORM=y
+# CONFIG_MTD_ALAUDA is not set
+# CONFIG_MTD_ONENAND is not set
+
+#
+# LPDDR flash memory drivers
+#
+CONFIG_MTD_LPDDR=y
+CONFIG_MTD_QINFO_PROBE=y
+
+#
+# UBI - Unsorted block images
+#
+# CONFIG_MTD_UBI is not set
+# CONFIG_PARPORT is not set
+CONFIG_BLK_DEV=y
+# CONFIG_BLK_DEV_COW_COMMON is not set
+CONFIG_BLK_DEV_LOOP=m
+# CONFIG_BLK_DEV_CRYPTOLOOP is not set
+CONFIG_BLK_DEV_NBD=m
+# CONFIG_BLK_DEV_UB is not set
+CONFIG_BLK_DEV_RAM=y
+CONFIG_BLK_DEV_RAM_COUNT=16
+CONFIG_BLK_DEV_RAM_SIZE=65536
+# CONFIG_BLK_DEV_XIP is not set
+CONFIG_CDROM_PKTCDVD=m
+CONFIG_CDROM_PKTCDVD_BUFFERS=8
+# CONFIG_CDROM_PKTCDVD_WCACHE is not set
+# CONFIG_ATA_OVER_ETH is not set
+CONFIG_MISC_DEVICES=y
+# CONFIG_ICS932S401 is not set
+# CONFIG_ENCLOSURE_SERVICES is not set
+# CONFIG_ISL29003 is not set
+# CONFIG_C2PORT is not set
+
+#
+# EEPROM support
+#
+CONFIG_EEPROM_AT24=y
+# CONFIG_EEPROM_AT25 is not set
+# CONFIG_EEPROM_LEGACY is not set
+# CONFIG_EEPROM_93CX6 is not set
+CONFIG_HAVE_IDE=y
+# CONFIG_IDE is not set
+
+#
+# SCSI device support
+#
+# CONFIG_RAID_ATTRS is not set
+CONFIG_SCSI=m
+CONFIG_SCSI_DMA=y
+# CONFIG_SCSI_TGT is not set
+# CONFIG_SCSI_NETLINK is not set
+# CONFIG_SCSI_PROC_FS is not set
+
+#
+# SCSI support type (disk, tape, CD-ROM)
+#
+CONFIG_BLK_DEV_SD=m
+# CONFIG_CHR_DEV_ST is not set
+# CONFIG_CHR_DEV_OSST is not set
+# CONFIG_BLK_DEV_SR is not set
+CONFIG_CHR_DEV_SG=m
+# CONFIG_CHR_DEV_SCH is not set
+
+#
+# Some SCSI devices (e.g. CD jukebox) support multiple LUNs
+#
+# CONFIG_SCSI_MULTI_LUN is not set
+# CONFIG_SCSI_CONSTANTS is not set
+# CONFIG_SCSI_LOGGING is not set
+# CONFIG_SCSI_SCAN_ASYNC is not set
+CONFIG_SCSI_WAIT_SCAN=m
+
+#
+# SCSI Transports
+#
+# CONFIG_SCSI_SPI_ATTRS is not set
+# CONFIG_SCSI_FC_ATTRS is not set
+# CONFIG_SCSI_ISCSI_ATTRS is not set
+# CONFIG_SCSI_SAS_LIBSAS is not set
+# CONFIG_SCSI_SRP_ATTRS is not set
+# CONFIG_SCSI_LOWLEVEL is not set
+# CONFIG_SCSI_DH is not set
+# CONFIG_SCSI_OSD_INITIATOR is not set
+# CONFIG_ATA is not set
+# CONFIG_MD is not set
+CONFIG_NETDEVICES=y
+CONFIG_COMPAT_NET_DEV_OPS=y
+# CONFIG_DUMMY is not set
+# CONFIG_BONDING is not set
+# CONFIG_MACVLAN is not set
+# CONFIG_EQUALIZER is not set
+CONFIG_TUN=m
+# CONFIG_VETH is not set
+# CONFIG_PHYLIB is not set
+CONFIG_NET_ETHERNET=y
+CONFIG_MII=y
+# CONFIG_AX88796 is not set
+# CONFIG_SMC91X is not set
+CONFIG_DM9000=y
+CONFIG_DM9000_DEBUGLEVEL=4
+# CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL is not set
+# CONFIG_ENC28J60 is not set
+# CONFIG_ETHOC is not set
+# CONFIG_SMC911X is not set
+# CONFIG_SMSC911X is not set
+# CONFIG_DNET is not set
+# CONFIG_IBM_NEW_EMAC_ZMII is not set
+# CONFIG_IBM_NEW_EMAC_RGMII is not set
+# CONFIG_IBM_NEW_EMAC_TAH is not set
+# CONFIG_IBM_NEW_EMAC_EMAC4 is not set
+# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set
+# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set
+# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set
+# CONFIG_B44 is not set
+# CONFIG_NETDEV_1000 is not set
+# CONFIG_NETDEV_10000 is not set
+
+#
+# Wireless LAN
+#
+# CONFIG_WLAN_PRE80211 is not set
+CONFIG_WLAN_80211=y
+CONFIG_LIBERTAS=m
+# CONFIG_LIBERTAS_USB is not set
+CONFIG_LIBERTAS_SDIO=m
+# CONFIG_LIBERTAS_SPI is not set
+# CONFIG_LIBERTAS_DEBUG is not set
+# CONFIG_LIBERTAS_THINFIRM is not set
+# CONFIG_AT76C50X_USB is not set
+# CONFIG_USB_ZD1201 is not set
+# CONFIG_USB_NET_RNDIS_WLAN is not set
+# CONFIG_RTL8187 is not set
+# CONFIG_MAC80211_HWSIM is not set
+# CONFIG_P54_COMMON is not set
+# CONFIG_AR9170_USB is not set
+CONFIG_HOSTAP=m
+CONFIG_HOSTAP_FIRMWARE=y
+CONFIG_HOSTAP_FIRMWARE_NVRAM=y
+# CONFIG_B43 is not set
+# CONFIG_B43LEGACY is not set
+CONFIG_ZD1211RW=m
+CONFIG_ZD1211RW_DEBUG=y
+# CONFIG_RT2X00 is not set
+
+#
+# Enable WiMAX (Networking options) to see the WiMAX drivers
+#
+
+#
+# USB Network Adapters
+#
+# CONFIG_USB_CATC is not set
+# CONFIG_USB_KAWETH is not set
+# CONFIG_USB_PEGASUS is not set
+# CONFIG_USB_RTL8150 is not set
+# CONFIG_USB_USBNET is not set
+# CONFIG_WAN is not set
+CONFIG_PPP=m
+CONFIG_PPP_MULTILINK=y
+CONFIG_PPP_FILTER=y
+CONFIG_PPP_ASYNC=m
+CONFIG_PPP_SYNC_TTY=m
+CONFIG_PPP_DEFLATE=m
+CONFIG_PPP_BSDCOMP=m
+CONFIG_PPP_MPPE=m
+# CONFIG_PPPOE is not set
+# CONFIG_PPPOL2TP is not set
+# CONFIG_SLIP is not set
+CONFIG_SLHC=m
+# CONFIG_NETCONSOLE is not set
+# CONFIG_NETPOLL is not set
+# CONFIG_NET_POLL_CONTROLLER is not set
+# CONFIG_ISDN is not set
+
+#
+# Input device support
+#
+CONFIG_INPUT=y
+CONFIG_INPUT_FF_MEMLESS=y
+# CONFIG_INPUT_POLLDEV is not set
+
+#
+# Userland interfaces
+#
+CONFIG_INPUT_MOUSEDEV=y
+CONFIG_INPUT_MOUSEDEV_PSAUX=y
+CONFIG_INPUT_MOUSEDEV_SCREEN_X=1024
+CONFIG_INPUT_MOUSEDEV_SCREEN_Y=768
+# CONFIG_INPUT_JOYDEV is not set
+CONFIG_INPUT_EVDEV=y
+CONFIG_INPUT_EVBUG=m
+
+#
+# Input Device Drivers
+#
+CONFIG_INPUT_KEYBOARD=y
+# CONFIG_KEYBOARD_ATKBD is not set
+# CONFIG_KEYBOARD_SUNKBD is not set
+# CONFIG_KEYBOARD_LKKBD is not set
+# CONFIG_KEYBOARD_XTKBD is not set
+# CONFIG_KEYBOARD_NEWTON is not set
+# CONFIG_KEYBOARD_STOWAWAY is not set
+CONFIG_KEYBOARD_GPIO=y
+CONFIG_INPUT_MOUSE=y
+CONFIG_MOUSE_PS2=y
+CONFIG_MOUSE_PS2_ALPS=y
+CONFIG_MOUSE_PS2_LOGIPS2PP=y
+CONFIG_MOUSE_PS2_SYNAPTICS=y
+CONFIG_MOUSE_PS2_TRACKPOINT=y
+# CONFIG_MOUSE_PS2_ELANTECH is not set
+# CONFIG_MOUSE_PS2_TOUCHKIT is not set
+# CONFIG_MOUSE_SERIAL is not set
+# CONFIG_MOUSE_APPLETOUCH is not set
+# CONFIG_MOUSE_BCM5974 is not set
+# CONFIG_MOUSE_VSXXXAA is not set
+# CONFIG_MOUSE_GPIO is not set
+# CONFIG_INPUT_JOYSTICK is not set
+# CONFIG_INPUT_TABLET is not set
+CONFIG_INPUT_TOUCHSCREEN=y
+# CONFIG_TOUCHSCREEN_ADS7846 is not set
+# CONFIG_TOUCHSCREEN_AD7877 is not set
+# CONFIG_TOUCHSCREEN_AD7879_I2C is not set
+# CONFIG_TOUCHSCREEN_AD7879_SPI is not set
+# CONFIG_TOUCHSCREEN_AD7879 is not set
+# CONFIG_TOUCHSCREEN_FUJITSU is not set
+# CONFIG_TOUCHSCREEN_GUNZE is not set
+# CONFIG_TOUCHSCREEN_ELO is not set
+# CONFIG_TOUCHSCREEN_WACOM_W8001 is not set
+# CONFIG_TOUCHSCREEN_MTOUCH is not set
+# CONFIG_TOUCHSCREEN_INEXIO is not set
+# CONFIG_TOUCHSCREEN_MK712 is not set
+# CONFIG_TOUCHSCREEN_PENMOUNT is not set
+# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set
+# CONFIG_TOUCHSCREEN_TOUCHWIN is not set
+# CONFIG_TOUCHSCREEN_USB_COMPOSITE is not set
+# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set
+# CONFIG_TOUCHSCREEN_TSC2007 is not set
+# CONFIG_INPUT_MISC is not set
+
+#
+# Hardware I/O ports
+#
+CONFIG_SERIO=y
+CONFIG_SERIO_SERPORT=y
+CONFIG_SERIO_LIBPS2=y
+CONFIG_SERIO_RAW=y
+# CONFIG_GAMEPORT is not set
+
+#
+# Character devices
+#
+CONFIG_VT=y
+CONFIG_CONSOLE_TRANSLATIONS=y
+CONFIG_VT_CONSOLE=y
+CONFIG_HW_CONSOLE=y
+CONFIG_VT_HW_CONSOLE_BINDING=y
+CONFIG_DEVKMEM=y
+# CONFIG_SERIAL_NONSTANDARD is not set
+
+#
+# Serial drivers
+#
+# CONFIG_SERIAL_8250 is not set
+
+#
+# Non-8250 serial port support
+#
+CONFIG_SERIAL_SAMSUNG=y
+CONFIG_SERIAL_SAMSUNG_UARTS=3
+CONFIG_SERIAL_SAMSUNG_CONSOLE=y
+CONFIG_SERIAL_S3C2440=y
+# CONFIG_SERIAL_MAX3100 is not set
+CONFIG_SERIAL_CORE=y
+CONFIG_SERIAL_CORE_CONSOLE=y
+CONFIG_UNIX98_PTYS=y
+# CONFIG_DEVPTS_MULTIPLE_INSTANCES is not set
+CONFIG_LEGACY_PTYS=y
+CONFIG_LEGACY_PTY_COUNT=128
+CONFIG_IPMI_HANDLER=m
+# CONFIG_IPMI_PANIC_EVENT is not set
+CONFIG_IPMI_DEVICE_INTERFACE=m
+CONFIG_IPMI_SI=m
+CONFIG_IPMI_WATCHDOG=m
+CONFIG_IPMI_POWEROFF=m
+CONFIG_HW_RANDOM=y
+# CONFIG_HW_RANDOM_TIMERIOMEM is not set
+# CONFIG_R3964 is not set
+# CONFIG_RAW_DRIVER is not set
+# CONFIG_TCG_TPM is not set
+CONFIG_I2C=y
+CONFIG_I2C_BOARDINFO=y
+CONFIG_I2C_CHARDEV=y
+CONFIG_I2C_HELPER_AUTO=y
+CONFIG_I2C_ALGOBIT=y
+
+#
+# I2C Hardware Bus support
+#
+
+#
+# I2C system bus drivers (mostly embedded / system-on-chip)
+#
+# CONFIG_I2C_GPIO is not set
+# CONFIG_I2C_OCORES is not set
+CONFIG_I2C_S3C2410=y
+CONFIG_I2C_SIMTEC=y
+
+#
+# External I2C/SMBus adapter drivers
+#
+# CONFIG_I2C_PARPORT_LIGHT is not set
+# CONFIG_I2C_TAOS_EVM is not set
+# CONFIG_I2C_TINY_USB is not set
+
+#
+# Other I2C/SMBus bus drivers
+#
+# CONFIG_I2C_PCA_PLATFORM is not set
+# CONFIG_I2C_STUB is not set
+
+#
+# Miscellaneous I2C Chip support
+#
+# CONFIG_DS1682 is not set
+# CONFIG_SENSORS_PCF8574 is not set
+# CONFIG_PCF8575 is not set
+# CONFIG_SENSORS_PCA9539 is not set
+# CONFIG_SENSORS_MAX6875 is not set
+CONFIG_SENSORS_TSL2550=m
+# CONFIG_I2C_DEBUG_CORE is not set
+# CONFIG_I2C_DEBUG_ALGO is not set
+# CONFIG_I2C_DEBUG_BUS is not set
+# CONFIG_I2C_DEBUG_CHIP is not set
+CONFIG_SPI=y
+# CONFIG_SPI_DEBUG is not set
+CONFIG_SPI_MASTER=y
+
+#
+# SPI Master Controller Drivers
+#
+CONFIG_SPI_BITBANG=y
+# CONFIG_SPI_GPIO is not set
+CONFIG_SPI_S3C24XX=y
+# CONFIG_SPI_S3C24XX_GPIO is not set
+
+#
+# SPI Protocol Masters
+#
+CONFIG_SPI_SPIDEV=y
+# CONFIG_SPI_TLE62X0 is not set
+CONFIG_ARCH_REQUIRE_GPIOLIB=y
+CONFIG_GPIOLIB=y
+# CONFIG_DEBUG_GPIO is not set
+CONFIG_GPIO_SYSFS=y
+
+#
+# Memory mapped GPIO expanders:
+#
+
+#
+# I2C GPIO expanders:
+#
+# CONFIG_GPIO_MAX732X is not set
+# CONFIG_GPIO_PCA953X is not set
+# CONFIG_GPIO_PCF857X is not set
+
+#
+# PCI GPIO expanders:
+#
+
+#
+# SPI GPIO expanders:
+#
+# CONFIG_GPIO_MAX7301 is not set
+# CONFIG_GPIO_MCP23S08 is not set
+# CONFIG_W1 is not set
+# CONFIG_POWER_SUPPLY is not set
+CONFIG_HWMON=y
+# CONFIG_HWMON_VID is not set
+# CONFIG_SENSORS_AD7414 is not set
+# CONFIG_SENSORS_AD7418 is not set
+# CONFIG_SENSORS_ADCXX is not set
+# CONFIG_SENSORS_ADM1021 is not set
+# CONFIG_SENSORS_ADM1025 is not set
+# CONFIG_SENSORS_ADM1026 is not set
+# CONFIG_SENSORS_ADM1029 is not set
+# CONFIG_SENSORS_ADM1031 is not set
+# CONFIG_SENSORS_ADM9240 is not set
+# CONFIG_SENSORS_ADT7462 is not set
+# CONFIG_SENSORS_ADT7470 is not set
+# CONFIG_SENSORS_ADT7473 is not set
+# CONFIG_SENSORS_ADT7475 is not set
+# CONFIG_SENSORS_ATXP1 is not set
+# CONFIG_SENSORS_DS1621 is not set
+# CONFIG_SENSORS_F71805F is not set
+# CONFIG_SENSORS_F71882FG is not set
+# CONFIG_SENSORS_F75375S is not set
+# CONFIG_SENSORS_G760A is not set
+# CONFIG_SENSORS_GL518SM is not set
+# CONFIG_SENSORS_GL520SM is not set
+# CONFIG_SENSORS_IBMAEM is not set
+# CONFIG_SENSORS_IBMPEX is not set
+# CONFIG_SENSORS_IT87 is not set
+# CONFIG_SENSORS_LM63 is not set
+# CONFIG_SENSORS_LM70 is not set
+CONFIG_SENSORS_LM75=y
+# CONFIG_SENSORS_LM77 is not set
+# CONFIG_SENSORS_LM78 is not set
+# CONFIG_SENSORS_LM80 is not set
+# CONFIG_SENSORS_LM83 is not set
+# CONFIG_SENSORS_LM85 is not set
+# CONFIG_SENSORS_LM87 is not set
+# CONFIG_SENSORS_LM90 is not set
+# CONFIG_SENSORS_LM92 is not set
+# CONFIG_SENSORS_LM93 is not set
+# CONFIG_SENSORS_LTC4215 is not set
+# CONFIG_SENSORS_LTC4245 is not set
+# CONFIG_SENSORS_LM95241 is not set
+# CONFIG_SENSORS_MAX1111 is not set
+# CONFIG_SENSORS_MAX1619 is not set
+# CONFIG_SENSORS_MAX6650 is not set
+# CONFIG_SENSORS_PC87360 is not set
+# CONFIG_SENSORS_PC87427 is not set
+# CONFIG_SENSORS_PCF8591 is not set
+# CONFIG_SENSORS_SHT15 is not set
+# CONFIG_SENSORS_DME1737 is not set
+# CONFIG_SENSORS_SMSC47M1 is not set
+# CONFIG_SENSORS_SMSC47M192 is not set
+# CONFIG_SENSORS_SMSC47B397 is not set
+# CONFIG_SENSORS_ADS7828 is not set
+# CONFIG_SENSORS_THMC50 is not set
+# CONFIG_SENSORS_VT1211 is not set
+# CONFIG_SENSORS_W83781D is not set
+# CONFIG_SENSORS_W83791D is not set
+# CONFIG_SENSORS_W83792D is not set
+# CONFIG_SENSORS_W83793 is not set
+# CONFIG_SENSORS_W83L785TS is not set
+# CONFIG_SENSORS_W83L786NG is not set
+# CONFIG_SENSORS_W83627HF is not set
+# CONFIG_SENSORS_W83627EHF is not set
+# CONFIG_SENSORS_LIS3_SPI is not set
+# CONFIG_HWMON_DEBUG_CHIP is not set
+CONFIG_THERMAL=m
+# CONFIG_THERMAL_HWMON is not set
+CONFIG_WATCHDOG=y
+# CONFIG_WATCHDOG_NOWAYOUT is not set
+
+#
+# Watchdog Device Drivers
+#
+# CONFIG_SOFT_WATCHDOG is not set
+CONFIG_S3C2410_WATCHDOG=y
+
+#
+# USB-based Watchdog Cards
+#
+# CONFIG_USBPCWATCHDOG is not set
+CONFIG_SSB_POSSIBLE=y
+
+#
+# Sonics Silicon Backplane
+#
+# CONFIG_SSB is not set
+
+#
+# Multifunction device drivers
+#
+# CONFIG_MFD_CORE is not set
+# CONFIG_MFD_SM501 is not set
+# CONFIG_MFD_ASIC3 is not set
+# CONFIG_HTC_EGPIO is not set
+# CONFIG_HTC_PASIC3 is not set
+# CONFIG_TPS65010 is not set
+# CONFIG_TWL4030_CORE is not set
+# CONFIG_MFD_TMIO is not set
+# CONFIG_MFD_T7L66XB is not set
+# CONFIG_MFD_TC6387XB is not set
+# CONFIG_MFD_TC6393XB is not set
+# CONFIG_PMIC_DA903X is not set
+# CONFIG_MFD_WM8400 is not set
+# CONFIG_MFD_WM8350_I2C is not set
+# CONFIG_MFD_PCF50633 is not set
+
+#
+# Multimedia devices
+#
+
+#
+# Multimedia core support
+#
+CONFIG_VIDEO_DEV=m
+CONFIG_VIDEO_V4L2_COMMON=m
+CONFIG_VIDEO_ALLOW_V4L1=y
+CONFIG_VIDEO_V4L1_COMPAT=y
+CONFIG_DVB_CORE=m
+CONFIG_VIDEO_MEDIA=m
+
+#
+# Multimedia drivers
+#
+# CONFIG_MEDIA_ATTACH is not set
+CONFIG_MEDIA_TUNER=m
+# CONFIG_MEDIA_TUNER_CUSTOMISE is not set
+CONFIG_MEDIA_TUNER_SIMPLE=m
+CONFIG_MEDIA_TUNER_TDA8290=m
+CONFIG_MEDIA_TUNER_TDA9887=m
+CONFIG_MEDIA_TUNER_TEA5761=m
+CONFIG_MEDIA_TUNER_TEA5767=m
+CONFIG_MEDIA_TUNER_MT20XX=m
+CONFIG_MEDIA_TUNER_XC2028=m
+CONFIG_MEDIA_TUNER_XC5000=m
+CONFIG_MEDIA_TUNER_MC44S803=m
+CONFIG_VIDEO_V4L2=m
+CONFIG_VIDEO_V4L1=m
+CONFIG_VIDEOBUF_GEN=m
+CONFIG_VIDEO_CAPTURE_DRIVERS=y
+# CONFIG_VIDEO_ADV_DEBUG is not set
+# CONFIG_VIDEO_FIXED_MINOR_RANGES is not set
+CONFIG_VIDEO_HELPER_CHIPS_AUTO=y
+# CONFIG_VIDEO_VIVI is not set
+# CONFIG_VIDEO_CPIA is not set
+# CONFIG_VIDEO_CPIA2 is not set
+# CONFIG_VIDEO_SAA5246A is not set
+# CONFIG_VIDEO_SAA5249 is not set
+# CONFIG_VIDEO_AU0828 is not set
+CONFIG_SOC_CAMERA=m
+# CONFIG_SOC_CAMERA_MT9M001 is not set
+# CONFIG_SOC_CAMERA_MT9M111 is not set
+# CONFIG_SOC_CAMERA_MT9T031 is not set
+# CONFIG_SOC_CAMERA_MT9V022 is not set
+# CONFIG_SOC_CAMERA_TW9910 is not set
+CONFIG_SOC_CAMERA_PLATFORM=m
+# CONFIG_SOC_CAMERA_OV772X is not set
+# CONFIG_VIDEO_SH_MOBILE_CEU is not set
+CONFIG_V4L_USB_DRIVERS=y
+# CONFIG_USB_VIDEO_CLASS is not set
+CONFIG_USB_VIDEO_CLASS_INPUT_EVDEV=y
+CONFIG_USB_GSPCA=m
+# CONFIG_USB_M5602 is not set
+# CONFIG_USB_STV06XX is not set
+# CONFIG_USB_GSPCA_CONEX is not set
+# CONFIG_USB_GSPCA_ETOMS is not set
+# CONFIG_USB_GSPCA_FINEPIX is not set
+# CONFIG_USB_GSPCA_MARS is not set
+# CONFIG_USB_GSPCA_MR97310A is not set
+# CONFIG_USB_GSPCA_OV519 is not set
+# CONFIG_USB_GSPCA_OV534 is not set
+# CONFIG_USB_GSPCA_PAC207 is not set
+# CONFIG_USB_GSPCA_PAC7311 is not set
+# CONFIG_USB_GSPCA_SONIXB is not set
+# CONFIG_USB_GSPCA_SONIXJ is not set
+# CONFIG_USB_GSPCA_SPCA500 is not set
+# CONFIG_USB_GSPCA_SPCA501 is not set
+# CONFIG_USB_GSPCA_SPCA505 is not set
+# CONFIG_USB_GSPCA_SPCA506 is not set
+# CONFIG_USB_GSPCA_SPCA508 is not set
+# CONFIG_USB_GSPCA_SPCA561 is not set
+# CONFIG_USB_GSPCA_SQ905 is not set
+# CONFIG_USB_GSPCA_SQ905C is not set
+# CONFIG_USB_GSPCA_STK014 is not set
+# CONFIG_USB_GSPCA_SUNPLUS is not set
+# CONFIG_USB_GSPCA_T613 is not set
+# CONFIG_USB_GSPCA_TV8532 is not set
+# CONFIG_USB_GSPCA_VC032X is not set
+CONFIG_USB_GSPCA_ZC3XX=m
+# CONFIG_VIDEO_PVRUSB2 is not set
+# CONFIG_VIDEO_HDPVR is not set
+# CONFIG_VIDEO_EM28XX is not set
+# CONFIG_VIDEO_CX231XX is not set
+# CONFIG_VIDEO_USBVISION is not set
+# CONFIG_USB_VICAM is not set
+# CONFIG_USB_IBMCAM is not set
+# CONFIG_USB_KONICAWC is not set
+# CONFIG_USB_QUICKCAM_MESSENGER is not set
+# CONFIG_USB_ET61X251 is not set
+# CONFIG_VIDEO_OVCAMCHIP is not set
+# CONFIG_USB_OV511 is not set
+# CONFIG_USB_SE401 is not set
+# CONFIG_USB_SN9C102 is not set
+# CONFIG_USB_STV680 is not set
+# CONFIG_USB_ZC0301 is not set
+# CONFIG_USB_PWC is not set
+# CONFIG_USB_PWC_INPUT_EVDEV is not set
+# CONFIG_USB_ZR364XX is not set
+# CONFIG_USB_STKWEBCAM is not set
+# CONFIG_USB_S2255 is not set
+CONFIG_RADIO_ADAPTERS=y
+# CONFIG_USB_DSBR is not set
+# CONFIG_USB_SI470X is not set
+# CONFIG_USB_MR800 is not set
+# CONFIG_RADIO_TEA5764 is not set
+# CONFIG_DVB_DYNAMIC_MINORS is not set
+CONFIG_DVB_CAPTURE_DRIVERS=y
+# CONFIG_TTPCI_EEPROM is not set
+
+#
+# Supported USB Adapters
+#
+# CONFIG_DVB_USB is not set
+# CONFIG_DVB_SIANO_SMS1XXX is not set
+
+#
+# Supported FlexCopII (B2C2) Adapters
+#
+# CONFIG_DVB_B2C2_FLEXCOP is not set
+
+#
+# Supported DVB Frontends
+#
+# CONFIG_DVB_FE_CUSTOMISE is not set
+# CONFIG_DAB is not set
+
+#
+# Graphics support
+#
+# CONFIG_VGASTATE is not set
+CONFIG_VIDEO_OUTPUT_CONTROL=y
+CONFIG_FB=y
+CONFIG_FIRMWARE_EDID=y
+# CONFIG_FB_DDC is not set
+# CONFIG_FB_BOOT_VESA_SUPPORT is not set
+CONFIG_FB_CFB_FILLRECT=y
+CONFIG_FB_CFB_COPYAREA=y
+CONFIG_FB_CFB_IMAGEBLIT=y
+# CONFIG_FB_CFB_REV_PIXELS_IN_BYTE is not set
+# CONFIG_FB_SYS_FILLRECT is not set
+# CONFIG_FB_SYS_COPYAREA is not set
+# CONFIG_FB_SYS_IMAGEBLIT is not set
+# CONFIG_FB_FOREIGN_ENDIAN is not set
+# CONFIG_FB_SYS_FOPS is not set
+# CONFIG_FB_SVGALIB is not set
+# CONFIG_FB_MACMODES is not set
+# CONFIG_FB_BACKLIGHT is not set
+CONFIG_FB_MODE_HELPERS=y
+CONFIG_FB_TILEBLITTING=y
+
+#
+# Frame buffer hardware drivers
+#
+# CONFIG_FB_UVESA is not set
+# CONFIG_FB_S1D13XXX is not set
+CONFIG_FB_S3C2410=y
+# CONFIG_FB_S3C2410_DEBUG is not set
+# CONFIG_FB_VIRTUAL is not set
+# CONFIG_FB_METRONOME is not set
+# CONFIG_FB_MB862XX is not set
+# CONFIG_FB_BROADSHEET is not set
+CONFIG_BACKLIGHT_LCD_SUPPORT=y
+CONFIG_LCD_CLASS_DEVICE=y
+# CONFIG_LCD_LTV350QV is not set
+# CONFIG_LCD_ILI9320 is not set
+# CONFIG_LCD_TDO24M is not set
+# CONFIG_LCD_VGG2432A4 is not set
+CONFIG_LCD_PLATFORM=y
+CONFIG_BACKLIGHT_CLASS_DEVICE=y
+# CONFIG_BACKLIGHT_GENERIC is not set
+CONFIG_BACKLIGHT_PWM=y
+
+#
+# Display device support
+#
+CONFIG_DISPLAY_SUPPORT=y
+
+#
+# Display hardware drivers
+#
+
+#
+# Console display driver support
+#
+# CONFIG_VGA_CONSOLE is not set
+CONFIG_DUMMY_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE=y
+CONFIG_FRAMEBUFFER_CONSOLE_DETECT_PRIMARY=y
+CONFIG_FRAMEBUFFER_CONSOLE_ROTATION=y
+CONFIG_FONTS=y
+CONFIG_FONT_8x8=y
+# CONFIG_FONT_8x16 is not set
+# CONFIG_FONT_6x11 is not set
+# CONFIG_FONT_7x14 is not set
+# CONFIG_FONT_PEARL_8x8 is not set
+# CONFIG_FONT_ACORN_8x8 is not set
+CONFIG_FONT_MINI_4x6=y
+# CONFIG_FONT_SUN8x16 is not set
+# CONFIG_FONT_SUN12x22 is not set
+# CONFIG_FONT_10x18 is not set
+CONFIG_LOGO=y
+# CONFIG_LOGO_LINUX_MONO is not set
+# CONFIG_LOGO_LINUX_VGA16 is not set
+CONFIG_LOGO_LINUX_CLUT224=y
+CONFIG_SOUND=y
+CONFIG_SOUND_OSS_CORE=y
+CONFIG_SND=y
+CONFIG_SND_TIMER=y
+CONFIG_SND_PCM=y
+CONFIG_SND_HWDEP=m
+CONFIG_SND_RAWMIDI=m
+CONFIG_SND_JACK=y
+CONFIG_SND_SEQUENCER=m
+CONFIG_SND_SEQ_DUMMY=m
+CONFIG_SND_OSSEMUL=y
+CONFIG_SND_MIXER_OSS=m
+CONFIG_SND_PCM_OSS=m
+CONFIG_SND_PCM_OSS_PLUGINS=y
+CONFIG_SND_SEQUENCER_OSS=y
+CONFIG_SND_DYNAMIC_MINORS=y
+CONFIG_SND_SUPPORT_OLD_API=y
+CONFIG_SND_VERBOSE_PROCFS=y
+# CONFIG_SND_VERBOSE_PRINTK is not set
+# CONFIG_SND_DEBUG is not set
+# CONFIG_SND_DRIVERS is not set
+# CONFIG_SND_ARM is not set
+# CONFIG_SND_SPI is not set
+CONFIG_SND_USB=y
+CONFIG_SND_USB_AUDIO=m
+CONFIG_SND_USB_CAIAQ=m
+CONFIG_SND_USB_CAIAQ_INPUT=y
+CONFIG_SND_SOC=y
+CONFIG_SND_S3C24XX_SOC=y
+CONFIG_SND_S3C24XX_SOC_I2S=y
+# CONFIG_SND_S3C24XX_SOC_LN2440SBC_ALC650 is not set
+CONFIG_SND_S3C24XX_SOC_S3C24XX_UDA134X=y
+CONFIG_SND_SOC_I2C_AND_SPI=y
+# CONFIG_SND_SOC_ALL_CODECS is not set
+CONFIG_SND_SOC_L3=y
+CONFIG_SND_SOC_UDA134X=y
+# CONFIG_SOUND_PRIME is not set
+CONFIG_HID_SUPPORT=y
+CONFIG_HID=y
+# CONFIG_HID_DEBUG is not set
+CONFIG_HIDRAW=y
+
+#
+# USB Input Devices
+#
+CONFIG_USB_HID=y
+CONFIG_HID_PID=y
+CONFIG_USB_HIDDEV=y
+
+#
+# Special HID drivers
+#
+CONFIG_HID_A4TECH=y
+CONFIG_HID_APPLE=y
+CONFIG_HID_BELKIN=y
+CONFIG_HID_CHERRY=y
+CONFIG_HID_CHICONY=y
+CONFIG_HID_CYPRESS=y
+# CONFIG_DRAGONRISE_FF is not set
+CONFIG_HID_EZKEY=y
+CONFIG_HID_KYE=y
+CONFIG_HID_GYRATION=y
+CONFIG_HID_KENSINGTON=y
+CONFIG_HID_LOGITECH=y
+# CONFIG_LOGITECH_FF is not set
+# CONFIG_LOGIRUMBLEPAD2_FF is not set
+CONFIG_HID_MICROSOFT=y
+CONFIG_HID_MONTEREY=y
+CONFIG_HID_NTRIG=y
+CONFIG_HID_PANTHERLORD=y
+# CONFIG_PANTHERLORD_FF is not set
+CONFIG_HID_PETALYNX=y
+CONFIG_HID_SAMSUNG=y
+CONFIG_HID_SONY=y
+CONFIG_HID_SUNPLUS=y
+# CONFIG_GREENASIA_FF is not set
+CONFIG_HID_TOPSEED=y
+# CONFIG_THRUSTMASTER_FF is not set
+# CONFIG_ZEROPLUS_FF is not set
+CONFIG_USB_SUPPORT=y
+CONFIG_USB_ARCH_HAS_HCD=y
+CONFIG_USB_ARCH_HAS_OHCI=y
+# CONFIG_USB_ARCH_HAS_EHCI is not set
+CONFIG_USB=y
+# CONFIG_USB_DEBUG is not set
+# CONFIG_USB_ANNOUNCE_NEW_DEVICES is not set
+
+#
+# Miscellaneous USB options
+#
+CONFIG_USB_DEVICEFS=y
+# CONFIG_USB_DEVICE_CLASS is not set
+# CONFIG_USB_DYNAMIC_MINORS is not set
+# CONFIG_USB_SUSPEND is not set
+# CONFIG_USB_OTG is not set
+# CONFIG_USB_MON is not set
+# CONFIG_USB_WUSB is not set
+# CONFIG_USB_WUSB_CBAF is not set
+
+#
+# USB Host Controller Drivers
+#
+# CONFIG_USB_C67X00_HCD is not set
+# CONFIG_USB_OXU210HP_HCD is not set
+# CONFIG_USB_ISP116X_HCD is not set
+# CONFIG_USB_ISP1760_HCD is not set
+CONFIG_USB_OHCI_HCD=y
+# CONFIG_USB_OHCI_BIG_ENDIAN_DESC is not set
+# CONFIG_USB_OHCI_BIG_ENDIAN_MMIO is not set
+CONFIG_USB_OHCI_LITTLE_ENDIAN=y
+# CONFIG_USB_SL811_HCD is not set
+# CONFIG_USB_R8A66597_HCD is not set
+# CONFIG_USB_HWA_HCD is not set
+# CONFIG_USB_MUSB_HDRC is not set
+# CONFIG_USB_GADGET_MUSB_HDRC is not set
+
+#
+# USB Device Class drivers
+#
+CONFIG_USB_ACM=m
+# CONFIG_USB_PRINTER is not set
+CONFIG_USB_WDM=m
+# CONFIG_USB_TMC is not set
+
+#
+# NOTE: USB_STORAGE depends on SCSI but BLK_DEV_SD may
+#
+
+#
+# also be needed; see USB_STORAGE Help for more info
+#
+CONFIG_USB_STORAGE=m
+# CONFIG_USB_STORAGE_DEBUG is not set
+CONFIG_USB_STORAGE_DATAFAB=m
+# CONFIG_USB_STORAGE_FREECOM is not set
+CONFIG_USB_STORAGE_ISD200=m
+CONFIG_USB_STORAGE_USBAT=m
+CONFIG_USB_STORAGE_SDDR09=m
+CONFIG_USB_STORAGE_SDDR55=m
+CONFIG_USB_STORAGE_JUMPSHOT=m
+CONFIG_USB_STORAGE_ALAUDA=m
+# CONFIG_USB_STORAGE_ONETOUCH is not set
+# CONFIG_USB_STORAGE_KARMA is not set
+# CONFIG_USB_STORAGE_CYPRESS_ATACB is not set
+CONFIG_USB_LIBUSUAL=y
+
+#
+# USB Imaging devices
+#
+# CONFIG_USB_MDC800 is not set
+# CONFIG_USB_MICROTEK is not set
+
+#
+# USB port drivers
+#
+CONFIG_USB_SERIAL=m
+# CONFIG_USB_EZUSB is not set
+# CONFIG_USB_SERIAL_GENERIC is not set
+# CONFIG_USB_SERIAL_AIRCABLE is not set
+# CONFIG_USB_SERIAL_ARK3116 is not set
+# CONFIG_USB_SERIAL_BELKIN is not set
+# CONFIG_USB_SERIAL_CH341 is not set
+# CONFIG_USB_SERIAL_WHITEHEAT is not set
+# CONFIG_USB_SERIAL_DIGI_ACCELEPORT is not set
+CONFIG_USB_SERIAL_CP210X=m
+# CONFIG_USB_SERIAL_CYPRESS_M8 is not set
+# CONFIG_USB_SERIAL_EMPEG is not set
+CONFIG_USB_SERIAL_FTDI_SIO=m
+# CONFIG_USB_SERIAL_FUNSOFT is not set
+# CONFIG_USB_SERIAL_VISOR is not set
+# CONFIG_USB_SERIAL_IPAQ is not set
+# CONFIG_USB_SERIAL_IR is not set
+# CONFIG_USB_SERIAL_EDGEPORT is not set
+# CONFIG_USB_SERIAL_EDGEPORT_TI is not set
+# CONFIG_USB_SERIAL_GARMIN is not set
+# CONFIG_USB_SERIAL_IPW is not set
+# CONFIG_USB_SERIAL_IUU is not set
+# CONFIG_USB_SERIAL_KEYSPAN_PDA is not set
+# CONFIG_USB_SERIAL_KEYSPAN is not set
+# CONFIG_USB_SERIAL_KLSI is not set
+# CONFIG_USB_SERIAL_KOBIL_SCT is not set
+# CONFIG_USB_SERIAL_MCT_U232 is not set
+# CONFIG_USB_SERIAL_MOS7720 is not set
+# CONFIG_USB_SERIAL_MOS7840 is not set
+# CONFIG_USB_SERIAL_MOTOROLA is not set
+# CONFIG_USB_SERIAL_NAVMAN is not set
+# CONFIG_USB_SERIAL_PL2303 is not set
+# CONFIG_USB_SERIAL_OTI6858 is not set
+# CONFIG_USB_SERIAL_QUALCOMM is not set
+CONFIG_USB_SERIAL_SPCP8X5=m
+# CONFIG_USB_SERIAL_HP4X is not set
+# CONFIG_USB_SERIAL_SAFE is not set
+# CONFIG_USB_SERIAL_SIEMENS_MPI is not set
+# CONFIG_USB_SERIAL_SIERRAWIRELESS is not set
+# CONFIG_USB_SERIAL_SYMBOL is not set
+# CONFIG_USB_SERIAL_TI is not set
+# CONFIG_USB_SERIAL_CYBERJACK is not set
+# CONFIG_USB_SERIAL_XIRCOM is not set
+# CONFIG_USB_SERIAL_OPTION is not set
+# CONFIG_USB_SERIAL_OMNINET is not set
+# CONFIG_USB_SERIAL_OPTICON is not set
+# CONFIG_USB_SERIAL_DEBUG is not set
+
+#
+# USB Miscellaneous drivers
+#
+# CONFIG_USB_EMI62 is not set
+# CONFIG_USB_EMI26 is not set
+# CONFIG_USB_ADUTUX is not set
+# CONFIG_USB_SEVSEG is not set
+# CONFIG_USB_RIO500 is not set
+# CONFIG_USB_LEGOTOWER is not set
+# CONFIG_USB_LCD is not set
+# CONFIG_USB_BERRY_CHARGE is not set
+# CONFIG_USB_LED is not set
+# CONFIG_USB_CYPRESS_CY7C63 is not set
+# CONFIG_USB_CYTHERM is not set
+# CONFIG_USB_IDMOUSE is not set
+# CONFIG_USB_FTDI_ELAN is not set
+# CONFIG_USB_APPLEDISPLAY is not set
+# CONFIG_USB_LD is not set
+# CONFIG_USB_TRANCEVIBRATOR is not set
+# CONFIG_USB_IOWARRIOR is not set
+# CONFIG_USB_TEST is not set
+# CONFIG_USB_ISIGHTFW is not set
+# CONFIG_USB_VST is not set
+CONFIG_USB_GADGET=y
+# CONFIG_USB_GADGET_DEBUG is not set
+# CONFIG_USB_GADGET_DEBUG_FILES is not set
+# CONFIG_USB_GADGET_DEBUG_FS is not set
+CONFIG_USB_GADGET_VBUS_DRAW=2
+CONFIG_USB_GADGET_SELECTED=y
+# CONFIG_USB_GADGET_AT91 is not set
+# CONFIG_USB_GADGET_ATMEL_USBA is not set
+# CONFIG_USB_GADGET_FSL_USB2 is not set
+# CONFIG_USB_GADGET_LH7A40X is not set
+# CONFIG_USB_GADGET_OMAP is not set
+# CONFIG_USB_GADGET_PXA25X is not set
+# CONFIG_USB_GADGET_PXA27X is not set
+CONFIG_USB_GADGET_S3C2410=y
+CONFIG_USB_S3C2410=y
+# CONFIG_USB_S3C2410_DEBUG is not set
+# CONFIG_USB_GADGET_IMX is not set
+# CONFIG_USB_GADGET_M66592 is not set
+# CONFIG_USB_GADGET_AMD5536UDC is not set
+# CONFIG_USB_GADGET_FSL_QE is not set
+# CONFIG_USB_GADGET_CI13XXX is not set
+# CONFIG_USB_GADGET_NET2280 is not set
+# CONFIG_USB_GADGET_GOKU is not set
+# CONFIG_USB_GADGET_DUMMY_HCD is not set
+# CONFIG_USB_GADGET_DUALSPEED is not set
+CONFIG_USB_ZERO=m
+CONFIG_USB_ETH=m
+CONFIG_USB_ETH_RNDIS=y
+CONFIG_USB_GADGETFS=m
+CONFIG_USB_FILE_STORAGE=m
+# CONFIG_USB_FILE_STORAGE_TEST is not set
+CONFIG_USB_G_SERIAL=m
+# CONFIG_USB_MIDI_GADGET is not set
+# CONFIG_USB_G_PRINTER is not set
+CONFIG_USB_CDC_COMPOSITE=m
+
+#
+# OTG and related infrastructure
+#
+# CONFIG_USB_GPIO_VBUS is not set
+# CONFIG_NOP_USB_XCEIV is not set
+CONFIG_MMC=y
+# CONFIG_MMC_DEBUG is not set
+# CONFIG_MMC_UNSAFE_RESUME is not set
+
+#
+# MMC/SD/SDIO Card Drivers
+#
+CONFIG_MMC_BLOCK=y
+CONFIG_MMC_BLOCK_BOUNCE=y
+CONFIG_SDIO_UART=y
+# CONFIG_MMC_TEST is not set
+
+#
+# MMC/SD/SDIO Host Controller Drivers
+#
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SPI=y
+CONFIG_MMC_S3C=y
+# CONFIG_MEMSTICK is not set
+# CONFIG_ACCESSIBILITY is not set
+CONFIG_NEW_LEDS=y
+CONFIG_LEDS_CLASS=y
+
+#
+# LED drivers
+#
+CONFIG_LEDS_S3C24XX=y
+# CONFIG_LEDS_PCA9532 is not set
+CONFIG_LEDS_GPIO=y
+CONFIG_LEDS_GPIO_PLATFORM=y
+# CONFIG_LEDS_LP5521 is not set
+# CONFIG_LEDS_PCA955X is not set
+# CONFIG_LEDS_DAC124S085 is not set
+# CONFIG_LEDS_PWM is not set
+# CONFIG_LEDS_BD2802 is not set
+
+#
+# LED Triggers
+#
+CONFIG_LEDS_TRIGGERS=y
+CONFIG_LEDS_TRIGGER_TIMER=y
+CONFIG_LEDS_TRIGGER_HEARTBEAT=y
+CONFIG_LEDS_TRIGGER_BACKLIGHT=y
+CONFIG_LEDS_TRIGGER_GPIO=y
+CONFIG_LEDS_TRIGGER_DEFAULT_ON=y
+
+#
+# iptables trigger is under Netfilter config (LED target)
+#
+CONFIG_RTC_LIB=y
+CONFIG_RTC_CLASS=y
+CONFIG_RTC_HCTOSYS=y
+CONFIG_RTC_HCTOSYS_DEVICE="rtc0"
+# CONFIG_RTC_DEBUG is not set
+
+#
+# RTC interfaces
+#
+CONFIG_RTC_INTF_SYSFS=y
+CONFIG_RTC_INTF_PROC=y
+CONFIG_RTC_INTF_DEV=y
+CONFIG_RTC_INTF_DEV_UIE_EMUL=y
+# CONFIG_RTC_DRV_TEST is not set
+
+#
+# I2C RTC drivers
+#
+# CONFIG_RTC_DRV_DS1307 is not set
+# CONFIG_RTC_DRV_DS1374 is not set
+# CONFIG_RTC_DRV_DS1672 is not set
+# CONFIG_RTC_DRV_MAX6900 is not set
+# CONFIG_RTC_DRV_RS5C372 is not set
+# CONFIG_RTC_DRV_ISL1208 is not set
+# CONFIG_RTC_DRV_X1205 is not set
+# CONFIG_RTC_DRV_PCF8563 is not set
+# CONFIG_RTC_DRV_PCF8583 is not set
+# CONFIG_RTC_DRV_M41T80 is not set
+# CONFIG_RTC_DRV_S35390A is not set
+# CONFIG_RTC_DRV_FM3130 is not set
+# CONFIG_RTC_DRV_RX8581 is not set
+
+#
+# SPI RTC drivers
+#
+# CONFIG_RTC_DRV_M41T94 is not set
+# CONFIG_RTC_DRV_DS1305 is not set
+# CONFIG_RTC_DRV_DS1390 is not set
+# CONFIG_RTC_DRV_MAX6902 is not set
+# CONFIG_RTC_DRV_R9701 is not set
+# CONFIG_RTC_DRV_RS5C348 is not set
+# CONFIG_RTC_DRV_DS3234 is not set
+
+#
+# Platform RTC drivers
+#
+# CONFIG_RTC_DRV_CMOS is not set
+# CONFIG_RTC_DRV_DS1286 is not set
+# CONFIG_RTC_DRV_DS1511 is not set
+# CONFIG_RTC_DRV_DS1553 is not set
+# CONFIG_RTC_DRV_DS1742 is not set
+# CONFIG_RTC_DRV_STK17TA8 is not set
+# CONFIG_RTC_DRV_M48T86 is not set
+# CONFIG_RTC_DRV_M48T35 is not set
+# CONFIG_RTC_DRV_M48T59 is not set
+# CONFIG_RTC_DRV_BQ4802 is not set
+# CONFIG_RTC_DRV_V3020 is not set
+
+#
+# on-CPU RTC drivers
+#
+CONFIG_RTC_DRV_S3C=y
+CONFIG_DMADEVICES=y
+
+#
+# DMA Devices
+#
+# CONFIG_AUXDISPLAY is not set
+# CONFIG_REGULATOR is not set
+# CONFIG_UIO is not set
+# CONFIG_STAGING is not set
+
+#
+# File systems
+#
+CONFIG_EXT2_FS=m
+CONFIG_EXT2_FS_XATTR=y
+CONFIG_EXT2_FS_POSIX_ACL=y
+CONFIG_EXT2_FS_SECURITY=y
+# CONFIG_EXT2_FS_XIP is not set
+CONFIG_EXT3_FS=y
+# CONFIG_EXT3_DEFAULTS_TO_ORDERED is not set
+CONFIG_EXT3_FS_XATTR=y
+CONFIG_EXT3_FS_POSIX_ACL=y
+CONFIG_EXT3_FS_SECURITY=y
+# CONFIG_EXT4_FS is not set
+CONFIG_JBD=y
+# CONFIG_JBD_DEBUG is not set
+CONFIG_FS_MBCACHE=y
+# CONFIG_REISERFS_FS is not set
+# CONFIG_JFS_FS is not set
+CONFIG_FS_POSIX_ACL=y
+CONFIG_FILE_LOCKING=y
+# CONFIG_XFS_FS is not set
+# CONFIG_GFS2_FS is not set
+# CONFIG_OCFS2_FS is not set
+# CONFIG_BTRFS_FS is not set
+CONFIG_DNOTIFY=y
+CONFIG_INOTIFY=y
+CONFIG_INOTIFY_USER=y
+# CONFIG_QUOTA is not set
+CONFIG_AUTOFS_FS=y
+CONFIG_AUTOFS4_FS=y
+# CONFIG_FUSE_FS is not set
+CONFIG_GENERIC_ACL=y
+
+#
+# Caches
+#
+# CONFIG_FSCACHE is not set
+
+#
+# CD-ROM/DVD Filesystems
+#
+# CONFIG_ISO9660_FS is not set
+# CONFIG_UDF_FS is not set
+
+#
+# DOS/FAT/NT Filesystems
+#
+CONFIG_FAT_FS=y
+CONFIG_MSDOS_FS=y
+CONFIG_VFAT_FS=y
+CONFIG_FAT_DEFAULT_CODEPAGE=437
+CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1"
+# CONFIG_NTFS_FS is not set
+
+#
+# Pseudo filesystems
+#
+CONFIG_PROC_FS=y
+CONFIG_PROC_SYSCTL=y
+CONFIG_PROC_PAGE_MONITOR=y
+CONFIG_SYSFS=y
+CONFIG_TMPFS=y
+CONFIG_TMPFS_POSIX_ACL=y
+# CONFIG_HUGETLB_PAGE is not set
+CONFIG_CONFIGFS_FS=m
+CONFIG_MISC_FILESYSTEMS=y
+# CONFIG_ADFS_FS is not set
+# CONFIG_AFFS_FS is not set
+# CONFIG_ECRYPT_FS is not set
+# CONFIG_HFS_FS is not set
+# CONFIG_HFSPLUS_FS is not set
+# CONFIG_BEFS_FS is not set
+# CONFIG_BFS_FS is not set
+# CONFIG_EFS_FS is not set
+CONFIG_JFFS2_FS=y
+CONFIG_JFFS2_FS_DEBUG=0
+CONFIG_JFFS2_FS_WRITEBUFFER=y
+# CONFIG_JFFS2_FS_WBUF_VERIFY is not set
+# CONFIG_JFFS2_SUMMARY is not set
+# CONFIG_JFFS2_FS_XATTR is not set
+# CONFIG_JFFS2_COMPRESSION_OPTIONS is not set
+CONFIG_JFFS2_ZLIB=y
+# CONFIG_JFFS2_LZO is not set
+CONFIG_JFFS2_RTIME=y
+# CONFIG_JFFS2_RUBIN is not set
+CONFIG_CRAMFS=y
+# CONFIG_SQUASHFS is not set
+# CONFIG_VXFS_FS is not set
+# CONFIG_MINIX_FS is not set
+# CONFIG_OMFS_FS is not set
+# CONFIG_HPFS_FS is not set
+# CONFIG_QNX4FS_FS is not set
+CONFIG_ROMFS_FS=y
+# CONFIG_ROMFS_BACKED_BY_BLOCK is not set
+# CONFIG_ROMFS_BACKED_BY_MTD is not set
+CONFIG_ROMFS_BACKED_BY_BOTH=y
+CONFIG_ROMFS_ON_BLOCK=y
+CONFIG_ROMFS_ON_MTD=y
+# CONFIG_SYSV_FS is not set
+# CONFIG_UFS_FS is not set
+# CONFIG_NILFS2_FS is not set
+CONFIG_NETWORK_FILESYSTEMS=y
+CONFIG_NFS_FS=y
+CONFIG_NFS_V3=y
+CONFIG_NFS_V3_ACL=y
+CONFIG_NFS_V4=y
+CONFIG_ROOT_NFS=y
+# CONFIG_NFSD is not set
+CONFIG_LOCKD=y
+CONFIG_LOCKD_V4=y
+CONFIG_NFS_ACL_SUPPORT=y
+CONFIG_NFS_COMMON=y
+CONFIG_SUNRPC=y
+CONFIG_SUNRPC_GSS=y
+CONFIG_RPCSEC_GSS_KRB5=y
+# CONFIG_RPCSEC_GSS_SPKM3 is not set
+# CONFIG_SMB_FS is not set
+# CONFIG_CIFS is not set
+# CONFIG_NCP_FS is not set
+# CONFIG_CODA_FS is not set
+# CONFIG_AFS_FS is not set
+
+#
+# Partition Types
+#
+CONFIG_PARTITION_ADVANCED=y
+# CONFIG_ACORN_PARTITION is not set
+# CONFIG_OSF_PARTITION is not set
+# CONFIG_AMIGA_PARTITION is not set
+# CONFIG_ATARI_PARTITION is not set
+# CONFIG_MAC_PARTITION is not set
+CONFIG_MSDOS_PARTITION=y
+CONFIG_BSD_DISKLABEL=y
+CONFIG_MINIX_SUBPARTITION=y
+CONFIG_SOLARIS_X86_PARTITION=y
+CONFIG_UNIXWARE_DISKLABEL=y
+CONFIG_LDM_PARTITION=y
+# CONFIG_LDM_DEBUG is not set
+# CONFIG_SGI_PARTITION is not set
+# CONFIG_ULTRIX_PARTITION is not set
+# CONFIG_SUN_PARTITION is not set
+# CONFIG_KARMA_PARTITION is not set
+CONFIG_EFI_PARTITION=y
+# CONFIG_SYSV68_PARTITION is not set
+CONFIG_NLS=y
+CONFIG_NLS_DEFAULT="cp437"
+CONFIG_NLS_CODEPAGE_437=m
+CONFIG_NLS_CODEPAGE_737=m
+CONFIG_NLS_CODEPAGE_775=m
+CONFIG_NLS_CODEPAGE_850=m
+CONFIG_NLS_CODEPAGE_852=m
+CONFIG_NLS_CODEPAGE_855=m
+CONFIG_NLS_CODEPAGE_857=m
+CONFIG_NLS_CODEPAGE_860=m
+CONFIG_NLS_CODEPAGE_861=m
+CONFIG_NLS_CODEPAGE_862=m
+CONFIG_NLS_CODEPAGE_863=m
+CONFIG_NLS_CODEPAGE_864=m
+CONFIG_NLS_CODEPAGE_865=m
+CONFIG_NLS_CODEPAGE_866=m
+CONFIG_NLS_CODEPAGE_869=m
+CONFIG_NLS_CODEPAGE_936=m
+CONFIG_NLS_CODEPAGE_950=m
+CONFIG_NLS_CODEPAGE_932=m
+CONFIG_NLS_CODEPAGE_949=m
+CONFIG_NLS_CODEPAGE_874=m
+CONFIG_NLS_ISO8859_8=m
+CONFIG_NLS_CODEPAGE_1250=m
+CONFIG_NLS_CODEPAGE_1251=m
+CONFIG_NLS_ASCII=m
+CONFIG_NLS_ISO8859_1=m
+CONFIG_NLS_ISO8859_2=m
+CONFIG_NLS_ISO8859_3=m
+CONFIG_NLS_ISO8859_4=m
+CONFIG_NLS_ISO8859_5=m
+CONFIG_NLS_ISO8859_6=m
+CONFIG_NLS_ISO8859_7=m
+CONFIG_NLS_ISO8859_9=m
+CONFIG_NLS_ISO8859_13=m
+CONFIG_NLS_ISO8859_14=m
+CONFIG_NLS_ISO8859_15=m
+CONFIG_NLS_KOI8_R=m
+CONFIG_NLS_KOI8_U=m
+CONFIG_NLS_UTF8=m
+# CONFIG_DLM is not set
+
+#
+# Kernel hacking
+#
+# CONFIG_PRINTK_TIME is not set
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_FRAME_WARN=1024
+# CONFIG_MAGIC_SYSRQ is not set
+# CONFIG_UNUSED_SYMBOLS is not set
+CONFIG_DEBUG_FS=y
+# CONFIG_HEADERS_CHECK is not set
+CONFIG_DEBUG_KERNEL=y
+# CONFIG_DEBUG_SHIRQ is not set
+CONFIG_DETECT_SOFTLOCKUP=y
+# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set
+CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0
+CONFIG_DETECT_HUNG_TASK=y
+# CONFIG_BOOTPARAM_HUNG_TASK_PANIC is not set
+CONFIG_BOOTPARAM_HUNG_TASK_PANIC_VALUE=0
+# CONFIG_SCHED_DEBUG is not set
+# CONFIG_SCHEDSTATS is not set
+# CONFIG_TIMER_STATS is not set
+# CONFIG_DEBUG_OBJECTS is not set
+# CONFIG_SLUB_DEBUG_ON is not set
+# CONFIG_SLUB_STATS is not set
+# CONFIG_DEBUG_RT_MUTEXES is not set
+# CONFIG_RT_MUTEX_TESTER is not set
+# CONFIG_DEBUG_SPINLOCK is not set
+# CONFIG_DEBUG_MUTEXES is not set
+# CONFIG_DEBUG_LOCK_ALLOC is not set
+# CONFIG_PROVE_LOCKING is not set
+# CONFIG_LOCK_STAT is not set
+# CONFIG_DEBUG_SPINLOCK_SLEEP is not set
+# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set
+# CONFIG_DEBUG_KOBJECT is not set
+CONFIG_DEBUG_BUGVERBOSE=y
+CONFIG_DEBUG_INFO=y
+# CONFIG_DEBUG_VM is not set
+# CONFIG_DEBUG_WRITECOUNT is not set
+CONFIG_DEBUG_MEMORY_INIT=y
+# CONFIG_DEBUG_LIST is not set
+# CONFIG_DEBUG_SG is not set
+# CONFIG_DEBUG_NOTIFIERS is not set
+# CONFIG_BOOT_PRINTK_DELAY is not set
+# CONFIG_RCU_TORTURE_TEST is not set
+# CONFIG_RCU_CPU_STALL_DETECTOR is not set
+# CONFIG_BACKTRACE_SELF_TEST is not set
+# CONFIG_DEBUG_BLOCK_EXT_DEVT is not set
+# CONFIG_FAULT_INJECTION is not set
+# CONFIG_LATENCYTOP is not set
+CONFIG_SYSCTL_SYSCALL_CHECK=y
+# CONFIG_PAGE_POISONING is not set
+CONFIG_HAVE_FUNCTION_TRACER=y
+CONFIG_TRACING_SUPPORT=y
+
+#
+# Tracers
+#
+# CONFIG_FUNCTION_TRACER is not set
+# CONFIG_SCHED_TRACER is not set
+# CONFIG_CONTEXT_SWITCH_TRACER is not set
+# CONFIG_EVENT_TRACER is not set
+# CONFIG_BOOT_TRACER is not set
+# CONFIG_TRACE_BRANCH_PROFILING is not set
+# CONFIG_STACK_TRACER is not set
+# CONFIG_KMEMTRACE is not set
+# CONFIG_WORKQUEUE_TRACER is not set
+# CONFIG_BLK_DEV_IO_TRACE is not set
+# CONFIG_DYNAMIC_DEBUG is not set
+# CONFIG_SAMPLES is not set
+CONFIG_HAVE_ARCH_KGDB=y
+# CONFIG_KGDB is not set
+CONFIG_ARM_UNWIND=y
+CONFIG_DEBUG_USER=y
+# CONFIG_DEBUG_ERRORS is not set
+# CONFIG_DEBUG_STACK_USAGE is not set
+# CONFIG_DEBUG_LL is not set
+CONFIG_DEBUG_S3C_UART=0
+
+#
+# Security options
+#
+CONFIG_KEYS=y
+# CONFIG_KEYS_DEBUG_PROC_KEYS is not set
+# CONFIG_SECURITY is not set
+# CONFIG_SECURITYFS is not set
+CONFIG_SECURITY_FILE_CAPABILITIES=y
+CONFIG_CRYPTO=y
+
+#
+# Crypto core or helper
+#
+CONFIG_CRYPTO_FIPS=y
+CONFIG_CRYPTO_ALGAPI=y
+CONFIG_CRYPTO_ALGAPI2=y
+CONFIG_CRYPTO_AEAD=m
+CONFIG_CRYPTO_AEAD2=y
+CONFIG_CRYPTO_BLKCIPHER=y
+CONFIG_CRYPTO_BLKCIPHER2=y
+CONFIG_CRYPTO_HASH=y
+CONFIG_CRYPTO_HASH2=y
+CONFIG_CRYPTO_RNG=m
+CONFIG_CRYPTO_RNG2=y
+CONFIG_CRYPTO_PCOMP=y
+CONFIG_CRYPTO_MANAGER=y
+CONFIG_CRYPTO_MANAGER2=y
+CONFIG_CRYPTO_GF128MUL=m
+CONFIG_CRYPTO_NULL=m
+CONFIG_CRYPTO_WORKQUEUE=y
+CONFIG_CRYPTO_CRYPTD=m
+CONFIG_CRYPTO_AUTHENC=m
+CONFIG_CRYPTO_TEST=m
+
+#
+# Authenticated Encryption with Associated Data
+#
+CONFIG_CRYPTO_CCM=m
+CONFIG_CRYPTO_GCM=m
+CONFIG_CRYPTO_SEQIV=m
+
+#
+# Block modes
+#
+CONFIG_CRYPTO_CBC=y
+CONFIG_CRYPTO_CTR=m
+CONFIG_CRYPTO_CTS=m
+CONFIG_CRYPTO_ECB=y
+CONFIG_CRYPTO_LRW=m
+CONFIG_CRYPTO_PCBC=m
+CONFIG_CRYPTO_XTS=m
+
+#
+# Hash modes
+#
+CONFIG_CRYPTO_HMAC=y
+CONFIG_CRYPTO_XCBC=m
+
+#
+# Digest
+#
+CONFIG_CRYPTO_CRC32C=m
+CONFIG_CRYPTO_MD4=m
+CONFIG_CRYPTO_MD5=y
+CONFIG_CRYPTO_MICHAEL_MIC=y
+CONFIG_CRYPTO_RMD128=m
+CONFIG_CRYPTO_RMD160=m
+CONFIG_CRYPTO_RMD256=m
+CONFIG_CRYPTO_RMD320=m
+CONFIG_CRYPTO_SHA1=m
+CONFIG_CRYPTO_SHA256=m
+CONFIG_CRYPTO_SHA512=m
+CONFIG_CRYPTO_TGR192=m
+CONFIG_CRYPTO_WP512=m
+
+#
+# Ciphers
+#
+CONFIG_CRYPTO_AES=y
+CONFIG_CRYPTO_ANUBIS=m
+CONFIG_CRYPTO_ARC4=y
+CONFIG_CRYPTO_BLOWFISH=m
+CONFIG_CRYPTO_CAMELLIA=m
+CONFIG_CRYPTO_CAST5=m
+CONFIG_CRYPTO_CAST6=m
+CONFIG_CRYPTO_DES=y
+CONFIG_CRYPTO_FCRYPT=m
+CONFIG_CRYPTO_KHAZAD=m
+CONFIG_CRYPTO_SALSA20=m
+CONFIG_CRYPTO_SEED=m
+CONFIG_CRYPTO_SERPENT=m
+CONFIG_CRYPTO_TEA=m
+CONFIG_CRYPTO_TWOFISH=m
+CONFIG_CRYPTO_TWOFISH_COMMON=m
+
+#
+# Compression
+#
+CONFIG_CRYPTO_DEFLATE=m
+CONFIG_CRYPTO_ZLIB=m
+CONFIG_CRYPTO_LZO=m
+
+#
+# Random Number Generation
+#
+CONFIG_CRYPTO_ANSI_CPRNG=m
+CONFIG_CRYPTO_HW=y
+# CONFIG_BINARY_PRINTF is not set
+
+#
+# Library routines
+#
+CONFIG_BITREVERSE=y
+CONFIG_GENERIC_FIND_LAST_BIT=y
+CONFIG_CRC_CCITT=m
+CONFIG_CRC16=m
+CONFIG_CRC_T10DIF=y
+CONFIG_CRC_ITU_T=y
+CONFIG_CRC32=y
+CONFIG_CRC7=y
+CONFIG_LIBCRC32C=m
+CONFIG_ZLIB_INFLATE=y
+CONFIG_ZLIB_DEFLATE=y
+CONFIG_LZO_COMPRESS=m
+CONFIG_LZO_DECOMPRESS=m
+CONFIG_DECOMPRESS_GZIP=y
+CONFIG_DECOMPRESS_BZIP2=y
+CONFIG_DECOMPRESS_LZMA=y
+CONFIG_HAS_IOMEM=y
+CONFIG_HAS_DMA=y
+CONFIG_NLATTR=y

arch/arm/include/asm/unistd.h

@@ -389,6 +389,8 @@
 #define __NR_inotify_init1		(__NR_SYSCALL_BASE+360)
 #define __NR_preadv			(__NR_SYSCALL_BASE+361)
 #define __NR_pwritev			(__NR_SYSCALL_BASE+362)
+#define __NR_rt_tgsigqueueinfo		(__NR_SYSCALL_BASE+363)
+#define __NR_perf_counter_open		(__NR_SYSCALL_BASE+364)
 
 /*
  * The following SWIs are ARM private.

arch/arm/kernel/calls.S

@@ -372,6 +372,8 @@
 /* 360 */	CALL(sys_inotify_init1)
 		CALL(sys_preadv)
 		CALL(sys_pwritev)
+		CALL(sys_rt_tgsigqueueinfo)
+		CALL(sys_perf_counter_open)
 #ifndef syscalls_counted
 .equ syscalls_padding, ((NR_syscalls + 3) & ~3) - NR_syscalls
 #define syscalls_counted

arch/arm/kernel/irq.c

@@ -167,7 +167,7 @@ void __init init_IRQ(void)
 
 #ifdef CONFIG_SMP
 	cpumask_setall(bad_irq_desc.affinity);
-	bad_irq_desc.cpu = smp_processor_id();
+	bad_irq_desc.node = smp_processor_id();
 #endif
 	init_arch_irq();
 }
@@ -176,7 +176,7 @@ void __init init_IRQ(void)
 
 static void route_irq(struct irq_desc *desc, unsigned int irq, unsigned int cpu)
 {
-	pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->cpu, cpu);
+	pr_debug("IRQ%u: moving from cpu%u to cpu%u\n", irq, desc->node, cpu);
 
 	spin_lock_irq(&desc->lock);
 	desc->chip->set_affinity(irq, cpumask_of(cpu));
@@ -195,7 +195,7 @@ void migrate_irqs(void)
 	for (i = 0; i < NR_IRQS; i++) {
 		struct irq_desc *desc = irq_desc + i;
 
-		if (desc->cpu == cpu) {
+		if (desc->node == cpu) {
 			unsigned int newcpu = cpumask_any_and(desc->affinity,
 							      cpu_online_mask);
 			if (newcpu >= nr_cpu_ids) {

arch/arm/kernel/process.c

@@ -114,9 +114,6 @@ void arm_machine_restart(char mode, const char *cmd)
 /*
  * Function pointers to optional machine specific functions
  */
-void (*pm_idle)(void);
-EXPORT_SYMBOL(pm_idle);
-
 void (*pm_power_off)(void);
 EXPORT_SYMBOL(pm_power_off);
 
@@ -130,20 +127,19 @@ EXPORT_SYMBOL_GPL(arm_pm_restart);
  */
 static void default_idle(void)
 {
-	if (hlt_counter)
-		cpu_relax();
-	else {
-		local_irq_disable();
-		if (!need_resched())
-			arch_idle();
-		local_irq_enable();
-	}
+	if (!need_resched())
+		arch_idle();
+	local_irq_enable();
 }
 
+void (*pm_idle)(void) = default_idle;
+EXPORT_SYMBOL(pm_idle);
+
 /*
- * The idle thread.  We try to conserve power, while trying to keep
- * overall latency low.  The architecture specific idle is passed
- * a value to indicate the level of "idleness" of the system.
+ * The idle thread, has rather strange semantics for calling pm_idle,
+ * but this is what x86 does and we need to do the same, so that
+ * things like cpuidle get called in the same way.  The only difference
+ * is that we always respect 'hlt_counter' to prevent low power idle.
  */
 void cpu_idle(void)
 {
@@ -151,21 +147,31 @@ void cpu_idle(void)
 
 	/* endless idle loop with no priority at all */
 	while (1) {
-		void (*idle)(void) = pm_idle;
-
+		tick_nohz_stop_sched_tick(1);
+		leds_event(led_idle_start);
+		while (!need_resched()) {
 #ifdef CONFIG_HOTPLUG_CPU
-		if (cpu_is_offline(smp_processor_id())) {
-			leds_event(led_idle_start);
-			cpu_die();
-		}
+			if (cpu_is_offline(smp_processor_id()))
+				cpu_die();
 #endif
 
-		if (!idle)
-			idle = default_idle;
-		leds_event(led_idle_start);
-		tick_nohz_stop_sched_tick(1);
-		while (!need_resched())
-			idle();
+			local_irq_disable();
+			if (hlt_counter) {
+				local_irq_enable();
+				cpu_relax();
+			} else {
+				stop_critical_timings();
+				pm_idle();
+				start_critical_timings();
+				/*
+				 * This will eventually be removed - pm_idle
+				 * functions should always return with IRQs
+				 * enabled.
+				 */
+				WARN_ON(irqs_disabled());
+				local_irq_enable();
+			}
+		}
 		leds_event(led_idle_end);
 		tick_nohz_restart_sched_tick();
 		preempt_enable_no_resched();
@@ -352,6 +358,23 @@ asm(	".section .text\n"
 "	.size	kernel_thread_helper, . - kernel_thread_helper\n"
 "	.previous");
 
+#ifdef CONFIG_ARM_UNWIND
+extern void kernel_thread_exit(long code);
+asm(	".section .text\n"
+"	.align\n"
+"	.type	kernel_thread_exit, #function\n"
+"kernel_thread_exit:\n"
+"	.fnstart\n"
+"	.cantunwind\n"
+"	bl	do_exit\n"
+"	nop\n"
+"	.fnend\n"
+"	.size	kernel_thread_exit, . - kernel_thread_exit\n"
+"	.previous");
+#else
+#define kernel_thread_exit	do_exit
+#endif
+
 /*
  * Create a kernel thread.
  */
@@ -363,7 +386,7 @@ pid_t kernel_thread(int (*fn)(void *), void *arg, unsigned long flags)
 
 	regs.ARM_r1 = (unsigned long)arg;
 	regs.ARM_r2 = (unsigned long)fn;
-	regs.ARM_r3 = (unsigned long)do_exit;
+	regs.ARM_r3 = (unsigned long)kernel_thread_exit;
 	regs.ARM_pc = (unsigned long)kernel_thread_helper;
 	regs.ARM_cpsr = SVC_MODE | PSR_ENDSTATE;
 

arch/arm/kernel/unwind.c

@@ -212,7 +212,8 @@ static int unwind_exec_insn(struct unwind_ctrl_block *ctrl)
 			ctrl->vrs[14] = *vsp++;
 		ctrl->vrs[SP] = (unsigned long)vsp;
 	} else if (insn == 0xb0) {
-		ctrl->vrs[PC] = ctrl->vrs[LR];
+		if (ctrl->vrs[PC] == 0)
+			ctrl->vrs[PC] = ctrl->vrs[LR];
 		/* no further processing */
 		ctrl->entries = 0;
 	} else if (insn == 0xb1) {
@@ -309,18 +310,20 @@ int unwind_frame(struct stackframe *frame)
 	}
 
 	while (ctrl.entries > 0) {
-		int urc;
-
-		if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high)
-			return -URC_FAILURE;
-		urc = unwind_exec_insn(&ctrl);
+		int urc = unwind_exec_insn(&ctrl);
 		if (urc < 0)
 			return urc;
+		if (ctrl.vrs[SP] < low || ctrl.vrs[SP] >= high)
+			return -URC_FAILURE;
 	}
 
 	if (ctrl.vrs[PC] == 0)
 		ctrl.vrs[PC] = ctrl.vrs[LR];
 
+	/* check for infinite loop */
+	if (frame->pc == ctrl.vrs[PC])
+		return -URC_FAILURE;
+
 	frame->fp = ctrl.vrs[FP];
 	frame->sp = ctrl.vrs[SP];
 	frame->lr = ctrl.vrs[LR];
@@ -332,7 +335,6 @@ int unwind_frame(struct stackframe *frame)
 void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk)
 {
 	struct stackframe frame;
-	unsigned long high, low;
 	register unsigned long current_sp asm ("sp");
 
 	pr_debug("%s(regs = %p tsk = %p)\n", __func__, regs, tsk);
@@ -362,9 +364,6 @@ void unwind_backtrace(struct pt_regs *regs, struct task_struct *tsk)
 		frame.pc = thread_saved_pc(tsk);
 	}
 
-	low = frame.sp & ~(THREAD_SIZE - 1);
-	high = low + THREAD_SIZE;
-
 	while (1) {
 		int urc;
 		unsigned long where = frame.pc;

arch/arm/kernel/vmlinux.lds.S

@@ -84,6 +84,14 @@ SECTIONS
 		*(.exitcall.exit)
 		*(.ARM.exidx.exit.text)
 		*(.ARM.extab.exit.text)
+#ifndef CONFIG_HOTPLUG_CPU
+		*(.ARM.exidx.cpuexit.text)
+		*(.ARM.extab.cpuexit.text)
+#endif
+#ifndef CONFIG_HOTPLUG
+		*(.ARM.exidx.devexit.text)
+		*(.ARM.extab.devexit.text)
+#endif
 #ifndef CONFIG_MMU
 		*(.fixup)
 		*(__ex_table)

arch/arm/mach-omap2/clock.c

@@ -302,7 +302,7 @@ int omap2_wait_clock_ready(void __iomem *reg, u32 mask, const char *name)
 		udelay(1);
 	}
 
-	if (i < MAX_CLOCK_ENABLE_WAIT)
+	if (i <= MAX_CLOCK_ENABLE_WAIT)
 		pr_debug("Clock %s stable after %d loops\n", name, i);
 	else
 		printk(KERN_ERR "Clock %s didn't enable in %d tries\n",

arch/arm/mach-omap2/clock34xx.c

@@ -286,6 +286,20 @@ static struct omap_clk omap34xx_clks[] = {
 
 #define MIN_SDRC_DLL_LOCK_FREQ		83000000
 
+#define CYCLES_PER_MHZ			1000000
+
+/* Scale factor for fixed-point arith in omap3_core_dpll_m2_set_rate() */
+#define SDRC_MPURATE_SCALE		8
+
+/* 2^SDRC_MPURATE_BASE_SHIFT: MPU MHz that SDRC_MPURATE_LOOPS is defined for */
+#define SDRC_MPURATE_BASE_SHIFT		9
+
+/*
+ * SDRC_MPURATE_LOOPS: Number of MPU loops to execute at
+ * 2^MPURATE_BASE_SHIFT MHz for SDRC to stabilize
+ */
+#define SDRC_MPURATE_LOOPS		96
+
 /**
  * omap3_dpll_recalc - recalculate DPLL rate
  * @clk: DPLL struct clk
@@ -709,7 +723,8 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 {
 	u32 new_div = 0;
 	u32 unlock_dll = 0;
-	unsigned long validrate, sdrcrate;
+	u32 c;
+	unsigned long validrate, sdrcrate, mpurate;
 	struct omap_sdrc_params *sp;
 
 	if (!clk || !rate)
@@ -718,18 +733,15 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 	if (clk != &dpll3_m2_ck)
 		return -EINVAL;
 
-	if (rate == clk->rate)
-		return 0;
-
 	validrate = omap2_clksel_round_rate_div(clk, rate, &new_div);
 	if (validrate != rate)
 		return -EINVAL;
 
 	sdrcrate = sdrc_ick.rate;
 	if (rate > clk->rate)
-		sdrcrate <<= ((rate / clk->rate) - 1);
+		sdrcrate <<= ((rate / clk->rate) >> 1);
 	else
-		sdrcrate >>= ((clk->rate / rate) - 1);
+		sdrcrate >>= ((clk->rate / rate) >> 1);
 
 	sp = omap2_sdrc_get_params(sdrcrate);
 	if (!sp)
@@ -740,17 +752,25 @@ static int omap3_core_dpll_m2_set_rate(struct clk *clk, unsigned long rate)
 		unlock_dll = 1;
 	}
 
+	/*
+	 * XXX This only needs to be done when the CPU frequency changes
+	 */
+	mpurate = arm_fck.rate / CYCLES_PER_MHZ;
+	c = (mpurate << SDRC_MPURATE_SCALE) >> SDRC_MPURATE_BASE_SHIFT;
+	c += 1;  /* for safety */
+	c *= SDRC_MPURATE_LOOPS;
+	c >>= SDRC_MPURATE_SCALE;
+	if (c == 0)
+		c = 1;
+
 	pr_debug("clock: changing CORE DPLL rate from %lu to %lu\n", clk->rate,
 		 validrate);
 	pr_debug("clock: SDRC timing params used: %08x %08x %08x\n",
 		 sp->rfr_ctrl, sp->actim_ctrla, sp->actim_ctrlb);
 
-	/* REVISIT: SRAM code doesn't support other M2 divisors yet */
-	WARN_ON(new_div != 1 && new_div != 2);
-
-	/* REVISIT: Add SDRC_MR changing to this code also */
 	omap3_configure_core_dpll(sp->rfr_ctrl, sp->actim_ctrla,
-				  sp->actim_ctrlb, new_div, unlock_dll);
+				  sp->actim_ctrlb, new_div, unlock_dll, c,
+				  sp->mr, rate > clk->rate);
 
 	return 0;
 }

arch/arm/mach-omap2/io.c

@@ -21,6 +21,7 @@
 #include <linux/kernel.h>
 #include <linux/init.h>
 #include <linux/io.h>
+#include <linux/clk.h>
 
 #include <asm/tlb.h>
 
@@ -241,6 +242,40 @@ void __init omap2_map_common_io(void)
 	omapfb_reserve_sdram();
 }
 
+/*
+ * omap2_init_reprogram_sdrc - reprogram SDRC timing parameters
+ *
+ * Sets the CORE DPLL3 M2 divider to the same value that it's at
+ * currently.  This has the effect of setting the SDRC SDRAM AC timing
+ * registers to the values currently defined by the kernel.  Currently
+ * only defined for OMAP3; will return 0 if called on OMAP2.  Returns
+ * -EINVAL if the dpll3_m2_ck cannot be found, 0 if called on OMAP2,
+ * or passes along the return value of clk_set_rate().
+ */
+static int __init _omap2_init_reprogram_sdrc(void)
+{
+	struct clk *dpll3_m2_ck;
+	int v = -EINVAL;
+	long rate;
+
+	if (!cpu_is_omap34xx())
+		return 0;
+
+	dpll3_m2_ck = clk_get(NULL, "dpll3_m2_ck");
+	if (!dpll3_m2_ck)
+		return -EINVAL;
+
+	rate = clk_get_rate(dpll3_m2_ck);
+	pr_info("Reprogramming SDRC clock to %ld Hz\n", rate);
+	v = clk_set_rate(dpll3_m2_ck, rate);
+	if (v)
+		pr_err("dpll3_m2_clk rate change failed: %d\n", v);
+
+	clk_put(dpll3_m2_ck);
+
+	return v;
+}
+
 void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
 {
 	omap2_mux_init();
@@ -249,6 +284,7 @@ void __init omap2_init_common_hw(struct omap_sdrc_params *sp)
 	clkdm_init(clockdomains_omap, clkdm_pwrdm_autodeps);
 	omap2_clk_init();
 	omap2_sdrc_init(sp);
+	_omap2_init_reprogram_sdrc();
 #endif
 	gpmc_init();
 }

arch/arm/mach-omap2/powerdomain.c

@@ -1099,7 +1099,7 @@ int pwrdm_wait_transition(struct powerdomain *pwrdm)
 	       (c++ < PWRDM_TRANSITION_BAILOUT))
 		udelay(1);
 
-	if (c >= PWRDM_TRANSITION_BAILOUT) {
+	if (c > PWRDM_TRANSITION_BAILOUT) {
 		printk(KERN_ERR "powerdomain: waited too long for "
 		       "powerdomain %s to complete transition\n", pwrdm->name);
 		return -EAGAIN;

arch/arm/mach-omap2/sram34xx.S

@@ -3,13 +3,12 @@
  *
  * Omap3 specific functions that need to be run in internal SRAM
  *
- * (C) Copyright 2007
- * Texas Instruments Inc.
- * Rajendra Nayak <rnayak@ti.com>
+ * Copyright (C) 2004, 2007, 2008 Texas Instruments, Inc.
+ * Copyright (C) 2008 Nokia Corporation
  *
- * (C) Copyright 2004
- * Texas Instruments, <www.ti.com>
+ * Rajendra Nayak <rnayak@ti.com>
  * Richard Woodruff <r-woodruff2@ti.com>
+ * Paul Walmsley
  *
  * This program is free software; you can redistribute it and/or
  * modify it under the terms of the GNU General Public License as
@@ -37,61 +36,112 @@
 
 	.text
 
+/* r4 parameters */
+#define SDRC_NO_UNLOCK_DLL		0x0
+#define SDRC_UNLOCK_DLL			0x1
+
+/* SDRC_DLLA_CTRL bit settings */
+#define FIXEDDELAY_SHIFT		24
+#define FIXEDDELAY_MASK			(0xff << FIXEDDELAY_SHIFT)
+#define DLLIDLE_MASK			0x4
+
+/*
+ * SDRC_DLLA_CTRL default values: TI hardware team indicates that
+ * FIXEDDELAY should be initialized to 0xf.  This apparently was
+ * empirically determined during process testing, so no derivation
+ * was provided.
+ */
+#define FIXEDDELAY_DEFAULT		(0x0f << FIXEDDELAY_SHIFT)
+
+/* SDRC_DLLA_STATUS bit settings */
+#define LOCKSTATUS_MASK			0x4
+
+/* SDRC_POWER bit settings */
+#define SRFRONIDLEREQ_MASK		0x40
+#define PWDENA_MASK			0x4
+
+/* CM_IDLEST1_CORE bit settings */
+#define ST_SDRC_MASK			0x2
+
+/* CM_ICLKEN1_CORE bit settings */
+#define EN_SDRC_MASK			0x2
+
+/* CM_CLKSEL1_PLL bit settings */
+#define CORE_DPLL_CLKOUT_DIV_SHIFT	0x1b
+
 /*
- * Change frequency of core dpll
- * r0 = sdrc_rfr_ctrl r1 = sdrc_actim_ctrla r2 = sdrc_actim_ctrlb r3 = M2
- * r4 = Unlock SDRC DLL? (1 = yes, 0 = no) -- only unlock DLL for
+ * omap3_sram_configure_core_dpll - change DPLL3 M2 divider
+ * r0 = new SDRC_RFR_CTRL register contents
+ * r1 = new SDRC_ACTIM_CTRLA register contents
+ * r2 = new SDRC_ACTIM_CTRLB register contents
+ * r3 = new M2 divider setting (only 1 and 2 supported right now)
+ * r4 = unlock SDRC DLL? (1 = yes, 0 = no).  Only unlock DLL for
  *      SDRC rates < 83MHz
+ * r5 = number of MPU cycles to wait for SDRC to stabilize after
+ *      reprogramming the SDRC when switching to a slower MPU speed
+ * r6 = new SDRC_MR_0 register value
+ * r7 = increasing SDRC rate? (1 = yes, 0 = no)
+ *
  */
 ENTRY(omap3_sram_configure_core_dpll)
 	stmfd	sp!, {r1-r12, lr}	@ store regs to stack
 	ldr	r4, [sp, #52]		@ pull extra args off the stack
+	ldr	r5, [sp, #56]		@ load extra args from the stack
+	ldr	r6, [sp, #60]		@ load extra args from the stack
+	ldr	r7, [sp, #64]		@ load extra args from the stack
 	dsb				@ flush buffered writes to interconnect
-	cmp	r3, #0x2
-	blne	configure_sdrc
-	cmp	r4, #0x1
+	cmp	r7, #1			@ if increasing SDRC clk rate,
+	bleq	configure_sdrc		@ program the SDRC regs early (for RFR)
+	cmp	r4, #SDRC_UNLOCK_DLL	@ set the intended DLL state
 	bleq	unlock_dll
 	blne	lock_dll
-	bl	sdram_in_selfrefresh	@ put the SDRAM in self refresh
-	bl 	configure_core_dpll
-	bl	enable_sdrc
-	cmp	r4, #0x1
+	bl	sdram_in_selfrefresh	@ put SDRAM in self refresh, idle SDRC
+	bl 	configure_core_dpll	@ change the DPLL3 M2 divider
+	bl	enable_sdrc		@ take SDRC out of idle
+	cmp	r4, #SDRC_UNLOCK_DLL	@ wait for DLL status to change
 	bleq	wait_dll_unlock
 	blne	wait_dll_lock
-	cmp	r3, #0x1
-	blne	configure_sdrc
+	cmp	r7, #1			@ if increasing SDRC clk rate,
+	beq	return_to_sdram		@ return to SDRAM code, otherwise,
+	bl	configure_sdrc		@ reprogram SDRC regs now
+	mov	r12, r5
+	bl	wait_clk_stable		@ wait for SDRC to stabilize
+return_to_sdram:
 	isb				@ prevent speculative exec past here
 	mov 	r0, #0 			@ return value
 	ldmfd	sp!, {r1-r12, pc}	@ restore regs and return
 unlock_dll:
 	ldr	r11, omap3_sdrc_dlla_ctrl
 	ldr	r12, [r11]
-	orr	r12, r12, #0x4
+	and	r12, r12, #FIXEDDELAY_MASK
+	orr	r12, r12, #FIXEDDELAY_DEFAULT
+	orr	r12, r12, #DLLIDLE_MASK
 	str	r12, [r11]		@ (no OCP barrier needed)
 	bx	lr
 lock_dll:
 	ldr	r11, omap3_sdrc_dlla_ctrl
 	ldr	r12, [r11]
-	bic	r12, r12, #0x4
+	bic	r12, r12, #DLLIDLE_MASK
 	str	r12, [r11]		@ (no OCP barrier needed)
 	bx	lr
 sdram_in_selfrefresh:
 	ldr	r11, omap3_sdrc_power	@ read the SDRC_POWER register
 	ldr	r12, [r11]		@ read the contents of SDRC_POWER
 	mov	r9, r12			@ keep a copy of SDRC_POWER bits
-	orr 	r12, r12, #0x40		@ enable self refresh on idle req
-	bic 	r12, r12, #0x4		@ clear PWDENA
+	orr 	r12, r12, #SRFRONIDLEREQ_MASK	@ enable self refresh on idle
+	bic 	r12, r12, #PWDENA_MASK	@ clear PWDENA
 	str 	r12, [r11]		@ write back to SDRC_POWER register
 	ldr	r12, [r11]		@ posted-write barrier for SDRC
+idle_sdrc:
 	ldr	r11, omap3_cm_iclken1_core	@ read the CM_ICLKEN1_CORE reg
 	ldr	r12, [r11]
-	bic	r12, r12, #0x2		@ disable iclk bit for SDRC
+	bic	r12, r12, #EN_SDRC_MASK		@ disable iclk bit for SDRC
 	str 	r12, [r11]
 wait_sdrc_idle:
 	ldr 	r11, omap3_cm_idlest1_core
 	ldr 	r12, [r11]
-	and 	r12, r12, #0x2		@ check for SDRC idle
-	cmp 	r12, #2
+	and 	r12, r12, #ST_SDRC_MASK		@ check for SDRC idle
+	cmp 	r12, #ST_SDRC_MASK
 	bne 	wait_sdrc_idle
 	bx 	lr
 configure_core_dpll:
@@ -99,36 +149,23 @@ configure_core_dpll:
 	ldr	r12, [r11]
 	ldr	r10, core_m2_mask_val	@ modify m2 for core dpll
 	and	r12, r12, r10
-	orr	r12, r12, r3, lsl #0x1B	@ r3 contains the M2 val
+	orr	r12, r12, r3, lsl #CORE_DPLL_CLKOUT_DIV_SHIFT
 	str	r12, [r11]
 	ldr	r12, [r11]		@ posted-write barrier for CM
-	mov 	r12, #0x800		@ wait for the clock to stabilise
-	cmp	r3, #2
-	bne	wait_clk_stable
 	bx	lr
 wait_clk_stable:
 	subs 	r12, r12, #1
 	bne	wait_clk_stable
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
-	nop
 	bx	lr
 enable_sdrc:
 	ldr 	r11, omap3_cm_iclken1_core
 	ldr	r12, [r11]
-	orr 	r12, r12, #0x2		@ enable iclk bit for SDRC
+	orr 	r12, r12, #EN_SDRC_MASK		@ enable iclk bit for SDRC
 	str 	r12, [r11]
 wait_sdrc_idle1:
 	ldr 	r11, omap3_cm_idlest1_core
 	ldr	r12, [r11]
-	and 	r12, r12, #0x2
+	and 	r12, r12, #ST_SDRC_MASK
 	cmp	r12, #0
 	bne	wait_sdrc_idle1
 restore_sdrc_power_val:
@@ -138,14 +175,14 @@ restore_sdrc_power_val:
 wait_dll_lock:
 	ldr	r11, omap3_sdrc_dlla_status
 	ldr	r12, [r11]
-	and 	r12, r12, #0x4
-	cmp	r12, #0x4
+	and 	r12, r12, #LOCKSTATUS_MASK
+	cmp	r12, #LOCKSTATUS_MASK
 	bne	wait_dll_lock
 	bx	lr
 wait_dll_unlock:
 	ldr	r11, omap3_sdrc_dlla_status
 	ldr	r12, [r11]
-	and	r12, r12, #0x4
+	and	r12, r12, #LOCKSTATUS_MASK
 	cmp	r12, #0x0
 	bne	wait_dll_unlock
 	bx	lr
@@ -156,7 +193,9 @@ configure_sdrc:
 	str	r1, [r11]
 	ldr	r11, omap3_sdrc_actim_ctrlb
 	str	r2, [r11]
-	ldr	r2, [r11]		@ posted-write barrier for SDRC
+	ldr	r11, omap3_sdrc_mr_0
+	str	r6, [r11]
+	ldr	r6, [r11]		@ posted-write barrier for SDRC
 	bx	lr
 
 omap3_sdrc_power:
@@ -173,6 +212,8 @@ omap3_sdrc_actim_ctrla:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_A_0)
 omap3_sdrc_actim_ctrlb:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_ACTIM_CTRL_B_0)
+omap3_sdrc_mr_0:
+	.word OMAP34XX_SDRC_REGADDR(SDRC_MR_0)
 omap3_sdrc_dlla_status:
 	.word OMAP34XX_SDRC_REGADDR(SDRC_DLLA_STATUS)
 omap3_sdrc_dlla_ctrl:

arch/arm/mach-orion5x/addr-map.c

@@ -200,6 +200,6 @@ void __init orion5x_setup_pcie_wa_win(u32 base, u32 size)
 
 int __init orion5x_setup_sram_win(void)
 {
-	return setup_cpu_win(win_alloc_count, ORION5X_SRAM_PHYS_BASE,
+	return setup_cpu_win(win_alloc_count++, ORION5X_SRAM_PHYS_BASE,
 			ORION5X_SRAM_SIZE, TARGET_SRAM, ATTR_SRAM, -1);
 }

arch/arm/mach-orion5x/common.c

@@ -562,7 +562,7 @@ static struct platform_device orion5x_crypto_device = {
 	.resource       = orion5x_crypto_res,
 };
 
-int __init orion5x_crypto_init(void)
+static int __init orion5x_crypto_init(void)
 {
 	int ret;
 
@@ -696,6 +696,14 @@ void __init orion5x_init(void)
 		disable_hlt();
 	}
 
+	/*
+	 * The 5082/5181l/5182/6082/6082l/6183 have crypto
+	 * while 5180n/5181/5281 don't have crypto.
+	 */
+	if ((dev == MV88F5181_DEV_ID && rev >= MV88F5181L_REV_A0) ||
+	    dev == MV88F5182_DEV_ID || dev == MV88F6183_DEV_ID)
+		orion5x_crypto_init();
+
 	/*
 	 * Register watchdog driver
 	 */

arch/arm/mach-orion5x/common.h

@@ -38,7 +38,6 @@ void orion5x_spi_init(void);
 void orion5x_uart0_init(void);
 void orion5x_uart1_init(void);
 void orion5x_xor_init(void);
-int orion5x_crypto_init(void);
 
 /*
  * PCIe/PCI functions.

arch/arm/mach-pxa/Kconfig

@@ -401,6 +401,16 @@ config MACH_PALMZ72
 	  Say Y here if you intend to run this kernel on Palm Zire 72
 	  handheld computer.
 
+config MACH_TREO680
+	bool "Palm Treo 680"
+	default y
+	depends on ARCH_PXA_PALM
+	select PXA27x
+	select IWMMXT
+	help
+	  Say Y here if you intend to run this kernel on Palm Treo 680
+	  smartphone.
+
 config MACH_PALMLD
 	bool "Palm LifeDrive"
 	default y

arch/arm/mach-pxa/Makefile

@@ -62,6 +62,7 @@ obj-$(CONFIG_MACH_PALMT5)	+= palmt5.o
 obj-$(CONFIG_MACH_PALMTX)	+= palmtx.o
 obj-$(CONFIG_MACH_PALMLD)	+= palmld.o
 obj-$(CONFIG_MACH_PALMZ72)	+= palmz72.o
+obj-$(CONFIG_MACH_TREO680)	+= treo680.o
 obj-$(CONFIG_ARCH_VIPER)	+= viper.o
 
 ifeq ($(CONFIG_MACH_ZYLONITE),y)

arch/arm/mach-pxa/corgi.c

@@ -23,6 +23,7 @@
 #include <linux/pm.h>
 #include <linux/gpio.h>
 #include <linux/backlight.h>
+#include <linux/i2c.h>
 #include <linux/io.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
@@ -600,6 +601,10 @@ static struct platform_device *devices[] __initdata = {
 	&sharpsl_rom_device,
 };
 
+static struct i2c_board_info __initdata corgi_i2c_devices[] = {
+	{ I2C_BOARD_INFO("wm8731", 0x1b) },
+};
+
 static void corgi_poweroff(void)
 {
 	if (!machine_is_corgi())
@@ -634,6 +639,7 @@ static void __init corgi_init(void)
 	pxa_set_mci_info(&corgi_mci_platform_data);
 	pxa_set_ficp_info(&corgi_ficp_platform_data);
 	pxa_set_i2c_info(NULL);
+	i2c_register_board_info(0, ARRAY_AND_SIZE(corgi_i2c_devices));
 
 	platform_scoop_config = &corgi_pcmcia_config;
 

arch/arm/mach-pxa/em-x270.c

@@ -30,6 +30,7 @@
 #include <linux/apm-emulation.h>
 #include <linux/i2c.h>
 #include <linux/i2c/pca953x.h>
+#include <linux/regulator/userspace-consumer.h>
 
 #include <media/soc_camera.h>
 
@@ -735,6 +736,7 @@ static struct pxa2xx_spi_chip em_x270_libertas_chip = {
 	.rx_threshold	= 1,
 	.tx_threshold	= 1,
 	.timeout	= 1000,
+	.gpio_cs	= 14,
 };
 
 static unsigned long em_x270_libertas_pin_config[] = {
@@ -803,7 +805,6 @@ static int em_x270_libertas_teardown(struct spi_device *spi)
 
 struct libertas_spi_platform_data em_x270_libertas_pdata = {
 	.use_dummy_writes	= 1,
-	.gpio_cs		= 14,
 	.setup			= em_x270_libertas_setup,
 	.teardown		= em_x270_libertas_teardown,
 };
@@ -838,10 +839,14 @@ static void __init em_x270_init_spi(void)
 static inline void em_x270_init_spi(void) {}
 #endif
 
-#if defined(CONFIG_SND_PXA2XX_AC97) || defined(CONFIG_SND_PXA2XX_AC97_MODULE)
+#if defined(CONFIG_SND_PXA2XX_LIB_AC97)
+static pxa2xx_audio_ops_t em_x270_ac97_info = {
+	.reset_gpio = 113,
+};
+
 static void __init em_x270_init_ac97(void)
 {
-	pxa_set_ac97_info(NULL);
+	pxa_set_ac97_info(&em_x270_ac97_info);
 }
 #else
 static inline void em_x270_init_ac97(void) {}
@@ -1038,6 +1043,52 @@ static void  __init em_x270_init_camera(void)
 static inline void em_x270_init_camera(void) {}
 #endif
 
+static struct regulator_bulk_data em_x270_gps_consumer_supply = {
+	.supply		= "vcc gps",
+};
+
+static struct regulator_userspace_consumer_data em_x270_gps_consumer_data = {
+	.name		= "vcc gps",
+	.num_supplies	= 1,
+	.supplies	= &em_x270_gps_consumer_supply,
+};
+
+static struct platform_device em_x270_gps_userspace_consumer = {
+	.name		= "reg-userspace-consumer",
+	.id		= 0,
+	.dev		= {
+		.platform_data = &em_x270_gps_consumer_data,
+	},
+};
+
+static struct regulator_bulk_data em_x270_gprs_consumer_supply = {
+	.supply		= "vcc gprs",
+};
+
+static struct regulator_userspace_consumer_data em_x270_gprs_consumer_data = {
+	.name		= "vcc gprs",
+	.num_supplies	= 1,
+	.supplies	= &em_x270_gprs_consumer_supply
+};
+
+static struct platform_device em_x270_gprs_userspace_consumer = {
+	.name		= "reg-userspace-consumer",
+	.id		= 1,
+	.dev		= {
+		.platform_data = &em_x270_gprs_consumer_data,
+	}
+};
+
+static struct platform_device *em_x270_userspace_consumers[] = {
+	&em_x270_gps_userspace_consumer,
+	&em_x270_gprs_userspace_consumer,
+};
+
+static void __init em_x270_userspace_consumers_init(void)
+{
+	platform_add_devices(ARRAY_AND_SIZE(em_x270_userspace_consumers));
+}
+
 /* DA9030 related initializations */
 #define REGULATOR_CONSUMER(_name, _dev, _supply)			       \
 	static struct regulator_consumer_supply _name##_consumers[] = {	\
@@ -1047,11 +1098,11 @@ static inline void em_x270_init_camera(void) {}
 		},							\
 	}
 
-REGULATOR_CONSUMER(ldo3, NULL, "vcc gps");
+REGULATOR_CONSUMER(ldo3, &em_x270_gps_userspace_consumer.dev, "vcc gps");
 REGULATOR_CONSUMER(ldo5, NULL, "vcc cam");
 REGULATOR_CONSUMER(ldo10, &pxa_device_mci.dev, "vcc sdio");
 REGULATOR_CONSUMER(ldo12, NULL, "vcc usb");
-REGULATOR_CONSUMER(ldo19, NULL, "vcc gprs");
+REGULATOR_CONSUMER(ldo19, &em_x270_gprs_userspace_consumer.dev, "vcc gprs");
 
 #define REGULATOR_INIT(_ldo, _min_uV, _max_uV, _ops_mask)		\
 	static struct regulator_init_data _ldo##_data = {		\
@@ -1062,6 +1113,7 @@ REGULATOR_CONSUMER(ldo19, NULL, "vcc gprs");
 				.enabled = 0,				\
 			},						\
 			.valid_ops_mask = _ops_mask,			\
+			.apply_uV = 1,					\
 		},							\
 		.num_consumer_supplies = ARRAY_SIZE(_ldo##_consumers),	\
 		.consumer_supplies = _ldo##_consumers,			\
@@ -1240,6 +1292,7 @@ static void __init em_x270_init(void)
 	em_x270_init_spi();
 	em_x270_init_i2c();
 	em_x270_init_camera();
+	em_x270_userspace_consumers_init();
 }
 
 MACHINE_START(EM_X270, "Compulab EM-X270")

arch/arm/mach-pxa/hx4700.c

@@ -30,6 +30,7 @@
 #include <linux/pwm_backlight.h>
 #include <linux/regulator/bq24022.h>
 #include <linux/regulator/machine.h>
+#include <linux/regulator/max1586.h>
 #include <linux/spi/ads7846.h>
 #include <linux/spi/spi.h>
 #include <linux/usb/gpio_vbus.h>
@@ -774,6 +775,45 @@ static struct platform_device strataflash = {
 	},
 };
 
+/*
+ * Maxim MAX1587A on PI2C
+ */
+
+static struct regulator_consumer_supply max1587a_consumer = {
+	.supply = "vcc_core",
+};
+
+static struct regulator_init_data max1587a_v3_info = {
+	.constraints = {
+		.name = "vcc_core range",
+		.min_uV =  900000,
+		.max_uV = 1705000,
+		.always_on = 1,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies = 1,
+	.consumer_supplies     = &max1587a_consumer,
+};
+
+static struct max1586_subdev_data max1587a_subdev = {
+	.name = "vcc_core",
+	.id   = MAX1586_V3,
+	.platform_data = &max1587a_v3_info,
+};
+
+static struct max1586_platform_data max1587a_info = {
+	.num_subdevs = 1,
+	.subdevs     = &max1587a_subdev,
+	.v3_gain     = MAX1586_GAIN_R24_3k32, /* 730..1550 mV */
+};
+
+static struct i2c_board_info __initdata pi2c_board_info[] = {
+	{
+		I2C_BOARD_INFO("max1586", 0x14),
+		.platform_data = &max1587a_info,
+	},
+};
+
 /*
  * PCMCIA
  */
@@ -828,6 +868,7 @@ static void __init hx4700_init(void)
 	pxa_set_ficp_info(&ficp_info);
 	pxa27x_set_i2c_power_info(NULL);
 	pxa_set_i2c_info(NULL);
+	i2c_register_board_info(1, ARRAY_AND_SIZE(pi2c_board_info));
 	pxa2xx_set_spi_info(2, &pxa_ssp2_master_info);
 	spi_register_board_info(ARRAY_AND_SIZE(tsc2046_board_info));
 

arch/arm/mach-pxa/include/mach/palmz72.h

@@ -21,7 +21,7 @@
 /* SD/MMC */
 #define GPIO_NR_PALMZ72_SD_DETECT_N		14
 #define GPIO_NR_PALMZ72_SD_POWER_N		98
-#define GPIO_NR_PALMZ72_SD_RO 115
+#define GPIO_NR_PALMZ72_SD_RO			115
 
 /* Touchscreen */
 #define GPIO_NR_PALMZ72_WM9712_IRQ		27
@@ -31,8 +31,7 @@
 
 /* USB */
 #define GPIO_NR_PALMZ72_USB_DETECT_N		15
-#define GPIO_NR_PALMZ72_USB_POWER		95
-#define GPIO_NR_PALMZ72_USB_PULLUP		12
+#define GPIO_NR_PALMZ72_USB_PULLUP		95
 
 /* LCD/Backlight */
 #define GPIO_NR_PALMZ72_BL_POWER		20

arch/arm/mach-pxa/include/mach/treo680.h

+/*
+ * GPIOs and interrupts for Palm Treo 680 smartphone
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#ifndef _INCLUDE_TREO680_H_
+#define _INCLUDE_TREO680_H_
+
+/* GPIOs */
+#define GPIO_NR_TREO680_POWER_DETECT	0
+#define GPIO_NR_TREO680_AMP_EN		27
+#define GPIO_NR_TREO680_KEYB_BL		24
+#define GPIO_NR_TREO680_VIBRATE_EN	44
+#define GPIO_NR_TREO680_GREEN_LED	20
+#define GPIO_NR_TREO680_RED_LED		79
+#define GPIO_NR_TREO680_SD_DETECT_N	113
+#define GPIO_NR_TREO680_SD_READONLY	33
+#define GPIO_NR_TREO680_EP_DETECT_N	116
+#define GPIO_NR_TREO680_SD_POWER	42
+#define GPIO_NR_TREO680_USB_DETECT	1
+#define GPIO_NR_TREO680_USB_PULLUP	114
+#define GPIO_NR_TREO680_GSM_POWER	40
+#define GPIO_NR_TREO680_GSM_RESET	87
+#define GPIO_NR_TREO680_GSM_WAKE	57
+#define GPIO_NR_TREO680_GSM_HOST_WAKE	14
+#define GPIO_NR_TREO680_GSM_TRIGGER	10
+#define GPIO_NR_TREO680_BT_EN		43
+#define GPIO_NR_TREO680_IR_EN		115
+#define GPIO_NR_TREO680_IR_TXD		47
+#define GPIO_NR_TREO680_BL_POWER	38
+#define GPIO_NR_TREO680_LCD_POWER	25
+
+/* Various addresses  */
+#define TREO680_PHYS_RAM_START	0xa0000000
+#define TREO680_PHYS_IO_START	0x40000000
+#define TREO680_STR_BASE	0xa2000000
+
+/* BACKLIGHT */
+#define TREO680_MAX_INTENSITY		254
+#define TREO680_DEFAULT_INTENSITY	160
+#define TREO680_LIMIT_MASK		0x7F
+#define TREO680_PRESCALER		63
+#define TREO680_PERIOD_NS		3500
+
+#endif

arch/arm/mach-pxa/mioa701.c

@@ -37,6 +37,7 @@
 #include <linux/wm97xx_batt.h>
 #include <linux/mtd/physmap.h>
 #include <linux/usb/gpio_vbus.h>
+#include <linux/regulator/max1586.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -716,6 +717,38 @@ static struct wm97xx_batt_info mioa701_battery_data = {
 	.batt_name	= "mioa701_battery",
 };
 
+/*
+ * Voltage regulation
+ */
+static struct regulator_consumer_supply max1586_consumers[] = {
+	{
+		.supply = "vcc_core",
+	}
+};
+
+static struct regulator_init_data max1586_v3_info = {
+	.constraints = {
+		.name = "vcc_core range",
+		.min_uV = 1000000,
+		.max_uV = 1705000,
+		.always_on = 1,
+		.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+	},
+	.num_consumer_supplies = ARRAY_SIZE(max1586_consumers),
+	.consumer_supplies = max1586_consumers,
+};
+
+static struct max1586_subdev_data max1586_subdevs[] = {
+	{ .name = "vcc_core", .id = MAX1586_V3,
+	  .platform_data = &max1586_v3_info },
+};
+
+static struct max1586_platform_data max1586_info = {
+	.subdevs = max1586_subdevs,
+	.num_subdevs = ARRAY_SIZE(max1586_subdevs),
+	.v3_gain = MAX1586_GAIN_NO_R24, /* 700..1475 mV */
+};
+
 /*
  * Camera interface
  */
@@ -725,6 +758,13 @@ struct pxacamera_platform_data mioa701_pxacamera_platform_data = {
 	.mclk_10khz = 5000,
 };
 
+static struct i2c_board_info __initdata mioa701_pi2c_devices[] = {
+	{
+		I2C_BOARD_INFO("max1586", 0x14),
+		.platform_data = &max1586_info,
+	},
+};
+
 static struct soc_camera_link iclink = {
 	.bus_id	= 0, /* Must match id in pxa27x_device_camera in device.c */
 };
@@ -825,7 +865,9 @@ static void __init mioa701_machine_init(void)
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 	gsm_init();
 
+	i2c_register_board_info(1, ARRAY_AND_SIZE(mioa701_pi2c_devices));
 	pxa_set_i2c_info(&i2c_pdata);
+	pxa27x_set_i2c_power_info(NULL);
 	pxa_set_camera_info(&mioa701_pxacamera_platform_data);
 	i2c_register_board_info(0, ARRAY_AND_SIZE(mioa701_i2c_devices));
 }

arch/arm/mach-pxa/palmz72.c

@@ -27,7 +27,9 @@
 #include <linux/pda_power.h>
 #include <linux/pwm_backlight.h>
 #include <linux/gpio.h>
+#include <linux/wm97xx_batt.h>
 #include <linux/power_supply.h>
+#include <linux/usb/gpio_vbus.h>
 
 #include <asm/mach-types.h>
 #include <asm/mach/arch.h>
@@ -41,6 +43,8 @@
 #include <mach/irda.h>
 #include <mach/pxa27x_keypad.h>
 #include <mach/udc.h>
+#include <mach/palmasoc.h>
+
 #include <mach/pm.h>
 
 #include "generic.h"
@@ -66,6 +70,8 @@ static unsigned long palmz72_pin_config[] __initdata = {
 	GPIO29_AC97_SDATA_IN_0,
 	GPIO30_AC97_SDATA_OUT,
 	GPIO31_AC97_SYNC,
+	GPIO89_AC97_SYSCLK,
+	GPIO113_AC97_nRESET,
 
 	/* IrDA */
 	GPIO49_GPIO,	/* ir disable */
@@ -77,8 +83,7 @@ static unsigned long palmz72_pin_config[] __initdata = {
 
 	/* USB */
 	GPIO15_GPIO,	/* usb detect */
-	GPIO12_GPIO,	/* usb pullup */
-	GPIO95_GPIO,	/* usb power */
+	GPIO95_GPIO,	/* usb pullup */
 
 	/* Matrix keypad */
 	GPIO100_KP_MKIN_0	| WAKEUP_ON_LEVEL_HIGH,
@@ -354,6 +359,22 @@ static struct platform_device palmz72_leds = {
 	}
 };
 
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct gpio_vbus_mach_info palmz72_udc_info = {
+	.gpio_vbus		= GPIO_NR_PALMZ72_USB_DETECT_N,
+	.gpio_pullup		= GPIO_NR_PALMZ72_USB_PULLUP,
+};
+
+static struct platform_device palmz72_gpio_vbus = {
+	.name	= "gpio-vbus",
+	.id	= -1,
+	.dev	= {
+		.platform_data	= &palmz72_udc_info,
+	},
+};
+
 /******************************************************************************
  * Power supply
  ******************************************************************************/
@@ -421,6 +442,31 @@ static struct platform_device power_supply = {
 	},
 };
 
+/******************************************************************************
+ * WM97xx battery
+ ******************************************************************************/
+static struct wm97xx_batt_info wm97xx_batt_pdata = {
+	.batt_aux	= WM97XX_AUX_ID3,
+	.temp_aux	= WM97XX_AUX_ID2,
+	.charge_gpio	= -1,
+	.max_voltage	= PALMZ72_BAT_MAX_VOLTAGE,
+	.min_voltage	= PALMZ72_BAT_MIN_VOLTAGE,
+	.batt_mult	= 1000,
+	.batt_div	= 414,
+	.temp_mult	= 1,
+	.temp_div	= 1,
+	.batt_tech	= POWER_SUPPLY_TECHNOLOGY_LIPO,
+	.batt_name	= "main-batt",
+};
+
+/******************************************************************************
+ * aSoC audio
+ ******************************************************************************/
+static struct platform_device palmz72_asoc = {
+	.name = "palm27x-asoc",
+	.id   = -1,
+};
+
 /******************************************************************************
  * Framebuffer
  ******************************************************************************/
@@ -527,17 +573,32 @@ device_initcall(palmz72_pm_init);
 static struct platform_device *devices[] __initdata = {
 	&palmz72_backlight,
 	&palmz72_leds,
+	&palmz72_asoc,
 	&power_supply,
+	&palmz72_gpio_vbus,
 };
 
+/* setup udc GPIOs initial state */
+static void __init palmz72_udc_init(void)
+{
+	if (!gpio_request(GPIO_NR_PALMZ72_USB_PULLUP, "USB Pullup")) {
+		gpio_direction_output(GPIO_NR_PALMZ72_USB_PULLUP, 0);
+		gpio_free(GPIO_NR_PALMZ72_USB_PULLUP);
+	}
+}
+
 static void __init palmz72_init(void)
 {
 	pxa2xx_mfp_config(ARRAY_AND_SIZE(palmz72_pin_config));
+
 	set_pxa_fb_info(&palmz72_lcd_screen);
 	pxa_set_mci_info(&palmz72_mci_platform_data);
+	palmz72_udc_init();
 	pxa_set_ac97_info(NULL);
 	pxa_set_ficp_info(&palmz72_ficp_platform_data);
 	pxa_set_keypad_info(&palmz72_keypad_platform_data);
+	wm97xx_bat_set_pdata(&wm97xx_batt_pdata);
+
 	platform_add_devices(devices, ARRAY_SIZE(devices));
 }
 

arch/arm/mach-pxa/poodle.c

@@ -22,6 +22,7 @@
 #include <linux/delay.h>
 #include <linux/mtd/physmap.h>
 #include <linux/gpio.h>
+#include <linux/i2c.h>
 #include <linux/spi/spi.h>
 #include <linux/spi/ads7846.h>
 #include <linux/mtd/sharpsl.h>
@@ -486,6 +487,10 @@ static struct platform_device *devices[] __initdata = {
 	&sharpsl_rom_device,
 };
 
+static struct i2c_board_info __initdata poodle_i2c_devices[] = {
+	{ I2C_BOARD_INFO("wm8731", 0x1b) },
+};
+
 static void poodle_poweroff(void)
 {
 	arm_machine_restart('h', NULL);
@@ -519,6 +524,7 @@ static void __init poodle_init(void)
 	pxa_set_mci_info(&poodle_mci_platform_data);
 	pxa_set_ficp_info(&poodle_ficp_platform_data);
 	pxa_set_i2c_info(NULL);
+	i2c_register_board_info(0, ARRAY_AND_SIZE(poodle_i2c_devices));
 	poodle_init_spi();
 }
 

arch/arm/mach-pxa/treo680.c

+/*
+ * Hardware definitions for Palm Treo 680
+ *
+ * Author:     Tomas Cech <sleep_walker@suse.cz>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * (find more info at www.hackndev.com)
+ *
+ */
+
+#include <linux/platform_device.h>
+#include <linux/delay.h>
+#include <linux/irq.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/pda_power.h>
+#include <linux/pwm_backlight.h>
+#include <linux/gpio.h>
+#include <linux/wm97xx_batt.h>
+#include <linux/power_supply.h>
+#include <linux/sysdev.h>
+#include <linux/w1-gpio.h>
+
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/pxa27x.h>
+#include <mach/pxa27x-udc.h>
+#include <mach/audio.h>
+#include <mach/treo680.h>
+#include <mach/mmc.h>
+#include <mach/pxafb.h>
+#include <mach/irda.h>
+#include <mach/pxa27x_keypad.h>
+#include <mach/udc.h>
+#include <mach/ohci.h>
+#include <mach/pxa2xx-regs.h>
+#include <mach/palmasoc.h>
+#include <mach/camera.h>
+
+#include <sound/pxa2xx-lib.h>
+
+#include "generic.h"
+#include "devices.h"
+
+/******************************************************************************
+ * Pin configuration
+ ******************************************************************************/
+static unsigned long treo680_pin_config[] __initdata = {
+	/* MMC */
+	GPIO32_MMC_CLK,
+	GPIO92_MMC_DAT_0,
+	GPIO109_MMC_DAT_1,
+	GPIO110_MMC_DAT_2,
+	GPIO111_MMC_DAT_3,
+	GPIO112_MMC_CMD,
+	GPIO33_GPIO,				/* SD read only */
+	GPIO113_GPIO,				/* SD detect */
+
+	/* AC97 */
+	GPIO28_AC97_BITCLK,
+	GPIO29_AC97_SDATA_IN_0,
+	GPIO30_AC97_SDATA_OUT,
+	GPIO31_AC97_SYNC,
+	GPIO89_AC97_SYSCLK,
+	GPIO95_AC97_nRESET,
+
+	/* IrDA */
+	GPIO46_FICP_RXD,
+	GPIO47_FICP_TXD,
+
+	/* PWM */
+	GPIO16_PWM0_OUT,
+
+	/* USB */
+	GPIO1_GPIO | WAKEUP_ON_EDGE_BOTH,	/* usb detect */
+
+	/* MATRIX KEYPAD */
+	GPIO100_KP_MKIN_0 | WAKEUP_ON_LEVEL_HIGH,
+	GPIO101_KP_MKIN_1,
+	GPIO102_KP_MKIN_2,
+	GPIO97_KP_MKIN_3,
+	GPIO98_KP_MKIN_4,
+	GPIO99_KP_MKIN_5,
+	GPIO91_KP_MKIN_6,
+	GPIO13_KP_MKIN_7,
+	GPIO103_KP_MKOUT_0 | MFP_LPM_DRIVE_HIGH,
+	GPIO104_KP_MKOUT_1,
+	GPIO105_KP_MKOUT_2,
+	GPIO106_KP_MKOUT_3,
+	GPIO107_KP_MKOUT_4,
+	GPIO108_KP_MKOUT_5,
+	GPIO96_KP_MKOUT_6,
+	GPIO93_KP_DKIN_0 | WAKEUP_ON_LEVEL_HIGH,	/* Hotsync button */
+
+	/* LCD */
+	GPIO58_LCD_LDD_0,
+	GPIO59_LCD_LDD_1,
+	GPIO60_LCD_LDD_2,
+	GPIO61_LCD_LDD_3,
+	GPIO62_LCD_LDD_4,
+	GPIO63_LCD_LDD_5,
+	GPIO64_LCD_LDD_6,
+	GPIO65_LCD_LDD_7,
+	GPIO66_LCD_LDD_8,
+	GPIO67_LCD_LDD_9,
+	GPIO68_LCD_LDD_10,
+	GPIO69_LCD_LDD_11,
+	GPIO70_LCD_LDD_12,
+	GPIO71_LCD_LDD_13,
+	GPIO72_LCD_LDD_14,
+	GPIO73_LCD_LDD_15,
+	GPIO74_LCD_FCLK,
+	GPIO75_LCD_LCLK,
+	GPIO76_LCD_PCLK,
+
+	/* Quick Capture Interface */
+	GPIO84_CIF_FV,
+	GPIO85_CIF_LV,
+	GPIO53_CIF_MCLK,
+	GPIO54_CIF_PCLK,
+	GPIO81_CIF_DD_0,
+	GPIO55_CIF_DD_1,
+	GPIO51_CIF_DD_2,
+	GPIO50_CIF_DD_3,
+	GPIO52_CIF_DD_4,
+	GPIO48_CIF_DD_5,
+	GPIO17_CIF_DD_6,
+	GPIO12_CIF_DD_7,
+
+	/* I2C */
+	GPIO117_I2C_SCL,
+	GPIO118_I2C_SDA,
+
+	/* GSM */
+	GPIO14_GPIO | WAKEUP_ON_EDGE_BOTH,	/* GSM host wake up */
+	GPIO34_FFUART_RXD,
+	GPIO35_FFUART_CTS,
+	GPIO39_FFUART_TXD,
+	GPIO41_FFUART_RTS,
+
+	/* MISC. */
+	GPIO0_GPIO | WAKEUP_ON_EDGE_BOTH,	/* external power detect */
+	GPIO15_GPIO | WAKEUP_ON_EDGE_BOTH,	/* silent switch */
+	GPIO116_GPIO,				/* headphone detect */
+	GPIO11_GPIO | WAKEUP_ON_EDGE_BOTH,	/* bluetooth host wake up */
+};
+
+/******************************************************************************
+ * SD/MMC card controller
+ ******************************************************************************/
+static int treo680_mci_init(struct device *dev,
+		irq_handler_t treo680_detect_int, void *data)
+{
+	int err = 0;
+
+	/* Setup an interrupt for detecting card insert/remove events */
+	err = gpio_request(GPIO_NR_TREO680_SD_DETECT_N, "SD IRQ");
+
+	if (err)
+		goto err;
+
+	err = gpio_direction_input(GPIO_NR_TREO680_SD_DETECT_N);
+	if (err)
+		goto err2;
+
+	err = request_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N),
+			treo680_detect_int, IRQF_DISABLED | IRQF_SAMPLE_RANDOM |
+			IRQF_TRIGGER_FALLING | IRQF_TRIGGER_RISING,
+			"SD/MMC card detect", data);
+
+	if (err) {
+		dev_err(dev, "%s: cannot request SD/MMC card detect IRQ\n",
+			     __func__);
+		goto err2;
+	}
+
+	err = gpio_request(GPIO_NR_TREO680_SD_POWER, "SD_POWER");
+	if (err)
+		goto err3;
+
+	err = gpio_direction_output(GPIO_NR_TREO680_SD_POWER, 1);
+	if (err)
+		goto err4;
+
+	err = gpio_request(GPIO_NR_TREO680_SD_READONLY, "SD_READONLY");
+	if (err)
+		goto err4;
+
+	err = gpio_direction_input(GPIO_NR_TREO680_SD_READONLY);
+	if (err)
+		goto err5;
+
+	return 0;
+
+err5:
+	gpio_free(GPIO_NR_TREO680_SD_READONLY);
+err4:
+	gpio_free(GPIO_NR_TREO680_SD_POWER);
+err3:
+	free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
+err2:
+	gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
+err:
+	return err;
+}
+
+static void treo680_mci_exit(struct device *dev, void *data)
+{
+	gpio_free(GPIO_NR_TREO680_SD_READONLY);
+	gpio_free(GPIO_NR_TREO680_SD_POWER);
+	free_irq(gpio_to_irq(GPIO_NR_TREO680_SD_DETECT_N), data);
+	gpio_free(GPIO_NR_TREO680_SD_DETECT_N);
+}
+
+static void treo680_mci_power(struct device *dev, unsigned int vdd)
+{
+	struct pxamci_platform_data *p_d = dev->platform_data;
+	gpio_set_value(GPIO_NR_TREO680_SD_POWER, p_d->ocr_mask & (1 << vdd));
+}
+
+static int treo680_mci_get_ro(struct device *dev)
+{
+	return gpio_get_value(GPIO_NR_TREO680_SD_READONLY);
+}
+
+static struct pxamci_platform_data treo680_mci_platform_data = {
+	.ocr_mask	= MMC_VDD_32_33 | MMC_VDD_33_34,
+	.setpower	= treo680_mci_power,
+	.get_ro		= treo680_mci_get_ro,
+	.init 		= treo680_mci_init,
+	.exit		= treo680_mci_exit,
+};
+
+/******************************************************************************
+ * GPIO keyboard
+ ******************************************************************************/
+static unsigned int treo680_matrix_keys[] = {
+	KEY(0, 0, KEY_F8),		/* Red/Off/Power */
+	KEY(0, 1, KEY_LEFT),
+	KEY(0, 2, KEY_LEFTCTRL),	/* Alternate */
+	KEY(0, 3, KEY_L),
+	KEY(0, 4, KEY_A),
+	KEY(0, 5, KEY_Q),
+	KEY(0, 6, KEY_P),
+
+	KEY(1, 0, KEY_RIGHTCTRL),	/* Menu */
+	KEY(1, 1, KEY_RIGHT),
+	KEY(1, 2, KEY_LEFTSHIFT),	/* Left shift */
+	KEY(1, 3, KEY_Z),
+	KEY(1, 4, KEY_S),
+	KEY(1, 5, KEY_W),
+
+	KEY(2, 0, KEY_F1),		/* Phone */
+	KEY(2, 1, KEY_UP),
+	KEY(2, 2, KEY_0),
+	KEY(2, 3, KEY_X),
+	KEY(2, 4, KEY_D),
+	KEY(2, 5, KEY_E),
+
+	KEY(3, 0, KEY_F10),		/* Calendar */
+	KEY(3, 1, KEY_DOWN),
+	KEY(3, 2, KEY_SPACE),
+	KEY(3, 3, KEY_C),
+	KEY(3, 4, KEY_F),
+	KEY(3, 5, KEY_R),
+
+	KEY(4, 0, KEY_F12),		/* Mail */
+	KEY(4, 1, KEY_KPENTER),
+	KEY(4, 2, KEY_RIGHTALT),	/* Alt */
+	KEY(4, 3, KEY_V),
+	KEY(4, 4, KEY_G),
+	KEY(4, 5, KEY_T),
+
+	KEY(5, 0, KEY_F9),		/* Home */
+	KEY(5, 1, KEY_PAGEUP),		/* Side up */
+	KEY(5, 2, KEY_DOT),
+	KEY(5, 3, KEY_B),
+	KEY(5, 4, KEY_H),
+	KEY(5, 5, KEY_Y),
+
+	KEY(6, 0, KEY_TAB),		/* Side Activate */
+	KEY(6, 1, KEY_PAGEDOWN),	/* Side down */
+	KEY(6, 2, KEY_ENTER),
+	KEY(6, 3, KEY_N),
+	KEY(6, 4, KEY_J),
+	KEY(6, 5, KEY_U),
+
+	KEY(7, 0, KEY_F6),		/* Green/Call */
+	KEY(7, 1, KEY_O),
+	KEY(7, 2, KEY_BACKSPACE),
+	KEY(7, 3, KEY_M),
+	KEY(7, 4, KEY_K),
+	KEY(7, 5, KEY_I),
+};
+
+static struct pxa27x_keypad_platform_data treo680_keypad_platform_data = {
+	.matrix_key_rows	= 8,
+	.matrix_key_cols	= 7,
+	.matrix_key_map		= treo680_matrix_keys,
+	.matrix_key_map_size	= ARRAY_SIZE(treo680_matrix_keys),
+	.direct_key_map		= { KEY_CONNECT },
+	.direct_key_num		= 1,
+
+	.debounce_interval	= 30,
+};
+
+/******************************************************************************
+ * aSoC audio
+ ******************************************************************************/
+
+static pxa2xx_audio_ops_t treo680_ac97_pdata = {
+	.reset_gpio	= 95,
+};
+
+/******************************************************************************
+ * Backlight
+ ******************************************************************************/
+static int treo680_backlight_init(struct device *dev)
+{
+	int ret;
+
+	ret = gpio_request(GPIO_NR_TREO680_BL_POWER, "BL POWER");
+	if (ret)
+		goto err;
+	ret = gpio_direction_output(GPIO_NR_TREO680_BL_POWER, 0);
+	if (ret)
+		goto err2;
+	ret = gpio_request(GPIO_NR_TREO680_LCD_POWER, "LCD POWER");
+	if (ret)
+		goto err2;
+	ret = gpio_direction_output(GPIO_NR_TREO680_LCD_POWER, 0);
+	if (ret)
+		goto err3;
+
+	return 0;
+err3:
+	gpio_free(GPIO_NR_TREO680_LCD_POWER);
+err2:
+	gpio_free(GPIO_NR_TREO680_BL_POWER);
+err:
+	return ret;
+}
+
+static int treo680_backlight_notify(int brightness)
+{
+	gpio_set_value(GPIO_NR_TREO680_BL_POWER, brightness);
+	return TREO680_MAX_INTENSITY - brightness;
+};
+
+static void treo680_backlight_exit(struct device *dev)
+{
+	gpio_free(GPIO_NR_TREO680_BL_POWER);
+	gpio_free(GPIO_NR_TREO680_LCD_POWER);
+}
+
+static struct platform_pwm_backlight_data treo680_backlight_data = {
+	.pwm_id		= 0,
+	.max_brightness	= TREO680_MAX_INTENSITY,
+	.dft_brightness	= TREO680_DEFAULT_INTENSITY,
+	.pwm_period_ns	= TREO680_PERIOD_NS,
+	.init		= treo680_backlight_init,
+	.notify		= treo680_backlight_notify,
+	.exit		= treo680_backlight_exit,
+};
+
+static struct platform_device treo680_backlight = {
+	.name	= "pwm-backlight",
+	.dev	= {
+		.parent		= &pxa27x_device_pwm0.dev,
+		.platform_data	= &treo680_backlight_data,
+	},
+};
+
+/******************************************************************************
+ * IrDA
+ ******************************************************************************/
+static void treo680_transceiver_mode(struct device *dev, int mode)
+{
+	gpio_set_value(GPIO_NR_TREO680_IR_EN, mode & IR_OFF);
+	pxa2xx_transceiver_mode(dev, mode);
+}
+
+static int treo680_irda_startup(struct device *dev)
+{
+	int err;
+
+	err = gpio_request(GPIO_NR_TREO680_IR_EN, "Ir port disable");
+	if (err)
+		goto err1;
+
+	err = gpio_direction_output(GPIO_NR_TREO680_IR_EN, 1);
+	if (err)
+		goto err2;
+
+	return 0;
+
+err2:
+	dev_err(dev, "treo680_irda: cannot change IR gpio direction\n");
+	gpio_free(GPIO_NR_TREO680_IR_EN);
+err1:
+	dev_err(dev, "treo680_irda: cannot allocate IR gpio\n");
+	return err;
+}
+
+static void treo680_irda_shutdown(struct device *dev)
+{
+	gpio_free(GPIO_NR_TREO680_AMP_EN);
+}
+
+static struct pxaficp_platform_data treo680_ficp_info = {
+	.transceiver_cap  = IR_FIRMODE | IR_SIRMODE | IR_OFF,
+	.startup          = treo680_irda_startup,
+	.shutdown         = treo680_irda_shutdown,
+	.transceiver_mode = treo680_transceiver_mode,
+};
+
+/******************************************************************************
+ * UDC
+ ******************************************************************************/
+static struct pxa2xx_udc_mach_info treo680_udc_info __initdata = {
+	.gpio_vbus		= GPIO_NR_TREO680_USB_DETECT,
+	.gpio_vbus_inverted	= 1,
+	.gpio_pullup		= GPIO_NR_TREO680_USB_PULLUP,
+};
+
+
+/******************************************************************************
+ * USB host
+ ******************************************************************************/
+static struct pxaohci_platform_data treo680_ohci_info = {
+	.port_mode    = PMM_PERPORT_MODE,
+	.flags        = ENABLE_PORT1 | ENABLE_PORT3,
+	.power_budget = 0,
+};
+
+/******************************************************************************
+ * Power supply
+ ******************************************************************************/
+static int power_supply_init(struct device *dev)
+{
+	int ret;
+
+	ret = gpio_request(GPIO_NR_TREO680_POWER_DETECT, "CABLE_STATE_AC");
+	if (ret)
+		goto err1;
+	ret = gpio_direction_input(GPIO_NR_TREO680_POWER_DETECT);
+	if (ret)
+		goto err2;
+
+	return 0;
+
+err2:
+	gpio_free(GPIO_NR_TREO680_POWER_DETECT);
+err1:
+	return ret;
+}
+
+static int treo680_is_ac_online(void)
+{
+	return gpio_get_value(GPIO_NR_TREO680_POWER_DETECT);
+}
+
+static void power_supply_exit(struct device *dev)
+{
+	gpio_free(GPIO_NR_TREO680_POWER_DETECT);
+}
+
+static char *treo680_supplicants[] = {
+	"main-battery",
+};
+
+static struct pda_power_pdata power_supply_info = {
+	.init		 = power_supply_init,
+	.is_ac_online    = treo680_is_ac_online,
+	.exit		 = power_supply_exit,
+	.supplied_to     = treo680_supplicants,
+	.num_supplicants = ARRAY_SIZE(treo680_supplicants),
+};
+
+static struct platform_device power_supply = {
+	.name = "pda-power",
+	.id   = -1,
+	.dev  = {
+		.platform_data = &power_supply_info,
+	},
+};
+
+/******************************************************************************
+ * Vibra and LEDs
+ ******************************************************************************/
+static struct gpio_led gpio_leds[] = {
+	{
+		.name			= "treo680:vibra:vibra",
+		.default_trigger	= "none",
+		.gpio			= GPIO_NR_TREO680_VIBRATE_EN,
+	},
+	{
+		.name			= "treo680:green:led",
+		.default_trigger	= "mmc0",
+		.gpio			= GPIO_NR_TREO680_GREEN_LED,
+	},
+	{
+		.name			= "treo680:keybbl:keybbl",
+		.default_trigger	= "none",
+		.gpio			= GPIO_NR_TREO680_KEYB_BL,
+	},
+};
+
+static struct gpio_led_platform_data gpio_led_info = {
+	.leds		= gpio_leds,
+	.num_leds	= ARRAY_SIZE(gpio_leds),
+};
+
+static struct platform_device treo680_leds = {
+	.name   = "leds-gpio",
+	.id     = -1,
+	.dev    = {
+		.platform_data  = &gpio_led_info,
+	}
+};
+
+
+/******************************************************************************
+ * Framebuffer
+ ******************************************************************************/
+/* TODO: add support for 324x324 */
+static struct pxafb_mode_info treo680_lcd_modes[] = {
+{
+	.pixclock		= 86538,
+	.xres			= 320,
+	.yres			= 320,
+	.bpp			= 16,
+
+	.left_margin		= 20,
+	.right_margin		= 8,
+	.upper_margin		= 8,
+	.lower_margin		= 5,
+
+	.hsync_len		= 4,
+	.vsync_len		= 1,
+},
+};
+
+static struct pxafb_mach_info treo680_lcd_screen = {
+	.modes		= treo680_lcd_modes,
+	.num_modes	= ARRAY_SIZE(treo680_lcd_modes),
+	.lcd_conn	= LCD_COLOR_TFT_16BPP | LCD_PCLK_EDGE_FALL,
+};
+
+/******************************************************************************
+ * Power management - standby
+ ******************************************************************************/
+static void __init treo680_pm_init(void)
+{
+	static u32 resume[] = {
+		0xe3a00101,	/* mov	r0,	#0x40000000 */
+		0xe380060f,	/* orr	r0, r0, #0x00f00000 */
+		0xe590f008,	/* ldr	pc, [r0, #0x08] */
+	};
+
+	/* this is where the bootloader jumps */
+	memcpy(phys_to_virt(TREO680_STR_BASE), resume, sizeof(resume));
+}
+
+/******************************************************************************
+ * Machine init
+ ******************************************************************************/
+static struct platform_device *devices[] __initdata = {
+	&treo680_backlight,
+	&treo680_leds,
+	&power_supply,
+};
+
+/* setup udc GPIOs initial state */
+static void __init treo680_udc_init(void)
+{
+	if (!gpio_request(GPIO_NR_TREO680_USB_PULLUP, "UDC Vbus")) {
+		gpio_direction_output(GPIO_NR_TREO680_USB_PULLUP, 1);
+		gpio_free(GPIO_NR_TREO680_USB_PULLUP);
+	}
+}
+
+static void __init treo680_init(void)
+{
+	treo680_pm_init();
+	pxa2xx_mfp_config(ARRAY_AND_SIZE(treo680_pin_config));
+	pxa_set_keypad_info(&treo680_keypad_platform_data);
+	set_pxa_fb_info(&treo680_lcd_screen);
+	pxa_set_mci_info(&treo680_mci_platform_data);
+	treo680_udc_init();
+	pxa_set_udc_info(&treo680_udc_info);
+	pxa_set_ac97_info(&treo680_ac97_pdata);
+	pxa_set_ficp_info(&treo680_ficp_info);
+	pxa_set_ohci_info(&treo680_ohci_info);
+
+	platform_add_devices(devices, ARRAY_SIZE(devices));
+}
+
+MACHINE_START(TREO680, "Palm Treo 680")
+	.phys_io	= TREO680_PHYS_IO_START,
+	.io_pg_offst	= io_p2v(0x40000000),
+	.boot_params	= 0xa0000100,
+	.map_io		= pxa_map_io,
+	.init_irq	= pxa27x_init_irq,
+	.timer		= &pxa_timer,
+	.init_machine	= treo680_init,
+MACHINE_END

arch/arm/mach-realview/realview_pbx.c

@@ -27,6 +27,7 @@
 #include <asm/irq.h>
 #include <asm/leds.h>
 #include <asm/mach-types.h>
+#include <asm/smp_twd.h>
 #include <asm/hardware/gic.h>
 #include <asm/hardware/cache-l2x0.h>
 

arch/arm/mach-s3c2410/usb-simtec.c

@@ -22,7 +22,6 @@
 #include <linux/timer.h>
 #include <linux/init.h>
 #include <linux/device.h>
-#include <linux/gpio.h>
 #include <linux/io.h>
 
 #include <asm/mach/arch.h>

arch/arm/mach-s3c2440/Kconfig

@@ -84,5 +84,15 @@ config MACH_AT2440EVB
 	help
 	  Say Y here if you are using the AT2440EVB development board
 
+config MACH_MINI2440
+	bool "MINI2440 development board"
+	select CPU_S3C2440
+	select EEPROM_AT24
+	select LEDS_TRIGGER_BACKLIGHT
+	select SND_S3C24XX_SOC_S3C24XX_UDA134X
+	help
+	  Say Y here to select support for the MINI2440. Is a 10cm x 10cm board
+	  available via various sources. It can come with a 3.5" or 7" touch LCD.
+
 endmenu
 

arch/arm/mach-s3c2440/Makefile

@@ -22,3 +22,4 @@ obj-$(CONFIG_MACH_RX3715)	+= mach-rx3715.o
 obj-$(CONFIG_ARCH_S3C2440)	+= mach-smdk2440.o
 obj-$(CONFIG_MACH_NEXCODER_2440) += mach-nexcoder.o
 obj-$(CONFIG_MACH_AT2440EVB) += mach-at2440evb.o
+obj-$(CONFIG_MACH_MINI2440) += mach-mini2440.o

arch/arm/mach-s3c2440/mach-mini2440.c

+/* linux/arch/arm/mach-s3c2440/mach-mini2440.c
+ *
+ * Copyright (c) 2008 Ramax Lo <ramaxlo@gmail.com>
+ *      Based on mach-anubis.c by Ben Dooks <ben@simtec.co.uk>
+ *      and modifications by SBZ <sbz@spgui.org> and
+ *      Weibing <http://weibing.blogbus.com> and
+ *      Michel Pollet <buserror@gmail.com>
+ *
+ * For product information, visit http://code.google.com/p/mini2440/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/input.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+#include <linux/dm9000.h>
+#include <linux/i2c/at24.h>
+#include <linux/platform_device.h>
+#include <linux/gpio_keys.h>
+#include <linux/i2c.h>
+#include <linux/mmc/host.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/hardware.h>
+#include <mach/fb.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <mach/regs-gpio.h>
+#include <mach/leds-gpio.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-lcd.h>
+#include <mach/irqs.h>
+#include <plat/nand.h>
+#include <plat/iic.h>
+#include <plat/mci.h>
+#include <plat/udc.h>
+
+#include <plat/regs-serial.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#include <sound/s3c24xx_uda134x.h>
+
+#define MACH_MINI2440_DM9K_BASE (S3C2410_CS4 + 0x300)
+
+static struct map_desc mini2440_iodesc[] __initdata = {
+	/* nothing to declare, move along */
+};
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB
+#define UFCON S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE
+
+
+static struct s3c2410_uartcfg mini2440_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+};
+
+/* USB device UDC support */
+
+static void mini2440_udc_pullup(enum s3c2410_udc_cmd_e cmd)
+{
+	pr_debug("udc: pullup(%d)\n", cmd);
+
+	switch (cmd) {
+		case S3C2410_UDC_P_ENABLE :
+			s3c2410_gpio_setpin(S3C2410_GPC(5), 1);
+			break;
+		case S3C2410_UDC_P_DISABLE :
+			s3c2410_gpio_setpin(S3C2410_GPC(5), 0);
+			break;
+		case S3C2410_UDC_P_RESET :
+			break;
+		default:
+			break;
+	}
+}
+
+static struct s3c2410_udc_mach_info mini2440_udc_cfg __initdata = {
+	.udc_command		= mini2440_udc_pullup,
+};
+
+
+/* LCD timing and setup */
+
+/*
+ * This macro simplifies the table bellow
+ */
+#define _LCD_DECLARE(_clock,_xres,margin_left,margin_right,hsync, \
+			_yres,margin_top,margin_bottom,vsync, refresh) \
+	.width = _xres, \
+	.xres = _xres, \
+	.height = _yres, \
+	.yres = _yres, \
+	.left_margin	= margin_left,	\
+	.right_margin	= margin_right,	\
+	.upper_margin	= margin_top,	\
+	.lower_margin	= margin_bottom,	\
+	.hsync_len	= hsync,	\
+	.vsync_len	= vsync,	\
+	.pixclock	= ((_clock*100000000000LL) /	\
+			   ((refresh) * \
+			   (hsync + margin_left + _xres + margin_right) * \
+			   (vsync + margin_top + _yres + margin_bottom))), \
+	.bpp		= 16,\
+	.type		= (S3C2410_LCDCON1_TFT16BPP |\
+			   S3C2410_LCDCON1_TFT)
+
+struct s3c2410fb_display mini2440_lcd_cfg[] __initdata = {
+	[0] = {	/* mini2440 + 3.5" TFT + touchscreen */
+		_LCD_DECLARE(
+			7,			/* The 3.5 is quite fast */
+			240, 21, 38, 6, 	/* x timing */
+			320, 4, 4, 2,		/* y timing */
+			60),			/* refresh rate */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_INVVLINE |
+				   S3C2410_LCDCON5_INVVFRAME |
+				   S3C2410_LCDCON5_INVVDEN |
+				   S3C2410_LCDCON5_PWREN),
+	},
+	[1] = { /* mini2440 + 7" TFT + touchscreen */
+		_LCD_DECLARE(
+			10,			/* the 7" runs slower */
+			800, 40, 40, 48, 	/* x timing */
+			480, 29, 3, 3,		/* y timing */
+			50),			/* refresh rate */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_INVVLINE |
+				   S3C2410_LCDCON5_INVVFRAME |
+				   S3C2410_LCDCON5_PWREN),
+	},
+	/* The VGA shield can outout at several resolutions. All share 
+	 * the same timings, however, anything smaller than 1024x768
+	 * will only be displayed in the top left corner of a 1024x768
+	 * XGA output unless you add optional dip switches to the shield.
+	 * Therefore timings for other resolutions have been ommited here.
+	 */
+	[2] = {
+		_LCD_DECLARE(
+			10,
+			1024, 1, 2, 2,		/* y timing */
+			768, 200, 16, 16, 	/* x timing */
+			24),	/* refresh rate, maximum stable,
+				 tested with the FPGA shield */
+		.lcdcon5	= (S3C2410_LCDCON5_FRM565 |
+				   S3C2410_LCDCON5_HWSWP),
+	},
+};
+
+/* todo - put into gpio header */
+
+#define S3C2410_GPCCON_MASK(x)	(3 << ((x) * 2))
+#define S3C2410_GPDCON_MASK(x)	(3 << ((x) * 2))
+
+struct s3c2410fb_mach_info mini2440_fb_info __initdata = {
+	.displays	 = &mini2440_lcd_cfg[0], /* not constant! see init */
+	.num_displays	 = 1,
+	.default_display = 0,
+
+	/* Enable VD[2..7], VD[10..15], VD[18..23] and VCLK, syncs, VDEN
+	 * and disable the pull down resistors on pins we are using for LCD
+	 * data. */
+
+	.gpcup		= (0xf << 1) | (0x3f << 10),
+
+	.gpccon		= (S3C2410_GPC1_VCLK   | S3C2410_GPC2_VLINE |
+			   S3C2410_GPC3_VFRAME | S3C2410_GPC4_VM |
+			   S3C2410_GPC10_VD2   | S3C2410_GPC11_VD3 |
+			   S3C2410_GPC12_VD4   | S3C2410_GPC13_VD5 |
+			   S3C2410_GPC14_VD6   | S3C2410_GPC15_VD7),
+
+	.gpccon_mask	= (S3C2410_GPCCON_MASK(1)  | S3C2410_GPCCON_MASK(2)  |
+			   S3C2410_GPCCON_MASK(3)  | S3C2410_GPCCON_MASK(4)  |
+			   S3C2410_GPCCON_MASK(10) | S3C2410_GPCCON_MASK(11) |
+			   S3C2410_GPCCON_MASK(12) | S3C2410_GPCCON_MASK(13) |
+			   S3C2410_GPCCON_MASK(14) | S3C2410_GPCCON_MASK(15)),
+
+	.gpdup		= (0x3f << 2) | (0x3f << 10),
+
+	.gpdcon		= (S3C2410_GPD2_VD10  | S3C2410_GPD3_VD11 |
+			   S3C2410_GPD4_VD12  | S3C2410_GPD5_VD13 |
+			   S3C2410_GPD6_VD14  | S3C2410_GPD7_VD15 |
+			   S3C2410_GPD10_VD18 | S3C2410_GPD11_VD19 |
+			   S3C2410_GPD12_VD20 | S3C2410_GPD13_VD21 |
+			   S3C2410_GPD14_VD22 | S3C2410_GPD15_VD23),
+
+	.gpdcon_mask	= (S3C2410_GPDCON_MASK(2)  | S3C2410_GPDCON_MASK(3) |
+			   S3C2410_GPDCON_MASK(4)  | S3C2410_GPDCON_MASK(5) |
+			   S3C2410_GPDCON_MASK(6)  | S3C2410_GPDCON_MASK(7) |
+			   S3C2410_GPDCON_MASK(10) | S3C2410_GPDCON_MASK(11)|
+			   S3C2410_GPDCON_MASK(12) | S3C2410_GPDCON_MASK(13)|
+			   S3C2410_GPDCON_MASK(14) | S3C2410_GPDCON_MASK(15)),
+};
+
+/* MMC/SD  */
+
+static struct s3c24xx_mci_pdata mini2440_mmc_cfg __initdata = {
+   .gpio_detect   = S3C2410_GPG(8),
+   .gpio_wprotect = S3C2410_GPH(8),
+   .set_power     = NULL,
+   .ocr_avail     = MMC_VDD_32_33|MMC_VDD_33_34,
+};
+
+/* NAND Flash on MINI2440 board */
+
+static struct mtd_partition mini2440_default_nand_part[] __initdata = {
+	[0] = {
+		.name	= "u-boot",
+		.size	= SZ_256K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "u-boot-env",
+		.size	= SZ_128K,
+		.offset	= SZ_256K,
+	},
+	[2] = {
+		.name	= "kernel",
+		/* 5 megabytes, for a kernel with no modules
+		 * or a uImage with a ramdisk attached */
+		.size	= 0x00500000,
+		.offset	= SZ_256K + SZ_128K,
+	},
+	[3] = {
+		.name	= "root",
+		.offset	= SZ_256K + SZ_128K + 0x00500000,
+		.size	= MTDPART_SIZ_FULL,
+	},
+};
+
+static struct s3c2410_nand_set mini2440_nand_sets[] __initdata = {
+	[0] = {
+		.name		= "nand",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(mini2440_default_nand_part),
+		.partitions	= mini2440_default_nand_part,
+	},
+};
+
+static struct s3c2410_platform_nand mini2440_nand_info __initdata = {
+	.tacls		= 0,
+	.twrph0		= 25,
+	.twrph1		= 15,
+	.nr_sets	= ARRAY_SIZE(mini2440_nand_sets),
+	.sets		= mini2440_nand_sets,
+	.ignore_unset_ecc = 1,
+};
+
+/* DM9000AEP 10/100 ethernet controller */
+
+static struct resource mini2440_dm9k_resource[] __initdata = {
+	[0] = {
+		.start = MACH_MINI2440_DM9K_BASE,
+		.end   = MACH_MINI2440_DM9K_BASE + 3,
+		.flags = IORESOURCE_MEM
+	},
+	[1] = {
+		.start = MACH_MINI2440_DM9K_BASE + 4,
+		.end   = MACH_MINI2440_DM9K_BASE + 7,
+		.flags = IORESOURCE_MEM
+	},
+	[2] = {
+		.start = IRQ_EINT7,
+		.end   = IRQ_EINT7,
+		.flags = IORESOURCE_IRQ | IORESOURCE_IRQ_HIGHEDGE,
+	}
+};
+
+/*
+ * The DM9000 has no eeprom, and it's MAC address is set by
+ * the bootloader before starting the kernel.
+ */
+static struct dm9000_plat_data mini2440_dm9k_pdata __initdata = {
+	.flags		= (DM9000_PLATF_16BITONLY | DM9000_PLATF_NO_EEPROM),
+};
+
+static struct platform_device mini2440_device_eth __initdata = {
+	.name		= "dm9000",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(mini2440_dm9k_resource),
+	.resource	= mini2440_dm9k_resource,
+	.dev		= {
+		.platform_data	= &mini2440_dm9k_pdata,
+	},
+};
+
+/*  CON5
+ *	+--+	 /-----\
+ *	|  |    |	|
+ *	|  |	|  BAT	|
+ *	|  |	 \_____/
+ *	|  |
+ *	|  |  +----+  +----+
+ *	|  |  | K5 |  | K1 |
+ *	|  |  +----+  +----+
+ *	|  |  +----+  +----+
+ *	|  |  | K4 |  | K2 |
+ *	|  |  +----+  +----+
+ *	|  |  +----+  +----+
+ *	|  |  | K6 |  | K3 |
+ *	|  |  +----+  +----+
+ *	  .....
+ */
+static struct gpio_keys_button mini2440_buttons[] __initdata = {
+	{
+		.gpio		= S3C2410_GPG(0),		/* K1 */
+		.code		= KEY_F1,
+		.desc		= "Button 1",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(3),		/* K2 */
+		.code		= KEY_F2,
+		.desc		= "Button 2",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(5),		/* K3 */
+		.code		= KEY_F3,
+		.desc		= "Button 3",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(6),		/* K4 */
+		.code		= KEY_POWER,
+		.desc		= "Power",
+		.active_low	= 1,
+	},
+	{
+		.gpio		= S3C2410_GPG(7),		/* K5 */
+		.code		= KEY_F5,
+		.desc		= "Button 5",
+		.active_low	= 1,
+	},
+#if 0
+	/* this pin is also known as TCLK1 and seems to already
+	 * marked as "in use" somehow in the kernel -- possibly wrongly */
+	{
+		.gpio		= S3C2410_GPG(11),	/* K6 */
+		.code		= KEY_F6,
+		.desc		= "Button 6",
+		.active_low	= 1,
+	},
+#endif
+};
+
+static struct gpio_keys_platform_data mini2440_button_data __initdata = {
+	.buttons	= mini2440_buttons,
+	.nbuttons	= ARRAY_SIZE(mini2440_buttons),
+};
+
+static struct platform_device mini2440_button_device __initdata = {
+	.name		= "gpio-keys",
+	.id		= -1,
+	.dev		= {
+		.platform_data	= &mini2440_button_data,
+	}
+};
+
+/* LEDS */
+
+static struct s3c24xx_led_platdata mini2440_led1_pdata __initdata = {
+	.name		= "led1",
+	.gpio		= S3C2410_GPB(5),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "heartbeat",
+};
+
+static struct s3c24xx_led_platdata mini2440_led2_pdata __initdata = {
+	.name		= "led2",
+	.gpio		= S3C2410_GPB(6),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "nand-disk",
+};
+
+static struct s3c24xx_led_platdata mini2440_led3_pdata __initdata = {
+	.name		= "led3",
+	.gpio		= S3C2410_GPB(7),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "mmc0",
+};
+
+static struct s3c24xx_led_platdata mini2440_led4_pdata __initdata = {
+	.name		= "led4",
+	.gpio		= S3C2410_GPB(8),
+	.flags		= S3C24XX_LEDF_ACTLOW | S3C24XX_LEDF_TRISTATE,
+	.def_trigger	= "",
+};
+
+static struct s3c24xx_led_platdata mini2440_led_backlight_pdata __initdata = {
+	.name		= "backlight",
+	.gpio		= S3C2410_GPG(4),
+	.def_trigger	= "backlight",
+};
+
+static struct platform_device mini2440_led1 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 1,
+	.dev		= {
+		.platform_data	= &mini2440_led1_pdata,
+	},
+};
+
+static struct platform_device mini2440_led2 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 2,
+	.dev		= {
+		.platform_data	= &mini2440_led2_pdata,
+	},
+};
+
+static struct platform_device mini2440_led3 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 3,
+	.dev		= {
+		.platform_data	= &mini2440_led3_pdata,
+	},
+};
+
+static struct platform_device mini2440_led4 __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 4,
+	.dev		= {
+		.platform_data	= &mini2440_led4_pdata,
+	},
+};
+
+static struct platform_device mini2440_led_backlight __initdata = {
+	.name		= "s3c24xx_led",
+	.id		= 5,
+	.dev		= {
+		.platform_data	= &mini2440_led_backlight_pdata,
+	},
+};
+
+/* AUDIO */
+
+static struct s3c24xx_uda134x_platform_data mini2440_audio_pins __initdata = {
+	.l3_clk = S3C2410_GPB(4),
+	.l3_mode = S3C2410_GPB(2),
+	.l3_data = S3C2410_GPB(3),
+	.model = UDA134X_UDA1341
+};
+
+static struct platform_device mini2440_audio __initdata = {
+	.name		= "s3c24xx_uda134x",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &mini2440_audio_pins,
+	},
+};
+
+/*
+ * I2C devices
+ */
+static struct at24_platform_data at24c08 = {
+	.byte_len	= SZ_8K / 8,
+	.page_size	= 16,
+};
+
+static struct i2c_board_info mini2440_i2c_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("24c08", 0x50),
+		.platform_data = &at24c08,
+	},
+};
+
+static struct platform_device *mini2440_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_wdt,
+/*	&s3c_device_adc,*/ /* ADC doesn't like living with touchscreen ! */
+	&s3c_device_i2c0,
+	&s3c_device_rtc,
+	&s3c_device_usbgadget,
+	&mini2440_device_eth,
+	&mini2440_led1,
+	&mini2440_led2,
+	&mini2440_led3,
+	&mini2440_led4,
+	&mini2440_button_device,
+	&s3c_device_nand,
+	&s3c_device_sdi,
+	&s3c_device_iis,
+	&mini2440_audio,
+/*	&s3c_device_timer[0],*/	/* buzzer pwm, no API for it */
+	/* remaining devices are optional */
+};
+
+static void __init mini2440_map_io(void)
+{
+	s3c24xx_init_io(mini2440_iodesc, ARRAY_SIZE(mini2440_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(mini2440_uartcfgs, ARRAY_SIZE(mini2440_uartcfgs));
+
+	s3c_device_nand.dev.platform_data = &mini2440_nand_info;
+	s3c_device_sdi.dev.platform_data = &mini2440_mmc_cfg;
+}
+
+/*
+ * mini2440_features string
+ *
+ * t = Touchscreen present
+ * b = backlight control
+ * c = camera [TODO]
+ * 0-9 LCD configuration
+ *
+ */
+static char mini2440_features_str[12] __initdata = "0tb";
+
+static int __init mini2440_features_setup(char *str)
+{
+	if (str)
+		strlcpy(mini2440_features_str, str, sizeof(mini2440_features_str));
+	return 1;
+}
+
+__setup("mini2440=", mini2440_features_setup);
+
+#define FEATURE_SCREEN (1 << 0)
+#define FEATURE_BACKLIGHT (1 << 1)
+#define FEATURE_TOUCH (1 << 2)
+#define FEATURE_CAMERA (1 << 3)
+
+struct mini2440_features_t {
+	int count;
+	int done;
+	int lcd_index;
+	struct platform_device *optional[8];
+};
+
+static void mini2440_parse_features(
+		struct mini2440_features_t * features,
+		const char * features_str )
+{
+	const char * fp = features_str;
+
+	features->count = 0;
+	features->done = 0;
+	features->lcd_index = -1;
+
+	while (*fp) {
+		char f = *fp++;
+
+		switch (f) {
+		case '0'...'9':	/* tft screen */
+			if (features->done & FEATURE_SCREEN) {
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"screen type already set\n", f);
+			} else {
+				int li = f - '0';
+				if (li >= ARRAY_SIZE(mini2440_lcd_cfg))
+					printk(KERN_INFO "MINI2440: "
+						"'%c' out of range LCD mode\n", f);
+				else {
+					features->optional[features->count++] =
+							&s3c_device_lcd;
+					features->lcd_index = li;
+				}
+			}
+			features->done |= FEATURE_SCREEN;
+			break;
+		case 'b':
+			if (features->done & FEATURE_BACKLIGHT)
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"backlight already set\n", f);
+			else {
+				features->optional[features->count++] =
+						&mini2440_led_backlight;
+			}
+			features->done |= FEATURE_BACKLIGHT;
+			break;
+		case 't':
+			printk(KERN_INFO "MINI2440: '%c' ignored, "
+				"touchscreen not compiled in\n", f);
+			break;
+		case 'c':
+			if (features->done & FEATURE_CAMERA)
+				printk(KERN_INFO "MINI2440: '%c' ignored, "
+					"camera already registered\n", f);
+			else
+				features->optional[features->count++] =
+					&s3c_device_camif;
+			features->done |= FEATURE_CAMERA;
+			break;
+		}
+	}
+}
+
+static void __init mini2440_init(void)
+{
+	struct mini2440_features_t features = { 0 };
+	int i;
+
+	printk(KERN_INFO "MINI2440: Option string mini2440=%s\n",
+			mini2440_features_str);
+
+	/* Parse the feature string */
+	mini2440_parse_features(&features, mini2440_features_str);
+
+	/* turn LCD on */
+	s3c2410_gpio_cfgpin(S3C2410_GPC(0), S3C2410_GPC0_LEND);
+
+	/* Turn the backlight early on */
+	s3c2410_gpio_setpin(S3C2410_GPG(4), 1);
+	s3c2410_gpio_cfgpin(S3C2410_GPG(4), S3C2410_GPIO_OUTPUT);
+
+	/* remove pullup on optional PWM backlight -- unused on 3.5 and 7"s */
+	s3c2410_gpio_pullup(S3C2410_GPB(1), 0);
+	s3c2410_gpio_setpin(S3C2410_GPB(1), 0);
+	s3c2410_gpio_cfgpin(S3C2410_GPB(1), S3C2410_GPIO_INPUT);
+
+	/* Make sure the D+ pullup pin is output */
+	s3c2410_gpio_cfgpin(S3C2410_GPC(5), S3C2410_GPIO_OUTPUT);
+
+	/* mark the key as input, without pullups (there is one on the board) */
+	for (i = 0; i < ARRAY_SIZE(mini2440_buttons); i++) {
+		s3c2410_gpio_pullup(mini2440_buttons[i].gpio, 0);
+		s3c2410_gpio_cfgpin(mini2440_buttons[i].gpio,
+					S3C2410_GPIO_INPUT);
+	}
+	if (features.lcd_index != -1) {
+		int li;
+
+		mini2440_fb_info.displays =
+			&mini2440_lcd_cfg[features.lcd_index];
+
+		printk(KERN_INFO "MINI2440: LCD");
+		for (li = 0; li < ARRAY_SIZE(mini2440_lcd_cfg); li++)
+			if (li == features.lcd_index)
+				printk(" [%d:%dx%d]", li,
+					mini2440_lcd_cfg[li].width,
+					mini2440_lcd_cfg[li].height);
+			else
+				printk(" %d:%dx%d", li,
+					mini2440_lcd_cfg[li].width,
+					mini2440_lcd_cfg[li].height);
+		printk("\n");
+		s3c24xx_fb_set_platdata(&mini2440_fb_info);
+	}
+	s3c24xx_udc_set_platdata(&mini2440_udc_cfg);
+	s3c_i2c0_set_platdata(NULL);
+	i2c_register_board_info(0, mini2440_i2c_devs,
+				ARRAY_SIZE(mini2440_i2c_devs));
+
+	platform_add_devices(mini2440_devices, ARRAY_SIZE(mini2440_devices));
+
+	if (features.count)	/* the optional features */
+		platform_add_devices(features.optional, features.count);
+
+}
+
+
+MACHINE_START(MINI2440, "MINI2440")
+	/* Maintainer: Michel Pollet <buserror@gmail.com> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= mini2440_map_io,
+	.init_machine	= mini2440_init,
+	.init_irq	= s3c24xx_init_irq,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c2442/Kconfig

@@ -24,6 +24,18 @@ config SMDK2440_CPU2442
 	depends on ARCH_S3C2440
 	select CPU_S3C2442
 
+config MACH_NEO1973_GTA02
+	bool "Openmoko GTA02 / Freerunner phone"
+	select CPU_S3C2442
+	select MFD_PCF50633
+	select PCF50633_GPIO
+	select I2C
+	select POWER_SUPPLY
+	select MACH_NEO1973
+	select S3C2410_PWM
+	help
+	   Say Y here if you are using the Openmoko GTA02 / Freerunner GSM Phone
+
 
 endmenu
 

arch/arm/mach-s3c2442/Makefile

@@ -12,5 +12,7 @@ obj-				:=
 obj-$(CONFIG_CPU_S3C2442)	+= s3c2442.o
 obj-$(CONFIG_CPU_S3C2442)	+= clock.o
 
+obj-$(CONFIG_MACH_NEO1973_GTA02) += mach-gta02.o
+
 # Machine support
 

arch/arm/mach-s3c2442/include/mach/gta02.h

+#ifndef _GTA02_H
+#define _GTA02_H
+
+#include <mach/regs-gpio.h>
+
+/* Different hardware revisions, passed in ATAG_REVISION by u-boot */
+#define GTA02v1_SYSTEM_REV	0x00000310
+#define GTA02v2_SYSTEM_REV	0x00000320
+#define GTA02v3_SYSTEM_REV	0x00000330
+#define GTA02v4_SYSTEM_REV	0x00000340
+#define GTA02v5_SYSTEM_REV	0x00000350
+/* since A7 is basically same as A6, we use A6 PCB ID */
+#define GTA02v6_SYSTEM_REV	0x00000360
+
+#define GTA02_GPIO_n3DL_GSM	S3C2410_GPA(13)	/* v1 + v2 + v3 only */
+
+#define GTA02_GPIO_PWR_LED1	S3C2410_GPB(0)
+#define GTA02_GPIO_PWR_LED2	S3C2410_GPB(1)
+#define GTA02_GPIO_AUX_LED	S3C2410_GPB(2)
+#define GTA02_GPIO_VIBRATOR_ON	S3C2410_GPB(3)
+#define GTA02_GPIO_MODEM_RST	S3C2410_GPB(5)
+#define GTA02_GPIO_BT_EN	S3C2410_GPB(6)
+#define GTA02_GPIO_MODEM_ON	S3C2410_GPB(7)
+#define GTA02_GPIO_EXTINT8	S3C2410_GPB(8)
+#define GTA02_GPIO_USB_PULLUP	S3C2410_GPB(9)
+
+#define GTA02_GPIO_PIO5		S3C2410_GPC(5)	/* v3 + v4 only */
+
+#define GTA02v3_GPIO_nG1_CS	S3C2410_GPD(12)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nG2_CS	S3C2410_GPD(13)	/* v3 + v4 only */
+#define GTA02v5_GPIO_HDQ	S3C2410_GPD(14)   /* v5 + */
+
+#define GTA02_GPIO_nG1_INT	S3C2410_GPF(0)
+#define GTA02_GPIO_IO1		S3C2410_GPF(1)
+#define GTA02_GPIO_PIO_2	S3C2410_GPF(2)	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_JACK_INSERT	S3C2410_GPF(4)
+#define GTA02_GPIO_WLAN_GPIO1	S3C2410_GPF(5)	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_AUX_KEY	S3C2410_GPF(6)
+#define GTA02_GPIO_HOLD_KEY	S3C2410_GPF(7)
+
+#define GTA02_GPIO_3D_IRQ	S3C2410_GPG(4)
+#define GTA02v2_GPIO_nG2_INT	S3C2410_GPG(8)	/* v2 + v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_OC	S3C2410_GPG(9)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nUSB_FLT	S3C2410_GPG(10)	/* v3 + v4 only */
+#define GTA02v3_GPIO_nGSM_OC	S3C2410_GPG(11)	/* v3 + v4 only */
+
+#define GTA02_GPIO_AMP_SHUT	S3C2440_GPJ1	/* v2 + v3 + v4 only */
+#define GTA02v1_GPIO_WLAN_GPIO10	S3C2440_GPJ2
+#define GTA02_GPIO_HP_IN	S3C2440_GPJ2	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_INT0		S3C2440_GPJ3	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_nGSM_EN	S3C2440_GPJ4
+#define GTA02_GPIO_3D_RESET	S3C2440_GPJ5
+#define GTA02_GPIO_nDL_GSM	S3C2440_GPJ6	/* v4 + v5 only */
+#define GTA02_GPIO_WLAN_GPIO0	S3C2440_GPJ7
+#define GTA02v1_GPIO_BAT_ID	S3C2440_GPJ8
+#define GTA02_GPIO_KEEPACT	S3C2440_GPJ8
+#define GTA02v1_GPIO_HP_IN	S3C2440_GPJ10
+#define GTA02_CHIP_PWD		S3C2440_GPJ11	/* v2 + v3 + v4 only */
+#define GTA02_GPIO_nWLAN_RESET	S3C2440_GPJ12	/* v2 + v3 + v4 only */
+
+#define GTA02_IRQ_GSENSOR_1	IRQ_EINT0
+#define GTA02_IRQ_MODEM		IRQ_EINT1
+#define GTA02_IRQ_PIO_2		IRQ_EINT2	/* v2 + v3 + v4 only */
+#define GTA02_IRQ_nJACK_INSERT	IRQ_EINT4
+#define GTA02_IRQ_WLAN_GPIO1	IRQ_EINT5
+#define GTA02_IRQ_AUX		IRQ_EINT6
+#define GTA02_IRQ_nHOLD		IRQ_EINT7
+#define GTA02_IRQ_PCF50633	IRQ_EINT9
+#define GTA02_IRQ_3D		IRQ_EINT12
+#define GTA02_IRQ_GSENSOR_2	IRQ_EINT16	/* v2 + v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_OC	IRQ_EINT17	/* v3 + v4 only */
+#define GTA02v3_IRQ_nUSB_FLT	IRQ_EINT18	/* v3 + v4 only */
+#define GTA02v3_IRQ_nGSM_OC	IRQ_EINT19	/* v3 + v4 only */
+
+/* returns 00 000 on GTA02 A5 and earlier, A6 returns 01 001 */
+#define GTA02_PCB_ID1_0		S3C2410_GPC(13)
+#define GTA02_PCB_ID1_1		S3C2410_GPC(15)
+#define GTA02_PCB_ID1_2		S3C2410_GPD(0)
+#define GTA02_PCB_ID2_0		S3C2410_GPD(3)
+#define GTA02_PCB_ID2_1		S3C2410_GPD(4)
+
+int gta02_get_pcb_revision(void);
+
+#endif /* _GTA02_H */

arch/arm/mach-s3c2442/mach-gta02.c

+/*
+ * linux/arch/arm/mach-s3c2442/mach-gta02.c
+ *
+ * S3C2442 Machine Support for Openmoko GTA02 / FreeRunner.
+ *
+ * Copyright (C) 2006-2009 by Openmoko, Inc.
+ * Authors: Harald Welte <laforge@openmoko.org>
+ *          Andy Green <andy@openmoko.org>
+ *          Werner Almesberger <werner@openmoko.org>
+ * All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/delay.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/workqueue.h>
+#include <linux/platform_device.h>
+#include <linux/serial_core.h>
+#include <linux/spi/spi.h>
+
+#include <linux/mmc/host.h>
+
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/nand.h>
+#include <linux/mtd/nand_ecc.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mtd/physmap.h>
+#include <linux/io.h>
+
+#include <linux/i2c.h>
+#include <linux/backlight.h>
+#include <linux/regulator/machine.h>
+
+#include <linux/mfd/pcf50633/core.h>
+#include <linux/mfd/pcf50633/mbc.h>
+#include <linux/mfd/pcf50633/adc.h>
+#include <linux/mfd/pcf50633/gpio.h>
+#include <linux/mfd/pcf50633/pmic.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <mach/regs-irq.h>
+#include <mach/regs-gpio.h>
+#include <mach/regs-gpioj.h>
+#include <mach/fb.h>
+
+#include <mach/spi.h>
+#include <mach/spi-gpio.h>
+#include <plat/usb-control.h>
+#include <mach/regs-mem.h>
+#include <mach/hardware.h>
+
+#include <mach/gta02.h>
+
+#include <plat/regs-serial.h>
+#include <plat/nand.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/pm.h>
+#include <plat/udc.h>
+#include <plat/gpio-cfg.h>
+#include <plat/iic.h>
+
+static struct pcf50633 *gta02_pcf;
+
+/*
+ * This gets called every 1ms when we paniced.
+ */
+
+static long gta02_panic_blink(long count)
+{
+	long delay = 0;
+	static long last_blink;
+	static char led;
+
+	/* Fast blink: 200ms period. */
+	if (count - last_blink < 100)
+		return 0;
+
+	led ^= 1;
+	gpio_direction_output(GTA02_GPIO_AUX_LED, led);
+
+	last_blink = count;
+
+	return delay;
+}
+
+
+static struct map_desc gta02_iodesc[] __initdata = {
+	{
+		.virtual	= 0xe0000000,
+		.pfn		= __phys_to_pfn(S3C2410_CS3 + 0x01000000),
+		.length		= SZ_1M,
+		.type		= MT_DEVICE
+	},
+};
+
+#define UCON (S3C2410_UCON_DEFAULT | S3C2443_UCON_RXERR_IRQEN)
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
+#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
+
+static struct s3c2410_uartcfg gta02_uartcfgs[] = {
+	[0] = {
+		.hwport		= 0,
+		.flags		= 0,
+		.ucon		= UCON,
+		.ulcon		= ULCON,
+		.ufcon		= UFCON,
+	},
+	[1] = {
+		.hwport		= 1,
+		.flags		= 0,
+		.ucon		= UCON,
+		.ulcon		= ULCON,
+		.ufcon		= UFCON,
+	},
+	[2] = {
+		.hwport		= 2,
+		.flags		= 0,
+		.ucon		= UCON,
+		.ulcon		= ULCON,
+		.ufcon		= UFCON,
+	},
+};
+
+#ifdef CONFIG_CHARGER_PCF50633
+/*
+ * On GTA02 the 1A charger features a 48K resistor to 0V on the ID pin.
+ * We use this to recognize that we can pull 1A from the USB socket.
+ *
+ * These constants are the measured pcf50633 ADC levels with the 1A
+ * charger / 48K resistor, and with no pulldown resistor.
+ */
+
+#define ADC_NOM_CHG_DETECT_1A 6
+#define ADC_NOM_CHG_DETECT_USB 43
+
+static void
+gta02_configure_pmu_for_charger(struct pcf50633 *pcf, void *unused, int res)
+{
+	int  ma;
+
+	/* Interpret charger type */
+	if (res < ((ADC_NOM_CHG_DETECT_USB + ADC_NOM_CHG_DETECT_1A) / 2)) {
+
+		/*
+		 * Sanity - stop GPO driving out now that we have a 1A charger
+		 * GPO controls USB Host power generation on GTA02
+		 */
+		pcf50633_gpio_set(pcf, PCF50633_GPO, 0);
+
+		ma = 1000;
+	} else
+		ma = 100;
+
+	pcf50633_mbc_usb_curlim_set(pcf, ma);
+}
+
+static struct delayed_work gta02_charger_work;
+static int gta02_usb_vbus_draw;
+
+static void gta02_charger_worker(struct work_struct *work)
+{
+	if (gta02_usb_vbus_draw) {
+		pcf50633_mbc_usb_curlim_set(gta02_pcf, gta02_usb_vbus_draw);
+		return;
+	}
+
+#ifdef CONFIG_PCF50633_ADC
+	pcf50633_adc_async_read(gta02_pcf,
+				PCF50633_ADCC1_MUX_ADCIN1,
+				PCF50633_ADCC1_AVERAGE_16,
+				gta02_configure_pmu_for_charger,
+				NULL);
+#else
+	/*
+	 * If the PCF50633 ADC is disabled we fallback to a
+	 * 100mA limit for safety.
+	 */
+	pcf50633_mbc_usb_curlim_set(pcf, 100);
+#endif
+}
+
+#define GTA02_CHARGER_CONFIGURE_TIMEOUT ((3000 * HZ) / 1000)
+
+static void gta02_pmu_event_callback(struct pcf50633 *pcf, int irq)
+{
+	if (irq == PCF50633_IRQ_USBINS) {
+		schedule_delayed_work(&gta02_charger_work,
+				      GTA02_CHARGER_CONFIGURE_TIMEOUT);
+
+		return;
+	}
+
+	if (irq == PCF50633_IRQ_USBREM) {
+		cancel_delayed_work_sync(&gta02_charger_work);
+		gta02_usb_vbus_draw = 0;
+	}
+}
+
+static void gta02_udc_vbus_draw(unsigned int ma)
+{
+	if (!gta02_pcf)
+		return;
+
+	gta02_usb_vbus_draw = ma;
+
+	schedule_delayed_work(&gta02_charger_work,
+			      GTA02_CHARGER_CONFIGURE_TIMEOUT);
+}
+#else /* !CONFIG_CHARGER_PCF50633 */
+#define gta02_pmu_event_callback	NULL
+#define gta02_udc_vbus_draw		NULL
+#endif
+
+/*
+ * This is called when pc50633 is probed, unfortunately quite late in the
+ * day since it is an I2C bus device. Here we can belatedly define some
+ * platform devices with the advantage that we can mark the pcf50633 as the
+ * parent. This makes them get suspended and resumed with their parent
+ * the pcf50633 still around.
+ */
+
+static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf);
+
+
+static char *gta02_batteries[] = {
+	"battery",
+};
+
+struct pcf50633_platform_data gta02_pcf_pdata = {
+	.resumers = {
+		[0] =	PCF50633_INT1_USBINS |
+			PCF50633_INT1_USBREM |
+			PCF50633_INT1_ALARM,
+		[1] =	PCF50633_INT2_ONKEYF,
+		[2] =	PCF50633_INT3_ONKEY1S,
+		[3] =	PCF50633_INT4_LOWSYS |
+			PCF50633_INT4_LOWBAT |
+			PCF50633_INT4_HIGHTMP,
+	},
+
+	.batteries = gta02_batteries,
+	.num_batteries = ARRAY_SIZE(gta02_batteries),
+	.reg_init_data = {
+		[PCF50633_REGULATOR_AUTO] = {
+			.constraints = {
+				.min_uV = 3300000,
+				.max_uV = 3300000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.always_on = 1,
+				.apply_uV = 1,
+				.state_mem = {
+					.enabled = 1,
+				},
+			},
+		},
+		[PCF50633_REGULATOR_DOWN1] = {
+			.constraints = {
+				.min_uV = 1300000,
+				.max_uV = 1600000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.always_on = 1,
+				.apply_uV = 1,
+			},
+		},
+		[PCF50633_REGULATOR_DOWN2] = {
+			.constraints = {
+				.min_uV = 1800000,
+				.max_uV = 1800000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+				.always_on = 1,
+				.state_mem = {
+					.enabled = 1,
+				},
+			},
+		},
+		[PCF50633_REGULATOR_HCLDO] = {
+			.constraints = {
+				.min_uV = 2000000,
+				.max_uV = 3300000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
+				.always_on = 1,
+			},
+		},
+		[PCF50633_REGULATOR_LDO1] = {
+			.constraints = {
+				.min_uV = 3300000,
+				.max_uV = 3300000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+				.state_mem = {
+					.enabled = 0,
+				},
+			},
+		},
+		[PCF50633_REGULATOR_LDO2] = {
+			.constraints = {
+				.min_uV = 3300000,
+				.max_uV = 3300000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+			},
+		},
+		[PCF50633_REGULATOR_LDO3] = {
+			.constraints = {
+				.min_uV = 3000000,
+				.max_uV = 3000000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+			},
+		},
+		[PCF50633_REGULATOR_LDO4] = {
+			.constraints = {
+				.min_uV = 3200000,
+				.max_uV = 3200000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+			},
+		},
+		[PCF50633_REGULATOR_LDO5] = {
+			.constraints = {
+				.min_uV = 3000000,
+				.max_uV = 3000000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.apply_uV = 1,
+				.state_mem = {
+					.enabled = 1,
+				},
+			},
+		},
+		[PCF50633_REGULATOR_LDO6] = {
+			.constraints = {
+				.min_uV = 3000000,
+				.max_uV = 3000000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+			},
+		},
+		[PCF50633_REGULATOR_MEMLDO] = {
+			.constraints = {
+				.min_uV = 1800000,
+				.max_uV = 1800000,
+				.valid_modes_mask = REGULATOR_MODE_NORMAL,
+				.state_mem = {
+					.enabled = 1,
+				},
+			},
+		},
+
+	},
+	.probe_done = gta02_pmu_attach_child_devices,
+	.mbc_event_callback = gta02_pmu_event_callback,
+};
+
+
+/* NOR Flash. */
+
+#define GTA02_FLASH_BASE	0x18000000 /* GCS3 */
+#define GTA02_FLASH_SIZE	0x200000 /* 2MBytes */
+
+static struct physmap_flash_data gta02_nor_flash_data = {
+	.width		= 2,
+};
+
+static struct resource gta02_nor_flash_resource = {
+	.start		= GTA02_FLASH_BASE,
+	.end		= GTA02_FLASH_BASE + GTA02_FLASH_SIZE - 1,
+	.flags		= IORESOURCE_MEM,
+};
+
+static struct platform_device gta02_nor_flash = {
+	.name		= "physmap-flash",
+	.id		= 0,
+	.dev		= {
+		.platform_data	= &gta02_nor_flash_data,
+	},
+	.resource	= &gta02_nor_flash_resource,
+	.num_resources	= 1,
+};
+
+
+struct platform_device s3c24xx_pwm_device = {
+	.name		= "s3c24xx_pwm",
+	.num_resources	= 0,
+};
+
+static struct i2c_board_info gta02_i2c_devs[] __initdata = {
+	{
+		I2C_BOARD_INFO("pcf50633", 0x73),
+		.irq = GTA02_IRQ_PCF50633,
+		.platform_data = &gta02_pcf_pdata,
+	},
+	{
+		I2C_BOARD_INFO("wm8753", 0x1a),
+	},
+};
+
+static struct s3c2410_nand_set gta02_nand_sets[] = {
+	[0] = {
+		/*
+		 * This name is also hard-coded in the boot loaders, so
+		 * changing it would would require all users to upgrade
+		 * their boot loaders, some of which are stored in a NOR
+		 * that is considered to be immutable.
+		 */
+		.name		= "neo1973-nand",
+		.nr_chips	= 1,
+		.use_bbt	= 1,
+		.force_soft_ecc	= 1,
+	},
+};
+
+/*
+ * Choose a set of timings derived from S3C@2442B MCP54
+ * data sheet (K5D2G13ACM-D075 MCP Memory).
+ */
+
+static struct s3c2410_platform_nand gta02_nand_info = {
+	.tacls		= 0,
+	.twrph0		= 25,
+	.twrph1		= 15,
+	.nr_sets	= ARRAY_SIZE(gta02_nand_sets),
+	.sets		= gta02_nand_sets,
+};
+
+
+static void gta02_udc_command(enum s3c2410_udc_cmd_e cmd)
+{
+	switch (cmd) {
+	case S3C2410_UDC_P_ENABLE:
+		pr_debug("%s S3C2410_UDC_P_ENABLE\n", __func__);
+		gpio_direction_output(GTA02_GPIO_USB_PULLUP, 1);
+		break;
+	case S3C2410_UDC_P_DISABLE:
+		pr_debug("%s S3C2410_UDC_P_DISABLE\n", __func__);
+		gpio_direction_output(GTA02_GPIO_USB_PULLUP, 0);
+		break;
+	case S3C2410_UDC_P_RESET:
+		pr_debug("%s S3C2410_UDC_P_RESET\n", __func__);
+		/* FIXME: Do something here. */
+	}
+}
+
+/* Get PMU to set USB current limit accordingly. */
+static struct s3c2410_udc_mach_info gta02_udc_cfg = {
+	.vbus_draw	= gta02_udc_vbus_draw,
+	.udc_command	= gta02_udc_command,
+
+};
+
+
+
+static void gta02_bl_set_intensity(int intensity)
+{
+	struct pcf50633 *pcf = gta02_pcf;
+	int old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT);
+
+	/* We map 8-bit intensity to 6-bit intensity in hardware. */
+	intensity >>= 2;
+
+	/*
+	 * This can happen during, eg, print of panic on blanked console,
+	 * but we can't service i2c without interrupts active, so abort.
+	 */
+	if (in_atomic()) {
+		printk(KERN_ERR "gta02_bl_set_intensity called while atomic\n");
+		return;
+	}
+
+	old_intensity = pcf50633_reg_read(pcf, PCF50633_REG_LEDOUT);
+	if (intensity == old_intensity)
+		return;
+
+	/* We can't do this anywhere else. */
+	pcf50633_reg_write(pcf, PCF50633_REG_LEDDIM, 5);
+
+	if (!(pcf50633_reg_read(pcf, PCF50633_REG_LEDENA) & 3))
+		old_intensity = 0;
+
+	/*
+	 * The PCF50633 cannot handle LEDOUT = 0 (datasheet p60)
+	 * if seen, you have to re-enable the LED unit.
+	 */
+	if (!intensity || !old_intensity)
+		pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 0);
+
+	/* Illegal to set LEDOUT to 0. */
+	if (!intensity)
+		pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f, 2);
+	else
+		pcf50633_reg_set_bit_mask(pcf, PCF50633_REG_LEDOUT, 0x3f,
+					  intensity);
+
+	if (intensity)
+		pcf50633_reg_write(pcf, PCF50633_REG_LEDENA, 2);
+
+}
+
+static struct generic_bl_info gta02_bl_info = {
+	.name			= "gta02-bl",
+	.max_intensity		= 0xff,
+	.default_intensity	= 0xff,
+	.set_bl_intensity	= gta02_bl_set_intensity,
+};
+
+static struct platform_device gta02_bl_dev = {
+	.name			= "generic-bl",
+	.id			= 1,
+	.dev = {
+		.platform_data = &gta02_bl_info,
+	},
+};
+
+
+
+/* USB */
+static struct s3c2410_hcd_info gta02_usb_info = {
+	.port[0]	= {
+		.flags	= S3C_HCDFLG_USED,
+	},
+	.port[1]	= {
+		.flags	= 0,
+	},
+};
+
+
+static void __init gta02_map_io(void)
+{
+	s3c24xx_init_io(gta02_iodesc, ARRAY_SIZE(gta02_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(gta02_uartcfgs, ARRAY_SIZE(gta02_uartcfgs));
+}
+
+
+/* These are the guys that don't need to be children of PMU. */
+
+static struct platform_device *gta02_devices[] __initdata = {
+	&s3c_device_usb,
+	&s3c_device_wdt,
+	&s3c_device_sdi,
+	&s3c_device_usbgadget,
+	&s3c_device_nand,
+	&gta02_nor_flash,
+	&s3c24xx_pwm_device,
+	&s3c_device_iis,
+	&s3c_device_i2c0,
+};
+
+/* These guys DO need to be children of PMU. */
+
+static struct platform_device *gta02_devices_pmu_children[] = {
+	&gta02_bl_dev,
+};
+
+
+/*
+ * This is called when pc50633 is probed, quite late in the day since it is an
+ * I2C bus device.  Here we can define platform devices with the advantage that
+ * we can mark the pcf50633 as the parent.  This makes them get suspended and
+ * resumed with their parent the pcf50633 still around.  All devices whose
+ * operation depends on something from pcf50633 must have this relationship
+ * made explicit like this, or suspend and resume will become an unreliable
+ * hellworld.
+ */
+
+static void gta02_pmu_attach_child_devices(struct pcf50633 *pcf)
+{
+	int n;
+
+	/* Grab a copy of the now probed PMU pointer. */
+	gta02_pcf = pcf;
+
+	for (n = 0; n < ARRAY_SIZE(gta02_devices_pmu_children); n++)
+		gta02_devices_pmu_children[n]->dev.parent = pcf->dev;
+
+	platform_add_devices(gta02_devices_pmu_children,
+			     ARRAY_SIZE(gta02_devices_pmu_children));
+}
+
+static void gta02_poweroff(void)
+{
+	pcf50633_reg_set_bit_mask(gta02_pcf, PCF50633_REG_OOCSHDWN, 1, 1);
+}
+
+static void __init gta02_machine_init(void)
+{
+	/* Set the panic callback to make AUX LED blink at ~5Hz. */
+	panic_blink = gta02_panic_blink;
+
+	s3c_pm_init();
+
+#ifdef CONFIG_CHARGER_PCF50633
+	INIT_DELAYED_WORK(&gta02_charger_work, gta02_charger_worker);
+#endif
+
+	s3c_device_usb.dev.platform_data = &gta02_usb_info;
+	s3c_device_nand.dev.platform_data = &gta02_nand_info;
+
+	s3c24xx_udc_set_platdata(&gta02_udc_cfg);
+	s3c_i2c0_set_platdata(NULL);
+
+	i2c_register_board_info(0, gta02_i2c_devs, ARRAY_SIZE(gta02_i2c_devs));
+
+	platform_add_devices(gta02_devices, ARRAY_SIZE(gta02_devices));
+	pm_power_off = gta02_poweroff;
+}
+
+
+MACHINE_START(NEO1973_GTA02, "GTA02")
+	/* Maintainer: Nelson Castillo <arhuaco@freaks-unidos.net> */
+	.phys_io	= S3C2410_PA_UART,
+	.io_pg_offst	= (((u32)S3C24XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C2410_SDRAM_PA + 0x100,
+	.map_io		= gta02_map_io,
+	.init_irq	= s3c24xx_init_irq,
+	.init_machine	= gta02_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mm/alignment.c

@@ -62,6 +62,12 @@
 #define SHIFT_ASR	0x40
 #define SHIFT_RORRRX	0x60
 
+#define BAD_INSTR 	0xdeadc0de
+
+/* Thumb-2 32 bit format per ARMv7 DDI0406A A6.3, either f800h,e800h,f800h */
+#define IS_T32(hi16) \
+	(((hi16) & 0xe000) == 0xe000 && ((hi16) & 0x1800))
+
 static unsigned long ai_user;
 static unsigned long ai_sys;
 static unsigned long ai_skipped;
@@ -332,38 +338,48 @@ do_alignment_ldrdstrd(unsigned long addr, unsigned long instr,
 		      struct pt_regs *regs)
 {
 	unsigned int rd = RD_BITS(instr);
-
-	if (((rd & 1) == 1) || (rd == 14))
+	unsigned int rd2;
+	int load;
+
+	if ((instr & 0xfe000000) == 0xe8000000) {
+		/* ARMv7 Thumb-2 32-bit LDRD/STRD */
+		rd2 = (instr >> 8) & 0xf;
+		load = !!(LDST_L_BIT(instr));
+	} else if (((rd & 1) == 1) || (rd == 14))
 		goto bad;
+	else {
+		load = ((instr & 0xf0) == 0xd0);
+		rd2 = rd + 1;
+	}
 
 	ai_dword += 1;
 
 	if (user_mode(regs))
 		goto user;
 
-	if ((instr & 0xf0) == 0xd0) {
+	if (load) {
 		unsigned long val;
 		get32_unaligned_check(val, addr);
 		regs->uregs[rd] = val;
 		get32_unaligned_check(val, addr + 4);
-		regs->uregs[rd + 1] = val;
+		regs->uregs[rd2] = val;
 	} else {
 		put32_unaligned_check(regs->uregs[rd], addr);
-		put32_unaligned_check(regs->uregs[rd + 1], addr + 4);
+		put32_unaligned_check(regs->uregs[rd2], addr + 4);
 	}
 
 	return TYPE_LDST;
 
  user:
-	if ((instr & 0xf0) == 0xd0) {
+	if (load) {
 		unsigned long val;
 		get32t_unaligned_check(val, addr);
 		regs->uregs[rd] = val;
 		get32t_unaligned_check(val, addr + 4);
-		regs->uregs[rd + 1] = val;
+		regs->uregs[rd2] = val;
 	} else {
 		put32t_unaligned_check(regs->uregs[rd], addr);
-		put32t_unaligned_check(regs->uregs[rd + 1], addr + 4);
+		put32t_unaligned_check(regs->uregs[rd2], addr + 4);
 	}
 
 	return TYPE_LDST;
@@ -616,8 +632,72 @@ thumb2arm(u16 tinstr)
 		/* Else fall through for illegal instruction case */
 
 	default:
-		return 0xdeadc0de;
+		return BAD_INSTR;
+	}
+}
+
+/*
+ * Convert Thumb-2 32 bit LDM, STM, LDRD, STRD to equivalent instruction
+ * handlable by ARM alignment handler, also find the corresponding handler,
+ * so that we can reuse ARM userland alignment fault fixups for Thumb.
+ *
+ * @pinstr: original Thumb-2 instruction; returns new handlable instruction
+ * @regs: register context.
+ * @poffset: return offset from faulted addr for later writeback
+ *
+ * NOTES:
+ * 1. Comments below refer to ARMv7 DDI0406A Thumb Instruction sections.
+ * 2. Register name Rt from ARMv7 is same as Rd from ARMv6 (Rd is Rt)
+ */
+static void *
+do_alignment_t32_to_handler(unsigned long *pinstr, struct pt_regs *regs,
+			    union offset_union *poffset)
+{
+	unsigned long instr = *pinstr;
+	u16 tinst1 = (instr >> 16) & 0xffff;
+	u16 tinst2 = instr & 0xffff;
+	poffset->un = 0;
+
+	switch (tinst1 & 0xffe0) {
+	/* A6.3.5 Load/Store multiple */
+	case 0xe880:		/* STM/STMIA/STMEA,LDM/LDMIA, PUSH/POP T2 */
+	case 0xe8a0:		/* ...above writeback version */
+	case 0xe900:		/* STMDB/STMFD, LDMDB/LDMEA */
+	case 0xe920:		/* ...above writeback version */
+		/* no need offset decision since handler calculates it */
+		return do_alignment_ldmstm;
+
+	case 0xf840:		/* POP/PUSH T3 (single register) */
+		if (RN_BITS(instr) == 13 && (tinst2 & 0x09ff) == 0x0904) {
+			u32 L = !!(LDST_L_BIT(instr));
+			const u32 subset[2] = {
+				0xe92d0000,	/* STMDB sp!,{registers} */
+				0xe8bd0000,	/* LDMIA sp!,{registers} */
+			};
+			*pinstr = subset[L] | (1<<RD_BITS(instr));
+			return do_alignment_ldmstm;
+		}
+		/* Else fall through for illegal instruction case */
+		break;
+
+	/* A6.3.6 Load/store double, STRD/LDRD(immed, lit, reg) */
+	case 0xe860:
+	case 0xe960:
+	case 0xe8e0:
+	case 0xe9e0:
+		poffset->un = (tinst2 & 0xff) << 2;
+	case 0xe940:
+	case 0xe9c0:
+		return do_alignment_ldrdstrd;
+
+	/*
+	 * No need to handle load/store instructions up to word size
+	 * since ARMv6 and later CPUs can perform unaligned accesses.
+	 */
+	default:
+		break;
 	}
+	return NULL;
 }
 
 static int
@@ -630,6 +710,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	mm_segment_t fs;
 	unsigned int fault;
 	u16 tinstr = 0;
+	int isize = 4;
+	int thumb2_32b = 0;
 
 	instrptr = instruction_pointer(regs);
 
@@ -637,8 +719,19 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	set_fs(KERNEL_DS);
 	if (thumb_mode(regs)) {
 		fault = __get_user(tinstr, (u16 *)(instrptr & ~1));
-		if (!(fault))
-			instr = thumb2arm(tinstr);
+		if (!fault) {
+			if (cpu_architecture() >= CPU_ARCH_ARMv7 &&
+			    IS_T32(tinstr)) {
+				/* Thumb-2 32-bit */
+				u16 tinst2 = 0;
+				fault = __get_user(tinst2, (u16 *)(instrptr+2));
+				instr = (tinstr << 16) | tinst2;
+				thumb2_32b = 1;
+			} else {
+				isize = 2;
+				instr = thumb2arm(tinstr);
+			}
+		}
 	} else
 		fault = __get_user(instr, (u32 *)instrptr);
 	set_fs(fs);
@@ -655,7 +748,7 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 
  fixup:
 
-	regs->ARM_pc += thumb_mode(regs) ? 2 : 4;
+	regs->ARM_pc += isize;
 
 	switch (CODING_BITS(instr)) {
 	case 0x00000000:	/* 3.13.4 load/store instruction extensions */
@@ -714,18 +807,25 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 		handler = do_alignment_ldrstr;
 		break;
 
-	case 0x08000000:	/* ldm or stm */
-		handler = do_alignment_ldmstm;
+	case 0x08000000:	/* ldm or stm, or thumb-2 32bit instruction */
+		if (thumb2_32b)
+			handler = do_alignment_t32_to_handler(&instr, regs, &offset);
+		else
+			handler = do_alignment_ldmstm;
 		break;
 
 	default:
 		goto bad;
 	}
 
+	if (!handler)
+		goto bad;
 	type = handler(addr, instr, regs);
 
-	if (type == TYPE_ERROR || type == TYPE_FAULT)
+	if (type == TYPE_ERROR || type == TYPE_FAULT) {
+		regs->ARM_pc -= isize;
 		goto bad_or_fault;
+	}
 
 	if (type == TYPE_LDST)
 		do_alignment_finish_ldst(addr, instr, regs, offset);
@@ -735,7 +835,6 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
  bad_or_fault:
 	if (type == TYPE_ERROR)
 		goto bad;
-	regs->ARM_pc -= thumb_mode(regs) ? 2 : 4;
 	/*
 	 * We got a fault - fix it up, or die.
 	 */
@@ -751,8 +850,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 	 */
 	printk(KERN_ERR "Alignment trap: not handling instruction "
 		"%0*lx at [<%08lx>]\n",
-		thumb_mode(regs) ? 4 : 8,
-		thumb_mode(regs) ? tinstr : instr, instrptr);
+		isize << 1,
+		isize == 2 ? tinstr : instr, instrptr);
 	ai_skipped += 1;
 	return 1;
 
@@ -763,8 +862,8 @@ do_alignment(unsigned long addr, unsigned int fsr, struct pt_regs *regs)
 		printk("Alignment trap: %s (%d) PC=0x%08lx Instr=0x%0*lx "
 		       "Address=0x%08lx FSR 0x%03x\n", current->comm,
 			task_pid_nr(current), instrptr,
-		        thumb_mode(regs) ? 4 : 8,
-		        thumb_mode(regs) ? tinstr : instr,
+			isize << 1,
+			isize == 2 ? tinstr : instr,
 		        addr, fsr);
 
 	if (ai_usermode & UM_FIXUP)

arch/arm/mm/mmu.c

@@ -836,6 +836,13 @@ void __init reserve_node_zero(pg_data_t *pgdat)
 				BOOTMEM_EXCLUSIVE);
 	}
 
+	if (machine_is_treo680()) {
+		reserve_bootmem_node(pgdat, 0xa0000000, 0x1000,
+				BOOTMEM_EXCLUSIVE);
+		reserve_bootmem_node(pgdat, 0xa2000000, 0x1000,
+				BOOTMEM_EXCLUSIVE);
+	}
+
 	if (machine_is_palmt5())
 		reserve_bootmem_node(pgdat, 0xa0200000, 0x1000,
 				BOOTMEM_EXCLUSIVE);

arch/arm/plat-omap/include/mach/sram.h

@@ -24,7 +24,8 @@ extern u32 omap2_set_prcm(u32 dpll_ctrl_val, u32 sdrc_rfr_val, int bypass);
 extern u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl,
 				     u32 sdrc_actim_ctrla,
 				     u32 sdrc_actim_ctrlb, u32 m2,
-				     u32 unlock_dll);
+				     u32 unlock_dll, u32 f, u32 sdrc_mr,
+				     u32 inc);
 
 /* Do not use these */
 extern void omap1_sram_reprogram_clock(u32 ckctl, u32 dpllctl);
@@ -62,7 +63,8 @@ extern unsigned long omap243x_sram_reprogram_sdrc_sz;
 extern u32 omap3_sram_configure_core_dpll(u32 sdrc_rfr_ctrl,
 					  u32 sdrc_actim_ctrla,
 					  u32 sdrc_actim_ctrlb, u32 m2,
-					  u32 unlock_dll);
+					  u32 unlock_dll, u32 f, u32 sdrc_mr,
+					  u32 inc);
 extern unsigned long omap3_sram_configure_core_dpll_sz;
 
 #endif

arch/arm/plat-omap/sram.c

@@ -371,15 +371,17 @@ static inline int omap243x_sram_init(void)
 static u32 (*_omap3_sram_configure_core_dpll)(u32 sdrc_rfr_ctrl,
 					      u32 sdrc_actim_ctrla,
 					      u32 sdrc_actim_ctrlb,
-					      u32 m2, u32 unlock_dll);
+					      u32 m2, u32 unlock_dll,
+					      u32 f, u32 sdrc_mr, u32 inc);
 u32 omap3_configure_core_dpll(u32 sdrc_rfr_ctrl, u32 sdrc_actim_ctrla,
-			      u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll)
+			      u32 sdrc_actim_ctrlb, u32 m2, u32 unlock_dll,
+			      u32 f, u32 sdrc_mr, u32 inc)
 {
 	BUG_ON(!_omap3_sram_configure_core_dpll);
 	return _omap3_sram_configure_core_dpll(sdrc_rfr_ctrl,
 					       sdrc_actim_ctrla,
 					       sdrc_actim_ctrlb, m2,
-					       unlock_dll);
+					       unlock_dll, f, sdrc_mr, inc);
 }
 
 /* REVISIT: Should this be same as omap34xx_sram_init() after off-idle? */

arch/arm/plat-s3c/Makefile

@@ -34,6 +34,7 @@ obj-$(CONFIG_S3C_DEV_HSMMC)	+= dev-hsmmc.o
 obj-$(CONFIG_S3C_DEV_HSMMC1)	+= dev-hsmmc1.o
 obj-y				+= dev-i2c0.o
 obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
+obj-$(CONFIG_SND_S3C24XX_SOC)	+= dev-audio.o
 obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
 obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
 obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o

arch/arm/plat-s3c/dev-audio.c

+/* linux/arch/arm/plat-s3c/dev-audio.c
+ *
+ * Copyright 2009 Wolfson Microelectronics
+ *      Mark Brown <broonie@opensource.wolfsonmicro.com>
+ *
+
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/string.h>
+#include <linux/platform_device.h>
+
+#include <mach/irqs.h>
+#include <mach/map.h>
+
+#include <plat/devs.h>
+
+
+static struct resource s3c64xx_iis0_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IIS0,
+		.end   = S3C64XX_PA_IIS0 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iis0 = {
+	.name		  = "s3c64xx-iis",
+	.id		  = 0,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iis0_resource),
+	.resource	  = s3c64xx_iis0_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis0);
+
+static struct resource s3c64xx_iis1_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IIS1,
+		.end   = S3C64XX_PA_IIS1 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iis1 = {
+	.name		  = "s3c64xx-iis",
+	.id		  = 1,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iis1_resource),
+	.resource	  = s3c64xx_iis1_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iis1);
+
+static struct resource s3c64xx_iisv4_resource[] = {
+	[0] = {
+		.start = S3C64XX_PA_IISV4,
+		.end   = S3C64XX_PA_IISV4 + 0x100 - 1,
+		.flags = IORESOURCE_MEM,
+	},
+};
+
+struct platform_device s3c64xx_device_iisv4 = {
+	.name		  = "s3c64xx-iis-v4",
+	.id		  = -1,
+	.num_resources	  = ARRAY_SIZE(s3c64xx_iisv4_resource),
+	.resource	  = s3c64xx_iisv4_resource,
+};
+EXPORT_SYMBOL(s3c64xx_device_iisv4);

arch/arm/plat-s3c/gpio-config.c

@@ -119,7 +119,7 @@ int s3c_gpio_setcfg_s3c64xx_4bit(struct s3c_gpio_chip *chip,
 	unsigned int shift = (off & 7) * 4;
 	u32 con;
 
-	if (off < 8 && chip->chip.ngpio >= 8)
+	if (off < 8 && chip->chip.ngpio > 8)
 		reg -= 4;
 
 	if (s3c_gpio_is_cfg_special(cfg)) {

arch/arm/plat-s3c/include/plat/devs.h

@@ -24,13 +24,16 @@ extern struct platform_device *s3c24xx_uart_src[];
 
 extern struct platform_device s3c_device_timer[];
 
+extern struct platform_device s3c64xx_device_iis0;
+extern struct platform_device s3c64xx_device_iis1;
+extern struct platform_device s3c64xx_device_iisv4;
+
 extern struct platform_device s3c_device_fb;
 extern struct platform_device s3c_device_usb;
 extern struct platform_device s3c_device_lcd;
 extern struct platform_device s3c_device_wdt;
 extern struct platform_device s3c_device_i2c0;
 extern struct platform_device s3c_device_i2c1;
-extern struct platform_device s3c_device_iis;
 extern struct platform_device s3c_device_rtc;
 extern struct platform_device s3c_device_adc;
 extern struct platform_device s3c_device_sdi;

arch/arm/plat-s3c64xx/Makefile

@@ -23,6 +23,7 @@ obj-y				+= gpiolib.o
 
 obj-$(CONFIG_CPU_S3C6400_INIT)	+= s3c6400-init.o
 obj-$(CONFIG_CPU_S3C6400_CLOCK)	+= s3c6400-clock.o
+obj-$(CONFIG_CPU_FREQ_S3C64XX)  += cpufreq.o
 
 # PM support
 

arch/arm/plat-s3c64xx/clock.c

@@ -191,7 +191,7 @@ static struct clk init_clocks[] = {
 		.id		= -1,
 		.parent		= &clk_h,
 		.enable		= s3c64xx_hclk_ctrl,
-		.ctrlbit	= S3C_CLKCON_SCLK_UHOST,
+		.ctrlbit	= S3C_CLKCON_HCLK_UHOST,
 	}, {
 		.name		= "hsmmc",
 		.id		= 0,

arch/arm/plat-s3c64xx/cpufreq.c

+/* linux/arch/arm/plat-s3c64xx/cpufreq.c
+ *
+ * Copyright 2009 Wolfson Microelectronics plc
+ *
+ * S3C64xx CPUfreq Support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/regulator/consumer.h>
+
+static struct clk *armclk;
+static struct regulator *vddarm;
+
+#ifdef CONFIG_CPU_S3C6410
+struct s3c64xx_dvfs {
+	unsigned int vddarm_min;
+	unsigned int vddarm_max;
+};
+
+static struct s3c64xx_dvfs s3c64xx_dvfs_table[] = {
+	[0] = { 1000000, 1000000 },
+	[1] = { 1000000, 1050000 },
+	[2] = { 1050000, 1100000 },
+	[3] = { 1050000, 1150000 },
+	[4] = { 1250000, 1350000 },
+};
+
+static struct cpufreq_frequency_table s3c64xx_freq_table[] = {
+	{ 0,  66000 },
+	{ 0, 133000 },
+	{ 1, 222000 },
+	{ 1, 266000 },
+	{ 2, 333000 },
+	{ 2, 400000 },
+	{ 3, 532000 },
+	{ 3, 533000 },
+	{ 4, 667000 },
+	{ 0, CPUFREQ_TABLE_END },
+};
+#endif
+
+static int s3c64xx_cpufreq_verify_speed(struct cpufreq_policy *policy)
+{
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	return cpufreq_frequency_table_verify(policy, s3c64xx_freq_table);
+}
+
+static unsigned int s3c64xx_cpufreq_get_speed(unsigned int cpu)
+{
+	if (cpu != 0)
+		return 0;
+
+	return clk_get_rate(armclk) / 1000;
+}
+
+static int s3c64xx_cpufreq_set_target(struct cpufreq_policy *policy,
+				      unsigned int target_freq,
+				      unsigned int relation)
+{
+	int ret;
+	unsigned int i;
+	struct cpufreq_freqs freqs;
+	struct s3c64xx_dvfs *dvfs;
+
+	ret = cpufreq_frequency_table_target(policy, s3c64xx_freq_table,
+					     target_freq, relation, &i);
+	if (ret != 0)
+		return ret;
+
+	freqs.cpu = 0;
+	freqs.old = clk_get_rate(armclk) / 1000;
+	freqs.new = s3c64xx_freq_table[i].frequency;
+	freqs.flags = 0;
+	dvfs = &s3c64xx_dvfs_table[s3c64xx_freq_table[i].index];
+
+	if (freqs.old == freqs.new)
+		return 0;
+
+	pr_debug("cpufreq: Transition %d-%dkHz\n", freqs.old, freqs.new);
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+
+#ifdef CONFIG_REGULATOR
+	if (vddarm && freqs.new > freqs.old) {
+		ret = regulator_set_voltage(vddarm,
+					    dvfs->vddarm_min,
+					    dvfs->vddarm_max);
+		if (ret != 0) {
+			pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+			       freqs.new, ret);
+			goto err;
+		}
+	}
+#endif
+
+	ret = clk_set_rate(armclk, freqs.new * 1000);
+	if (ret < 0) {
+		pr_err("cpufreq: Failed to set rate %dkHz: %d\n",
+		       freqs.new, ret);
+		goto err;
+	}
+
+#ifdef CONFIG_REGULATOR
+	if (vddarm && freqs.new < freqs.old) {
+		ret = regulator_set_voltage(vddarm,
+					    dvfs->vddarm_min,
+					    dvfs->vddarm_max);
+		if (ret != 0) {
+			pr_err("cpufreq: Failed to set VDDARM for %dkHz: %d\n",
+			       freqs.new, ret);
+			goto err_clk;
+		}
+	}
+#endif
+
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	pr_debug("cpufreq: Set actual frequency %lukHz\n",
+		 clk_get_rate(armclk) / 1000);
+
+	return 0;
+
+err_clk:
+	if (clk_set_rate(armclk, freqs.old * 1000) < 0)
+		pr_err("Failed to restore original clock rate\n");
+err:
+	cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+	return ret;
+}
+
+#ifdef CONFIG_REGULATOR
+static void __init s3c64xx_cpufreq_constrain_voltages(void)
+{
+	int count, v, i, found;
+	struct cpufreq_frequency_table *freq;
+	struct s3c64xx_dvfs *dvfs;
+
+	count = regulator_count_voltages(vddarm);
+	if (count < 0) {
+		pr_err("cpufreq: Unable to check supported voltages\n");
+		return;
+	}
+
+	freq = s3c64xx_freq_table;
+	while (freq->frequency != CPUFREQ_TABLE_END) {
+		if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+			continue;
+
+		dvfs = &s3c64xx_dvfs_table[freq->index];
+		found = 0;
+
+		for (i = 0; i < count; i++) {
+			v = regulator_list_voltage(vddarm, i);
+			if (v >= dvfs->vddarm_min && v <= dvfs->vddarm_max)
+				found = 1;
+		}
+
+		if (!found) {
+			pr_debug("cpufreq: %dkHz unsupported by regulator\n",
+				 freq->frequency);
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+		}
+
+		freq++;
+	}
+}
+#endif
+
+static int __init s3c64xx_cpufreq_driver_init(struct cpufreq_policy *policy)
+{
+	int ret;
+	struct cpufreq_frequency_table *freq;
+
+	if (policy->cpu != 0)
+		return -EINVAL;
+
+	if (s3c64xx_freq_table == NULL) {
+		pr_err("cpufreq: No frequency information for this CPU\n");
+		return -ENODEV;
+	}
+
+	armclk = clk_get(NULL, "armclk");
+	if (IS_ERR(armclk)) {
+		pr_err("cpufreq: Unable to obtain ARMCLK: %ld\n",
+		       PTR_ERR(armclk));
+		return PTR_ERR(armclk);
+	}
+
+#ifdef CONFIG_REGULATOR
+	vddarm = regulator_get(NULL, "vddarm");
+	if (IS_ERR(vddarm)) {
+		ret = PTR_ERR(vddarm);
+		pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret);
+		pr_err("cpufreq: Only frequency scaling available\n");
+		vddarm = NULL;
+	} else {
+		s3c64xx_cpufreq_constrain_voltages();
+	}
+#endif
+
+	freq = s3c64xx_freq_table;
+	while (freq->frequency != CPUFREQ_TABLE_END) {
+		unsigned long r;
+
+		/* Check for frequencies we can generate */
+		r = clk_round_rate(armclk, freq->frequency * 1000);
+		r /= 1000;
+		if (r != freq->frequency)
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+		/* If we have no regulator then assume startup
+		 * frequency is the maximum we can support. */
+		if (!vddarm && freq->frequency > s3c64xx_cpufreq_get_speed(0))
+			freq->frequency = CPUFREQ_ENTRY_INVALID;
+
+		freq++;
+	}
+
+	policy->cur = clk_get_rate(armclk) / 1000;
+
+	/* Pick a conservative guess in ns: we'll need ~1 I2C/SPI
+	 * write plus clock reprogramming. */
+	policy->cpuinfo.transition_latency = 2 * 1000 * 1000;
+
+	ret = cpufreq_frequency_table_cpuinfo(policy, s3c64xx_freq_table);
+	if (ret != 0) {
+		pr_err("cpufreq: Failed to configure frequency table: %d\n",
+		       ret);
+		regulator_put(vddarm);
+		clk_put(armclk);
+	}
+
+	return ret;
+}
+
+static struct cpufreq_driver s3c64xx_cpufreq_driver = {
+	.owner		= THIS_MODULE,
+	.flags          = 0,
+	.verify		= s3c64xx_cpufreq_verify_speed,
+	.target		= s3c64xx_cpufreq_set_target,
+	.get		= s3c64xx_cpufreq_get_speed,
+	.init		= s3c64xx_cpufreq_driver_init,
+	.name		= "s3c",
+};
+
+static int __init s3c64xx_cpufreq_init(void)
+{
+	return cpufreq_register_driver(&s3c64xx_cpufreq_driver);
+}
+module_init(s3c64xx_cpufreq_init);

arch/arm/plat-s3c64xx/gpiolib.c

@@ -321,6 +321,11 @@ static struct s3c_gpio_cfg gpio_2bit_cfg_eint11 = {
 	.get_pull	= s3c_gpio_getpull_updown,
 };
 
+int s3c64xx_gpio2int_gpn(struct gpio_chip *chip, unsigned pin)
+{
+	return IRQ_EINT(0) + pin;
+}
+
 static struct s3c_gpio_chip gpio_2bit[] = {
 	{
 		.base	= S3C64XX_GPF_BASE,
@@ -353,6 +358,7 @@ static struct s3c_gpio_chip gpio_2bit[] = {
 			.base	= S3C64XX_GPN(0),
 			.ngpio	= S3C64XX_GPIO_N_NR,
 			.label	= "GPN",
+			.to_irq = s3c64xx_gpio2int_gpn,
 		},
 	}, {
 		.base	= S3C64XX_GPO_BASE,

arch/arm/plat-s3c64xx/include/plat/regs-clock.h

@@ -88,11 +88,11 @@
 #define S3C6400_CLKDIV2_SPI0_SHIFT	(0)
 
 /* HCLK GATE Registers */
-#define S3C_CLKCON_HCLK_BUS	(1<<30)
-#define S3C_CLKCON_HCLK_SECUR	(1<<29)
-#define S3C_CLKCON_HCLK_SDMA1	(1<<28)
-#define S3C_CLKCON_HCLK_SDMA2	(1<<27)
-#define S3C_CLKCON_HCLK_UHOST	(1<<26)
+#define S3C_CLKCON_HCLK_3DSE	(1<<31)
+#define S3C_CLKCON_HCLK_UHOST	(1<<29)
+#define S3C_CLKCON_HCLK_SECUR	(1<<28)
+#define S3C_CLKCON_HCLK_SDMA1	(1<<27)
+#define S3C_CLKCON_HCLK_SDMA0	(1<<26)
 #define S3C_CLKCON_HCLK_IROM	(1<<25)
 #define S3C_CLKCON_HCLK_DDR1	(1<<24)
 #define S3C_CLKCON_HCLK_DDR0	(1<<23)

arch/arm/tools/mach-types

@@ -12,7 +12,7 @@
 #
 #   http://www.arm.linux.org.uk/developer/machines/?action=new
 #
-# Last update: Fri May 29 10:14:20 2009
+# Last update: Sat Jun 20 22:28:39 2009
 #
 # machine_is_xxx	CONFIG_xxxx		MACH_TYPE_xxx		number
 #
@@ -1455,7 +1455,7 @@ gba			MACH_GBA		GBA			1457
 h6044			MACH_H6044		H6044			1458
 app			MACH_APP		APP			1459
 tct_hammer		MACH_TCT_HAMMER		TCT_HAMMER		1460
-herald			MACH_HERMES		HERMES			1461
+herald			MACH_HERALD		HERALD			1461
 artemis			MACH_ARTEMIS		ARTEMIS			1462
 htctitan		MACH_HTCTITAN		HTCTITAN		1463
 qranium			MACH_QRANIUM		QRANIUM			1464
@@ -2245,3 +2245,38 @@ str9			MACH_STR9		STR9			2257
 omap3_wl_ff		MACH_OMAP3_WL_FF	OMAP3_WL_FF		2258
 simcom			MACH_SIMCOM		SIMCOM			2259
 mcwebio			MACH_MCWEBIO		MCWEBIO			2260
+omap3_phrazer		MACH_OMAP3_PHRAZER	OMAP3_PHRAZER		2261
+darwin			MACH_DARWIN		DARWIN			2262
+oratiscomu		MACH_ORATISCOMU		ORATISCOMU		2263
+rtsbc20			MACH_RTSBC20		RTSBC20			2264
+i780			MACH_I780		I780			2265
+gemini324		MACH_GEMINI324		GEMINI324		2266
+oratislan		MACH_ORATISLAN		ORATISLAN		2267
+oratisalog		MACH_ORATISALOG		ORATISALOG		2268
+oratismadi		MACH_ORATISMADI		ORATISMADI		2269
+oratisot16		MACH_ORATISOT16		ORATISOT16		2270
+oratisdesk		MACH_ORATISDESK		ORATISDESK		2271
+v2p_ca9			MACH_V2P_CA9		V2P_CA9			2272
+sintexo			MACH_SINTEXO		SINTEXO			2273
+cm3389			MACH_CM3389		CM3389			2274
+omap3_cio		MACH_OMAP3_CIO		OMAP3_CIO		2275
+sgh_i900		MACH_SGH_I900		SGH_I900		2276
+bst100			MACH_BST100		BST100			2277
+passion			MACH_PASSION		PASSION			2278
+indesign_at91sam	MACH_INDESIGN_AT91SAM	INDESIGN_AT91SAM	2279
+c4_badger		MACH_C4_BADGER		C4_BADGER		2280
+c4_viper		MACH_C4_VIPER		C4_VIPER		2281
+d2net			MACH_D2NET		D2NET			2282
+bigdisk			MACH_BIGDISK		BIGDISK			2283
+notalvision		MACH_NOTALVISION	NOTALVISION		2284
+omap3_kboc		MACH_OMAP3_KBOC		OMAP3_KBOC		2285
+cyclone			MACH_CYCLONE		CYCLONE			2286
+ninja			MACH_NINJA		NINJA			2287
+at91sam9g20ek_2mmc	MACH_AT91SAM9G20EK_2MMC	AT91SAM9G20EK_2MMC	2288
+bcmring			MACH_BCMRING		BCMRING			2289
+resol_dl2		MACH_RESOL_DL2		RESOL_DL2		2290
+ifosw			MACH_IFOSW		IFOSW			2291
+htcrhodium		MACH_HTCRHODIUM		HTCRHODIUM		2292
+htctopaz		MACH_HTCTOPAZ		HTCTOPAZ		2293
+matrix504		MACH_MATRIX504		MATRIX504		2294
+mrfsa			MACH_MRFSA		MRFSA			2295

sound/soc/pxa/corgi.c

@@ -320,38 +320,6 @@ static struct snd_soc_device corgi_snd_devdata = {
 	.codec_dev = &soc_codec_dev_wm8731,
 };
 
-/*
- * FIXME: This is a temporary bodge to avoid cross-tree merge issues.
- * New drivers should register the wm8731 I2C device in the machine
- * setup code (under arch/arm for ARM systems).
- */
-static int wm8731_i2c_register(void)
-{
-	struct i2c_board_info info;
-	struct i2c_adapter *adapter;
-	struct i2c_client *client;
-
-	memset(&info, 0, sizeof(struct i2c_board_info));
-	info.addr = 0x1b;
-	strlcpy(info.type, "wm8731", I2C_NAME_SIZE);
-
-	adapter = i2c_get_adapter(0);
-	if (!adapter) {
-		printk(KERN_ERR "can't get i2c adapter 0\n");
-		return -ENODEV;
-	}
-
-	client = i2c_new_device(adapter, &info);
-	i2c_put_adapter(adapter);
-	if (!client) {
-		printk(KERN_ERR "can't add i2c device at 0x%x\n",
-			(unsigned int)info.addr);
-		return -ENODEV;
-	}
-
-	return 0;
-}
-
 static struct platform_device *corgi_snd_device;
 
 static int __init corgi_init(void)
@@ -362,10 +330,6 @@ static int __init corgi_init(void)
 	      machine_is_husky()))
 		return -ENODEV;
 
-	ret = wm8731_i2c_register();
-	if (ret != 0)
-		return ret;
-
 	corgi_snd_device = platform_device_alloc("soc-audio", -1);
 	if (!corgi_snd_device)
 		return -ENOMEM;

sound/soc/pxa/poodle.c

@@ -280,38 +280,6 @@ static struct snd_soc_card snd_soc_poodle = {
 	.num_links = 1,
 };
 
-/*
- * FIXME: This is a temporary bodge to avoid cross-tree merge issues.
- * New drivers should register the wm8731 I2C device in the machine
- * setup code (under arch/arm for ARM systems).
- */
-static int wm8731_i2c_register(void)
-{
-	struct i2c_board_info info;
-	struct i2c_adapter *adapter;
-	struct i2c_client *client;
-
-	memset(&info, 0, sizeof(struct i2c_board_info));
-	info.addr = 0x1b;
-	strlcpy(info.type, "wm8731", I2C_NAME_SIZE);
-
-	adapter = i2c_get_adapter(0);
-	if (!adapter) {
-		printk(KERN_ERR "can't get i2c adapter 0\n");
-		return -ENODEV;
-	}
-
-	client = i2c_new_device(adapter, &info);
-	i2c_put_adapter(adapter);
-	if (!client) {
-		printk(KERN_ERR "can't add i2c device at 0x%x\n",
-			(unsigned int)info.addr);
-		return -ENODEV;
-	}
-
-	return 0;
-}
-
 /* poodle audio subsystem */
 static struct snd_soc_device poodle_snd_devdata = {
 	.card = &snd_soc_poodle,
@@ -327,10 +295,6 @@ static int __init poodle_init(void)
 	if (!machine_is_poodle())
 		return -ENODEV;
 
-	ret = wm8731_i2c_register();
-	if (ret != 0)
-		return ret;
-
 	locomo_gpio_set_dir(&poodle_locomo_device.dev,
 		POODLE_LOCOMO_GPIO_AMP_ON, 0);
 	/* should we mute HP at startup - burning power ?*/