dt-bindings: leds: convert BCM6328 controller to the json-schema

This helps validating DTS files.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20211114225416.3174-1-zajec5@gmail.comSigned-off-by: Rob Herring <robh@kernel.org>

Documentation/devicetree/bindings/leds/leds-bcm6328.txt

-LEDs connected to Broadcom BCM6328 controller
-
-This controller is present on BCM6318, BCM6328, BCM6362 and BCM63268.
-In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
-However, on some devices there are Serial LEDs (LEDs connected to a 74x164
-controller), which can either be controlled by software (exporting the 74x164
-as spi-gpio. See Documentation/devicetree/bindings/gpio/fairchild,74hc595.yaml),
-or by hardware using this driver.
-Some of these Serial LEDs are hardware controlled (e.g. ethernet LEDs) and
-exporting the 74x164 as spi-gpio prevents those LEDs to be hardware
-controlled, so the only chance to keep them working is by using this driver.
-
-BCM6328 LED controller has a HWDIS register, which controls whether a LED
-should be controlled by a hardware signal instead of the MODE register value,
-with 0 meaning hardware control enabled and 1 hardware control disabled. This
-is usually 1:1 for hardware to LED signals, but through the activity/link
-registers you have some limited control over rerouting the LEDs (as
-explained later in brcm,link-signal-sources). Even if a LED is hardware
-controlled you are still able to make it blink or light it up if it isn't,
-but you can't turn it off if the hardware decides to light it up. For this
-reason, hardware controlled LEDs aren't registered as LED class devices.
-
-Required properties:
-  - compatible : should be "brcm,bcm6328-leds".
-  - #address-cells : must be 1.
-  - #size-cells : must be 0.
-  - reg : BCM6328 LED controller address and size.
-
-Optional properties:
-  - brcm,serial-leds : Boolean, enables Serial LEDs.
-    Default : false
-  - brcm,serial-mux : Boolean, enables Serial LEDs multiplexing.
-    Default : false
-  - brcm,serial-clk-low : Boolean, makes clock signal active low.
-    Default : false
-  - brcm,serial-dat-low : Boolean, makes data signal active low.
-    Default : false
-  - brcm,serial-shift-inv : Boolean, inverts Serial LEDs shift direction.
-    Default : false
-
-Each LED is represented as a sub-node of the brcm,bcm6328-leds device.
-
-LED sub-node required properties:
-  - reg : LED pin number (only LEDs 0 to 23 are valid).
-
-LED sub-node optional properties:
-  a) Optional properties for sub-nodes related to software controlled LEDs:
-    - label : see Documentation/devicetree/bindings/leds/common.txt
-    - active-low : Boolean, makes LED active low.
-      Default : false
-    - default-state : see
-      Documentation/devicetree/bindings/leds/common.txt
-    - linux,default-trigger : see
-      Documentation/devicetree/bindings/leds/common.txt
-
-  b) Optional properties for sub-nodes related to hardware controlled LEDs:
-    - brcm,hardware-controlled : Boolean, makes this LED hardware controlled.
-      Default : false
-    - brcm,link-signal-sources : An array of hardware link
-      signal sources. Up to four link hardware signals can get muxed into
-      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
-      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
-      4 to 7. A signal can be muxed to more than one LED, and one LED can
-      have more than one source signal.
-    - brcm,activity-signal-sources : An array of hardware activity
-      signal sources. Up to four activity hardware signals can get muxed into
-      these LEDs. Only valid for LEDs 0 to 7, where LED signals 0 to 3 may
-      be muxed to LEDs 0 to 3, and signals 4 to 7 may be muxed to LEDs
-      4 to 7. A signal can be muxed to more than one LED, and one LED can
-      have more than one source signal.
-
-Examples:
-Scenario 1 : BCM6328 with 4 EPHY LEDs
-	leds0: led-controller@10000800 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10000800 0x24>;
-
-		alarm_red@2 {
-			reg = <2>;
-			active-low;
-			label = "red:alarm";
-		};
-		inet_green@3 {
-			reg = <3>;
-			active-low;
-			label = "green:inet";
-		};
-		power_green@4 {
-			reg = <4>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-		ephy0_spd@17 {
-			reg = <17>;
-			brcm,hardware-controlled;
-		};
-		ephy1_spd@18 {
-			reg = <18>;
-			brcm,hardware-controlled;
-		};
-		ephy2_spd@19 {
-			reg = <19>;
-			brcm,hardware-controlled;
-		};
-		ephy3_spd@20 {
-			reg = <20>;
-			brcm,hardware-controlled;
-		};
-	};
-
-Scenario 2 : BCM63268 with Serial/GPHY0 LEDs
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-		brcm,serial-leds;
-		brcm,serial-dat-low;
-		brcm,serial-shift-inv;
-
-		gphy0_spd0@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-		};
-		gphy0_spd1@1 {
-			reg = <1>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <1>;
-		};
-		inet_red@2 {
-			reg = <2>;
-			active-low;
-			label = "red:inet";
-		};
-		dsl_green@3 {
-			reg = <3>;
-			active-low;
-			label = "green:dsl";
-		};
-		usb_green@4 {
-			reg = <4>;
-			active-low;
-			label = "green:usb";
-		};
-		wps_green@7 {
-			reg = <7>;
-			active-low;
-			label = "green:wps";
-		};
-		inet_green@8 {
-			reg = <8>;
-			active-low;
-			label = "green:inet";
-		};
-		ephy0_act@9 {
-			reg = <9>;
-			brcm,hardware-controlled;
-		};
-		ephy1_act@10 {
-			reg = <10>;
-			brcm,hardware-controlled;
-		};
-		ephy2_act@11 {
-			reg = <11>;
-			brcm,hardware-controlled;
-		};
-		gphy0_act@12 {
-			reg = <12>;
-			brcm,hardware-controlled;
-		};
-		ephy0_spd@13 {
-			reg = <13>;
-			brcm,hardware-controlled;
-		};
-		ephy1_spd@14 {
-			reg = <14>;
-			brcm,hardware-controlled;
-		};
-		ephy2_spd@15 {
-			reg = <15>;
-			brcm,hardware-controlled;
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 3 : BCM6362 with 1 LED for each EPHY
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-			brcm,activity-signal-sources = <0>;
-			/* USB link/activity routed to USB LED */
-		};
-		inet@1 {
-			reg = <1>;
-			brcm,hardware-controlled;
-			brcm,activity-signal-sources = <1>;
-			/* INET activity routed to INET LED */
-		};
-		ephy0@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4>;
-			/* EPHY0 link routed to EPHY0 LED */
-		};
-		ephy1@5 {
-			reg = <5>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <5>;
-			/* EPHY1 link routed to EPHY1 LED */
-		};
-		ephy2@6 {
-			reg = <6>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <6>;
-			/* EPHY2 link routed to EPHY2 LED */
-		};
-		ephy3@7 {
-			reg = <7>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <7>;
-			/* EPHY3 link routed to EPHY3 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 4 : BCM6362 with 1 LED for all EPHYs
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0 1>;
-			brcm,activity-signal-sources = <0 1>;
-			/* USB/INET link/activity routed to USB LED */
-		};
-		ephy@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4 5 6 7>;
-			/* EPHY0/1/2/3 link routed to EPHY0 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};
-
-Scenario 5 : BCM6362 with EPHY LEDs swapped
-	leds0: led-controller@10001900 {
-		compatible = "brcm,bcm6328-leds";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0x10001900 0x24>;
-
-		usb@0 {
-			reg = <0>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <0>;
-			brcm,activity-signal-sources = <0 1>;
-			/* USB link/act and INET act routed to USB LED */
-		};
-		ephy0@4 {
-			reg = <4>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <7>;
-			/* EPHY3 link routed to EPHY0 LED */
-		};
-		ephy1@5 {
-			reg = <5>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <6>;
-			/* EPHY2 link routed to EPHY1 LED */
-		};
-		ephy2@6 {
-			reg = <6>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <5>;
-			/* EPHY1 link routed to EPHY2 LED */
-		};
-		ephy3@7 {
-			reg = <7>;
-			brcm,hardware-controlled;
-			brcm,link-signal-sources = <4>;
-			/* EPHY0 link routed to EPHY3 LED */
-		};
-		power_green@20 {
-			reg = <20>;
-			active-low;
-			label = "green:power";
-			default-state = "on";
-		};
-	};