Skip to content

L
linux
Commit a9465b58 authored by Olof Johansson's avatar Olof Johansson
Browse files
Options

Merge tag 'sunxi-dt-h3-for-4.12' of... 

Merge tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into next/dt

Allwinner H3 DT changes for 4.12

H3 patches for 4.12, which are mostly related to reworking the H3 DTSI to
be usable on the arm64 H5 DTSI, that shares almost everything with the H3
but the CPU cores.

We also have some new device addition (USB, mostly) that would conflict
otherwise.

* tag 'sunxi-dt-h3-for-4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
  ARM: sun8i: h2+: enable USB OTG for Orange Pi Zero board
  ARM: sun8i: h3: enable USB OTG on Orange Pi One
  ARM: sunxi: h3/h5: add usb_otg and OHCI/EHCI for usbc0 on H3/H5
  arm: sun8i: h3: split Allwinner H3 .dtsi
  arm: sun8i: h3: correct the GIC compatible in H3 to gic-400
  arm: sun8i: h3: drop pinctrl-a10.h inclusion for H3 DTSI
  arm: sun8i: h3: drop skeleton.dtsi inclusion in H3 DTSI
Signed-off-by: default avatarOlof Johansson <olof@lixom.net>
parents ec4c22e7 72897fa3
Show whitespace changes
Inline Side-by-side
Showing with 698 additions and 564 deletions
arch/arm/boot/dts/sun8i-h2-plus-orangepi-zero.dts
View file @ a9465b58
...@@ -95,6 +95,10 @@ wifi_pwrseq: wifi_pwrseq { ...@@ -95,6 +95,10 @@ wifi_pwrseq: wifi_pwrseq {
}; };
}; };
&ehci0 {
status = "okay";
};
&ehci1 { &ehci1 {
status = "okay"; status = "okay";
}; };
...@@ -131,6 +135,10 @@ &mmc1_pins_a { ...@@ -131,6 +135,10 @@ &mmc1_pins_a {
bias-pull-up; bias-pull-up;
}; };
&ohci0 {
status = "okay";
};
&ohci1 { &ohci1 {
status = "okay"; status = "okay";
}; };
...@@ -153,7 +161,17 @@ &uart2 { ...@@ -153,7 +161,17 @@ &uart2 {
status = "disabled"; status = "disabled";
}; };
&usb_otg {
dr_mode = "peripheral";
status = "okay";
};
&usbphy { &usbphy {
/* USB VBUS is always on */ /*
* USB Type-A port VBUS is always on. However, MicroUSB VBUS can only
* power up the board; when it's used as OTG port, this VBUS is
* always off even if the board is powered via GPIO pins.
*/
status = "okay"; status = "okay";
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
}; };
arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
View file @ a9465b58
...@@ -89,6 +89,10 @@ sw4 { ...@@ -89,6 +89,10 @@ sw4 {
}; };
}; };
&ehci0 {
status = "okay";
};
&ehci1 { &ehci1 {
status = "okay"; status = "okay";
}; };
...@@ -103,6 +107,10 @@ &mmc0 { ...@@ -103,6 +107,10 @@ &mmc0 {
status = "okay"; status = "okay";
}; };
&ohci0 {
status = "okay";
};
&ohci1 { &ohci1 {
status = "okay"; status = "okay";
}; };
...@@ -126,6 +134,11 @@ sw_r_opc: key_pins@0 { ...@@ -126,6 +134,11 @@ sw_r_opc: key_pins@0 {
}; };
}; };
&reg_usb0_vbus {
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */
status = "okay";
};
&uart0 { &uart0 {
pinctrl-names = "default"; pinctrl-names = "default";
pinctrl-0 = <&uart0_pins_a>; pinctrl-0 = <&uart0_pins_a>;
...@@ -150,7 +163,14 @@ &uart3 { ...@@ -150,7 +163,14 @@ &uart3 {
status = "disabled"; status = "disabled";
}; };
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usbphy { &usbphy {
/* USB VBUS is always on */ /* USB Type-A port's VBUS is always on */
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
usb0_vbus-supply = <&reg_usb0_vbus>;
status = "okay"; status = "okay";
}; };
arch/arm/boot/dts/sun8i-h3.dtsi
View file @ a9465b58
...@@ -40,16 +40,9 @@ ...@@ -40,16 +40,9 @@
* OTHER DEALINGS IN THE SOFTWARE. * OTHER DEALINGS IN THE SOFTWARE.
*/ */
#include "skeleton.dtsi" #include "sunxi-h3-h5.dtsi"
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ { / {
interrupt-parent = <&gic>;
cpus { cpus {
#address-cells = <1>; #address-cells = <1>;
#size-cells = <0>; #size-cells = <0>;
...@@ -86,72 +79,14 @@ timer { ...@@ -86,72 +79,14 @@ timer {
<GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
}; };
};
clocks { &ccu {
#address-cells = <1>; compatible = "allwinner,sun8i-h3-ccu";
#size-cells = <1>; };
ranges;
osc24M: osc24M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
osc32k: osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
apb0: apb0_clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
clock-mult = <1>;
clocks = <&osc24M>;
clock-output-names = "apb0";
};
apb0_gates: clk@01f01428 {
compatible = "allwinner,sun8i-h3-apb0-gates-clk",
"allwinner,sun4i-a10-gates-clk";
reg = <0x01f01428 0x4>;
#clock-cells = <1>;
clocks = <&apb0>;
clock-indices = <0>, <1>;
clock-output-names = "apb0_pio", "apb0_ir";
};
ir_clk: ir_clk@01f01454 {
compatible = "allwinner,sun4i-a10-mod0-clk";
reg = <0x01f01454 0x4>;
#clock-cells = <0>;
clocks = <&osc32k>, <&osc24M>;
clock-output-names = "ir";
};
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dma: dma-controller@01c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_DMA>;
resets = <&ccu RST_BUS_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 { &mmc0 {
compatible = "allwinner,sun7i-a20-mmc"; compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>, clocks = <&ccu CLK_BUS_MMC0>,
<&ccu CLK_MMC0>, <&ccu CLK_MMC0>,
<&ccu CLK_MMC0_OUTPUT>, <&ccu CLK_MMC0_OUTPUT>,
...@@ -160,17 +95,10 @@ mmc0: mmc@01c0f000 { ...@@ -160,17 +95,10 @@ mmc0: mmc@01c0f000 {
"mmc", "mmc",
"output", "output",
"sample"; "sample";
resets = <&ccu RST_BUS_MMC0>; };
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc1: mmc@01c10000 { &mmc1 {
compatible = "allwinner,sun7i-a20-mmc"; compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>, clocks = <&ccu CLK_BUS_MMC1>,
<&ccu CLK_MMC1>, <&ccu CLK_MMC1>,
<&ccu CLK_MMC1_OUTPUT>, <&ccu CLK_MMC1_OUTPUT>,
...@@ -179,17 +107,10 @@ mmc1: mmc@01c10000 { ...@@ -179,17 +107,10 @@ mmc1: mmc@01c10000 {
"mmc", "mmc",
"output", "output",
"sample"; "sample";
resets = <&ccu RST_BUS_MMC1>; };
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc2: mmc@01c11000 { &mmc2 {
compatible = "allwinner,sun7i-a20-mmc"; compatible = "allwinner,sun7i-a20-mmc";
reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>, clocks = <&ccu CLK_BUS_MMC2>,
<&ccu CLK_MMC2>, <&ccu CLK_MMC2>,
<&ccu CLK_MMC2_OUTPUT>, <&ccu CLK_MMC2_OUTPUT>,
...@@ -198,451 +119,8 @@ mmc2: mmc@01c11000 { ...@@ -198,451 +119,8 @@ mmc2: mmc@01c11000 {
"mmc", "mmc",
"output", "output",
"sample"; "sample";
resets = <&ccu RST_BUS_MMC2>; };
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
usbphy: phy@01c19400 {
compatible = "allwinner,sun8i-h3-usb-phy";
reg = <0x01c19400 0x2c>,
<0x01c1a800 0x4>,
<0x01c1b800 0x4>,
<0x01c1c800 0x4>,
<0x01c1d800 0x4>;
reg-names = "phy_ctrl",
"pmu0",
"pmu1",
"pmu2",
"pmu3";
clocks = <&ccu CLK_USB_PHY0>,
<&ccu CLK_USB_PHY1>,
<&ccu CLK_USB_PHY2>,
<&ccu CLK_USB_PHY3>;
clock-names = "usb0_phy",
"usb1_phy",
"usb2_phy",
"usb3_phy";
resets = <&ccu RST_USB_PHY0>,
<&ccu RST_USB_PHY1>,
<&ccu RST_USB_PHY2>,
<&ccu RST_USB_PHY3>;
reset-names = "usb0_reset",
"usb1_reset",
"usb2_reset",
"usb3_reset";
status = "disabled";
#phy-cells = <1>;
};
ehci1: usb@01c1b000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
ohci1: usb@01c1b400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
<&ccu CLK_USB_OHCI1>;
resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
ehci2: usb@01c1c000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
ohci2: usb@01c1c400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
<&ccu CLK_USB_OHCI2>;
resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
ehci3: usb@01c1d000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1d000 0x100>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
ohci3: usb@01c1d400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1d400 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
<&ccu CLK_USB_OHCI3>;
resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
ccu: clock@01c20000 {
compatible = "allwinner,sun8i-h3-ccu";
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
pio: pinctrl@01c20800 { &pio {
compatible = "allwinner,sun8i-h3-pinctrl"; compatible = "allwinner,sun8i-h3-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
i2c0_pins: i2c0 {
pins = "PA11", "PA12";
function = "i2c0";
};
i2c1_pins: i2c1 {
pins = "PA18", "PA19";
function = "i2c1";
};
i2c2_pins: i2c2 {
pins = "PE12", "PE13";
function = "i2c2";
};
mmc0_pins_a: mmc0@0 {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin: mmc0_cd_pin@0 {
pins = "PF6";
function = "gpio_in";
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
pins = "PG0", "PG1", "PG2", "PG3",
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
spdif_tx_pins_a: spdif@0 {
pins = "PA17";
function = "spdif";
};
spi0_pins: spi0 {
pins = "PC0", "PC1", "PC2", "PC3";
function = "spi0";
};
spi1_pins: spi1 {
pins = "PA15", "PA16", "PA14", "PA13";
function = "spi1";
};
uart0_pins_a: uart0@0 {
pins = "PA4", "PA5";
function = "uart0";
};
uart1_pins: uart1 {
pins = "PG6", "PG7";
function = "uart1";
};
uart1_rts_cts_pins: uart1_rts_cts {
pins = "PG8", "PG9";
function = "uart1";
};
uart2_pins: uart2 {
pins = "PA0", "PA1";
function = "uart2";
};
uart3_pins: uart3 {
pins = "PA13", "PA14";
function = "uart3";
};
};
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
spi0: spi@01c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma 23>, <&dma 23>;
dma-names = "rx", "tx";
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins>;
resets = <&ccu RST_BUS_SPI0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
spi1: spi@01c69000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c69000 0x1000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma 24>, <&dma 24>;
dma-names = "rx", "tx";
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
resets = <&ccu RST_BUS_SPI1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
wdt0: watchdog@01c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
spdif: spdif@01c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-spdif";
reg = <0x01c21000 0x400>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
resets = <&ccu RST_BUS_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma 2>;
dma-names = "tx";
status = "disabled";
};
pwm: pwm@01c21400 {
compatible = "allwinner,sun8i-h3-pwm";
reg = <0x01c21400 0x8>;
clocks = <&osc24M>;
#pwm-cells = <3>;
status = "disabled";
};
codec: codec@01c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-codec";
reg = <0x01c22c00 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
clock-names = "apb", "codec";
resets = <&ccu RST_BUS_CODEC>;
dmas = <&dma 15>, <&dma 15>;
dma-names = "rx", "tx";
allwinner,codec-analog-controls = <&codec_analog>;
status = "disabled";
};
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART0>;
resets = <&ccu RST_BUS_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
};
uart1: serial@01c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART1>;
resets = <&ccu RST_BUS_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
};
uart2: serial@01c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART2>;
resets = <&ccu RST_BUS_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
};
uart3: serial@01c28c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28c00 0x400>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART3>;
resets = <&ccu RST_BUS_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
};
i2c0: i2c@01c2ac00 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C0>;
resets = <&ccu RST_BUS_I2C0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c1: i2c@01c2b000 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C1>;
resets = <&ccu RST_BUS_I2C1>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c2: i2c@01c2b400 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C2>;
resets = <&ccu RST_BUS_I2C2>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
<0x01c86000 0x2000>;
interrupt-controller;
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
rtc: rtc@01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
apb0_reset: reset@01f014b0 {
reg = <0x01f014b0 0x4>;
compatible = "allwinner,sun6i-a31-clock-reset";
#reset-cells = <1>;
};
codec_analog: codec-analog@01f015c0 {
compatible = "allwinner,sun8i-h3-codec-analog";
reg = <0x01f015c0 0x4>;
};
ir: ir@01f02000 {
compatible = "allwinner,sun5i-a13-ir";
clocks = <&apb0_gates 1>, <&ir_clk>;
clock-names = "apb", "ir";
resets = <&apb0_reset 1>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01f02000 0x40>;
status = "disabled";
};
r_pio: pinctrl@01f02c00 {
compatible = "allwinner,sun8i-h3-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_reset 0>;
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
ir_pins_a: ir@0 {
pins = "PL11";
function = "s_cir_rx";
};
};
};
}; };
arch/arm/boot/dts/sunxi-h3-h5.dtsi 0 → 100644
View file @ a9465b58
/*
* Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include <dt-bindings/clock/sun8i-h3-ccu.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
/ {
interrupt-parent = <&gic>;
#address-cells = <1>;
#size-cells = <1>;
clocks {
#address-cells = <1>;
#size-cells = <1>;
ranges;
osc24M: osc24M_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
osc32k: osc32k_clk {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
apb0: apb0_clk {
compatible = "fixed-factor-clock";
#clock-cells = <0>;
clock-div = <1>;
clock-mult = <1>;
clocks = <&osc24M>;
clock-output-names = "apb0";
};
apb0_gates: clk@01f01428 {
compatible = "allwinner,sun8i-h3-apb0-gates-clk",
"allwinner,sun4i-a10-gates-clk";
reg = <0x01f01428 0x4>;
#clock-cells = <1>;
clocks = <&apb0>;
clock-indices = <0>, <1>;
clock-output-names = "apb0_pio", "apb0_ir";
};
ir_clk: ir_clk@01f01454 {
compatible = "allwinner,sun4i-a10-mod0-clk";
reg = <0x01f01454 0x4>;
#clock-cells = <0>;
clocks = <&osc32k>, <&osc24M>;
clock-output-names = "ir";
};
};
soc {
compatible = "simple-bus";
#address-cells = <1>;
#size-cells = <1>;
ranges;
dma: dma-controller@01c02000 {
compatible = "allwinner,sun8i-h3-dma";
reg = <0x01c02000 0x1000>;
interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_DMA>;
resets = <&ccu RST_BUS_DMA>;
#dma-cells = <1>;
};
mmc0: mmc@01c0f000 {
/* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c0f000 0x1000>;
resets = <&ccu RST_BUS_MMC0>;
reset-names = "ahb";
interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc1: mmc@01c10000 {
/* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c10000 0x1000>;
resets = <&ccu RST_BUS_MMC1>;
reset-names = "ahb";
interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
mmc2: mmc@01c11000 {
/* compatible and clocks are in per SoC .dtsi file */
reg = <0x01c11000 0x1000>;
resets = <&ccu RST_BUS_MMC2>;
reset-names = "ahb";
interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
usb_otg: usb@01c19000 {
compatible = "allwinner,sun8i-h3-musb";
reg = <0x01c19000 0x400>;
clocks = <&ccu CLK_BUS_OTG>;
resets = <&ccu RST_BUS_OTG>;
interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "mc";
phys = <&usbphy 0>;
phy-names = "usb";
extcon = <&usbphy 0>;
status = "disabled";
};
usbphy: phy@01c19400 {
compatible = "allwinner,sun8i-h3-usb-phy";
reg = <0x01c19400 0x2c>,
<0x01c1a800 0x4>,
<0x01c1b800 0x4>,
<0x01c1c800 0x4>,
<0x01c1d800 0x4>;
reg-names = "phy_ctrl",
"pmu0",
"pmu1",
"pmu2",
"pmu3";
clocks = <&ccu CLK_USB_PHY0>,
<&ccu CLK_USB_PHY1>,
<&ccu CLK_USB_PHY2>,
<&ccu CLK_USB_PHY3>;
clock-names = "usb0_phy",
"usb1_phy",
"usb2_phy",
"usb3_phy";
resets = <&ccu RST_USB_PHY0>,
<&ccu RST_USB_PHY1>,
<&ccu RST_USB_PHY2>,
<&ccu RST_USB_PHY3>;
reset-names = "usb0_reset",
"usb1_reset",
"usb2_reset",
"usb3_reset";
status = "disabled";
#phy-cells = <1>;
};
ehci0: usb@01c1a000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1a000 0x100>;
interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>;
resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
status = "disabled";
};
ohci0: usb@01c1a400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1a400 0x100>;
interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI0>, <&ccu CLK_BUS_OHCI0>,
<&ccu CLK_USB_OHCI0>;
resets = <&ccu RST_BUS_EHCI0>, <&ccu RST_BUS_OHCI0>;
status = "disabled";
};
ehci1: usb@01c1b000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1b000 0x100>;
interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
ohci1: usb@01c1b400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1b400 0x100>;
interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
<&ccu CLK_USB_OHCI1>;
resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
};
ehci2: usb@01c1c000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1c000 0x100>;
interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
ohci2: usb@01c1c400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1c400 0x100>;
interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
<&ccu CLK_USB_OHCI2>;
resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
phys = <&usbphy 2>;
phy-names = "usb";
status = "disabled";
};
ehci3: usb@01c1d000 {
compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
reg = <0x01c1d000 0x100>;
interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
ohci3: usb@01c1d400 {
compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
reg = <0x01c1d400 0x100>;
interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
<&ccu CLK_USB_OHCI3>;
resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
phys = <&usbphy 3>;
phy-names = "usb";
status = "disabled";
};
ccu: clock@01c20000 {
/* compatible is in per SoC .dtsi file */
reg = <0x01c20000 0x400>;
clocks = <&osc24M>, <&osc32k>;
clock-names = "hosc", "losc";
#clock-cells = <1>;
#reset-cells = <1>;
};
pio: pinctrl@01c20800 {
/* compatible is in per SoC .dtsi file */
reg = <0x01c20800 0x400>;
interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
i2c0_pins: i2c0 {
pins = "PA11", "PA12";
function = "i2c0";
};
i2c1_pins: i2c1 {
pins = "PA18", "PA19";
function = "i2c1";
};
i2c2_pins: i2c2 {
pins = "PE12", "PE13";
function = "i2c2";
};
mmc0_pins_a: mmc0@0 {
pins = "PF0", "PF1", "PF2", "PF3",
"PF4", "PF5";
function = "mmc0";
drive-strength = <30>;
bias-pull-up;
};
mmc0_cd_pin: mmc0_cd_pin@0 {
pins = "PF6";
function = "gpio_in";
bias-pull-up;
};
mmc1_pins_a: mmc1@0 {
pins = "PG0", "PG1", "PG2", "PG3",
"PG4", "PG5";
function = "mmc1";
drive-strength = <30>;
bias-pull-up;
};
mmc2_8bit_pins: mmc2_8bit {
pins = "PC5", "PC6", "PC8",
"PC9", "PC10", "PC11",
"PC12", "PC13", "PC14",
"PC15", "PC16";
function = "mmc2";
drive-strength = <30>;
bias-pull-up;
};
spdif_tx_pins_a: spdif@0 {
pins = "PA17";
function = "spdif";
};
spi0_pins: spi0 {
pins = "PC0", "PC1", "PC2", "PC3";
function = "spi0";
};
spi1_pins: spi1 {
pins = "PA15", "PA16", "PA14", "PA13";
function = "spi1";
};
uart0_pins_a: uart0@0 {
pins = "PA4", "PA5";
function = "uart0";
};
uart1_pins: uart1 {
pins = "PG6", "PG7";
function = "uart1";
};
uart1_rts_cts_pins: uart1_rts_cts {
pins = "PG8", "PG9";
function = "uart1";
};
uart2_pins: uart2 {
pins = "PA0", "PA1";
function = "uart2";
};
uart3_pins: uart3 {
pins = "PA13", "PA14";
function = "uart3";
};
};
timer@01c20c00 {
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0xa0>;
interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&osc24M>;
};
spi0: spi@01c68000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c68000 0x1000>;
interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma 23>, <&dma 23>;
dma-names = "rx", "tx";
pinctrl-names = "default";
pinctrl-0 = <&spi0_pins>;
resets = <&ccu RST_BUS_SPI0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
spi1: spi@01c69000 {
compatible = "allwinner,sun8i-h3-spi";
reg = <0x01c69000 0x1000>;
interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma 24>, <&dma 24>;
dma-names = "rx", "tx";
pinctrl-names = "default";
pinctrl-0 = <&spi1_pins>;
resets = <&ccu RST_BUS_SPI1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
wdt0: watchdog@01c20ca0 {
compatible = "allwinner,sun6i-a31-wdt";
reg = <0x01c20ca0 0x20>;
interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
};
spdif: spdif@01c21000 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-spdif";
reg = <0x01c21000 0x400>;
interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_SPDIF>, <&ccu CLK_SPDIF>;
resets = <&ccu RST_BUS_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma 2>;
dma-names = "tx";
status = "disabled";
};
pwm: pwm@01c21400 {
compatible = "allwinner,sun8i-h3-pwm";
reg = <0x01c21400 0x8>;
clocks = <&osc24M>;
#pwm-cells = <3>;
status = "disabled";
};
codec: codec@01c22c00 {
#sound-dai-cells = <0>;
compatible = "allwinner,sun8i-h3-codec";
reg = <0x01c22c00 0x400>;
interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_CODEC>, <&ccu CLK_AC_DIG>;
clock-names = "apb", "codec";
resets = <&ccu RST_BUS_CODEC>;
dmas = <&dma 15>, <&dma 15>;
dma-names = "rx", "tx";
allwinner,codec-analog-controls = <&codec_analog>;
status = "disabled";
};
uart0: serial@01c28000 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28000 0x400>;
interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART0>;
resets = <&ccu RST_BUS_UART0>;
dmas = <&dma 6>, <&dma 6>;
dma-names = "rx", "tx";
status = "disabled";
};
uart1: serial@01c28400 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28400 0x400>;
interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART1>;
resets = <&ccu RST_BUS_UART1>;
dmas = <&dma 7>, <&dma 7>;
dma-names = "rx", "tx";
status = "disabled";
};
uart2: serial@01c28800 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28800 0x400>;
interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART2>;
resets = <&ccu RST_BUS_UART2>;
dmas = <&dma 8>, <&dma 8>;
dma-names = "rx", "tx";
status = "disabled";
};
uart3: serial@01c28c00 {
compatible = "snps,dw-apb-uart";
reg = <0x01c28c00 0x400>;
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
reg-shift = <2>;
reg-io-width = <4>;
clocks = <&ccu CLK_BUS_UART3>;
resets = <&ccu RST_BUS_UART3>;
dmas = <&dma 9>, <&dma 9>;
dma-names = "rx", "tx";
status = "disabled";
};
i2c0: i2c@01c2ac00 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C0>;
resets = <&ccu RST_BUS_I2C0>;
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c1: i2c@01c2b000 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C1>;
resets = <&ccu RST_BUS_I2C1>;
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
i2c2: i2c@01c2b400 {
compatible = "allwinner,sun6i-a31-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&ccu CLK_BUS_I2C2>;
resets = <&ccu RST_BUS_I2C2>;
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
};
gic: interrupt-controller@01c81000 {
compatible = "arm,gic-400";
reg = <0x01c81000 0x1000>,
<0x01c82000 0x2000>,
<0x01c84000 0x2000>,
<0x01c86000 0x2000>;
interrupt-controller;
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
rtc: rtc@01f00000 {
compatible = "allwinner,sun6i-a31-rtc";
reg = <0x01f00000 0x54>;
interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
};
apb0_reset: reset@01f014b0 {
reg = <0x01f014b0 0x4>;
compatible = "allwinner,sun6i-a31-clock-reset";
#reset-cells = <1>;
};
codec_analog: codec-analog@01f015c0 {
compatible = "allwinner,sun8i-h3-codec-analog";
reg = <0x01f015c0 0x4>;
};
ir: ir@01f02000 {
compatible = "allwinner,sun5i-a13-ir";
clocks = <&apb0_gates 1>, <&ir_clk>;
clock-names = "apb", "ir";
resets = <&apb0_reset 1>;
interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
reg = <0x01f02000 0x40>;
status = "disabled";
};
r_pio: pinctrl@01f02c00 {
compatible = "allwinner,sun8i-h3-r-pinctrl";
reg = <0x01f02c00 0x400>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
resets = <&apb0_reset 0>;
gpio-controller;
#gpio-cells = <3>;
interrupt-controller;
#interrupt-cells = <3>;
ir_pins_a: ir@0 {
pins = "PL11";
function = "s_cir_rx";
};
};
};
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7