powerpc/fsl-booke: Add B4_QDS board support

- Add support for B4 board in board file b4_qds.c,
  It is common for B4860, B4420 and B4220QDS as they share same QDS board
- Add B4QDS support in Kconfig and Makefile

B4860QDS is a high-performance computing evaluation, development and
test platform supporting the B4860 QorIQ Power Architecture processor,
with following major features:

    - Four dual-threaded e6500 Power Architecture processors
      organized in one cluster-each core runs up to 1.8 GHz
    - Two DDR3/3L controllers for high-speed memory interface each
      runs at up to 1866.67 MHz
    - CoreNet fabric that fully supports coherency using MESI protocol
      between the e6500 cores, SC3900 FVP cores, memories and
      external interfaces.
    - Data Path Acceleration Architecture having FMAN, QMan, BMan,
      SEC 5.3 and RMAN
    - Large internal cache memory with snooping and stashing capabilities
    - Sixteen 10-GHz SerDes lanes that serve:
        - Two SRIO interfaces. Each supports up to 4 lanes and
          a total of up to 8 lanes
        - Up to 8-lanes Common Public Radio Interface (CPRI) controller
          for glue-less antenna connection
        - Two 10-Gbit Ethernet controllers (10GEC)
        - Six 1G/2.5-Gbit Ethernet controllers for network communications
        - PCI Express controller
        - Debug (Aurora)
    - Various system peripherals

B4420 and B4220 have some differences in comparison to B4860 with fewer
core/clusters(both SC3900 and e6500), fewer DDR controllers,
fewer serdes lanes, fewer SGMII interfaces and reduced target frequencies.

Key differences between B4860 and B4420:
B4420 has:
    - Fewer e6500 cores:
        1 cluster with 2 e6500 cores
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.6GHz
    - 2 X 4 lane serdes
    - 3 SGMII interfaces
    - no sRIO
    - no 10G

Key differences between B4860 and B4220:
B4220 has:
    - Fewer e6500 cores:
        1 cluster with 1 e6500 core
    - Fewer SC3900 cores/clusters:
        1 cluster with 2 SC3900 cores per cluster
    - Single DDRC @ 1.33GHz
    - 2 X 2 lane serdes
    - 2 SGMII interfaces
    - no sRIO
    - no 10G
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/platforms/85xx/Kconfig

@@ -321,6 +321,23 @@ config T4240_QDS
 	help
 	  This option enables support for the T4240 QDS board
 
+config B4_QDS
+	bool "Freescale B4 QDS"
+	select DEFAULT_UIMAGE
+	select E500
+	select PPC_E500MC
+	select PHYS_64BIT
+	select SWIOTLB
+	select GENERIC_GPIO
+	select ARCH_REQUIRE_GPIOLIB
+	select HAS_RAPIDIO
+	select PPC_EPAPR_HV_PIC
+	help
+	  This option enables support for the B4 QDS board
+	  The B4 application development system B4 QDS is a complete
+	  debugging environment intended for engineers developing
+	  applications for the B4.
+
 endif
 endif # FSL_SOC_BOOKE
 

arch/powerpc/platforms/85xx/Makefile

@@ -23,6 +23,7 @@ obj-$(CONFIG_P4080_DS)    += p4080_ds.o corenet_ds.o
 obj-$(CONFIG_P5020_DS)    += p5020_ds.o corenet_ds.o
 obj-$(CONFIG_P5040_DS)    += p5040_ds.o corenet_ds.o
 obj-$(CONFIG_T4240_QDS)   += t4240_qds.o corenet_ds.o
+obj-$(CONFIG_B4_QDS)	  += b4_qds.o corenet_ds.o
 obj-$(CONFIG_STX_GP3)	  += stx_gp3.o
 obj-$(CONFIG_TQM85xx)	  += tqm85xx.o
 obj-$(CONFIG_SBC8548)     += sbc8548.o

arch/powerpc/platforms/85xx/b4_qds.c

+/*
+ * B4 QDS Setup
+ * Should apply for QDS platform of B4860 and it's personalities.
+ * viz B4860/B4420/B4220QDS
+ *
+ * Copyright 2012 Freescale Semiconductor Inc.
+ *
+ * This program is free software; you can redistribute  it and/or modify it
+ * under  the terms of  the GNU General  Public License as published by the
+ * Free Software Foundation;  either version 2 of the  License, or (at your
+ * option) any later version.
+ */
+
+#include <linux/kernel.h>
+#include <linux/pci.h>
+#include <linux/kdev_t.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/phy.h>
+
+#include <asm/time.h>
+#include <asm/machdep.h>
+#include <asm/pci-bridge.h>
+#include <mm/mmu_decl.h>
+#include <asm/prom.h>
+#include <asm/udbg.h>
+#include <asm/mpic.h>
+
+#include <linux/of_platform.h>
+#include <sysdev/fsl_soc.h>
+#include <sysdev/fsl_pci.h>
+#include <asm/ehv_pic.h>
+
+#include "corenet_ds.h"
+
+/*
+ * Called very early, device-tree isn't unflattened
+ */
+static int __init b4_qds_probe(void)
+{
+	unsigned long root = of_get_flat_dt_root();
+#ifdef CONFIG_SMP
+	extern struct smp_ops_t smp_85xx_ops;
+#endif
+
+	if ((of_flat_dt_is_compatible(root, "fsl,B4860QDS")) ||
+		(of_flat_dt_is_compatible(root, "fsl,B4420QDS")) ||
+			(of_flat_dt_is_compatible(root, "fsl,B4220QDS")))
+		return 1;
+
+	/* Check if we're running under the Freescale hypervisor */
+	if ((of_flat_dt_is_compatible(root, "fsl,B4860QDS-hv")) ||
+		(of_flat_dt_is_compatible(root, "fsl,B4420QDS-hv")) ||
+			(of_flat_dt_is_compatible(root, "fsl,B4220QDS-hv"))) {
+		ppc_md.init_IRQ = ehv_pic_init;
+		ppc_md.get_irq = ehv_pic_get_irq;
+		ppc_md.restart = fsl_hv_restart;
+		ppc_md.power_off = fsl_hv_halt;
+		ppc_md.halt = fsl_hv_halt;
+#ifdef CONFIG_SMP
+		/*
+		 * Disable the timebase sync operations because we can't write
+		 * to the timebase registers under the hypervisor.
+		  */
+		smp_85xx_ops.give_timebase = NULL;
+		smp_85xx_ops.take_timebase = NULL;
+#endif
+		return 1;
+	}
+
+	return 0;
+}
+
+define_machine(b4_qds) {
+	.name			= "B4 QDS",
+	.probe			= b4_qds_probe,
+	.setup_arch		= corenet_ds_setup_arch,
+	.init_IRQ		= corenet_ds_pic_init,
+#ifdef CONFIG_PCI
+	.pcibios_fixup_bus	= fsl_pcibios_fixup_bus,
+#endif
+/* coreint doesn't play nice with lazy EE, use legacy mpic for now */
+#ifdef CONFIG_PPC64
+	.get_irq		= mpic_get_irq,
+#else
+	.get_irq		= mpic_get_coreint_irq,
+#endif
+	.restart		= fsl_rstcr_restart,
+	.calibrate_decr		= generic_calibrate_decr,
+	.progress		= udbg_progress,
+#ifdef CONFIG_PPC64
+	.power_save		= book3e_idle,
+#else
+	.power_save		= e500_idle,
+#endif
+};
+
+machine_arch_initcall(b4_qds, corenet_ds_publish_devices);
+
+#ifdef CONFIG_SWIOTLB
+machine_arch_initcall(b4_qds, swiotlb_setup_bus_notifier);
+#endif