Commit b25e3a80 authored by Linus Torvalds's avatar Linus Torvalds

Merge bk://kernel.bkbits.net/davem/tg3-2.6

into home.osdl.org:/home/torvalds/v2.5/linux
parents 642b7fde b32b2542
......@@ -56,8 +56,8 @@
#define DRV_MODULE_NAME "tg3"
#define PFX DRV_MODULE_NAME ": "
#define DRV_MODULE_VERSION "2.5"
#define DRV_MODULE_RELDATE "December 22, 2003"
#define DRV_MODULE_VERSION "2.6"
#define DRV_MODULE_RELDATE "February 3, 2004"
#define TG3_DEF_MAC_MODE 0
#define TG3_DEF_RX_MODE 0
......@@ -5904,6 +5904,7 @@ do { p = orig_p + (reg); \
GET_REG32_LOOP(MSGINT_MODE, 0x0c);
GET_REG32_1(DMAC_MODE);
GET_REG32_LOOP(GRC_MODE, 0x4c);
if (tp->tg3_flags & TG3_FLAG_NVRAM)
GET_REG32_LOOP(NVRAM_CMD, 0x24);
#undef __GET_REG32
......@@ -7190,26 +7191,33 @@ static int __devinit tg3_do_test_dma(struct tg3 *tp, u32 *buf, dma_addr_t buf_dm
test_desc.addr_lo = buf_dma & 0xffffffff;
test_desc.nic_mbuf = 0x00002100;
test_desc.len = size;
/*
* HP ZX1 was seeing test failures for 5701 cards running at 33Mhz
* the *second* time the tg3 driver was getting loaded after an
* initial scan.
*
* Broadcom tells me:
* ...the DMA engine is connected to the GRC block and a DMA
* reset may affect the GRC block in some unpredictable way...
* The behavior of resets to individual blocks has not been tested.
*
* Broadcom noted the GRC reset will also reset all sub-components.
*/
if (to_device) {
test_desc.cqid_sqid = (13 << 8) | 2;
tw32(RDMAC_MODE, RDMAC_MODE_RESET);
tr32(RDMAC_MODE);
udelay(40);
tw32(RDMAC_MODE, RDMAC_MODE_ENABLE);
tr32(RDMAC_MODE);
udelay(40);
} else {
test_desc.cqid_sqid = (16 << 8) | 7;
tw32(WDMAC_MODE, WDMAC_MODE_RESET);
tr32(WDMAC_MODE);
udelay(40);
tw32(WDMAC_MODE, WDMAC_MODE_ENABLE);
tr32(WDMAC_MODE);
udelay(40);
}
test_desc.flags = 0x00000004;
test_desc.flags = 0x00000005;
for (i = 0; i < (sizeof(test_desc) / sizeof(u32)); i++) {
u32 val;
......@@ -7368,9 +7376,19 @@ static int __devinit tg3_test_dma(struct tg3 *tp)
GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5701) {
/* Remove this if it causes problems for some boards. */
tp->dma_rwctrl |= DMA_RWCTRL_USE_MEM_READ_MULT;
}
/* On 5700/5701 chips, we need to set this bit.
* Otherwise the chip will issue cacheline transactions
* to streamable DMA memory with not all the byte
* enables turned on. This is an error on several
* RISC PCI controllers, in particular sparc64.
*
* On 5703/5704 chips, this bit has been reassigned
* a different meaning. In particular, it is used
* on those chips to enable a PCI-X workaround.
*/
tp->dma_rwctrl |= DMA_RWCTRL_ASSERT_ALL_BE;
}
tw32(TG3PCI_DMA_RW_CTRL, tp->dma_rwctrl);
......@@ -7385,28 +7403,38 @@ static int __devinit tg3_test_dma(struct tg3 *tp)
goto out;
while (1) {
u32 *p, i;
u32 *p = buf, i;
p = buf;
for (i = 0; i < TEST_BUFFER_SIZE / sizeof(u32); i++)
p[i] = i;
/* Send the buffer to the chip. */
ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, 1);
if (ret)
if (ret) {
printk(KERN_ERR "tg3_test_dma() Write the buffer failed %d\n", ret);
break;
}
p = buf;
for (i = 0; i < TEST_BUFFER_SIZE / sizeof(u32); i++)
/* validate data reached card RAM correctly. */
for (i = 0; i < TEST_BUFFER_SIZE / sizeof(u32); i++) {
u32 val;
tg3_read_mem(tp, 0x2100 + (i*4), &val);
if (val != p[i]) {
printk( KERN_ERR " tg3_test_dma() Card buffer currupted on write! (%d != %d)\n", val, i);
/* ret = -ENODEV here? */
}
p[i] = 0;
}
/* Now read it back. */
ret = tg3_do_test_dma(tp, buf, buf_dma, TEST_BUFFER_SIZE, 0);
if (ret)
if (ret) {
printk(KERN_ERR "tg3_test_dma() Read the buffer failed %d\n", ret);
break;
}
/* Verify it. */
p = buf;
for (i = 0; i < TEST_BUFFER_SIZE / sizeof(u32); i++) {
if (p[i] == i)
continue;
......@@ -7417,6 +7445,7 @@ static int __devinit tg3_test_dma(struct tg3 *tp)
tw32(TG3PCI_DMA_RW_CTRL, tp->dma_rwctrl);
break;
} else {
printk(KERN_ERR "tg3_test_dma() buffer corrupted on read back! (%d != %d)\n", p[i], i);
ret = -ENODEV;
goto out;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment