Commit aa9772e3 authored by Ralf Baechle's avatar Ralf Baechle

[MIPS] SN: Rename SGI_SN0_N_MODE -> SGI_SN_N_MODE.

It's not SN0-specific.
Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent bf5a312b
...@@ -63,7 +63,7 @@ CONFIG_SGI_IP27=y ...@@ -63,7 +63,7 @@ CONFIG_SGI_IP27=y
# CONFIG_TOSHIBA_JMR3927 is not set # CONFIG_TOSHIBA_JMR3927 is not set
# CONFIG_TOSHIBA_RBTX4927 is not set # CONFIG_TOSHIBA_RBTX4927 is not set
# CONFIG_TOSHIBA_RBTX4938 is not set # CONFIG_TOSHIBA_RBTX4938 is not set
# CONFIG_SGI_SN0_N_MODE is not set # CONFIG_SGI_SN_N_MODE is not set
CONFIG_ARCH_DISCONTIGMEM_ENABLE=y CONFIG_ARCH_DISCONTIGMEM_ENABLE=y
CONFIG_NUMA=y CONFIG_NUMA=y
# CONFIG_MAPPED_KERNEL is not set # CONFIG_MAPPED_KERNEL is not set
......
...@@ -4,7 +4,7 @@ ...@@ -4,7 +4,7 @@
# This options adds support for userspace processes upto 16TB size. # This options adds support for userspace processes upto 16TB size.
# Normally the limit is just .5TB. # Normally the limit is just .5TB.
config SGI_SN0_N_MODE config SGI_SN_N_MODE
bool "IP27 N-Mode" bool "IP27 N-Mode"
depends on SGI_IP27 depends on SGI_IP27
help help
......
...@@ -228,7 +228,7 @@ void __init plat_setup(void) ...@@ -228,7 +228,7 @@ void __init plat_setup(void)
*/ */
n_mode = LOCAL_HUB_L(NI_STATUS_REV_ID) & NSRI_MORENODES_MASK; n_mode = LOCAL_HUB_L(NI_STATUS_REV_ID) & NSRI_MORENODES_MASK;
printk("Machine is in %c mode.\n", n_mode ? 'N' : 'M'); printk("Machine is in %c mode.\n", n_mode ? 'N' : 'M');
#ifdef CONFIG_SGI_SN0_N_MODE #ifdef CONFIG_SGI_SN_N_MODE
if (!n_mode) if (!n_mode)
panic("Kernel compiled for M mode."); panic("Kernel compiled for M mode.");
#else #else
......
...@@ -49,7 +49,7 @@ ...@@ -49,7 +49,7 @@
* so for now we just use defines bracketed by an ifdef. * so for now we just use defines bracketed by an ifdef.
*/ */
#ifdef CONFIG_SGI_SN0_N_MODE #ifdef CONFIG_SGI_SN_N_MODE
#define NODE_SIZE_BITS 31 #define NODE_SIZE_BITS 31
#define BWIN_SIZE_BITS 28 #define BWIN_SIZE_BITS 28
...@@ -63,7 +63,7 @@ ...@@ -63,7 +63,7 @@
#define BDDIR_UPPER_MASK (UINT64_CAST 0x7ffff << 10) #define BDDIR_UPPER_MASK (UINT64_CAST 0x7ffff << 10)
#define BDECC_UPPER_MASK (UINT64_CAST 0x3ffffff << 3) #define BDECC_UPPER_MASK (UINT64_CAST 0x3ffffff << 3)
#else /* !defined(CONFIG_SGI_SN0_N_MODE), assume that M-mode is desired */ #else /* !defined(CONFIG_SGI_SN_N_MODE), assume that M-mode is desired */
#define NODE_SIZE_BITS 32 #define NODE_SIZE_BITS 32
#define BWIN_SIZE_BITS 29 #define BWIN_SIZE_BITS 29
...@@ -77,7 +77,7 @@ ...@@ -77,7 +77,7 @@
#define BDDIR_UPPER_MASK (UINT64_CAST 0xfffff << 10) #define BDDIR_UPPER_MASK (UINT64_CAST 0xfffff << 10)
#define BDECC_UPPER_MASK (UINT64_CAST 0x7ffffff << 3) #define BDECC_UPPER_MASK (UINT64_CAST 0x7ffffff << 3)
#endif /* !defined(CONFIG_SGI_SN0_N_MODE) */ #endif /* !defined(CONFIG_SGI_SN_N_MODE) */
#define NODE_ADDRSPACE_SIZE (UINT64_CAST 1 << NODE_SIZE_BITS) #define NODE_ADDRSPACE_SIZE (UINT64_CAST 1 << NODE_SIZE_BITS)
......
...@@ -57,9 +57,9 @@ ...@@ -57,9 +57,9 @@
/* /*
* Slot constants for SN0 * Slot constants for SN0
*/ */
#ifdef CONFIG_SGI_SN0_N_MODE #ifdef CONFIG_SGI_SN_N_MODE
#define MAX_MEM_SLOTS 16 /* max slots per node */ #define MAX_MEM_SLOTS 16 /* max slots per node */
#else /* !CONFIG_SGI_SN0_N_MODE, assume M_MODE */ #else /* !CONFIG_SGI_SN_N_MODE, assume M_MODE */
#define MAX_MEM_SLOTS 32 /* max slots per node */ #define MAX_MEM_SLOTS 32 /* max slots per node */
#endif /* defined(N_MODE) */ #endif /* defined(N_MODE) */
......
...@@ -92,7 +92,7 @@ ...@@ -92,7 +92,7 @@
#define MD_UREG1_14 0x2200f0 /* uController/UART 1 register */ #define MD_UREG1_14 0x2200f0 /* uController/UART 1 register */
#define MD_UREG1_15 0x2200f8 /* uController/UART 1 register */ #define MD_UREG1_15 0x2200f8 /* uController/UART 1 register */
#ifdef CONFIG_SGI_SN0_N_MODE #ifdef CONFIG_SGI_SN_N_MODE
#define MD_MEM_BANKS 4 /* 4 banks of memory max in N mode */ #define MD_MEM_BANKS 4 /* 4 banks of memory max in N mode */
#else #else
#define MD_MEM_BANKS 8 /* 8 banks of memory max in M mode */ #define MD_MEM_BANKS 8 /* 8 banks of memory max in M mode */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment