Commit 9eba4b8e authored by Fabio Estevam's avatar Fabio Estevam Committed by Shawn Guo

ARM: mx31moboard-smartbot: Remove camera support

Since commit c93cc614 ("[media] staging/media: remove deprecated
mx3 driver") the mx3 camera driver has been removed, so remove the camera
support from the board file as well.
Signed-off-by: default avatarFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent a20bb25f
...@@ -23,8 +23,6 @@ ...@@ -23,8 +23,6 @@
#include <linux/usb/otg.h> #include <linux/usb/otg.h>
#include <linux/usb/ulpi.h> #include <linux/usb/ulpi.h>
#include <media/soc_camera.h>
#include "board-mx31moboard.h" #include "board-mx31moboard.h"
#include "common.h" #include "common.h"
#include "devices-imx31.h" #include "devices-imx31.h"
...@@ -37,16 +35,6 @@ static unsigned int smartbot_pins[] = { ...@@ -37,16 +35,6 @@ static unsigned int smartbot_pins[] = {
/* UART1 */ /* UART1 */
MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2, MX31_PIN_CTS2__CTS2, MX31_PIN_RTS2__RTS2,
MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2, MX31_PIN_TXD2__TXD2, MX31_PIN_RXD2__RXD2,
/* CSI */
MX31_PIN_CSI_D4__CSI_D4, MX31_PIN_CSI_D5__CSI_D5,
MX31_PIN_CSI_D6__CSI_D6, MX31_PIN_CSI_D7__CSI_D7,
MX31_PIN_CSI_D8__CSI_D8, MX31_PIN_CSI_D9__CSI_D9,
MX31_PIN_CSI_D10__CSI_D10, MX31_PIN_CSI_D11__CSI_D11,
MX31_PIN_CSI_D12__CSI_D12, MX31_PIN_CSI_D13__CSI_D13,
MX31_PIN_CSI_D14__CSI_D14, MX31_PIN_CSI_D15__CSI_D15,
MX31_PIN_CSI_HSYNC__CSI_HSYNC, MX31_PIN_CSI_MCLK__CSI_MCLK,
MX31_PIN_CSI_PIXCLK__CSI_PIXCLK, MX31_PIN_CSI_VSYNC__CSI_VSYNC,
MX31_PIN_GPIO3_0__GPIO3_0, MX31_PIN_GPIO3_1__GPIO3_1,
/* ENABLES */ /* ENABLES */
MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9, MX31_PIN_DTR_DCE1__GPIO2_8, MX31_PIN_DSR_DCE1__GPIO2_9,
MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11, MX31_PIN_RI_DCE1__GPIO2_10, MX31_PIN_DCD_DCE1__GPIO2_11,
...@@ -56,65 +44,6 @@ static const struct imxuart_platform_data uart_pdata __initconst = { ...@@ -56,65 +44,6 @@ static const struct imxuart_platform_data uart_pdata __initconst = {
.flags = IMXUART_HAVE_RTSCTS, .flags = IMXUART_HAVE_RTSCTS,
}; };
#define CAM_POWER IOMUX_TO_GPIO(MX31_PIN_GPIO3_1)
#define CAM_RST_B IOMUX_TO_GPIO(MX31_PIN_GPIO3_0)
static int smartbot_cam_power(struct device *dev, int on)
{
gpio_set_value(CAM_POWER, !on);
return 0;
}
static int smartbot_cam_reset(struct device *dev)
{
gpio_set_value(CAM_RST_B, 0);
udelay(100);
gpio_set_value(CAM_RST_B, 1);
return 0;
}
static struct i2c_board_info smartbot_i2c_devices[] = {
{
I2C_BOARD_INFO("mt9t031", 0x5d),
},
};
static struct soc_camera_link base_iclink = {
.bus_id = 0, /* Must match with the camera ID */
.power = smartbot_cam_power,
.reset = smartbot_cam_reset,
.board_info = &smartbot_i2c_devices[0],
.i2c_adapter_id = 0,
};
static struct platform_device smartbot_camera[] = {
{
.name = "soc-camera-pdrv",
.id = 0,
.dev = {
.platform_data = &base_iclink,
},
},
};
static struct platform_device *smartbot_cameras[] __initdata = {
&smartbot_camera[0],
};
static int __init smartbot_cam_init(void)
{
int ret = gpio_request(CAM_RST_B, "cam-reset");
if (ret)
return ret;
gpio_direction_output(CAM_RST_B, 1);
ret = gpio_request(CAM_POWER, "cam-standby");
if (ret)
return ret;
gpio_direction_output(CAM_POWER, 0);
return 0;
}
static const struct fsl_usb2_platform_data usb_pdata __initconst = { static const struct fsl_usb2_platform_data usb_pdata __initconst = {
.operating_mode = FSL_USB2_DR_DEVICE, .operating_mode = FSL_USB2_DR_DEVICE,
.phy_mode = FSL_USB2_PHY_ULPI, .phy_mode = FSL_USB2_PHY_ULPI,
...@@ -201,7 +130,4 @@ void __init mx31moboard_smartbot_init(int board) ...@@ -201,7 +130,4 @@ void __init mx31moboard_smartbot_init(int board)
} }
smartbot_resets_init(); smartbot_resets_init();
smartbot_cam_init();
platform_add_devices(smartbot_cameras, ARRAY_SIZE(smartbot_cameras));
} }
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment