Commit a29aaf55 authored by Moiz Sonasath's avatar Moiz Sonasath Committed by Samuel Ortiz

mfd: Disable TWL4030/5030 I2C1/I2C4 internal pull-ups

This patch disables TWL4030/5030 I2C1 adn I2C4(SR) internal pull-up, to
use only the external HW resistor >=470 Ohm for the assured
functionality in HS mode.

While testing the I2C in High Speed mode, it was discovered that
without a proper pull-up resistor, there is data corruption during
multi-byte transfer. RTC(time_set) test case was used for testing.

From the analysis done, it was concluded that ideally we need a
pull-up of 1.6k Ohm(recomended) or atleast 470 Ohm or greater for
assured performance in HS mode.
Signed-off-by: default avatarMoiz Sonasath <m-sonasath@ti.com>
Signed-off-by: default avatarAllen Pais <allen.pais@ti.com>
Signed-off-by: default avatarSamuel Ortiz <sameo@linux.intel.com>
parent e82c60ae
......@@ -958,6 +958,7 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id)
int status;
unsigned i;
struct twl4030_platform_data *pdata = client->dev.platform_data;
u8 temp;
if (!pdata) {
dev_dbg(&client->dev, "no platform data?\n");
......@@ -1025,6 +1026,18 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id)
goto fail;
}
/* Disable TWL4030/TWL5030 I2C Pull-up on I2C1 and I2C4(SR) interface.
* Program I2C_SCL_CTRL_PU(bit 0)=0, I2C_SDA_CTRL_PU (bit 2)=0,
* SR_I2C_SCL_CTRL_PU(bit 4)=0 and SR_I2C_SDA_CTRL_PU(bit 6)=0.
*/
if (twl_class_is_4030()) {
twl_i2c_read_u8(TWL4030_MODULE_INTBR, &temp, REG_GPPUPDCTR1);
temp &= ~(SR_I2C_SDA_CTRL_PU | SR_I2C_SCL_CTRL_PU | \
I2C_SDA_CTRL_PU | I2C_SCL_CTRL_PU);
twl_i2c_write_u8(TWL4030_MODULE_INTBR, temp, REG_GPPUPDCTR1);
}
status = add_children(pdata, id->driver_data);
fail:
if (status < 0)
......
......@@ -239,6 +239,21 @@ int twl6030_interrupt_mask(u8 bit_mask, u8 offset);
/*----------------------------------------------------------------------*/
/*Interface Bit Register (INTBR) offsets
*(Use TWL_4030_MODULE_INTBR)
*/
#define REG_GPPUPDCTR1 0x0F
/*I2C1 and I2C4(SR) SDA/SCL pull-up control bits */
#define I2C_SCL_CTRL_PU BIT(0)
#define I2C_SDA_CTRL_PU BIT(2)
#define SR_I2C_SCL_CTRL_PU BIT(4)
#define SR_I2C_SDA_CTRL_PU BIT(6)
/*----------------------------------------------------------------------*/
/*
* Keypad register offsets (use TWL4030_MODULE_KEYPAD)
* ... SIH/interrupt only
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment