IB/qib: New SERDES init routine and improvements to SI quality

Implement new SERDES initialization routine and improvements to signal
integrity -- disable LE1 adaptation, disable LOS after link-up, set
better SERDES parameters.
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>

drivers/infiniband/hw/qib/qib_iba7322.c

@@ -71,6 +71,9 @@ static void qib_7322_mini_pcs_reset(struct qib_pportdata *);
 
 static u32 ahb_mod(struct qib_devdata *, int, int, int, u32, u32);
 static void ibsd_wr_allchans(struct qib_pportdata *, int, unsigned, unsigned);
+static void serdes_7322_los_enable(struct qib_pportdata *, int);
+static int serdes_7322_init_old(struct qib_pportdata *);
+static int serdes_7322_init_new(struct qib_pportdata *);
 
 #define BMASK(msb, lsb) (((1 << ((msb) + 1 - (lsb))) - 1) << (lsb))
 
@@ -1692,6 +1695,8 @@ static void handle_serdes_issues(struct qib_pportdata *ppd, u64 ibcst)
 	    (ibcst & SYM_MASK(IBCStatusA_0, LinkSpeedQDR))) {
 		force_h1(ppd);
 		ppd->cpspec->qdr_reforce = 1;
+		if (!ppd->dd->cspec->r1)
+			serdes_7322_los_enable(ppd, 0);
 	} else if (ppd->cpspec->qdr_reforce &&
 		(ibcst & SYM_MASK(IBCStatusA_0, LinkSpeedQDR)) &&
 		 (ibclt == IB_7322_LT_STATE_CFGENH ||
@@ -1707,7 +1712,20 @@ static void handle_serdes_issues(struct qib_pportdata *ppd, u64 ibcst)
 	      ibclt <= IB_7322_LT_STATE_SLEEPQUIET)))
 		adj_tx_serdes(ppd);
 
-	if (!ppd->cpspec->qdr_dfe_on && ibclt != IB_7322_LT_STATE_LINKUP &&
+	if (ibclt != IB_7322_LT_STATE_LINKUP) {
+		u8 ltstate = qib_7322_phys_portstate(ibcst);
+		u8 pibclt = (u8)SYM_FIELD(ppd->lastibcstat, IBCStatusA_0,
+					  LinkTrainingState);
+		if (!ppd->dd->cspec->r1 &&
+		    pibclt == IB_7322_LT_STATE_LINKUP &&
+		    ltstate != IB_PHYSPORTSTATE_LINK_ERR_RECOVER &&
+		    ltstate != IB_PHYSPORTSTATE_RECOVERY_RETRAIN &&
+		    ltstate != IB_PHYSPORTSTATE_RECOVERY_WAITRMT &&
+		    ltstate != IB_PHYSPORTSTATE_RECOVERY_IDLE)
+			/* If the link went down (but no into recovery,
+			 * turn LOS back on */
+			serdes_7322_los_enable(ppd, 1);
+		if (!ppd->cpspec->qdr_dfe_on &&
 		    ibclt <= IB_7322_LT_STATE_SLEEPQUIET) {
 			ppd->cpspec->qdr_dfe_on = 1;
 			ppd->cpspec->qdr_dfe_time = 0;
@@ -1716,6 +1734,10 @@ static void handle_serdes_issues(struct qib_pportdata *ppd, u64 ibcst)
 					    ppd->dd->cspec->r1 ?
 					    QDR_STATIC_ADAPT_DOWN_R1 :
 					    QDR_STATIC_ADAPT_DOWN);
+			printk(KERN_INFO QIB_DRV_NAME
+				" IB%u:%u re-enabled QDR adaptation "
+				"ibclt %x\n", ppd->dd->unit, ppd->port, ibclt);
+		}
 	}
 }
 
@@ -5544,7 +5566,7 @@ static void qsfp_7322_event(struct work_struct *work)
 		u64 now = get_jiffies_64();
 		if (time_after64(now, pwrup))
 			break;
-		msleep(1);
+		msleep(20);
 	}
 	ret = qib_refresh_qsfp_cache(ppd, &qd->cache);
 	/*
@@ -6519,7 +6541,7 @@ static void qib_7322_txchk_change(struct qib_devdata *dd, u32 start,
 		/* make sure we see an updated copy next time around */
 		sendctrl_7322_mod(dd->pport, QIB_SENDCTRL_AVAIL_BLIP);
 		sleeps++;
-		msleep(1);
+		msleep(20);
 	}
 
 	switch (which) {
@@ -7234,9 +7256,30 @@ static void ibsd_wr_allchans(struct qib_pportdata *ppd, int addr, unsigned data,
 	}
 }
 
+static void serdes_7322_los_enable(struct qib_pportdata *ppd, int enable)
+{
+	u64 data = qib_read_kreg_port(ppd, krp_serdesctrl);
+	printk(KERN_INFO QIB_DRV_NAME " Turning LOS %s for port %d\n",
+		 (enable ? "on" : "off"), ppd->port);
+	if (enable)
+		data |= SYM_MASK(IBSerdesCtrl_0, RXLOSEN);
+	else
+		data &= ~SYM_MASK(IBSerdesCtrl_0, RXLOSEN);
+	qib_write_kreg_port(ppd, krp_serdesctrl, data);
+}
+
 static int serdes_7322_init(struct qib_pportdata *ppd)
 {
-	u64 data;
+	int ret = 0;
+	if (ppd->dd->cspec->r1)
+		ret = serdes_7322_init_old(ppd);
+	else
+		ret = serdes_7322_init_new(ppd);
+	return ret;
+}
+
+static int serdes_7322_init_old(struct qib_pportdata *ppd)
+{
 	u32 le_val;
 
 	/*
@@ -7294,9 +7337,7 @@ static int serdes_7322_init(struct qib_pportdata *ppd)
 	ibsd_wr_allchans(ppd, 20, (2 << 10), BMASK(12, 10)); /* DDR */
 	ibsd_wr_allchans(ppd, 20, (4 << 13), BMASK(15, 13)); /* SDR */
 
-	data = qib_read_kreg_port(ppd, krp_serdesctrl);
-	qib_write_kreg_port(ppd, krp_serdesctrl, data |
-		SYM_MASK(IBSerdesCtrl_0, RXLOSEN));
+	serdes_7322_los_enable(ppd, 1);
 
 	/* rxbistena; set 0 to avoid effects of it switch later */
 	ibsd_wr_allchans(ppd, 9, 0 << 15, 1 << 15);
@@ -7336,6 +7377,205 @@ static int serdes_7322_init(struct qib_pportdata *ppd)
 	return 0;
 }
 
+static int serdes_7322_init_new(struct qib_pportdata *ppd)
+{
+	u64 tstart;
+	u32 le_val, rxcaldone;
+	int chan, chan_done = (1 << SERDES_CHANS) - 1;
+
+	/*
+	 * Initialize the Tx DDS tables.  Also done every QSFP event,
+	 * for adapters with QSFP
+	 */
+	init_txdds_table(ppd, 0);
+
+	/* Clear cmode-override, may be set from older driver */
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 10, 0 << 14, 1 << 14);
+
+	/* ensure no tx overrides from earlier driver loads */
+	qib_write_kreg_port(ppd, krp_tx_deemph_override,
+		SYM_MASK(IBSD_TX_DEEMPHASIS_OVERRIDE_0,
+		reset_tx_deemphasis_override));
+
+	/* START OF LSI SUGGESTED SERDES BRINGUP */
+	/* Reset - Calibration Setup */
+	/*       Stop DFE adaptaion */
+	ibsd_wr_allchans(ppd, 1, 0, BMASK(9, 1));
+	/*       Disable LE1 */
+	ibsd_wr_allchans(ppd, 13, 0, BMASK(5, 5));
+	/*       Disable autoadapt for LE1 */
+	ibsd_wr_allchans(ppd, 1, 0, BMASK(15, 15));
+	/*       Disable LE2 */
+	ibsd_wr_allchans(ppd, 13, 0, BMASK(6, 6));
+	/*       Disable VGA */
+	ibsd_wr_allchans(ppd, 5, 0, BMASK(0, 0));
+	/*       Disable AFE Offset Cancel */
+	ibsd_wr_allchans(ppd, 12, 0, BMASK(12, 12));
+	/*       Disable Timing Loop */
+	ibsd_wr_allchans(ppd, 2, 0, BMASK(3, 3));
+	/*       Disable Frequency Loop */
+	ibsd_wr_allchans(ppd, 2, 0, BMASK(4, 4));
+	/*       Disable Baseline Wander Correction */
+	ibsd_wr_allchans(ppd, 13, 0, BMASK(13, 13));
+	/*       Disable RX Calibration */
+	ibsd_wr_allchans(ppd, 4, 0, BMASK(10, 10));
+	/*       Disable RX Offset Calibration */
+	ibsd_wr_allchans(ppd, 12, 0, BMASK(4, 4));
+	/*       Select BB CDR */
+	ibsd_wr_allchans(ppd, 2, (1 << 15), BMASK(15, 15));
+	/*       CDR Step Size */
+	ibsd_wr_allchans(ppd, 5, 0, BMASK(9, 8));
+	/*       Enable phase Calibration */
+	ibsd_wr_allchans(ppd, 12, (1 << 5), BMASK(5, 5));
+	/*       DFE Bandwidth [2:14-12] */
+	ibsd_wr_allchans(ppd, 2, (4 << 12), BMASK(14, 12));
+	/*       DFE Config (4 taps only) */
+	ibsd_wr_allchans(ppd, 16, 0, BMASK(1, 0));
+	/*       Gain Loop Bandwidth */
+	if (!ppd->dd->cspec->r1) {
+		ibsd_wr_allchans(ppd, 12, 1 << 12, BMASK(12, 12));
+		ibsd_wr_allchans(ppd, 12, 2 << 8, BMASK(11, 8));
+	} else {
+		ibsd_wr_allchans(ppd, 19, (3 << 11), BMASK(13, 11));
+	}
+	/*       Baseline Wander Correction Gain [13:4-0] (leave as default) */
+	/*       Baseline Wander Correction Gain [3:7-5] (leave as default) */
+	/*       Data Rate Select [5:7-6] (leave as default) */
+	/*       RX Parralel Word Width [3:10-8] (leave as default) */
+
+	/* RX REST */
+	/*       Single- or Multi-channel reset */
+	/*       RX Analog reset */
+	/*       RX Digital reset */
+	ibsd_wr_allchans(ppd, 0, 0, BMASK(15, 13));
+	msleep(20);
+	/*       RX Analog reset */
+	ibsd_wr_allchans(ppd, 0, (1 << 14), BMASK(14, 14));
+	msleep(20);
+	/*       RX Digital reset */
+	ibsd_wr_allchans(ppd, 0, (1 << 13), BMASK(13, 13));
+	msleep(20);
+
+	/* setup LoS params; these are subsystem, so chan == 5 */
+	/* LoS filter threshold_count on, ch 0-3, set to 8 */
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 5, 8 << 11, BMASK(14, 11));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 7, 8 << 4, BMASK(7, 4));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 8, 8 << 11, BMASK(14, 11));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 10, 8 << 4, BMASK(7, 4));
+
+	/* LoS filter threshold_count off, ch 0-3, set to 4 */
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 6, 4 << 0, BMASK(3, 0));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 7, 4 << 8, BMASK(11, 8));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 9, 4 << 0, BMASK(3, 0));
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 10, 4 << 8, BMASK(11, 8));
+
+	/* LoS filter select enabled */
+	ahb_mod(ppd->dd, IBSD(ppd->hw_pidx), 5, 9, 1 << 15, 1 << 15);
+
+	/* LoS target data:  SDR=4, DDR=2, QDR=1 */
+	ibsd_wr_allchans(ppd, 14, (1 << 3), BMASK(5, 3)); /* QDR */
+	ibsd_wr_allchans(ppd, 20, (2 << 10), BMASK(12, 10)); /* DDR */
+	ibsd_wr_allchans(ppd, 20, (4 << 13), BMASK(15, 13)); /* SDR */
+
+	/* Turn on LOS on initial SERDES init */
+	serdes_7322_los_enable(ppd, 1);
+	/* FLoop LOS gate: PPM filter  enabled */
+	ibsd_wr_allchans(ppd, 38, 0 << 10, 1 << 10);
+
+	/* RX LATCH CALIBRATION */
+	/*       Enable Eyefinder Phase Calibration latch */
+	ibsd_wr_allchans(ppd, 15, 1, BMASK(0, 0));
+	/*       Enable RX Offset Calibration latch */
+	ibsd_wr_allchans(ppd, 12, (1 << 4), BMASK(4, 4));
+	msleep(20);
+	/*       Start Calibration */
+	ibsd_wr_allchans(ppd, 4, (1 << 10), BMASK(10, 10));
+	tstart = get_jiffies_64();
+	while (chan_done &&
+	       !time_after64(tstart, tstart + msecs_to_jiffies(500))) {
+		msleep(20);
+		for (chan = 0; chan < SERDES_CHANS; ++chan) {
+			rxcaldone = ahb_mod(ppd->dd, IBSD(ppd->hw_pidx),
+					    (chan + (chan >> 1)),
+					    25, 0, 0);
+			if ((~rxcaldone & (u32)BMASK(9, 9)) == 0 &&
+			    (~chan_done & (1 << chan)) == 0)
+				chan_done &= ~(1 << chan);
+		}
+	}
+	if (chan_done) {
+		printk(KERN_INFO QIB_DRV_NAME
+			 " Serdes %d calibration not done after .5 sec: 0x%x\n",
+			 IBSD(ppd->hw_pidx), chan_done);
+	} else {
+		for (chan = 0; chan < SERDES_CHANS; ++chan) {
+			rxcaldone = ahb_mod(ppd->dd, IBSD(ppd->hw_pidx),
+					    (chan + (chan >> 1)),
+					    25, 0, 0);
+			if ((~rxcaldone & (u32)BMASK(10, 10)) == 0)
+				printk(KERN_INFO QIB_DRV_NAME
+					 " Serdes %d chan %d calibration "
+					 "failed\n", IBSD(ppd->hw_pidx), chan);
+		}
+	}
+
+	/*       Turn off Calibration */
+	ibsd_wr_allchans(ppd, 4, 0, BMASK(10, 10));
+	msleep(20);
+
+	/* BRING RX UP */
+	/*       Set LE2 value (May be overridden in qsfp_7322_event) */
+	le_val = IS_QME(ppd->dd) ? LE2_QME : LE2_DEFAULT;
+	ibsd_wr_allchans(ppd, 13, (le_val << 7), BMASK(9, 7));
+	/*       Set LE2 Loop bandwidth */
+	ibsd_wr_allchans(ppd, 3, (7 << 5), BMASK(7, 5));
+	/*       Enable LE2 */
+	ibsd_wr_allchans(ppd, 13, (1 << 6), BMASK(6, 6));
+	msleep(20);
+	/*       Enable H0 only */
+	ibsd_wr_allchans(ppd, 1, 1, BMASK(9, 1));
+	/* gain hi stop 32 (22) (6:1) lo stop 7 (10:7) target 22 (13) (15:11) */
+	le_val = (ppd->dd->cspec->r1 || IS_QME(ppd->dd)) ? 0xb6c0 : 0x6bac;
+	ibsd_wr_allchans(ppd, 21, le_val, 0xfffe);
+	/*       Enable VGA */
+	ibsd_wr_allchans(ppd, 5, 0, BMASK(0, 0));
+	msleep(20);
+	/*       Set Frequency Loop Bandwidth */
+	ibsd_wr_allchans(ppd, 2, (7 << 5), BMASK(8, 5));
+	/*       Enable Frequency Loop */
+	ibsd_wr_allchans(ppd, 2, (1 << 4), BMASK(4, 4));
+	/*       Set Timing Loop Bandwidth */
+	ibsd_wr_allchans(ppd, 2, 0, BMASK(11, 9));
+	/*       Enable Timing Loop */
+	ibsd_wr_allchans(ppd, 2, (1 << 3), BMASK(3, 3));
+	msleep(50);
+	/*       Enable DFE
+	 *       Set receive adaptation mode.  SDR and DDR adaptation are
+	 *       always on, and QDR is initially enabled; later disabled.
+	 */
+	qib_write_kreg_port(ppd, krp_static_adapt_dis(0), 0ULL);
+	qib_write_kreg_port(ppd, krp_static_adapt_dis(1), 0ULL);
+	qib_write_kreg_port(ppd, krp_static_adapt_dis(2),
+			    ppd->dd->cspec->r1 ?
+			    QDR_STATIC_ADAPT_DOWN_R1 : QDR_STATIC_ADAPT_DOWN);
+	ppd->cpspec->qdr_dfe_on = 1;
+	/*       Disable LE1  */
+	ibsd_wr_allchans(ppd, 13, (0 << 5), (1 << 5));
+	/*       Disable auto adapt for LE1 */
+	ibsd_wr_allchans(ppd, 1, (0 << 15), BMASK(15, 15));
+	msleep(20);
+	/*       Enable AFE Offset Cancel */
+	ibsd_wr_allchans(ppd, 12, (1 << 12), BMASK(12, 12));
+	/*       Enable Baseline Wander Correction */
+	ibsd_wr_allchans(ppd, 12, (1 << 13), BMASK(13, 13));
+	/* Termination: rxtermctrl_r2d addr 11 bits [12:11] = 1 */
+	ibsd_wr_allchans(ppd, 11, (1 << 11), BMASK(12, 11));
+	/* VGA output common mode */
+	ibsd_wr_allchans(ppd, 12, (3 << 2), BMASK(3, 2));
+
+	return 0;
+}
+
 /* start adjust QMH serdes parameters */
 
 static void set_man_code(struct qib_pportdata *ppd, int chan, int code)