enic: Move the Cisco driver

Move the Cisco driver into drivers/net/ethernet/cisco/ and make the
necessary Kconfig and Makefile changes.

CC: Christian Benvenuti <benve@cisco.com>
CC: Vasanthy Kolluri <vkolluri@cisco.com>
CC: Roopa Prabhu <roprabhu@cisco.com>
CC: David Wang <dwang2@cisco.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

MAINTAINERS

@@ -1761,7 +1761,7 @@ M:	Vasanthy Kolluri <vkolluri@cisco.com>
 M:	Roopa Prabhu <roprabhu@cisco.com>
 M:	David Wang <dwang2@cisco.com>
 S:	Supported
-F:	drivers/net/enic/
+F:	drivers/net/ethernet/cisco/enic/
 
 CIRRUS LOGIC EP93XX ETHERNET DRIVER
 M:	Hartley Sweeten <hsweeten@visionengravers.com>

drivers/net/Kconfig

@@ -1457,12 +1457,6 @@ if NETDEV_10000
 config MDIO
 	tristate
 
-config ENIC
-	tristate "Cisco VIC Ethernet NIC Support"
-	depends on PCI && INET
-	help
-	  This enables the support for the Cisco VIC Ethernet card.
-
 config PASEMI_MAC
 	tristate "PA Semi 1/10Gbit MAC"
 	depends on PPC_PASEMI && PCI && INET

drivers/net/Makefile

@@ -20,7 +20,6 @@ obj-$(CONFIG_ATL1C) += atl1c/
 obj-$(CONFIG_GIANFAR) += gianfar_driver.o
 obj-$(CONFIG_PTP_1588_CLOCK_GIANFAR) += gianfar_ptp.o
 obj-$(CONFIG_TEHUTI) += tehuti.o
-obj-$(CONFIG_ENIC) += enic/
 obj-$(CONFIG_JME) += jme.o
 obj-$(CONFIG_VMXNET3) += vmxnet3/
 

drivers/net/ethernet/Kconfig

@@ -17,6 +17,7 @@ source "drivers/net/ethernet/amd/Kconfig"
 source "drivers/net/ethernet/broadcom/Kconfig"
 source "drivers/net/ethernet/brocade/Kconfig"
 source "drivers/net/ethernet/chelsio/Kconfig"
+source "drivers/net/ethernet/cisco/Kconfig"
 source "drivers/net/ethernet/emulex/Kconfig"
 source "drivers/net/ethernet/neterion/Kconfig"
 source "drivers/net/ethernet/ibm/Kconfig"

drivers/net/ethernet/Makefile

@@ -8,6 +8,7 @@ obj-$(CONFIG_NET_VENDOR_AMD) += amd/
 obj-$(CONFIG_NET_VENDOR_BROADCOM) += broadcom/
 obj-$(CONFIG_NET_VENDOR_BROCADE) += brocade/
 obj-$(CONFIG_NET_VENDOR_CHELSIO) += chelsio/
+obj-$(CONFIG_NET_VENDOR_CISCO) += cisco/
 obj-$(CONFIG_NET_VENDOR_EMULEX) += emulex/
 obj-$(CONFIG_NET_VENDOR_EXAR) += neterion/
 obj-$(CONFIG_NET_VENDOR_IBM) += ibm/

drivers/net/ethernet/cisco/Kconfig

+#
+# Cisco device configuration
+#
+
+config NET_VENDOR_CISCO
+	bool "Cisco devices"
+	depends on PCI && INET
+	---help---
+	  If you have a network (Ethernet) card belonging to this class, say Y
+	  and read the Ethernet-HOWTO, available from
+	  <http://www.tldp.org/docs.html#howto>.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Cisco cards. If you say Y, you will be asked for
+	  your specific card in the following questions.
+
+if NET_VENDOR_CISCO
+
+source "drivers/net/ethernet/cisco/enic/Kconfig"
+
+endif # NET_VENDOR_CISCO

drivers/net/ethernet/cisco/Makefile

+#
+# Makefile for the Cisco device drivers.
+#
+
+obj-$(CONFIG_ENIC) += enic/

drivers/net/ethernet/cisco/enic/Kconfig

+#
+# Cisco device configuration
+#
+
+config ENIC
+	tristate "Cisco VIC Ethernet NIC Support"
+	depends on PCI && INET
+	---help---
+	  This enables the support for the Cisco VIC Ethernet card.