Input: add support for ChipOne icn8318 based touchscreens

The ChipOne icn8318 is an i2c capacitive touchscreen controller typically
used in cheap android tablets, this commit adds a driver for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>

Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt

+* ChipOne icn8318 I2C touchscreen controller
+
+Required properties:
+ - compatible		  : "chipone,icn8318"
+ - reg			  : I2C slave address of the chip (0x40)
+ - interrupt-parent	  : a phandle pointing to the interrupt controller
+			    serving the interrupt for this chip
+ - interrupts		  : interrupt specification for the icn8318 interrupt
+ - wake-gpios		  : GPIO specification for the WAKE input
+ - touchscreen-size-x	  : horizontal resolution of touchscreen (in pixels)
+ - touchscreen-size-y	  : vertical resolution of touchscreen (in pixels)
+
+Optional properties:
+ - pinctrl-names	  : should be "default"
+ - pinctrl-0:		  : a phandle pointing to the pin settings for the
+			    control gpios
+ - touchscreen-fuzz-x	  : horizontal noise value of the absolute input
+			    device (in pixels)
+ - touchscreen-fuzz-y	  : vertical noise value of the absolute input
+			    device (in pixels)
+ - touchscreen-inverted-x : X axis is inverted (boolean)
+ - touchscreen-inverted-y : Y axis is inverted (boolean)
+ - touchscreen-swapped-x-y	  : X and Y axis are swapped (boolean)
+			    Swapping is done after inverting the axis
+
+Example:
+
+i2c@00000000 {
+	/* ... */
+
+	chipone_icn8318@40 {
+		compatible = "chipone,icn8318";
+		reg = <0x40>;
+		interrupt-parent = <&pio>;
+		interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* EINT9 (PG9) */
+		pinctrl-names = "default";
+		pinctrl-0 = <&ts_wake_pin_p66>;
+		wake-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
+		touchscreen-size-x = <800>;
+		touchscreen-size-y = <480>;
+		touchscreen-inverted-x;
+		touchscreen-swapped-x-y;
+	};
+
+	/* ... */
+};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -37,6 +37,7 @@ capella	Capella Microsystems, Inc
 cavium	Cavium, Inc.
 cdns	Cadence Design Systems Inc.
 chipidea	Chipidea, Inc
+chipone		ChipOne
 chipspark	ChipSPARK
 chrp	Common Hardware Reference Platform
 chunghwa	Chunghwa Picture Tubes Ltd.

MAINTAINERS

@@ -2523,6 +2523,13 @@ L:	linux-usb@vger.kernel.org
 S:	Maintained
 F:	drivers/usb/chipidea/
 
+CHIPONE ICN8318 I2C TOUCHSCREEN DRIVER
+M:	Hans de Goede <hdegoede@redhat.com>
+L:	linux-input@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/input/touchscreen/chipone_icn8318.txt
+F:	drivers/input/touchscreen/chipone_icn8318.c
+
 CHROME HARDWARE PLATFORM SUPPORT
 M:	Olof Johansson <olof@lixom.net>
 S:	Maintained

drivers/input/touchscreen/Kconfig

@@ -140,6 +140,19 @@ config TOUCHSCREEN_BU21013
 	  To compile this driver as a module, choose M here: the
 	  module will be called bu21013_ts.
 
+config TOUCHSCREEN_CHIPONE_ICN8318
+	tristate "chipone icn8318 touchscreen controller"
+	depends on GPIOLIB
+	depends on I2C
+	depends on OF
+	help
+	  Say Y here if you have a ChipOne icn8318 based I2C touchscreen.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called chipone_icn8318.
+
 config TOUCHSCREEN_CY8CTMG110
 	tristate "cy8ctmg110 touchscreen"
 	depends on I2C

drivers/input/touchscreen/Makefile

@@ -17,6 +17,7 @@ obj-$(CONFIG_TOUCHSCREEN_AR1021_I2C)	+= ar1021_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ATMEL_MXT)	+= atmel_mxt_ts.o
 obj-$(CONFIG_TOUCHSCREEN_AUO_PIXCIR)	+= auo-pixcir-ts.o
 obj-$(CONFIG_TOUCHSCREEN_BU21013)	+= bu21013_ts.o
+obj-$(CONFIG_TOUCHSCREEN_CHIPONE_ICN8318)	+= chipone_icn8318.o
 obj-$(CONFIG_TOUCHSCREEN_CY8CTMG110)	+= cy8ctmg110_ts.o
 obj-$(CONFIG_TOUCHSCREEN_CYTTSP_CORE)	+= cyttsp_core.o
 obj-$(CONFIG_TOUCHSCREEN_CYTTSP_I2C)	+= cyttsp_i2c.o cyttsp_i2c_common.o

drivers/input/touchscreen/chipone_icn8318.c

+/*
+ * Driver for ChipOne icn8318 i2c touchscreen controller
+ *
+ * Copyright (c) 2015 Red Hat Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * Red Hat authors:
+ * Hans de Goede <hdegoede@redhat.com>
+ */
+
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/i2c.h>
+#include <linux/input.h>
+#include <linux/input/mt.h>
+#include <linux/module.h>
+#include <linux/of.h>
+
+#define ICN8318_REG_POWER		4
+#define ICN8318_REG_TOUCHDATA		16
+
+#define ICN8318_POWER_ACTIVE		0
+#define ICN8318_POWER_MONITOR		1
+#define ICN8318_POWER_HIBERNATE		2
+
+#define ICN8318_MAX_TOUCHES		5
+
+struct icn8318_touch {
+	__u8 slot;
+	__be16 x;
+	__be16 y;
+	__u8 pressure;	/* Seems more like finger width then pressure really */
+	__u8 event;
+/* The difference between 2 and 3 is unclear */
+#define ICN8318_EVENT_NO_DATA	1 /* No finger seen yet since wakeup */
+#define ICN8318_EVENT_UPDATE1	2 /* New or updated coordinates */
+#define ICN8318_EVENT_UPDATE2	3 /* New or updated coordinates */
+#define ICN8318_EVENT_END	4 /* Finger lifted */
+} __packed;
+
+struct icn8318_touch_data {
+	__u8 softbutton;
+	__u8 touch_count;
+	struct icn8318_touch touches[ICN8318_MAX_TOUCHES];
+} __packed;
+
+struct icn8318_data {
+	struct i2c_client *client;
+	struct input_dev *input;
+	struct gpio_desc *wake_gpio;
+	u32 max_x;
+	u32 max_y;
+	bool invert_x;
+	bool invert_y;
+	bool swap_x_y;
+};
+
+static int icn8318_read_touch_data(struct i2c_client *client,
+				   struct icn8318_touch_data *touch_data)
+{
+	u8 reg = ICN8318_REG_TOUCHDATA;
+	struct i2c_msg msg[2] = {
+		{
+			.addr = client->addr,
+			.len = 1,
+			.buf = &reg
+		},
+		{
+			.addr = client->addr,
+			.flags = I2C_M_RD,
+			.len = sizeof(struct icn8318_touch_data),
+			.buf = (u8 *)touch_data
+		}
+	};
+
+	return i2c_transfer(client->adapter, msg, 2);
+}
+
+static inline bool icn8318_touch_active(u8 event)
+{
+	return (event == ICN8318_EVENT_UPDATE1) ||
+	       (event == ICN8318_EVENT_UPDATE2);
+}
+
+static irqreturn_t icn8318_irq(int irq, void *dev_id)
+{
+	struct icn8318_data *data = dev_id;
+	struct device *dev = &data->client->dev;
+	struct icn8318_touch_data touch_data;
+	int i, ret, x, y;
+
+	ret = icn8318_read_touch_data(data->client, &touch_data);
+	if (ret < 0) {
+		dev_err(dev, "Error reading touch data: %d\n", ret);
+		return IRQ_HANDLED;
+	}
+
+	if (touch_data.softbutton) {
+		/*
+		 * Other data is invalid when a softbutton is pressed.
+		 * This needs some extra devicetree bindings to map the icn8318
+		 * softbutton codes to evdev codes. Currently no known devices
+		 * use this.
+		 */
+		return IRQ_HANDLED;
+	}
+
+	if (touch_data.touch_count > ICN8318_MAX_TOUCHES) {
+		dev_warn(dev, "Too much touches %d > %d\n",
+			 touch_data.touch_count, ICN8318_MAX_TOUCHES);
+		touch_data.touch_count = ICN8318_MAX_TOUCHES;
+	}
+
+	for (i = 0; i < touch_data.touch_count; i++) {
+		struct icn8318_touch *touch = &touch_data.touches[i];
+		bool act = icn8318_touch_active(touch->event);
+
+		input_mt_slot(data->input, touch->slot);
+		input_mt_report_slot_state(data->input, MT_TOOL_FINGER, act);
+		if (!act)
+			continue;
+
+		x = be16_to_cpu(touch->x);
+		y = be16_to_cpu(touch->y);
+
+		if (data->invert_x)
+			x = data->max_x - x;
+
+		if (data->invert_y)
+			y = data->max_y - y;
+
+		if (!data->swap_x_y) {
+			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, x);
+			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, y);
+		} else {
+			input_event(data->input, EV_ABS, ABS_MT_POSITION_X, y);
+			input_event(data->input, EV_ABS, ABS_MT_POSITION_Y, x);
+		}
+	}
+
+	input_mt_sync_frame(data->input);
+	input_sync(data->input);
+
+	return IRQ_HANDLED;
+}
+
+static int icn8318_start(struct input_dev *dev)
+{
+	struct icn8318_data *data = input_get_drvdata(dev);
+
+	enable_irq(data->client->irq);
+	gpiod_set_value_cansleep(data->wake_gpio, 1);
+
+	return 0;
+}
+
+static void icn8318_stop(struct input_dev *dev)
+{
+	struct icn8318_data *data = input_get_drvdata(dev);
+
+	disable_irq(data->client->irq);
+	i2c_smbus_write_byte_data(data->client, ICN8318_REG_POWER,
+				  ICN8318_POWER_HIBERNATE);
+	gpiod_set_value_cansleep(data->wake_gpio, 0);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int icn8318_suspend(struct device *dev)
+{
+	struct icn8318_data *data = i2c_get_clientdata(to_i2c_client(dev));
+
+	mutex_lock(&data->input->mutex);
+	if (data->input->users)
+		icn8318_stop(data->input);
+	mutex_unlock(&data->input->mutex);
+
+	return 0;
+}
+
+static int icn8318_resume(struct device *dev)
+{
+	struct icn8318_data *data = i2c_get_clientdata(to_i2c_client(dev));
+
+	mutex_lock(&data->input->mutex);
+	if (data->input->users)
+		icn8318_start(data->input);
+	mutex_unlock(&data->input->mutex);
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(icn8318_pm_ops, icn8318_suspend, icn8318_resume);
+
+static int icn8318_probe(struct i2c_client *client,
+			 const struct i2c_device_id *id)
+{
+	struct device *dev = &client->dev;
+	struct device_node *np = dev->of_node;
+	struct icn8318_data *data;
+	struct input_dev *input;
+	u32 fuzz_x = 0, fuzz_y = 0;
+	int error;
+
+	if (!client->irq) {
+		dev_err(dev, "Error no irq specified\n");
+		return -EINVAL;
+	}
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->wake_gpio = devm_gpiod_get(dev, "wake", GPIOD_OUT_LOW);
+	if (IS_ERR(data->wake_gpio)) {
+		error = PTR_ERR(data->wake_gpio);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Error getting wake gpio: %d\n", error);
+		return error;
+	}
+
+	if (of_property_read_u32(np, "touchscreen-size-x", &data->max_x) ||
+	    of_property_read_u32(np, "touchscreen-size-y", &data->max_y)) {
+		dev_err(dev, "Error touchscreen-size-x and/or -y missing\n");
+		return -EINVAL;
+	}
+
+	/* Optional */
+	of_property_read_u32(np, "touchscreen-fuzz-x", &fuzz_x);
+	of_property_read_u32(np, "touchscreen-fuzz-y", &fuzz_y);
+	data->invert_x = of_property_read_bool(np, "touchscreen-inverted-x");
+	data->invert_y = of_property_read_bool(np, "touchscreen-inverted-y");
+	data->swap_x_y = of_property_read_bool(np, "touchscreen-swapped-x-y");
+
+	input = devm_input_allocate_device(dev);
+	if (!input)
+		return -ENOMEM;
+
+	input->name = client->name;
+	input->id.bustype = BUS_I2C;
+	input->open = icn8318_start;
+	input->close = icn8318_stop;
+	input->dev.parent = dev;
+
+	if (!data->swap_x_y) {
+		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+				     data->max_x, fuzz_x, 0);
+		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+				     data->max_y, fuzz_y, 0);
+	} else {
+		input_set_abs_params(input, ABS_MT_POSITION_X, 0,
+				     data->max_y, fuzz_y, 0);
+		input_set_abs_params(input, ABS_MT_POSITION_Y, 0,
+				     data->max_x, fuzz_x, 0);
+	}
+
+	error = input_mt_init_slots(input, ICN8318_MAX_TOUCHES,
+				    INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
+	if (error)
+		return error;
+
+	data->client = client;
+	data->input = input;
+	input_set_drvdata(input, data);
+
+	error = devm_request_threaded_irq(dev, client->irq, NULL, icn8318_irq,
+					  IRQF_ONESHOT, client->name, data);
+	if (error) {
+		dev_err(dev, "Error requesting irq: %d\n", error);
+		return error;
+	}
+
+	/* Stop device till opened */
+	icn8318_stop(data->input);
+
+	error = input_register_device(input);
+	if (error)
+		return error;
+
+	i2c_set_clientdata(client, data);
+
+	return 0;
+}
+
+static const struct of_device_id icn8318_of_match[] = {
+	{ .compatible = "chipone,icn8318" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, icn8318_of_match);
+
+/* This is useless for OF-enabled devices, but it is needed by I2C subsystem */
+static const struct i2c_device_id icn8318_i2c_id[] = {
+	{ },
+};
+MODULE_DEVICE_TABLE(i2c, icn8318_i2c_id);
+
+static struct i2c_driver icn8318_driver = {
+	.driver = {
+		.owner	= THIS_MODULE,
+		.name	= "chipone_icn8318",
+		.pm	= &icn8318_pm_ops,
+		.of_match_table = icn8318_of_match,
+	},
+	.probe = icn8318_probe,
+	.id_table = icn8318_i2c_id,
+};
+
+module_i2c_driver(icn8318_driver);
+
+MODULE_DESCRIPTION("ChipOne icn8318 I2C Touchscreen Driver");
+MODULE_AUTHOR("Hans de Goede <hdegoede@redhat.com>");
+MODULE_LICENSE("GPL");