Commit afaa7c54 authored by Chris Zankel's avatar Chris Zankel

Merge tag 'xtensa-for-next-20151109' of git://github.com/jcmvbkbc/linux-xtensa

Xtensa improvements for 4.4:

- fix remaining issues with noMMU cores;
- fix build for cores w/o cache or zero overhead loop options;
- fix boot of secondary cores in SMP configuration;
- add support for DMA to high memory pages;
- add dma_to_phys and phys_to_dma functions.
parents 6a13feb9 4c3dab39
......@@ -17,6 +17,7 @@ config XTENSA
select HAVE_DMA_API_DEBUG
select HAVE_DMA_ATTRS
select HAVE_FUNCTION_TRACER
select HAVE_FUTEX_CMPXCHG if !MMU
select HAVE_IRQ_TIME_ACCOUNTING
select HAVE_OPROFILE
select HAVE_PERF_EVENTS
......@@ -397,6 +398,20 @@ config SIMDISK1_FILENAME
source "mm/Kconfig"
config FORCE_MAX_ZONEORDER
int "Maximum zone order"
default "11"
help
The kernel memory allocator divides physically contiguous memory
blocks into "zones", where each zone is a power of two number of
pages. This option selects the largest power of two that the kernel
keeps in the memory allocator. If you need to allocate very large
blocks of physically contiguous memory, then you may need to
increase this value.
This config option is actually maximum order plus one. For example,
a value of 11 means that the largest free memory block is 2^10 pages.
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
......@@ -408,7 +423,7 @@ config DEFAULT_MEM_START
hex "Physical address of the default memory area start"
depends on PLATFORM_WANT_DEFAULT_MEM
default 0x00000000 if MMU
default 0x40000000 if !MMU
default 0x60000000 if !MMU
help
This is a fallback start address of the default memory area, it is
used when no physical memory size is passed through DTB or through
......
......@@ -40,17 +40,4 @@ SECTIONS
*(.bss)
__bss_end = .;
}
#ifdef CONFIG_MMU
/*
* This is a remapped copy of the Reset Vector Code.
* It keeps gdb in sync with the PC after switching
* to the temporary mapping used while setting up
* the V2 MMU mappings for Linux.
*/
.ResetVector.remapped_text 0x46000000 (INFO):
{
*(.ResetVector.remapped_text)
}
#endif
}
......@@ -58,8 +58,6 @@ _SetupMMU:
wsr a0, ps
rsync
Offset = _SetupMMU - _ResetVector
#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
initialize_mmu
#endif
......@@ -74,29 +72,3 @@ reset:
movi a3, 0
movi a4, 0
jx a0
#ifdef CONFIG_MMU
.align 4
.section .ResetVector.remapped_text, "x"
.global _RemappedResetVector
/* Do org before literals */
.org 0
_RemappedResetVector:
.begin no-absolute-literals
.literal_position
_j _RemappedSetupMMU
/* Position Remapped code at the same location as the original code */
. = _RemappedResetVector + Offset
_RemappedSetupMMU:
#ifndef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
initialize_mmu
#endif
.end no-absolute-literals
#endif
/dts-v1/;
/include/ "xtfpga.dtsi"
/include/ "xtfpga-flash-128m.dtsi"
/ {
compatible = "cdns,xtensa-kc705";
chosen {
bootargs = "earlycon=uart8250,mmio32,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug";
};
memory@0 {
device_type = "memory";
reg = <0x60000000 0x10000000>;
};
soc {
ranges = <0x00000000 0x90000000 0x10000000>;
};
};
CONFIG_SYSVIPC=y
CONFIG_POSIX_MQUEUE=y
CONFIG_FHANDLE=y
CONFIG_IRQ_DOMAIN_DEBUG=y
CONFIG_NO_HZ_IDLE=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_IRQ_TIME_ACCOUNTING=y
CONFIG_BSD_PROCESS_ACCT=y
CONFIG_CGROUP_DEBUG=y
CONFIG_CGROUP_FREEZER=y
CONFIG_CGROUP_DEVICE=y
CONFIG_CPUSETS=y
CONFIG_CGROUP_CPUACCT=y
CONFIG_MEMCG=y
CONFIG_NAMESPACES=y
CONFIG_SCHED_AUTOGROUP=y
CONFIG_RELAY=y
CONFIG_BLK_DEV_INITRD=y
# CONFIG_RD_BZIP2 is not set
# CONFIG_RD_LZMA is not set
# CONFIG_RD_XZ is not set
# CONFIG_RD_LZO is not set
# CONFIG_RD_LZ4 is not set
CONFIG_EXPERT=y
CONFIG_SYSCTL_SYSCALL=y
CONFIG_KALLSYMS_ALL=y
CONFIG_PERF_EVENTS=y
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_IOSCHED_DEADLINE is not set
# CONFIG_IOSCHED_CFQ is not set
CONFIG_XTENSA_VARIANT_CUSTOM=y
CONFIG_XTENSA_VARIANT_CUSTOM_NAME="de212"
# CONFIG_XTENSA_VARIANT_MMU is not set
CONFIG_XTENSA_UNALIGNED_USER=y
CONFIG_PREEMPT=y
# CONFIG_PCI is not set
CONFIG_XTENSA_PLATFORM_XTFPGA=y
CONFIG_CMDLINE_BOOL=y
CONFIG_CMDLINE="earlycon=uart8250,mmio32,0x9d050020,115200n8 console=ttyS0,115200n8 ip=dhcp root=/dev/nfs rw debug"
CONFIG_USE_OF=y
CONFIG_BUILTIN_DTB="kc705_nommu"
CONFIG_DEFAULT_MEM_SIZE=0x10000000
CONFIG_BINFMT_FLAT=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_IP_PNP_RARP=y
# CONFIG_IPV6 is not set
CONFIG_NETFILTER=y
# CONFIG_WIRELESS is not set
CONFIG_DEVTMPFS=y
CONFIG_DEVTMPFS_MOUNT=y
# CONFIG_STANDALONE is not set
CONFIG_MTD=y
CONFIG_MTD_CFI=y
CONFIG_MTD_JEDECPROBE=y
CONFIG_MTD_CFI_INTELEXT=y
CONFIG_MTD_CFI_AMDSTD=y
CONFIG_MTD_CFI_STAA=y
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_SCSI=y
CONFIG_BLK_DEV_SD=y
CONFIG_NETDEVICES=y
# CONFIG_NET_VENDOR_ARC is not set
# CONFIG_NET_VENDOR_BROADCOM is not set
# CONFIG_NET_VENDOR_INTEL is not set
# CONFIG_NET_VENDOR_MARVELL is not set
# CONFIG_NET_VENDOR_MICREL is not set
# CONFIG_NET_VENDOR_NATSEMI is not set
# CONFIG_NET_VENDOR_SEEQ is not set
# CONFIG_NET_VENDOR_STMICRO is not set
# CONFIG_NET_VENDOR_VIA is not set
# CONFIG_NET_VENDOR_WIZNET is not set
CONFIG_MARVELL_PHY=y
# CONFIG_WLAN is not set
# CONFIG_INPUT_MOUSEDEV is not set
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
CONFIG_SERIAL_8250=y
# CONFIG_SERIAL_8250_DEPRECATED_OPTIONS is not set
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_SERIAL_OF_PLATFORM=y
CONFIG_HW_RANDOM=y
# CONFIG_HWMON is not set
CONFIG_WATCHDOG=y
CONFIG_WATCHDOG_NOWAYOUT=y
CONFIG_SOFT_WATCHDOG=y
# CONFIG_VGA_CONSOLE is not set
# CONFIG_USB_SUPPORT is not set
CONFIG_EXT3_FS=y
CONFIG_EXT4_FS=y
CONFIG_FANOTIFY=y
CONFIG_VFAT_FS=y
CONFIG_JFFS2_FS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V4=y
CONFIG_NFS_SWAP=y
CONFIG_ROOT_NFS=y
CONFIG_SUNRPC_DEBUG=y
CONFIG_NLS_CODEPAGE_437=y
CONFIG_NLS_ISO8859_1=y
CONFIG_PRINTK_TIME=y
CONFIG_DYNAMIC_DEBUG=y
CONFIG_DEBUG_INFO=y
# CONFIG_FRAME_POINTER is not set
CONFIG_MAGIC_SYSRQ=y
CONFIG_DEBUG_VM=y
CONFIG_DEBUG_NOMMU_REGIONS=y
CONFIG_DEBUG_SHIRQ=y
CONFIG_LOCKUP_DETECTOR=y
CONFIG_SCHEDSTATS=y
CONFIG_TIMER_STATS=y
CONFIG_DEBUG_RT_MUTEXES=y
CONFIG_DEBUG_SPINLOCK=y
CONFIG_DEBUG_MUTEXES=y
CONFIG_DEBUG_ATOMIC_SLEEP=y
CONFIG_STACKTRACE=y
# CONFIG_RCU_CPU_STALL_INFO is not set
CONFIG_RCU_TRACE=y
# CONFIG_FTRACE is not set
# CONFIG_LD_NO_RELAX is not set
# CONFIG_CRYPTO_ECHAINIV is not set
CONFIG_CRYPTO_ANSI_CPRNG=y
......@@ -35,9 +35,10 @@
* __loop as
* restart loop. 'as' register must not have been modified!
*
* __endla ar, at, incr
* __endla ar, as, incr
* ar start address (modified)
* as scratch register used by macro
* as scratch register used by __loops/__loopi macros or
* end address used by __loopt macro
* inc increment
*/
......@@ -97,7 +98,7 @@
.endm
/*
* loop from ar to ax
* loop from ar to as
*/
.macro __loopt ar, as, at, incr_log2
......
