Merge tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi

Pull spi fixes from Mark Brown:
 "A few nasty issues, particularly a race with the interrupt controller
  in the xilinx driver, together with a couple of more minor fixes and a
  much needed move of the mailing list away from sourceforge."

* tag 'spi-v3.10-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
  spi: hspi: fixup long delay time
  spi: spi-xilinx: Remove ISR race condition
  spi: topcliff-pch: fix error return code in pch_spi_probe()
  spi: topcliff-pch: Pass correct pointer to free_irq()
  spi: Move mailing list to vger

MAINTAINERS

@@ -7624,7 +7624,7 @@ F:	drivers/clk/spear/
 SPI SUBSYSTEM
 M:	Mark Brown <broonie@kernel.org>
 M:	Grant Likely <grant.likely@linaro.org>
-L:	spi-devel-general@lists.sourceforge.net
+L:	linux-spi@vger.kernel.org
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git
 Q:	http://patchwork.kernel.org/project/spi-devel-general/list/
 S:	Maintained

drivers/spi/spi-sh-hspi.c

@@ -89,7 +89,7 @@ static int hspi_status_check_timeout(struct hspi_priv *hspi, u32 mask, u32 val)
 		if ((mask & hspi_read(hspi, SPSR)) == val)
 			return 0;
 
-		msleep(20);
+		udelay(10);
 	}
 
 	dev_err(hspi->dev, "timeout\n");

drivers/spi/spi-topcliff-pch.c

@@ -1487,7 +1487,7 @@ static int pch_spi_pd_probe(struct platform_device *plat_dev)
 	return 0;
 
 err_spi_register_master:
-	free_irq(board_dat->pdev->irq, board_dat);
+	free_irq(board_dat->pdev->irq, data);
 err_request_irq:
 	pch_spi_free_resources(board_dat, data);
 err_spi_get_resources:
@@ -1667,6 +1667,7 @@ static int pch_spi_probe(struct pci_dev *pdev,
 		pd_dev = platform_device_alloc("pch-spi", i);
 		if (!pd_dev) {
 			dev_err(&pdev->dev, "platform_device_alloc failed\n");
+			retval = -ENOMEM;
 			goto err_platform_device;
 		}
 		pd_dev_save->pd_save[i] = pd_dev;

drivers/spi/spi-xilinx.c

@@ -267,7 +267,6 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 {
 	struct xilinx_spi *xspi = spi_master_get_devdata(spi->master);
 	u32 ipif_ier;
-	u16 cr;
 
 	/* We get here with transmitter inhibited */
 
@@ -276,7 +275,6 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 	xspi->remaining_bytes = t->len;
 	INIT_COMPLETION(xspi->done);
 
-	xilinx_spi_fill_tx_fifo(xspi);
 
 	/* Enable the transmit empty interrupt, which we use to determine
 	 * progress on the transmission.
@@ -285,13 +283,42 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t)
 	xspi->write_fn(ipif_ier | XSPI_INTR_TX_EMPTY,
 		xspi->regs + XIPIF_V123B_IIER_OFFSET);
 
-	/* Start the transfer by not inhibiting the transmitter any longer */
+	for (;;) {
+		u16 cr;
+		u8 sr;
+
+		xilinx_spi_fill_tx_fifo(xspi);
+
+		/* Start the transfer by not inhibiting the transmitter any
+		 * longer
+		 */
 		cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET) &
 							~XSPI_CR_TRANS_INHIBIT;
 		xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
 
 		wait_for_completion(&xspi->done);
 
+		/* A transmit has just completed. Process received data and
+		 * check for more data to transmit. Always inhibit the
+		 * transmitter while the Isr refills the transmit register/FIFO,
+		 * or make sure it is stopped if we're done.
+		 */
+		cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
+		xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
+			       xspi->regs + XSPI_CR_OFFSET);
+
+		/* Read out all the data from the Rx FIFO */
+		sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
+		while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
+			xspi->rx_fn(xspi);
+			sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
+		}
+
+		/* See if there is more data to send */
+		if (!xspi->remaining_bytes > 0)
+			break;
+	}
+
 	/* Disable the transmit empty interrupt */
 	xspi->write_fn(ipif_ier, xspi->regs + XIPIF_V123B_IIER_OFFSET);
 
@@ -314,39 +341,8 @@ static irqreturn_t xilinx_spi_irq(int irq, void *dev_id)
 	xspi->write_fn(ipif_isr, xspi->regs + XIPIF_V123B_IISR_OFFSET);
 
 	if (ipif_isr & XSPI_INTR_TX_EMPTY) {	/* Transmission completed */
-		u16 cr;
-		u8 sr;
-
-		/* A transmit has just completed. Process received data and
-		 * check for more data to transmit. Always inhibit the
-		 * transmitter while the Isr refills the transmit register/FIFO,
-		 * or make sure it is stopped if we're done.
-		 */
-		cr = xspi->read_fn(xspi->regs + XSPI_CR_OFFSET);
-		xspi->write_fn(cr | XSPI_CR_TRANS_INHIBIT,
-			xspi->regs + XSPI_CR_OFFSET);
-
-		/* Read out all the data from the Rx FIFO */
-		sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
-		while ((sr & XSPI_SR_RX_EMPTY_MASK) == 0) {
-			xspi->rx_fn(xspi);
-			sr = xspi->read_fn(xspi->regs + XSPI_SR_OFFSET);
-		}
-
-		/* See if there is more data to send */
-		if (xspi->remaining_bytes > 0) {
-			xilinx_spi_fill_tx_fifo(xspi);
-			/* Start the transfer by not inhibiting the
-			 * transmitter any longer
-			 */
-			xspi->write_fn(cr, xspi->regs + XSPI_CR_OFFSET);
-		} else {
-			/* No more data to send.
-			 * Indicate the transfer is completed.
-			 */
 		complete(&xspi->done);
 	}
-	}
 
 	return IRQ_HANDLED;
 }