Commit b053c1d0 authored by Hans de Goede's avatar Hans de Goede Committed by Mauro Carvalho Chehab

[media] gspca_pac73xx: Remove comments from before the 7302 / 7311 separation

The pac7302 and pac7311 driver still contains some comments from before
they were separated, such as marking certain functions 7302 or 7311 only,
with the new split drivers these make no sense, remove them.

Also removed the empty/unused sd_stop0 function from pac7311.c
Signed-off-by: default avatarHans de Goede <hdegoede@redhat.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent a648e310
......@@ -89,7 +89,6 @@ enum e_ctrl {
NCTRLS /* number of controls */
};
/* specific webcam descriptor for pac7302 */
struct sd {
struct gspca_dev gspca_dev; /* !! must be the first item */
......@@ -270,7 +269,6 @@ static const struct v4l2_pix_format vga_mode[] = {
#define LOAD_PAGE3 255
#define END_OF_SEQUENCE 0
/* pac 7302 */
static const u8 init_7302[] = {
/* index,value */
0xff, 0x01, /* page 1 */
......@@ -509,7 +507,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
return 0;
}
/* This function is used by pac7302 only */
static void setbrightcont(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
......@@ -536,7 +533,6 @@ static void setbrightcont(struct gspca_dev *gspca_dev)
reg_w(gspca_dev, 0xdc, 0x01);
}
/* This function is used by pac7302 only */
static void setcolors(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
......@@ -700,8 +696,6 @@ static int sd_start(struct gspca_dev *gspca_dev)
setautogain(gspca_dev);
sethvflip(gspca_dev);
/* only resolution 640x480 is supported for pac7302 */
sd->sof_read = 0;
atomic_set(&sd->avg_lum, 270 + sd->ctrls[BRIGHTNESS].val);
......
......@@ -20,31 +20,26 @@
*/
/* Some documentation about various registers as determined by trial and error.
When the register addresses differ between the 7202 and the 7311 the 2
different addresses are written as 7302addr/7311addr, when one of the 2
addresses is a - sign that register description is not valid for the
matching IC.
Register page 1:
Address Description
-/0x08 Unknown compressor related, must always be 8 except when not
0x08 Unknown compressor related, must always be 8 except when not
in 640x480 resolution and page 4 reg 2 <= 3 then set it to 9 !
-/0x1b Auto white balance related, bit 0 is AWB enable (inverted)
0x1b Auto white balance related, bit 0 is AWB enable (inverted)
bits 345 seem to toggle per color gains on/off (inverted)
0x78 Global control, bit 6 controls the LED (inverted)
-/0x80 JPEG compression ratio ? Best not touched
0x80 JPEG compression ratio ? Best not touched
Register page 3/4:
Register page 4:
Address Description
0x02 Clock divider 2-63, fps =~ 60 / val. Must be a multiple of 3 on
the 7302, so one of 3, 6, 9, ..., except when between 6 and 12?
-/0x0f Master gain 1-245, low value = high gain
0x10/- Master gain 0-31
-/0x10 Another gain 0-15, limited influence (1-2x gain I guess)
0x0f Master gain 1-245, low value = high gain
0x10 Another gain 0-15, limited influence (1-2x gain I guess)
0x21 Bitfield: 0-1 unused, 2-3 vflip/hflip, 4-5 unknown, 6-7 unused
-/0x27 Seems to toggle various gains on / off, Setting bit 7 seems to
0x27 Seems to toggle various gains on / off, Setting bit 7 seems to
completely disable the analog amplification block. Set to 0x68
for max gain, 0x14 for minimal gain.
*/
......@@ -60,7 +55,6 @@ MODULE_AUTHOR("Thomas Kaiser thomas@kaiser-linux.li");
MODULE_DESCRIPTION("Pixart PAC7311");
MODULE_LICENSE("GPL");
/* specific webcam descriptor for pac7311 */
struct sd {
struct gspca_dev gspca_dev; /* !! must be the first item */
......@@ -92,7 +86,6 @@ static int sd_setexposure(struct gspca_dev *gspca_dev, __s32 val);
static int sd_getexposure(struct gspca_dev *gspca_dev, __s32 *val);
static const struct ctrl sd_ctrls[] = {
/* This control is for both the 7302 and the 7311 */
{
{
.id = V4L2_CID_CONTRAST,
......@@ -108,7 +101,6 @@ static const struct ctrl sd_ctrls[] = {
.set = sd_setcontrast,
.get = sd_getcontrast,
},
/* All controls below are for both the 7302 and the 7311 */
{
{
.id = V4L2_CID_GAIN,
......@@ -206,7 +198,6 @@ static const struct v4l2_pix_format vga_mode[] = {
#define LOAD_PAGE4 254
#define END_OF_SEQUENCE 0
/* pac 7311 */
static const __u8 init_7311[] = {
0x78, 0x40, /* Bit_0=start stream, Bit_6=LED */
0x78, 0x40, /* Bit_0=start stream, Bit_6=LED */
......@@ -392,7 +383,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
cam = &gspca_dev->cam;
PDEBUG(D_CONF, "Find Sensor PAC7311");
cam->cam_mode = vga_mode;
cam->nmodes = ARRAY_SIZE(vga_mode);
......@@ -405,7 +395,6 @@ static int sd_config(struct gspca_dev *gspca_dev,
return 0;
}
/* This function is used by pac7311 only */
static void setcontrast(struct gspca_dev *gspca_dev)
{
struct sd *sd = (struct sd *) gspca_dev;
......@@ -438,7 +427,7 @@ static void setexposure(struct gspca_dev *gspca_dev)
struct sd *sd = (struct sd *) gspca_dev;
__u8 reg;
/* register 2 of frame 3/4 contains the clock divider configuring the
/* register 2 of page 4 contains the clock divider configuring the
no fps according to the formula: 60 / reg. sd->exposure is the
desired exposure time in ms. */
reg = 120 * sd->exposure / 1000;
......@@ -451,7 +440,7 @@ static void setexposure(struct gspca_dev *gspca_dev)
reg_w(gspca_dev, 0x02, reg);
/* Page 1 register 8 must always be 0x08 except when not in
640x480 mode and Page3/4 reg 2 <= 3 then it must be 9 */
640x480 mode and page 4 reg 2 <= 3 then it must be 9 */
reg_w(gspca_dev, 0xff, 0x01);
if (gspca_dev->cam.cam_mode[(int)gspca_dev->curr_mode].priv &&
reg <= 3) {
......@@ -499,12 +488,12 @@ static int sd_start(struct gspca_dev *gspca_dev)
/* set correct resolution */
switch (gspca_dev->cam.cam_mode[(int) gspca_dev->curr_mode].priv) {
case 2: /* 160x120 pac7311 */
case 2: /* 160x120 */
reg_w(gspca_dev, 0xff, 0x01);
reg_w(gspca_dev, 0x17, 0x20);
reg_w(gspca_dev, 0x87, 0x10);
break;
case 1: /* 320x240 pac7311 */
case 1: /* 320x240 */
reg_w(gspca_dev, 0xff, 0x01);
reg_w(gspca_dev, 0x17, 0x30);
reg_w(gspca_dev, 0x87, 0x11);
......@@ -541,11 +530,6 @@ static void sd_stopN(struct gspca_dev *gspca_dev)
reg_w(gspca_dev, 0x78, 0x44); /* Bit_0=start stream, Bit_6=LED */
}
/* called on streamoff with alt 0 and on disconnect for 7311 */
static void sd_stop0(struct gspca_dev *gspca_dev)
{
}
/* Include pac common sof detection functions */
#include "pac_common.h"
......@@ -820,7 +804,6 @@ static int sd_int_pkt_scan(struct gspca_dev *gspca_dev,
}
#endif
/* sub-driver description for pac7311 */
static const struct sd_desc sd_desc = {
.name = MODULE_NAME,
.ctrls = sd_ctrls,
......@@ -829,7 +812,6 @@ static const struct sd_desc sd_desc = {
.init = sd_init,
.start = sd_start,
.stopN = sd_stopN,
.stop0 = sd_stop0,
.pkt_scan = sd_pkt_scan,
.dq_callback = do_autogain,
#if defined(CONFIG_INPUT) || defined(CONFIG_INPUT_MODULE)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment