Skip to content

L
linux
Commit b8fa3af2 authored by Paul Gortmaker's avatar Paul Gortmaker Committed by Michael Ellerman
Browse files
Options

powerpc: drop MPC832x_MDS platform support 

This final variant in the e300 family of Modular Development System
(MDS) in this series was actually aimed at feature reduction - things
like floating point and ethernet were removed in order to make for a
lower power and lower cost system.

Like all the MDS systems, it was meant as a vehicle to get the CPU out
early to hardware OEMs so software and board development could take place
in parallel.

These were made in limited numbers and availability preference was given
to partners who were planning to make their own boards.

Given that the whole reason for existence was to assist in enabling new
board designs [not happening for 10+ years], and that they weren't
generally available, and that the hardware wasn't really hobbyist friendly
even for retro computing, it makes sense to retire the support for this
particular platform.
Signed-off-by: default avatarPaul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: default avatarLi Yang <leoyang.li@nxp.com>
[mpe: Drop stale reference to MPC832x_MDS in arch/powerpc/boot/Makefile]
Signed-off-by: default avatarMichael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20230220115913.25811-5-paul.gortmaker@windriver.com
parent aa572079
Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 607 deletions
arch/powerpc/boot/Makefile
View file @ b8fa3af2
...@@ -334,7 +334,6 @@ image-$(CONFIG_PQ2FADS) += cuImage.pq2fads ...@@ -334,7 +334,6 @@ image-$(CONFIG_PQ2FADS) += cuImage.pq2fads
image-$(CONFIG_EP8248E) += dtbImage.ep8248e image-$(CONFIG_EP8248E) += dtbImage.ep8248e
# Board ports in arch/powerpc/platform/83xx/Kconfig # Board ports in arch/powerpc/platform/83xx/Kconfig
image-$(CONFIG_MPC832x_MDS) += cuImage.mpc832x_mds
image-$(CONFIG_MPC832x_RDB) += cuImage.mpc832x_rdb image-$(CONFIG_MPC832x_RDB) += cuImage.mpc832x_rdb
image-$(CONFIG_MPC834x_ITX) += cuImage.mpc8349emitx \ image-$(CONFIG_MPC834x_ITX) += cuImage.mpc8349emitx \
cuImage.mpc8349emitxgp cuImage.mpc8349emitxgp
......
arch/powerpc/boot/dts/mpc832x_mds.dts deleted 100644 → 0
View file @ aa572079
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* MPC8323E EMDS Device Tree Source
*
* Copyright 2006 Freescale Semiconductor Inc.
*
* To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
* this:
*
* 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
* 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
* next to the serial ports.
* 3) Solder a wire from U61-22 to P19K-22.
*
* Note that there's a typo in the schematic. The board labels the last column
* of pins "P19K", but in the schematic, that column is called "P19J". So if
* you're going by the schematic, the pin is called "P19J-K22".
*/
/dts-v1/;
/ {
model = "MPC8323EMDS";
compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
#address-cells = <1>;
#size-cells = <1>;
aliases {
ethernet0 = &enet0;
ethernet1 = &enet1;
serial0 = &serial0;
serial1 = &serial1;
pci0 = &pci0;
};
cpus {
#address-cells = <1>;
#size-cells = <0>;
PowerPC,8323@0 {
device_type = "cpu";
reg = <0x0>;
d-cache-line-size = <32>; // 32 bytes
i-cache-line-size = <32>; // 32 bytes
d-cache-size = <16384>; // L1, 16K
i-cache-size = <16384>; // L1, 16K
timebase-frequency = <0>;
bus-frequency = <0>;
clock-frequency = <0>;
};
};
memory {
device_type = "memory";
reg = <0x00000000 0x08000000>;
};
bcsr@f8000000 {
compatible = "fsl,mpc8323mds-bcsr";
reg = <0xf8000000 0x8000>;
};
soc8323@e0000000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "soc";
compatible = "simple-bus";
ranges = <0x0 0xe0000000 0x00100000>;
reg = <0xe0000000 0x00000200>;
bus-frequency = <132000000>;
wdt@200 {
device_type = "watchdog";
compatible = "mpc83xx_wdt";
reg = <0x200 0x100>;
};
pmc: power@b00 {
compatible = "fsl,mpc8323-pmc", "fsl,mpc8349-pmc";
reg = <0xb00 0x100 0xa00 0x100>;
interrupts = <80 0x8>;
interrupt-parent = <&ipic>;
};
i2c@3000 {
#address-cells = <1>;
#size-cells = <0>;
cell-index = <0>;
compatible = "fsl-i2c";
reg = <0x3000 0x100>;
interrupts = <14 0x8>;
interrupt-parent = <&ipic>;
dfsrr;
rtc@68 {
compatible = "dallas,ds1374";
reg = <0x68>;
};
};
serial0: serial@4500 {
cell-index = <0>;
device_type = "serial";
compatible = "fsl,ns16550", "ns16550";
reg = <0x4500 0x100>;
clock-frequency = <0>;
interrupts = <9 0x8>;
interrupt-parent = <&ipic>;
};
serial1: serial@4600 {
cell-index = <1>;
device_type = "serial";
compatible = "fsl,ns16550", "ns16550";
reg = <0x4600 0x100>;
clock-frequency = <0>;
interrupts = <10 0x8>;
interrupt-parent = <&ipic>;
};
dma@82a8 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,mpc8323-dma", "fsl,elo-dma";
reg = <0x82a8 4>;
ranges = <0 0x8100 0x1a8>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
cell-index = <0>;
dma-channel@0 {
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
reg = <0 0x80>;
cell-index = <0>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@80 {
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
reg = <0x80 0x80>;
cell-index = <1>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@100 {
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
reg = <0x100 0x80>;
cell-index = <2>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
dma-channel@180 {
compatible = "fsl,mpc8323-dma-channel", "fsl,elo-dma-channel";
reg = <0x180 0x28>;
cell-index = <3>;
interrupt-parent = <&ipic>;
interrupts = <71 8>;
};
};
crypto@30000 {
compatible = "fsl,sec2.2", "fsl,sec2.1", "fsl,sec2.0";
reg = <0x30000 0x10000>;
interrupts = <11 0x8>;
interrupt-parent = <&ipic>;
fsl,num-channels = <1>;
fsl,channel-fifo-len = <24>;
fsl,exec-units-mask = <0x4c>;
fsl,descriptor-types-mask = <0x0122003f>;
sleep = <&pmc 0x03000000>;
};
ipic: pic@700 {
interrupt-controller;
#address-cells = <0>;
#interrupt-cells = <2>;
reg = <0x700 0x100>;
device_type = "ipic";
};
par_io@1400 {
reg = <0x1400 0x100>;
device_type = "par_io";
num-ports = <7>;
pio3: ucc_pin@3 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
3 4 3 0 2 0 /* MDIO */
3 5 1 0 2 0 /* MDC */
0 13 2 0 1 0 /* RX_CLK (CLK9) */
3 24 2 0 1 0 /* TX_CLK (CLK10) */
1 0 1 0 1 0 /* TxD0 */
1 1 1 0 1 0 /* TxD1 */
1 2 1 0 1 0 /* TxD2 */
1 3 1 0 1 0 /* TxD3 */
1 4 2 0 1 0 /* RxD0 */
1 5 2 0 1 0 /* RxD1 */
1 6 2 0 1 0 /* RxD2 */
1 7 2 0 1 0 /* RxD3 */