......@@ -73,7 +73,9 @@
.macro ___unlock_dcache_all ar at
#if XCHAL_DCACHE_SIZE
__loop_cache_all \ar \at diu XCHAL_DCACHE_SIZE XCHAL_DCACHE_LINEWIDTH
#endif
.endm
......@@ -90,30 +92,38 @@
.macro ___flush_invalidate_dcache_all ar at
#if XCHAL_DCACHE_SIZE
__loop_cache_all \ar \at diwbi XCHAL_DCACHE_SIZE XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___flush_dcache_all ar at
#if XCHAL_DCACHE_SIZE
__loop_cache_all \ar \at diwb XCHAL_DCACHE_SIZE XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_dcache_all ar at
#if XCHAL_DCACHE_SIZE
__loop_cache_all \ar \at dii __stringify(DCACHE_WAY_SIZE) \
XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_icache_all ar at
#if XCHAL_ICACHE_SIZE
__loop_cache_all \ar \at iii __stringify(ICACHE_WAY_SIZE) \
XCHAL_ICACHE_LINEWIDTH
#endif
.endm
......@@ -121,28 +131,36 @@
.macro ___flush_invalidate_dcache_range ar as at
#if XCHAL_DCACHE_SIZE
__loop_cache_range \ar \as \at dhwbi XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___flush_dcache_range ar as at
#if XCHAL_DCACHE_SIZE
__loop_cache_range \ar \as \at dhwb XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_dcache_range ar as at
#if XCHAL_DCACHE_SIZE
__loop_cache_range \ar \as \at dhi XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_icache_range ar as at
#if XCHAL_ICACHE_SIZE
__loop_cache_range \ar \as \at ihi XCHAL_ICACHE_LINEWIDTH
#endif
.endm
......@@ -150,27 +168,35 @@
.macro ___flush_invalidate_dcache_page ar as
#if XCHAL_DCACHE_SIZE
__loop_cache_page \ar \as dhwbi XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___flush_dcache_page ar as
#if XCHAL_DCACHE_SIZE
__loop_cache_page \ar \as dhwb XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_dcache_page ar as
#if XCHAL_DCACHE_SIZE
__loop_cache_page \ar \as dhi XCHAL_DCACHE_LINEWIDTH
#endif
.endm
.macro ___invalidate_icache_page ar as
#if XCHAL_ICACHE_SIZE
__loop_cache_page \ar \as ihi XCHAL_ICACHE_LINEWIDTH
#endif
.endm
......@@ -55,9 +55,14 @@ extern void __flush_dcache_range(unsigned long, unsigned long);
extern void __flush_invalidate_dcache_page(unsigned long);
extern void __flush_invalidate_dcache_range(unsigned long, unsigned long);
#else
# define __flush_dcache_range(p,s) do { } while(0)
# define __flush_dcache_page(p) do { } while(0)
# define __flush_invalidate_dcache_page(p) __invalidate_dcache_page(p)
static inline void __flush_dcache_page(unsigned long va)
{
}
static inline void __flush_dcache_range(unsigned long va, unsigned long sz)
{
}
# define __flush_invalidate_dcache_all() __invalidate_dcache_all()
# define __flush_invalidate_dcache_page(p) __invalidate_dcache_page(p)
# define __flush_invalidate_dcache_range(p,s) __invalidate_dcache_range(p,s)
#endif
......@@ -174,99 +179,4 @@ extern void copy_from_user_page(struct vm_area_struct*, struct page*,
#endif
#define XTENSA_CACHEBLK_LOG2 29
#define XTENSA_CACHEBLK_SIZE (1 << XTENSA_CACHEBLK_LOG2)
#define XTENSA_CACHEBLK_MASK (7 << XTENSA_CACHEBLK_LOG2)
#if XCHAL_HAVE_CACHEATTR
static inline u32 xtensa_get_cacheattr(void)
{
u32 r;
asm volatile(" rsr %0, cacheattr" : "=a"(r));
return r;
}
static inline u32 xtensa_get_dtlb1(u32 addr)
{
u32 r = addr & XTENSA_CACHEBLK_MASK;
return r | ((xtensa_get_cacheattr() >> (r >> (XTENSA_CACHEBLK_LOG2-2)))
& 0xF);
}
#else
static inline u32 xtensa_get_dtlb1(u32 addr)
{
u32 r;
asm volatile(" rdtlb1 %0, %1" : "=a"(r) : "a"(addr));
asm volatile(" dsync");
return r;
}
static inline u32 xtensa_get_cacheattr(void)
{
u32 r = 0;
u32 a = 0;
do {
a -= XTENSA_CACHEBLK_SIZE;
r = (r << 4) | (xtensa_get_dtlb1(a) & 0xF);
} while (a);
return r;
}
#endif
static inline int xtensa_need_flush_dma_source(u32 addr)
{
return (xtensa_get_dtlb1(addr) & ((1 << XCHAL_CA_BITS) - 1)) >= 4;
}
static inline int xtensa_need_invalidate_dma_destination(u32 addr)
{
return (xtensa_get_dtlb1(addr) & ((1 << XCHAL_CA_BITS) - 1)) != 2;
}
static inline void flush_dcache_unaligned(u32 addr, u32 size)
{
u32 cnt;
if (size) {
cnt = (size + ((XCHAL_DCACHE_LINESIZE - 1) & addr)
+ XCHAL_DCACHE_LINESIZE - 1) / XCHAL_DCACHE_LINESIZE;
while (cnt--) {
asm volatile(" dhwb %0, 0" : : "a"(addr));
addr += XCHAL_DCACHE_LINESIZE;
}
asm volatile(" dsync");
}
}
static inline void invalidate_dcache_unaligned(u32 addr, u32 size)
{
int cnt;
if (size) {
asm volatile(" dhwbi %0, 0 ;" : : "a"(addr));
cnt = (size + ((XCHAL_DCACHE_LINESIZE - 1) & addr)
- XCHAL_DCACHE_LINESIZE - 1) / XCHAL_DCACHE_LINESIZE;
while (cnt-- > 0) {
asm volatile(" dhi %0, %1" : : "a"(addr),
"n"(XCHAL_DCACHE_LINESIZE));
addr += XCHAL_DCACHE_LINESIZE;
}
asm volatile(" dhwbi %0, %1" : : "a"(addr),
"n"(XCHAL_DCACHE_LINESIZE));
asm volatile(" dsync");
}
}
static inline void flush_invalidate_dcache_unaligned(u32 addr, u32 size)
{
u32 cnt;
if (size) {
cnt = (size + ((XCHAL_DCACHE_LINESIZE - 1) & addr)
+ XCHAL_DCACHE_LINESIZE - 1) / XCHAL_DCACHE_LINESIZE;
while (cnt--) {
asm volatile(" dhwbi %0, 0" : : "a"(addr));
addr += XCHAL_DCACHE_LINESIZE;
}
asm volatile(" dsync");
}
}
#endif /* _XTENSA_CACHEFLUSH_H */
......@@ -35,4 +35,14 @@ static inline struct dma_map_ops *get_dma_ops(struct device *dev)
void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
enum dma_data_direction direction);
static inline dma_addr_t phys_to_dma(struct device *dev, phys_addr_t paddr)
{
return (dma_addr_t)paddr;
}
static inline phys_addr_t dma_to_phys(struct device *dev, dma_addr_t daddr)
{
return (phys_addr_t)daddr;
}
#endif /* _XTENSA_DMA_MAPPING_H */
......@@ -161,7 +161,8 @@
#endif /* defined(CONFIG_MMU) && XCHAL_HAVE_PTP_MMU &&
XCHAL_HAVE_SPANNING_WAY */
#if !defined(CONFIG_MMU) && XCHAL_HAVE_TLBS
#if !defined(CONFIG_MMU) && XCHAL_HAVE_TLBS && \
(XCHAL_DCACHE_SIZE || XCHAL_ICACHE_SIZE)
/* Enable data and instruction cache in the DEFAULT_MEMORY region
* if the processor has DTLB and ITLB.
*/
......@@ -175,14 +176,18 @@
1:
sub a9, a9, a8
2:
#if XCHAL_DCACHE_SIZE
rdtlb1 a3, a5
ritlb1 a4, a5
and a3, a3, a6
and a4, a4, a6
or a3, a3, a7
or a4, a4, a7
wdtlb a3, a5
#endif
#if XCHAL_ICACHE_SIZE
ritlb1 a4, a5
and a4, a4, a6
or a4, a4, a7
witlb a4, a5
#endif
add a5, a5, a8
bltu a8, a9, 1b
......
......@@ -25,15 +25,6 @@
#ifdef CONFIG_MMU
#if XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY && defined(CONFIG_OF)
extern unsigned long xtensa_kio_paddr;
static inline unsigned long xtensa_get_kio_paddr(void)
{
return xtensa_kio_paddr;
}
#endif
/*
* Return the virtual address for the specified bus memory.
* Note that we currently don't support any address outside the KIO segment.
......
......@@ -18,7 +18,11 @@
* We only use two ring levels, user and kernel space.
*/
#ifdef CONFIG_MMU
#define USER_RING 1 /* user ring level */
#else
#define USER_RING 0
#endif
#define KERNEL_RING 0 /* kernel ring level */
/*
......
......@@ -21,13 +21,26 @@
#include <variant/core.h>
#include <platform/hardware.h>
#if XCHAL_HAVE_PTP_MMU
#define XCHAL_KIO_CACHED_VADDR 0xe0000000
#define XCHAL_KIO_BYPASS_VADDR 0xf0000000
#define XCHAL_KIO_DEFAULT_PADDR 0xf0000000
#else
#define XCHAL_KIO_BYPASS_VADDR XCHAL_KIO_PADDR
#define XCHAL_KIO_DEFAULT_PADDR 0x90000000
#endif
#define XCHAL_KIO_SIZE 0x10000000
#if XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY && defined(CONFIG_OF)
#if (!XCHAL_HAVE_PTP_MMU || XCHAL_HAVE_SPANNING_WAY) && defined(CONFIG_OF)
#define XCHAL_KIO_PADDR xtensa_get_kio_paddr()
#ifndef __ASSEMBLY__
extern unsigned long xtensa_kio_paddr;
static inline unsigned long xtensa_get_kio_paddr(void)
{
return xtensa_kio_paddr;
}
#endif
#else
#define XCHAL_KIO_PADDR XCHAL_KIO_DEFAULT_PADDR
#endif
......@@ -48,6 +61,9 @@
#define LOAD_MEMORY_ADDRESS 0xD0003000
#endif
#define RESET_VECTOR1_VADDR (VIRTUAL_MEMORY_ADDRESS + \
XCHAL_RESET_VECTOR1_PADDR)
#else /* !defined(CONFIG_MMU) */
/* MMU Not being used - Virtual == Physical */
......@@ -60,6 +76,8 @@
/* Loaded just above possibly live vectors */
#define LOAD_MEMORY_ADDRESS (PLATFORM_DEFAULT_MEM_START + 0x3000)
#define RESET_VECTOR1_VADDR (XCHAL_RESET_VECTOR1_VADDR)
#endif /* CONFIG_MMU */
#define XC_VADDR(offset) (VIRTUAL_MEMORY_ADDRESS + offset)
......@@ -67,14 +85,6 @@
/* Used to set VECBASE register */
#define VECBASE_RESET_VADDR VIRTUAL_MEMORY_ADDRESS
#define RESET_VECTOR_VECOFS (XCHAL_RESET_VECTOR_VADDR - \
VECBASE_RESET_VADDR)
#define RESET_VECTOR_VADDR XC_VADDR(RESET_VECTOR_VECOFS)
#define RESET_VECTOR1_VECOFS (XCHAL_RESET_VECTOR1_VADDR - \
VECBASE_RESET_VADDR)
#define RESET_VECTOR1_VADDR XC_VADDR(RESET_VECTOR1_VECOFS)
#if defined(XCHAL_HAVE_VECBASE) && XCHAL_HAVE_VECBASE
#define USER_VECTOR_VADDR XC_VADDR(XCHAL_USER_VECOFS)
......
......@@ -16,6 +16,7 @@ obj-$(CONFIG_SMP) += smp.o mxhead.o
obj-$(CONFIG_XTENSA_VARIANT_HAVE_PERF_EVENTS) += perf_event.o
AFLAGS_head.o += -mtext-section-literals
AFLAGS_mxhead.o += -mtext-section-literals
# In the Xtensa architecture, assembly generates literals which must always
# precede the L32R instruction with a relative offset less than 256 kB.
......
......@@ -367,8 +367,10 @@ common_exception:
s32i a2, a1, PT_SYSCALL
movi a2, 0
s32i a3, a1, PT_EXCVADDR
#if XCHAL_HAVE_LOOPS
xsr a2, lcount
s32i a2, a1, PT_LCOUNT
#endif
/* It is now save to restore the EXC_TABLE_FIXUP variable. */
......@@ -429,11 +431,12 @@ common_exception:
rsync # PS.WOE => rsync => overflow
/* Save lbeg, lend */
#if XCHAL_HAVE_LOOPS
rsr a4, lbeg
rsr a3, lend
s32i a4, a1, PT_LBEG
s32i a3, a1, PT_LEND
#endif
/* Save SCOMPARE1 */
......@@ -724,13 +727,14 @@ common_exception_exit:
wsr a3, sar
/* Restore LBEG, LEND, LCOUNT */
#if XCHAL_HAVE_LOOPS
l32i a2, a1, PT_LBEG
l32i a3, a1, PT_LEND
wsr a2, lbeg
l32i a2, a1, PT_LCOUNT
wsr a3, lend
wsr a2, lcount
#endif
/* We control single stepping through the ICOUNTLEVEL register. */
......
......@@ -249,7 +249,7 @@ ENTRY(_startup)
__loopt a2, a3, a4, 2
s32i a0, a2, 0
__endla a2, a4, 4
__endla a2, a3, 4
#if XCHAL_DCACHE_IS_WRITEBACK
......
......@@ -48,8 +48,6 @@ _SetupOCD:
rsync
_SetupMMU:
Offset = _SetupMMU - _SecondaryResetVector
#ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
initialize_mmu
#endif
......@@ -62,24 +60,3 @@ _SetupMMU:
jx a3
.end no-absolute-literals
.section .SecondaryResetVector.remapped_text, "ax"
.global _RemappedSecondaryResetVector
.org 0 # Need to do org before literals
_RemappedSecondaryResetVector:
.begin no-absolute-literals
.literal_position
_j _RemappedSetupMMU
. = _RemappedSecondaryResetVector + Offset
_RemappedSetupMMU:
#ifdef CONFIG_INITIALIZE_XTENSA_MMU_INSIDE_VMLINUX
initialize_mmu
#endif
.end no-absolute-literals
......@@ -15,14 +15,15 @@
* Joe Taylor <joe@tensilica.com, joetylr@yahoo.com>
*/
#include <linux/types.h>
#include <linux/mm.h>
#include <linux/string.h>
#include <linux/pci.h>
#include <linux/gfp.h>
#include <linux/highmem.h>
#include <linux/mm.h>
#include <linux/module.h>
#include <asm/io.h>
#include <linux/pci.h>
#include <linux/string.h>
#include <linux/types.h>
#include <asm/cacheflush.h>
#include <asm/io.h>
void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
enum dma_data_direction dir)
......@@ -47,17 +48,36 @@ void dma_cache_sync(struct device *dev, void *vaddr, size_t size,
}
EXPORT_SYMBOL(dma_cache_sync);
static void do_cache_op(dma_addr_t dma_handle, size_t size,
void (*fn)(unsigned long, unsigned long))
{
unsigned long off = dma_handle & (PAGE_SIZE - 1);
unsigned long pfn = PFN_DOWN(dma_handle);
struct page *page = pfn_to_page(pfn);
if (!PageHighMem(page))
fn((unsigned long)bus_to_virt(dma_handle), size);
else
while (size > 0) {
size_t sz = min_t(size_t, size, PAGE_SIZE - off);
void *vaddr = kmap_atomic(page);
fn((unsigned long)vaddr + off, sz);
kunmap_atomic(vaddr);
off = 0;
++page;
size -= sz;
}
}
static void xtensa_sync_single_for_cpu(struct device *dev,
dma_addr_t dma_handle, size_t size,
enum dma_data_direction dir)
{
void *vaddr;
switch (dir) {
case DMA_BIDIRECTIONAL:
case DMA_FROM_DEVICE:
vaddr = bus_to_virt(dma_handle);
__invalidate_dcache_range((unsigned long)vaddr, size);
do_cache_op(dma_handle, size, __invalidate_dcache_range);
break;
case DMA_NONE:
......@@ -73,13 +93,11 @@ static void xtensa_sync_single_for_device(struct device *dev,
dma_addr_t dma_handle, size_t size,
enum dma_data_direction dir)
{
void *vaddr;
switch (dir) {
case DMA_BIDIRECTIONAL:
case DMA_TO_DEVICE:
vaddr = bus_to_virt(dma_handle);
__flush_dcache_range((unsigned long)vaddr, size);
if (XCHAL_DCACHE_IS_WRITEBACK)
do_cache_op(dma_handle, size, __flush_dcache_range);
break;
case DMA_NONE:
......@@ -171,7 +189,6 @@ static dma_addr_t xtensa_map_page(struct device *dev, struct page *page,
{
dma_addr_t dma_handle = page_to_phys(page) + offset;
BUG_ON(PageHighMem(page));
xtensa_sync_single_for_device(dev, dma_handle, size, dir);
return dma_handle;
}
......
......@@ -190,7 +190,7 @@ static int __init parse_bootparam(const bp_tag_t* tag)
#ifdef CONFIG_OF
bool __initdata dt_memory_scan = false;
#if XCHAL_HAVE_PTP_MMU && XCHAL_HAVE_SPANNING_WAY
#if !XCHAL_HAVE_PTP_MMU || XCHAL_HAVE_SPANNING_WAY
unsigned long xtensa_kio_paddr = XCHAL_KIO_DEFAULT_PADDR;
EXPORT_SYMBOL(xtensa_kio_paddr);
......@@ -334,7 +334,10 @@ extern char _Level5InterruptVector_text_end;
extern char _Level6InterruptVector_text_start;
extern char _Level6InterruptVector_text_end;
#endif
#ifdef CONFIG_SMP
extern char _SecondaryResetVector_text_start;
extern char _SecondaryResetVector_text_end;
#endif
#ifdef CONFIG_S32C1I_SELFTEST
......@@ -506,6 +509,10 @@ void __init setup_arch(char **cmdline_p)
__pa(&_Level6InterruptVector_text_end), 0);
#endif
#ifdef CONFIG_SMP
mem_reserve(__pa(&_SecondaryResetVector_text_start),
__pa(&_SecondaryResetVector_text_end), 0);
#endif
parse_early_param();
bootmem_init();
......
......@@ -478,6 +478,9 @@ _DoubleExceptionVector_handle_exception:
ENDPROC(_DoubleExceptionVector)
.end literal_prefix
.text
/*
* Fixup handler for TLB miss in double exception handler for window owerflow.
* We get here with windowbase set to the window that was being spilled and
......@@ -587,7 +590,6 @@ ENTRY(window_overflow_restore_a0_fixup)
ENDPROC(window_overflow_restore_a0_fixup)
.end literal_prefix
/*
* Debug interrupt vector
*
......
......@@ -166,8 +166,6 @@ SECTIONS
RELOCATE_ENTRY(_DebugInterruptVector_text,
.DebugInterruptVector.text);
#if defined(CONFIG_SMP)
RELOCATE_ENTRY(_SecondaryResetVector_literal,
.SecondaryResetVector.literal);
RELOCATE_ENTRY(_SecondaryResetVector_text,
.SecondaryResetVector.text);
#endif
......@@ -282,17 +280,11 @@ SECTIONS
#if defined(CONFIG_SMP)
SECTION_VECTOR (_SecondaryResetVector_literal,
.SecondaryResetVector.literal,
RESET_VECTOR1_VADDR - 4,
SIZEOF(.DoubleExceptionVector.text),
.DoubleExceptionVector.text)
SECTION_VECTOR (_SecondaryResetVector_text,
.SecondaryResetVector.text,
RESET_VECTOR1_VADDR,
4,
.SecondaryResetVector.literal)
SIZEOF(.DoubleExceptionVector.text),
.DoubleExceptionVector.text)
. = LOADADDR(.SecondaryResetVector.text)+SIZEOF(.SecondaryResetVector.text);
......@@ -306,31 +298,6 @@ SECTIONS
_end = .;
/* only used by the boot loader */
. = ALIGN(0x10);
.bootstrap : { *(.bootstrap.literal .bootstrap.text .bootstrap.data) }
.ResetVector.text RESET_VECTOR_VADDR :
{
*(.ResetVector.text)
}
/*
* This is a remapped copy of the Secondary Reset Vector Code.
* It keeps gdb in sync with the PC after switching
* to the temporary mapping used while setting up
* the V2 MMU mappings for Linux.
*
* Only debug information about this section is put in the kernel image.
*/
.SecondaryResetVector.remapped_text 0x46000000 (INFO):
{
*(.SecondaryResetVector.remapped_text)
}
.xt.lit : { *(.xt.lit) }
.xt.prop : { *(.xt.prop) }
......
......@@ -222,8 +222,8 @@ __xtensa_copy_user:
loopnez a7, .Loop2done
#else /* !XCHAL_HAVE_LOOPS */
beqz a7, .Loop2done
slli a10, a7, 4
add a10, a10, a3 # a10 = end of last 16B source chunk
slli a12, a7, 4
add a12, a12, a3 # a12 = end of last 16B source chunk
#endif /* !XCHAL_HAVE_LOOPS */
.Loop2:
EX(l32i, a7, a3, 4, l_fixup)
......@@ -241,7 +241,7 @@ __xtensa_copy_user:
EX(s32i, a9, a5, 12, s_fixup)
addi a5, a5, 16
#if !XCHAL_HAVE_LOOPS
blt a3, a10, .Loop2
blt a3, a12, .Loop2
#endif /* !XCHAL_HAVE_LOOPS */
.Loop2done:
bbci.l a4, 3, .L12
......
......@@ -61,7 +61,9 @@ void platform_restart(void)
#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
#endif
#if XCHAL_HAVE_LOOPS
"wsr a2, lcount\n\t"
#endif
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
"isync\n\t"
......
......@@ -72,7 +72,9 @@ void platform_restart(void)
#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
#endif
#if XCHAL_HAVE_LOOPS
"wsr a2, lcount\n\t"
#endif
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
"isync\n\t"
......
......@@ -12,13 +12,15 @@
* This file contains the hardware configuration of the XTAVNET boards.
*/
#include <asm/types.h>
#ifndef __XTENSA_XTAVNET_HARDWARE_H
#define __XTENSA_XTAVNET_HARDWARE_H
/* Memory configuration. */
#define PLATFORM_DEFAULT_MEM_START CONFIG_DEFAULT_MEM_START
#define PLATFORM_DEFAULT_MEM_SIZE CONFIG_DEFAULT_MEM_SIZE
#define PLATFORM_DEFAULT_MEM_START __XTENSA_UL(CONFIG_DEFAULT_MEM_START)
#define PLATFORM_DEFAULT_MEM_SIZE __XTENSA_UL(CONFIG_DEFAULT_MEM_SIZE)
/* Interrupt configuration. */
......
......@@ -63,7 +63,9 @@ void platform_restart(void)
#if XCHAL_NUM_IBREAK > 0
"wsr a2, ibreakenable\n\t"
#endif
#if XCHAL_HAVE_LOOPS
"wsr a2, lcount\n\t"
#endif
"movi a2, 0x1f\n\t"
"wsr a2, ps\n\t"
"isync\n\t"
......
/*
* xtensa/config/core-isa.h -- HAL definitions that are dependent on Xtensa
* processor CORE configuration
*
* See <xtensa/config/core.h>, which includes this file, for more details.
*/
/* Xtensa processor core configuration information.
Copyright (c) 1999-2015 Tensilica Inc.
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
"Software"), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to
the following conditions:
The above copyright notice and this permission notice shall be included
in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */
#ifndef _XTENSA_CORE_CONFIGURATION_H
#define _XTENSA_CORE_CONFIGURATION_H
/****************************************************************************
Parameters Useful for Any Code, USER or PRIVILEGED
****************************************************************************/
/*
* Note: Macros of the form XCHAL_HAVE_*** have a value of 1 if the option is
* configured, and a value of 0 otherwise. These macros are always defined.
*/
/*----------------------------------------------------------------------
ISA
----------------------------------------------------------------------*/
#define XCHAL_HAVE_BE 0 /* big-endian byte ordering */
#define XCHAL_HAVE_WINDOWED 1 /* windowed registers option */
#define XCHAL_NUM_AREGS 32 /* num of physical addr regs */
#define XCHAL_NUM_AREGS_LOG2 5 /* log2(XCHAL_NUM_AREGS) */
#define XCHAL_MAX_INSTRUCTION_SIZE 3 /* max instr bytes (3..8) */
#define XCHAL_HAVE_DEBUG 1 /* debug option */
#define XCHAL_HAVE_DENSITY 1 /* 16-bit instructions */
#define XCHAL_HAVE_LOOPS 1 /* zero-overhead loops */
#define XCHAL_LOOP_BUFFER_SIZE 0 /* zero-ov. loop instr buffer size */
#define XCHAL_HAVE_NSA 1 /* NSA/NSAU instructions */
#define XCHAL_HAVE_MINMAX 1 /* MIN/MAX instructions */
#define XCHAL_HAVE_SEXT 1 /* SEXT instruction */
#define XCHAL_HAVE_DEPBITS 0 /* DEPBITS instruction */
#define XCHAL_HAVE_CLAMPS 1 /* CLAMPS instruction */
#define XCHAL_HAVE_MUL16 1 /* MUL16S/MUL16U instructions */
#define XCHAL_HAVE_MUL32 1 /* MULL instruction */
#define XCHAL_HAVE_MUL32_HIGH 0 /* MULUH/MULSH instructions */
#define XCHAL_HAVE_DIV32 1 /* QUOS/QUOU/REMS/REMU instructions */
#define XCHAL_HAVE_L32R 1 /* L32R instruction */
#define XCHAL_HAVE_ABSOLUTE_LITERALS 0 /* non-PC-rel (extended) L32R */
#define XCHAL_HAVE_CONST16 0 /* CONST16 instruction */
#define XCHAL_HAVE_ADDX 1 /* ADDX#/SUBX# instructions */
#define XCHAL_HAVE_WIDE_BRANCHES 0 /* B*.W18 or B*.W15 instr's */
#define XCHAL_HAVE_PREDICTED_BRANCHES 0 /* B[EQ/EQZ/NE/NEZ]T instr's */
#define XCHAL_HAVE_CALL4AND12 1 /* (obsolete option) */
#define XCHAL_HAVE_ABS 1 /* ABS instruction */
/*#define XCHAL_HAVE_POPC 0*/ /* POPC instruction */
/*#define XCHAL_HAVE_CRC 0*/ /* CRC instruction */
#define XCHAL_HAVE_RELEASE_SYNC 1 /* L32AI/S32RI instructions */
#define XCHAL_HAVE_S32C1I 1 /* S32C1I instruction */
#define XCHAL_HAVE_SPECULATION 0 /* speculation */
#define XCHAL_HAVE_FULL_RESET 1 /* all regs/state reset */
#define XCHAL_NUM_CONTEXTS 1 /* */
#define XCHAL_NUM_MISC_REGS 2 /* num of scratch regs (0..4) */
#define XCHAL_HAVE_TAP_MASTER 0 /* JTAG TAP control instr's */
#define XCHAL_HAVE_PRID 1 /* processor ID register */
#define XCHAL_HAVE_EXTERN_REGS 1 /* WER/RER instructions */
#define XCHAL_HAVE_MX 0 /* MX core (Tensilica internal) */
#define XCHAL_HAVE_MP_INTERRUPTS 0 /* interrupt distributor port */
#define XCHAL_HAVE_MP_RUNSTALL 0 /* core RunStall control port */
#define XCHAL_HAVE_PSO 0 /* Power Shut-Off */
#define XCHAL_HAVE_PSO_CDM 0 /* core/debug/mem pwr domains */
#define XCHAL_HAVE_PSO_FULL_RETENTION 0 /* all regs preserved on PSO */
#define XCHAL_HAVE_THREADPTR 0 /* THREADPTR register */
#define XCHAL_HAVE_BOOLEANS 0 /* boolean registers */
#define XCHAL_HAVE_CP 0 /* CPENABLE reg (coprocessor) */
#define XCHAL_CP_MAXCFG 0 /* max allowed cp id plus one */
#define XCHAL_HAVE_MAC16 1 /* MAC16 package */
#define XCHAL_HAVE_FUSION 0 /* Fusion*/
#define XCHAL_HAVE_FUSION_FP 0 /* Fusion FP option */
#define XCHAL_HAVE_FUSION_LOW_POWER 0 /* Fusion Low Power option */
#define XCHAL_HAVE_FUSION_AES 0 /* Fusion BLE/Wifi AES-128 CCM option */
#define XCHAL_HAVE_FUSION_CONVENC 0 /* Fusion Conv Encode option */
#define XCHAL_HAVE_FUSION_LFSR_CRC 0 /* Fusion LFSR-CRC option */
#define XCHAL_HAVE_FUSION_BITOPS 0 /* Fusion Bit Operations Support option */
#define XCHAL_HAVE_FUSION_AVS 0 /* Fusion AVS option */
#define XCHAL_HAVE_FUSION_16BIT_BASEBAND 0 /* Fusion 16-bit Baseband option */
#define XCHAL_HAVE_HIFIPRO 0 /* HiFiPro Audio Engine pkg */
#define XCHAL_HAVE_HIFI4 0 /* HiFi4 Audio Engine pkg */
#define XCHAL_HAVE_HIFI4_VFPU 0 /* HiFi4 Audio Engine VFPU option */
#define XCHAL_HAVE_HIFI3 0 /* HiFi3 Audio Engine pkg */
#define XCHAL_HAVE_HIFI3_VFPU 0 /* HiFi3 Audio Engine VFPU option */
#define XCHAL_HAVE_HIFI2 0 /* HiFi2 Audio Engine pkg */
#define XCHAL_HAVE_HIFI2EP 0 /* HiFi2EP */
#define XCHAL_HAVE_HIFI_MINI 0
#define XCHAL_HAVE_VECTORFPU2005 0 /* vector or user floating-point pkg */
#define XCHAL_HAVE_USER_DPFPU 0 /* user DP floating-point pkg */
#define XCHAL_HAVE_USER_SPFPU 0 /* user DP floating-point pkg */
#define XCHAL_HAVE_FP 0 /* single prec floating point */
#define XCHAL_HAVE_FP_DIV 0 /* FP with DIV instructions */
#define XCHAL_HAVE_FP_RECIP 0 /* FP with RECIP instructions */
#define XCHAL_HAVE_FP_SQRT 0 /* FP with SQRT instructions */
#define XCHAL_HAVE_FP_RSQRT 0 /* FP with RSQRT instructions */
#define XCHAL_HAVE_DFP 0 /* double precision FP pkg */
#define XCHAL_HAVE_DFP_DIV 0 /* DFP with DIV instructions */
#define XCHAL_HAVE_DFP_RECIP 0 /* DFP with RECIP instructions*/
#define XCHAL_HAVE_DFP_SQRT 0 /* DFP with SQRT instructions */
#define XCHAL_HAVE_DFP_RSQRT 0 /* DFP with RSQRT instructions*/
#define XCHAL_HAVE_DFP_ACCEL 0 /* double precision FP acceleration pkg */
#define XCHAL_HAVE_DFP_accel XCHAL_HAVE_DFP_ACCEL /* for backward compatibility */
#define XCHAL_HAVE_DFPU_SINGLE_ONLY 0 /* DFPU Coprocessor, single precision only */
#define XCHAL_HAVE_DFPU_SINGLE_DOUBLE 0 /* DFPU Coprocessor, single and double precision */
#define XCHAL_HAVE_VECTRA1 0 /* Vectra I pkg */
#define XCHAL_HAVE_VECTRALX 0 /* Vectra LX pkg */
#define XCHAL_HAVE_PDX4 0 /* PDX4 */
#define XCHAL_HAVE_CONNXD2 0 /* ConnX D2 pkg */
#define XCHAL_HAVE_CONNXD2_DUALLSFLIX 0 /* ConnX D2 & Dual LoadStore Flix */
#define XCHAL_HAVE_BBE16 0 /* ConnX BBE16 pkg */
#define XCHAL_HAVE_BBE16_RSQRT 0 /* BBE16 & vector recip sqrt */
#define XCHAL_HAVE_BBE16_VECDIV 0 /* BBE16 & vector divide */
#define XCHAL_HAVE_BBE16_DESPREAD 0 /* BBE16 & despread */
#define XCHAL_HAVE_BBENEP 0 /* ConnX BBENEP pkgs */
#define XCHAL_HAVE_BSP3 0 /* ConnX BSP3 pkg */
#define XCHAL_HAVE_BSP3_TRANSPOSE 0 /* BSP3 & transpose32x32 */
#define XCHAL_HAVE_SSP16 0 /* ConnX SSP16 pkg */
#define XCHAL_HAVE_SSP16_VITERBI 0 /* SSP16 & viterbi */
#define XCHAL_HAVE_TURBO16 0 /* ConnX Turbo16 pkg */
#define XCHAL_HAVE_BBP16 0 /* ConnX BBP16 pkg */
#define XCHAL_HAVE_FLIX3 0 /* basic 3-way FLIX option */
#define XCHAL_HAVE_GRIVPEP 0 /* GRIVPEP is General Release of IVPEP */
#define XCHAL_HAVE_GRIVPEP_HISTOGRAM 0 /* Histogram option on GRIVPEP */
/*----------------------------------------------------------------------
MISC
----------------------------------------------------------------------*/
#define XCHAL_NUM_LOADSTORE_UNITS 1 /* load/store units */
#define XCHAL_NUM_WRITEBUFFER_ENTRIES 8 /* size of write buffer */
#define XCHAL_INST_FETCH_WIDTH 4 /* instr-fetch width in bytes */
#define XCHAL_DATA_WIDTH 4 /* data width in bytes */
#define XCHAL_DATA_PIPE_DELAY 1 /* d-side pipeline delay
(1 = 5-stage, 2 = 7-stage) */
#define XCHAL_CLOCK_GATING_GLOBAL 0 /* global clock gating */
#define XCHAL_CLOCK_GATING_FUNCUNIT 0 /* funct. unit clock gating */
/* In T1050, applies to selected core load and store instructions (see ISA): */
#define XCHAL_UNALIGNED_LOAD_EXCEPTION 1 /* unaligned loads cause exc. */
#define XCHAL_UNALIGNED_STORE_EXCEPTION 1 /* unaligned stores cause exc.*/
#define XCHAL_UNALIGNED_LOAD_HW 0 /* unaligned loads work in hw */
#define XCHAL_UNALIGNED_STORE_HW 0 /* unaligned stores work in hw*/
#define XCHAL_SW_VERSION 1100002 /* sw version of this header */
#define XCHAL_CORE_ID "de212" /* alphanum core name
(CoreID) set in the Xtensa
Processor Generator */
#define XCHAL_BUILD_UNIQUE_ID 0x0005A985 /* 22-bit sw build ID */
/*
* These definitions describe the hardware targeted by this software.
*/
#define XCHAL_HW_CONFIGID0 0xC283DFFE /* ConfigID hi 32 bits*/
#define XCHAL_HW_CONFIGID1 0x1C85A985 /* ConfigID lo 32 bits*/
#define XCHAL_HW_VERSION_NAME "LX6.0.2" /* full version name */
#define XCHAL_HW_VERSION_MAJOR 2600 /* major ver# of targeted hw */
#define XCHAL_HW_VERSION_MINOR 2 /* minor ver# of targeted hw */
#define XCHAL_HW_VERSION 260002 /* major*100+minor */
#define XCHAL_HW_REL_LX6 1
#define XCHAL_HW_REL_LX6_0 1
#define XCHAL_HW_REL_LX6_0_2 1
#define XCHAL_HW_CONFIGID_RELIABLE 1
/* If software targets a *range* of hardware versions, these are the bounds: */
#define XCHAL_HW_MIN_VERSION_MAJOR 2600 /* major v of earliest tgt hw */
#define XCHAL_HW_MIN_VERSION_MINOR 2 /* minor v of earliest tgt hw */
#define XCHAL_HW_MIN_VERSION 260002 /* earliest targeted hw */
#define XCHAL_HW_MAX_VERSION_MAJOR 2600 /* major v of latest tgt hw */
#define XCHAL_HW_MAX_VERSION_MINOR 2 /* minor v of latest tgt hw */
#define XCHAL_HW_MAX_VERSION 260002 /* latest targeted hw */
/*----------------------------------------------------------------------
CACHE
----------------------------------------------------------------------*/
#define XCHAL_ICACHE_LINESIZE 32 /* I-cache line size in bytes */
#define XCHAL_DCACHE_LINESIZE 32 /* D-cache line size in bytes */
#define XCHAL_ICACHE_LINEWIDTH 5 /* log2(I line size in bytes) */
#define XCHAL_DCACHE_LINEWIDTH 5 /* log2(D line size in bytes) */
#define XCHAL_ICACHE_SIZE 8192 /* I-cache size in bytes or 0 */
#define XCHAL_DCACHE_SIZE 8192 /* D-cache size in bytes or 0 */
#define XCHAL_DCACHE_IS_WRITEBACK 1 /* writeback feature */
#define XCHAL_DCACHE_IS_COHERENT 0 /* MP coherence feature */
#define XCHAL_HAVE_PREFETCH 0 /* PREFCTL register */
#define XCHAL_HAVE_PREFETCH_L1 0 /* prefetch to L1 dcache */
#define XCHAL_PREFETCH_CASTOUT_LINES 0 /* dcache pref. castout bufsz */
#define XCHAL_PREFETCH_ENTRIES 0 /* cache prefetch entries */
#define XCHAL_PREFETCH_BLOCK_ENTRIES 0 /* prefetch block streams */
#define XCHAL_HAVE_CACHE_BLOCKOPS 0 /* block prefetch for caches */
#define XCHAL_HAVE_ICACHE_TEST 1 /* Icache test instructions */
#define XCHAL_HAVE_DCACHE_TEST 1 /* Dcache test instructions */
#define XCHAL_HAVE_ICACHE_DYN_WAYS 0 /* Icache dynamic way support */
#define XCHAL_HAVE_DCACHE_DYN_WAYS 0 /* Dcache dynamic way support */
/****************************************************************************
Parameters Useful for PRIVILEGED (Supervisory or Non-Virtualized) Code
****************************************************************************/
#ifndef XTENSA_HAL_NON_PRIVILEGED_ONLY
/*----------------------------------------------------------------------
CACHE
----------------------------------------------------------------------*/
#define XCHAL_HAVE_PIF 1 /* any outbound PIF present */
/* If present, cache size in bytes == (ways * 2^(linewidth + setwidth)). */
/* Number of cache sets in log2(lines per way): */
#define XCHAL_ICACHE_SETWIDTH 7
#define XCHAL_DCACHE_SETWIDTH 7
/* Cache set associativity (number of ways): */
#define XCHAL_ICACHE_WAYS 2
#define XCHAL_DCACHE_WAYS 2
/* Cache features: */
#define XCHAL_ICACHE_LINE_LOCKABLE 1
#define XCHAL_DCACHE_LINE_LOCKABLE 1
#define XCHAL_ICACHE_ECC_PARITY 0
#define XCHAL_DCACHE_ECC_PARITY 0
/* Cache access size in bytes (affects operation of SICW instruction): */
#define XCHAL_ICACHE_ACCESS_SIZE 4
#define XCHAL_DCACHE_ACCESS_SIZE 4
#define XCHAL_DCACHE_BANKS 1 /* number of banks */
/* Number of encoded cache attr bits (see <xtensa/hal.h> for decoded bits): */
#define XCHAL_CA_BITS 4
/* Whether MEMCTL register has anything useful */
#define XCHAL_USE_MEMCTL (((XCHAL_LOOP_BUFFER_SIZE > 0) || \
XCHAL_DCACHE_IS_COHERENT || \
XCHAL_HAVE_ICACHE_DYN_WAYS || \
XCHAL_HAVE_DCACHE_DYN_WAYS) && \
(XCHAL_HW_MIN_VERSION >= XTENSA_HWVERSION_RE_2012_0))
/*----------------------------------------------------------------------
INTERNAL I/D RAM/ROMs and XLMI
----------------------------------------------------------------------*/
#define XCHAL_NUM_INSTROM 0 /* number of core instr. ROMs */
#define XCHAL_NUM_INSTRAM 1 /* number of core instr. RAMs */
#define XCHAL_NUM_DATAROM 0 /* number of core data ROMs */
#define XCHAL_NUM_DATARAM 1 /* number of core data RAMs */
#define XCHAL_NUM_URAM 0 /* number of core unified RAMs*/
#define XCHAL_NUM_XLMI 1 /* number of core XLMI ports */
/* Instruction RAM 0: */
#define XCHAL_INSTRAM0_VADDR 0x40000000 /* virtual address */
#define XCHAL_INSTRAM0_PADDR 0x40000000 /* physical address */
#define XCHAL_INSTRAM0_SIZE 131072 /* size in bytes */
#define XCHAL_INSTRAM0_ECC_PARITY 0 /* ECC/parity type, 0=none */
/* Data RAM 0: */
#define XCHAL_DATARAM0_VADDR 0x3FFE0000 /* virtual address */
#define XCHAL_DATARAM0_PADDR 0x3FFE0000 /* physical address */
#define XCHAL_DATARAM0_SIZE 131072 /* size in bytes */
#define XCHAL_DATARAM0_ECC_PARITY 0 /* ECC/parity type, 0=none */
#define XCHAL_DATARAM0_BANKS 1 /* number of banks */
/* XLMI Port 0: */
#define XCHAL_XLMI0_VADDR 0x3FFC0000 /* virtual address */
#define XCHAL_XLMI0_PADDR 0x3FFC0000 /* physical address */
#define XCHAL_XLMI0_SIZE 131072 /* size in bytes */
#define XCHAL_XLMI0_ECC_PARITY 0 /* ECC/parity type, 0=none */
#define XCHAL_HAVE_IMEM_LOADSTORE 1 /* can load/store to IROM/IRAM*/
/*----------------------------------------------------------------------
INTERRUPTS and TIMERS
----------------------------------------------------------------------*/
#define XCHAL_HAVE_INTERRUPTS 1 /* interrupt option */
#define XCHAL_HAVE_HIGHPRI_INTERRUPTS 1 /* med/high-pri. interrupts */
#define XCHAL_HAVE_NMI 1 /* non-maskable interrupt */
#define XCHAL_HAVE_CCOUNT 1 /* CCOUNT reg. (timer option) */
#define XCHAL_NUM_TIMERS 3 /* number of CCOMPAREn regs */
#define XCHAL_NUM_INTERRUPTS 22 /* number of interrupts */
#define XCHAL_NUM_INTERRUPTS_LOG2 5 /* ceil(log2(NUM_INTERRUPTS)) */
#define XCHAL_NUM_EXTINTERRUPTS 17 /* num of external interrupts */
#define XCHAL_NUM_INTLEVELS 6 /* number of interrupt levels
(not including level zero) */
#define XCHAL_EXCM_LEVEL 3 /* level masked by PS.EXCM */
/* (always 1 in XEA1; levels 2 .. EXCM_LEVEL are "medium priority") */
/* Masks of interrupts at each interrupt level: */
#define XCHAL_INTLEVEL1_MASK 0x001F80FF
#define XCHAL_INTLEVEL2_MASK 0x00000100
#define XCHAL_INTLEVEL3_MASK 0x00200E00
#define XCHAL_INTLEVEL4_MASK 0x00001000
#define XCHAL_INTLEVEL5_MASK 0x00002000
#define XCHAL_INTLEVEL6_MASK 0x00000000
#define XCHAL_INTLEVEL7_MASK 0x00004000
/* Masks of interrupts at each range 1..n of interrupt levels: */
#define XCHAL_INTLEVEL1_ANDBELOW_MASK 0x001F80FF
#define XCHAL_INTLEVEL2_ANDBELOW_MASK 0x001F81FF
#define XCHAL_INTLEVEL3_ANDBELOW_MASK 0x003F8FFF
#define XCHAL_INTLEVEL4_ANDBELOW_MASK 0x003F9FFF
#define XCHAL_INTLEVEL5_ANDBELOW_MASK 0x003FBFFF
#define XCHAL_INTLEVEL6_ANDBELOW_MASK 0x003FBFFF
#define XCHAL_INTLEVEL7_ANDBELOW_MASK 0x003FFFFF
/* Level of each interrupt: */
#define XCHAL_INT0_LEVEL 1
#define XCHAL_INT1_LEVEL 1
#define XCHAL_INT2_LEVEL 1
#define XCHAL_INT3_LEVEL 1
#define XCHAL_INT4_LEVEL 1
#define XCHAL_INT5_LEVEL 1
#define XCHAL_INT6_LEVEL 1
#define XCHAL_INT7_LEVEL 1
#define XCHAL_INT8_LEVEL 2
#define XCHAL_INT9_LEVEL 3
#define XCHAL_INT10_LEVEL 3
#define XCHAL_INT11_LEVEL 3
#define XCHAL_INT12_LEVEL 4
#define XCHAL_INT13_LEVEL 5
#define XCHAL_INT14_LEVEL 7
#define XCHAL_INT15_LEVEL 1
#define XCHAL_INT16_LEVEL 1
#define XCHAL_INT17_LEVEL 1
#define XCHAL_INT18_LEVEL 1
#define XCHAL_INT19_LEVEL 1
#define XCHAL_INT20_LEVEL 1
#define XCHAL_INT21_LEVEL 3
#define XCHAL_DEBUGLEVEL 6 /* debug interrupt level */
#define XCHAL_HAVE_DEBUG_EXTERN_INT 1 /* OCD external db interrupt */
#define XCHAL_NMILEVEL 7 /* NMI "level" (for use with
EXCSAVE/EPS/EPC_n, RFI n) */
/* Type of each interrupt: */
#define XCHAL_INT0_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT1_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT2_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT3_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT4_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT5_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT6_TYPE XTHAL_INTTYPE_TIMER
#define XCHAL_INT7_TYPE XTHAL_INTTYPE_SOFTWARE
#define XCHAL_INT8_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT9_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT10_TYPE XTHAL_INTTYPE_TIMER
#define XCHAL_INT11_TYPE XTHAL_INTTYPE_SOFTWARE
#define XCHAL_INT12_TYPE XTHAL_INTTYPE_EXTERN_LEVEL
#define XCHAL_INT13_TYPE XTHAL_INTTYPE_TIMER
#define XCHAL_INT14_TYPE XTHAL_INTTYPE_NMI
#define XCHAL_INT15_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT16_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT17_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT18_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT19_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT20_TYPE XTHAL_INTTYPE_EXTERN_EDGE
#define XCHAL_INT21_TYPE XTHAL_INTTYPE_EXTERN_EDGE
/* Masks of interrupts for each type of interrupt: */
#define XCHAL_INTTYPE_MASK_UNCONFIGURED 0xFFC00000
#define XCHAL_INTTYPE_MASK_SOFTWARE 0x00000880
#define XCHAL_INTTYPE_MASK_EXTERN_EDGE 0x003F8000
#define XCHAL_INTTYPE_MASK_EXTERN_LEVEL 0x0000133F
#define XCHAL_INTTYPE_MASK_TIMER 0x00002440
#define XCHAL_INTTYPE_MASK_NMI 0x00004000
#define XCHAL_INTTYPE_MASK_WRITE_ERROR 0x00000000
#define XCHAL_INTTYPE_MASK_PROFILING 0x00000000
/* Interrupt numbers assigned to specific interrupt sources: */
#define XCHAL_TIMER0_INTERRUPT 6 /* CCOMPARE0 */
#define XCHAL_TIMER1_INTERRUPT 10 /* CCOMPARE1 */
#define XCHAL_TIMER2_INTERRUPT 13 /* CCOMPARE2 */
#define XCHAL_TIMER3_INTERRUPT XTHAL_TIMER_UNCONFIGURED
#define XCHAL_NMI_INTERRUPT 14 /* non-maskable interrupt */
/* Interrupt numbers for levels at which only one interrupt is configured: */
#define XCHAL_INTLEVEL2_NUM 8
#define XCHAL_INTLEVEL4_NUM 12
#define XCHAL_INTLEVEL5_NUM 13
#define XCHAL_INTLEVEL7_NUM 14
/* (There are many interrupts each at level(s) 1, 3.) */
/*
* External interrupt mapping.
* These macros describe how Xtensa processor interrupt numbers
* (as numbered internally, eg. in INTERRUPT and INTENABLE registers)
* map to external BInterrupt<n> pins, for those interrupts
* configured as external (level-triggered, edge-triggered, or NMI).
* See the Xtensa processor databook for more details.
*/
/* Core interrupt numbers mapped to each EXTERNAL BInterrupt pin number: */
#define XCHAL_EXTINT0_NUM 0 /* (intlevel 1) */
#define XCHAL_EXTINT1_NUM 1 /* (intlevel 1) */
#define XCHAL_EXTINT2_NUM 2 /* (intlevel 1) */
#define XCHAL_EXTINT3_NUM 3 /* (intlevel 1) */
#define XCHAL_EXTINT4_NUM 4 /* (intlevel 1) */
#define XCHAL_EXTINT5_NUM 5 /* (intlevel 1) */
#define XCHAL_EXTINT6_NUM 8 /* (intlevel 2) */
#define XCHAL_EXTINT7_NUM 9 /* (intlevel 3) */
#define XCHAL_EXTINT8_NUM 12 /* (intlevel 4) */
#define XCHAL_EXTINT9_NUM 14 /* (intlevel 7) */
#define XCHAL_EXTINT10_NUM 15 /* (intlevel 1) */
#define XCHAL_EXTINT11_NUM 16 /* (intlevel 1) */
#define XCHAL_EXTINT12_NUM 17 /* (intlevel 1) */
#define XCHAL_EXTINT13_NUM 18 /* (intlevel 1) */
#define XCHAL_EXTINT14_NUM 19 /* (intlevel 1) */
#define XCHAL_EXTINT15_NUM 20 /* (intlevel 1) */
#define XCHAL_EXTINT16_NUM 21 /* (intlevel 3) */
/* EXTERNAL BInterrupt pin numbers mapped to each core interrupt number: */
#define XCHAL_INT0_EXTNUM 0 /* (intlevel 1) */
#define XCHAL_INT1_EXTNUM 1 /* (intlevel 1) */
#define XCHAL_INT2_EXTNUM 2 /* (intlevel 1) */
#define XCHAL_INT3_EXTNUM 3 /* (intlevel 1) */
#define XCHAL_INT4_EXTNUM 4 /* (intlevel 1) */
#define XCHAL_INT5_EXTNUM 5 /* (intlevel 1) */
#define XCHAL_INT8_EXTNUM 6 /* (intlevel 2) */
#define XCHAL_INT9_EXTNUM 7 /* (intlevel 3) */
#define XCHAL_INT12_EXTNUM 8 /* (intlevel 4) */
#define XCHAL_INT14_EXTNUM 9 /* (intlevel 7) */
#define XCHAL_INT15_EXTNUM 10 /* (intlevel 1) */
#define XCHAL_INT16_EXTNUM 11 /* (intlevel 1) */
#define XCHAL_INT17_EXTNUM 12 /* (intlevel 1) */
#define XCHAL_INT18_EXTNUM 13 /* (intlevel 1) */
#define XCHAL_INT19_EXTNUM 14 /* (intlevel 1) */
#define XCHAL_INT20_EXTNUM 15 /* (intlevel 1) */
#define XCHAL_INT21_EXTNUM 16 /* (intlevel 3) */
/*----------------------------------------------------------------------
EXCEPTIONS and VECTORS
----------------------------------------------------------------------*/
#define XCHAL_XEA_VERSION 2 /* Xtensa Exception Architecture
number: 1 == XEA1 (old)
2 == XEA2 (new)
0 == XEAX (extern) or TX */
#define XCHAL_HAVE_XEA1 0 /* Exception Architecture 1 */
#define XCHAL_HAVE_XEA2 1 /* Exception Architecture 2 */
#define XCHAL_HAVE_XEAX 0 /* External Exception Arch. */
#define XCHAL_HAVE_EXCEPTIONS 1 /* exception option */
#define XCHAL_HAVE_HALT 0 /* halt architecture option */
#define XCHAL_HAVE_BOOTLOADER 0 /* boot loader (for TX) */
#define XCHAL_HAVE_MEM_ECC_PARITY 0 /* local memory ECC/parity */
#define XCHAL_HAVE_VECTOR_SELECT 1 /* relocatable vectors */
#define XCHAL_HAVE_VECBASE 1 /* relocatable vectors */
#define XCHAL_VECBASE_RESET_VADDR 0x60000000 /* VECBASE reset value */
#define XCHAL_VECBASE_RESET_PADDR 0x60000000
#define XCHAL_RESET_VECBASE_OVERLAP 0
#define XCHAL_RESET_VECTOR0_VADDR 0x50000000
#define XCHAL_RESET_VECTOR0_PADDR 0x50000000
#define XCHAL_RESET_VECTOR1_VADDR 0x40000400
#define XCHAL_RESET_VECTOR1_PADDR 0x40000400
#define XCHAL_RESET_VECTOR_VADDR 0x50000000
#define XCHAL_RESET_VECTOR_PADDR 0x50000000
#define XCHAL_USER_VECOFS 0x00000340
#define XCHAL_USER_VECTOR_VADDR 0x60000340
#define XCHAL_USER_VECTOR_PADDR 0x60000340
#define XCHAL_KERNEL_VECOFS 0x00000300
#define XCHAL_KERNEL_VECTOR_VADDR 0x60000300
#define XCHAL_KERNEL_VECTOR_PADDR 0x60000300
#define XCHAL_DOUBLEEXC_VECOFS 0x000003C0
#define XCHAL_DOUBLEEXC_VECTOR_VADDR 0x600003C0
#define XCHAL_DOUBLEEXC_VECTOR_PADDR 0x600003C0
#define XCHAL_WINDOW_OF4_VECOFS 0x00000000
#define XCHAL_WINDOW_UF4_VECOFS 0x00000040
#define XCHAL_WINDOW_OF8_VECOFS 0x00000080
#define XCHAL_WINDOW_UF8_VECOFS 0x000000C0
#define XCHAL_WINDOW_OF12_VECOFS 0x00000100
#define XCHAL_WINDOW_UF12_VECOFS 0x00000140
#define XCHAL_WINDOW_VECTORS_VADDR 0x60000000
#define XCHAL_WINDOW_VECTORS_PADDR 0x60000000
#define XCHAL_INTLEVEL2_VECOFS 0x00000180
#define XCHAL_INTLEVEL2_VECTOR_VADDR 0x60000180
#define XCHAL_INTLEVEL2_VECTOR_PADDR 0x60000180
#define XCHAL_INTLEVEL3_VECOFS 0x000001C0
#define XCHAL_INTLEVEL3_VECTOR_VADDR 0x600001C0
#define XCHAL_INTLEVEL3_VECTOR_PADDR 0x600001C0
#define XCHAL_INTLEVEL4_VECOFS 0x00000200
#define XCHAL_INTLEVEL4_VECTOR_VADDR 0x60000200
#define XCHAL_INTLEVEL4_VECTOR_PADDR 0x60000200
#define XCHAL_INTLEVEL5_VECOFS 0x00000240
#define XCHAL_INTLEVEL5_VECTOR_VADDR 0x60000240
#define XCHAL_INTLEVEL5_VECTOR_PADDR 0x60000240
#define XCHAL_INTLEVEL6_VECOFS 0x00000280
#define XCHAL_INTLEVEL6_VECTOR_VADDR 0x60000280
#define XCHAL_INTLEVEL6_VECTOR_PADDR 0x60000280
#define XCHAL_DEBUG_VECOFS XCHAL_INTLEVEL6_VECOFS
#define XCHAL_DEBUG_VECTOR_VADDR XCHAL_INTLEVEL6_VECTOR_VADDR
#define XCHAL_DEBUG_VECTOR_PADDR XCHAL_INTLEVEL6_VECTOR_PADDR
#define XCHAL_NMI_VECOFS 0x000002C0
#define XCHAL_NMI_VECTOR_VADDR 0x600002C0
#define XCHAL_NMI_VECTOR_PADDR 0x600002C0
#define XCHAL_INTLEVEL7_VECOFS XCHAL_NMI_VECOFS
#define XCHAL_INTLEVEL7_VECTOR_VADDR XCHAL_NMI_VECTOR_VADDR
#define XCHAL_INTLEVEL7_VECTOR_PADDR XCHAL_NMI_VECTOR_PADDR
/*----------------------------------------------------------------------
DEBUG MODULE
----------------------------------------------------------------------*/
/* Misc */
#define XCHAL_HAVE_DEBUG_ERI 1 /* ERI to debug module */
#define XCHAL_HAVE_DEBUG_APB 0 /* APB to debug module */
#define XCHAL_HAVE_DEBUG_JTAG 1 /* JTAG to debug module */
/* On-Chip Debug (OCD) */
#define XCHAL_HAVE_OCD 1 /* OnChipDebug option */
#define XCHAL_NUM_IBREAK 2 /* number of IBREAKn regs */
#define XCHAL_NUM_DBREAK 2 /* number of DBREAKn regs */
#define XCHAL_HAVE_OCD_DIR_ARRAY 0 /* faster OCD option (to LX4) */
#define XCHAL_HAVE_OCD_LS32DDR 1 /* L32DDR/S32DDR (faster OCD) */
/* TRAX (in core) */
#define XCHAL_HAVE_TRAX 1 /* TRAX in debug module */
#define XCHAL_TRAX_MEM_SIZE 262144 /* TRAX memory size in bytes */
#define XCHAL_TRAX_MEM_SHAREABLE 0 /* start/end regs; ready sig. */
#define XCHAL_TRAX_ATB_WIDTH 0 /* ATB width (bits), 0=no ATB */
#define XCHAL_TRAX_TIME_WIDTH 0 /* timestamp bitwidth, 0=none */
/* Perf counters */
#define XCHAL_NUM_PERF_COUNTERS 0 /* performance counters */
/*----------------------------------------------------------------------
MMU
----------------------------------------------------------------------*/
/* See core-matmap.h header file for more details. */
#define XCHAL_HAVE_TLBS 1 /* inverse of HAVE_CACHEATTR */
#define XCHAL_HAVE_SPANNING_WAY 1 /* one way maps I+D 4GB vaddr */
#define XCHAL_SPANNING_WAY 0 /* TLB spanning way number */
#define XCHAL_HAVE_IDENTITY_MAP 1 /* vaddr == paddr always */
#define XCHAL_HAVE_CACHEATTR 0 /* CACHEATTR register present */
#define XCHAL_HAVE_MIMIC_CACHEATTR 1 /* region protection */
#define XCHAL_HAVE_XLT_CACHEATTR 0 /* region prot. w/translation */
#define XCHAL_HAVE_PTP_MMU 0 /* full MMU (with page table
[autorefill] and protection)
usable for an MMU-based OS */
/* If none of the above last 4 are set, it's a custom TLB configuration. */
#define XCHAL_MMU_ASID_BITS 0 /* number of bits in ASIDs */
#define XCHAL_MMU_RINGS 1 /* number of rings (1..4) */
#define XCHAL_MMU_RING_BITS 0 /* num of bits in RING field */
#endif /* !XTENSA_HAL_NON_PRIVILEGED_ONLY */
#endif /* _XTENSA_CORE_CONFIGURATION_H */
/*
* tie-asm.h -- compile-time HAL assembler definitions dependent on CORE & TIE
*
* NOTE: This header file is not meant to be included directly.
*/
/* This header file contains assembly-language definitions (assembly
macros, etc.) for this specific Xtensa processor's TIE extensions
and options. It is customized to this Xtensa processor configuration.
Copyright (c) 1999-2015 Cadence Design Systems Inc.
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
"Software"), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to
the following conditions:
The above copyright notice and this permission notice shall be included
in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */
#ifndef _XTENSA_CORE_TIE_ASM_H
#define _XTENSA_CORE_TIE_ASM_H
/* Selection parameter values for save-area save/restore macros: */
/* Option vs. TIE: */
#define XTHAL_SAS_TIE 0x0001 /* custom extension or coprocessor */
#define XTHAL_SAS_OPT 0x0002 /* optional (and not a coprocessor) */
#define XTHAL_SAS_ANYOT 0x0003 /* both of the above */
/* Whether used automatically by compiler: */
#define XTHAL_SAS_NOCC 0x0004 /* not used by compiler w/o special opts/code */
#define XTHAL_SAS_CC 0x0008 /* used by compiler without special opts/code */
#define XTHAL_SAS_ANYCC 0x000C /* both of the above */
/* ABI handling across function calls: */
#define XTHAL_SAS_CALR 0x0010 /* caller-saved */
#define XTHAL_SAS_CALE 0x0020 /* callee-saved */
#define XTHAL_SAS_GLOB 0x0040 /* global across function calls (in thread) */
#define XTHAL_SAS_ANYABI 0x0070 /* all of the above three */
/* Misc */
#define XTHAL_SAS_ALL 0xFFFF /* include all default NCP contents */
#define XTHAL_SAS3(optie,ccuse,abi) ( ((optie) & XTHAL_SAS_ANYOT) \
| ((ccuse) & XTHAL_SAS_ANYCC) \
| ((abi) & XTHAL_SAS_ANYABI) )
/*
* Macro to store all non-coprocessor (extra) custom TIE and optional state
* (not including zero-overhead loop registers).
* Required parameters:
* ptr Save area pointer address register (clobbered)
* (register must contain a 4 byte aligned address).
* at1..at4 Four temporary address registers (first XCHAL_NCP_NUM_ATMPS
* registers are clobbered, the remaining are unused).
* Optional parameters:
* continue If macro invoked as part of a larger store sequence, set to 1
* if this is not the first in the sequence. Defaults to 0.
* ofs Offset from start of larger sequence (from value of first ptr
* in sequence) at which to store. Defaults to next available space
* (or 0 if <continue> is 0).
* select Select what category(ies) of registers to store, as a bitmask
* (see XTHAL_SAS_xxx constants). Defaults to all registers.
* alloc Select what category(ies) of registers to allocate; if any
* category is selected here that is not in <select>, space for
* the corresponding registers is skipped without doing any store.
*/
.macro xchal_ncp_store ptr at1 at2 at3 at4 continue=0 ofs=-1 select=XTHAL_SAS_ALL alloc=0
xchal_sa_start \continue, \ofs
// Optional caller-saved registers used by default by the compiler:
.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\select)
xchal_sa_align \ptr, 0, 1016, 4, 4
rsr.ACCLO \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+0
rsr.ACCHI \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+4
.set .Lxchal_ofs_, .Lxchal_ofs_ + 8
.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
xchal_sa_align \ptr, 0, 1016, 4, 4
.set .Lxchal_ofs_, .Lxchal_ofs_ + 8
.endif
// Optional caller-saved registers not used by default by the compiler:
.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\select)
xchal_sa_align \ptr, 0, 1004, 4, 4
rsr.SCOMPARE1 \at1 // conditional store option
s32i \at1, \ptr, .Lxchal_ofs_+0
rsr.M0 \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+4
rsr.M1 \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+8
rsr.M2 \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+12
rsr.M3 \at1 // MAC16 option
s32i \at1, \ptr, .Lxchal_ofs_+16
.set .Lxchal_ofs_, .Lxchal_ofs_ + 20
.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
xchal_sa_align \ptr, 0, 1004, 4, 4
.set .Lxchal_ofs_, .Lxchal_ofs_ + 20
.endif
.endm // xchal_ncp_store
/*
* Macro to load all non-coprocessor (extra) custom TIE and optional state
* (not including zero-overhead loop registers).
* Required parameters:
* ptr Save area pointer address register (clobbered)
* (register must contain a 4 byte aligned address).
* at1..at4 Four temporary address registers (first XCHAL_NCP_NUM_ATMPS
* registers are clobbered, the remaining are unused).
* Optional parameters:
* continue If macro invoked as part of a larger load sequence, set to 1
* if this is not the first in the sequence. Defaults to 0.
* ofs Offset from start of larger sequence (from value of first ptr
* in sequence) at which to load. Defaults to next available space
* (or 0 if <continue> is 0).
* select Select what category(ies) of registers to load, as a bitmask
* (see XTHAL_SAS_xxx constants). Defaults to all registers.
* alloc Select what category(ies) of registers to allocate; if any
* category is selected here that is not in <select>, space for
* the corresponding registers is skipped without doing any load.
*/
.macro xchal_ncp_load ptr at1 at2 at3 at4 continue=0 ofs=-1 select=XTHAL_SAS_ALL alloc=0
xchal_sa_start \continue, \ofs
// Optional caller-saved registers used by default by the compiler:
.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\select)
xchal_sa_align \ptr, 0, 1016, 4, 4
l32i \at1, \ptr, .Lxchal_ofs_+0
wsr.ACCLO \at1 // MAC16 option
l32i \at1, \ptr, .Lxchal_ofs_+4
wsr.ACCHI \at1 // MAC16 option
.set .Lxchal_ofs_, .Lxchal_ofs_ + 8
.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_CC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
xchal_sa_align \ptr, 0, 1016, 4, 4
.set .Lxchal_ofs_, .Lxchal_ofs_ + 8
.endif
// Optional caller-saved registers not used by default by the compiler:
.ifeq (XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\select)
xchal_sa_align \ptr, 0, 1004, 4, 4
l32i \at1, \ptr, .Lxchal_ofs_+0
wsr.SCOMPARE1 \at1 // conditional store option
l32i \at1, \ptr, .Lxchal_ofs_+4
wsr.M0 \at1 // MAC16 option
l32i \at1, \ptr, .Lxchal_ofs_+8
wsr.M1 \at1 // MAC16 option
l32i \at1, \ptr, .Lxchal_ofs_+12
wsr.M2 \at1 // MAC16 option
l32i \at1, \ptr, .Lxchal_ofs_+16
wsr.M3 \at1 // MAC16 option
.set .Lxchal_ofs_, .Lxchal_ofs_ + 20
.elseif ((XTHAL_SAS_OPT | XTHAL_SAS_NOCC | XTHAL_SAS_CALR) & ~(\alloc)) == 0
xchal_sa_align \ptr, 0, 1004, 4, 4
.set .Lxchal_ofs_, .Lxchal_ofs_ + 20
.endif
.endm // xchal_ncp_load
#define XCHAL_NCP_NUM_ATMPS 1
#define XCHAL_SA_NUM_ATMPS 1
#endif /*_XTENSA_CORE_TIE_ASM_H*/
/*
* tie.h -- compile-time HAL definitions dependent on CORE & TIE configuration
*
* NOTE: This header file is not meant to be included directly.
*/
/* This header file describes this specific Xtensa processor's TIE extensions
that extend basic Xtensa core functionality. It is customized to this
Xtensa processor configuration.
Copyright (c) 1999-2015 Cadence Design Systems Inc.
Permission is hereby granted, free of charge, to any person obtaining
a copy of this software and associated documentation files (the
"Software"), to deal in the Software without restriction, including
without limitation the rights to use, copy, modify, merge, publish,
distribute, sublicense, and/or sell copies of the Software, and to
permit persons to whom the Software is furnished to do so, subject to
the following conditions:
The above copyright notice and this permission notice shall be included
in all copies or substantial portions of the Software.
THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT.
IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY
CLAIM, DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT,
TORT OR OTHERWISE, ARISING FROM, OUT OF OR IN CONNECTION WITH THE
SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */
#ifndef _XTENSA_CORE_TIE_H
#define _XTENSA_CORE_TIE_H
#define XCHAL_CP_NUM 0 /* number of coprocessors */
#define XCHAL_CP_MAX 0 /* max CP ID + 1 (0 if none) */
#define XCHAL_CP_MASK 0x00 /* bitmask of all CPs by ID */
#define XCHAL_CP_PORT_MASK 0x00 /* bitmask of only port CPs */
/* Save area for non-coprocessor optional and custom (TIE) state: */
#define XCHAL_NCP_SA_SIZE 28
#define XCHAL_NCP_SA_ALIGN 4
/* Total save area for optional and custom state (NCP + CPn): */
#define XCHAL_TOTAL_SA_SIZE 32 /* with 16-byte align padding */
#define XCHAL_TOTAL_SA_ALIGN 4 /* actual minimum alignment */
/*
* Detailed contents of save areas.
* NOTE: caller must define the XCHAL_SA_REG macro (not defined here)
* before expanding the XCHAL_xxx_SA_LIST() macros.
*
* XCHAL_SA_REG(s,ccused,abikind,kind,opt,name,galign,align,asize,
* dbnum,base,regnum,bitsz,gapsz,reset,x...)
*
* s = passed from XCHAL_*_LIST(s), eg. to select how to expand
* ccused = set if used by compiler without special options or code
* abikind = 0 (caller-saved), 1 (callee-saved), or 2 (thread-global)
* kind = 0 (special reg), 1 (TIE user reg), or 2 (TIE regfile reg)
* opt = 0 (custom TIE extension or coprocessor), or 1 (optional reg)
* name = lowercase reg name (no quotes)
* galign = group byte alignment (power of 2) (galign >= align)
* align = register byte alignment (power of 2)
* asize = allocated size in bytes (asize*8 == bitsz + gapsz + padsz)
* (not including any pad bytes required to galign this or next reg)
* dbnum = unique target number f/debug (see <xtensa-libdb-macros.h>)
* base = reg shortname w/o index (or sr=special, ur=TIE user reg)
* regnum = reg index in regfile, or special/TIE-user reg number
* bitsz = number of significant bits (regfile width, or ur/sr mask bits)
* gapsz = intervening bits, if bitsz bits not stored contiguously
* (padsz = pad bits at end [TIE regfile] or at msbits [ur,sr] of asize)
* reset = register reset value (or 0 if undefined at reset)
* x = reserved for future use (0 until then)
*
* To filter out certain registers, e.g. to expand only the non-global
* registers used by the compiler, you can do something like this:
*
* #define XCHAL_SA_REG(s,ccused,p...) SELCC##ccused(p)
* #define SELCC0(p...)
* #define SELCC1(abikind,p...) SELAK##abikind(p)
* #define SELAK0(p...) REG(p)
* #define SELAK1(p...) REG(p)
* #define SELAK2(p...)
* #define REG(kind,tie,name,galn,aln,asz,csz,dbnum,base,rnum,bsz,rst,x...) \
* ...what you want to expand...
*/
#define XCHAL_NCP_SA_NUM 7
#define XCHAL_NCP_SA_LIST(s) \
XCHAL_SA_REG(s,1,0,0,1, acclo, 4, 4, 4,0x0210, sr,16 , 32,0,0,0) \
XCHAL_SA_REG(s,1,0,0,1, acchi, 4, 4, 4,0x0211, sr,17 , 8,0,0,0) \
XCHAL_SA_REG(s,0,0,0,1, scompare1, 4, 4, 4,0x020C, sr,12 , 32,0,0,0) \
XCHAL_SA_REG(s,0,0,0,1, m0, 4, 4, 4,0x0220, sr,32 , 32,0,0,0) \
XCHAL_SA_REG(s,0,0,0,1, m1, 4, 4, 4,0x0221, sr,33 , 32,0,0,0) \
XCHAL_SA_REG(s,0,0,0,1, m2, 4, 4, 4,0x0222, sr,34 , 32,0,0,0) \
XCHAL_SA_REG(s,0,0,0,1, m3, 4, 4, 4,0x0223, sr,35 , 32,0,0,0)
#define XCHAL_CP0_SA_NUM 0
#define XCHAL_CP0_SA_LIST(s) /* empty */
#define XCHAL_CP1_SA_NUM 0
#define XCHAL_CP1_SA_LIST(s) /* empty */
#define XCHAL_CP2_SA_NUM 0
#define XCHAL_CP2_SA_LIST(s) /* empty */
#define XCHAL_CP3_SA_NUM 0
#define XCHAL_CP3_SA_LIST(s) /* empty */
#define XCHAL_CP4_SA_NUM 0
#define XCHAL_CP4_SA_LIST(s) /* empty */
#define XCHAL_CP5_SA_NUM 0
#define XCHAL_CP5_SA_LIST(s) /* empty */
#define XCHAL_CP6_SA_NUM 0
#define XCHAL_CP6_SA_LIST(s) /* empty */
#define XCHAL_CP7_SA_NUM 0
#define XCHAL_CP7_SA_LIST(s) /* empty */
/* Byte length of instruction from its first nibble (op0 field), per FLIX. */
#define XCHAL_OP0_FORMAT_LENGTHS 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3
/* Byte length of instruction from its first byte, per FLIX. */
#define XCHAL_BYTE0_FORMAT_LENGTHS \
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3,\
3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3, 3,3,3,3,3,3,3,3,2,2,2,2,2,2,3,3
#endif /*_XTENSA_CORE_TIE_H*/
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment