ice: wait 5 s for EMP reset after firmware flash

We need to wait 5 s for EMP reset after firmware flash. Code was extracted
from OOT driver (ice v1.8.3 downloaded from sourceforge). Without this
wait, fw_activate let card in inconsistent state and recoverable only
by second flash/activate. Flash was tested on these fw's:
From -> To
 3.00 -> 3.10/3.20
 3.10 -> 3.00/3.20
 3.20 -> 3.00/3.10

Reproducer:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
    fw_activate
[root@host ~]# ip link show ens7f0
71: ens7f0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
    link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
    altname enp202s0f0

dmesg after flash:
[   55.120788] ice: Copyright (c) 2018, Intel Corporation.
[   55.274734] ice 0000:ca:00.0: Get PHY capabilities failed status = -5, continuing anyway
[   55.569797] ice 0000:ca:00.0: The DDP package was successfully loaded: ICE OS Default Package version 1.3.28.0
[   55.603629] ice 0000:ca:00.0: Get PHY capability failed.
[   55.608951] ice 0000:ca:00.0: ice_init_nvm_phy_type failed: -5
[   55.647348] ice 0000:ca:00.0: PTP init successful
[   55.675536] ice 0000:ca:00.0: DCB is enabled in the hardware, max number of TCs supported on this port are 8
[   55.685365] ice 0000:ca:00.0: FW LLDP is disabled, DCBx/LLDP in SW mode.
[   55.692179] ice 0000:ca:00.0: Commit DCB Configuration to the hardware
[   55.701382] ice 0000:ca:00.0: 126.024 Gb/s available PCIe bandwidth, limited by 16.0 GT/s PCIe x8 link at 0000:c9:02.0 (capable of 252.048 Gb/s with 16.0 GT/s PCIe x16 link)
Reboot doesn’t help, only second flash/activate with OOT or patched
driver put card back in consistent state.

After patch:
[root@host ~]# devlink dev flash pci/0000:ca:00.0 file E810_XXVDA4_FH_O_SEC_FW_1p6p1p9_NVM_3p10_PLDMoMCTP_0.11_8000AD7B.bin
Preparing to flash
[fw.mgmt] Erasing
[fw.mgmt] Erasing done
[fw.mgmt] Flashing 100%
[fw.mgmt] Flashing done 100%
[fw.undi] Erasing
[fw.undi] Erasing done
[fw.undi] Flashing 100%
[fw.undi] Flashing done 100%
[fw.netlist] Erasing
[fw.netlist] Erasing done
[fw.netlist] Flashing 100%
[fw.netlist] Flashing done 100%
Activate new firmware by devlink reload
[root@host ~]# devlink dev reload pci/0000:ca:00.0 action fw_activate
reload_actions_performed:
    fw_activate
[root@host ~]# ip link show ens7f0
19: ens7f0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP mode DEFAULT group default qlen 1000
    link/ether b4:96:91:dc:72:e0 brd ff:ff:ff:ff:ff:ff
    altname enp202s0f0

Fixes: 399e27db ("ice: support immediate firmware activation via devlink reload")
Signed-off-by: Petr Oros <poros@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

drivers/net/ethernet/intel/ice/ice_main.c

@@ -6929,12 +6929,15 @@ static void ice_rebuild(struct ice_pf *pf, enum ice_reset_req reset_type)
 
 	dev_dbg(dev, "rebuilding PF after reset_type=%d\n", reset_type);
 
+#define ICE_EMP_RESET_SLEEP_MS 5000
 	if (reset_type == ICE_RESET_EMPR) {
 		/* If an EMP reset has occurred, any previously pending flash
 		 * update will have completed. We no longer know whether or
 		 * not the NVM update EMP reset is restricted.
 		 */
 		pf->fw_emp_reset_disabled = false;
+
+		msleep(ICE_EMP_RESET_SLEEP_MS);
 	}
 
 	err = ice_init_all_ctrlq(hw);