Commit b446ff22 authored by Damien Riegel's avatar Damien Riegel Committed by Shawn Guo

ARM: dts: TS-4800: add basic device tree

This device tree adds support for TS-4800 by Technologic Systems. This
board is based on MX51-babbage, but there are some subtle differences in
the pins used, and there is an additional FPGA that is memory-mapped.

More details here:
  http://wiki.embeddedarm.com/wiki/TS-4800Signed-off-by: default avatarDamien Riegel <damien.riegel@savoirfairelinux.com>
Signed-off-by: default avatarShawn Guo <shawnguo@kernel.org>
parent 7ee70f23
......@@ -268,7 +268,8 @@ dtb-$(CONFIG_SOC_IMX51) += \
imx51-apf51dev.dtb \
imx51-babbage.dtb \
imx51-digi-connectcore-jsk.dtb \
imx51-eukrea-mbimxsd51-baseboard.dtb
imx51-eukrea-mbimxsd51-baseboard.dtb \
imx51-ts4800.dtb
dtb-$(CONFIG_SOC_IMX53) += \
imx53-ard.dtb \
imx53-m53evk.dtb \
......
/*
* Copyright 2015 Savoir-faire Linux
*
* This device tree is based on imx51-babbage.dts
*
* Licensed under the X11 license or the GPL v2 (or later)
*/
/dts-v1/;
#include "imx51.dtsi"
/ {
model = "Technologic Systems TS-4800";
compatible = "technologic,imx51-ts4800", "fsl,imx51";
chosen {
stdout-path = &uart1;
};
memory {
reg = <0x90000000 0x10000000>;
};
soc {
fpga {
compatible = "simple-bus";
reg = <0xb0000000 0x1d000>;
#address-cells = <1>;
#size-cells = <1>;
ranges;
syscon: syscon@b0010000 {
compatible = "syscon", "simple-mfd";
reg = <0xb0010000 0x3d>;
reg-io-width = <2>;
wdt@e {
compatible = "technologic,ts4800-wdt";
syscon = <&syscon 0xe>;
};
};
};
};
clocks {
ckih1 {
clock-frequency = <22579200>;
};
ckih2 {
clock-frequency = <24576000>;
};
};
};
&esdhc1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_esdhc1>;
cd-gpios = <&gpio1 0 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio1 1 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&fec {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_fec>;
phy-mode = "mii";
phy-reset-gpios = <&gpio2 14 GPIO_ACTIVE_LOW>;
phy-reset-duration = <1>;
status = "okay";
};
&i2c2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_i2c2>;
status = "okay";
rtc: m41t00@68 {
compatible = "stm,m41t00";
reg = <0x68>;
};
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
status = "okay";
};
&uart2 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart2>;
status = "okay";
};
&uart3 {
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart3>;
status = "okay";
};
&iomuxc {
pinctrl_ecspi1: ecspi1grp {
fsl,pins = <
MX51_PAD_CSPI1_MISO__ECSPI1_MISO 0x185
MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI 0x185
MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK 0x185
MX51_PAD_CSPI1_SS0__GPIO4_24 0x85 /* CS0 */
>;
};
pinctrl_esdhc1: esdhc1grp {
fsl,pins = <
MX51_PAD_SD1_CMD__SD1_CMD 0x400020d5
MX51_PAD_SD1_CLK__SD1_CLK 0x20d5
MX51_PAD_SD1_DATA0__SD1_DATA0 0x20d5
MX51_PAD_SD1_DATA1__SD1_DATA1 0x20d5
MX51_PAD_SD1_DATA2__SD1_DATA2 0x20d5
MX51_PAD_SD1_DATA3__SD1_DATA3 0x20d5
MX51_PAD_GPIO1_0__GPIO1_0 0x100
MX51_PAD_GPIO1_1__GPIO1_1 0x100
>;
};
pinctrl_fec: fecgrp {
fsl,pins = <
MX51_PAD_EIM_EB2__FEC_MDIO 0x000001f5
MX51_PAD_EIM_EB3__FEC_RDATA1 0x00000085
MX51_PAD_EIM_CS2__FEC_RDATA2 0x00000085
MX51_PAD_EIM_CS3__FEC_RDATA3 0x00000085
MX51_PAD_EIM_CS4__FEC_RX_ER 0x00000180
MX51_PAD_EIM_CS5__FEC_CRS 0x00000180
MX51_PAD_DISP2_DAT10__FEC_COL 0x00000180
MX51_PAD_DISP2_DAT11__FEC_RX_CLK 0x00000180
MX51_PAD_DISP2_DAT14__FEC_RDATA0 0x00002180
MX51_PAD_DISP2_DAT15__FEC_TDATA0 0x00002004
MX51_PAD_NANDF_CS2__FEC_TX_ER 0x00002004
MX51_PAD_DI2_PIN2__FEC_MDC 0x00002004
MX51_PAD_DISP2_DAT6__FEC_TDATA1 0x00002004
MX51_PAD_DISP2_DAT7__FEC_TDATA2 0x00002004
MX51_PAD_DISP2_DAT8__FEC_TDATA3 0x00002004
MX51_PAD_DISP2_DAT9__FEC_TX_EN 0x00002004
MX51_PAD_DISP2_DAT13__FEC_TX_CLK 0x00002180
MX51_PAD_DISP2_DAT12__FEC_RX_DV 0x000020a4
MX51_PAD_EIM_A20__GPIO2_14 0x00000085 /* Phy Reset */
>;
};
pinctrl_i2c2: i2c2grp {
fsl,pins = <
MX51_PAD_KEY_COL4__I2C2_SCL 0x400001ed
MX51_PAD_KEY_COL5__I2C2_SDA 0x400001ed
>;
};
pinctrl_uart1: uart1grp {
fsl,pins = <
MX51_PAD_UART1_RXD__UART1_RXD 0x1c5
MX51_PAD_UART1_TXD__UART1_TXD 0x1c5
MX51_PAD_UART1_RTS__UART1_RTS 0x1c5
MX51_PAD_UART1_CTS__UART1_CTS 0x1c5
>;
};
pinctrl_uart2: uart2grp {
fsl,pins = <
MX51_PAD_UART2_RXD__UART2_RXD 0x1c5
MX51_PAD_UART2_TXD__UART2_TXD 0x1c5
>;
};
pinctrl_uart3: uart3grp {
fsl,pins = <
MX51_PAD_EIM_D25__UART3_RXD 0x1c5
MX51_PAD_EIM_D26__UART3_TXD 0x1c5
MX51_PAD_EIM_D27__UART3_RTS 0x1c5
MX51_PAD_EIM_D24__UART3_CTS 0x1c5
>;
};
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment