Merge tag 'sh-pfc-for-v5.9-tag2' of...

Merge tag 'sh-pfc-for-v5.9-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel

pinctrl: sh-pfc: Updates for v5.9 (take two)

  - Add support for the new RZ/G2H (R8A774E1) SoC,
  - One more conversion of DT bindings to json-schema,
  - Fix RZ/A1 kerneldoc.

Documentation/devicetree/bindings/pinctrl/renesas,pfc-pinctrl.txt

@@ -21,6 +21,7 @@ Required Properties:
     - "renesas,pfc-r8a774a1": for R8A774A1 (RZ/G2M) compatible pin-controller.
     - "renesas,pfc-r8a774b1": for R8A774B1 (RZ/G2N) compatible pin-controller.
     - "renesas,pfc-r8a774c0": for R8A774C0 (RZ/G2E) compatible pin-controller.
+    - "renesas,pfc-r8a774e1": for R8A774E1 (RZ/G2H) compatible pin-controller.
     - "renesas,pfc-r8a7778": for R8A7778 (R-Car M1) compatible pin-controller.
     - "renesas,pfc-r8a7779": for R8A7779 (R-Car H1) compatible pin-controller.
     - "renesas,pfc-r8a7790": for R8A7790 (R-Car H2) compatible pin-controller.

Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.txt

-Renesas RZ/A2 combined Pin and GPIO controller
-
-The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO controller.
-Pin multiplexing and GPIO configuration is performed on a per-pin basis.
-Each port features up to 8 pins, each of them configurable for GPIO
-function (port mode) or in alternate function mode.
-Up to 8 different alternate function modes exist for each single pin.
-
-Pin controller node
--------------------
-
-Required properties:
-  - compatible: shall be:
-    - "renesas,r7s9210-pinctrl": for RZ/A2M
-  - reg
-    Address base and length of the memory area where the pin controller
-    hardware is mapped to.
-  - gpio-controller
-    This pin controller also controls pins as GPIO
-  - #gpio-cells
-    Must be 2
-  - gpio-ranges
-    Expresses the total number of GPIO ports/pins in this SoC
-
-Example: Pin controller node for RZ/A2M SoC (r7s9210)
-
-	pinctrl: pin-controller@fcffe000 {
-		compatible = "renesas,r7s9210-pinctrl";
-		reg = <0xfcffe000 0x1000>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-		gpio-ranges = <&pinctrl 0 0 176>;
-	};
-
-Sub-nodes
----------
-
-The child nodes of the pin controller designate pins to be used for
-specific peripheral functions or as GPIO.
-
-- Pin multiplexing sub-nodes:
-  A pin multiplexing sub-node describes how to configure a set of
-  (or a single) pin in some desired alternate function mode.
-  The values for the pinmux properties are a combination of port name, pin
-  number and the desired function index. Use the RZA2_PINMUX macro located
-  in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily define these.
-  For assigning GPIO pins, use the macro RZA2_PIN also in r7s9210-pinctrl.h
-  to express the desired port pin.
-
-  Required properties:
-    - pinmux:
-      integer array representing pin number and pin multiplexing configuration.
-      When a pin has to be configured in alternate function mode, use this
-      property to identify the pin by its global index, and provide its
-      alternate function configuration number along with it.
-      When multiple pins are required to be configured as part of the same
-      alternate function they shall be specified as members of the same
-      argument list of a single "pinmux" property.
-      Helper macros to ease assembling the pin index from its position
-      (port where it sits on and pin number) and alternate function identifier
-      are provided by the pin controller header file at:
-      <dt-bindings/pinctrl/r7s9210-pinctrl.h>
-      Integers values in "pinmux" argument list are assembled as:
-      ((PORT * 8 + PIN) | MUX_FUNC << 16)
-
-  Example: Board specific pins configuration
-
-	&pinctrl {
-		/* Serial Console */
-		scif4_pins: serial4 {
-			pinmux = <RZA2_PINMUX(PORT9, 0, 4)>,	/* TxD4 */
-				 <RZA2_PINMUX(PORT9, 1, 4)>;	/* RxD4 */
-		};
-	};
-
-  Example: Assigning a GPIO:
-
-	leds {
-		status = "okay";
-		compatible = "gpio-leds";
-
-		led0 {
-			/* P6_0 */
-			gpios = <&pinctrl RZA2_PIN(PORT6, 0) GPIO_ACTIVE_HIGH>;
-		};
-	};

Documentation/devicetree/bindings/pinctrl/renesas,rza2-pinctrl.yaml

+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/renesas,rza2-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Renesas RZ/A2 combined Pin and GPIO controller
+
+maintainers:
+  - Chris Brandt <chris.brandt@renesas.com>
+  - Geert Uytterhoeven <geert+renesas@glider.be>
+
+description:
+  The Renesas SoCs of the RZ/A2 series feature a combined Pin and GPIO
+  controller.
+  Pin multiplexing and GPIO configuration is performed on a per-pin basis.
+  Each port features up to 8 pins, each of them configurable for GPIO function
+  (port mode) or in alternate function mode.
+  Up to 8 different alternate function modes exist for each single pin.
+
+properties:
+  compatible:
+    const: "renesas,r7s9210-pinctrl" # RZ/A2M
+
+  reg:
+    maxItems: 1
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    const: 2
+    description:
+      The first cell contains the global GPIO port index, constructed using the
+      RZA2_PIN() helper macro in r7s9210-pinctrl.h.
+      E.g. "RZA2_PIN(PORT6, 0)" for P6_0.
+
+  gpio-ranges:
+    maxItems: 1
+
+patternProperties:
+  "^.*$":
+    if:
+      type: object
+    then:
+      allOf:
+        - $ref: pincfg-node.yaml#
+        - $ref: pinmux-node.yaml#
+      description:
+        The child nodes of the pin controller designate pins to be used for
+        specific peripheral functions or as GPIO.
+
+        A pin multiplexing sub-node describes how to configure a set of
+        (or a single) pin in some desired alternate function mode.
+        The values for the pinmux properties are a combination of port name,
+        pin number and the desired function index. Use the RZA2_PINMUX macro
+        located in include/dt-bindings/pinctrl/r7s9210-pinctrl.h to easily
+        define these.
+        For assigning GPIO pins, use the macro RZA2_PIN also in
+        to express the desired port pin.
+
+      properties:
+        phandle: true
+
+        pinmux:
+          description:
+            Values are constructed from GPIO port number, pin number, and
+            alternate function configuration number using the RZA2_PINMUX()
+            helper macro in r7s9210-pinctrl.h.
+
+      required:
+        - pinmux
+
+      additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/pinctrl/r7s9210-pinctrl.h>
+    pinctrl: pin-controller@fcffe000 {
+            compatible = "renesas,r7s9210-pinctrl";
+            reg = <0xfcffe000 0x1000>;
+
+            gpio-controller;
+            #gpio-cells = <2>;
+            gpio-ranges = <&pinctrl 0 0 176>;
+
+            /* Serial Console */
+            scif4_pins: serial4 {
+                    pinmux = <RZA2_PINMUX(PORT9, 0, 4)>, /* TxD4 */
+                             <RZA2_PINMUX(PORT9, 1, 4)>; /* RxD4 */
+            };
+    };

drivers/pinctrl/pinctrl-rza1.c

@@ -75,7 +75,7 @@
  * RZ/A1 pinmux flags
  */
 
-/**
+/*
  * rza1_bidir_pin - describe a single pin that needs bidir flag applied.
  */
 struct rza1_bidir_pin {
@@ -83,7 +83,7 @@ struct rza1_bidir_pin {
 	u8 func: 4;
 };
 
-/**
+/*
  * rza1_bidir_entry - describe a list of pins that needs bidir flag applied.
  *		      Each struct rza1_bidir_entry describes a port.
  */
@@ -92,7 +92,7 @@ struct rza1_bidir_entry {
 	const struct rza1_bidir_pin *pins;
 };
 
-/**
+/*
  * rza1_swio_pin - describe a single pin that needs swio flag applied.
  */
 struct rza1_swio_pin {
@@ -102,7 +102,7 @@ struct rza1_swio_pin {
 	u16 input: 1;
 };
 
-/**
+/*
  * rza1_swio_entry - describe a list of pins that needs swio flag applied
  */
 struct rza1_swio_entry {
@@ -110,7 +110,7 @@ struct rza1_swio_entry {
 	const struct rza1_swio_pin *pins;
 };
 
-/**
+/*
  * rza1_pinmux_conf - group together bidir and swio pinmux flag tables
  */
 struct rza1_pinmux_conf {
@@ -431,7 +431,7 @@ static const struct rza1_pinmux_conf rza1l_pmx_conf = {
  * RZ/A1 types
  */
 /**
- * rza1_mux_conf - describes a pin multiplexing operation
+ * struct rza1_mux_conf - describes a pin multiplexing operation
  *
  * @id: the pin identifier from 0 to RZA1_NPINS
  * @port: the port where pin sits on
@@ -450,7 +450,7 @@ struct rza1_mux_conf {
 };
 
 /**
- * rza1_port - describes a pin port
+ * struct rza1_port - describes a pin port
  *
  * This is mostly useful to lock register writes per-bank and not globally.
  *
@@ -467,12 +467,12 @@ struct rza1_port {
 };
 
 /**
- * rza1_pinctrl - RZ pincontroller device
+ * struct rza1_pinctrl - RZ pincontroller device
  *
  * @dev: parent device structure
  * @mutex: protect [pinctrl|pinmux]_generic functions
  * @base: logical address base
- * @nports: number of pin controller ports
+ * @nport: number of pin controller ports
  * @ports: pin controller banks
  * @pins: pin array for pinctrl core
  * @desc: pincontroller desc for pinctrl core
@@ -536,7 +536,7 @@ static inline int rza1_pinmux_get_swio(unsigned int port,
 	return -ENOENT;
 }
 
-/**
+/*
  * rza1_pinmux_get_flags() - return pinmux flags associated to a pin
  */
 static unsigned int rza1_pinmux_get_flags(unsigned int port, unsigned int pin,
@@ -566,7 +566,7 @@ static unsigned int rza1_pinmux_get_flags(unsigned int port, unsigned int pin,
  * RZ/A1 SoC operations
  */
 
-/**
+/*
  * rza1_set_bit() - un-locked set/clear a single bit in pin configuration
  *		    registers
  */
@@ -664,7 +664,7 @@ static inline int rza1_pin_get(struct rza1_port *port, unsigned int pin)
 /**
  * rza1_pin_mux_single() - configure pin multiplexing on a single pin
  *
- * @pinctrl: RZ/A1 pin controller device
+ * @rza1_pctl: RZ/A1 pin controller device
  * @mux_conf: pin multiplexing descriptor
  */
 static int rza1_pin_mux_single(struct rza1_pinctrl *rza1_pctl,

drivers/pinctrl/sh-pfc/Kconfig

@@ -20,6 +20,7 @@ config PINCTRL_SH_PFC
 	select PINCTRL_PFC_R8A774A1 if ARCH_R8A774A1
 	select PINCTRL_PFC_R8A774B1 if ARCH_R8A774B1
 	select PINCTRL_PFC_R8A774C0 if ARCH_R8A774C0
+	select PINCTRL_PFC_R8A774E1 if ARCH_R8A774E1
 	select PINCTRL_PFC_R8A7778 if ARCH_R8A7778
 	select PINCTRL_PFC_R8A7779 if ARCH_R8A7779
 	select PINCTRL_PFC_R8A7790 if ARCH_R8A7790
@@ -99,6 +100,9 @@ config PINCTRL_PFC_R8A774B1
 config PINCTRL_PFC_R8A774C0
 	bool "RZ/G2E pin control support" if COMPILE_TEST
 
+config PINCTRL_PFC_R8A774E1
+	bool "RZ/G2H pin control support" if COMPILE_TEST
+
 config PINCTRL_PFC_R8A7778
 	bool "R-Car M1A pin control support" if COMPILE_TEST
 

drivers/pinctrl/sh-pfc/Makefile

@@ -12,6 +12,7 @@ obj-$(CONFIG_PINCTRL_PFC_R8A77470)	+= pfc-r8a77470.o
 obj-$(CONFIG_PINCTRL_PFC_R8A774A1)	+= pfc-r8a7796.o
 obj-$(CONFIG_PINCTRL_PFC_R8A774B1)	+= pfc-r8a77965.o
 obj-$(CONFIG_PINCTRL_PFC_R8A774C0)	+= pfc-r8a77990.o
+obj-$(CONFIG_PINCTRL_PFC_R8A774E1)	+= pfc-r8a77951.o
 obj-$(CONFIG_PINCTRL_PFC_R8A7778)	+= pfc-r8a7778.o
 obj-$(CONFIG_PINCTRL_PFC_R8A7779)	+= pfc-r8a7779.o
 obj-$(CONFIG_PINCTRL_PFC_R8A7790)	+= pfc-r8a7790.o

drivers/pinctrl/sh-pfc/core.c

@@ -533,6 +533,12 @@ static const struct of_device_id sh_pfc_of_table[] = {
 		.data = &r8a774c0_pinmux_info,
 	},
 #endif
+#ifdef CONFIG_PINCTRL_PFC_R8A774E1
+	{
+		.compatible = "renesas,pfc-r8a774e1",
+		.data = &r8a774e1_pinmux_info,
+	},
+#endif
 #ifdef CONFIG_PINCTRL_PFC_R8A7778
 	{
 		.compatible = "renesas,pfc-r8a7778",

drivers/pinctrl/sh-pfc/pfc-r8a77951.c

@@ -4157,7 +4157,11 @@ static const unsigned int vin5_clk_mux[] = {
 	VI5_CLK_MARK,
 };
 
-static const struct sh_pfc_pin_group pinmux_groups[] = {
+static const struct {
+	struct sh_pfc_pin_group common[320];
+	struct sh_pfc_pin_group automotive[30];
+} pinmux_groups = {
+	.common = {
 		SH_PFC_PIN_GROUP(audio_clk_a_a),
 		SH_PFC_PIN_GROUP(audio_clk_a_b),
 		SH_PFC_PIN_GROUP(audio_clk_a_c),
@@ -4193,36 +4197,6 @@ static const struct sh_pfc_pin_group pinmux_groups[] = {
 		SH_PFC_PIN_GROUP(canfd0_data_a),
 		SH_PFC_PIN_GROUP(canfd0_data_b),
 		SH_PFC_PIN_GROUP(canfd1_data),
-	SH_PFC_PIN_GROUP(drif0_ctrl_a),
-	SH_PFC_PIN_GROUP(drif0_data0_a),
-	SH_PFC_PIN_GROUP(drif0_data1_a),
-	SH_PFC_PIN_GROUP(drif0_ctrl_b),
-	SH_PFC_PIN_GROUP(drif0_data0_b),
-	SH_PFC_PIN_GROUP(drif0_data1_b),
-	SH_PFC_PIN_GROUP(drif0_ctrl_c),
-	SH_PFC_PIN_GROUP(drif0_data0_c),
-	SH_PFC_PIN_GROUP(drif0_data1_c),
-	SH_PFC_PIN_GROUP(drif1_ctrl_a),
-	SH_PFC_PIN_GROUP(drif1_data0_a),
-	SH_PFC_PIN_GROUP(drif1_data1_a),
-	SH_PFC_PIN_GROUP(drif1_ctrl_b),
-	SH_PFC_PIN_GROUP(drif1_data0_b),
-	SH_PFC_PIN_GROUP(drif1_data1_b),
-	SH_PFC_PIN_GROUP(drif1_ctrl_c),
-	SH_PFC_PIN_GROUP(drif1_data0_c),
-	SH_PFC_PIN_GROUP(drif1_data1_c),
-	SH_PFC_PIN_GROUP(drif2_ctrl_a),
-	SH_PFC_PIN_GROUP(drif2_data0_a),
-	SH_PFC_PIN_GROUP(drif2_data1_a),
-	SH_PFC_PIN_GROUP(drif2_ctrl_b),
-	SH_PFC_PIN_GROUP(drif2_data0_b),
-	SH_PFC_PIN_GROUP(drif2_data1_b),
-	SH_PFC_PIN_GROUP(drif3_ctrl_a),
-	SH_PFC_PIN_GROUP(drif3_data0_a),
-	SH_PFC_PIN_GROUP(drif3_data1_a),
-	SH_PFC_PIN_GROUP(drif3_ctrl_b),
-	SH_PFC_PIN_GROUP(drif3_data0_b),
-	SH_PFC_PIN_GROUP(drif3_data1_b),
 		SH_PFC_PIN_GROUP(du_rgb666),
 		SH_PFC_PIN_GROUP(du_rgb888),
 		SH_PFC_PIN_GROUP(du_clk_out_0),
@@ -4508,6 +4482,40 @@ static const struct sh_pfc_pin_group pinmux_groups[] = {
 		SH_PFC_PIN_GROUP(vin5_field),
 		SH_PFC_PIN_GROUP(vin5_clkenb),
 		SH_PFC_PIN_GROUP(vin5_clk),
+	},
+	.automotive = {
+		SH_PFC_PIN_GROUP(drif0_ctrl_a),
+		SH_PFC_PIN_GROUP(drif0_data0_a),
+		SH_PFC_PIN_GROUP(drif0_data1_a),
+		SH_PFC_PIN_GROUP(drif0_ctrl_b),
+		SH_PFC_PIN_GROUP(drif0_data0_b),
+		SH_PFC_PIN_GROUP(drif0_data1_b),
+		SH_PFC_PIN_GROUP(drif0_ctrl_c),
+		SH_PFC_PIN_GROUP(drif0_data0_c),
+		SH_PFC_PIN_GROUP(drif0_data1_c),
+		SH_PFC_PIN_GROUP(drif1_ctrl_a),
+		SH_PFC_PIN_GROUP(drif1_data0_a),
+		SH_PFC_PIN_GROUP(drif1_data1_a),
+		SH_PFC_PIN_GROUP(drif1_ctrl_b),
+		SH_PFC_PIN_GROUP(drif1_data0_b),
+		SH_PFC_PIN_GROUP(drif1_data1_b),
+		SH_PFC_PIN_GROUP(drif1_ctrl_c),
+		SH_PFC_PIN_GROUP(drif1_data0_c),
+		SH_PFC_PIN_GROUP(drif1_data1_c),
+		SH_PFC_PIN_GROUP(drif2_ctrl_a),
+		SH_PFC_PIN_GROUP(drif2_data0_a),
+		SH_PFC_PIN_GROUP(drif2_data1_a),
+		SH_PFC_PIN_GROUP(drif2_ctrl_b),
+		SH_PFC_PIN_GROUP(drif2_data0_b),
+		SH_PFC_PIN_GROUP(drif2_data1_b),
+		SH_PFC_PIN_GROUP(drif3_ctrl_a),
+		SH_PFC_PIN_GROUP(drif3_data0_a),
+		SH_PFC_PIN_GROUP(drif3_data1_a),
+		SH_PFC_PIN_GROUP(drif3_ctrl_b),
+		SH_PFC_PIN_GROUP(drif3_data0_b),
+		SH_PFC_PIN_GROUP(drif3_data1_b),
+	}
+
 };
 
 static const char * const audio_clk_groups[] = {
@@ -5031,7 +5039,11 @@ static const char * const vin5_groups[] = {
 	"vin5_clk",
 };
 
-static const struct sh_pfc_function pinmux_functions[] = {
+static const struct {
+	struct sh_pfc_function common[53];
+	struct sh_pfc_function automotive[4];
+} pinmux_functions = {
+	.common = {
 		SH_PFC_FUNCTION(audio_clk),
 		SH_PFC_FUNCTION(avb),
 		SH_PFC_FUNCTION(can0),
@@ -5039,10 +5051,6 @@ static const struct sh_pfc_function pinmux_functions[] = {
 		SH_PFC_FUNCTION(can_clk),
 		SH_PFC_FUNCTION(canfd0),
 		SH_PFC_FUNCTION(canfd1),
-	SH_PFC_FUNCTION(drif0),
-	SH_PFC_FUNCTION(drif1),
-	SH_PFC_FUNCTION(drif2),
-	SH_PFC_FUNCTION(drif3),
 		SH_PFC_FUNCTION(du),
 		SH_PFC_FUNCTION(hscif0),
 		SH_PFC_FUNCTION(hscif1),
@@ -5089,6 +5097,14 @@ static const struct sh_pfc_function pinmux_functions[] = {
 		SH_PFC_FUNCTION(usb30),
 		SH_PFC_FUNCTION(vin4),
 		SH_PFC_FUNCTION(vin5),
+	},
+	.automotive = {
+		SH_PFC_FUNCTION(drif0),
+		SH_PFC_FUNCTION(drif1),
+		SH_PFC_FUNCTION(drif2),
+		SH_PFC_FUNCTION(drif3),
+	}
+
 };
 
 static const struct pinmux_cfg_reg pinmux_config_regs[] = {
@@ -5777,7 +5793,9 @@ static const struct pinmux_drive_reg pinmux_drive_regs[] = {
 		{ PIN_DU_DOTCLKIN1,    0, 2 },	/* DU_DOTCLKIN1 */
 	} },
 	{ PINMUX_DRIVE_REG("DRVCTRL12", 0xe6060330) {
+#ifdef CONFIG_PINCTRL_PFC_R8A77951
 		{ PIN_DU_DOTCLKIN2,   28, 2 },	/* DU_DOTCLKIN2 */
+#endif
 		{ PIN_DU_DOTCLKIN3,   24, 2 },	/* DU_DOTCLKIN3 */
 		{ PIN_FSCLKST_N,      20, 2 },	/* FSCLKST# */
 		{ PIN_TMS,             4, 2 },	/* TMS */
@@ -5898,8 +5916,8 @@ static const struct pinmux_drive_reg pinmux_drive_regs[] = {
 		{ RCAR_GP_PIN(6, 27), 20, 3 },	/* USB1_OVC */
 		{ RCAR_GP_PIN(6, 28), 16, 3 },	/* USB30_PWEN */
 		{ RCAR_GP_PIN(6, 29), 12, 3 },	/* USB30_OVC */
-		{ RCAR_GP_PIN(6, 30),  8, 3 },	/* USB2_CH3_PWEN */
-		{ RCAR_GP_PIN(6, 31),  4, 3 },	/* USB2_CH3_OVC */
+		{ RCAR_GP_PIN(6, 30),  8, 3 },	/* GP6_30/USB2_CH3_PWEN */
+		{ RCAR_GP_PIN(6, 31),  4, 3 },	/* GP6_31/USB2_CH3_OVC */
 	} },
 	{ },
 };
@@ -6220,6 +6238,32 @@ static const struct sh_pfc_soc_operations r8a77951_pinmux_ops = {
 	.set_bias = r8a77951_pinmux_set_bias,
 };
 
+#ifdef CONFIG_PINCTRL_PFC_R8A774E1
+const struct sh_pfc_soc_info r8a774e1_pinmux_info = {
+	.name = "r8a774e1_pfc",
+	.ops = &r8a77951_pinmux_ops,
+	.unlock_reg = 0xe6060000, /* PMMR */
+
+	.function = { PINMUX_FUNCTION_BEGIN, PINMUX_FUNCTION_END },
+
+	.pins = pinmux_pins,
+	.nr_pins = ARRAY_SIZE(pinmux_pins),
+	.groups = pinmux_groups.common,
+	.nr_groups = ARRAY_SIZE(pinmux_groups.common),
+	.functions = pinmux_functions.common,
+	.nr_functions = ARRAY_SIZE(pinmux_functions.common),
+
+	.cfg_regs = pinmux_config_regs,
+	.drive_regs = pinmux_drive_regs,
+	.bias_regs = pinmux_bias_regs,
+	.ioctrl_regs = pinmux_ioctrl_regs,
+
+	.pinmux_data = pinmux_data,
+	.pinmux_data_size = ARRAY_SIZE(pinmux_data),
+};
+#endif
+
+#ifdef CONFIG_PINCTRL_PFC_R8A77951
 const struct sh_pfc_soc_info r8a77951_pinmux_info = {
 	.name = "r8a77951_pfc",
 	.ops = &r8a77951_pinmux_ops,
@@ -6229,10 +6273,12 @@ const struct sh_pfc_soc_info r8a77951_pinmux_info = {
 
 	.pins = pinmux_pins,
 	.nr_pins = ARRAY_SIZE(pinmux_pins),
-	.groups = pinmux_groups,
-	.nr_groups = ARRAY_SIZE(pinmux_groups),
-	.functions = pinmux_functions,
-	.nr_functions = ARRAY_SIZE(pinmux_functions),
+	.groups = pinmux_groups.common,
+	.nr_groups = ARRAY_SIZE(pinmux_groups.common) +
+			ARRAY_SIZE(pinmux_groups.automotive),
+	.functions = pinmux_functions.common,
+	.nr_functions = ARRAY_SIZE(pinmux_functions.common) +
+			ARRAY_SIZE(pinmux_functions.automotive),
 
 	.cfg_regs = pinmux_config_regs,
 	.drive_regs = pinmux_drive_regs,
@@ -6242,3 +6288,4 @@ const struct sh_pfc_soc_info r8a77951_pinmux_info = {
 	.pinmux_data = pinmux_data,
 	.pinmux_data_size = ARRAY_SIZE(pinmux_data),
 };
+#endif

drivers/pinctrl/sh-pfc/sh_pfc.h

@@ -312,6 +312,7 @@ extern const struct sh_pfc_soc_info r8a77470_pinmux_info;
 extern const struct sh_pfc_soc_info r8a774a1_pinmux_info;
 extern const struct sh_pfc_soc_info r8a774b1_pinmux_info;
 extern const struct sh_pfc_soc_info r8a774c0_pinmux_info;
+extern const struct sh_pfc_soc_info r8a774e1_pinmux_info;
 extern const struct sh_pfc_soc_info r8a7778_pinmux_info;
 extern const struct sh_pfc_soc_info r8a7779_pinmux_info;
 extern const struct sh_pfc_soc_info r8a7790_pinmux_info;