Merge branch 'next/soc' into next/multiplatform

* next/soc: (50 commits)
  ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
  MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
  ARM: bcm2835: instantiate console UART
  ARM: bcm2835: add stub clock driver
  ARM: bcm2835: add system timer
  ARM: bcm2835: add interrupt controller driver
  ARM: add infra-structure for BCM2835 and Raspberry Pi
  ARM: tegra20: add CPU hotplug support
  ARM: tegra30: add CPU hotplug support
  ARM: tegra: clean up the common assembly macros into sleep.h
  ARM: tegra: replace the CPU CAR access code by tegra_cpu_car_ops
  ARM: tegra: introduce tegra_cpu_car_ops structures
  ARM: Tegra: Add smp_twd clock for Tegra20
  ARM: AM33XX: clock: Add dcan clock aliases for device-tree
  ARM: OMAP2+: dpll: Add missing soc_is_am33xx() check for common functions
  ARM: OMAP: omap_device: idle devices with no driver bound
  ARM: OMAP: omap_device: don't attempt late suspend if no driver bound
  ARM: OMAP: omap_device: keep track of driver bound status
  ARM: OMAP3+: hwmod: Add AM33XX HWMOD data
  ARM: OMAP2+: hwmod: Hook-up am33xx support in omap_hwmod framework
  ...

Change/remove conflict in arch/arm/mach-ux500/clock.c resolved.
Signed-off-by: Olof Johansson <olof@lixom.net>

Documentation/devicetree/bindings/arm/bcm2835.txt

+Broadcom BCM2835 device tree bindings
+-------------------------------------------
+
+Boards with the BCM2835 SoC shall have the following properties:
+
+Required root node property:
+
+compatible = "brcm,bcm2835";

Documentation/devicetree/bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt

+BCM2835 Top-Level ("ARMCTRL") Interrupt Controller
+
+The BCM2835 contains a custom top-level interrupt controller, which supports
+72 interrupt sources using a 2-level register scheme. The interrupt
+controller, or the HW block containing it, is referred to occasionally
+as "armctrl" in the SoC documentation, hence naming of this binding.
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-armctrl-ic.txt"
+- reg : Specifies base physical address and size of the registers.
+- interrupt-controller : Identifies the node as an interrupt controller
+- #interrupt-cells : Specifies the number of cells needed to encode an
+  interrupt source. The value shall be 2.
+
+  The 1st cell is the interrupt bank; 0 for interrupts in the "IRQ basic
+  pending" register, or 1/2 respectively for interrupts in the "IRQ pending
+  1/2" register.
+
+  The 2nd cell contains the interrupt number within the bank. Valid values
+  are 0..7 for bank 0, and 0..31 for bank 1.
+
+The interrupt sources are as follows:
+
+Bank 0:
+0: ARM_TIMER
+1: ARM_MAILBOX
+2: ARM_DOORBELL_0
+3: ARM_DOORBELL_1
+4: VPU0_HALTED
+5: VPU1_HALTED
+6: ILLEGAL_TYPE0
+7: ILLEGAL_TYPE1
+
+Bank 1:
+0: TIMER0
+1: TIMER1
+2: TIMER2
+3: TIMER3
+4: CODEC0
+5: CODEC1
+6: CODEC2
+7: VC_JPEG
+8: ISP
+9: VC_USB
+10: VC_3D
+11: TRANSPOSER
+12: MULTICORESYNC0
+13: MULTICORESYNC1
+14: MULTICORESYNC2
+15: MULTICORESYNC3
+16: DMA0
+17: DMA1
+18: VC_DMA2
+19: VC_DMA3
+20: DMA4
+21: DMA5
+22: DMA6
+23: DMA7
+24: DMA8
+25: DMA9
+26: DMA10
+27: DMA11
+28: DMA12
+29: AUX
+30: ARM
+31: VPUDMA
+
+Bank 2:
+0: HOSTPORT
+1: VIDEOSCALER
+2: CCP2TX
+3: SDC
+4: DSI0
+5: AVE
+6: CAM0
+7: CAM1
+8: HDMI0
+9: HDMI1
+10: PIXELVALVE1
+11: I2CSPISLV
+12: DSI1
+13: PWA0
+14: PWA1
+15: CPR
+16: SMI
+17: GPIO0
+18: GPIO1
+19: GPIO2
+20: GPIO3
+21: VC_I2C
+22: VC_SPI
+23: VC_I2SPCM
+24: VC_SDIO
+25: VC_UART
+26: SLIMBUS
+27: VEC
+28: CPG
+29: RNG
+30: VC_ARASANSDIO
+31: AVSPMON
+
+Example:
+
+intc: interrupt-controller {
+	compatible = "brcm,bcm2835-armctrl-ic";
+	reg = <0x7e00b200 0x200>;
+	interrupt-controller;
+	#interrupt-cells = <2>;
+};

Documentation/devicetree/bindings/timer/brcm,bcm2835-system-timer.txt

+BCM2835 System Timer
+
+The System Timer peripheral provides four 32-bit timer channels and a
+single 64-bit free running counter. Each channel has an output compare
+register, which is compared against the 32 least significant bits of the
+free running counter values, and generates an interrupt.
+
+Required properties:
+
+- compatible : should be "brcm,bcm2835-system-timer.txt"
+- reg : Specifies base physical address and size of the registers.
+- interrupts : A list of 4 interrupt sinks; one per timer channel.
+- clock-frequency : The frequency of the clock that drives the counter, in Hz.
+
+Example:
+
+timer {
+	compatible = "brcm,bcm2835-system-timer";
+	reg = <0x7e003000 0x1000>;
+	interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+	clock-frequency = <1000000>;
+};

Documentation/devicetree/bindings/vendor-prefixes.txt

@@ -10,6 +10,7 @@ apm	Applied Micro Circuits Corporation (APM)
 arm	ARM Ltd.
 atmel	Atmel Corporation
 bosch	Bosch Sensortec GmbH
+brcm	Broadcom Corporation
 cavium	Cavium, Inc.
 chrp	Common Hardware Reference Platform
 cortina	Cortina Systems, Inc.

MAINTAINERS

@@ -1612,6 +1612,16 @@ L:	netdev@vger.kernel.org
 S:	Supported
 F:	drivers/net/ethernet/broadcom/bnx2x/
 
+BROADCOM BCM2835 ARM ARCHICTURE
+M:	Stephen Warren <swarren@wwwdotorg.org>
+L:	linux-rpi-kernel@lists.infradead.org (moderated for non-subscribers)
+T:	git git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-rpi.git
+S:	Maintained
+F:	arch/arm/mach-bcm2835/
+F:	arch/arm/boot/dts/bcm2835*
+F:	arch/arm/configs/bcm2835_defconfig
+F:	drivers/*/*bcm2835*
+
 BROADCOM TG3 GIGABIT ETHERNET DRIVER
 M:	Matt Carlson <mcarlson@broadcom.com>
 M:	Michael Chan <mchan@broadcom.com>

arch/arm/Kconfig

@@ -347,6 +347,23 @@ config ARCH_AT91
 	  This enables support for systems based on Atmel
 	  AT91RM9200 and AT91SAM9* processors.
 
+config ARCH_BCM2835
+	bool "Broadcom BCM2835 family"
+	select ARCH_WANT_OPTIONAL_GPIOLIB
+	select ARM_AMBA
+	select ARM_ERRATA_411920
+	select ARM_TIMER_SP804
+	select CLKDEV_LOOKUP
+	select COMMON_CLK
+	select CPU_V6
+	select GENERIC_CLOCKEVENTS
+	select MULTI_IRQ_HANDLER
+	select SPARSE_IRQ
+	select USE_OF
+	help
+	  This enables support for the Broadcom BCM2835 SoC. This SoC is
+	  use in the Raspberry Pi, and Roku 2 devices.
+
 config ARCH_BCMRING
 	bool "Broadcom BCMRING"
 	depends on MMU
@@ -674,6 +691,7 @@ config ARCH_TEGRA
 	select MIGHT_HAVE_CACHE_L2X0
 	select ARCH_HAS_CPUFREQ
 	select USE_OF
+	select COMMON_CLK
 	help
 	  This enables support for NVIDIA Tegra based systems (Tegra APX,
 	  Tegra 6xx and Tegra 2 series).

arch/arm/Makefile

@@ -136,6 +136,7 @@ textofs-$(CONFIG_ARCH_MSM8960) := 0x00208000
 # Machine directory name.  This list is sorted alphanumerically
 # by CONFIG_* macro name.
 machine-$(CONFIG_ARCH_AT91)		:= at91
+machine-$(CONFIG_ARCH_BCM2835)		:= bcm2835
 machine-$(CONFIG_ARCH_BCMRING)		:= bcmring
 machine-$(CONFIG_ARCH_CLPS711X)		:= clps711x
 machine-$(CONFIG_ARCH_CNS3XXX)		:= cns3xxx

arch/arm/boot/dts/bcm2835-rpi-b.dts

+/dts-v1/;
+/memreserve/ 0x0c000000 0x04000000;
+/include/ "bcm2835.dtsi"
+
+/ {
+	compatible = "raspberrypi,model-b", "brcm,bcm2835";
+	model = "Raspberry Pi Model B";
+
+	memory {
+		reg = <0 0x10000000>;
+	};
+};

arch/arm/boot/dts/bcm2835.dtsi

+/include/ "skeleton.dtsi"
+
+/ {
+	compatible = "brcm,bcm2835";
+	model = "BCM2835";
+	interrupt-parent = <&intc>;
+
+	chosen {
+		bootargs = "earlyprintk console=ttyAMA0";
+	};
+
+	soc {
+		compatible = "simple-bus";
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x7e000000 0x20000000 0x02000000>;
+
+		timer {
+			compatible = "brcm,bcm2835-system-timer";
+			reg = <0x7e003000 0x1000>;
+			interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
+			clock-frequency = <1000000>;
+		};
+
+		intc: interrupt-controller {
+			compatible = "brcm,bcm2835-armctrl-ic";
+			reg = <0x7e00b200 0x200>;
+			interrupt-controller;
+			#interrupt-cells = <2>;
+		};
+
+		uart@20201000 {
+			compatible = "brcm,bcm2835-pl011", "arm,pl011", "arm,primecell";
+			reg = <0x7e201000 0x1000>;
+			interrupts = <2 25>;
+			clock-frequency = <3000000>;
+		};
+	};
+};

arch/arm/configs/bcm2835_defconfig

+CONFIG_EXPERIMENTAL=y
+# CONFIG_LOCALVERSION_AUTO is not set
+CONFIG_SYSVIPC=y
+CONFIG_BSD_PROCESS_ACCT=y
+CONFIG_BSD_PROCESS_ACCT_V3=y
+CONFIG_FHANDLE=y
+CONFIG_NO_HZ=y
+CONFIG_HIGH_RES_TIMERS=y
+CONFIG_LOG_BUF_SHIFT=18
+CONFIG_CGROUP_FREEZER=y
+CONFIG_CGROUP_DEVICE=y
+CONFIG_CPUSETS=y
+CONFIG_CGROUP_CPUACCT=y
+CONFIG_RESOURCE_COUNTERS=y
+CONFIG_CGROUP_PERF=y
+CONFIG_CFS_BANDWIDTH=y
+CONFIG_RT_GROUP_SCHED=y
+CONFIG_NAMESPACES=y
+CONFIG_SCHED_AUTOGROUP=y
+CONFIG_RELAY=y
+CONFIG_BLK_DEV_INITRD=y
+CONFIG_RD_BZIP2=y
+CONFIG_RD_LZMA=y
+CONFIG_RD_XZ=y
+CONFIG_RD_LZO=y
+CONFIG_CC_OPTIMIZE_FOR_SIZE=y
+CONFIG_KALLSYMS_ALL=y
+CONFIG_EMBEDDED=y
+# CONFIG_COMPAT_BRK is not set
+CONFIG_PROFILING=y
+CONFIG_OPROFILE=y
+CONFIG_JUMP_LABEL=y
+# CONFIG_BLOCK is not set
+CONFIG_ARCH_BCM2835=y
+CONFIG_PREEMPT_VOLUNTARY=y
+CONFIG_AEABI=y
+CONFIG_COMPACTION=y
+CONFIG_KSM=y
+CONFIG_DEFAULT_MMAP_MIN_ADDR=65536
+CONFIG_CLEANCACHE=y
+CONFIG_SECCOMP=y
+CONFIG_CC_STACKPROTECTOR=y
+CONFIG_KEXEC=y
+CONFIG_CRASH_DUMP=y
+CONFIG_VFP=y
+# CONFIG_CORE_DUMP_DEFAULT_ELF_HEADERS is not set
+# CONFIG_SUSPEND is not set
+CONFIG_DEVTMPFS=y
+CONFIG_DEVTMPFS_MOUNT=y
+# CONFIG_STANDALONE is not set
+# CONFIG_INPUT_MOUSEDEV is not set
+# CONFIG_INPUT_KEYBOARD is not set
+# CONFIG_INPUT_MOUSE is not set
+# CONFIG_SERIO is not set
+# CONFIG_VT is not set
+# CONFIG_UNIX98_PTYS is not set
+# CONFIG_LEGACY_PTYS is not set
+# CONFIG_DEVKMEM is not set
+CONFIG_SERIAL_AMBA_PL011=y
+CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
+CONFIG_TTY_PRINTK=y
+# CONFIG_HW_RANDOM is not set
+# CONFIG_HWMON is not set
+# CONFIG_USB_SUPPORT is not set
+# CONFIG_IOMMU_SUPPORT is not set
+# CONFIG_FILE_LOCKING is not set
+# CONFIG_DNOTIFY is not set
+# CONFIG_INOTIFY_USER is not set
+# CONFIG_PROC_FS is not set
+# CONFIG_SYSFS is not set
+# CONFIG_MISC_FILESYSTEMS is not set
+CONFIG_PRINTK_TIME=y
+# CONFIG_ENABLE_WARN_DEPRECATED is not set
+# CONFIG_ENABLE_MUST_CHECK is not set
+CONFIG_UNUSED_SYMBOLS=y
+CONFIG_LOCKUP_DETECTOR=y
+CONFIG_DEBUG_INFO=y
+CONFIG_DEBUG_MEMORY_INIT=y
+CONFIG_BOOT_PRINTK_DELAY=y
+CONFIG_SCHED_TRACER=y
+CONFIG_STACK_TRACER=y
+CONFIG_FUNCTION_PROFILER=y
+CONFIG_DYNAMIC_DEBUG=y
+CONFIG_KGDB=y
+CONFIG_KGDB_KDB=y
+CONFIG_TEST_KSTRTOX=y
+CONFIG_STRICT_DEVMEM=y
+CONFIG_DEBUG_LL=y
+CONFIG_EARLY_PRINTK=y
+# CONFIG_XZ_DEC_X86 is not set
+# CONFIG_XZ_DEC_POWERPC is not set
+# CONFIG_XZ_DEC_IA64 is not set
+# CONFIG_XZ_DEC_ARM is not set
+# CONFIG_XZ_DEC_ARMTHUMB is not set
+# CONFIG_XZ_DEC_SPARC is not set

arch/arm/configs/kzm9d_defconfig

@@ -8,6 +8,7 @@ CONFIG_LOG_BUF_SHIFT=16
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
 CONFIG_SLAB=y
 # CONFIG_BLK_DEV_BSG is not set
 # CONFIG_IOSCHED_DEADLINE is not set

arch/arm/configs/kzm9g_defconfig

@@ -14,6 +14,7 @@ CONFIG_NAMESPACES=y
 CONFIG_CC_OPTIMIZE_FOR_SIZE=y
 CONFIG_SYSCTL_SYSCALL=y
 CONFIG_EMBEDDED=y
+CONFIG_PERF_EVENTS=y
 CONFIG_SLAB=y
 CONFIG_MODULES=y
 CONFIG_MODULE_FORCE_LOAD=y

arch/arm/mach-bcm2835/Makefile

+obj-y += bcm2835.o

arch/arm/mach-bcm2835/Makefile.boot

+   zreladdr-y := 0x00008000
+params_phys-y := 0x00000100
+initrd_phys-y := 0x00800000
+
+dtb-y += bcm2835-rpi-b.dtb

arch/arm/mach-bcm2835/bcm2835.c

+/*
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/init.h>
+#include <linux/irqchip/bcm2835.h>
+#include <linux/of_platform.h>
+#include <linux/bcm2835_timer.h>
+#include <linux/clk/bcm2835.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/bcm2835_soc.h>
+
+static struct map_desc io_map __initdata = {
+	.virtual = BCM2835_PERIPH_VIRT,
+	.pfn = __phys_to_pfn(BCM2835_PERIPH_PHYS),
+	.length = BCM2835_PERIPH_SIZE,
+	.type = MT_DEVICE
+};
+
+void __init bcm2835_map_io(void)
+{
+	iotable_init(&io_map, 1);
+}
+
+void __init bcm2835_init(void)
+{
+	int ret;
+
+	bcm2835_init_clocks();
+
+	ret = of_platform_populate(NULL, of_default_bus_match_table, NULL,
+				   NULL);
+	if (ret) {
+		pr_err("of_platform_populate failed: %d\n", ret);
+		BUG();
+	}
+}
+
+static const char * const bcm2835_compat[] = {
+	"brcm,bcm2835",
+	NULL
+};
+
+DT_MACHINE_START(BCM2835, "BCM2835")
+	.map_io = bcm2835_map_io,
+	.init_irq = bcm2835_init_irq,
+	.handle_irq = bcm2835_handle_irq,
+	.init_machine = bcm2835_init,
+	.timer = &bcm2835_timer,
+	.dt_compat = bcm2835_compat
+MACHINE_END

arch/arm/mach-bcm2835/include/mach/bcm2835_soc.h

+/*
+ * Copyright (C) 2012 Stephen Warren
+ *
+ * Derived from code:
+ * Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MACH_BCM2835_BCM2835_SOC_H__
+#define __MACH_BCM2835_BCM2835_SOC_H__
+
+#include <asm/sizes.h>
+
+#define BCM2835_PERIPH_PHYS	0x20000000
+#define BCM2835_PERIPH_VIRT	0xf0000000
+#define BCM2835_PERIPH_SIZE	SZ_16M
+#define BCM2835_DEBUG_PHYS	0x20201000
+#define BCM2835_DEBUG_VIRT	0xf0201000
+
+#endif

arch/arm/mach-bcm2835/include/mach/debug-macro.S

+/*
+ * Debugging macro include header
+ *
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 1994-1999 Russell King
+ * Moved from linux/arch/arm/kernel/debug.S by Ben Dooks
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ */
+
+#include <mach/bcm2835_soc.h>
+
+	.macro	addruart, rp, rv, tmp
+	ldr	\rp, =BCM2835_DEBUG_PHYS
+	ldr	\rv, =BCM2835_DEBUG_VIRT
+	.endm
+
+#include <asm/hardware/debug-pl01x.S>

arch/arm/mach-bcm2835/include/mach/timex.h

+/*
+ *  BCM2835 system clock frequency
+ *
+ *  Copyright (C) 2010 Broadcom
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#ifndef __ASM_ARCH_TIMEX_H
+#define __ASM_ARCH_TIMEX_H
+
+#define CLOCK_TICK_RATE		(1000000)
+
+#endif

arch/arm/mach-bcm2835/include/mach/uncompress.h

+/*
+ * Copyright (C) 2010 Broadcom
+ * Copyright (C) 2003 ARM Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/amba/serial.h>
+#include <mach/bcm2835_soc.h>
+
+#define UART0_BASE BCM2835_DEBUG_PHYS
+
+#define BCM2835_UART_DR IOMEM(UART0_BASE + UART01x_DR)
+#define BCM2835_UART_FR IOMEM(UART0_BASE + UART01x_FR)
+#define BCM2835_UART_CR IOMEM(UART0_BASE + UART011_CR)
+
+static inline void putc(int c)
+{
+	while (__raw_readl(BCM2835_UART_FR) & UART01x_FR_TXFF)
+		barrier();
+
+	__raw_writel(c, BCM2835_UART_DR);
+}
+
+static inline void flush(void)
+{
+	int fr;
+
+	do {
+		fr = __raw_readl(BCM2835_UART_FR);
+		barrier();
+	} while ((fr & (UART011_FR_TXFE | UART01x_FR_BUSY)) != UART011_FR_TXFE);
+}
+
+#define arch_decomp_setup()
+#define arch_decomp_wdog()

arch/arm/mach-imx/clk-imx35.c

@@ -62,8 +62,8 @@ enum mx35_clks {
 	kpp_gate, mlb_gate, mshc_gate, owire_gate, pwm_gate, rngc_gate,
 	rtc_gate, rtic_gate, scc_gate, sdma_gate, spba_gate, spdif_gate,
 	ssi1_gate, ssi2_gate, uart1_gate, uart2_gate, uart3_gate, usbotg_gate,
-	wdog_gate, max_gate, admux_gate, csi_gate, iim_gate, gpu2d_gate,
-	clk_max
+	wdog_gate, max_gate, admux_gate, csi_gate, csi_div, csi_sel, iim_gate,
+	gpu2d_gate, clk_max
 };
 
 static struct clk *clk[clk_max];
@@ -142,6 +142,9 @@ int __init mx35_clocks_init()
 
 	clk[nfc_div] = imx_clk_divider("nfc_div", "ahb", base + MX35_CCM_PDR4, 28, 4);
 
+	clk[csi_sel] = imx_clk_mux("csi_sel", base + MX35_CCM_PDR2, 7, 1, std_sel, ARRAY_SIZE(std_sel));
+	clk[csi_div] = imx_clk_divider("csi_div", "csi_sel", base + MX35_CCM_PDR2, 16, 6);
+
 	clk[asrc_gate] = imx_clk_gate2("asrc_gate", "ipg", base + MX35_CCM_CGR0,  0);
 	clk[pata_gate] = imx_clk_gate2("pata_gate", "ipg", base + MX35_CCM_CGR0,  2);
 	clk[audmux_gate] = imx_clk_gate2("audmux_gate", "ipg", base + MX35_CCM_CGR0,  4);
@@ -192,7 +195,7 @@ int __init mx35_clocks_init()
 	clk[max_gate] = imx_clk_gate2("max_gate", "dummy", base + MX35_CCM_CGR2, 26);
 	clk[admux_gate] = imx_clk_gate2("admux_gate", "ipg", base + MX35_CCM_CGR2, 30);
 
-	clk[csi_gate] = imx_clk_gate2("csi_gate", "ipg", base + MX35_CCM_CGR3,  0);
+	clk[csi_gate] = imx_clk_gate2("csi_gate", "csi_div", base + MX35_CCM_CGR3,  0);
 	clk[iim_gate] = imx_clk_gate2("iim_gate", "ipg", base + MX35_CCM_CGR3,  2);
 	clk[gpu2d_gate] = imx_clk_gate2("gpu2d_gate", "ahb", base + MX35_CCM_CGR3,  4);
 
@@ -228,6 +231,7 @@ int __init mx35_clocks_init()
 	clk_register_clkdev(clk[i2c3_gate], NULL, "imx-i2c.2");
 	clk_register_clkdev(clk[ipu_gate], NULL, "ipu-core");
 	clk_register_clkdev(clk[ipu_gate], NULL, "mx3_sdc_fb");
+	clk_register_clkdev(clk[kpp_gate], NULL, "imx-keypad");
 	clk_register_clkdev(clk[owire_gate], NULL, "mxc_w1");
 	clk_register_clkdev(clk[sdma_gate], NULL, "imx35-sdma");
 	clk_register_clkdev(clk[ssi1_gate], NULL, "imx-ssi.0");
@@ -253,6 +257,7 @@ int __init mx35_clocks_init()
 	clk_register_clkdev(clk[usbotg_gate], "ahb", "fsl-usb2-udc");
 	clk_register_clkdev(clk[wdog_gate], NULL, "imx2-wdt.0");
 	clk_register_clkdev(clk[nfc_div], NULL, "mxc_nand.0");
+	clk_register_clkdev(clk[csi_gate], NULL, "mx3-camera.0");
 
 	clk_prepare_enable(clk[spba_gate]);
 	clk_prepare_enable(clk[gpio1_gate]);

arch/arm/mach-imx/clk-imx51-imx53.c

@@ -49,6 +49,7 @@ static const char *mx53_tve_ext_sel[] = { "pll4_sw", "ckih1", };
 static const char *tve_sel[] = { "tve_pred", "tve_ext_sel", };
 static const char *ipu_sel[] = { "axi_a", "axi_b", "emi_slow_gate", "ahb", };
 static const char *vpu_sel[] = { "axi_a", "axi_b", "emi_slow_gate", "ahb", };
+static const char *mx53_can_sel[] = { "ipg", "ckih1", "ckih2", "lp_apm", };
 
 enum imx5_clks {
 	dummy, ckil, osc, ckih1, ckih2, ahb, ipg, axi_a, axi_b, uart_pred,
@@ -82,6 +83,7 @@ enum imx5_clks {
 	ssi_ext1_podf, ssi_ext2_pred, ssi_ext2_podf, ssi1_root_gate,
 	ssi2_root_gate, ssi3_root_gate, ssi_ext1_gate, ssi_ext2_gate,
 	epit1_ipg_gate, epit1_hf_gate, epit2_ipg_gate, epit2_hf_gate,
+	can_sel, can1_serial_gate, can1_ipg_gate,
 	clk_max
 };
 
@@ -421,8 +423,12 @@ int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk[esdhc4_per_gate] = imx_clk_gate2("esdhc4_per_gate", "esdhc_d_sel", MXC_CCM_CCGR3, 14);
 	clk[usb_phy1_gate] = imx_clk_gate2("usb_phy1_gate", "usb_phy_sel", MXC_CCM_CCGR4, 10);
 	clk[usb_phy2_gate] = imx_clk_gate2("usb_phy2_gate", "usb_phy_sel", MXC_CCM_CCGR4, 12);
-	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "ipg", MXC_CCM_CCGR4, 6);
-	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 8);
+	clk[can_sel] = imx_clk_mux("can_sel", MXC_CCM_CSCMR2, 6, 2,
+				mx53_can_sel, ARRAY_SIZE(mx53_can_sel));
+	clk[can1_serial_gate] = imx_clk_gate2("can1_serial_gate", "can_sel", MXC_CCM_CCGR6, 22);
+	clk[can1_ipg_gate] = imx_clk_gate2("can1_ipg_gate", "ipg", MXC_CCM_CCGR6, 20);
+	clk[can2_serial_gate] = imx_clk_gate2("can2_serial_gate", "can_sel", MXC_CCM_CCGR4, 8);
+	clk[can2_ipg_gate] = imx_clk_gate2("can2_ipg_gate", "ipg", MXC_CCM_CCGR4, 6);
 	clk[i2c3_gate] = imx_clk_gate2("i2c3_gate", "per_root", MXC_CCM_CCGR1, 22);
 
 	for (i = 0; i < ARRAY_SIZE(clk); i++)
@@ -455,6 +461,10 @@ int __init mx53_clocks_init(unsigned long rate_ckil, unsigned long rate_osc,
 	clk_register_clkdev(clk[ssi1_ipg_gate], NULL, "63fcc000.ssi");
 	clk_register_clkdev(clk[ssi2_ipg_gate], NULL, "50014000.ssi");
 	clk_register_clkdev(clk[ssi3_ipg_gate], NULL, "63fd0000.ssi");
+	clk_register_clkdev(clk[can1_ipg_gate], "ipg", "53fc8000.can");
+	clk_register_clkdev(clk[can1_serial_gate], "per", "53fc8000.can");
+	clk_register_clkdev(clk[can2_ipg_gate], "ipg", "53fcc000.can");
+	clk_register_clkdev(clk[can2_serial_gate], "per", "53fcc000.can");
 
 	/* set SDHC root clock to 200MHZ*/
 	clk_set_rate(clk[esdhc_a_podf], 200000000);

arch/arm/mach-lpc32xx/irq.c

@@ -283,21 +283,25 @@ static int lpc32xx_set_irq_type(struct irq_data *d, unsigned int type)
 	case IRQ_TYPE_EDGE_RISING:
 		/* Rising edge sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 1, 1);
+		__irq_set_handler_locked(d->hwirq, handle_edge_irq);
 		break;
 
 	case IRQ_TYPE_EDGE_FALLING:
 		/* Falling edge sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 0, 1);
+		__irq_set_handler_locked(d->hwirq, handle_edge_irq);
 		break;
 
 	case IRQ_TYPE_LEVEL_LOW:
 		/* Low level sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 0, 0);
+		__irq_set_handler_locked(d->hwirq, handle_level_irq);
 		break;
 
 	case IRQ_TYPE_LEVEL_HIGH:
 		/* High level sensitive */
 		__lpc32xx_set_irq_type(d->hwirq, 1, 0);
+		__irq_set_handler_locked(d->hwirq, handle_level_irq);
 		break;
 
 	/* Other modes are not supported */
@@ -305,9 +309,6 @@ static int lpc32xx_set_irq_type(struct irq_data *d, unsigned int type)
 		return -EINVAL;
 	}
 
-	/* Ok to use the level handler for all types */
-	irq_set_handler(d->hwirq, handle_level_irq);
-
 	return 0;
 }
 

arch/arm/mach-lpc32xx/phy3250.c

@@ -37,6 +37,8 @@
 #include <linux/of_irq.h>
 #include <linux/of_platform.h>
 #include <linux/clk.h>
+#include <linux/mtd/lpc32xx_slc.h>
+#include <linux/mtd/lpc32xx_mlc.h>
 
 #include <asm/setup.h>
 #include <asm/mach-types.h>
@@ -223,6 +225,14 @@ static struct mmci_platform_data lpc32xx_mmci_data = {
 	 * gather, and the MMCI driver doesn't do it this way */
 };
 
+static struct lpc32xx_slc_platform_data lpc32xx_slc_data = {
+	.dma_filter = pl08x_filter_id,
+};
+
+static struct lpc32xx_mlc_platform_data lpc32xx_mlc_data = {
+	.dma_filter = pl08x_filter_id,
+};
+
 static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
 	OF_DEV_AUXDATA("arm,pl022", 0x20084000, "dev:ssp0", &lpc32xx_ssp0_data),
 	OF_DEV_AUXDATA("arm,pl022", 0x2008C000, "dev:ssp1", &lpc32xx_ssp1_data),
@@ -230,6 +240,10 @@ static const struct of_dev_auxdata lpc32xx_auxdata_lookup[] __initconst = {
 	OF_DEV_AUXDATA("arm,pl080", 0x31000000, "pl08xdmac", &pl08x_pd),
 	OF_DEV_AUXDATA("arm,pl18x", 0x20098000, "20098000.sd",
 		       &lpc32xx_mmci_data),
+	OF_DEV_AUXDATA("nxp,lpc3220-slc", 0x20020000, "20020000.flash",
+		       &lpc32xx_slc_data),
+	OF_DEV_AUXDATA("nxp,lpc3220-mlc", 0x200a8000, "200a8000.flash",
+		       &lpc32xx_mlc_data),
 	{ }
 };
 
@@ -253,12 +267,6 @@ static void __init lpc3250_machine_init(void)
 
 	of_platform_populate(NULL, of_default_bus_match_table,
 			     lpc32xx_auxdata_lookup, NULL);
-
-	/* Register GPIOs used on this board */
-	if (gpio_request(MMC_PWR_ENABLE_GPIO, "mmc_power_en"))
-		pr_err("Error requesting gpio %u", MMC_PWR_ENABLE_GPIO);
-	else if (gpio_direction_output(MMC_PWR_ENABLE_GPIO, 1))
-		pr_err("Error setting gpio %u to output", MMC_PWR_ENABLE_GPIO);
 }
 
 static char const *lpc32xx_dt_compat[] __initdata = {

arch/arm/mach-omap2/Makefile

@@ -174,6 +174,7 @@ obj-$(CONFIG_SOC_OMAP2430)		+= omap_hwmod_2430_data.o
 obj-$(CONFIG_ARCH_OMAP3)		+= omap_hwmod_2xxx_3xxx_ipblock_data.o
 obj-$(CONFIG_ARCH_OMAP3)		+= omap_hwmod_2xxx_3xxx_interconnect_data.o
 obj-$(CONFIG_ARCH_OMAP3)		+= omap_hwmod_3xxx_data.o
+obj-$(CONFIG_SOC_AM33XX)		+= omap_hwmod_33xx_data.o
 obj-$(CONFIG_ARCH_OMAP4)		+= omap_hwmod_44xx_data.o
 
 # EMU peripherals

arch/arm/mach-omap2/clkt_dpll.c

@@ -211,7 +211,7 @@ void omap2_init_dpll_parent(struct clk *clk)
 		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
 			clk_reparent(clk, dd->clk_bypass);
-	} else if (cpu_is_omap44xx()) {
+	} else if (soc_is_am33xx() || cpu_is_omap44xx()) {
 		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_MNBYPASS)
@@ -257,7 +257,7 @@ u32 omap2_get_dpll_rate(struct clk *clk)
 		if (v == OMAP3XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP3XXX_EN_DPLL_FRBYPASS)
 			return dd->clk_bypass->rate;
-	} else if (cpu_is_omap44xx()) {
+	} else if (soc_is_am33xx() || cpu_is_omap44xx()) {
 		if (v == OMAP4XXX_EN_DPLL_LPBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_FRBYPASS ||
 		    v == OMAP4XXX_EN_DPLL_MNBYPASS)

arch/arm/mach-omap2/clock33xx_data.c

@@ -1027,7 +1027,9 @@ static struct omap_clk am33xx_clks[] = {
 	CLK(NULL,	"cefuse_fck",		&cefuse_fck,	CK_AM33XX),
 	CLK(NULL,	"clkdiv32k_ick",	&clkdiv32k_ick,	CK_AM33XX),
 	CLK(NULL,	"dcan0_fck",		&dcan0_fck,	CK_AM33XX),
+	CLK("481cc000.d_can",	NULL,		&dcan0_fck,	CK_AM33XX),
 	CLK(NULL,	"dcan1_fck",		&dcan1_fck,	CK_AM33XX),
+	CLK("481d0000.d_can",	NULL,		&dcan1_fck,	CK_AM33XX),
 	CLK(NULL,	"debugss_ick",		&debugss_ick,	CK_AM33XX),
 	CLK(NULL,	"pruss_ocp_gclk",	&pruss_ocp_gclk,	CK_AM33XX),
 	CLK("davinci-mcasp.0",  NULL,           &mcasp0_fck,    CK_AM33XX),

arch/arm/mach-omap2/dpll3xxx.c

@@ -311,7 +311,7 @@ static int omap3_noncore_dpll_program(struct clk *clk, u16 m, u8 n, u16 freqsel)
 	 * Set jitter correction. No jitter correction for OMAP4 and 3630
 	 * since freqsel field is no longer present
 	 */
-	if (!cpu_is_omap44xx() && !cpu_is_omap3630()) {
+	if (!soc_is_am33xx() && !cpu_is_omap44xx() && !cpu_is_omap3630()) {
 		v = __raw_readl(dd->control_reg);
 		v &= ~dd->freqsel_mask;
 		v |= freqsel << __ffs(dd->freqsel_mask);
@@ -471,7 +471,7 @@ int omap3_noncore_dpll_set_rate(struct clk *clk, unsigned long rate)
 			return -EINVAL;
 
 		/* No freqsel on OMAP4 and OMAP3630 */
-		if (!cpu_is_omap44xx() && !cpu_is_omap3630()) {
+		if (!soc_is_am33xx() && !cpu_is_omap44xx() && !cpu_is_omap3630()) {
 			freqsel = _omap3_dpll_compute_freqsel(clk,
 						dd->last_rounded_n);
 			if (!freqsel)

arch/arm/mach-omap2/io.c

@@ -524,6 +524,8 @@ void __init am33xx_init_early(void)
 	am33xx_voltagedomains_init();
 	am33xx_powerdomains_init();
 	am33xx_clockdomains_init();
+	am33xx_hwmod_init();
+	omap_hwmod_init_postsetup();
 	am33xx_clk_init();
 }
 #endif

arch/arm/mach-omap2/omap_hwmod.c

@@ -149,8 +149,10 @@
 #include "powerdomain.h"
 #include "cm2xxx_3xxx.h"
 #include "cminst44xx.h"
+#include "cm33xx.h"
 #include "prm2xxx_3xxx.h"
 #include "prm44xx.h"
+#include "prm33xx.h"
 #include "prminst44xx.h"
 #include "mux.h"
 #include "pm.h"
@@ -867,6 +869,26 @@ static void _omap4_enable_module(struct omap_hwmod *oh)
 				   oh->prcm.omap4.clkctrl_offs);
 }
 
+/**
+ * _am33xx_enable_module - enable CLKCTRL modulemode on AM33XX
+ * @oh: struct omap_hwmod *
+ *
+ * Enables the PRCM module mode related to the hwmod @oh.
+ * No return value.
+ */
+static void _am33xx_enable_module(struct omap_hwmod *oh)
+{
+	if (!oh->clkdm || !oh->prcm.omap4.modulemode)
+		return;
+
+	pr_debug("omap_hwmod: %s: %s: %d\n",
+		 oh->name, __func__, oh->prcm.omap4.modulemode);
+
+	am33xx_cm_module_enable(oh->prcm.omap4.modulemode, oh->clkdm->cm_inst,
+				oh->clkdm->clkdm_offs,
+				oh->prcm.omap4.clkctrl_offs);
+}
+
 /**
  * _omap4_wait_target_disable - wait for a module to be disabled on OMAP4
  * @oh: struct omap_hwmod *
@@ -893,6 +915,31 @@ static int _omap4_wait_target_disable(struct omap_hwmod *oh)
 					     oh->prcm.omap4.clkctrl_offs);
 }
 
+/**
+ * _am33xx_wait_target_disable - wait for a module to be disabled on AM33XX
+ * @oh: struct omap_hwmod *
+ *
+ * Wait for a module @oh to enter slave idle.  Returns 0 if the module
+ * does not have an IDLEST bit or if the module successfully enters
+ * slave idle; otherwise, pass along the return value of the
+ * appropriate *_cm*_wait_module_idle() function.
+ */
+static int _am33xx_wait_target_disable(struct omap_hwmod *oh)
+{
+	if (!oh)
+		return -EINVAL;
+
+	if (oh->_int_flags & _HWMOD_NO_MPU_PORT)
+		return 0;
+
+	if (oh->flags & HWMOD_NO_IDLEST)
+		return 0;
+
+	return am33xx_cm_wait_module_idle(oh->clkdm->cm_inst,
+					     oh->clkdm->clkdm_offs,
+					     oh->prcm.omap4.clkctrl_offs);
+}
+
 /**
  * _count_mpu_irqs - count the number of MPU IRQ lines associated with @oh
  * @oh: struct omap_hwmod *oh
@@ -1613,6 +1660,36 @@ static int _omap4_disable_module(struct omap_hwmod *oh)
 	return 0;
 }
 
+/**
+ * _am33xx_disable_module - enable CLKCTRL modulemode on AM33XX
+ * @oh: struct omap_hwmod *
+ *
+ * Disable the PRCM module mode related to the hwmod @oh.
+ * Return EINVAL if the modulemode is not supported and 0 in case of success.
+ */
+static int _am33xx_disable_module(struct omap_hwmod *oh)
+{
+	int v;
+
+	if (!oh->clkdm || !oh->prcm.omap4.modulemode)
+		return -EINVAL;
+
+	pr_debug("omap_hwmod: %s: %s\n", oh->name, __func__);
+
+	am33xx_cm_module_disable(oh->clkdm->cm_inst, oh->clkdm->clkdm_offs,
+				 oh->prcm.omap4.clkctrl_offs);
+
+	if (_are_any_hardreset_lines_asserted(oh))
+		return 0;
+
+	v = _am33xx_wait_target_disable(oh);
+	if (v)
+		pr_warn("omap_hwmod: %s: _wait_target_disable failed\n",
+			oh->name);
+
+	return 0;
+}
+
 /**
  * _ocp_softreset - reset an omap_hwmod via the OCP_SYSCONFIG bit
  * @oh: struct omap_hwmod *
@@ -2548,6 +2625,33 @@ static int _omap4_wait_target_ready(struct omap_hwmod *oh)
 					      oh->prcm.omap4.clkctrl_offs);
 }
 
+/**
+ * _am33xx_wait_target_ready - wait for a module to leave slave idle
+ * @oh: struct omap_hwmod *
+ *
+ * Wait for a module @oh to leave slave idle.  Returns 0 if the module
+ * does not have an IDLEST bit or if the module successfully leaves
+ * slave idle; otherwise, pass along the return value of the
+ * appropriate *_cm*_wait_module_ready() function.
+ */
+static int _am33xx_wait_target_ready(struct omap_hwmod *oh)
+{
+	if (!oh || !oh->clkdm)
+		return -EINVAL;
+
+	if (oh->flags & HWMOD_NO_IDLEST)
+		return 0;
+
+	if (!_find_mpu_rt_port(oh))
+		return 0;
+
+	/* XXX check module SIDLEMODE, hardreset status */
+
+	return am33xx_cm_wait_module_ready(oh->clkdm->cm_inst,
+					      oh->clkdm->clkdm_offs,
+					      oh->prcm.omap4.clkctrl_offs);
+}
+
 /**
  * _omap2_assert_hardreset - call OMAP2 PRM hardreset fn with hwmod args
  * @oh: struct omap_hwmod * to assert hardreset
@@ -2679,6 +2783,72 @@ static int _omap4_is_hardreset_asserted(struct omap_hwmod *oh,
 				oh->prcm.omap4.rstctrl_offs);
 }
 
+/**
+ * _am33xx_assert_hardreset - call AM33XX PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to assert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call am33xx_prminst_assert_hardreset() with parameters extracted
+ * from the hwmod @oh and the hardreset line data @ohri.  Only
+ * intended for use as an soc_ops function pointer.  Passes along the
+ * return value from am33xx_prminst_assert_hardreset().  XXX This
+ * function is scheduled for removal when the PRM code is moved into
+ * drivers/.
+ */
+static int _am33xx_assert_hardreset(struct omap_hwmod *oh,
+				   struct omap_hwmod_rst_info *ohri)
+
+{
+	return am33xx_prm_assert_hardreset(ohri->rst_shift,
+				oh->clkdm->pwrdm.ptr->prcm_offs,
+				oh->prcm.omap4.rstctrl_offs);
+}
+
+/**
+ * _am33xx_deassert_hardreset - call AM33XX PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to deassert hardreset
+ * @ohri: hardreset line data
+ *
+ * Call am33xx_prminst_deassert_hardreset() with parameters extracted
+ * from the hwmod @oh and the hardreset line data @ohri.  Only
+ * intended for use as an soc_ops function pointer.  Passes along the
+ * return value from am33xx_prminst_deassert_hardreset().  XXX This
+ * function is scheduled for removal when the PRM code is moved into
+ * drivers/.
+ */
+static int _am33xx_deassert_hardreset(struct omap_hwmod *oh,
+				     struct omap_hwmod_rst_info *ohri)
+{
+	if (ohri->st_shift)
+		pr_err("omap_hwmod: %s: %s: hwmod data error: OMAP4 does not support st_shift\n",
+		       oh->name, ohri->name);
+
+	return am33xx_prm_deassert_hardreset(ohri->rst_shift,
+				oh->clkdm->pwrdm.ptr->prcm_offs,
+				oh->prcm.omap4.rstctrl_offs,
+				oh->prcm.omap4.rstst_offs);
+}
+
+/**
+ * _am33xx_is_hardreset_asserted - call AM33XX PRM hardreset fn with hwmod args
+ * @oh: struct omap_hwmod * to test hardreset
+ * @ohri: hardreset line data
+ *
+ * Call am33xx_prminst_is_hardreset_asserted() with parameters
+ * extracted from the hwmod @oh and the hardreset line data @ohri.
+ * Only intended for use as an soc_ops function pointer.  Passes along
+ * the return value from am33xx_prminst_is_hardreset_asserted().  XXX
+ * This function is scheduled for removal when the PRM code is moved
+ * into drivers/.
+ */
+static int _am33xx_is_hardreset_asserted(struct omap_hwmod *oh,
+					struct omap_hwmod_rst_info *ohri)
+{
+	return am33xx_prm_is_hardreset_asserted(ohri->rst_shift,
+				oh->clkdm->pwrdm.ptr->prcm_offs,
+				oh->prcm.omap4.rstctrl_offs);
+}
+
 /* Public functions */
 
 u32 omap_hwmod_read(struct omap_hwmod *oh, u16 reg_offs)
@@ -3705,6 +3875,14 @@ void __init omap_hwmod_init(void)
 		soc_ops.deassert_hardreset = _omap4_deassert_hardreset;
 		soc_ops.is_hardreset_asserted = _omap4_is_hardreset_asserted;
 		soc_ops.init_clkdm = _init_clkdm;
+	} else if (soc_is_am33xx()) {
+		soc_ops.enable_module = _am33xx_enable_module;
+		soc_ops.disable_module = _am33xx_disable_module;
+		soc_ops.wait_target_ready = _am33xx_wait_target_ready;
+		soc_ops.assert_hardreset = _am33xx_assert_hardreset;
+		soc_ops.deassert_hardreset = _am33xx_deassert_hardreset;
+		soc_ops.is_hardreset_asserted = _am33xx_is_hardreset_asserted;
+		soc_ops.init_clkdm = _init_clkdm;
 	} else {
 		WARN(1, "omap_hwmod: unknown SoC type\n");
 	}

arch/arm/mach-shmobile/board-kzm9g.c

@@ -763,6 +763,13 @@ static void __init kzm_init(void)
 	platform_add_devices(kzm_devices, ARRAY_SIZE(kzm_devices));
 }
 
+static void kzm9g_restart(char mode, const char *cmd)
+{
+#define RESCNT2 0xe6188020
+	/* Do soft power on reset */
+	writel((1 << 31), RESCNT2);
+}
+
 static const char *kzm9g_boards_compat_dt[] __initdata = {
 	"renesas,kzm9g",
 	NULL,
@@ -777,5 +784,6 @@ DT_MACHINE_START(KZM9G_DT, "kzm9g")
 	.init_machine	= kzm_init,
 	.init_late	= shmobile_init_late,
 	.timer		= &shmobile_timer,
+	.restart	= kzm9g_restart,
 	.dt_compat	= kzm9g_boards_compat_dt,
 MACHINE_END

arch/arm/mach-shmobile/clock-r8a7779.c

@@ -86,11 +86,16 @@ static struct clk div4_clks[DIV4_NR] = {
 				      0x0300, CLK_ENABLE_ON_INIT),
 };
 
-enum { MSTP026, MSTP025, MSTP024, MSTP023, MSTP022, MSTP021,
+enum { MSTP323, MSTP322, MSTP321, MSTP320,
+	MSTP026, MSTP025, MSTP024, MSTP023, MSTP022, MSTP021,
 	MSTP016, MSTP015, MSTP014,
 	MSTP_NR };
 
 static struct clk mstp_clks[MSTP_NR] = {
+	[MSTP323] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR3, 23, 0), /* SDHI0 */
+	[MSTP322] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR3, 22, 0), /* SDHI1 */
+	[MSTP321] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR3, 21, 0), /* SDHI2 */
+	[MSTP320] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR3, 20, 0), /* SDHI3 */
 	[MSTP026] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR0, 26, 0), /* SCIF0 */
 	[MSTP025] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR0, 25, 0), /* SCIF1 */
 	[MSTP024] = SH_CLK_MSTP32(&div4_clks[DIV4_P], MSTPCR0, 24, 0), /* SCIF2 */
@@ -149,6 +154,10 @@ static struct clk_lookup lookups[] = {
 	CLKDEV_DEV_ID("sh-sci.3", &mstp_clks[MSTP023]), /* SCIF3 */
 	CLKDEV_DEV_ID("sh-sci.4", &mstp_clks[MSTP022]), /* SCIF4 */
 	CLKDEV_DEV_ID("sh-sci.5", &mstp_clks[MSTP021]), /* SCIF6 */
+	CLKDEV_DEV_ID("sh_mobile_sdhi.0", &mstp_clks[MSTP323]), /* SDHI0 */
+	CLKDEV_DEV_ID("sh_mobile_sdhi.1", &mstp_clks[MSTP322]), /* SDHI1 */
+	CLKDEV_DEV_ID("sh_mobile_sdhi.2", &mstp_clks[MSTP321]), /* SDHI2 */
+	CLKDEV_DEV_ID("sh_mobile_sdhi.3", &mstp_clks[MSTP320]), /* SDHI3 */
 };
 
 void __init r8a7779_clock_init(void)

arch/arm/mach-shmobile/setup-emev2.c

@@ -356,6 +356,26 @@ static struct platform_device gio4_device = {
 	},
 };
 
+static struct resource pmu_resources[] = {
+	[0] = {
+		.start	= 152,
+		.end	= 152,
+		.flags	= IORESOURCE_IRQ,
+	},
+	[1] = {
+		.start	= 153,
+		.end	= 153,
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device pmu_device = {
+	.name		= "arm-pmu",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(pmu_resources),
+	.resource	= pmu_resources,
+};
+
 static struct platform_device *emev2_early_devices[] __initdata = {
 	&uart0_device,
 	&uart1_device,
@@ -370,6 +390,7 @@ static struct platform_device *emev2_late_devices[] __initdata = {
 	&gio2_device,
 	&gio3_device,
 	&gio4_device,
+	&pmu_device,
 };
 
 void __init emev2_add_standard_devices(void)

arch/arm/mach-shmobile/setup-sh73a0.c

@@ -734,6 +734,26 @@ static struct platform_device mpdma0_device = {
 	},
 };
 
+static struct resource pmu_resources[] = {
+	[0] = {
+		.start	= gic_spi(55),
+		.end	= gic_spi(55),
+		.flags	= IORESOURCE_IRQ,
+	},
+	[1] = {
+		.start	= gic_spi(56),
+		.end	= gic_spi(56),
+		.flags	= IORESOURCE_IRQ,
+	},
+};
+
+static struct platform_device pmu_device = {
+	.name		= "arm-pmu",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(pmu_resources),
+	.resource	= pmu_resources,
+};
+
 static struct platform_device *sh73a0_early_devices[] __initdata = {
 	&scif0_device,
 	&scif1_device,
@@ -757,6 +777,7 @@ static struct platform_device *sh73a0_late_devices[] __initdata = {
 	&i2c4_device,
 	&dma0_device,
 	&mpdma0_device,
+	&pmu_device,
 };
 
 #define SRCR2          0xe61580b0

arch/arm/mach-tegra/Makefile

@@ -12,9 +12,13 @@ obj-y					+= powergate.o
 obj-y					+= apbio.o
 obj-$(CONFIG_CPU_IDLE)			+= cpuidle.o
 obj-$(CONFIG_CPU_IDLE)			+= sleep.o
-obj-$(CONFIG_ARCH_TEGRA_2x_SOC)         += tegra2_clocks.o
+obj-$(CONFIG_ARCH_TEGRA_2x_SOC)         += tegra20_clocks.o
+obj-$(CONFIG_ARCH_TEGRA_2x_SOC)         += tegra20_clocks_data.o
 obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= tegra2_emc.o
+obj-$(CONFIG_ARCH_TEGRA_2x_SOC)		+= sleep-t20.o
 obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= tegra30_clocks.o
+obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= tegra30_clocks_data.o
+obj-$(CONFIG_ARCH_TEGRA_3x_SOC)		+= sleep-t30.o
 obj-$(CONFIG_SMP)			+= platsmp.o headsmp.o
 obj-$(CONFIG_SMP)                       += reset.o
 obj-$(CONFIG_HOTPLUG_CPU)               += hotplug.o

arch/arm/mach-tegra/board-dt-tegra20.c

@@ -70,6 +70,7 @@ struct of_dev_auxdata tegra20_auxdata_lookup[] __initdata = {
 
 static __initdata struct tegra_clk_init_table tegra_dt_clk_init_table[] = {
 	/* name		parent		rate		enabled */
+	{ "uarta",	"pll_p",	216000000,	true },
 	{ "uartd",	"pll_p",	216000000,	true },
 	{ "usbd",	"clk_m",	12000000,	false },
 	{ "usb2",	"clk_m",	12000000,	false },

arch/arm/mach-tegra/clock.h

@@ -2,6 +2,7 @@
  * arch/arm/mach-tegra/include/mach/clock.h
  *
  * Copyright (C) 2010 Google, Inc.
+ * Copyright (c) 2012 NVIDIA CORPORATION.  All rights reserved.
  *
  * Author:
  *	Colin Cross <ccross@google.com>
@@ -20,9 +21,9 @@
 #ifndef __MACH_TEGRA_CLOCK_H
 #define __MACH_TEGRA_CLOCK_H
 
+#include <linux/clk-provider.h>
 #include <linux/clkdev.h>
 #include <linux/list.h>
-#include <linux/spinlock.h>
 
 #include <mach/clk.h>
 
@@ -52,7 +53,8 @@
 #define ENABLE_ON_INIT		(1 << 28)
 #define PERIPH_ON_APB           (1 << 29)
 
-struct clk;
+struct clk_tegra;
+#define to_clk_tegra(_hw) container_of(_hw, struct clk_tegra, hw)
 
 struct clk_mux_sel {
 	struct clk	*input;
@@ -68,47 +70,29 @@ struct clk_pll_freq_table {
 	u8		cpcon;
 };
 
-struct clk_ops {
-	void		(*init)(struct clk *);
-	int		(*enable)(struct clk *);
-	void		(*disable)(struct clk *);
-	int		(*set_parent)(struct clk *, struct clk *);
-	int		(*set_rate)(struct clk *, unsigned long);
-	long		(*round_rate)(struct clk *, unsigned long);
-	void		(*reset)(struct clk *, bool);
-	int		(*clk_cfg_ex)(struct clk *,
-				enum tegra_clk_ex_param, u32);
-};
-
 enum clk_state {
 	UNINITIALIZED = 0,
 	ON,
 	OFF,
 };
 
-struct clk {
+struct clk_tegra {
 	/* node for master clocks list */
 	struct list_head	node;	/* node for list of all clocks */
 	struct clk_lookup	lookup;
+	struct clk_hw		hw;
 
-#ifdef CONFIG_DEBUG_FS
-	struct dentry		*dent;
-#endif
 	bool			set;
-	struct clk_ops		*ops;
-	unsigned long		rate;
+	unsigned long		fixed_rate;
 	unsigned long		max_rate;
 	unsigned long		min_rate;
 	u32			flags;
 	const char		*name;
 
-	u32			refcnt;
 	enum clk_state		state;
-	struct clk		*parent;
 	u32			div;
 	u32			mul;
 
-	const struct clk_mux_sel	*inputs;
 	u32				reg;
 	u32				reg_shift;
 
@@ -144,7 +128,8 @@ struct clk {
 		} shared_bus_user;
 	} u;
 
-	spinlock_t spinlock;
+	void (*reset)(struct clk_hw *, bool);
+	int (*clk_cfg_ex)(struct clk_hw *, enum tegra_clk_ex_param, u32);
 };
 
 struct clk_duplicate {
@@ -159,13 +144,10 @@ struct tegra_clk_init_table {
 	bool enabled;
 };
 
+void tegra_clk_add(struct clk *c);
 void tegra2_init_clocks(void);
 void tegra30_init_clocks(void);
-void clk_init(struct clk *clk);
 struct clk *tegra_get_clock_by_name(const char *name);
-int clk_reparent(struct clk *c, struct clk *parent);
 void tegra_clk_init_from_table(struct tegra_clk_init_table *table);
-unsigned long clk_get_rate_locked(struct clk *c);
-int clk_set_rate_locked(struct clk *c, unsigned long rate);
 
 #endif

arch/arm/mach-tegra/common.c

@@ -34,6 +34,7 @@
 #include "fuse.h"
 #include "pmc.h"
 #include "apbio.h"
+#include "sleep.h"
 
 /*
  * Storage for debug-macro.S's state.
@@ -135,6 +136,7 @@ void __init tegra20_init_early(void)
 	tegra_init_cache(0x331, 0x441);
 	tegra_pmc_init();
 	tegra_powergate_init();
+	tegra20_hotplug_init();
 }
 #endif
 #ifdef CONFIG_ARCH_TEGRA_3x_SOC
@@ -147,11 +149,11 @@ void __init tegra30_init_early(void)
 	tegra_init_cache(0x441, 0x551);
 	tegra_pmc_init();
 	tegra_powergate_init();
+	tegra30_hotplug_init();
 }
 #endif
 
 void __init tegra_init_late(void)
 {
-	tegra_clk_debugfs_init();
 	tegra_powergate_debugfs_init();
 }

arch/arm/mach-tegra/cpu-tegra.c

@@ -49,6 +49,8 @@ static struct cpufreq_frequency_table freq_table[] = {
 #define NUM_CPUS	2
 
 static struct clk *cpu_clk;
+static struct clk *pll_x_clk;
+static struct clk *pll_p_clk;
 static struct clk *emc_clk;
 
 static unsigned long target_cpu_speed[NUM_CPUS];
@@ -71,6 +73,42 @@ static unsigned int tegra_getspeed(unsigned int cpu)
 	return rate;
 }
 
+static int tegra_cpu_clk_set_rate(unsigned long rate)
+{
+	int ret;
+
+	/*
+	 * Take an extra reference to the main pll so it doesn't turn
+	 * off when we move the cpu off of it
+	 */
+	clk_prepare_enable(pll_x_clk);
+
+	ret = clk_set_parent(cpu_clk, pll_p_clk);
+	if (ret) {
+		pr_err("Failed to switch cpu to clock pll_p\n");
+		goto out;
+	}
+
+	if (rate == clk_get_rate(pll_p_clk))
+		goto out;
+
+	ret = clk_set_rate(pll_x_clk, rate);
+	if (ret) {
+		pr_err("Failed to change pll_x to %lu\n", rate);
+		goto out;
+	}
+
+	ret = clk_set_parent(cpu_clk, pll_x_clk);
+	if (ret) {
+		pr_err("Failed to switch cpu to clock pll_x\n");
+		goto out;
+	}
+
+out:
+	clk_disable_unprepare(pll_x_clk);
+	return ret;
+}
+
 static int tegra_update_cpu_speed(unsigned long rate)
 {
 	int ret = 0;
@@ -101,7 +139,7 @@ static int tegra_update_cpu_speed(unsigned long rate)
 	       freqs.old, freqs.new);
 #endif
 
-	ret = clk_set_rate(cpu_clk, freqs.new * 1000);
+	ret = tegra_cpu_clk_set_rate(freqs.new * 1000);
 	if (ret) {
 		pr_err("cpu-tegra: Failed to set cpu frequency to %d kHz\n",
 			freqs.new);
@@ -183,6 +221,14 @@ static int tegra_cpu_init(struct cpufreq_policy *policy)
 	if (IS_ERR(cpu_clk))
 		return PTR_ERR(cpu_clk);
 
+	pll_x_clk = clk_get_sys(NULL, "pll_x");
+	if (IS_ERR(pll_x_clk))
+		return PTR_ERR(pll_x_clk);
+
+	pll_p_clk = clk_get_sys(NULL, "pll_p");
+	if (IS_ERR(pll_p_clk))
+		return PTR_ERR(pll_p_clk);
+
 	emc_clk = clk_get_sys("cpu", "emc");
 	if (IS_ERR(emc_clk)) {
 		clk_put(cpu_clk);

arch/arm/mach-tegra/headsmp.S

@@ -7,17 +7,13 @@
 
 #include "flowctrl.h"
 #include "reset.h"
+#include "sleep.h"
 
 #define APB_MISC_GP_HIDREV	0x804
 #define PMC_SCRATCH41	0x140
 
 #define RESET_DATA(x)	((TEGRA_RESET_##x)*4)
 
-	.macro mov32, reg, val
-	movw	\reg, #:lower16:\val
-	movt	\reg, #:upper16:\val
-	.endm
-
         .section ".text.head", "ax"
 	__CPUINIT
 

arch/arm/mach-tegra/hotplug.c

 /*
- *  linux/arch/arm/mach-realview/hotplug.c
  *
  *  Copyright (C) 2002 ARM Ltd.
  *  All Rights Reserved
+ *  Copyright (c) 2010, 2012 NVIDIA Corporation. All rights reserved.
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License version 2 as
  * published by the Free Software Foundation.
  */
 #include <linux/kernel.h>
-#include <linux/errno.h>
 #include <linux/smp.h>
 
 #include <asm/cacheflush.h>
-#include <asm/cp15.h>
+#include <asm/smp_plat.h>
 
-static inline void cpu_enter_lowpower(void)
-{
-	unsigned int v;
-
-	flush_cache_all();
-	asm volatile(
-	"	mcr	p15, 0, %1, c7, c5, 0\n"
-	"	mcr	p15, 0, %1, c7, c10, 4\n"
-	/*
-	 * Turn off coherency
-	 */
-	"	mrc	p15, 0, %0, c1, c0, 1\n"
-	"	bic	%0, %0, #0x20\n"
-	"	mcr	p15, 0, %0, c1, c0, 1\n"
-	"	mrc	p15, 0, %0, c1, c0, 0\n"
-	"	bic	%0, %0, %2\n"
-	"	mcr	p15, 0, %0, c1, c0, 0\n"
-	  : "=&r" (v)
-	  : "r" (0), "Ir" (CR_C)
-	  : "cc");
-}
-
-static inline void cpu_leave_lowpower(void)
-{
-	unsigned int v;
-
-	asm volatile(
-	"mrc	p15, 0, %0, c1, c0, 0\n"
-	"	orr	%0, %0, %1\n"
-	"	mcr	p15, 0, %0, c1, c0, 0\n"
-	"	mrc	p15, 0, %0, c1, c0, 1\n"
-	"	orr	%0, %0, #0x20\n"
-	"	mcr	p15, 0, %0, c1, c0, 1\n"
-	  : "=&r" (v)
-	  : "Ir" (CR_C)
-	  : "cc");
-}
+#include "sleep.h"
+#include "tegra_cpu_car.h"
 
-static inline void platform_do_lowpower(unsigned int cpu, int *spurious)
-{
-	/*
-	 * there is no power-control hardware on this platform, so all
-	 * we can do is put the core into WFI; this is safe as the calling
-	 * code will have already disabled interrupts
-	 */
-	for (;;) {
-		/*
-		 * here's the WFI
-		 */
-		asm(".word	0xe320f003\n"
-		    :
-		    :
-		    : "memory", "cc");
-
-		/*if (pen_release == cpu) {*/
-			/*
-			 * OK, proper wakeup, we're done
-			 */
-			break;
-		/*}*/
-
-		/*
-		 * Getting here, means that we have come out of WFI without
-		 * having been woken up - this shouldn't happen
-		 *
-		 * Just note it happening - when we're woken, we can report
-		 * its occurrence.
-		 */
-		(*spurious)++;
-	}
-}
+static void (*tegra_hotplug_shutdown)(void);
 
 int platform_cpu_kill(unsigned int cpu)
 {
@@ -99,22 +31,20 @@ int platform_cpu_kill(unsigned int cpu)
  */
 void platform_cpu_die(unsigned int cpu)
 {
-	int spurious = 0;
+	cpu = cpu_logical_map(cpu);
 
-	/*
-	 * we're ready for shutdown now, so do it
-	 */
-	cpu_enter_lowpower();
-	platform_do_lowpower(cpu, &spurious);
+	/* Flush the L1 data cache. */
+	flush_cache_all();
 
-	/*
-	 * bring this CPU back into the world of cache
-	 * coherency, and then restore interrupts
-	 */
-	cpu_leave_lowpower();
+	/* Shut down the current CPU. */
+	tegra_hotplug_shutdown();
+
+	/* Clock gate the CPU */
+	tegra_wait_cpu_in_reset(cpu);
+	tegra_disable_cpu_clock(cpu);
 
-	if (spurious)
-		pr_warn("CPU%u: %u spurious wakeup calls\n", cpu, spurious);
+	/* Should never return here. */
+	BUG();
 }
 
 int platform_cpu_disable(unsigned int cpu)
@@ -125,3 +55,19 @@ int platform_cpu_disable(unsigned int cpu)
 	 */
 	return cpu == 0 ? -EPERM : 0;
 }
+
+#ifdef CONFIG_ARCH_TEGRA_2x_SOC
+extern void tegra20_hotplug_shutdown(void);
+void __init tegra20_hotplug_init(void)
+{
+	tegra_hotplug_shutdown = tegra20_hotplug_shutdown;
+}
+#endif
+
+#ifdef CONFIG_ARCH_TEGRA_3x_SOC
+extern void tegra30_hotplug_shutdown(void);
+void __init tegra30_hotplug_init(void)
+{
+	tegra_hotplug_shutdown = tegra30_hotplug_shutdown;
+}
+#endif

arch/arm/mach-tegra/include/mach/clk.h

@@ -34,7 +34,10 @@ enum tegra_clk_ex_param {
 void tegra_periph_reset_deassert(struct clk *c);
 void tegra_periph_reset_assert(struct clk *c);
 
+#ifndef CONFIG_COMMON_CLK
 unsigned long clk_get_rate_all_locked(struct clk *c);
+#endif
+
 void tegra2_sdmmc_tap_delay(struct clk *c, int delay);
 int tegra_clk_cfg_ex(struct clk *c, enum tegra_clk_ex_param p, u32 setting);
 

arch/arm/mach-tegra/platsmp.c

@@ -31,6 +31,7 @@
 #include "fuse.h"
 #include "flowctrl.h"
 #include "reset.h"
+#include "tegra_cpu_car.h"
 
 extern void tegra_secondary_startup(void);
 
@@ -38,17 +39,6 @@ static void __iomem *scu_base = IO_ADDRESS(TEGRA_ARM_PERIF_BASE);
 
 #define EVP_CPU_RESET_VECTOR \
 	(IO_ADDRESS(TEGRA_EXCEPTION_VECTORS_BASE) + 0x100)
-#define CLK_RST_CONTROLLER_CLK_CPU_CMPLX \
-	(IO_ADDRESS(TEGRA_CLK_RESET_BASE) + 0x4c)
-#define CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET \
-	(IO_ADDRESS(TEGRA_CLK_RESET_BASE) + 0x340)
-#define CLK_RST_CONTROLLER_RST_CPU_CMPLX_CLR \
-	(IO_ADDRESS(TEGRA_CLK_RESET_BASE) + 0x344)
-#define CLK_RST_CONTROLLER_CLK_CPU_CMPLX_CLR \
-	(IO_ADDRESS(TEGRA_CLK_RESET_BASE) + 0x34c)
-
-#define CPU_CLOCK(cpu)	(0x1<<(8+cpu))
-#define CPU_RESET(cpu)	(0x1111ul<<(cpu))
 
 void __cpuinit platform_secondary_init(unsigned int cpu)
 {
@@ -63,13 +53,8 @@ void __cpuinit platform_secondary_init(unsigned int cpu)
 
 static int tegra20_power_up_cpu(unsigned int cpu)
 {
-	u32 reg;
-
 	/* Enable the CPU clock. */
-	reg = readl(CLK_RST_CONTROLLER_CLK_CPU_CMPLX);
-	writel(reg & ~CPU_CLOCK(cpu), CLK_RST_CONTROLLER_CLK_CPU_CMPLX);
-	barrier();
-	reg = readl(CLK_RST_CONTROLLER_CLK_CPU_CMPLX);
+	tegra_enable_cpu_clock(cpu);
 
 	/* Clear flow controller CSR. */
 	flowctrl_write_cpu_csr(cpu, 0);
@@ -79,7 +64,6 @@ static int tegra20_power_up_cpu(unsigned int cpu)
 
 static int tegra30_power_up_cpu(unsigned int cpu)
 {
-	u32 reg;
 	int ret, pwrgateid;
 	unsigned long timeout;
 
@@ -103,8 +87,7 @@ static int tegra30_power_up_cpu(unsigned int cpu)
 	}
 
 	/* CPU partition is powered. Enable the CPU clock. */
-	writel(CPU_CLOCK(cpu), CLK_RST_CONTROLLER_CLK_CPU_CMPLX_CLR);
-	reg = readl(CLK_RST_CONTROLLER_CLK_CPU_CMPLX_CLR);
+	tegra_enable_cpu_clock(cpu);
 	udelay(10);
 
 	/* Remove I/O clamps. */
@@ -128,8 +111,7 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
 	 * via the flow controller). This will have no effect on first boot
 	 * of the CPU since it should already be in reset.
 	 */
-	writel(CPU_RESET(cpu), CLK_RST_CONTROLLER_RST_CPU_CMPLX_SET);
-	dmb();
+	tegra_put_cpu_in_reset(cpu);
 
 	/*
 	 * Unhalt the CPU. If the flow controller was used to power-gate the
@@ -155,8 +137,7 @@ int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
 		goto done;
 
 	/* Take the CPU out of reset. */
-	writel(CPU_RESET(cpu), CLK_RST_CONTROLLER_RST_CPU_CMPLX_CLR);
-	wmb();
+	tegra_cpu_out_of_reset(cpu);
 done:
 	return status;
 }

arch/arm/mach-tegra/sleep.S

@@ -29,36 +29,5 @@
 #include <mach/iomap.h>
 
 #include "flowctrl.h"
+#include "sleep.h"
 
-#define TEGRA_FLOW_CTRL_VIRT (TEGRA_FLOW_CTRL_BASE - IO_PPSB_PHYS \
-					+ IO_PPSB_VIRT)
-
-/* returns the offset of the flow controller halt register for a cpu */
-.macro cpu_to_halt_reg rd, rcpu
-	cmp	\rcpu, #0
-	subne	\rd, \rcpu, #1
-	movne	\rd, \rd, lsl #3
-	addne	\rd, \rd, #0x14
-	moveq	\rd, #0
-.endm
-
-/* returns the offset of the flow controller csr register for a cpu */
-.macro cpu_to_csr_reg rd, rcpu
-	cmp	\rcpu, #0
-	subne	\rd, \rcpu, #1
-	movne	\rd, \rd, lsl #3
-	addne	\rd, \rd, #0x18
-	moveq	\rd, #8
-.endm
-
-/* returns the ID of the current processor */
-.macro cpu_id, rd
-	mrc	p15, 0, \rd, c0, c0, 5
-	and	\rd, \rd, #0xF
-.endm
-
-/* loads a 32-bit value into a register without a data access */
-.macro mov32, reg, val
-	movw	\reg, #:lower16:\val
-	movt	\reg, #:upper16:\val
-.endm

arch/arm/mach-ux500/cache-l2x0.c

@@ -38,7 +38,7 @@ static int __init ux500_l2x0_init(void)
 {
 	u32 aux_val = 0x3e000000;
 
-	if (cpu_is_u8500_family())
+	if (cpu_is_u8500_family() || cpu_is_ux540_family())
 		l2x0_base = __io_address(U8500_L2CC_BASE);
 	else
 		ux500_unknown_soc();

arch/arm/mach-ux500/cpu-db8500.c

@@ -79,7 +79,7 @@ void __init u8500_map_io(void)
 
 	iotable_init(u8500_common_io_desc, ARRAY_SIZE(u8500_common_io_desc));
 
-	if (cpu_is_u9540())
+	if (cpu_is_ux540_family())
 		iotable_init(u9540_io_desc, ARRAY_SIZE(u9540_io_desc));
 	else
 		iotable_init(u8500_io_desc, ARRAY_SIZE(u8500_io_desc));

drivers/irqchip/Makefile

+obj-$(CONFIG_ARCH_BCM2835) += irq-bcm2835.o