powerpc/mpc83xx: Fix usb mux setup for mpc834x

usb0 and usb1 mux settings in the sicrl register were swapped (twice!)
in mpc834x_usb_cfg(), leading to various strange issues with fsl-ehci
and full speed devices.

The USB port config on mpc834x is done using 2 muxes: Port 0 is always
used for MPH port 0, and port 1 can either be used for MPH port 1 or DR
(unless DR uses UTMI phy or OTG, then it uses both ports) - See 8349 RM
figure 1-4..

mpc8349_usb_cfg() had this inverted for the DR, and it also had the bit
positions of the usb0 / usb1 mux settings swapped. It would basically
work if you specified port1 instead of port0 for the MPH controller (and
happened to use ULPI phys), which is what all the 834x dts have done,
even though that configuration is physically invalid.

Instead fix mpc8349_usb_cfg() and adjust the dts files to match reality.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>

arch/powerpc/boot/dts/asp834x-redboot.dts

@@ -167,7 +167,7 @@ usb@22000 {
 			interrupt-parent = <&ipic>;
 			interrupts = <39 0x8>;
 			phy_type = "ulpi";
-			port1;
+			port0;
 		};
 		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
 		usb@23000 {

arch/powerpc/boot/dts/mpc8349emitx.dts

@@ -156,7 +156,7 @@ usb@22000 {
 			interrupt-parent = <&ipic>;
 			interrupts = <39 0x8>;
 			phy_type = "ulpi";
-			port1;
+			port0;
 		};
 
 		usb@23000 {

arch/powerpc/boot/dts/mpc834x_mds.dts

@@ -153,7 +153,7 @@ usb@22000 {
 			interrupt-parent = <&ipic>;
 			interrupts = <39 0x8>;
 			phy_type = "ulpi";
-			port1;
+			port0;
 		};
 		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
 		usb@23000 {

arch/powerpc/boot/dts/sbc8349.dts

@@ -144,7 +144,7 @@ usb@22000 {
 			interrupt-parent = <&ipic>;
 			interrupts = <39 0x8>;
 			phy_type = "ulpi";
-			port1;
+			port0;
 		};
 		/* phy type (ULPI, UTMI, UTMI_WIDE, SERIAL) */
 		usb@23000 {

arch/powerpc/platforms/83xx/mpc83xx.h

@@ -22,8 +22,8 @@
 /* system i/o configuration register low */
 #define MPC83XX_SICRL_OFFS         0x114
 #define MPC834X_SICRL_USB_MASK     0x60000000
-#define MPC834X_SICRL_USB0         0x40000000
-#define MPC834X_SICRL_USB1         0x20000000
+#define MPC834X_SICRL_USB0         0x20000000
+#define MPC834X_SICRL_USB1         0x40000000
 #define MPC831X_SICRL_USB_MASK     0x00000c00
 #define MPC831X_SICRL_USB_ULPI     0x00000800
 #define MPC8315_SICRL_USB_MASK     0x000000fc

arch/powerpc/platforms/83xx/usb.c

@@ -47,25 +47,25 @@ int mpc834x_usb_cfg(void)
 		sccr |= MPC83XX_SCCR_USB_DRCM_11;  /* 1:3 */
 
 		prop = of_get_property(np, "phy_type", NULL);
+		port1_is_dr = 1;
 		if (prop && (!strcmp(prop, "utmi") ||
 					!strcmp(prop, "utmi_wide"))) {
 			sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
 			sicrh |= MPC834X_SICRH_USB_UTMI;
-			port1_is_dr = 1;
+			port0_is_dr = 1;
 		} else if (prop && !strcmp(prop, "serial")) {
 			dr_mode = of_get_property(np, "dr_mode", NULL);
 			if (dr_mode && !strcmp(dr_mode, "otg")) {
 				sicrl |= MPC834X_SICRL_USB0 | MPC834X_SICRL_USB1;
-				port1_is_dr = 1;
+				port0_is_dr = 1;
 			} else {
-				sicrl |= MPC834X_SICRL_USB0;
+				sicrl |= MPC834X_SICRL_USB1;
 			}
 		} else if (prop && !strcmp(prop, "ulpi")) {
-			sicrl |= MPC834X_SICRL_USB0;
+			sicrl |= MPC834X_SICRL_USB1;
 		} else {
 			printk(KERN_WARNING "834x USB PHY type not supported\n");
 		}
-		port0_is_dr = 1;
 		of_node_put(np);
 	}
 	np = of_find_compatible_node(NULL, NULL, "fsl-usb2-mph");