Commit b1cdfead authored by Bruce Allan's avatar Bruce Allan Committed by Jeff Kirsher

e1000e: checkpatch warnings - braces

WARNING: braces {} are not necessary for any arm of this statement
WARNING: braces {} are not necessary for single statement blocks
Signed-off-by: default avatarBruce Allan <bruce.w.allan@intel.com>
Tested-by: default avatarEmil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: default avatarJeff Kirsher <jeffrey.t.kirsher@intel.com>
parent 6480641e
......@@ -2309,11 +2309,10 @@ static s32 e1000_read_flash_data_ich8lan(struct e1000_hw *hw, u32 offset,
*/
if (ret_val == 0) {
flash_data = er32flash(ICH_FLASH_FDATA0);
if (size == 1) {
if (size == 1)
*data = (u8)(flash_data & 0x000000FF);
} else if (size == 2) {
else if (size == 2)
*data = (u16)(flash_data & 0x0000FFFF);
}
break;
} else {
/*
......
......@@ -493,9 +493,8 @@ s32 e1000e_check_for_copper_link(struct e1000_hw *hw)
* different link partner.
*/
ret_val = e1000e_config_fc_after_link_up(hw);
if (ret_val) {
if (ret_val)
e_dbg("Error configuring flow control\n");
}
return ret_val;
}
......@@ -1496,9 +1495,8 @@ s32 e1000e_setup_led_generic(struct e1000_hw *hw)
{
u32 ledctl;
if (hw->mac.ops.setup_led != e1000e_setup_led_generic) {
if (hw->mac.ops.setup_led != e1000e_setup_led_generic)
return -E1000_ERR_CONFIG;
}
if (hw->phy.media_type == e1000_media_type_fiber) {
ledctl = er32(LEDCTL);
......
......@@ -1806,10 +1806,9 @@ void e1000e_set_interrupt_capability(struct e1000_adapter *adapter)
err = pci_enable_msix(adapter->pdev,
adapter->msix_entries,
adapter->num_vectors);
if (err == 0) {
if (err == 0)
return;
}
}
/* MSI-X failed, so fall through and try MSI */
e_err("Failed to initialize MSI-X interrupts. "
"Falling back to MSI interrupts.\n");
......@@ -2198,9 +2197,8 @@ void e1000e_free_rx_resources(struct e1000_adapter *adapter)
e1000_clean_rx_ring(adapter);
for (i = 0; i < rx_ring->count; i++) {
for (i = 0; i < rx_ring->count; i++)
kfree(rx_ring->buffer_info[i].ps_pages);
}
vfree(rx_ring->buffer_info);
rx_ring->buffer_info = NULL;
......@@ -2240,20 +2238,18 @@ static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
/* handle TSO and jumbo frames */
if (bytes/packets > 8000)
retval = bulk_latency;
else if ((packets < 5) && (bytes > 512)) {
else if ((packets < 5) && (bytes > 512))
retval = low_latency;
}
break;
case low_latency: /* 50 usec aka 20000 ints/s */
if (bytes > 10000) {
/* this if handles the TSO accounting */
if (bytes/packets > 8000) {
if (bytes/packets > 8000)
retval = bulk_latency;
} else if ((packets < 10) || ((bytes/packets) > 1200)) {
else if ((packets < 10) || ((bytes/packets) > 1200))
retval = bulk_latency;
} else if ((packets > 35)) {
else if ((packets > 35))
retval = lowest_latency;
}
} else if (bytes/packets > 2000) {
retval = bulk_latency;
} else if (packets <= 2 && bytes < 512) {
......@@ -2262,9 +2258,8 @@ static unsigned int e1000_update_itr(struct e1000_adapter *adapter,
break;
case bulk_latency: /* 250 usec aka 4000 ints/s */
if (bytes > 25000) {
if (packets > 35) {
if (packets > 35)
retval = low_latency;
}
} else if (bytes < 6000) {
retval = low_latency;
}
......
......@@ -1057,9 +1057,8 @@ static s32 e1000_phy_setup_autoneg(struct e1000_hw *hw)
e_dbg("Auto-Neg Advertising %x\n", mii_autoneg_adv_reg);
if (phy->autoneg_mask & ADVERTISE_1000_FULL) {
if (phy->autoneg_mask & ADVERTISE_1000_FULL)
ret_val = e1e_wphy(hw, PHY_1000T_CTRL, mii_1000t_ctrl_reg);
}
return ret_val;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment