Commit abd37ccc authored by Sascha Hauer's avatar Sascha Hauer Committed by Chris Ball

mmc: mxs: use mmc_gpio_get_ro for detecting read-only status

This also fixes that the read-only gpio was used without being
requested.
Signed-off-by: default avatarSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: default avatarChris Ball <cjb@laptop.org>
parent 6c3331d3
......@@ -38,6 +38,7 @@
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h>
#include <linux/mmc/sdio.h>
#include <linux/mmc/slot-gpio.h>
#include <linux/gpio.h>
#include <linux/regulator/consumer.h>
#include <linux/module.h>
......@@ -69,26 +70,8 @@ struct mxs_mmc_host {
unsigned char bus_width;
spinlock_t lock;
int sdio_irq_en;
int wp_gpio;
bool wp_inverted;
};
static int mxs_mmc_get_ro(struct mmc_host *mmc)
{
struct mxs_mmc_host *host = mmc_priv(mmc);
int ret;
if (!gpio_is_valid(host->wp_gpio))
return -EINVAL;
ret = gpio_get_value(host->wp_gpio);
if (host->wp_inverted)
ret = !ret;
return ret;
}
static int mxs_mmc_get_cd(struct mmc_host *mmc)
{
struct mxs_mmc_host *host = mmc_priv(mmc);
......@@ -551,7 +534,7 @@ static void mxs_mmc_enable_sdio_irq(struct mmc_host *mmc, int enable)
static const struct mmc_host_ops mxs_mmc_ops = {
.request = mxs_mmc_request,
.get_ro = mxs_mmc_get_ro,
.get_ro = mmc_gpio_get_ro,
.get_cd = mxs_mmc_get_cd,
.set_ios = mxs_mmc_set_ios,
.enable_sdio_irq = mxs_mmc_enable_sdio_irq,
......@@ -585,7 +568,7 @@ static int mxs_mmc_probe(struct platform_device *pdev)
struct mxs_mmc_host *host;
struct mmc_host *mmc;
struct resource *iores;
int ret = 0, irq_err;
int ret = 0, irq_err, gpio;
struct regulator *reg_vmmc;
enum of_gpio_flags flags;
struct mxs_ssp *ssp;
......@@ -659,9 +642,14 @@ static int mxs_mmc_probe(struct platform_device *pdev)
mmc->caps |= MMC_CAP_NEEDS_POLL;
if (of_property_read_bool(np, "non-removable"))
mmc->caps |= MMC_CAP_NONREMOVABLE;
host->wp_gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
if (flags & OF_GPIO_ACTIVE_LOW)
host->wp_inverted = 1;
gpio = of_get_named_gpio_flags(np, "wp-gpios", 0, &flags);
if (gpio_is_valid(gpio)) {
ret = mmc_gpio_request_ro(mmc, gpio);
if (ret)
goto out_clk_disable;
if (!(flags & OF_GPIO_ACTIVE_LOW))
mmc->caps2 |= MMC_CAP2_RO_ACTIVE_HIGH;
}
if (of_property_read_bool(np, "cd-inverted"))
mmc->caps2 |= MMC_CAP2_CD_ACTIVE_HIGH;
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment