Merge tag 'devicetree-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux

Pull devicetree updates from Rob Herring:

 - Refactor arch kdump DT related code to a common implementation

 - Add fw_devlink tracking for 'phy-handle', 'leds', 'backlight',
   'resets', and 'pwm' properties

 - Various clean-ups to DT FDT code

 - Fix a runtime error for !CONFIG_SYSFS

 - Convert Synopsys DW PCI and derivative binding docs to schemas. Add
   Toshiba Visconti PCIe binding.

 - Convert a bunch of memory controller bindings to schemas

 - Covert eeprom-93xx46, Samsung Exynos TRNG, Samsung Exynos IRQ
   combiner, arm-charlcd, img-ascii-lcd, UniPhier eFuse, Xilinx Zynq
   MPSoC FPGA, Xilinx Zynq MPSoC reset, Mediatek mmsys, Gemini boards,
   brcm,iproc-i2c, faraday,ftpci100, and ks8851 net to DT schema.

 - Extend nvmem bindings to handle bit offsets in unit-addresses

 - Add DT schemas for HiKey 970 PCIe PHY

 - Remove unused ZTE, energymicro,efm32-timer, and Exynos SATA bindings

 - Enable dtc pci_device_reg warning by default

 - Fixes for handling 'unevaluatedProperties' in preparation to enable
   pending support in the tooling for jsonschema 2020-12 draft

* tag 'devicetree-for-5.15' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (78 commits)
  dt-bindings: display: remove zte,vou.txt binding doc
  dt-bindings: hwmon: merge max1619 into trivial devices
  dt-bindings: mtd-physmap: Add 'arm,vexpress-flash' compatible
  dt-bindings: PCI: imx6: convert the imx pcie controller to dtschema
  dt-bindings: Use 'enum' instead of 'oneOf' plus 'const' entries
  dt-bindings: Add vendor prefix for Topic Embedded Systems
  of: fdt: Rename reserve_elfcorehdr() to fdt_reserve_elfcorehdr()
  arm64: kdump: Remove custom linux,usable-memory-range handling
  arm64: kdump: Remove custom linux,elfcorehdr handling
  riscv: Remove non-standard linux,elfcorehdr handling
  of: fdt: Use IS_ENABLED(CONFIG_BLK_DEV_INITRD) instead of #ifdef
  of: fdt: Add generic support for handling usable memory range property
  of: fdt: Add generic support for handling elf core headers property
  crash_dump: Make elfcorehdr address/size symbols always visible
  dt-bindings: memory: convert Samsung Exynos DMC to dtschema
  dt-bindings: devfreq: event: convert Samsung Exynos PPMU to dtschema
  dt-bindings: devfreq: event: convert Samsung Exynos NoCP to dtschema
  kbuild: Enable dtc 'pci_device_reg' warning by default
  dt-bindings: soc: remove obsolete zte zx header
  dt-bindings: clock: remove obsolete zte zx header
  ...

Documentation/devicetree/bindings/Makefile

@@ -28,7 +28,7 @@ find_cmd = find $(srctree)/$(src) \( -name '*.yaml' ! \
 
 quiet_cmd_yamllint = LINT    $(src)
       cmd_yamllint = ($(find_cmd) | \
-                     xargs $(DT_SCHEMA_LINT) -f parsable -c $(srctree)/$(src)/.yamllint) || true
+                     xargs $(DT_SCHEMA_LINT) -f parsable -c $(srctree)/$(src)/.yamllint >&2) || true
 
 quiet_cmd_chk_bindings = CHKDT   $@
       cmd_chk_bindings = ($(find_cmd) | \

Documentation/devicetree/bindings/arm/gemini.txt

-Cortina systems Gemini platforms
-
-The Gemini SoC is the project name for an ARMv4 FA525-based SoC originally
-produced by Storlink Semiconductor around 2005. The company was renamed
-later renamed Storm Semiconductor. The chip product name is Storlink SL3516.
-It was derived from earlier products from Storm named SL3316 (Centroid) and
-SL3512 (Bulverde).
-
-Storm Semiconductor was acquired by Cortina Systems in 2008 and the SoC was
-produced and used for NAS and similar usecases. In 2014 Cortina Systems was
-in turn acquired by Inphi, who seem to have discontinued this product family.
-
-Many of the IP blocks used in the SoC comes from Faraday Technology.
-
-Required properties (in root node):
-	compatible = "cortina,gemini";
-
-Required nodes:
-
-- soc: the SoC should be represented by a simple bus encompassing all the
-  onchip devices, this is referred to as the soc bus node.
-
-- syscon: the soc bus node must have a system controller node pointing to the
-  global control registers, with the compatible string
-  "cortina,gemini-syscon", "syscon";
-
-  Required properties on the syscon:
-  - reg: syscon register location and size.
-  - #clock-cells: should be set to <1> - the system controller is also a
-                  clock provider.
-  - #reset-cells: should be set to <1> - the system controller is also a
-                  reset line provider.
-
-  The clock sources have shorthand defines in the include file:
-  <dt-bindings/clock/cortina,gemini-clock.h>
-
-  The reset lines have shorthand defines in the include file:
-  <dt-bindings/reset/cortina,gemini-reset.h>
-
-- timer: the soc bus node must have a timer node pointing to the SoC timer
-  block, with the compatible string "cortina,gemini-timer"
-  See: clocksource/cortina,gemini-timer.txt
-
-- interrupt-controller: the sob bus node must have an interrupt controller
-  node pointing to the SoC interrupt controller block, with the compatible
-  string "cortina,gemini-interrupt-controller"
-  See interrupt-controller/cortina,gemini-interrupt-controller.txt
-
-Example:
-
-/ {
-	model = "Foo Gemini Machine";
-	compatible = "cortina,gemini";
-	#address-cells = <1>;
-	#size-cells = <1>;
-
-	memory {
-		device_type = "memory";
-		reg = <0x00000000 0x8000000>;
-	};
-
-	soc {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-		compatible = "simple-bus";
-		interrupt-parent = <&intcon>;
-
-		syscon: syscon@40000000 {
-			compatible = "cortina,gemini-syscon", "syscon";
-			reg = <0x40000000 0x1000>;
-			#clock-cells = <1>;
-			#reset-cells = <1>;
-		};
-
-		uart0: serial@42000000 {
-			compatible = "ns16550a";
-			reg = <0x42000000 0x100>;
-			resets = <&syscon GEMINI_RESET_UART>;
-			clocks = <&syscon GEMINI_CLK_UART>;
-			interrupts = <18 IRQ_TYPE_LEVEL_HIGH>;
-			reg-shift = <2>;
-		};
-
-		timer@43000000 {
-			compatible = "cortina,gemini-timer";
-			reg = <0x43000000 0x1000>;
-			interrupt-parent = <&intcon>;
-			interrupts = <14 IRQ_TYPE_EDGE_FALLING>, /* Timer 1 */
-				     <15 IRQ_TYPE_EDGE_FALLING>, /* Timer 2 */
-				     <16 IRQ_TYPE_EDGE_FALLING>; /* Timer 3 */
-			resets = <&syscon GEMINI_RESET_TIMER>;
-			/* APB clock or RTC clock */
-			clocks = <&syscon GEMINI_CLK_APB>,
-				 <&syscon GEMINI_CLK_RTC>;
-			clock-names = "PCLK", "EXTCLK";
-			syscon = <&syscon>;
-		};
-
-		intcon: interrupt-controller@48000000 {
-			compatible = "cortina,gemini-interrupt-controller";
-			reg = <0x48000000 0x1000>;
-			resets = <&syscon GEMINI_RESET_INTCON0>;
-			interrupt-controller;
-			#interrupt-cells = <2>;
-		};
-	};
-};

Documentation/devicetree/bindings/arm/gemini.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/arm/gemini.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cortina systems Gemini platforms
+
+description: |
+  The Gemini SoC is the project name for an ARMv4 FA525-based SoC originally
+  produced by Storlink Semiconductor around 2005. The company was renamed
+  later renamed Storm Semiconductor. The chip product name is Storlink SL3516.
+  It was derived from earlier products from Storm named SL3316 (Centroid) and
+  SL3512 (Bulverde).
+
+  Storm Semiconductor was acquired by Cortina Systems in 2008 and the SoC was
+  produced and used for NAS and similar usecases. In 2014 Cortina Systems was
+  in turn acquired by Inphi, who seem to have discontinued this product family.
+
+  Many of the IP blocks used in the SoC comes from Faraday Technology.
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    oneOf:
+
+      - description: Storlink Semiconductor Gemini324 EV-Board also known
+          as Storm Semiconductor SL93512R_BRD
+        items:
+          - const: storlink,gemini324
+          - const: storm,sl93512r
+          - const: cortina,gemini
+
+      - description: D-Link DIR-685 Xtreme N Storage Router
+        items:
+          - const: dlink,dir-685
+          - const: cortina,gemini
+
+      - description: D-Link DNS-313 1-Bay Network Storage Enclosure
+        items:
+          - const: dlink,dns-313
+          - const: cortina,gemini
+
+      - description: Edimax NS-2502
+        items:
+          - const: edimax,ns-2502
+          - const: cortina,gemini
+
+      - description: ITian Square One SQ201
+        items:
+          - const: itian,sq201
+          - const: cortina,gemini
+
+      - description: Raidsonic NAS IB-4220-B
+        items:
+          - const: raidsonic,ib-4220-b
+          - const: cortina,gemini
+
+      - description: SSI 1328
+        items:
+          - const: ssi,1328
+          - const: cortina,gemini
+
+      - description: Teltonika RUT1xx Mobile Router
+        items:
+          - const: teltonika,rut1xx
+          - const: cortina,gemini
+
+      - description: Wiligear Wiliboard WBD-111
+        items:
+          - const: wiligear,wiliboard-wbd111
+          - const: cortina,gemini
+
+      - description: Wiligear Wiliboard WBD-222
+        items:
+          - const: wiligear,wiliboard-wbd222
+          - const: cortina,gemini
+
+      - description: Wiligear Wiliboard WBD-111 - old incorrect binding
+        items:
+          - const: wiliboard,wbd111
+          - const: cortina,gemini
+        deprecated: true
+
+      - description: Wiligear Wiliboard WBD-222 - old incorrect binding
+        items:
+          - const: wiliboard,wbd222
+          - const: cortina,gemini
+        deprecated: true
+
+additionalProperties: true

Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.txt

-Mediatek mmsys controller
-============================
-
-The Mediatek mmsys system controller provides clock control, routing control,
-and miscellaneous control in mmsys partition.
-
-Required Properties:
-
-- compatible: Should be one of:
-	- "mediatek,mt2701-mmsys", "syscon"
-	- "mediatek,mt2712-mmsys", "syscon"
-	- "mediatek,mt6765-mmsys", "syscon"
-	- "mediatek,mt6779-mmsys", "syscon"
-	- "mediatek,mt6797-mmsys", "syscon"
-	- "mediatek,mt7623-mmsys", "mediatek,mt2701-mmsys", "syscon"
-	- "mediatek,mt8167-mmsys", "syscon"
-	- "mediatek,mt8173-mmsys", "syscon"
-	- "mediatek,mt8183-mmsys", "syscon"
-- #clock-cells: Must be 1
-
-For the clock control, the mmsys controller uses the common clk binding from
-Documentation/devicetree/bindings/clock/clock-bindings.txt
-The available clocks are defined in dt-bindings/clock/mt*-clk.h.
-
-Example:
-
-mmsys: syscon@14000000 {
-	compatible = "mediatek,mt8173-mmsys", "syscon";
-	reg = <0 0x14000000 0 0x1000>;
-	#clock-cells = <1>;
-};

Documentation/devicetree/bindings/arm/mediatek/mediatek,mmsys.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/arm/mediatek/mediatek,mmsys.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: MediaTek mmsys controller
+
+maintainers:
+  - Matthias Brugger <matthias.bgg@gmail.com>
+
+description:
+  The MediaTek mmsys system controller provides clock control, routing control,
+  and miscellaneous control in mmsys partition.
+
+properties:
+  $nodename:
+    pattern: "^syscon@[0-9a-f]+$"
+
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - mediatek,mt2701-mmsys
+              - mediatek,mt2712-mmsys
+              - mediatek,mt6765-mmsys
+              - mediatek,mt6779-mmsys
+              - mediatek,mt6797-mmsys
+              - mediatek,mt8167-mmsys
+              - mediatek,mt8173-mmsys
+              - mediatek,mt8183-mmsys
+              - mediatek,mt8365-mmsys
+          - const: syscon
+      - items:
+          - const: mediatek,mt7623-mmsys
+          - const: mediatek,mt2701-mmsys
+          - const: syscon
+
+  reg:
+    maxItems: 1
+
+  "#clock-cells":
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#clock-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    mmsys: syscon@14000000 {
+        compatible = "mediatek,mt8173-mmsys", "syscon";
+        reg = <0x14000000 0x1000>;
+        #clock-cells = <1>;
+    };

Documentation/devicetree/bindings/ata/exynos-sata.txt

-* Samsung AHCI SATA Controller
-
-SATA nodes are defined to describe on-chip Serial ATA controllers.
-Each SATA controller should have its own node.
-
-Required properties:
-- compatible		: compatible list, contains "samsung,exynos5-sata"
-- interrupts		: <interrupt mapping for SATA IRQ>
-- reg			: <registers mapping>
-- samsung,sata-freq	: <frequency in MHz>
-- phys			: Must contain exactly one entry as specified
-			  in phy-bindings.txt
-- phy-names		: Must be "sata-phy"
-
-Optional properties:
-- clocks		: Must contain an entry for each entry in clock-names.
-- clock-names		: Shall be "sata" for the external SATA bus clock,
-			  and "sclk_sata" for the internal controller clock.
-
-Example:
-	sata@122f0000 {
-		compatible = "snps,dwc-ahci";
-		samsung,sata-freq = <66>;
-		reg = <0x122f0000 0x1ff>;
-		interrupts = <0 115 0>;
-		clocks = <&clock 277>, <&clock 143>;
-		clock-names = "sata", "sclk_sata";
-		phys = <&sata_phy>;
-		phy-names = "sata-phy";
-	};

Documentation/devicetree/bindings/auxdisplay/arm,versatile-lcd.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/auxdisplay/arm,versatile-lcd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ARM Versatile Character LCD
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+  - Rob Herring <robh@kernel.org>
+
+description:
+  This binding defines the character LCD interface found on ARM Versatile AB
+  and PB reference platforms.
+
+properties:
+  compatible:
+    const: arm,versatile-lcd
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    lcd@10008000 {
+            compatible = "arm,versatile-lcd";
+            reg = <0x10008000 0x1000>;
+    };

Documentation/devicetree/bindings/auxdisplay/arm-charlcd.txt

-ARM Versatile Character LCD
------------------------------------------------------
-This binding defines the character LCD interface found on ARM Versatile AB
-and PB reference platforms.
-
-Required properties:
-- compatible : "arm,versatile-clcd"
-- reg : Location and size of character LCD registers
-
-Optional properties:
-- interrupts - single interrupt for character LCD. The character LCD can
-  operate in polled mode without an interrupt.
-
-Example:
-	lcd@10008000 {
-		compatible = "arm,versatile-lcd";
-		reg = <0x10008000 0x1000>;
-	};

Documentation/devicetree/bindings/auxdisplay/img,ascii-lcd.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/auxdisplay/img,ascii-lcd.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ASCII LCD displays on Imagination Technologies boards
+
+maintainers:
+  - Paul Burton <paulburton@kernel.org>
+
+properties:
+  compatible:
+    enum:
+      - img,boston-lcd
+      - mti,malta-lcd
+      - mti,sead3-lcd
+
+  reg:
+    maxItems: 1
+
+  offset:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Offset in bytes to the LCD registers within the system controller
+
+required:
+  - compatible
+
+oneOf:
+  - required:
+      - reg
+  - required:
+      - offset
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: img,boston-lcd
+then:
+  required:
+    - reg
+else:
+  required:
+    - offset
+
+additionalProperties: false
+
+examples:
+  - |
+    lcd: lcd@17fff000 {
+            compatible = "img,boston-lcd";
+            reg = <0x17fff000 0x8>;
+    };

Documentation/devicetree/bindings/auxdisplay/img-ascii-lcd.txt

-Binding for ASCII LCD displays on Imagination Technologies boards
-
-Required properties:
-- compatible : should be one of:
-    "img,boston-lcd"
-    "mti,malta-lcd"
-    "mti,sead3-lcd"
-
-Required properties for "img,boston-lcd":
-- reg : memory region locating the device registers
-
-Required properties for "mti,malta-lcd" or "mti,sead3-lcd":
-- regmap: phandle of the system controller containing the LCD registers
-- offset: offset in bytes to the LCD registers within the system controller
-
-The layout of the registers & properties of the display are determined
-from the compatible string, making this binding somewhat trivial.

Documentation/devicetree/bindings/chosen.txt

@@ -79,9 +79,9 @@ a different secondary CPU release mechanism)
 linux,usable-memory-range
 -------------------------
 
-This property (arm64 only) holds a base address and size, describing a
-limited region in which memory may be considered available for use by
-the kernel. Memory outside of this range is not available for use.
+This property holds a base address and size, describing a limited region in
+which memory may be considered available for use by the kernel. Memory outside
+of this range is not available for use.
 
 This property describes a limitation: memory within this range is only
 valid when also described through another mechanism that the kernel
@@ -106,9 +106,9 @@ respectively, of the root node.
 linux,elfcorehdr
 ----------------
 
-This property (currently used only on arm64) holds the memory range,
-the address and the size, of the elf core header which mainly describes
-the panicked kernel's memory layout as PT_LOAD segments of elf format.
+This property holds the memory range, the address and the size, of the elf
+core header which mainly describes the panicked kernel's memory layout as
+PT_LOAD segments of elf format.
 e.g.
 
 / {

Documentation/devicetree/bindings/devfreq/event/exynos-nocp.txt

-
-* Samsung Exynos NoC (Network on Chip) Probe device
-
-The Samsung Exynos542x SoC has NoC (Network on Chip) Probe for NoC bus.
-NoC provides the primitive values to get the performance data. The packets
-that the Network on Chip (NoC) probes detects are transported over
-the network infrastructure to observer units. You can configure probes to
-capture packets with header or data on the data request response network,
-or as traffic debug or statistic collectors. Exynos542x bus has multiple
-NoC probes to provide bandwidth information about behavior of the SoC
-that you can use while analyzing system performance.
-
-Required properties:
-- compatible: Should be "samsung,exynos5420-nocp"
-- reg: physical base address of each NoC Probe and length of memory mapped region.
-
-Optional properties:
-- clock-names : the name of clock used by the NoC Probe, "nocp"
-- clocks : phandles for clock specified in "clock-names" property
-
-Example : NoC Probe nodes in Device Tree are listed below.
-
-	nocp_mem0_0: nocp@10ca1000 {
-		compatible = "samsung,exynos5420-nocp";
-		reg = <0x10CA1000 0x200>;
-	};

Documentation/devicetree/bindings/devfreq/event/exynos-ppmu.txt

-
-* Samsung Exynos PPMU (Platform Performance Monitoring Unit) device
-
-The Samsung Exynos SoC has PPMU (Platform Performance Monitoring Unit) for
-each IP. PPMU provides the primitive values to get performance data. These
-PPMU events provide information of the SoC's behaviors so that you may
-use to analyze system performance, to make behaviors visible and to count
-usages of each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC).
-The Exynos PPMU driver uses the devfreq-event class to provide event data
-to various devfreq devices. The devfreq devices would use the event data when
-derterming the current state of each IP.
-
-Required properties for PPMU device:
-- compatible: Should be "samsung,exynos-ppmu" or "samsung,exynos-ppmu-v2.
-- reg: physical base address of each PPMU and length of memory mapped region.
-
-Optional properties for PPMU device:
-- clock-names : the name of clock used by the PPMU, "ppmu"
-- clocks : phandles for clock specified in "clock-names" property
-
-Required properties for 'events' child node of PPMU device:
-- event-name : the unique event name among PPMU device
-Optional properties for 'events' child node of PPMU device:
-- event-data-type : Define the type of data which shell be counted
-by the counter. You can check include/dt-bindings/pmu/exynos_ppmu.h for
-all possible type, i.e. count read requests, count write data in bytes,
-etc. This field is optional and when it is missing, the driver code
-will use default data type.
-
-Example1 : PPMUv1 nodes in exynos3250.dtsi are listed below.
-
-		ppmu_dmc0: ppmu_dmc0@106a0000 {
-			compatible = "samsung,exynos-ppmu";
-			reg = <0x106a0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_dmc1: ppmu_dmc1@106b0000 {
-			compatible = "samsung,exynos-ppmu";
-			reg = <0x106b0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_cpu: ppmu_cpu@106c0000 {
-			compatible = "samsung,exynos-ppmu";
-			reg = <0x106c0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_rightbus: ppmu_rightbus@112a0000 {
-			compatible = "samsung,exynos-ppmu";
-			reg = <0x112a0000 0x2000>;
-			clocks = <&cmu CLK_PPMURIGHT>;
-			clock-names = "ppmu";
-			status = "disabled";
-		};
-
-		ppmu_leftbus: ppmu_leftbus0@116a0000 {
-			compatible = "samsung,exynos-ppmu";
-			reg = <0x116a0000 0x2000>;
-			clocks = <&cmu CLK_PPMULEFT>;
-			clock-names = "ppmu";
-			status = "disabled";
-		};
-
-Example2 : Events of each PPMU node in exynos3250-rinato.dts are listed below.
-
-	&ppmu_dmc0 {
-		status = "okay";
-
-		events {
-			ppmu_dmc0_3: ppmu-event3-dmc0 {
-				event-name = "ppmu-event3-dmc0";
-			};
-
-			ppmu_dmc0_2: ppmu-event2-dmc0 {
-				event-name = "ppmu-event2-dmc0";
-			};
-
-			ppmu_dmc0_1: ppmu-event1-dmc0 {
-				event-name = "ppmu-event1-dmc0";
-			};
-
-			ppmu_dmc0_0: ppmu-event0-dmc0 {
-				event-name = "ppmu-event0-dmc0";
-			};
-		};
-	};
-
-	&ppmu_dmc1 {
-		status = "okay";
-
-		events {
-			ppmu_dmc1_3: ppmu-event3-dmc1 {
-				event-name = "ppmu-event3-dmc1";
-			};
-		};
-	};
-
-	&ppmu_leftbus {
-		status = "okay";
-
-		events {
-			ppmu_leftbus_3: ppmu-event3-leftbus {
-				event-name = "ppmu-event3-leftbus";
-			};
-		};
-	};
-
-	&ppmu_rightbus {
-		status = "okay";
-
-		events {
-			ppmu_rightbus_3: ppmu-event3-rightbus {
-				event-name = "ppmu-event3-rightbus";
-			};
-		};
-	};
-
-Example3 : PPMUv2 nodes in exynos5433.dtsi are listed below.
-
-		ppmu_d0_cpu: ppmu_d0_cpu@10480000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x10480000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_d0_general: ppmu_d0_general@10490000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x10490000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_d0_rt: ppmu_d0_rt@104a0000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x104a0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_d1_cpu: ppmu_d1_cpu@104b0000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x104b0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_d1_general: ppmu_d1_general@104c0000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x104c0000 0x2000>;
-			status = "disabled";
-		};
-
-		ppmu_d1_rt: ppmu_d1_rt@104d0000 {
-			compatible = "samsung,exynos-ppmu-v2";
-			reg = <0x104d0000 0x2000>;
-			status = "disabled";
-		};
-
-Example4 : 'event-data-type' in exynos4412-ppmu-common.dtsi are listed below.
-
-	&ppmu_dmc0 {
-		status = "okay";
-		events {
-			ppmu_dmc0_3: ppmu-event3-dmc0 {
-			event-name = "ppmu-event3-dmc0";
-			event-data-type = <(PPMU_RO_DATA_CNT |
-					PPMU_WO_DATA_CNT)>;
-			};
-		};
-	};

Documentation/devicetree/bindings/devfreq/event/samsung,exynos-nocp.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/devfreq/event/samsung,exynos-nocp.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos NoC (Network on Chip) Probe
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+  The Samsung Exynos542x SoC has a NoC (Network on Chip) Probe for NoC bus.
+  NoC provides the primitive values to get the performance data. The packets
+  that the Network on Chip (NoC) probes detects are transported over the
+  network infrastructure to observer units. You can configure probes to capture
+  packets with header or data on the data request response network, or as
+  traffic debug or statistic collectors. Exynos542x bus has multiple NoC probes
+  to provide bandwidth information about behavior of the SoC that you can use
+  while analyzing system performance.
+
+properties:
+  compatible:
+    const: samsung,exynos5420-nocp
+
+  clock-names:
+    items:
+      - const: nocp
+
+  clocks:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    nocp_mem0_0: nocp@10ca1000 {
+        compatible = "samsung,exynos5420-nocp";
+        reg = <0x10ca1000 0x200>;
+    };

Documentation/devicetree/bindings/devfreq/event/samsung,exynos-ppmu.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/devfreq/event/samsung,exynos-ppmu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC PPMU (Platform Performance Monitoring Unit)
+
+maintainers:
+  - Chanwoo Choi <cw00.choi@samsung.com>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+  The Samsung Exynos SoC has PPMU (Platform Performance Monitoring Unit) for
+  each IP. PPMU provides the primitive values to get performance data. These
+  PPMU events provide information of the SoC's behaviors so that you may use to
+  analyze system performance, to make behaviors visible and to count usages of
+  each IP (DMC, CPU, RIGHTBUS, LEFTBUS, CAM interface, LCD, G3D, MFC).  The
+  Exynos PPMU driver uses the devfreq-event class to provide event data to
+  various devfreq devices. The devfreq devices would use the event data when
+  derterming the current state of each IP.
+
+properties:
+  compatible:
+    enum:
+      - samsung,exynos-ppmu
+      - samsung,exynos-ppmu-v2
+
+  clock-names:
+    items:
+      - const: ppmu
+
+  clocks:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+  events:
+    type: object
+
+    patternProperties:
+      '^ppmu-event[0-9]+(-[a-z0-9]+){,2}$':
+        type: object
+        properties:
+          event-name:
+            description: |
+              The unique event name among PPMU device
+            $ref: /schemas/types.yaml#/definitions/string
+
+          event-data-type:
+            description: |
+              Define the type of data which shell be counted by the counter.
+              You can check include/dt-bindings/pmu/exynos_ppmu.h for all
+              possible type, i.e. count read requests, count write data in
+              bytes, etc.  This field is optional and when it is missing, the
+              driver code will use default data type.
+            $ref: /schemas/types.yaml#/definitions/uint32
+
+        required:
+          - event-name
+
+        additionalProperties: false
+
+    additionalProperties: false
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    // PPMUv1 nodes for Exynos3250 (although the board DTS defines events)
+    #include <dt-bindings/clock/exynos3250.h>
+
+    ppmu_dmc0: ppmu@106a0000 {
+        compatible = "samsung,exynos-ppmu";
+        reg = <0x106a0000 0x2000>;
+
+        events {
+            ppmu_dmc0_3: ppmu-event3-dmc0 {
+                event-name = "ppmu-event3-dmc0";
+            };
+
+            ppmu_dmc0_2: ppmu-event2-dmc0 {
+                event-name = "ppmu-event2-dmc0";
+            };
+
+            ppmu_dmc0_1: ppmu-event1-dmc0 {
+                event-name = "ppmu-event1-dmc0";
+            };
+
+            ppmu_dmc0_0: ppmu-event0-dmc0 {
+                event-name = "ppmu-event0-dmc0";
+            };
+        };
+    };
+
+    ppmu_rightbus: ppmu@112a0000 {
+        compatible = "samsung,exynos-ppmu";
+        reg = <0x112a0000 0x2000>;
+        clocks = <&cmu CLK_PPMURIGHT>;
+        clock-names = "ppmu";
+
+        events {
+            ppmu_rightbus_3: ppmu-event3-rightbus {
+                event-name = "ppmu-event3-rightbus";
+            };
+        };
+    };
+
+  - |
+    // PPMUv2 nodes in Exynos5433
+    ppmu_d0_cpu: ppmu@10480000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x10480000 0x2000>;
+    };
+
+    ppmu_d0_general: ppmu@10490000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x10490000 0x2000>;
+
+        events {
+            ppmu_event0_d0_general: ppmu-event0-d0-general {
+                event-name = "ppmu-event0-d0-general";
+            };
+        };
+    };
+
+    ppmu_d0_rt: ppmu@104a0000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x104a0000 0x2000>;
+    };
+
+    ppmu_d1_cpu: ppmu@104b0000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x104b0000 0x2000>;
+    };
+
+    ppmu_d1_general: ppmu@104c0000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x104c0000 0x2000>;
+    };
+
+    ppmu_d1_rt: ppmu@104d0000 {
+        compatible = "samsung,exynos-ppmu-v2";
+        reg = <0x104d0000 0x2000>;
+    };
+
+  - |
+    // PPMUv1 nodes with event-data-type for Exynos4412
+    #include <dt-bindings/pmu/exynos_ppmu.h>
+
+    ppmu@106a0000 {
+        compatible = "samsung,exynos-ppmu";
+        reg = <0x106a0000 0x2000>;
+        clocks = <&clock 400>;
+        clock-names = "ppmu";
+
+        events {
+            ppmu-event3-dmc0 {
+                event-name = "ppmu-event3-dmc0";
+                event-data-type = <(PPMU_RO_DATA_CNT |
+                                    PPMU_WO_DATA_CNT)>;
+            };
+        };
+    };

Documentation/devicetree/bindings/display/allwinner,sun8i-a83t-dw-hdmi.yaml

@@ -174,7 +174,6 @@ examples:
         phy-names = "phy";
         pinctrl-names = "default";
         pinctrl-0 = <&hdmi_pins>;
-        status = "disabled";
 
         ports {
             #address-cells = <1>;
@@ -233,7 +232,6 @@ examples:
         phy-names = "phy";
         pinctrl-names = "default";
         pinctrl-0 = <&hdmi_pins>;
-        status = "disabled";
 
         ports {
             #address-cells = <1>;

Documentation/devicetree/bindings/display/bridge/ti,sn65dsi83.yaml

@@ -37,7 +37,8 @@ properties:
 
     properties:
       port@0:
-        $ref: /schemas/graph.yaml#/properties/port
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
         description: Video port for MIPI DSI Channel-A input
 
         properties:
@@ -57,7 +58,8 @@ properties:
                   - const: 4
 
       port@1:
-        $ref: /schemas/graph.yaml#/properties/port
+        $ref: /schemas/graph.yaml#/$defs/port-base
+        unevaluatedProperties: false
         description: Video port for MIPI DSI Channel-B input
 
         properties:

Documentation/devicetree/bindings/display/fsl,lcdif.yaml

@@ -27,6 +27,7 @@ properties:
               - fsl,imx6ul-lcdif
               - fsl,imx7d-lcdif
               - fsl,imx8mm-lcdif
+              - fsl,imx8mn-lcdif
               - fsl,imx8mq-lcdif
           - const: fsl,imx6sx-lcdif
 

Documentation/devicetree/bindings/display/msm/dsi-controller-main.yaml

@@ -89,7 +89,8 @@ properties:
 
     properties:
       port@0:
-        $ref: "/schemas/graph.yaml#/properties/port"
+        $ref: "/schemas/graph.yaml#/$defs/port-base"
+        unevaluatedProperties: false
         description: |
           Input endpoints of the controller.
         properties:
@@ -104,7 +105,8 @@ properties:
                   enum: [ 0, 1, 2, 3 ]
 
       port@1:
-        $ref: "/schemas/graph.yaml#/properties/port"
+        $ref: "/schemas/graph.yaml#/$defs/port-base"
+        unevaluatedProperties: false
         description: |
           Output endpoints of the controller.
         properties:

Documentation/devicetree/bindings/display/msm/dsi-phy-10nm.yaml

@@ -14,9 +14,9 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: qcom,dsi-phy-10nm
-      - const: qcom,dsi-phy-10nm-8998
+    enum:
+      - qcom,dsi-phy-10nm
+      - qcom,dsi-phy-10nm-8998
 
   reg:
     items:

Documentation/devicetree/bindings/display/msm/dsi-phy-14nm.yaml

@@ -14,9 +14,9 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: qcom,dsi-phy-14nm
-      - const: qcom,dsi-phy-14nm-660
+    enum:
+      - qcom,dsi-phy-14nm
+      - qcom,dsi-phy-14nm-660
 
   reg:
     items:

Documentation/devicetree/bindings/display/msm/dsi-phy-20nm.yaml

@@ -14,8 +14,7 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: qcom,dsi-phy-20nm
+    const: qcom,dsi-phy-20nm
 
   reg:
     items:

Documentation/devicetree/bindings/display/msm/dsi-phy-28nm.yaml

@@ -14,10 +14,10 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: qcom,dsi-phy-28nm-hpm
-      - const: qcom,dsi-phy-28nm-lp
-      - const: qcom,dsi-phy-28nm-8960
+    enum:
+      - qcom,dsi-phy-28nm-hpm
+      - qcom,dsi-phy-28nm-lp
+      - qcom,dsi-phy-28nm-8960
 
   reg:
     items:

Documentation/devicetree/bindings/display/panel/boe,tv101wum-nl6.yaml

@@ -70,7 +70,6 @@ examples:
             avee-supply = <&ppvarp_lcd>;
             pp1800-supply = <&pp1800_lcd>;
             backlight = <&backlight_lcd0>;
-            status = "okay";
             port {
                 panel_in: endpoint {
                     remote-endpoint = <&dsi_out>;

Documentation/devicetree/bindings/display/zte,vou.txt

-ZTE VOU Display Controller
-
-This is a display controller found on ZTE ZX296718 SoC.  It includes multiple
-Graphic Layer (GL) and Video Layer (VL), two Mixers/Channels, and a few blocks
-handling scaling, color space conversion etc.  VOU also integrates the support
-for typical output devices, like HDMI, TV Encoder, VGA, and RGB LCD.
-
-* Master VOU node
-
-It must be the parent node of all the sub-device nodes.
-
-Required properties:
- - compatible: should be "zte,zx296718-vou"
- - #address-cells: should be <1>
- - #size-cells: should be <1>
- - ranges: list of address translations between VOU and sub-devices
-
-* VOU DPC device
-
-Required properties:
- - compatible: should be "zte,zx296718-dpc"
- - reg: Physical base address and length of DPC register regions, one for each
-   entry in 'reg-names'
- - reg-names: The names of register regions. The following regions are required:
-	"osd"
-	"timing_ctrl"
-	"dtrc"
-	"vou_ctrl"
-	"otfppu"
- - interrupts: VOU DPC interrupt number to CPU
- - clocks: A list of phandle + clock-specifier pairs, one for each entry
-   in 'clock-names'
- - clock-names: A list of clock names.  The following clocks are required:
-	"aclk"
-	"ppu_wclk"
-	"main_wclk"
-	"aux_wclk"
-
-* HDMI output device
-
-Required properties:
- - compatible: should be "zte,zx296718-hdmi"
- - reg: Physical base address and length of the HDMI device IO region
- - interrupts : HDMI interrupt number to CPU
- - clocks: A list of phandle + clock-specifier pairs, one for each entry
-   in 'clock-names'
- - clock-names: A list of clock names.  The following clocks are required:
-	"osc_cec"
-	"osc_clk"
-	"xclk"
-
-* TV Encoder output device
-
-Required properties:
- - compatible: should be "zte,zx296718-tvenc"
- - reg: Physical base address and length of the TVENC device IO region
- - zte,tvenc-power-control: the phandle to SYSCTRL block followed by two
-   integer cells.  The first cell is the offset of SYSCTRL register used
-   to control TV Encoder DAC power, and the second cell is the bit mask.
-
-* VGA output device
-
-Required properties:
- - compatible: should be "zte,zx296718-vga"
- - reg: Physical base address and length of the VGA device IO region
- - interrupts : VGA interrupt number to CPU
- - clocks: Phandle with clock-specifier pointing to VGA I2C clock.
- - clock-names: Must be "i2c_wclk".
- - zte,vga-power-control: the phandle to SYSCTRL block followed by two
-   integer cells.  The first cell is the offset of SYSCTRL register used
-   to control VGA DAC power, and the second cell is the bit mask.
-
-Example:
-
-vou: vou@1440000 {
-	compatible = "zte,zx296718-vou";
-	#address-cells = <1>;
-	#size-cells = <1>;
-	ranges = <0 0x1440000 0x10000>;
-
-	dpc: dpc@0 {
-		compatible = "zte,zx296718-dpc";
-		reg = <0x0000 0x1000>, <0x1000 0x1000>,
-		      <0x5000 0x1000>, <0x6000 0x1000>,
-		      <0xa000 0x1000>;
-		reg-names = "osd", "timing_ctrl",
-			    "dtrc", "vou_ctrl",
-			    "otfppu";
-		interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&topcrm VOU_ACLK>, <&topcrm VOU_PPU_WCLK>,
-			 <&topcrm VOU_MAIN_WCLK>, <&topcrm VOU_AUX_WCLK>;
-		clock-names = "aclk", "ppu_wclk",
-			      "main_wclk", "aux_wclk";
-	};
-
-	vga: vga@8000 {
-		compatible = "zte,zx296718-vga";
-		reg = <0x8000 0x1000>;
-		interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&topcrm VGA_I2C_WCLK>;
-		clock-names = "i2c_wclk";
-		zte,vga-power-control = <&sysctrl 0x170 0xe0>;
-	};
-
-	hdmi: hdmi@c000 {
-		compatible = "zte,zx296718-hdmi";
-		reg = <0xc000 0x4000>;
-		interrupts = <GIC_SPI 82 IRQ_TYPE_EDGE_RISING>;
-		clocks = <&topcrm HDMI_OSC_CEC>,
-			 <&topcrm HDMI_OSC_CLK>,
-			 <&topcrm HDMI_XCLK>;
-		clock-names = "osc_cec", "osc_clk", "xclk";
-	};
-
-	tvenc: tvenc@2000 {
-		compatible = "zte,zx296718-tvenc";
-		reg = <0x2000 0x1000>;
-		zte,tvenc-power-control = <&sysctrl 0x170 0x10>;
-	};
-};

Documentation/devicetree/bindings/dma/allwinner,sun6i-a31-dma.yaml

@@ -19,12 +19,12 @@ properties:
     description: The cell is the request line number.
 
   compatible:
-    oneOf:
-      - const: allwinner,sun6i-a31-dma
-      - const: allwinner,sun8i-a23-dma
-      - const: allwinner,sun8i-a83t-dma
-      - const: allwinner,sun8i-h3-dma
-      - const: allwinner,sun8i-v3s-dma
+    enum:
+      - allwinner,sun6i-a31-dma
+      - allwinner,sun8i-a23-dma
+      - allwinner,sun8i-a83t-dma
+      - allwinner,sun8i-h3-dma
+      - allwinner,sun8i-v3s-dma
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/firmware/arm,scpi.yaml

@@ -131,9 +131,9 @@ properties:
 
         properties:
           compatible:
-            oneOf:
-              - const: arm,scpi-dvfs-clocks
-              - const: arm,scpi-variable-clocks
+            enum:
+              - arm,scpi-dvfs-clocks
+              - arm,scpi-variable-clocks
 
           '#clock-cells':
             const: 1

Documentation/devicetree/bindings/fpga/xlnx,zynqmp-pcap-fpga.txt

-Devicetree bindings for Zynq Ultrascale MPSoC FPGA Manager.
-The ZynqMP SoC uses the PCAP (Processor configuration Port) to configure the
-Programmable Logic (PL). The configuration uses  the firmware interface.
-
-Required properties:
-- compatible: should contain "xlnx,zynqmp-pcap-fpga"
-
-Example for full FPGA configuration:
-
-	fpga-region0 {
-		compatible = "fpga-region";
-		fpga-mgr = <&zynqmp_pcap>;
-		#address-cells = <0x1>;
-		#size-cells = <0x1>;
-	};
-
-	firmware {
-		zynqmp_firmware: zynqmp-firmware {
-			compatible = "xlnx,zynqmp-firmware";
-			method = "smc";
-			zynqmp_pcap: pcap {
-				compatible = "xlnx,zynqmp-pcap-fpga";
-			};
-		};
-	};

Documentation/devicetree/bindings/fpga/xlnx,zynqmp-pcap-fpga.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/fpga/xlnx,zynqmp-pcap-fpga.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Zynq Ultrascale MPSoC FPGA Manager Device Tree Bindings
+
+maintainers:
+  - Nava kishore Manne <navam@xilinx.com>
+
+description: |
+  Device Tree Bindings for Zynq Ultrascale MPSoC FPGA Manager.
+  The ZynqMP SoC uses the PCAP (Processor Configuration Port) to
+  configure the Programmable Logic (PL). The configuration uses the
+  firmware interface.
+
+properties:
+  compatible:
+    const: xlnx,zynqmp-pcap-fpga
+
+required:
+  - compatible
+
+additionalProperties: false
+
+examples:
+  - |
+    firmware {
+      zynqmp_firmware: zynqmp-firmware {
+        zynqmp_pcap: pcap {
+          compatible = "xlnx,zynqmp-pcap-fpga";
+        };
+      };
+    };
+...

Documentation/devicetree/bindings/gpu/arm,mali-bifrost.yaml

@@ -20,6 +20,7 @@ properties:
           - mediatek,mt8183-mali
           - realtek,rtd1619-mali
           - rockchip,px30-mali
+          - rockchip,rk3568-mali
       - const: arm,mali-bifrost # Mali Bifrost GPU model/revision is fully discoverable
 
   reg:

Documentation/devicetree/bindings/hwmon/max1619.txt

-Bindings for MAX1619 Temperature Sensor
-
-Required properties:
-- compatible : "maxim,max1619"
-- reg        : I2C address, one of 0x18, 0x19, 0x1a, 0x29, 0x2a, 0x2b, 0x4c, or
-               0x4d, 0x4e
-
-Example:
-	temp@4c {
-		compatible = "maxim,max1619";
-		reg = <0x4c>;
-	};

Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.txt

-Broadcom iProc I2C controller
-
-Required properties:
-
-- compatible:
-    Must be "brcm,iproc-i2c" or "brcm,iproc-nic-i2c"
-
-- reg:
-    Define the base and range of the I/O address space that contain the iProc
-    I2C controller registers
-
-- clock-frequency:
-    This is the I2C bus clock. Need to be either 100000 or 400000
-
-- #address-cells:
-    Always 1 (for I2C addresses)
-
-- #size-cells:
-    Always 0
-
-Optional properties:
-
-- interrupts:
-    Should contain the I2C interrupt. For certain revisions of the I2C
-    controller, I2C interrupt is unwired to the interrupt controller. In such
-    case, this property should be left unspecified, and driver will fall back
-    to polling mode
-
-- brcm,ape-hsls-addr-mask:
-    Required for "brcm,iproc-nic-i2c". Host view of address mask into the
-    'APE' co-processor. Value must be unsigned, 32-bit
-
-Example:
-	i2c0: i2c@18008000 {
-		compatible = "brcm,iproc-i2c";
-		reg = <0x18008000 0x100>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
-		clock-frequency = <100000>;
-
-		codec: wm8750@1a {
-			compatible = "wlf,wm8750";
-			reg = <0x1a>;
-		};
-	};

Documentation/devicetree/bindings/i2c/brcm,iproc-i2c.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/brcm,iproc-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Broadcom iProc I2C controller
+
+maintainers:
+  - Rafał Miłecki <rafal@milecki.pl>
+
+properties:
+  compatible:
+    enum:
+      - brcm,iproc-i2c
+      - brcm,iproc-nic-i2c
+
+  reg:
+    maxItems: 1
+
+  clock-frequency:
+    enum: [ 100000, 400000 ]
+
+  interrupts:
+    description: |
+      Should contain the I2C interrupt. For certain revisions of the I2C
+      controller, I2C interrupt is unwired to the interrupt controller. In such
+      case, this property should be left unspecified, and driver will fall back
+      to polling mode
+    maxItems: 1
+
+  brcm,ape-hsls-addr-mask:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: Host view of address mask into the 'APE' co-processor
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: brcm,iproc-nic-i2c
+    then:
+      required:
+        - brcm,ape-hsls-addr-mask
+
+unevaluatedProperties: false
+
+required:
+  - reg
+  - clock-frequency
+  - '#address-cells'
+  - '#size-cells'
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    i2c@18008000 {
+        compatible = "brcm,iproc-i2c";
+        reg = <0x18008000 0x100>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+        interrupts = <GIC_SPI 85 IRQ_TYPE_NONE>;
+        clock-frequency = <100000>;
+
+        wm8750@1a {
+            compatible = "wlf,wm8750";
+            reg = <0x1a>;
+        };
+    };

Documentation/devicetree/bindings/i2c/ti,omap4-i2c.yaml

@@ -72,11 +72,11 @@ additionalProperties: false
 if:
   properties:
     compatible:
-      oneOf:
-        - const: ti,omap2420-i2c
-        - const: ti,omap2430-i2c
-        - const: ti,omap3-i2c
-        - const: ti,omap4-i2c
+      enum:
+        - ti,omap2420-i2c
+        - ti,omap2430-i2c
+        - ti,omap3-i2c
+        - ti,omap4-i2c
 
 then:
   properties:

Documentation/devicetree/bindings/interrupt-controller/loongson,liointc.yaml

@@ -19,10 +19,10 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: loongson,liointc-1.0
-      - const: loongson,liointc-1.0a
-      - const: loongson,liointc-2.0
+    enum:
+      - loongson,liointc-1.0
+      - loongson,liointc-1.0a
+      - loongson,liointc-2.0
 
   reg:
     minItems: 1

Documentation/devicetree/bindings/interrupt-controller/samsung,exynos4210-combiner.txt

-* Samsung Exynos Interrupt Combiner Controller
-
-Samsung's Exynos4 architecture includes a interrupt combiner controller which
-can combine interrupt sources as a group and provide a single interrupt request
-for the group. The interrupt request from each group are connected to a parent
-interrupt controller, such as GIC in case of Exynos4210.
-
-The interrupt combiner controller consists of multiple combiners. Up to eight
-interrupt sources can be connected to a combiner. The combiner outputs one
-combined interrupt for its eight interrupt sources. The combined interrupt
-is usually connected to a parent interrupt controller.
-
-A single node in the device tree is used to describe the interrupt combiner
-controller module (which includes multiple combiners). A combiner in the
-interrupt controller module shares config/control registers with other
-combiners. For example, a 32-bit interrupt enable/disable config register
-can accommodate up to 4 interrupt combiners (with each combiner supporting
-up to 8 interrupt sources).
-
-Required properties:
-- compatible: should be "samsung,exynos4210-combiner".
-- interrupt-controller: Identifies the node as an interrupt controller.
-- #interrupt-cells: should be <2>. The meaning of the cells are
-	* First Cell: Combiner Group Number.
-	* Second Cell: Interrupt number within the group.
-- reg: Base address and size of interrupt combiner registers.
-- interrupts: The list of interrupts generated by the combiners which are then
-    connected to a parent interrupt controller. The format of the interrupt
-    specifier depends in the interrupt parent controller.
-
-Optional properties:
-- samsung,combiner-nr: The number of interrupt combiners supported. If this
-  property is not specified, the default number of combiners is assumed
-  to be 16.
-
-
-Example:
-
-	The following is a an example from the Exynos4210 SoC dtsi file.
-
-	combiner:interrupt-controller@10440000 {
-		compatible = "samsung,exynos4210-combiner";
-		interrupt-controller;
-		#interrupt-cells = <2>;
-		reg = <0x10440000 0x1000>;
-		interrupts = <0 0 0>, <0 1 0>, <0 2 0>, <0 3 0>,
-			     <0 4 0>, <0 5 0>, <0 6 0>, <0 7 0>,
-			     <0 8 0>, <0 9 0>, <0 10 0>, <0 11 0>,
-			     <0 12 0>, <0 13 0>, <0 14 0>, <0 15 0>;
-	};

Documentation/devicetree/bindings/interrupt-controller/samsung,exynos4210-combiner.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interrupt-controller/samsung,exynos4210-combiner.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC Interrupt Combiner Controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+  Samsung's Exynos4 architecture includes a interrupt combiner controller which
+  can combine interrupt sources as a group and provide a single interrupt
+  request for the group. The interrupt request from each group are connected to
+  a parent interrupt controller, such as GIC in case of Exynos4210.
+
+  The interrupt combiner controller consists of multiple combiners. Up to eight
+  interrupt sources can be connected to a combiner. The combiner outputs one
+  combined interrupt for its eight interrupt sources. The combined interrupt is
+  usually connected to a parent interrupt controller.
+
+  A single node in the device tree is used to describe the interrupt combiner
+  controller module (which includes multiple combiners). A combiner in the
+  interrupt controller module shares config/control registers with other
+  combiners. For example, a 32-bit interrupt enable/disable config register can
+  accommodate up to 4 interrupt combiners (with each combiner supporting up to
+  8 interrupt sources).
+
+allOf:
+  - $ref: /schemas/interrupt-controller.yaml#
+
+properties:
+  compatible:
+    const: samsung,exynos4210-combiner
+
+  interrupt-controller: true
+
+  interrupts:
+    minItems: 8
+    maxItems: 32
+
+  "#interrupt-cells":
+    description: |
+      The meaning of the cells are:
+        * First Cell: Combiner Group Number.
+        * Second Cell: Interrupt number within the group.
+    const: 2
+
+  reg:
+    maxItems: 1
+
+  samsung,combiner-nr:
+    description: |
+      The number of interrupt combiners supported.  Should match number
+      of interrupts set in "interrupts" property.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 8
+    maximum: 32
+    default: 16
+
+required:
+  - compatible
+  - interrupt-controller
+  - interrupts
+  - "#interrupt-cells"
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    interrupt-controller@10440000 {
+        compatible = "samsung,exynos4210-combiner";
+        interrupt-controller;
+        #interrupt-cells = <2>;
+        reg = <0x10440000 0x1000>;
+        interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>,
+                     <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>;
+    };

Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml

@@ -46,7 +46,7 @@ properties:
                               AM437x family of SoCs,
                               AM57xx family of SoCs
                               66AK2G family of SoCs
-      Use "ti,icssg-intc" for K3 AM65x & J721E family of SoCs
+      Use "ti,icssg-intc" for K3 AM65x, J721E and AM64x family of SoCs
 
   reg:
     maxItems: 1
@@ -95,6 +95,8 @@ properties:
             - AM65x and J721E SoCs have "host_intr5", "host_intr6" and
               "host_intr7" interrupts connected to MPU, and other ICSSG
               instances.
+            - AM64x SoCs have all the 8 host interrupts connected to various
+              other SoC entities
 
 required:
   - compatible

Documentation/devicetree/bindings/media/atmel,isc.yaml

@@ -44,7 +44,8 @@ properties:
     const: isc-mck
 
   port:
-    $ref: /schemas/graph.yaml#/properties/port
+    $ref: /schemas/graph.yaml#/$defs/port-base
+    unevaluatedProperties: false
     description:
       Input port node, single endpoint describing the input pad.
 

Documentation/devicetree/bindings/media/i2c/mipi-ccs.yaml

@@ -83,10 +83,10 @@ properties:
           link-frequencies: true
           data-lanes: true
           bus-type:
-            oneOf:
-              - const: 1 # CSI-2 C-PHY
-              - const: 3 # CCP2
-              - const: 4 # CSI-2 D-PHY
+            enum:
+              - 1 # CSI-2 C-PHY
+              - 3 # CCP2
+              - 4 # CSI-2 D-PHY
 
         required:
           - link-frequencies

Documentation/devicetree/bindings/media/microchip,xisc.yaml

@@ -52,7 +52,7 @@ properties:
       of the data and clock lines.
 
   port:
-    $ref: /schemas/graph.yaml#/properties/port
+    $ref: /schemas/graph.yaml#/$defs/port-base
     description:
       Input port node, single endpoint describing the input pad.
 

Documentation/devicetree/bindings/media/nxp,imx7-mipi-csi2.yaml

@@ -200,8 +200,6 @@ examples:
         clock-names = "pclk", "wrap", "phy", "axi";
         power-domains = <&mipi_pd>;
 
-        status = "disabled";
-
         ports {
             #address-cells = <1>;
             #size-cells = <0>;

Documentation/devicetree/bindings/media/renesas,drif.yaml

@@ -96,7 +96,7 @@ properties:
       Indicates that the channel acts as primary among the bonded channels.
 
   port:
-    $ref: /schemas/graph.yaml#/properties/port
+    $ref: /schemas/graph.yaml#/$defs/port-base
     unevaluatedProperties: false
     description:
       Child port node corresponding to the data input. The port node must
@@ -242,7 +242,6 @@ examples:
                     power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;
                     resets = <&cpg 513>;
                     renesas,bonding = <&drif11>;
-                    status = "disabled";
             };
 
             drif11: rif@e6f70000 {

Documentation/devicetree/bindings/memory-controllers/ath79-ddr-controller.txt

-Binding for Qualcomm  Atheros AR7xxx/AR9xxx DDR controller
-
-The DDR controller of the AR7xxx and AR9xxx families provides an interface
-to flush the FIFO between various devices and the DDR. This is mainly used
-by the IRQ controller to flush the FIFO before running the interrupt handler
-of such devices.
-
-Required properties:
-
-- compatible: has to be "qca,<soc-type>-ddr-controller",
-  "qca,[ar7100|ar7240]-ddr-controller" as fallback.
-  On SoC with PCI support "qca,ar7100-ddr-controller" should be used as
-  fallback, otherwise "qca,ar7240-ddr-controller" should be used.
-- reg: Base address and size of the controller's memory area
-- #qca,ddr-wb-channel-cells: Specifies the number of cells needed to encode
-			     the write buffer channel index, should be 1.
-
-Example:
-
-	ddr_ctrl: memory-controller@18000000 {
-		compatible = "qca,ar9132-ddr-controller",
-				"qca,ar7240-ddr-controller";
-		reg = <0x18000000 0x100>;
-
-		#qca,ddr-wb-channel-cells = <1>;
-	};
-
-	...
-
-	interrupt-controller {
-		...
-		qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
-		qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
-					<&ddr_ctrl 0>, <&ddr_ctrl 1>;
-	};

Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt

-DDR PHY Front End (DPFE) for Broadcom STB
-=========================================
-
-DPFE and the DPFE firmware provide an interface for the host CPU to
-communicate with the DCPU, which resides inside the DDR PHY.
-
-There are three memory regions for interacting with the DCPU. These are
-specified in a single reg property.
-
-Required properties:
-  - compatible: must be "brcm,bcm7271-dpfe-cpu", "brcm,bcm7268-dpfe-cpu"
-    or "brcm,dpfe-cpu"
-  - reg: must reference three register ranges
-      - start address and length of the DCPU register space
-      - start address and length of the DCPU data memory space
-      - start address and length of the DCPU instruction memory space
-  - reg-names: must contain "dpfe-cpu", "dpfe-dmem", and "dpfe-imem";
-        they must be in the same order as the register declarations
-
-Example:
-	dpfe_cpu0: dpfe-cpu@f1132000 {
-		compatible = "brcm,bcm7271-dpfe-cpu", "brcm,dpfe-cpu";
-		reg =  <0xf1132000 0x180
-			0xf1134000 0x1000
-			0xf1138000 0x4000>;
-		reg-names = "dpfe-cpu", "dpfe-dmem", "dpfe-imem";
-	};

Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/brcm,dpfe-cpu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: DDR PHY Front End (DPFE) for Broadcom STB
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Markus Mayer <mmayer@broadcom.com>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - brcm,bcm7271-dpfe-cpu
+          - brcm,bcm7268-dpfe-cpu
+      - const: brcm,dpfe-cpu
+
+  reg:
+    items:
+      - description: DCPU register space
+      - description: DCPU data memory space
+      - description: DCPU instruction memory space
+
+  reg-names:
+    items:
+      - const: dpfe-cpu
+      - const: dpfe-dmem
+      - const: dpfe-imem
+
+required:
+  - compatible
+  - reg
+  - reg-names
+
+additionalProperties: false
+
+examples:
+  - |
+    dpfe-cpu@f1132000 {
+        compatible = "brcm,bcm7271-dpfe-cpu", "brcm,dpfe-cpu";
+        reg = <0xf1132000 0x180>,
+              <0xf1134000 0x1000>,
+              <0xf1138000 0x4000>;
+        reg-names = "dpfe-cpu", "dpfe-dmem", "dpfe-imem";
+    };

Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt

-* Exynos5422 frequency and voltage scaling for Dynamic Memory Controller device
-
-The Samsung Exynos5422 SoC has DMC (Dynamic Memory Controller) to which the DRAM
-memory chips are connected. The driver is to monitor the controller in runtime
-and switch frequency and voltage. To monitor the usage of the controller in
-runtime, the driver uses the PPMU (Platform Performance Monitoring Unit), which
-is able to measure the current load of the memory.
-When 'userspace' governor is used for the driver, an application is able to
-switch the DMC and memory frequency.
-
-Required properties for DMC device for Exynos5422:
-- compatible: Should be "samsung,exynos5422-dmc".
-- clocks : list of clock specifiers, must contain an entry for each
-  required entry in clock-names for CLK_FOUT_SPLL, CLK_MOUT_SCLK_SPLL,
-  CLK_FF_DOUT_SPLL2, CLK_FOUT_BPLL, CLK_MOUT_BPLL, CLK_SCLK_BPLL,
-  CLK_MOUT_MX_MSPLL_CCORE, CLK_MOUT_MX_MSPLL_CCORE_PHY, CLK_MOUT_MCLK_CDREX,
-- clock-names : should include "fout_spll", "mout_sclk_spll", "ff_dout_spll2",
-  "fout_bpll", "mout_bpll", "sclk_bpll", "mout_mx_mspll_ccore",
-  "mout_mclk_cdrex"  entries
-- devfreq-events : phandles for PPMU devices connected to this DMC.
-- vdd-supply : phandle for voltage regulator which is connected.
-- reg : registers of two CDREX controllers.
-- operating-points-v2 : phandle for OPPs described in v2 definition.
-- device-handle : phandle of the connected DRAM memory device. For more
-	information please refer to documentation file:
-	Documentation/devicetree/bindings/ddr/lpddr3.txt
-- devfreq-events : phandles of the PPMU events used by the controller.
-- samsung,syscon-clk : phandle of the clock register set used by the controller,
-	these registers are used for enabling a 'pause' feature and are not
-	exposed by clock framework but they must be used in a safe way.
-	The register offsets are in the driver code and specyfic for this SoC
-	type.
-
-Optional properties for DMC device for Exynos5422:
-- interrupt-parent : The parent interrupt controller.
-- interrupts : Contains the IRQ line numbers for the DMC internal performance
-  event counters in DREX0 and DREX1 channels. Align with specification of the
-  interrupt line(s) in the interrupt-parent controller.
-- interrupt-names : IRQ names "drex_0" and "drex_1", the order should be the
-  same as in the 'interrupts' list above.
-
-Example:
-
-	ppmu_dmc0_0: ppmu@10d00000 {
-		compatible = "samsung,exynos-ppmu";
-		reg = <0x10d00000 0x2000>;
-		clocks = <&clock CLK_PCLK_PPMU_DREX0_0>;
-		clock-names = "ppmu";
-		events {
-			ppmu_event_dmc0_0: ppmu-event3-dmc0_0 {
-				event-name = "ppmu-event3-dmc0_0";
-			};
-		};
-	};
-
-	dmc: memory-controller@10c20000 {
-		compatible = "samsung,exynos5422-dmc";
-		reg = <0x10c20000 0x10000>, <0x10c30000 0x10000>;
-		clocks = <&clock CLK_FOUT_SPLL>,
-			 <&clock CLK_MOUT_SCLK_SPLL>,
-			 <&clock CLK_FF_DOUT_SPLL2>,
-			 <&clock CLK_FOUT_BPLL>,
-			 <&clock CLK_MOUT_BPLL>,
-			 <&clock CLK_SCLK_BPLL>,
-			 <&clock CLK_MOUT_MX_MSPLL_CCORE>,
-			 <&clock CLK_MOUT_MCLK_CDREX>;
-		clock-names = "fout_spll",
-			      "mout_sclk_spll",
-			      "ff_dout_spll2",
-			      "fout_bpll",
-			      "mout_bpll",
-			      "sclk_bpll",
-			      "mout_mx_mspll_ccore",
-			      "mout_mclk_cdrex";
-		operating-points-v2 = <&dmc_opp_table>;
-		devfreq-events = <&ppmu_event3_dmc0_0>,	<&ppmu_event3_dmc0_1>,
-				 <&ppmu_event3_dmc1_0>, <&ppmu_event3_dmc1_1>;
-		device-handle = <&samsung_K3QF2F20DB>;
-		vdd-supply = <&buck1_reg>;
-		samsung,syscon-clk = <&clock>;
-		interrupt-parent = <&combiner>;
-		interrupts = <16 0>, <16 1>;
-		interrupt-names = "drex_0", "drex_1";
-	};

Documentation/devicetree/bindings/memory-controllers/marvell,mvebu-sdram-controller.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/marvell,mvebu-sdram-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell MVEBU SDRAM controller
+
+maintainers:
+  - Jan Luebbe <jlu@pengutronix.de>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+properties:
+  compatible:
+    const: marvell,armada-xp-sdram-controller
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@1400 {
+        compatible = "marvell,armada-xp-sdram-controller";
+        reg = <0x1400 0x500>;
+    };

Documentation/devicetree/bindings/memory-controllers/mvebu-sdram-controller.txt

-Device Tree bindings for MVEBU SDRAM controllers
-
-The Marvell EBU SoCs all have a SDRAM controller. The SDRAM controller
-differs from one SoC variant to another, but they also share a number
-of commonalities.
-
-For now, this Device Tree binding documentation only documents the
-Armada XP SDRAM controller.
-
-Required properties:
-
- - compatible: for Armada XP, "marvell,armada-xp-sdram-controller"
- - reg: a resource specifier for the register space, which should
-   include all SDRAM controller registers as per the datasheet.
-
-Example:
-
-sdramc@1400 {
-	compatible = "marvell,armada-xp-sdram-controller";
-	reg = <0x1400 0x500>;
-};

Documentation/devicetree/bindings/memory-controllers/qca,ath79-ddr-controller.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/qca,ath79-ddr-controller.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Atheros AR7xxx/AR9xxx DDR controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+  The DDR controller of the AR7xxx and AR9xxx families provides an interface to
+  flush the FIFO between various devices and the DDR. This is mainly used by
+  the IRQ controller to flush the FIFO before running the interrupt handler of
+  such devices.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - const: qca,ar9132-ddr-controller
+          - const: qca,ar7240-ddr-controller
+      - items:
+          - enum:
+              - qca,ar7100-ddr-controller
+              - qca,ar7240-ddr-controller
+
+  "#qca,ddr-wb-channel-cells":
+    description: |
+      Specifies the number of cells needed to encode the write buffer channel
+      index.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    const: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - "#qca,ddr-wb-channel-cells"
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    ddr_ctrl: memory-controller@18000000 {
+        compatible = "qca,ar9132-ddr-controller",
+                     "qca,ar7240-ddr-controller";
+        reg = <0x18000000 0x100>;
+
+        #qca,ddr-wb-channel-cells = <1>;
+    };
+
+    interrupt-controller {
+        // ...
+        qca,ddr-wb-channel-interrupts = <2>, <3>, <4>, <5>;
+        qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>,
+                              <&ddr_ctrl 0>, <&ddr_ctrl 1>;
+    };

Documentation/devicetree/bindings/memory-controllers/renesas,h8300-bsc.txt

-* H8/300 bus controller
-
-Required properties:
-  - compatible: Must be "renesas,h8300-bsc".
-  - reg: Base address and length of BSC registers.
-
-Example.
-	bsc: memory-controller@fee01e {
-		compatible = "renesas,h8300h-bsc", "renesas,h8300-bsc";
-		reg = <0xfee01e 8>;
-	};
-

Documentation/devicetree/bindings/memory-controllers/renesas,h8300-bsc.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/renesas,h8300-bsc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: H8/300 bus controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Yoshinori Sato <ysato@users.sourceforge.jp>
+
+properties:
+  compatible:
+    items:
+      - enum:
+          - renesas,h8300h-bsc
+          - renesas,h8s-bsc
+      - const: renesas,h8300-bsc
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@fee01e {
+        compatible = "renesas,h8300h-bsc", "renesas,h8300-bsc";
+        reg = <0xfee01e 8>;
+    };

Documentation/devicetree/bindings/memory-controllers/renesas,rpc-if.yaml

@@ -61,12 +61,23 @@ patternProperties:
     type: object
     properties:
       compatible:
-        enum:
-          - cfi-flash
-          - jedec,spi-nor
+        contains:
+          enum:
+            - cfi-flash
+            - jedec,spi-nor
 
 unevaluatedProperties: false
 
+required:
+  - compatible
+  - reg
+  - reg-names
+  - clocks
+  - power-domains
+  - resets
+  - '#address-cells'
+  - '#size-cells'
+
 examples:
   - |
     #include <dt-bindings/clock/renesas-cpg-mssr.h>

Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/samsung,exynos5422-dmc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: |
+  Samsung Exynos5422 SoC frequency and voltage scaling for Dynamic Memory
+  Controller device
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Lukasz Luba <lukasz.luba@arm.com>
+
+description: |
+  The Samsung Exynos5422 SoC has DMC (Dynamic Memory Controller) to which the
+  DRAM memory chips are connected. The driver is to monitor the controller in
+  runtime and switch frequency and voltage. To monitor the usage of the
+  controller in runtime, the driver uses the PPMU (Platform Performance
+  Monitoring Unit), which is able to measure the current load of the memory.
+  When 'userspace' governor is used for the driver, an application is able to
+  switch the DMC and memory frequency.
+
+properties:
+  compatible:
+    items:
+      - const: samsung,exynos5422-dmc
+
+  clock-names:
+    items:
+      - const: fout_spll
+      - const: mout_sclk_spll
+      - const: ff_dout_spll2
+      - const: fout_bpll
+      - const: mout_bpll
+      - const: sclk_bpll
+      - const: mout_mx_mspll_ccore
+      - const: mout_mclk_cdrex
+
+  clocks:
+    minItems: 8
+    maxItems: 8
+
+  devfreq-events:
+    $ref: '/schemas/types.yaml#/definitions/phandle-array'
+    minItems: 1
+    maxItems: 16
+    description: phandles of the PPMU events used by the controller.
+
+  device-handle:
+    $ref: '/schemas/types.yaml#/definitions/phandle'
+    description: |
+      phandle of the connected DRAM memory device. For more information please
+      refer to documentation file: Documentation/devicetree/bindings/ddr/lpddr3.txt
+
+  operating-points-v2: true
+
+  interrupts:
+    items:
+      - description: DMC internal performance event counters in DREX0
+      - description: DMC internal performance event counters in DREX1
+
+  interrupt-names:
+    items:
+      - const: drex_0
+      - const: drex_1
+
+  reg:
+    items:
+      - description: registers of DREX0
+      - description: registers of DREX1
+
+  samsung,syscon-clk:
+    $ref: '/schemas/types.yaml#/definitions/phandle'
+    description: |
+      Phandle of the clock register set used by the controller, these registers
+      are used for enabling a 'pause' feature and are not exposed by clock
+      framework but they must be used in a safe way.  The register offsets are
+      in the driver code and specyfic for this SoC type.
+
+  vdd-supply: true
+
+required:
+  - compatible
+  - clock-names
+  - clocks
+  - devfreq-events
+  - device-handle
+  - reg
+  - samsung,syscon-clk
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5420.h>
+    ppmu_dmc0_0: ppmu@10d00000 {
+        compatible = "samsung,exynos-ppmu";
+        reg = <0x10d00000 0x2000>;
+        clocks = <&clock CLK_PCLK_PPMU_DREX0_0>;
+        clock-names = "ppmu";
+        events {
+            ppmu_event_dmc0_0: ppmu-event3-dmc0-0 {
+                event-name = "ppmu-event3-dmc0_0";
+            };
+        };
+    };
+
+    memory-controller@10c20000 {
+        compatible = "samsung,exynos5422-dmc";
+        reg = <0x10c20000 0x10000>, <0x10c30000 0x10000>;
+        clocks = <&clock CLK_FOUT_SPLL>,
+                 <&clock CLK_MOUT_SCLK_SPLL>,
+                 <&clock CLK_FF_DOUT_SPLL2>,
+                 <&clock CLK_FOUT_BPLL>,
+                 <&clock CLK_MOUT_BPLL>,
+                 <&clock CLK_SCLK_BPLL>,
+                 <&clock CLK_MOUT_MX_MSPLL_CCORE>,
+                 <&clock CLK_MOUT_MCLK_CDREX>;
+        clock-names = "fout_spll",
+                      "mout_sclk_spll",
+                      "ff_dout_spll2",
+                      "fout_bpll",
+                      "mout_bpll",
+                      "sclk_bpll",
+                      "mout_mx_mspll_ccore",
+                      "mout_mclk_cdrex";
+        operating-points-v2 = <&dmc_opp_table>;
+        devfreq-events = <&ppmu_event3_dmc0_0>,	<&ppmu_event3_dmc0_1>,
+                         <&ppmu_event3_dmc1_0>, <&ppmu_event3_dmc1_1>;
+        device-handle = <&samsung_K3QF2F20DB>;
+        vdd-supply = <&buck1_reg>;
+        samsung,syscon-clk = <&clock>;
+        interrupt-parent = <&combiner>;
+        interrupts = <16 0>, <16 1>;
+        interrupt-names = "drex_0", "drex_1";
+    };

Documentation/devicetree/bindings/memory-controllers/synopsys,ddrc-ecc.yaml

+# SPDX-License-Identifier: GPL-2.0-only
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/synopsys,ddrc-ecc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys IntelliDDR Multi Protocol memory controller
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Manish Narani <manish.narani@xilinx.com>
+  - Michal Simek <michal.simek@xilinx.com>
+
+description: |
+  The ZynqMP DDR ECC controller has an optional ECC support in 64-bit and
+  32-bit bus width configurations.
+
+  The Zynq DDR ECC controller has an optional ECC support in half-bus width
+  (16-bit) configuration.
+
+  These both ECC controllers correct single bit ECC errors and detect double bit
+  ECC errors.
+
+properties:
+  compatible:
+    enum:
+      - xlnx,zynq-ddrc-a05
+      - xlnx,zynqmp-ddrc-2.40a
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: xlnx,zynqmp-ddrc-2.40a
+    then:
+      required:
+        - interrupts
+    else:
+      properties:
+        interrupts: false
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@f8006000 {
+        compatible = "xlnx,zynq-ddrc-a05";
+        reg = <0xf8006000 0x1000>;
+    };
+
+  - |
+    axi {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        memory-controller@fd070000 {
+            compatible = "xlnx,zynqmp-ddrc-2.40a";
+            reg = <0x0 0xfd070000 0x0 0x30000>;
+            interrupt-parent = <&gic>;
+            interrupts = <0 112 4>;
+        };
+    };

Documentation/devicetree/bindings/memory-controllers/synopsys.txt

-Binding for Synopsys IntelliDDR Multi Protocol Memory Controller
-
-The ZynqMP DDR ECC controller has an optional ECC support in 64-bit and 32-bit
-bus width configurations.
-
-The Zynq DDR ECC controller has an optional ECC support in half-bus width
-(16-bit) configuration.
-
-These both ECC controllers correct single bit ECC errors and detect double bit
-ECC errors.
-
-Required properties:
- - compatible: One of:
-	- 'xlnx,zynq-ddrc-a05' : Zynq DDR ECC controller
-	- 'xlnx,zynqmp-ddrc-2.40a' : ZynqMP DDR ECC controller
- - reg: Should contain DDR controller registers location and length.
-
-Required properties for "xlnx,zynqmp-ddrc-2.40a":
- - interrupts: Property with a value describing the interrupt number.
-
-Example:
-	memory-controller@f8006000 {
-		compatible = "xlnx,zynq-ddrc-a05";
-		reg = <0xf8006000 0x1000>;
-	};
-
-	mc: memory-controller@fd070000 {
-		compatible = "xlnx,zynqmp-ddrc-2.40a";
-		reg = <0x0 0xfd070000 0x0 0x30000>;
-		interrupt-parent = <&gic>;
-		interrupts = <0 112 4>;
-	};

Documentation/devicetree/bindings/memory-controllers/ti,da8xx-ddrctl.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/memory-controllers/ti,da8xx-ddrctl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments da8xx DDR2/mDDR memory controller
+
+maintainers:
+  - Bartosz Golaszewski <bgolaszewski@baylibre.com>
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+
+description: |
+  Documentation:
+    OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
+
+properties:
+  compatible:
+    const: ti,da850-ddr-controller
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    memory-controller@b0000000 {
+        compatible = "ti,da850-ddr-controller";
+        reg = <0xb0000000 0xe8>;
+    };

Documentation/devicetree/bindings/memory-controllers/ti-da8xx-ddrctl.txt

-* Device tree bindings for Texas Instruments da8xx DDR2/mDDR memory controller
-
-The DDR2/mDDR memory controller present on Texas Instruments da8xx SoCs features
-a set of registers which allow to tweak the controller's behavior.
-
-Documentation:
-OMAP-L138 (DA850) - http://www.ti.com/lit/ug/spruh82c/spruh82c.pdf
-
-Required properties:
-
-- compatible:		"ti,da850-ddr-controller" - for da850 SoC based boards
-- reg:			a tuple containing the base address of the memory
-			controller and the size of the memory area to map
-
-Example for da850 shown below.
-
-ddrctl {
-	compatible = "ti,da850-ddr-controller";
-	reg = <0xb0000000 0xe8>;
-};

Documentation/devicetree/bindings/mfd/ti,lp87565-q1.yaml

@@ -11,9 +11,9 @@ maintainers:
 
 properties:
   compatible:
-    oneOf:
-      - const: ti,lp87565
-      - const: ti,lp87565-q1
+    enum:
+      - ti,lp87565
+      - ti,lp87565-q1
 
   reg:
     description: I2C slave address

Documentation/devicetree/bindings/misc/eeprom-93xx46.txt

-EEPROMs (SPI) compatible with Microchip Technology 93xx46 family.
-
-Required properties:
-- compatible : shall be one of:
-    "atmel,at93c46"
-    "atmel,at93c46d"
-    "atmel,at93c56"
-    "atmel,at93c66"
-    "eeprom-93xx46"
-    "microchip,93lc46b"
-- data-size : number of data bits per word (either 8 or 16)
-
-Optional properties:
-- read-only : parameter-less property which disables writes to the EEPROM
-- select-gpios : if present, specifies the GPIO that will be asserted prior to
-  each access to the EEPROM (e.g. for SPI bus multiplexing)
-
-Property rules described in Documentation/devicetree/bindings/spi/spi-bus.txt
-apply.  In particular, "reg" and "spi-max-frequency" properties must be given.
-
-Example:
-	eeprom@0 {
-		compatible = "eeprom-93xx46";
-		reg = <0>;
-		spi-max-frequency = <1000000>;
-		spi-cs-high;
-		data-size = <8>;
-		select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
-	};

Documentation/devicetree/bindings/misc/eeprom-93xx46.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/misc/eeprom-93xx46.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip 93xx46 SPI compatible EEPROM family dt bindings
+
+maintainers:
+  - Cory Tusar <cory.tusar@pid1solutions.com>
+
+properties:
+  compatible:
+    enum:
+      - atmel,at93c46
+      - atmel,at93c46d
+      - atmel,at93c56
+      - atmel,at93c66
+      - eeprom-93xx46
+      - microchip,93lc46b
+
+  data-size:
+    description: number of data bits per word
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [8, 16]
+
+  reg:
+    description: chip select of EEPROM
+    maxItems: 1
+
+  spi-max-frequency: true
+  spi-cs-high: true
+
+  read-only:
+    description:
+      parameter-less property which disables writes to the EEPROM
+    type: boolean
+
+  select-gpios:
+    description:
+      specifies the GPIO that needs to be asserted prior to each access
+      of EEPROM (e.g. for SPI bus multiplexing)
+    maxItems: 1
+
+
+required:
+  - compatible
+  - reg
+  - data-size
+  - spi-max-frequency
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    spi {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      eeprom@0 {
+        compatible = "eeprom-93xx46";
+        reg = <0>;
+        spi-max-frequency = <1000000>;
+        spi-cs-high;
+        data-size = <8>;
+        select-gpios = <&gpio4 4 GPIO_ACTIVE_HIGH>;
+      };
+    };

Documentation/devicetree/bindings/mtd/gpmc-nor.txt

@@ -10,7 +10,7 @@ Documentation/devicetree/bindings/memory-controllers/omap-gpmc.txt
 Required properties:
 - bank-width: 		Width of NOR flash in bytes. GPMC supports 8-bit and
 			16-bit devices and so must be either 1 or 2 bytes.
-- compatible:		Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- compatible:		Documentation/devicetree/bindings/mtd/mtd-physmap.yaml
 - gpmc,cs-on-ns:		Chip-select assertion time
 - gpmc,cs-rd-off-ns:	Chip-select de-assertion time for reads
 - gpmc,cs-wr-off-ns:	Chip-select de-assertion time for writes
@@ -21,7 +21,7 @@ Required properties:
 - gpmc,access-ns:	Start cycle to first data capture (read access)
 - gpmc,rd-cycle-ns:	Total read cycle time
 - gpmc,wr-cycle-ns:	Total write cycle time
-- linux,mtd-name:	Documentation/devicetree/bindings/mtd/mtd-physmap.txt
+- linux,mtd-name:	Documentation/devicetree/bindings/mtd/mtd-physmap.yaml
 - reg:			Chip-select, base address (relative to chip-select)
 			and size of NOR flash. Note that base address will be
 			typically 0 as this is the start of the chip-select.

Documentation/devicetree/bindings/mtd/mtd-physmap.yaml

@@ -23,6 +23,7 @@ properties:
               - amd,s29gl256n
               - amd,s29gl512n
               - arm,versatile-flash
+              - arm,vexpress-flash
               - cortina,gemini-flash
               - cypress,hyperflash
               - ge,imp3a-firmware-mirror

Documentation/devicetree/bindings/net/intel,dwmac-plat.yaml

@@ -116,7 +116,6 @@ examples:
         snps,mtl-rx-config = <&mtl_rx_setup>;
         snps,mtl-tx-config = <&mtl_tx_setup>;
         snps,tso;
-        status = "okay";
 
         mdio0 {
             #address-cells = <1>;

Documentation/devicetree/bindings/net/intel,ixp4xx-ethernet.yaml

@@ -71,7 +71,6 @@ examples:
     ethernet@c8009000 {
       compatible = "intel,ixp4xx-ethernet";
       reg = <0xc8009000 0x1000>;
-      status = "disabled";
       queue-rx = <&qmgr 4>;
       queue-txready = <&qmgr 21>;
       intel,npe-handle = <&npe 1>;
@@ -82,7 +81,6 @@ examples:
     ethernet@c800c000 {
       compatible = "intel,ixp4xx-ethernet";
       reg = <0xc800c000 0x1000>;
-      status = "disabled";
       queue-rx = <&qmgr 3>;
       queue-txready = <&qmgr 20>;
       intel,npe-handle = <&npe 2>;

Documentation/devicetree/bindings/net/micrel,ks8851.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/micrel,ks8851.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Micrel KS8851 Ethernet MAC (SPI and Parallel bus options)
+
+maintainers:
+  - Marek Vasut <marex@denx.de>
+
+properties:
+  compatible:
+    enum:
+      - micrel,ks8851      # SPI bus option
+      - micrel,ks8851-mll  # Parallel bus option
+
+  interrupts:
+    maxItems: 1
+
+  reg:
+    minItems: 1
+    items:
+      - description: SPI or Parallel bus hardware address
+      - description: Parallel bus command mode address
+
+  reset-gpios:
+    maxItems: 1
+    description:
+      The reset_n input pin
+
+  vdd-supply:
+    description: |
+      Analog 3.3V supply for Ethernet MAC
+
+  vdd-io-supply:
+    description: |
+      Digital 1.8V IO supply for Ethernet MAC
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+allOf:
+  - $ref: ethernet-controller.yaml#
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: micrel,ks8851
+    then:
+      properties:
+        reg:
+          maxItems: 1
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: micrel,ks8851-mll
+    then:
+      properties:
+        reg:
+          minItems: 2
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    /* SPI bus option */
+    spi {
+        #address-cells = <1>;
+        #size-cells = <0>;
+        ethernet@0 {
+            compatible = "micrel,ks8851";
+            reg = <0>;
+            interrupt-parent = <&msmgpio>;
+            interrupts = <90 8>;
+            vdd-supply = <&ext_l2>;
+            vdd-io-supply = <&pm8921_lvs6>;
+            reset-gpios = <&msmgpio 89 0>;
+        };
+    };
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    /* Parallel bus option */
+    memory-controller {
+        #address-cells = <2>;
+        #size-cells = <1>;
+        ethernet@1,0 {
+            compatible = "micrel,ks8851-mll";
+            reg = <1 0x0 0x2>, <1 0x2 0x20000>;
+            interrupt-parent = <&gpioc>;
+            interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
+        };
+    };

Documentation/devicetree/bindings/net/micrel-ks8851.txt

-Micrel KS8851 Ethernet mac (MLL)
-
-Required properties:
-- compatible = "micrel,ks8851-mll" of parallel interface
-- reg : 2 physical address and size of registers for data and command
-- interrupts : interrupt connection
-
-Micrel KS8851 Ethernet mac (SPI)
-
-Required properties:
-- compatible = "micrel,ks8851" or the deprecated "ks8851"
-- reg : chip select number
-- interrupts : interrupt connection
-
-Optional properties:
-- vdd-supply: analog 3.3V supply for Ethernet mac
-- vdd-io-supply: digital 1.8V IO supply for Ethernet mac
-- reset-gpios: reset_n input pin

Documentation/devicetree/bindings/net/mscc-phy-vsc8531.txt

@@ -67,7 +67,7 @@ Example:
                 compatible = "ethernet-phy-id0007.0570";
                 vsc8531,vddmac		= <3300>;
                 vsc8531,edge-slowdown	= <7>;
-                vsc8531,led-0-mode	= <LINK_1000_ACTIVITY>;
-                vsc8531,led-1-mode	= <LINK_100_ACTIVITY>;
+                vsc8531,led-0-mode	= <VSC8531_LINK_1000_ACTIVITY>;
+                vsc8531,led-1-mode	= <VSC8531_LINK_100_ACTIVITY>;
 		load-save-gpios		= <&gpio 10 GPIO_ACTIVE_HIGH>;
         };

Documentation/devicetree/bindings/net/nfc/samsung,s3fwrn5.yaml

@@ -90,14 +90,11 @@ examples:
   # UART example on Raspberry Pi
   - |
     uart0 {
-        status = "okay";
-
         nfc {
             compatible = "samsung,s3fwrn82";
 
             en-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>;
             wake-gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
 
-            status = "okay";
         };
     };

Documentation/devicetree/bindings/net/qca,ar71xx.yaml

@@ -101,8 +101,6 @@ examples:
 
         phy-mode = "gmii";
 
-        status = "disabled";
-
         fixed-link {
             speed = <1000>;
             full-duplex;
@@ -148,32 +146,24 @@ examples:
                         reg = <0x1>;
                         phy-handle = <&phy_port0>;
                         phy-mode = "internal";
-
-                        status = "disabled";
                     };
 
                     switch_port2: port@2 {
                         reg = <0x2>;
                         phy-handle = <&phy_port1>;
                         phy-mode = "internal";
-
-                        status = "disabled";
                     };
 
                     switch_port3: port@3 {
                         reg = <0x3>;
                         phy-handle = <&phy_port2>;
                         phy-mode = "internal";
-
-                        status = "disabled";
                     };
 
                     switch_port4: port@4 {
                         reg = <0x4>;
                         phy-handle = <&phy_port3>;
                         phy-mode = "internal";
-
-                        status = "disabled";
                     };
                 };
 
@@ -183,34 +173,29 @@ examples:
 
                     interrupt-parent = <&switch10>;
 
-                    phy_port0: phy@0 {
+                    phy_port0: ethernet-phy@0 {
                         reg = <0x0>;
                         interrupts = <0>;
-                        status = "disabled";
                     };
 
-                    phy_port1: phy@1 {
+                    phy_port1: ethernet-phy@1 {
                         reg = <0x1>;
                         interrupts = <0>;
-                        status = "disabled";
                     };
 
-                    phy_port2: phy@2 {
+                    phy_port2: ethernet-phy@2 {
                         reg = <0x2>;
                         interrupts = <0>;
-                        status = "disabled";
                     };
 
-                    phy_port3: phy@3 {
+                    phy_port3: ethernet-phy@3 {
                         reg = <0x3>;
                         interrupts = <0>;
-                        status = "disabled";
                     };
 
-                    phy_port4: phy@4 {
+                    phy_port4: ethernet-phy@4 {
                         reg = <0x4>;
                         interrupts = <0>;
-                        status = "disabled";
                     };
                 };
             };

Documentation/devicetree/bindings/net/realtek-bluetooth.yaml

@@ -17,10 +17,10 @@ description:
 
 properties:
   compatible:
-    oneOf:
-      - const: "realtek,rtl8723bs-bt"
-      - const: "realtek,rtl8723cs-bt"
-      - const: "realtek,rtl8822cs-bt"
+    enum:
+      - realtek,rtl8723bs-bt
+      - realtek,rtl8723cs-bt
+      - realtek,rtl8822cs-bt
 
   device-wake-gpios:
     maxItems: 1

Documentation/devicetree/bindings/net/renesas,etheravb.yaml

@@ -43,23 +43,20 @@ properties:
               - renesas,etheravb-r8a779a0     # R-Car V3U
           - const: renesas,etheravb-rcar-gen3 # R-Car Gen3 and RZ/G2
 
+      - items:
+          - enum:
+              - renesas,r9a07g044-gbeth # RZ/G2{L,LC}
+          - const: renesas,rzg2l-gbeth  # RZ/G2L
+
   reg: true
 
   interrupts: true
 
   interrupt-names: true
 
-  clocks:
-    minItems: 1
-    items:
-      - description: AVB functional clock
-      - description: Optional TXC reference clock
+  clocks: true
 
-  clock-names:
-    minItems: 1
-    items:
-      - const: fck
-      - const: refclk
+  clock-names: true
 
   iommus:
     maxItems: 1
@@ -145,14 +142,20 @@ allOf:
       properties:
         compatible:
           contains:
-            const: renesas,etheravb-rcar-gen2
+            enum:
+              - renesas,etheravb-rcar-gen2
+              - renesas,rzg2l-gbeth
     then:
       properties:
         interrupts:
-          maxItems: 1
+          minItems: 1
+          maxItems: 3
         interrupt-names:
+          minItems: 1
           items:
             - const: mux
+            - const: fil
+            - const: arp_ns
         rx-internal-delay-ps: false
     else:
       properties:
@@ -208,6 +211,36 @@ allOf:
         tx-internal-delay-ps:
           const: 2000
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            const: renesas,rzg2l-gbeth
+    then:
+      properties:
+        clocks:
+          items:
+            - description: Main clock
+            - description: Register access clock
+            - description: Reference clock for RGMII
+        clock-names:
+          items:
+            - const: axi
+            - const: chi
+            - const: refclk
+    else:
+      properties:
+        clocks:
+          minItems: 1
+          items:
+            - description: AVB functional clock
+            - description: Optional TXC reference clock
+        clock-names:
+          minItems: 1
+          items:
+            - const: fck
+            - const: refclk
+
 additionalProperties: false
 
 examples:

Documentation/devicetree/bindings/net/ti,k3-am654-cpsw-nuss.yaml

@@ -53,10 +53,10 @@ properties:
   "#size-cells": true
 
   compatible:
-    oneOf:
-      - const: ti,am654-cpsw-nuss
-      - const: ti,j721e-cpsw-nuss
-      - const: ti,am642-cpsw-nuss
+    enum:
+      - ti,am654-cpsw-nuss
+      - ti,j721e-cpsw-nuss
+      - ti,am642-cpsw-nuss
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/net/ti,k3-am654-cpts.yaml

@@ -45,9 +45,9 @@ properties:
     pattern: "^cpts@[0-9a-f]+$"
 
   compatible:
-    oneOf:
-      - const: ti,am65-cpts
-      - const: ti,j721e-cpts
+    enum:
+      - ti,am65-cpts
+      - ti,j721e-cpts
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/nvmem/nvmem.yaml

@@ -40,7 +40,7 @@ properties:
     maxItems: 1
 
 patternProperties:
-  "^.*@[0-9a-f]+$":
+  "@[0-9a-f]+(,[0-7])?$":
     type: object
 
     properties:

Documentation/devicetree/bindings/nvmem/socionext,uniphier-efuse.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/nvmem/socionext,uniphier-efuse.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Socionext UniPhier eFuse bindings
+
+maintainers:
+  - Keiji Hayashibara <hayashibara.keiji@socionext.com>
+  - Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
+
+allOf:
+  - $ref: "nvmem.yaml#"
+
+properties:
+  "#address-cells": true
+  "#size-cells": true
+
+  compatible:
+    const: socionext,uniphier-efuse
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    // The UniPhier eFuse should be a subnode of a "soc-glue" node.
+
+    soc-glue@5f900000 {
+        compatible = "simple-mfd";
+        #address-cells = <1>;
+        #size-cells = <1>;
+        ranges = <0x0 0x5f900000 0x2000>;
+
+        efuse@100 {
+            compatible = "socionext,uniphier-efuse";
+            reg = <0x100 0x28>;
+        };
+
+        efuse@200 {
+            compatible = "socionext,uniphier-efuse";
+            reg = <0x200 0x68>;
+            #address-cells = <1>;
+            #size-cells = <1>;
+
+            /* Data cells */
+            usb_rterm0: trim@54,4 {
+                reg = <0x54 1>;
+                bits = <4 2>;
+            };
+            usb_rterm1: trim@55,4 {
+                reg = <0x55 1>;
+                bits = <4 2>;
+            };
+            usb_rterm2: trim@58,4 {
+                reg = <0x58 1>;
+                bits = <4 2>;
+            };
+            usb_rterm3: trim@59,4 {
+                reg = <0x59 1>;
+                bits = <4 2>;
+            };
+            usb_sel_t0: trim@54,0 {
+                reg = <0x54 1>;
+                bits = <0 4>;
+            };
+            usb_sel_t1: trim@55,0 {
+                reg = <0x55 1>;
+                bits = <0 4>;
+            };
+            usb_sel_t2: trim@58,0 {
+                reg = <0x58 1>;
+                bits = <0 4>;
+            };
+            usb_sel_t3: trim@59,0 {
+                reg = <0x59 1>;
+                bits = <0 4>;
+            };
+            usb_hs_i0: trim@56,0 {
+                reg = <0x56 1>;
+                bits = <0 4>;
+            };
+            usb_hs_i2: trim@5a,0 {
+                reg = <0x5a 1>;
+                bits = <0 4>;
+            };
+        };
+    };

Documentation/devicetree/bindings/nvmem/uniphier-efuse.txt

-= UniPhier eFuse device tree bindings =
-
-This UniPhier eFuse must be under soc-glue.
-
-Required properties:
-- compatible: should be "socionext,uniphier-efuse"
-- reg: should contain the register location and length
-
-= Data cells =
-Are child nodes of efuse, bindings of which as described in
-bindings/nvmem/nvmem.txt
-
-Example:
-
-	soc-glue@5f900000 {
-		compatible = "socionext,uniphier-ld20-soc-glue-debug",
-			     "simple-mfd";
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges = <0x0 0x5f900000 0x2000>;
-
-		efuse@100 {
-			compatible = "socionext,uniphier-efuse";
-			reg = <0x100 0x28>;
-		};
-
-		efuse@200 {
-			compatible = "socionext,uniphier-efuse";
-			reg = <0x200 0x68>;
-			#address-cells = <1>;
-			#size-cells = <1>;
-
-			/* Data cells */
-			usb_mon: usb-mon@54 {
-				reg = <0x54 0xc>;
-			};
-		};
-	};
-
-= Data consumers =
-Are device nodes which consume nvmem data cells.
-
-Example:
-
-	usb {
-		...
-		nvmem-cells = <&usb_mon>;
-		nvmem-cell-names = "usb_mon";
-	}

Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt

@@ -3,7 +3,7 @@ Amlogic Meson AXG DWC PCIE SoC controller
 Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
 It shares common functions with the PCIe DesignWare core driver and
 inherits common properties defined in
-Documentation/devicetree/bindings/pci/designware-pcie.txt.
+Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
 
 Additional properties are described here:
 
@@ -33,7 +33,7 @@ Required properties:
 - phy-names: must contain "pcie"
 
 - device_type:
-	should be "pci". As specified in designware-pcie.txt
+	should be "pci". As specified in snps,dw-pcie.yaml
 
 
 Example configuration:

Documentation/devicetree/bindings/pci/axis,artpec6-pcie.txt

 * Axis ARTPEC-6 PCIe interface
 
 This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
+and thus inherits all the common properties defined in snps,dw-pcie.yaml.
 
 Required properties:
 - compatible: "axis,artpec6-pcie", "snps,dw-pcie" for ARTPEC-6 in RC mode;

Documentation/devicetree/bindings/pci/designware-pcie.txt

-* Synopsys DesignWare PCIe interface
-
-Required properties:
-- compatible:
-	"snps,dw-pcie" for RC mode;
-	"snps,dw-pcie-ep" for EP mode;
-- reg: For designware cores version < 4.80 contains the configuration
-       address space. For designware core version >= 4.80, contains
-       the configuration and ATU address space
-- reg-names: Must be "config" for the PCIe configuration space and "atu" for
-	     the ATU address space.
-    (The old way of getting the configuration address space from "ranges"
-    is deprecated and should be avoided.)
-RC mode:
-- #address-cells: set to <3>
-- #size-cells: set to <2>
-- device_type: set to "pci"
-- ranges: ranges for the PCI memory and I/O regions
-- #interrupt-cells: set to <1>
-- interrupt-map-mask and interrupt-map: standard PCI
-	properties to define the mapping of the PCIe interface to interrupt
-	numbers.
-EP mode:
-- num-ib-windows: number of inbound address translation windows
-- num-ob-windows: number of outbound address translation windows
-
-Optional properties:
-- num-lanes: number of lanes to use (this property should be specified unless
-  the link is brought already up in BIOS)
-- reset-gpio: GPIO pin number of power good signal
-- clocks: Must contain an entry for each entry in clock-names.
-	See ../clocks/clock-bindings.txt for details.
-- clock-names: Must include the following entries:
-	- "pcie"
-	- "pcie_bus"
-- snps,enable-cdm-check: This is a boolean property and if present enables
-   automatic checking of CDM (Configuration Dependent Module) registers
-   for data corruption. CDM registers include standard PCIe configuration
-   space registers, Port Logic registers, DMA and iATU (internal Address
-   Translation Unit) registers.
-RC mode:
-- num-viewport: number of view ports configured in hardware. If a platform
-  does not specify it, the driver assumes 2.
-- bus-range: PCI bus numbers covered (it is recommended for new devicetrees
-  to specify this property, to keep backwards compatibility a range of
-  0x00-0xff is assumed if not present)
-
-EP mode:
-- max-functions: maximum number of functions that can be configured
-
-Example configuration:
-
-	pcie: pcie@dfc00000 {
-		compatible = "snps,dw-pcie";
-		reg = <0xdfc00000 0x0001000>, /* IP registers */
-		      <0xd0000000 0x0002000>; /* Configuration space */
-		reg-names = "dbi", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000
-			  0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>;
-		interrupts = <25>, <24>;
-		#interrupt-cells = <1>;
-		num-lanes = <1>;
-	};
-or
-	pcie: pcie@dfc00000 {
-		compatible = "snps,dw-pcie-ep";
-		reg = <0xdfc00000 0x0001000>, /* IP registers 1 */
-		      <0xdfc01000 0x0001000>, /* IP registers 2 */
-		      <0xd0000000 0x2000000>; /* Configuration space */
-		reg-names = "dbi", "dbi2", "addr_space";
-		num-ib-windows = <6>;
-		num-ob-windows = <2>;
-		num-lanes = <1>;
-	};

Documentation/devicetree/bindings/pci/faraday,ftpci100.txt

-Faraday Technology FTPCI100 PCI Host Bridge
-
-This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
-is a generic IP block from Faraday Technology. It exists in two variants:
-plain and dual PCI. The plain version embeds a cascading interrupt controller
-into the host bridge. The dual version routes the interrupts to the host
-chips interrupt controller.
-
-The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
-Technology) and product ID 0x4321.
-
-Mandatory properties:
-
-- compatible: ranging from specific to generic, should be one of
-  "cortina,gemini-pci", "faraday,ftpci100"
-  "cortina,gemini-pci-dual", "faraday,ftpci100-dual"
-  "faraday,ftpci100"
-  "faraday,ftpci100-dual"
-- reg: memory base and size for the host bridge
-- #address-cells: set to <3>
-- #size-cells: set to <2>
-- #interrupt-cells: set to <1>
-- bus-range: set to <0x00 0xff>
-- device_type, set to "pci"
-- ranges: see pci.txt
-- interrupt-map-mask: see pci.txt
-- interrupt-map: see pci.txt
-- dma-ranges: three ranges for the inbound memory region. The ranges must
-  be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
-  128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
-  pre-fetchable.
-
-Optional properties:
-- clocks: when present, this should contain the peripheral clock (PCLK) and the
-  PCI clock (PCICLK). If these are not present, they are assumed to be
-  hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
-- clock-names: when present, this should contain "PCLK" for the peripheral
-  clock and "PCICLK" for the PCI-side clock.
-
-Mandatory subnodes:
-- For "faraday,ftpci100" a node representing the interrupt-controller inside the
-  host bridge is mandatory. It has the following mandatory properties:
-  - interrupt: see interrupt-controller/interrupts.txt
-  - interrupt-controller: see interrupt-controller/interrupts.txt
-  - #address-cells: set to <0>
-  - #interrupt-cells: set to <1>
-
-I/O space considerations:
-
-The plain variant has 128MiB of non-prefetchable memory space, whereas the
-"dual" variant has 64MiB. Take this into account when describing the ranges.
-
-Interrupt map considerations:
-
-The "dual" variant will get INT A, B, C, D from the system interrupt controller
-and should point to respective interrupt in that controller in its
-interrupt-map.
-
-The code which is the only documentation of how the Faraday PCI (the non-dual
-variant) interrupts assigns the default interrupt mapping/swizzling has
-typically been like this, doing the swizzling on the interrupt controller side
-rather than in the interconnect:
-
-interrupt-map-mask = <0xf800 0 0 7>;
-interrupt-map =
-	<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-	<0x4800 0 0 2 &pci_intc 1>,
-	<0x4800 0 0 3 &pci_intc 2>,
-	<0x4800 0 0 4 &pci_intc 3>,
-	<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-	<0x5000 0 0 2 &pci_intc 2>,
-	<0x5000 0 0 3 &pci_intc 3>,
-	<0x5000 0 0 4 &pci_intc 0>,
-	<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-	<0x5800 0 0 2 &pci_intc 3>,
-	<0x5800 0 0 3 &pci_intc 0>,
-	<0x5800 0 0 4 &pci_intc 1>,
-	<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-	<0x6000 0 0 2 &pci_intc 0>,
-	<0x6000 0 0 3 &pci_intc 1>,
-	<0x6000 0 0 4 &pci_intc 2>;
-
-Example:
-
-pci@50000000 {
-	compatible = "cortina,gemini-pci", "faraday,ftpci100";
-	reg = <0x50000000 0x100>;
-	interrupts = <8 IRQ_TYPE_LEVEL_HIGH>, /* PCI A */
-			<26 IRQ_TYPE_LEVEL_HIGH>, /* PCI B */
-			<27 IRQ_TYPE_LEVEL_HIGH>, /* PCI C */
-			<28 IRQ_TYPE_LEVEL_HIGH>; /* PCI D */
-	#address-cells = <3>;
-	#size-cells = <2>;
-	#interrupt-cells = <1>;
-
-	bus-range = <0x00 0xff>;
-	ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
-		 <0x01000000 0 0          0x50000000 0 0x00100000>,
-		 /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
-		 <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
-
-	/* DMA ranges */
-	dma-ranges =
-	/* 128MiB at 0x00000000-0x07ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
-	/* 64MiB at 0x00000000-0x03ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
-	/* 64MiB at 0x00000000-0x03ffffff */
-	<0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
-
-	interrupt-map-mask = <0xf800 0 0 7>;
-	interrupt-map =
-		<0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
-		<0x4800 0 0 2 &pci_intc 1>,
-		<0x4800 0 0 3 &pci_intc 2>,
-		<0x4800 0 0 4 &pci_intc 3>,
-		<0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
-		<0x5000 0 0 2 &pci_intc 2>,
-		<0x5000 0 0 3 &pci_intc 3>,
-		<0x5000 0 0 4 &pci_intc 0>,
-		<0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
-		<0x5800 0 0 2 &pci_intc 3>,
-		<0x5800 0 0 3 &pci_intc 0>,
-		<0x5800 0 0 4 &pci_intc 1>,
-		<0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
-		<0x6000 0 0 2 &pci_intc 0>,
-		<0x6000 0 0 3 &pci_intc 0>,
-		<0x6000 0 0 4 &pci_intc 0>;
-	pci_intc: interrupt-controller {
-		interrupt-parent = <&intcon>;
-		interrupt-controller;
-		#address-cells = <0>;
-		#interrupt-cells = <1>;
-	};
-};

Documentation/devicetree/bindings/pci/faraday,ftpci100.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/faraday,ftpci100.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Faraday Technology FTPCI100 PCI Host Bridge
+
+maintainers:
+  - Linus Walleij <linus.walleij@linaro.org>
+
+description: |
+    This PCI bridge is found inside that Cortina Systems Gemini SoC platform and
+    is a generic IP block from Faraday Technology. It exists in two variants:
+    plain and dual PCI. The plain version embeds a cascading interrupt controller
+    into the host bridge. The dual version routes the interrupts to the host
+    chips interrupt controller.
+    The host controller appear on the PCI bus with vendor ID 0x159b (Faraday
+    Technology) and product ID 0x4321.
+    I/O space considerations:
+    The plain variant has 128MiB of non-prefetchable memory space, whereas the
+    "dual" variant has 64MiB. Take this into account when describing the ranges.
+
+    Interrupt map considerations:
+
+    The "dual" variant will get INT A, B, C, D from the system interrupt controller
+    and should point to respective interrupt in that controller in its interrupt-map.
+
+    The code which is the only documentation of how the Faraday PCI (the non-dual
+    variant) interrupts assigns the default interrupt mapping/swizzling has
+    typically been like this, doing the swizzling on the interrupt controller side
+    rather than in the interconnect:
+
+    interrupt-map-mask = <0xf800 0 0 7>;
+    interrupt-map =
+        <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+        <0x4800 0 0 2 &pci_intc 1>,
+        <0x4800 0 0 3 &pci_intc 2>,
+        <0x4800 0 0 4 &pci_intc 3>,
+        <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+        <0x5000 0 0 2 &pci_intc 2>,
+        <0x5000 0 0 3 &pci_intc 3>,
+        <0x5000 0 0 4 &pci_intc 0>,
+        <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+        <0x5800 0 0 2 &pci_intc 3>,
+        <0x5800 0 0 3 &pci_intc 0>,
+        <0x5800 0 0 4 &pci_intc 1>,
+        <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+        <0x6000 0 0 2 &pci_intc 0>,
+        <0x6000 0 0 3 &pci_intc 1>,
+        <0x6000 0 0 4 &pci_intc 2>;
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - const: cortina,gemini-pci
+          - const: faraday,ftpci100
+      - items:
+          - const: cortina,gemini-pci-dual
+          - const: faraday,ftpci100-dual
+      - const: faraday,ftpci100
+      - const: faraday,ftpci100-dual
+
+  reg:
+    maxItems: 1
+
+  "#address-cells":
+    const: 3
+
+  "#interrupt-cells":
+    const: 1
+
+  ranges:
+    minItems: 2
+
+  dma-ranges:
+    minItems: 3
+    description: |
+      three ranges for the inbound memory region. The ranges must
+      be aligned to a 1MB boundary, and may be 1MB, 2MB, 4MB, 8MB, 16MB, 32MB, 64MB,
+      128MB, 256MB, 512MB, 1GB or 2GB in size. The memory should be marked as
+      pre-fetchable.
+
+  clocks:
+    items:
+      - description: peripheral clock (PCLK)
+      - description: PCI clock (PCICLK).
+    description: |
+      If these are not present, they are assumed to be
+      hard-wired enabled and always on. The PCI clock will be 33 or 66 MHz.
+
+  clock-names:
+    items:
+      - const: PCLK
+      - const: PCICLK
+
+  interrupt-controller:
+    type: object
+
+required:
+  - reg
+  - compatible
+  - "#interrupt-cells"
+  - interrupt-map-mask
+  - interrupt-map
+  - dma-ranges
+
+if:
+  properties:
+    compatible:
+      contains:
+        const: faraday,ftpci100
+then:
+  required:
+    - interrupt-controller
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    pci@50000000 {
+      compatible = "cortina,gemini-pci", "faraday,ftpci100";
+      reg = <0x50000000 0x100>;
+      device_type = "pci";
+      #address-cells = <3>;
+      #size-cells = <2>;
+      #interrupt-cells = <1>;
+
+      bus-range = <0x00 0xff>;
+      ranges = /* 1MiB I/O space 0x50000000-0x500fffff */
+        <0x01000000 0 0          0x50000000 0 0x00100000>,
+        /* 128MiB non-prefetchable memory 0x58000000-0x5fffffff */
+        <0x02000000 0 0x58000000 0x58000000 0 0x08000000>;
+
+      /* DMA ranges */
+      dma-ranges =
+        /* 128MiB at 0x00000000-0x07ffffff */
+        <0x02000000 0 0x00000000 0x00000000 0 0x08000000>,
+        /* 64MiB at 0x00000000-0x03ffffff */
+        <0x02000000 0 0x00000000 0x00000000 0 0x04000000>,
+        /* 64MiB at 0x00000000-0x03ffffff */
+        <0x02000000 0 0x00000000 0x00000000 0 0x04000000>;
+
+      interrupt-map-mask = <0xf800 0 0 7>;
+      interrupt-map =
+        <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
+        <0x4800 0 0 2 &pci_intc 1>,
+        <0x4800 0 0 3 &pci_intc 2>,
+        <0x4800 0 0 4 &pci_intc 3>,
+        <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
+        <0x5000 0 0 2 &pci_intc 2>,
+        <0x5000 0 0 3 &pci_intc 3>,
+        <0x5000 0 0 4 &pci_intc 0>,
+        <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
+        <0x5800 0 0 2 &pci_intc 3>,
+        <0x5800 0 0 3 &pci_intc 0>,
+        <0x5800 0 0 4 &pci_intc 1>,
+        <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
+        <0x6000 0 0 2 &pci_intc 0>,
+        <0x6000 0 0 3 &pci_intc 0>,
+        <0x6000 0 0 4 &pci_intc 0>;
+      pci_intc: interrupt-controller {
+        interrupt-parent = <&intcon>;
+        interrupt-controller;
+        interrupts = <8 IRQ_TYPE_LEVEL_HIGH>;
+        #address-cells = <0>;
+        #interrupt-cells = <1>;
+      };
+    };

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt

-* Freescale i.MX6 PCIe interface
-
-This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
-
-Required properties:
-- compatible:
-	- "fsl,imx6q-pcie"
-	- "fsl,imx6sx-pcie",
-	- "fsl,imx6qp-pcie"
-	- "fsl,imx7d-pcie"
-	- "fsl,imx8mq-pcie"
-- reg: base address and length of the PCIe controller
-- interrupts: A list of interrupt outputs of the controller. Must contain an
-  entry for each entry in the interrupt-names property.
-- interrupt-names: Must include the following entries:
-	- "msi": The interrupt that is asserted when an MSI is received
-- clock-names: Must include the following additional entries:
-	- "pcie_phy"
-
-Optional properties:
-- fsl,tx-deemph-gen1: Gen1 De-emphasis value. Default: 0
-- fsl,tx-deemph-gen2-3p5db: Gen2 (3.5db) De-emphasis value. Default: 0
-- fsl,tx-deemph-gen2-6db: Gen2 (6db) De-emphasis value. Default: 20
-- fsl,tx-swing-full: Gen2 TX SWING FULL value. Default: 127
-- fsl,tx-swing-low: TX launch amplitude swing_low value. Default: 127
-- fsl,max-link-speed: Specify PCI gen for link capability. Must be '2' for
-  gen2, otherwise will default to gen1. Note that the IMX6 LVDS clock outputs
-  do not meet gen2 jitter requirements and thus for gen2 capability a gen2
-  compliant clock generator should be used and configured.
-- reset-gpio: Should specify the GPIO for controlling the PCI bus device reset
-  signal. It's not polarity aware and defaults to active-low reset sequence
-  (L=reset state, H=operation state).
-- reset-gpio-active-high: If present then the reset sequence using the GPIO
-  specified in the "reset-gpio" property is reversed (H=reset state,
-  L=operation state).
-- vpcie-supply: Should specify the regulator in charge of PCIe port power.
-  The regulator will be enabled when initializing the PCIe host and
-  disabled either as part of the init process or when shutting down the
-  host.
-- vph-supply: Should specify the regulator in charge of VPH one of the three
-  PCIe PHY powers. This regulator can be supplied by both 1.8v and 3.3v voltage
-  supplies.
-
-Additional required properties for imx6sx-pcie:
-- clock names: Must include the following additional entries:
-	- "pcie_inbound_axi"
-- power-domains: Must be set to phandles pointing to the DISPLAY and
-  PCIE_PHY power domains
-- power-domain-names: Must be "pcie", "pcie_phy"
-
-Additional required properties for imx7d-pcie and imx8mq-pcie:
-- power-domains: Must be set to a phandle pointing to PCIE_PHY power domain
-- resets: Must contain phandles to PCIe-related reset lines exposed by SRC
-  IP block
-- reset-names: Must contain the following entries:
-	       - "pciephy"
-	       - "apps"
-	       - "turnoff"
-- fsl,imx7d-pcie-phy: A phandle to an fsl,imx7d-pcie-phy node.
-
-Additional required properties for imx8mq-pcie:
-- clock-names: Must include the following additional entries:
-	- "pcie_aux"
-
-Example:
-
-	pcie@01000000 {
-		compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
-		reg = <0x01ffc000 0x04000>,
-		      <0x01f00000 0x80000>;
-		reg-names = "dbi", "config";
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
-			  0x81000000 0 0          0x01f80000 0 0x00010000
-			  0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
-		num-lanes = <1>;
-		interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "msi";
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0 0 0 0x7>;
-		interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
-		                <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&clks 144>, <&clks 206>, <&clks 189>;
-		clock-names = "pcie", "pcie_bus", "pcie_phy";
-	};
-
-* Freescale i.MX7d PCIe PHY
-
-This is the PHY associated with the IMX7d PCIe controller.  It's used by the
-PCI-e controller via the fsl,imx7d-pcie-phy phandle.
-
-Required properties:
-- compatible:
-	- "fsl,imx7d-pcie-phy"
-- reg: base address and length of the PCIe PHY controller

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/fsl,imx6q-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale i.MX6 PCIe host controller
+
+maintainers:
+  - Lucas Stach <l.stach@pengutronix.de>
+  - Richard Zhu <hongxing.zhu@nxp.com>
+
+description: |+
+  This PCIe host controller is based on the Synopsys DesignWare PCIe IP
+  and thus inherits all the common properties defined in snps,dw-pcie.yaml.
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+properties:
+  compatible:
+    enum:
+      - fsl,imx6q-pcie
+      - fsl,imx6sx-pcie
+      - fsl,imx6qp-pcie
+      - fsl,imx7d-pcie
+      - fsl,imx8mq-pcie
+
+  reg:
+    items:
+      - description: Data Bus Interface (DBI) registers.
+      - description: PCIe configuration space region.
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: config
+
+  interrupts:
+    items:
+      - description: builtin MSI controller.
+
+  interrupt-names:
+    minItems: 1
+    items:
+      - const: msi
+
+  clocks:
+    minItems: 3
+    items:
+      - description: PCIe bridge clock.
+      - description: PCIe bus clock.
+      - description: PCIe PHY clock.
+      - description: Additional required clock entry for imx6sx-pcie,
+          imx8mq-pcie.
+
+  clock-names:
+    minItems: 3
+    items:
+      - const: pcie
+      - const: pcie_bus
+      - const: pcie_phy
+      - const: pcie_inbound_axi for imx6sx-pcie, pcie_aux for imx8mq-pcie
+
+  num-lanes:
+    const: 1
+
+  fsl,imx7d-pcie-phy:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: A phandle to an fsl,imx7d-pcie-phy node. Additional
+      required properties for imx7d-pcie and imx8mq-pcie.
+
+  power-domains:
+    items:
+      - description: The phandle pointing to the DISPLAY domain for
+          imx6sx-pcie, to PCIE_PHY power domain for imx7d-pcie and
+          imx8mq-pcie.
+      - description: The phandle pointing to the PCIE_PHY power domains
+          for imx6sx-pcie.
+
+  power-domain-names:
+    items:
+      - const: pcie
+      - const: pcie_phy
+
+  resets:
+    maxItems: 3
+    description: Phandles to PCIe-related reset lines exposed by SRC
+      IP block. Additional required by imx7d-pcie and imx8mq-pcie.
+
+  reset-names:
+    items:
+      - const: pciephy
+      - const: apps
+      - const: turnoff
+
+  fsl,tx-deemph-gen1:
+    description: Gen1 De-emphasis value (optional required).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  fsl,tx-deemph-gen2-3p5db:
+    description: Gen2 (3.5db) De-emphasis value (optional required).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 0
+
+  fsl,tx-deemph-gen2-6db:
+    description: Gen2 (6db) De-emphasis value (optional required).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 20
+
+  fsl,tx-swing-full:
+    description: Gen2 TX SWING FULL value (optional required).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 127
+
+  fsl,tx-swing-low:
+    description: TX launch amplitude swing_low value (optional required).
+    $ref: /schemas/types.yaml#/definitions/uint32
+    default: 127
+
+  fsl,max-link-speed:
+    description: Specify PCI Gen for link capability (optional required).
+      Note that the IMX6 LVDS clock outputs do not meet gen2 jitter
+      requirements and thus for gen2 capability a gen2 compliant clock
+      generator should be used and configured.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    enum: [1, 2, 3, 4]
+    default: 1
+
+  reset-gpio:
+    description: Should specify the GPIO for controlling the PCI bus device
+      reset signal. It's not polarity aware and defaults to active-low reset
+      sequence (L=reset state, H=operation state) (optional required).
+
+  reset-gpio-active-high:
+    description: If present then the reset sequence using the GPIO
+      specified in the "reset-gpio" property is reversed (H=reset state,
+      L=operation state) (optional required).
+
+  vpcie-supply:
+    description: Should specify the regulator in charge of PCIe port power.
+      The regulator will be enabled when initializing the PCIe host and
+      disabled either as part of the init process or when shutting down
+      the host (optional required).
+
+  vph-supply:
+    description: Should specify the regulator in charge of VPH one of
+      the three PCIe PHY powers. This regulator can be supplied by both
+      1.8v and 3.3v voltage supplies (optional required).
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - "#address-cells"
+  - "#size-cells"
+  - device_type
+  - bus-range
+  - ranges
+  - num-lanes
+  - interrupts
+  - interrupt-names
+  - "#interrupt-cells"
+  - interrupt-map-mask
+  - interrupt-map
+  - clocks
+  - clock-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/imx6qdl-clock.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    pcie: pcie@1ffc000 {
+        compatible = "fsl,imx6q-pcie";
+        reg = <0x01ffc000 0x04000>,
+              <0x01f00000 0x80000>;
+        reg-names = "dbi", "config";
+        #address-cells = <3>;
+        #size-cells = <2>;
+        device_type = "pci";
+        bus-range = <0x00 0xff>;
+        ranges = <0x81000000 0 0          0x01f80000 0 0x00010000>,
+                 <0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
+        num-lanes = <1>;
+        interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "msi";
+        #interrupt-cells = <1>;
+        interrupt-map-mask = <0 0 0 0x7>;
+        interrupt-map = <0 0 0 1 &gpc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 2 &gpc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 3 &gpc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
+                        <0 0 0 4 &gpc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&clks IMX6QDL_CLK_PCIE_AXI>,
+                <&clks IMX6QDL_CLK_LVDS1_GATE>,
+                <&clks IMX6QDL_CLK_PCIE_REF_125M>;
+        clock-names = "pcie", "pcie_bus", "pcie_phy";
+    };
+...

Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/hisilicon,kirin-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin SoCs PCIe host DT description
+
+maintainers:
+  - Xiaowei Song <songxiaowei@hisilicon.com>
+  - Binghui Wang <wangbinghui@hisilicon.com>
+
+description: |
+  Kirin PCIe host controller is based on the Synopsys DesignWare PCI core.
+  It shares common functions with the PCIe DesignWare core driver and
+  inherits common properties defined in
+  Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+properties:
+  compatible:
+    contains:
+      enum:
+        - hisilicon,kirin960-pcie
+        - hisilicon,kirin970-pcie
+
+  reg:
+    description: |
+      Should contain dbi, apb, config registers location and length.
+      For hisilicon,kirin960-pcie, it should also contain phy.
+    minItems: 3
+    maxItems: 4
+
+  reg-names:
+    minItems: 3
+    maxItems: 4
+
+  hisilicon,clken-gpios:
+    description: |
+      Clock input enablement GPIOs from PCI devices like Ethernet, M.2 and
+      mini-PCIe slots.
+
+required:
+  - compatible
+  - reg
+  - reg-names
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/clock/hi3660-clock.h>
+    #include <dt-bindings/clock/hi3670-clock.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+
+      pcie@f4000000 {
+        compatible = "hisilicon,kirin960-pcie";
+        reg = <0x0 0xf4000000 0x0 0x1000>,
+              <0x0 0xff3fe000 0x0 0x1000>,
+              <0x0 0xf3f20000 0x0 0x40000>,
+              <0x0 0xf5000000 0x0 0x2000>;
+        reg-names = "dbi", "apb", "phy", "config";
+        bus-range = <0x0  0xff>;
+        #address-cells = <3>;
+        #size-cells = <2>;
+        device_type = "pci";
+        ranges = <0x02000000 0x0 0x00000000
+                  0x0 0xf6000000
+                  0x0 0x02000000>;
+        num-lanes = <1>;
+        #interrupt-cells = <1>;
+        interrupts = <0 283 4>;
+        interrupt-names = "msi";
+        interrupt-map-mask = <0xf800 0 0 7>;
+        interrupt-map = <0x0 0 0 1 &gic GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 2 &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 3 &gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 4 &gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+        clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
+                 <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
+                 <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
+                 <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
+                 <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
+        clock-names = "pcie_phy_ref", "pcie_aux", "pcie_apb_phy",
+                      "pcie_apb_sys", "pcie_aclk";
+      };
+
+      pcie@f5000000 {
+        compatible = "hisilicon,kirin970-pcie";
+        reg = <0x0 0xf4000000 0x0 0x1000000>,
+              <0x0 0xfc180000 0x0 0x1000>,
+              <0x0 0xf5000000 0x0 0x2000>;
+        reg-names = "dbi", "apb", "config";
+        bus-range = <0x0  0xff>;
+        #address-cells = <3>;
+        #size-cells = <2>;
+        device_type = "pci";
+        phys = <&pcie_phy>;
+        ranges = <0x02000000 0x0 0x00000000
+                  0x0 0xf6000000
+                  0x0 0x02000000>;
+        num-lanes = <1>;
+        #interrupt-cells = <1>;
+        interrupts = <GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>;
+        interrupt-names = "msi";
+        interrupt-map-mask = <0 0 0 7>;
+        interrupt-map = <0x0 0 0 1 &gic GIC_SPI 282 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 2 &gic GIC_SPI 283 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 3 &gic GIC_SPI 284 IRQ_TYPE_LEVEL_HIGH>,
+                        <0x0 0 0 4 &gic GIC_SPI 285 IRQ_TYPE_LEVEL_HIGH>;
+        reset-gpios = <&gpio7 0 0>;
+        hisilicon,clken-gpios = <&gpio27 3 0>, <&gpio17 0 0>, <&gpio20 6 0>;
+        pcie@0,0 { // Lane 0: PCIe switch: Bus 1, Device 0
+          reg = <0 0 0 0 0>;
+          compatible = "pciclass,0604";
+          device_type = "pci";
+          #address-cells = <3>;
+          #size-cells = <2>;
+          ranges;
+
+          pcie@0,0 { // Lane 0: upstream
+            reg = <0 0 0 0 0>;
+            compatible = "pciclass,0604";
+            device_type = "pci";
+            #address-cells = <3>;
+            #size-cells = <2>;
+            ranges;
+
+            pcie@1,0 { // Lane 4: M.2
+              reg = <0x0800 0 0 0 0>;
+              compatible = "pciclass,0604";
+              device_type = "pci";
+              reset-gpios = <&gpio3 1 0>;
+              #address-cells = <3>;
+              #size-cells = <2>;
+              ranges;
+            };
+
+            pcie@5,0 { // Lane 5: Mini PCIe
+              reg = <0x2800 0 0 0 0>;
+              compatible = "pciclass,0604";
+              device_type = "pci";
+              reset-gpios = <&gpio27 4 0 >;
+              #address-cells = <3>;
+              #size-cells = <2>;
+              ranges;
+            };
+
+            pcie@7,0 { // Lane 6: Ethernet
+              reg = <0x03800 0 0 0 0>;
+              compatible = "pciclass,0604";
+              device_type = "pci";
+              reset-gpios = <&gpio25 2 0 >;
+              #address-cells = <3>;
+              #size-cells = <2>;
+              ranges;
+            };
+          };
+        };
+      };
+    };

Documentation/devicetree/bindings/pci/hisilicon-histb-pcie.txt

@@ -3,7 +3,7 @@ HiSilicon STB PCIe host bridge DT description
 The HiSilicon STB PCIe host controller is based on the DesignWare PCIe core.
 It shares common functions with the DesignWare PCIe core driver and inherits
 common properties defined in
-Documentation/devicetree/bindings/pci/designware-pcie.txt.
+Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
 
 Additional properties are described here:
 

Documentation/devicetree/bindings/pci/intel-gw-pcie.yaml

@@ -7,7 +7,7 @@ $schema: http://devicetree.org/meta-schemas/core.yaml#
 title: PCIe RC controller on Intel Gateway SoCs
 
 maintainers:
-  - Dilip Kota <eswara.kota@linux.intel.com>
+  - Rahul Tanwar <rtanwar@maxlinear.com>
 
 select:
   properties:
@@ -17,21 +17,15 @@ select:
   required:
     - compatible
 
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
 properties:
   compatible:
     items:
       - const: intel,lgm-pcie
       - const: snps,dw-pcie
 
-  device_type:
-    const: pci
-
-  "#address-cells":
-    const: 3
-
-  "#size-cells":
-    const: 2
-
   reg:
     items:
       - description: Controller control and status registers.
@@ -62,30 +56,13 @@ properties:
   reset-gpios:
     maxItems: 1
 
-  linux,pci-domain: true
-
   num-lanes:
     maximum: 2
-    description: Number of lanes to use for this port.
-
-  '#interrupt-cells':
-    const: 1
-
-  interrupt-map-mask:
-    description: Standard PCI IRQ mapping properties.
-
-  interrupt-map:
-    description: Standard PCI IRQ mapping properties.
 
   max-link-speed:
-    description: Specify PCI Gen for link capability.
-    $ref: /schemas/types.yaml#/definitions/uint32
     enum: [1, 2, 3, 4]
     default: 1
 
-  bus-range:
-    description: Range of bus numbers associated with this controller.
-
   reset-assert-ms:
     description: |
       Delay after asserting reset to the PCIe device.
@@ -94,9 +71,6 @@ properties:
 
 required:
   - compatible
-  - device_type
-  - "#address-cells"
-  - "#size-cells"
   - reg
   - reg-names
   - ranges
@@ -109,7 +83,7 @@ required:
   - interrupt-map
   - interrupt-map-mask
 
-additionalProperties: false
+unevaluatedProperties: false
 
 examples:
   - |

Documentation/devicetree/bindings/pci/kirin-pcie.txt

-HiSilicon Kirin SoCs PCIe host DT description
-
-Kirin PCIe host controller is based on the Synopsys DesignWare PCI core.
-It shares common functions with the PCIe DesignWare core driver and
-inherits common properties defined in
-Documentation/devicetree/bindings/pci/designware-pcie.txt.
-
-Additional properties are described here:
-
-Required properties
-- compatible:
-	"hisilicon,kirin960-pcie" for PCIe of Kirin960 SoC
-- reg: Should contain rc_dbi, apb, phy, config registers location and length.
-- reg-names: Must include the following entries:
-  "dbi": controller configuration registers;
-  "apb": apb Ctrl register defined by Kirin;
-  "phy": apb PHY register defined by Kirin;
-  "config": PCIe configuration space registers.
-- reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
-
-Optional properties:
-
-Example based on kirin960:
-
-	pcie@f4000000 {
-		compatible = "hisilicon,kirin-pcie";
-		reg = <0x0 0xf4000000 0x0 0x1000>, <0x0 0xff3fe000 0x0 0x1000>,
-		      <0x0 0xf3f20000 0x0 0x40000>, <0x0 0xF4000000 0 0x2000>;
-		reg-names = "dbi","apb","phy", "config";
-		bus-range = <0x0  0x1>;
-		#address-cells = <3>;
-		#size-cells = <2>;
-		device_type = "pci";
-		ranges = <0x02000000 0x0 0x00000000 0x0 0xf5000000 0x0 0x2000000>;
-		num-lanes = <1>;
-		#interrupt-cells = <1>;
-		interrupt-map-mask = <0xf800 0 0 7>;
-		interrupt-map = <0x0 0 0 1 &gic 0 0 0  282 4>,
-				<0x0 0 0 2 &gic 0 0 0  283 4>,
-				<0x0 0 0 3 &gic 0 0 0  284 4>,
-				<0x0 0 0 4 &gic 0 0 0  285 4>;
-		clocks = <&crg_ctrl HI3660_PCIEPHY_REF>,
-			 <&crg_ctrl HI3660_CLK_GATE_PCIEAUX>,
-			 <&crg_ctrl HI3660_PCLK_GATE_PCIE_PHY>,
-			 <&crg_ctrl HI3660_PCLK_GATE_PCIE_SYS>,
-			 <&crg_ctrl HI3660_ACLK_GATE_PCIE>;
-		clock-names = "pcie_phy_ref", "pcie_aux",
-			      "pcie_apb_phy", "pcie_apb_sys", "pcie_aclk";
-		reset-gpios = <&gpio11 1 0 >;
-	};

Documentation/devicetree/bindings/pci/layerscape-pci.txt

 Freescale Layerscape PCIe controller
 
 This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
+and thus inherits all the common properties defined in snps,dw-pcie.yaml.
 
 This controller derives its clocks from the Reset Configuration Word (RCW)
 which is used to describe the PLL settings at the time of chip-reset.

Documentation/devicetree/bindings/pci/loongson.yaml

@@ -17,10 +17,10 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: loongson,ls2k-pci
-      - const: loongson,ls7a-pci
-      - const: loongson,rs780e-pci
+    enum:
+      - loongson,ls2k-pci
+      - loongson,ls7a-pci
+      - loongson,rs780e-pci
 
   reg:
     minItems: 1

Documentation/devicetree/bindings/pci/nvidia,tegra194-pcie.txt

 NVIDIA Tegra PCIe controller (Synopsys DesignWare Core based)
 
 This PCIe controller is based on the Synopsis Designware PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
+and thus inherits all the common properties defined in snps,dw-pcie.yaml and
+snps,dw-pcie-ep.yaml.
 Some of the controller instances are dual mode where in they can work either
 in root port mode or endpoint mode but one at a time.
 
@@ -22,7 +23,7 @@ Required properties:
   property.
 - reg-names: Must include the following entries:
   "appl": Controller's application logic registers
-  "config": As per the definition in designware-pcie.txt
+  "config": As per the definition in snps,dw-pcie.yaml
   "atu_dma": iATU and DMA registers. This is where the iATU (internal Address
              Translation Unit) registers of the PCIe core are made available
              for SW access.

Documentation/devicetree/bindings/pci/pci-armada8k.txt

 * Marvell Armada 7K/8K PCIe interface
 
 This PCIe host controller is based on the Synopsys DesignWare PCIe IP
-and thus inherits all the common properties defined in designware-pcie.txt.
+and thus inherits all the common properties defined in snps,dw-pcie.yaml.
 
 Required properties:
 - compatible: "marvell,armada8k-pcie"

Documentation/devicetree/bindings/pci/pcie-al.txt

@@ -2,7 +2,7 @@
 
 Amazon's Annapurna Labs PCIe Host Controller is based on the Synopsys DesignWare
 PCI core. It inherits common properties defined in
-Documentation/devicetree/bindings/pci/designware-pcie.txt.
+Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
 
 Properties of the host controller node that differ from it are:
 

Documentation/devicetree/bindings/pci/qcom,pcie.txt

@@ -34,22 +34,22 @@
 - device_type:
 	Usage: required
 	Value type: <string>
-	Definition: Should be "pci". As specified in designware-pcie.txt
+	Definition: Should be "pci". As specified in snps,dw-pcie.yaml
 
 - #address-cells:
 	Usage: required
 	Value type: <u32>
-	Definition: Should be 3. As specified in designware-pcie.txt
+	Definition: Should be 3. As specified in snps,dw-pcie.yaml
 
 - #size-cells:
 	Usage: required
 	Value type: <u32>
-	Definition: Should be 2. As specified in designware-pcie.txt
+	Definition: Should be 2. As specified in snps,dw-pcie.yaml
 
 - ranges:
 	Usage: required
 	Value type: <prop-encoded-array>
-	Definition: As specified in designware-pcie.txt
+	Definition: As specified in snps,dw-pcie.yaml
 
 - interrupts:
 	Usage: required
@@ -64,17 +64,17 @@
 - #interrupt-cells:
 	Usage: required
 	Value type: <u32>
-	Definition: Should be 1. As specified in designware-pcie.txt
+	Definition: Should be 1. As specified in snps,dw-pcie.yaml
 
 - interrupt-map-mask:
 	Usage: required
 	Value type: <prop-encoded-array>
-	Definition: As specified in designware-pcie.txt
+	Definition: As specified in snps,dw-pcie.yaml
 
 - interrupt-map:
 	Usage: required
 	Value type: <prop-encoded-array>
-	Definition: As specified in designware-pcie.txt
+	Definition: As specified in snps,dw-pcie.yaml
 
 - clocks:
 	Usage: required

Documentation/devicetree/bindings/pci/samsung,exynos-pcie.yaml

@@ -13,10 +13,10 @@ maintainers:
 description: |+
   Exynos5433 SoC PCIe host controller is based on the Synopsys DesignWare
   PCIe IP and thus inherits all the common properties defined in
-  designware-pcie.txt.
+  snps,dw-pcie.yaml.
 
 allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
 
 properties:
   compatible:

Documentation/devicetree/bindings/pci/sifive,fu740-pcie.yaml

@@ -10,14 +10,14 @@ description: |+
   SiFive FU740 PCIe host controller is based on the Synopsys DesignWare
   PCI core. It shares common features with the PCIe DesignWare core and
   inherits common properties defined in
-  Documentation/devicetree/bindings/pci/designware-pcie.txt.
+  Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
 
 maintainers:
   - Paul Walmsley <paul.walmsley@sifive.com>
   - Greentime Hu <greentime.hu@sifive.com>
 
 allOf:
-  - $ref: /schemas/pci/pci-bus.yaml#
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
 
 properties:
   compatible:

Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/snps,dw-pcie-ep.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare PCIe endpoint interface
+
+maintainers:
+  - Jingoo Han <jingoohan1@gmail.com>
+  - Gustavo Pimentel <gustavo.pimentel@synopsys.com>
+
+description: |
+  Synopsys DesignWare PCIe host controller endpoint
+
+allOf:
+  - $ref: /schemas/pci/pci-ep.yaml#
+
+properties:
+  compatible:
+    anyOf:
+      - {}
+      - const: snps,dw-pcie-ep
+
+  reg:
+    description: |
+      It should contain Data Bus Interface (dbi) and config registers for all
+      versions.
+      For designware core version >= 4.80, it may contain ATU address space.
+    minItems: 2
+    maxItems: 4
+
+  reg-names:
+    minItems: 2
+    maxItems: 4
+    items:
+      enum: [dbi, dbi2, config, atu, addr_space, link, atu_dma, appl]
+
+  reset-gpio:
+    description: GPIO pin number of PERST# signal
+    maxItems: 1
+    deprecated: true
+
+  reset-gpios:
+    description: GPIO controlled connection to PERST# signal
+    maxItems: 1
+
+  snps,enable-cdm-check:
+    type: boolean
+    description: |
+      This is a boolean property and if present enables
+      automatic checking of CDM (Configuration Dependent Module) registers
+      for data corruption. CDM registers include standard PCIe configuration
+      space registers, Port Logic registers, DMA and iATU (internal Address
+      Translation Unit) registers.
+
+  num-ib-windows:
+    description: number of inbound address translation windows
+    maxItems: 1
+    deprecated: true
+
+  num-ob-windows:
+    description: number of outbound address translation windows
+    maxItems: 1
+    deprecated: true
+
+  max-functions:
+    $ref: /schemas/types.yaml#/definitions/uint32
+    description: maximum number of functions that can be configured
+
+required:
+  - reg
+  - reg-names
+  - compatible
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    bus {
+      #address-cells = <1>;
+      #size-cells = <1>;
+      pcie-ep@dfd00000 {
+        compatible = "snps,dw-pcie-ep";
+        reg = <0xdfc00000 0x0001000>, /* IP registers 1 */
+              <0xdfc01000 0x0001000>, /* IP registers 2 */
+              <0xd0000000 0x2000000>; /* Configuration space */
+        reg-names = "dbi", "dbi2", "addr_space";
+      };
+    };

Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/snps,dw-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys DesignWare PCIe interface
+
+maintainers:
+  - Jingoo Han <jingoohan1@gmail.com>
+  - Gustavo Pimentel <gustavo.pimentel@synopsys.com>
+
+description: |
+  Synopsys DesignWare PCIe host controller
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+  compatible:
+    anyOf:
+      - {}
+      - const: snps,dw-pcie
+
+  reg:
+    description: |
+      It should contain Data Bus Interface (dbi) and config registers for all
+      versions.
+      For designware core version >= 4.80, it may contain ATU address space.
+    minItems: 2
+    maxItems: 5
+
+  reg-names:
+    minItems: 2
+    maxItems: 5
+    items:
+      enum: [ dbi, dbi2, config, atu, app, elbi, mgmt, ctrl, parf, cfg, link,
+              ulreg, smu, mpu, apb, phy ]
+
+  num-lanes:
+    description: |
+      number of lanes to use (this property should be specified unless
+      the link is brought already up in firmware)
+    maximum: 16
+
+  reset-gpio:
+    description: GPIO pin number of PERST# signal
+    maxItems: 1
+    deprecated: true
+
+  reset-gpios:
+    description: GPIO controlled connection to PERST# signal
+    maxItems: 1
+
+  interrupts: true
+
+  interrupt-names: true
+
+  clocks: true
+
+  snps,enable-cdm-check:
+    type: boolean
+    description: |
+      This is a boolean property and if present enables
+      automatic checking of CDM (Configuration Dependent Module) registers
+      for data corruption. CDM registers include standard PCIe configuration
+      space registers, Port Logic registers, DMA and iATU (internal Address
+      Translation Unit) registers.
+
+  num-viewport:
+    description: |
+      number of view ports configured in hardware. If a platform
+      does not specify it, the driver autodetects it.
+    deprecated: true
+
+unevaluatedProperties: false
+
+required:
+  - reg
+  - reg-names
+  - compatible
+
+examples:
+  - |
+    bus {
+      #address-cells = <1>;
+      #size-cells = <1>;
+      pcie@dfc00000 {
+        device_type = "pci";
+        compatible = "snps,dw-pcie";
+        reg = <0xdfc00000 0x0001000>, /* IP registers */
+              <0xd0000000 0x0002000>; /* Configuration space */
+        reg-names = "dbi", "config";
+        #address-cells = <3>;
+        #size-cells = <2>;
+        ranges = <0x81000000 0 0x00000000 0xde000000 0 0x00010000>,
+                 <0x82000000 0 0xd0400000 0xd0400000 0 0x0d000000>;
+        interrupts = <25>, <24>;
+        #interrupt-cells = <1>;
+        num-lanes = <1>;
+      };
+    };

Documentation/devicetree/bindings/pci/socionext,uniphier-pcie-ep.yaml

@@ -10,13 +10,13 @@ description: |
   UniPhier PCIe endpoint controller is based on the Synopsys DesignWare
   PCI core. It shares common features with the PCIe DesignWare core and
   inherits common properties defined in
-  Documentation/devicetree/bindings/pci/designware-pcie.txt.
+  Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml.
 
 maintainers:
   - Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
 
 allOf:
-  - $ref: "pci-ep.yaml#"
+  - $ref: /schemas/pci/snps,dw-pcie-ep.yaml#
 
 properties:
   compatible:

Documentation/devicetree/bindings/pci/ti-pci.txt

@@ -12,7 +12,7 @@ PCIe DesignWare Controller
 	       number of PHYs as specified in *phys* property.
  - ti,hwmods : Name of the hwmod associated to the pcie, "pcie<X>",
 	       where <X> is the instance number of the pcie from the HW spec.
- - num-lanes as specified in ../designware-pcie.txt
+ - num-lanes as specified in ../snps,dw-pcie.yaml
  - ti,syscon-lane-sel : phandle/offset pair. Phandle to the system control
 			module and the register offset to specify lane
 			selection.
@@ -32,7 +32,7 @@ HOST MODE
    device_type,
    ranges,
    interrupt-map-mask,
-   interrupt-map : as specified in ../designware-pcie.txt
+   interrupt-map : as specified in ../snps,dw-pcie.yaml
  - ti,syscon-unaligned-access: phandle to the syscon DT node. The 1st argument
 			       should contain the register offset within syscon
 			       and the 2nd argument should contain the bit field

Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/toshiba,visconti-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba Visconti5 SoC PCIe Host Controller Device Tree Bindings
+
+maintainers:
+  - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+
+description:
+  Toshiba Visconti5 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP.
+
+allOf:
+  - $ref: /schemas/pci/snps,dw-pcie.yaml#
+
+properties:
+  compatible:
+    const: toshiba,visconti-pcie
+
+  reg:
+    items:
+      - description: Data Bus Interface (DBI) registers.
+      - description: PCIe configuration space region.
+      - description: Visconti specific additional registers.
+      - description: Visconti specific SMU registers
+      - description: Visconti specific memory protection unit registers (MPU)
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: config
+      - const: ulreg
+      - const: smu
+      - const: mpu
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: PCIe reference clock
+      - description: PCIe system clock
+      - description: Auxiliary clock
+
+  clock-names:
+    items:
+      - const: ref
+      - const: core
+      - const: aux
+
+  num-lanes:
+    const: 2
+
+required:
+  - reg
+  - reg-names
+  - interrupts
+  - "#interrupt-cells"
+  - interrupt-map
+  - interrupt-map-mask
+  - num-lanes
+  - clocks
+  - clock-names
+  - max-link-speed
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie: pcie@28400000 {
+            compatible = "toshiba,visconti-pcie";
+            reg = <0x0 0x28400000 0x0 0x00400000>,
+                  <0x0 0x70000000 0x0 0x10000000>,
+                  <0x0 0x28050000 0x0 0x00010000>,
+                  <0x0 0x24200000 0x0 0x00002000>,
+                  <0x0 0x24162000 0x0 0x00001000>;
+            reg-names  = "dbi", "config", "ulreg", "smu", "mpu";
+            device_type = "pci";
+            bus-range = <0x00 0xff>;
+            num-lanes = <2>;
+            num-viewport = <8>;
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>,
+                     <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
+            interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "intr";
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map =
+                <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 2 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
+            clock-names = "ref", "core", "aux";
+            max-link-speed = <2>;
+        };
+    };
+...

Documentation/devicetree/bindings/pci/uniphier-pcie.txt

@@ -6,7 +6,7 @@ on Socionext UniPhier SoCs.
 UniPhier PCIe host controller is based on the Synopsys DesignWare PCI core.
 It shares common functions with the PCIe DesignWare core driver and inherits
 common properties defined in
-Documentation/devicetree/bindings/pci/designware-pcie.txt.
+Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml.
 
 Required properties:
 - compatible: Should be "socionext,uniphier-pcie".

Documentation/devicetree/bindings/phy/hisilicon,phy-hi3670-pcie.yaml

+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/hisilicon,phy-hi3670-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: HiSilicon Kirin970 PCIe PHY
+
+maintainers:
+  - Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
+
+description: |+
+  Bindings for PCIe PHY on HiSilicon Kirin 970.
+
+properties:
+  compatible:
+    const: hisilicon,hi970-pcie-phy
+
+  "#phy-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+    description: PHY Control registers
+
+  phy-supply:
+    description: The PCIe PHY power supply
+
+  clocks:
+    items:
+      - description: PCIe PHY clock
+      - description: PCIe AUX clock
+      - description: PCIe APB PHY clock
+      - description: PCIe APB SYS clock
+      - description: PCIe ACLK clock
+
+  clock-names:
+    items:
+      - const: phy_ref
+      - const: aux
+      - const: apb_phy
+      - const: apb_sys
+      - const: aclk
+
+  hisilicon,eye-diagram-param:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    description: Eye diagram for phy.
+
+required:
+  - "#phy-cells"
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - hisilicon,eye-diagram-param
+  - phy-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/hi3670-clock.h>
+
+    soc {
+      #address-cells = <2>;
+      #size-cells = <2>;
+      pcie_phy: pcie-phy@fc000000 {
+        compatible = "hisilicon,hi970-pcie-phy";
+        reg = <0x0 0xfc000000 0x0 0x80000>;
+        #phy-cells = <0>;
+        phy-supply = <&ldo33>;
+        clocks = <&crg_ctrl HI3670_CLK_GATE_PCIEPHY_REF>,
+                 <&crg_ctrl HI3670_CLK_GATE_PCIEAUX>,
+                 <&crg_ctrl HI3670_PCLK_GATE_PCIE_PHY>,
+                 <&crg_ctrl HI3670_PCLK_GATE_PCIE_SYS>,
+                 <&crg_ctrl HI3670_ACLK_GATE_PCIE>;
+        clock-names = "phy_ref", "aux",
+                      "apb_phy", "apb_sys", "aclk";
+        hisilicon,eye-diagram-param = <0xffffffff 0xffffffff
+                                       0xffffffff 0xffffffff 0xffffffff>;
+      };
+    };

Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml

@@ -23,9 +23,9 @@ description: |+
 
 properties:
   compatible:
-    oneOf:
-      - const: intel,lgm-emmc-phy
-      - const: intel,keembay-emmc-phy
+    enum:
+      - intel,lgm-emmc-phy
+      - intel,keembay-emmc-phy
 
   "#phy-cells":
     const: 0

Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.txt

---------------------------------------------------------------------
-Device Tree Bindings for the Xilinx Zynq MPSoC Power Management
---------------------------------------------------------------------
-The zynqmp-power node describes the power management configurations.
-It will control remote suspend/shutdown interfaces.
-
-Required properties:
- - compatible:		Must contain:	"xlnx,zynqmp-power"
- - interrupts:		Interrupt specifier
-
-Optional properties:
- - mbox-names	: Name given to channels seen in the 'mboxes' property.
-		  "tx" - Mailbox corresponding to transmit path
-		  "rx" - Mailbox corresponding to receive path
- - mboxes	: Standard property to specify a Mailbox. Each value of
-		  the mboxes property should contain a phandle to the
-		  mailbox controller device node and an args specifier
-		  that will be the phandle to the intended sub-mailbox
-		  child node to be used for communication. See
-		  Documentation/devicetree/bindings/mailbox/mailbox.txt
-		  for more details about the generic mailbox controller
-		  and client driver bindings. Also see
-		  Documentation/devicetree/bindings/mailbox/ \
-		  xlnx,zynqmp-ipi-mailbox.txt for typical controller that
-		  is used to communicate with this System controllers.
-
---------
-Examples
---------
-
-Example with interrupt method:
-
-firmware {
-	zynqmp_firmware: zynqmp-firmware {
-		compatible = "xlnx,zynqmp-firmware";
-		method = "smc";
-
-		zynqmp_power: zynqmp-power {
-			compatible = "xlnx,zynqmp-power";
-			interrupts = <0 35 4>;
-		};
-	};
-};
-
-Example with IPI mailbox method:
-
-firmware {
-	zynqmp_firmware: zynqmp-firmware {
-		compatible = "xlnx,zynqmp-firmware";
-		method = "smc";
-
-		zynqmp_power: zynqmp-power {
-			compatible = "xlnx,zynqmp-power";
-			interrupt-parent = <&gic>;
-			interrupts = <0 35 4>;
-			mboxes = <&ipi_mailbox_pmu0 0>,
-				 <&ipi_mailbox_pmu0 1>;
-			mbox-names = "tx", "rx";
-		};
-	};
-};

Documentation/devicetree/bindings/power/reset/xlnx,zynqmp-power.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/reset/xlnx,zynqmp-power.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Xilinx Zynq MPSoC Power Management Device Tree Bindings
+
+maintainers:
+  - Michal Simek <michal.simek@xilinx.com>
+
+description: |
+  The zynqmp-power node describes the power management configurations.
+  It will control remote suspend/shutdown interfaces.
+
+properties:
+  compatible:
+    const: "xlnx,zynqmp-power"
+
+  interrupts:
+    maxItems: 1
+
+  mboxes:
+    description: |
+      Standard property to specify a Mailbox. Each value of
+      the mboxes property should contain a phandle to the
+      mailbox controller device node and an args specifier
+      that will be the phandle to the intended sub-mailbox
+      child node to be used for communication. See
+      Documentation/devicetree/bindings/mailbox/mailbox.txt
+      for more details about the generic mailbox controller
+      and client driver bindings. Also see
+      Documentation/devicetree/bindings/mailbox/ \
+      xlnx,zynqmp-ipi-mailbox.txt for typical controller that
+      is used to communicate with this System controllers.
+    items:
+      - description: tx channel
+      - description: rx channel
+
+  mbox-names:
+    description:
+      Name given to channels seen in the 'mboxes' property.
+    items:
+      - const: tx
+      - const: rx
+
+required:
+  - compatible
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |+
+
+    // Example with interrupt method:
+
+    firmware {
+      zynqmp-firmware {
+        zynqmp-power {
+          compatible = "xlnx,zynqmp-power";
+          interrupts = <0 35 4>;
+        };
+      };
+    };
+
+  - |+
+
+    // Example with IPI mailbox method:
+
+    firmware {
+      zynqmp-firmware {
+        zynqmp-power {
+          compatible = "xlnx,zynqmp-power";
+          interrupt-parent = <&gic>;
+          interrupts = <0 35 4>;
+          mboxes = <&ipi_mailbox_pmu1 0>,
+                   <&ipi_mailbox_pmu1 1>;
+          mbox-names = "tx", "rx";
+        };
+      };
+    };
+...

Documentation/devicetree/bindings/regulator/richtek,rt6245-regulator.yaml

@@ -77,7 +77,6 @@ examples:
 
       rt6245@34 {
         compatible = "richtek,rt6245";
-        status = "okay";
         reg = <0x34>;
         enable-gpios = <&gpio26 2 0>;
 

Documentation/devicetree/bindings/regulator/vqmmc-ipq4019-regulator.yaml

@@ -39,6 +39,5 @@ examples:
       regulator-min-microvolt = <1500000>;
       regulator-max-microvolt = <3000000>;
       regulator-always-on;
-      status = "disabled";
     };
 ...

Documentation/devicetree/bindings/reset/hisilicon,hi3660-reset.yaml

@@ -72,6 +72,5 @@ examples:
         resets = <&iomcu_rst 0x20 3>;
         pinctrl-names = "default";
         pinctrl-0 = <&i2c0_pmx_func &i2c0_cfg_func>;
-        status = "disabled";
     };
 ...

Documentation/devicetree/bindings/reset/intel,rcu-gw.yaml

@@ -57,7 +57,6 @@ examples:
     };
 
     pwm: pwm@e0d00000 {
-        status = "disabled";
         compatible = "intel,lgm-pwm";
         reg = <0xe0d00000 0x30>;
         clocks = <&cgu0 1>;

Documentation/devicetree/bindings/rng/mtk-rng.yaml

@@ -21,6 +21,7 @@ properties:
           - enum:
               - mediatek,mt7622-rng
               - mediatek,mt7629-rng
+              - mediatek,mt7986-rng
               - mediatek,mt8365-rng
               - mediatek,mt8516-rng
           - const: mediatek,mt7623-rng

Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.txt

-Exynos True Random Number Generator
-
-Required properties:
-
-- compatible  : Should be "samsung,exynos5250-trng".
-- reg         : Specifies base physical address and size of the registers map.
-- clocks      : Phandle to clock-controller plus clock-specifier pair.
-- clock-names : "secss" as a clock name.
-
-Example:
-
-	rng@10830600 {
-		compatible = "samsung,exynos5250-trng";
-		reg = <0x10830600 0x100>;
-		clocks = <&clock CLK_SSS>;
-		clock-names = "secss";
-	};

Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/rng/samsung,exynos5250-trng.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Samsung Exynos SoC True Random Number Generator
+
+maintainers:
+  - Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
+  - Łukasz Stelmach <l.stelmach@samsung.com>
+
+properties:
+  compatible:
+    const: samsung,exynos5250-trng
+
+  clocks:
+    maxItems: 1
+
+  clock-names:
+    items:
+      - const: secss
+
+  reg:
+    maxItems: 1
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - reg
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/exynos5250.h>
+
+    rng@10830600 {
+        compatible = "samsung,exynos5250-trng";
+        reg = <0x10830600 0x100>;
+        clocks = <&clock CLK_SSS>;
+        clock-names = "secss";
+    };

Documentation/devicetree/bindings/rtc/microcrystal,rv3032.yaml

@@ -53,7 +53,6 @@ examples:
         rtc@51 {
             compatible = "microcrystal,rv3032";
             reg = <0x51>;
-            status = "okay";
             pinctrl-0 = <&rtc_nint_pins>;
             interrupts-extended = <&gpio1 16 IRQ_TYPE_LEVEL_HIGH>;
             trickle-resistor-ohms = <7000>;

Documentation/devicetree/bindings/serial/8250_omap.yaml

@@ -91,10 +91,11 @@ additionalProperties: false
 if:
   properties:
     compatible:
-      oneOf:
-        - const: ti,omap2-uart
-        - const: ti,omap3-uart
-        - const: ti,omap4-uart
+      contains:
+        enum:
+          - ti,omap2-uart
+          - ti,omap3-uart
+          - ti,omap4-uart
 
 then:
   properties:

Documentation/devicetree/bindings/soc/litex/litex,soc-controller.yaml

@@ -35,7 +35,6 @@ examples:
     soc_ctrl0: soc-controller@f0000000 {
         compatible = "litex,soc-controller";
         reg = <0xf0000000 0xc>;
-        status = "okay";
     };
 
 ...

Documentation/devicetree/bindings/sound/qcom,sm8250.yaml

@@ -15,9 +15,9 @@ description:
 
 properties:
   compatible:
-    oneOf:
-      - const: qcom,sm8250-sndcard
-      - const: qcom,qrb5165-rb5-sndcard
+    enum:
+      - qcom,sm8250-sndcard
+      - qcom,qrb5165-rb5-sndcard
 
   audio-routing:
     $ref: /schemas/types.yaml#/definitions/non-unique-string-array

Documentation/devicetree/bindings/sound/st,stm32-sai.yaml

@@ -180,7 +180,6 @@ examples:
       pinctrl-names = "default", "sleep";
       pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>;
       pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>;
-      status = "okay";
 
       sai2a: audio-controller@4400b004 {
         #sound-dai-cells = <0>;
@@ -190,7 +189,6 @@ examples:
         dma-names = "tx";
         clocks = <&rcc SAI2_K>;
         clock-names = "sai_ck";
-        status = "okay";
       };
     };
 

Documentation/devicetree/bindings/sound/ti,j721e-cpb-audio.yaml

@@ -127,8 +127,6 @@ examples:
         compatible = "ti,j721e-cpb-audio";
         model = "j721e-cpb";
 
-        status = "okay";
-
         ti,cpb-mcasp = <&mcasp10>;
         ti,cpb-codec = <&pcm3168a_1>;
 

Documentation/devicetree/bindings/sound/ti,j721e-cpb-ivi-audio.yaml

@@ -119,8 +119,6 @@ examples:
         compatible = "ti,j721e-cpb-ivi-audio";
         model = "j721e-cpb-ivi";
 
-        status = "okay";
-
         ti,cpb-mcasp = <&mcasp10>;
         ti,cpb-codec = <&pcm3168a_1>;
 

Documentation/devicetree/bindings/sound/tlv320adcx140.yaml

@@ -24,10 +24,10 @@ description: |
 
 properties:
   compatible:
-    oneOf:
-      - const: ti,tlv320adc3140
-      - const: ti,tlv320adc5140
-      - const: ti,tlv320adc6140
+    enum:
+      - ti,tlv320adc3140
+      - ti,tlv320adc5140
+      - ti,tlv320adc6140
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/spi/realtek,rtl-spi.yaml

@@ -15,12 +15,12 @@ allOf:
 
 properties:
   compatible:
-    oneOf:
-      - const: realtek,rtl8380-spi
-      - const: realtek,rtl8382-spi
-      - const: realtek,rtl8391-spi
-      - const: realtek,rtl8392-spi
-      - const: realtek,rtl8393-spi
+    enum:
+      - realtek,rtl8380-spi
+      - realtek,rtl8382-spi
+      - realtek,rtl8391-spi
+      - realtek,rtl8392-spi
+      - realtek,rtl8393-spi
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/timer/arm,sp804.yaml

@@ -23,9 +23,9 @@ select:
   properties:
     compatible:
       contains:
-        oneOf:
-          - const: arm,sp804
-          - const: hisilicon,sp804
+        enum:
+          - arm,sp804
+          - hisilicon,sp804
   required:
     - compatible
 

Documentation/devicetree/bindings/timer/energymicro,efm32-timer.txt

-* EFM32 timer hardware
-
-The efm32 Giant Gecko SoCs come with four 16 bit timers. Two counters can be
-connected to form a 32 bit counter. Each timer has three Compare/Capture
-channels and can be used as PWM or Quadrature Decoder. Available clock sources
-are the cpu's HFPERCLK (with a 10-bit prescaler) or an external pin.
-
-Required properties:
-- compatible : Should be "energymicro,efm32-timer"
-- reg : Address and length of the register set
-- clocks : Should contain a reference to the HFPERCLK
-
-Optional properties:
-- interrupts : Reference to the timer interrupt
-
-Example:
-
-timer@40010c00 {
-	compatible = "energymicro,efm32-timer";
-	reg = <0x40010c00 0x400>;
-	interrupts = <14>;
-	clocks = <&cmu clk_HFPERCLKTIMER3>;
-};

Documentation/devicetree/bindings/trivial-devices.yaml

@@ -147,6 +147,8 @@ properties:
           - maxim,ds1803-100
             # Low-Power, 4-/12-Channel, 2-Wire Serial, 12-Bit ADCs
           - maxim,max1237
+            # Temperature Sensor, I2C interface
+          - maxim,max1619
             # 10-bit 10 kOhm linear programable voltage divider
           - maxim,max5481
             # 10-bit 50 kOhm linear programable voltage divider

Documentation/devicetree/bindings/vendor-prefixes.yaml

@@ -567,6 +567,8 @@ patternProperties:
     description: ITE Tech. Inc.
   "^itead,.*":
     description: ITEAD Intelligent Systems Co.Ltd
+  "^itian,.*":
+    description: ITian Corporation
   "^iwave,.*":
     description: iWave Systems Technologies Pvt. Ltd.
   "^jdi,.*":
@@ -1121,6 +1123,10 @@ patternProperties:
   "^st-ericsson,.*":
     description: ST-Ericsson
     deprecated: true
+  "^storlink,.*":
+    description: StorLink Semiconductors, Inc.
+  "^storm,.*":
+    description: Storm Semiconductor, Inc.
   "^summit,.*":
     description: Summit microelectronics
   "^sunchip,.*":
@@ -1153,6 +1159,8 @@ patternProperties:
     description: TechNexion
   "^technologic,.*":
     description: Technologic Systems
+  "^teltonika,.*":
+    description: Teltonika Networks
   "^tempo,.*":
     description: Tempo Semiconductor
   "^techstar,.*":
@@ -1175,6 +1183,8 @@ patternProperties:
     description: Tecon Microprocessor Technologies, LLC.
   "^topeet,.*":
     description: Topeet
+  "^topic,.*":
+    description: Topic Embedded Systems
   "^toppoly,.*":
     description: TPO (deprecated, use tpo)
     deprecated: true
@@ -1280,6 +1290,8 @@ patternProperties:
     description: Shenzhen whwave Electronics, Inc.
   "^wi2wi,.*":
     description: Wi2Wi, Inc.
+  "^wiligear,.*":
+    description: Wiligear, Ltd.
   "^winbond,.*":
     description: Winbond Electronics corp.
   "^winstar,.*":

MAINTAINERS

@@ -1395,7 +1395,7 @@ F:	Documentation/devicetree/bindings/arm/arm,integrator.yaml
 F:	Documentation/devicetree/bindings/arm/arm,realview.yaml
 F:	Documentation/devicetree/bindings/arm/arm,versatile.yaml
 F:	Documentation/devicetree/bindings/arm/arm,vexpress-juno.yaml
-F:	Documentation/devicetree/bindings/auxdisplay/arm-charlcd.txt
+F:	Documentation/devicetree/bindings/auxdisplay/arm,versatile-lcd.yaml
 F:	Documentation/devicetree/bindings/clock/arm,syscon-icst.yaml
 F:	Documentation/devicetree/bindings/i2c/i2c-versatile.txt
 F:	Documentation/devicetree/bindings/interrupt-controller/arm,versatile-fpga-irq.txt
@@ -3869,7 +3869,7 @@ M:	Markus Mayer <mmayer@broadcom.com>
 M:	bcm-kernel-feedback-list@broadcom.com
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
-F:	Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.txt
+F:	Documentation/devicetree/bindings/memory-controllers/brcm,dpfe-cpu.yaml
 F:	drivers/memory/brcmstb_dpfe.c
 
 BROADCOM STB NAND FLASH DRIVER
@@ -5595,7 +5595,7 @@ M:	Lukasz Luba <lukasz.luba@arm.com>
 L:	linux-pm@vger.kernel.org
 L:	linux-samsung-soc@vger.kernel.org
 S:	Maintained
-F:	Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt
+F:	Documentation/devicetree/bindings/memory-controllers/samsung,exynos5422-dmc.yaml
 F:	drivers/memory/samsung/exynos5422-dmc.c
 
 DME1737 HARDWARE MONITOR DRIVER
@@ -6604,6 +6604,7 @@ EDAC-ARMADA
 M:	Jan Luebbe <jlu@pengutronix.de>
 L:	linux-edac@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/memory-controllers/marvell,mvebu-sdram-controller.yaml
 F:	drivers/edac/armada_xp_*
 
 EDAC-AST2500
@@ -9096,7 +9097,7 @@ F:	drivers/usb/atm/ueagle-atm.c
 IMGTEC ASCII LCD DRIVER
 M:	Paul Burton <paulburton@kernel.org>
 S:	Maintained
-F:	Documentation/devicetree/bindings/auxdisplay/img-ascii-lcd.txt
+F:	Documentation/devicetree/bindings/auxdisplay/img,ascii-lcd.yaml
 F:	drivers/auxdisplay/img-ascii-lcd.c
 
 IMGTEC IR DECODER DRIVER
@@ -14281,7 +14282,7 @@ M:	Lucas Stach <l.stach@pengutronix.de>
 L:	linux-pci@vger.kernel.org
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
-F:	Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+F:	Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.yaml
 F:	drivers/pci/controller/dwc/*imx6*
 
 PCI DRIVER FOR FU740
@@ -14369,7 +14370,8 @@ M:	Jingoo Han <jingoohan1@gmail.com>
 M:	Gustavo Pimentel <gustavo.pimentel@synopsys.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
-F:	Documentation/devicetree/bindings/pci/designware-pcie.txt
+F:	Documentation/devicetree/bindings/pci/snps,dw-pcie.yaml
+F:	Documentation/devicetree/bindings/pci/snps,dw-pcie-ep.yaml
 F:	drivers/pci/controller/dwc/*designware*
 
 PCI DRIVER FOR TI DRA7XX/J721E
@@ -14506,7 +14508,7 @@ M:	Xiaowei Song <songxiaowei@hisilicon.com>
 M:	Binghui Wang <wangbinghui@hisilicon.com>
 L:	linux-pci@vger.kernel.org
 S:	Maintained
-F:	Documentation/devicetree/bindings/pci/kirin-pcie.txt
+F:	Documentation/devicetree/bindings/pci/hisilicon,kirin-pcie.yaml
 F:	drivers/pci/controller/dwc/pcie-kirin.c
 
 PCIE DRIVER FOR HISILICON STB
@@ -16412,7 +16414,7 @@ SAMSUNG EXYNOS TRUE RANDOM NUMBER GENERATOR (TRNG) DRIVER
 M:	Łukasz Stelmach <l.stelmach@samsung.com>
 L:	linux-samsung-soc@vger.kernel.org
 S:	Maintained
-F:	Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.txt
+F:	Documentation/devicetree/bindings/rng/samsung,exynos5250-trng.yaml
 F:	drivers/char/hw_random/exynos-trng.c
 
 SAMSUNG FRAMEBUFFER DRIVER

arch/arm64/mm/init.c

@@ -124,57 +124,6 @@ static void __init reserve_crashkernel(void)
 }
 #endif /* CONFIG_KEXEC_CORE */
 
-#ifdef CONFIG_CRASH_DUMP
-static int __init early_init_dt_scan_elfcorehdr(unsigned long node,
-		const char *uname, int depth, void *data)
-{
-	const __be32 *reg;
-	int len;
-
-	if (depth != 1 || strcmp(uname, "chosen") != 0)
-		return 0;
-
-	reg = of_get_flat_dt_prop(node, "linux,elfcorehdr", &len);
-	if (!reg || (len < (dt_root_addr_cells + dt_root_size_cells)))
-		return 1;
-
-	elfcorehdr_addr = dt_mem_next_cell(dt_root_addr_cells, &reg);
-	elfcorehdr_size = dt_mem_next_cell(dt_root_size_cells, &reg);
-
-	return 1;
-}
-
-/*
- * reserve_elfcorehdr() - reserves memory for elf core header
- *
- * This function reserves the memory occupied by an elf core header
- * described in the device tree. This region contains all the
- * information about primary kernel's core image and is used by a dump
- * capture kernel to access the system memory on primary kernel.
- */
-static void __init reserve_elfcorehdr(void)
-{
-	of_scan_flat_dt(early_init_dt_scan_elfcorehdr, NULL);
-
-	if (!elfcorehdr_size)
-		return;
-
-	if (memblock_is_region_reserved(elfcorehdr_addr, elfcorehdr_size)) {
-		pr_warn("elfcorehdr is overlapped\n");
-		return;
-	}
-
-	memblock_reserve(elfcorehdr_addr, elfcorehdr_size);
-
-	pr_info("Reserving %lldKB of memory at 0x%llx for elfcorehdr\n",
-		elfcorehdr_size >> 10, elfcorehdr_addr);
-}
-#else
-static void __init reserve_elfcorehdr(void)
-{
-}
-#endif /* CONFIG_CRASH_DUMP */
-
 /*
  * Return the maximum physical address for a zone accessible by the given bits
  * limit. If DRAM starts above 32-bit, expand the zone to the maximum
@@ -285,45 +234,10 @@ static int __init early_mem(char *p)
 }
 early_param("mem", early_mem);
 
-static int __init early_init_dt_scan_usablemem(unsigned long node,
-		const char *uname, int depth, void *data)
-{
-	struct memblock_region *usablemem = data;
-	const __be32 *reg;
-	int len;
-
-	if (depth != 1 || strcmp(uname, "chosen") != 0)
-		return 0;
-
-	reg = of_get_flat_dt_prop(node, "linux,usable-memory-range", &len);
-	if (!reg || (len < (dt_root_addr_cells + dt_root_size_cells)))
-		return 1;
-
-	usablemem->base = dt_mem_next_cell(dt_root_addr_cells, &reg);
-	usablemem->size = dt_mem_next_cell(dt_root_size_cells, &reg);
-
-	return 1;
-}
-
-static void __init fdt_enforce_memory_region(void)
-{
-	struct memblock_region reg = {
-		.size = 0,
-	};
-
-	of_scan_flat_dt(early_init_dt_scan_usablemem, &reg);
-
-	if (reg.size)
-		memblock_cap_memory_range(reg.base, reg.size);
-}
-
 void __init arm64_memblock_init(void)
 {
 	const s64 linear_region_size = PAGE_END - _PAGE_OFFSET(vabits_actual);
 
-	/* Handle linux,usable-memory-range property */
-	fdt_enforce_memory_region();
-
 	/* Remove memory above our supported physical address size */
 	memblock_remove(1ULL << PHYS_MASK_SHIFT, ULLONG_MAX);
 
@@ -432,8 +346,6 @@ void __init arm64_memblock_init(void)
 
 	early_init_fdt_scan_reserved_mem();
 
-	reserve_elfcorehdr();
-
 	high_memory = __va(memblock_end_of_DRAM() - 1) + 1;
 }
 

arch/riscv/mm/init.c

@@ -860,26 +860,6 @@ static void __init reserve_crashkernel(void)
 }
 #endif /* CONFIG_KEXEC_CORE */
 
-#ifdef CONFIG_CRASH_DUMP
-/*
- * We keep track of the ELF core header of the crashed
- * kernel with a reserved-memory region with compatible
- * string "linux,elfcorehdr". Here we register a callback
- * to populate elfcorehdr_addr/size when this region is
- * present. Note that this region will be marked as
- * reserved once we call early_init_fdt_scan_reserved_mem()
- * later on.
- */
-static int __init elfcore_hdr_setup(struct reserved_mem *rmem)
-{
-	elfcorehdr_addr = rmem->base;
-	elfcorehdr_size = rmem->size;
-	return 0;
-}
-
-RESERVEDMEM_OF_DECLARE(elfcorehdr, "linux,elfcorehdr", elfcore_hdr_setup);
-#endif
-
 void __init paging_init(void)
 {
 	setup_bootmem();

drivers/of/base.c

@@ -708,9 +708,7 @@ static struct device_node *__of_get_next_child(const struct device_node *node,
 		return NULL;
 
 	next = prev ? prev->sibling : node->child;
-	for (; next; next = next->sibling)
-		if (of_node_get(next))
-			break;
+	of_node_get(next);
 	of_node_put(prev);
 	return next;
 }

drivers/of/fdt.c

@@ -8,6 +8,7 @@
 
 #define pr_fmt(fmt)	"OF: fdt: " fmt
 
+#include <linux/crash_dump.h>
 #include <linux/crc32.h>
 #include <linux/kernel.h>
 #include <linux/initrd.h>
@@ -193,16 +194,12 @@ static void populate_properties(const void *blob,
 			pp->length = len;
 			pp->value  = pp + 1;
 			*pprev     = pp;
-			pprev      = &pp->next;
 			memcpy(pp->value, ps, len - 1);
 			((char *)pp->value)[len - 1] = 0;
 			pr_debug("fixed up name for %s -> %s\n",
 				 nodename, (char *)pp->value);
 		}
 	}
-
-	if (!dryrun)
-		*pprev = NULL;
 }
 
 static int populate_node(const void *blob,
@@ -479,6 +476,22 @@ void *initial_boot_params __ro_after_init;
 
 static u32 of_fdt_crc32;
 
+static int __init early_init_dt_reserve_memory_arch(phys_addr_t base,
+					phys_addr_t size, bool nomap)
+{
+	if (nomap) {
+		/*
+		 * If the memory is already reserved (by another region), we
+		 * should not allow it to be marked nomap.
+		 */
+		if (memblock_is_region_reserved(base, size))
+			return -EBUSY;
+
+		return memblock_mark_nomap(base, size);
+	}
+	return memblock_reserve(base, size);
+}
+
 /*
  * __reserved_mem_reserve_reg() - reserve all memory described in 'reg' property
  */
@@ -585,6 +598,30 @@ static int __init __fdt_scan_reserved_mem(unsigned long node, const char *uname,
 	return 0;
 }
 
+/*
+ * fdt_reserve_elfcorehdr() - reserves memory for elf core header
+ *
+ * This function reserves the memory occupied by an elf core header
+ * described in the device tree. This region contains all the
+ * information about primary kernel's core image and is used by a dump
+ * capture kernel to access the system memory on primary kernel.
+ */
+static void __init fdt_reserve_elfcorehdr(void)
+{
+	if (!IS_ENABLED(CONFIG_CRASH_DUMP) || !elfcorehdr_size)
+		return;
+
+	if (memblock_is_region_reserved(elfcorehdr_addr, elfcorehdr_size)) {
+		pr_warn("elfcorehdr is overlapped\n");
+		return;
+	}
+
+	memblock_reserve(elfcorehdr_addr, elfcorehdr_size);
+
+	pr_info("Reserving %llu KiB of memory at 0x%llx for elfcorehdr\n",
+		elfcorehdr_size >> 10, elfcorehdr_addr);
+}
+
 /**
  * early_init_fdt_scan_reserved_mem() - create reserved memory regions
  *
@@ -610,6 +647,7 @@ void __init early_init_fdt_scan_reserved_mem(void)
 
 	of_scan_flat_dt(__fdt_scan_reserved_mem, NULL);
 	fdt_init_reserved_mem();
+	fdt_reserve_elfcorehdr();
 }
 
 /**
@@ -858,7 +896,6 @@ const void * __init of_flat_dt_match_machine(const void *default_match,
 	return best_data;
 }
 
-#ifdef CONFIG_BLK_DEV_INITRD
 static void __early_init_dt_declare_initrd(unsigned long start,
 					   unsigned long end)
 {
@@ -884,6 +921,9 @@ static void __init early_init_dt_check_for_initrd(unsigned long node)
 	int len;
 	const __be32 *prop;
 
+	if (!IS_ENABLED(CONFIG_BLK_DEV_INITRD))
+		return;
+
 	pr_debug("Looking for initrd properties... ");
 
 	prop = of_get_flat_dt_prop(node, "linux,initrd-start", &len);
@@ -902,11 +942,58 @@ static void __init early_init_dt_check_for_initrd(unsigned long node)
 
 	pr_debug("initrd_start=0x%llx  initrd_end=0x%llx\n", start, end);
 }
-#else
-static inline void early_init_dt_check_for_initrd(unsigned long node)
+
+/**
+ * early_init_dt_check_for_elfcorehdr - Decode elfcorehdr location from flat
+ * tree
+ * @node: reference to node containing elfcorehdr location ('chosen')
+ */
+static void __init early_init_dt_check_for_elfcorehdr(unsigned long node)
+{
+	const __be32 *prop;
+	int len;
+
+	if (!IS_ENABLED(CONFIG_CRASH_DUMP))
+		return;
+
+	pr_debug("Looking for elfcorehdr property... ");
+
+	prop = of_get_flat_dt_prop(node, "linux,elfcorehdr", &len);
+	if (!prop || (len < (dt_root_addr_cells + dt_root_size_cells)))
+		return;
+
+	elfcorehdr_addr = dt_mem_next_cell(dt_root_addr_cells, &prop);
+	elfcorehdr_size = dt_mem_next_cell(dt_root_size_cells, &prop);
+
+	pr_debug("elfcorehdr_start=0x%llx elfcorehdr_size=0x%llx\n",
+		 elfcorehdr_addr, elfcorehdr_size);
+}
+
+static phys_addr_t cap_mem_addr;
+static phys_addr_t cap_mem_size;
+
+/**
+ * early_init_dt_check_for_usable_mem_range - Decode usable memory range
+ * location from flat tree
+ * @node: reference to node containing usable memory range location ('chosen')
+ */
+static void __init early_init_dt_check_for_usable_mem_range(unsigned long node)
 {
+	const __be32 *prop;
+	int len;
+
+	pr_debug("Looking for usable-memory-range property... ");
+
+	prop = of_get_flat_dt_prop(node, "linux,usable-memory-range", &len);
+	if (!prop || (len < (dt_root_addr_cells + dt_root_size_cells)))
+		return;
+
+	cap_mem_addr = dt_mem_next_cell(dt_root_addr_cells, &prop);
+	cap_mem_size = dt_mem_next_cell(dt_root_size_cells, &prop);
+
+	pr_debug("cap_mem_start=%pa cap_mem_size=%pa\n", &cap_mem_addr,
+		 &cap_mem_size);
 }
-#endif /* CONFIG_BLK_DEV_INITRD */
 
 #ifdef CONFIG_SERIAL_EARLYCON
 
@@ -1033,7 +1120,7 @@ int __init early_init_dt_scan_memory(unsigned long node, const char *uname,
 		if (!hotpluggable)
 			continue;
 
-		if (early_init_dt_mark_hotplug_memory_arch(base, size))
+		if (memblock_mark_hotplug(base, size))
 			pr_warn("failed to mark hotplug range 0x%llx - 0x%llx\n",
 				base, base + size);
 	}
@@ -1055,6 +1142,8 @@ int __init early_init_dt_scan_chosen(unsigned long node, const char *uname,
 		return 0;
 
 	early_init_dt_check_for_initrd(node);
+	early_init_dt_check_for_elfcorehdr(node);
+	early_init_dt_check_for_usable_mem_range(node);
 
 	/* Retrieve command line */
 	p = of_get_flat_dt_prop(node, "bootargs", &l);
@@ -1146,27 +1235,6 @@ void __init __weak early_init_dt_add_memory_arch(u64 base, u64 size)
 	memblock_add(base, size);
 }
 
-int __init __weak early_init_dt_mark_hotplug_memory_arch(u64 base, u64 size)
-{
-	return memblock_mark_hotplug(base, size);
-}
-
-int __init __weak early_init_dt_reserve_memory_arch(phys_addr_t base,
-					phys_addr_t size, bool nomap)
-{
-	if (nomap) {
-		/*
-		 * If the memory is already reserved (by another region), we
-		 * should not allow it to be marked nomap.
-		 */
-		if (memblock_is_region_reserved(base, size))
-			return -EBUSY;
-
-		return memblock_mark_nomap(base, size);
-	}
-	return memblock_reserve(base, size);
-}
-
 static void * __init early_init_dt_alloc_memory_arch(u64 size, u64 align)
 {
 	void *ptr = memblock_alloc(size, align);
@@ -1199,16 +1267,19 @@ void __init early_init_dt_scan_nodes(void)
 {
 	int rc = 0;
 
+	/* Initialize {size,address}-cells info */
+	of_scan_flat_dt(early_init_dt_scan_root, NULL);
+
 	/* Retrieve various information from the /chosen node */
 	rc = of_scan_flat_dt(early_init_dt_scan_chosen, boot_command_line);
 	if (!rc)
 		pr_warn("No chosen node found, continuing without\n");
 
-	/* Initialize {size,address}-cells info */
-	of_scan_flat_dt(early_init_dt_scan_root, NULL);
-
 	/* Setup memory, calling early_init_dt_add_memory_arch */
 	of_scan_flat_dt(early_init_dt_scan_memory, NULL);
+
+	/* Handle linux,usable-memory-range property */
+	memblock_cap_memory_range(cap_mem_addr, cap_mem_size);
 }
 
 bool __init early_init_dt_scan(void *params)

drivers/of/kexec.c

@@ -18,14 +18,6 @@
 #include <linux/random.h>
 #include <linux/types.h>
 
-/* relevant device tree properties */
-#define FDT_PROP_KEXEC_ELFHDR	"linux,elfcorehdr"
-#define FDT_PROP_MEM_RANGE	"linux,usable-memory-range"
-#define FDT_PROP_INITRD_START	"linux,initrd-start"
-#define FDT_PROP_INITRD_END	"linux,initrd-end"
-#define FDT_PROP_BOOTARGS	"bootargs"
-#define FDT_PROP_KASLR_SEED	"kaslr-seed"
-#define FDT_PROP_RNG_SEED	"rng-seed"
 #define RNG_SEED_SIZE		128
 
 /*
@@ -310,10 +302,10 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 		goto out;
 	}
 
-	ret = fdt_delprop(fdt, chosen_node, FDT_PROP_KEXEC_ELFHDR);
+	ret = fdt_delprop(fdt, chosen_node, "linux,elfcorehdr");
 	if (ret && ret != -FDT_ERR_NOTFOUND)
 		goto out;
-	ret = fdt_delprop(fdt, chosen_node, FDT_PROP_MEM_RANGE);
+	ret = fdt_delprop(fdt, chosen_node, "linux,usable-memory-range");
 	if (ret && ret != -FDT_ERR_NOTFOUND)
 		goto out;
 
@@ -347,12 +339,12 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 
 	/* add initrd-* */
 	if (initrd_load_addr) {
-		ret = fdt_setprop_u64(fdt, chosen_node, FDT_PROP_INITRD_START,
+		ret = fdt_setprop_u64(fdt, chosen_node, "linux,initrd-start",
 				      initrd_load_addr);
 		if (ret)
 			goto out;
 
-		ret = fdt_setprop_u64(fdt, chosen_node, FDT_PROP_INITRD_END,
+		ret = fdt_setprop_u64(fdt, chosen_node, "linux,initrd-end",
 				      initrd_load_addr + initrd_len);
 		if (ret)
 			goto out;
@@ -362,11 +354,11 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 			goto out;
 
 	} else {
-		ret = fdt_delprop(fdt, chosen_node, FDT_PROP_INITRD_START);
+		ret = fdt_delprop(fdt, chosen_node, "linux,initrd-start");
 		if (ret && (ret != -FDT_ERR_NOTFOUND))
 			goto out;
 
-		ret = fdt_delprop(fdt, chosen_node, FDT_PROP_INITRD_END);
+		ret = fdt_delprop(fdt, chosen_node, "linux,initrd-end");
 		if (ret && (ret != -FDT_ERR_NOTFOUND))
 			goto out;
 	}
@@ -374,8 +366,7 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 	if (image->type == KEXEC_TYPE_CRASH) {
 		/* add linux,elfcorehdr */
 		ret = fdt_appendprop_addrrange(fdt, 0, chosen_node,
-				FDT_PROP_KEXEC_ELFHDR,
-				image->elf_load_addr,
+				"linux,elfcorehdr", image->elf_load_addr,
 				image->elf_headers_sz);
 		if (ret)
 			goto out;
@@ -391,8 +382,7 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 
 		/* add linux,usable-memory-range */
 		ret = fdt_appendprop_addrrange(fdt, 0, chosen_node,
-				FDT_PROP_MEM_RANGE,
-				crashk_res.start,
+				"linux,usable-memory-range", crashk_res.start,
 				crashk_res.end - crashk_res.start + 1);
 		if (ret)
 			goto out;
@@ -400,17 +390,17 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 
 	/* add bootargs */
 	if (cmdline) {
-		ret = fdt_setprop_string(fdt, chosen_node, FDT_PROP_BOOTARGS, cmdline);
+		ret = fdt_setprop_string(fdt, chosen_node, "bootargs", cmdline);
 		if (ret)
 			goto out;
 	} else {
-		ret = fdt_delprop(fdt, chosen_node, FDT_PROP_BOOTARGS);
+		ret = fdt_delprop(fdt, chosen_node, "bootargs");
 		if (ret && (ret != -FDT_ERR_NOTFOUND))
 			goto out;
 	}
 
 	/* add kaslr-seed */
-	ret = fdt_delprop(fdt, chosen_node, FDT_PROP_KASLR_SEED);
+	ret = fdt_delprop(fdt, chosen_node, "kaslr-seed");
 	if (ret == -FDT_ERR_NOTFOUND)
 		ret = 0;
 	else if (ret)
@@ -419,26 +409,26 @@ void *of_kexec_alloc_and_setup_fdt(const struct kimage *image,
 	if (rng_is_initialized()) {
 		u64 seed = get_random_u64();
 
-		ret = fdt_setprop_u64(fdt, chosen_node, FDT_PROP_KASLR_SEED, seed);
+		ret = fdt_setprop_u64(fdt, chosen_node, "kaslr-seed", seed);
 		if (ret)
 			goto out;
 	} else {
 		pr_notice("RNG is not initialised: omitting \"%s\" property\n",
-				FDT_PROP_KASLR_SEED);
+			  "kaslr-seed");
 	}
 
 	/* add rng-seed */
 	if (rng_is_initialized()) {
 		void *rng_seed;
 
-		ret = fdt_setprop_placeholder(fdt, chosen_node, FDT_PROP_RNG_SEED,
+		ret = fdt_setprop_placeholder(fdt, chosen_node, "rng-seed",
 				RNG_SEED_SIZE, &rng_seed);
 		if (ret)
 			goto out;
 		get_random_bytes(rng_seed, RNG_SEED_SIZE);
 	} else {
 		pr_notice("RNG is not initialised: omitting \"%s\" property\n",
-				FDT_PROP_RNG_SEED);
+			  "rng-seed");
 	}
 
 	ret = fdt_setprop(fdt, chosen_node, "linux,booted-from-kexec", NULL, 0);

drivers/of/kobj.c

@@ -119,7 +119,7 @@ int __of_attach_node_sysfs(struct device_node *np)
 	struct property *pp;
 	int rc;
 
-	if (!of_kset)
+	if (!IS_ENABLED(CONFIG_SYSFS) || !of_kset)
 		return 0;
 
 	np->kobj.kset = of_kset;

drivers/of/property.c

@@ -1287,6 +1287,11 @@ DEFINE_SIMPLE_PROP(pinctrl6, "pinctrl-6", NULL)
 DEFINE_SIMPLE_PROP(pinctrl7, "pinctrl-7", NULL)
 DEFINE_SIMPLE_PROP(pinctrl8, "pinctrl-8", NULL)
 DEFINE_SIMPLE_PROP(remote_endpoint, "remote-endpoint", NULL)
+DEFINE_SIMPLE_PROP(pwms, "pwms", "#pwm-cells")
+DEFINE_SIMPLE_PROP(resets, "resets", "#reset-cells")
+DEFINE_SIMPLE_PROP(leds, "leds", NULL)
+DEFINE_SIMPLE_PROP(backlight, "backlight", NULL)
+DEFINE_SIMPLE_PROP(phy_handle, "phy-handle", NULL)
 DEFINE_SUFFIX_PROP(regulators, "-supply", NULL)
 DEFINE_SUFFIX_PROP(gpio, "-gpio", "#gpio-cells")
 
@@ -1371,6 +1376,11 @@ static const struct supplier_bindings of_supplier_bindings[] = {
 	{ .parse_prop = parse_pinctrl7, },
 	{ .parse_prop = parse_pinctrl8, },
 	{ .parse_prop = parse_remote_endpoint, .node_not_dev = true, },
+	{ .parse_prop = parse_pwms, },
+	{ .parse_prop = parse_resets, },
+	{ .parse_prop = parse_leds, },
+	{ .parse_prop = parse_backlight, },
+	{ .parse_prop = parse_phy_handle, },
 	{ .parse_prop = parse_gpio_compat, },
 	{ .parse_prop = parse_interrupts, },
 	{ .parse_prop = parse_regulators, },

include/dt-bindings/clock/zx296718-clock.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2015 - 2016 ZTE Corporation.
- */
-#ifndef __DT_BINDINGS_CLOCK_ZX296718_H
-#define __DT_BINDINGS_CLOCK_ZX296718_H
-
-/* PLL */
-#define ZX296718_PLL_CPU	1
-#define ZX296718_PLL_MAC	2
-#define ZX296718_PLL_MM0	3
-#define ZX296718_PLL_MM1	4
-#define ZX296718_PLL_VGA	5
-#define ZX296718_PLL_DDR	6
-#define ZX296718_PLL_AUDIO	7
-#define ZX296718_PLL_HSIC	8
-#define CPU_DBG_GATE		9
-#define A72_GATE		10
-#define CPU_PERI_GATE		11
-#define A53_GATE		12
-#define DDR1_GATE		13
-#define DDR0_GATE		14
-#define SD1_WCLK		15
-#define SD1_AHB			16
-#define SD0_WCLK		17
-#define SD0_AHB			18
-#define EMMC_WCLK		19
-#define EMMC_NAND_AXI		20
-#define NAND_WCLK		21
-#define EMMC_NAND_AHB		22
-#define LSP1_148M5		23
-#define LSP1_99M		24
-#define LSP1_24M		25
-#define LSP0_74M25		26
-#define LSP0_32K		27
-#define LSP0_148M5		28
-#define LSP0_99M		29
-#define LSP0_24M		30
-#define DEMUX_AXI		31
-#define DEMUX_APB		32
-#define DEMUX_148M5		33
-#define DEMUX_108M		34
-#define AUDIO_APB		35
-#define AUDIO_99M		36
-#define AUDIO_24M		37
-#define AUDIO_16M384		38
-#define AUDIO_32K		39
-#define WDT_WCLK		40
-#define TIMER_WCLK		41
-#define VDE_ACLK		42
-#define VCE_ACLK		43
-#define HDE_ACLK		44
-#define GPU_ACLK		45
-#define SAPPU_ACLK		46
-#define SAPPU_WCLK		47
-#define VOU_ACLK		48
-#define VOU_MAIN_WCLK		49
-#define VOU_AUX_WCLK		50
-#define VOU_PPU_WCLK		51
-#define MIPI_CFG_CLK		52
-#define VGA_I2C_WCLK		53
-#define MIPI_REF_CLK		54
-#define HDMI_OSC_CEC		55
-#define HDMI_OSC_CLK		56
-#define HDMI_XCLK		57
-#define VIU_M0_ACLK		58
-#define VIU_M1_ACLK		59
-#define VIU_WCLK		60
-#define VIU_JPEG_WCLK		61
-#define VIU_CFG_CLK		62
-#define TS_SYS_WCLK		63
-#define TS_SYS_108M		64
-#define USB20_HCLK		65
-#define USB20_PHY_CLK		66
-#define USB21_HCLK		67
-#define USB21_PHY_CLK		68
-#define GMAC_RMIICLK		69
-#define GMAC_PCLK		70
-#define GMAC_ACLK		71
-#define GMAC_RFCLK		72
-#define TEMPSENSOR_GATE		73
-
-#define TOP_NR_CLKS		74
-
-
-#define LSP0_TIMER3_PCLK	1
-#define LSP0_TIMER3_WCLK	2
-#define LSP0_TIMER4_PCLK	3
-#define LSP0_TIMER4_WCLK	4
-#define LSP0_TIMER5_PCLK	5
-#define LSP0_TIMER5_WCLK	6
-#define LSP0_UART3_PCLK		7
-#define LSP0_UART3_WCLK		8
-#define LSP0_UART1_PCLK		9
-#define LSP0_UART1_WCLK		10
-#define LSP0_UART2_PCLK		11
-#define LSP0_UART2_WCLK		12
-#define LSP0_SPIFC0_PCLK	13
-#define LSP0_SPIFC0_WCLK	14
-#define LSP0_I2C4_PCLK		15
-#define LSP0_I2C4_WCLK		16
-#define LSP0_I2C5_PCLK		17
-#define LSP0_I2C5_WCLK		18
-#define LSP0_SSP0_PCLK		19
-#define LSP0_SSP0_WCLK		20
-#define LSP0_SSP1_PCLK		21
-#define LSP0_SSP1_WCLK		22
-#define LSP0_USIM_PCLK		23
-#define LSP0_USIM_WCLK		24
-#define LSP0_GPIO_PCLK		25
-#define LSP0_GPIO_WCLK		26
-#define LSP0_I2C3_PCLK		27
-#define LSP0_I2C3_WCLK		28
-
-#define LSP0_NR_CLKS		29
-
-
-#define LSP1_UART4_PCLK		1
-#define LSP1_UART4_WCLK		2
-#define LSP1_UART5_PCLK		3
-#define LSP1_UART5_WCLK		4
-#define LSP1_PWM_PCLK		5
-#define LSP1_PWM_WCLK		6
-#define LSP1_I2C2_PCLK		7
-#define LSP1_I2C2_WCLK		8
-#define LSP1_SSP2_PCLK		9
-#define LSP1_SSP2_WCLK		10
-#define LSP1_SSP3_PCLK		11
-#define LSP1_SSP3_WCLK		12
-#define LSP1_SSP4_PCLK		13
-#define LSP1_SSP4_WCLK		14
-#define LSP1_USIM1_PCLK		15
-#define LSP1_USIM1_WCLK		16
-
-#define LSP1_NR_CLKS		17
-
-
-#define AUDIO_I2S0_WCLK		1
-#define AUDIO_I2S0_PCLK		2
-#define AUDIO_I2S1_WCLK		3
-#define AUDIO_I2S1_PCLK		4
-#define AUDIO_I2S2_WCLK		5
-#define AUDIO_I2S2_PCLK		6
-#define AUDIO_I2S3_WCLK		7
-#define AUDIO_I2S3_PCLK		8
-#define AUDIO_I2C0_WCLK		9
-#define AUDIO_I2C0_PCLK		10
-#define AUDIO_SPDIF0_WCLK	11
-#define AUDIO_SPDIF0_PCLK	12
-#define AUDIO_SPDIF1_WCLK	13
-#define AUDIO_SPDIF1_PCLK	14
-#define AUDIO_TIMER_WCLK	15
-#define AUDIO_TIMER_PCLK	16
-#define AUDIO_TDM_WCLK		17
-#define AUDIO_TDM_PCLK		18
-#define AUDIO_TS_PCLK		19
-#define I2S0_WCLK_MUX		20
-#define I2S1_WCLK_MUX		21
-#define I2S2_WCLK_MUX		22
-#define I2S3_WCLK_MUX		23
-
-#define AUDIO_NR_CLKS		24
-
-#endif

include/dt-bindings/soc/zte,pm_domains.h

-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) 2017 Linaro Ltd.
- *
- * Author: Baoyou Xie <baoyou.xie@linaro.org>
- */
-
-#ifndef _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H
-#define _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H
-
-#define DM_ZX296718_SAPPU	0
-#define DM_ZX296718_VDE		1  /* g1v6 */
-#define DM_ZX296718_VCE		2  /* h1v6 */
-#define DM_ZX296718_HDE		3  /* g2v2 */
-#define DM_ZX296718_VIU		4
-#define DM_ZX296718_USB20	5
-#define DM_ZX296718_USB21	6
-#define DM_ZX296718_USB30	7
-#define DM_ZX296718_HSIC	8
-#define DM_ZX296718_GMAC	9
-#define DM_ZX296718_TS		10
-#define DM_ZX296718_VOU		11
-
-#endif /* _DT_BINDINGS_SOC_ZTE_PM_DOMAINS_H */

include/linux/crash_dump.h

@@ -10,13 +10,14 @@
 
 #include <linux/pgtable.h> /* for pgprot_t */
 
-#ifdef CONFIG_CRASH_DUMP
+/* For IS_ENABLED(CONFIG_CRASH_DUMP) */
 #define ELFCORE_ADDR_MAX	(-1ULL)
 #define ELFCORE_ADDR_ERR	(-2ULL)
 
 extern unsigned long long elfcorehdr_addr;
 extern unsigned long long elfcorehdr_size;
 
+#ifdef CONFIG_CRASH_DUMP
 extern int elfcorehdr_alloc(unsigned long long *addr, unsigned long long *size);
 extern void elfcorehdr_free(unsigned long long addr);
 extern ssize_t elfcorehdr_read(char *buf, size_t count, u64 *ppos);

include/linux/of_fdt.h

@@ -67,9 +67,6 @@ extern void early_init_fdt_scan_reserved_mem(void);
 extern void early_init_fdt_reserve_self(void);
 extern void __init early_init_dt_scan_chosen_arch(unsigned long node);
 extern void early_init_dt_add_memory_arch(u64 base, u64 size);
-extern int early_init_dt_mark_hotplug_memory_arch(u64 base, u64 size);
-extern int early_init_dt_reserve_memory_arch(phys_addr_t base, phys_addr_t size,
-					     bool no_map);
 extern u64 dt_mem_next_cell(int s, const __be32 **cellp);
 
 /* Early flat tree scan hooks */

scripts/Makefile.lib

@@ -309,8 +309,7 @@ DTC_FLAGS += -Wno-unit_address_vs_reg \
 	-Wno-alias_paths \
 	-Wno-graph_child_address \
 	-Wno-simple_bus_reg \
-	-Wno-unique_unit_address \
-	-Wno-pci_device_reg
+	-Wno-unique_unit_address
 endif
 
 ifneq ($(findstring 2,$(KBUILD_EXTRA_WARN)),)