1 8 2 0 1 0 /* RX_ER */
1 9 1 0 1 0 /* TX_ER */
1 10 2 0 1 0 /* RX_DV */
1 11 2 0 1 0 /* COL */
1 12 1 0 1 0 /* TX_EN */
1 13 2 0 1 0>; /* CRS */
};
pio4: ucc_pin@4 {
pio-map = <
/* port pin dir open_drain assignment has_irq */
3 31 2 0 1 0 /* RX_CLK (CLK7) */
3 6 2 0 1 0 /* TX_CLK (CLK8) */
1 18 1 0 1 0 /* TxD0 */
1 19 1 0 1 0 /* TxD1 */
1 20 1 0 1 0 /* TxD2 */
1 21 1 0 1 0 /* TxD3 */
1 22 2 0 1 0 /* RxD0 */
1 23 2 0 1 0 /* RxD1 */
1 24 2 0 1 0 /* RxD2 */
1 25 2 0 1 0 /* RxD3 */
1 26 2 0 1 0 /* RX_ER */
1 27 1 0 1 0 /* TX_ER */
1 28 2 0 1 0 /* RX_DV */
1 29 2 0 1 0 /* COL */
1 30 1 0 1 0 /* TX_EN */
1 31 2 0 1 0>; /* CRS */
};
pio5: ucc_pin@5 {
pio-map = <
/*
* open has
* port pin dir drain sel irq
*/
2 0 1 0 2 0 /* TxD5 */
2 8 2 0 2 0 /* RxD5 */
2 29 2 0 0 0 /* CTS5 */
2 31 1 0 2 0 /* RTS5 */
2 24 2 0 0 0 /* CD */
>;
};
};
};
qe@e0100000 {
#address-cells = <1>;
#size-cells = <1>;
device_type = "qe";
compatible = "fsl,qe";
ranges = <0x0 0xe0100000 0x00100000>;
reg = <0xe0100000 0x480>;
brg-frequency = <0>;
bus-frequency = <198000000>;
fsl,qe-num-riscs = <1>;
fsl,qe-num-snums = <28>;
muram@10000 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "fsl,qe-muram", "fsl,cpm-muram";
ranges = <0x0 0x00010000 0x00004000>;
data-only@0 {
compatible = "fsl,qe-muram-data",
"fsl,cpm-muram-data";
reg = <0x0 0x4000>;
};
};
spi@4c0 {
cell-index = <0>;
compatible = "fsl,spi";
reg = <0x4c0 0x40>;
interrupts = <2>;
interrupt-parent = <&qeic>;
mode = "cpu";
};
spi@500 {
cell-index = <1>;
compatible = "fsl,spi";
reg = <0x500 0x40>;
interrupts = <1>;
interrupt-parent = <&qeic>;
mode = "cpu";
};
usb@6c0 {
compatible = "qe_udc";
reg = <0x6c0 0x40 0x8b00 0x100>;
interrupts = <11>;
interrupt-parent = <&qeic>;
mode = "slave";
};
enet0: ucc@2200 {
device_type = "network";
compatible = "ucc_geth";
cell-index = <3>;
reg = <0x2200 0x200>;
interrupts = <34>;
interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "clk9";
tx-clock-name = "clk10";
phy-handle = <&phy3>;
pio-handle = <&pio3>;
};
enet1: ucc@3200 {
device_type = "network";
compatible = "ucc_geth";
cell-index = <4>;
reg = <0x3200 0x200>;
interrupts = <35>;
interrupt-parent = <&qeic>;
local-mac-address = [ 00 00 00 00 00 00 ];
rx-clock-name = "clk7";
tx-clock-name = "clk8";
phy-handle = <&phy4>;
pio-handle = <&pio4>;
};
ucc@2400 {
device_type = "serial";
compatible = "ucc_uart";
cell-index = <5>; /* The UCC number, 1-7*/
port-number = <0>; /* Which ttyQEx device */
soft-uart; /* We need Soft-UART */
reg = <0x2400 0x200>;
interrupts = <40>; /* From Table 18-12 */
interrupt-parent = < &qeic >;
/*
* For Soft-UART, we need to set TX to 1X, which
* means specifying separate clock sources.
*/
rx-clock-name = "brg5";
tx-clock-name = "brg6";
pio-handle = < &pio5 >;
};
mdio@2320 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0x2320 0x18>;
compatible = "fsl,ucc-mdio";
phy3: ethernet-phy@3 {
interrupt-parent = <&ipic>;
interrupts = <17 0x8>;
reg = <0x3>;
};
phy4: ethernet-phy@4 {
interrupt-parent = <&ipic>;
interrupts = <18 0x8>;
reg = <0x4>;
};
};
qeic: interrupt-controller@80 {
interrupt-controller;
compatible = "fsl,qe-ic";
#address-cells = <0>;
#interrupt-cells = <1>;
reg = <0x80 0x80>;
big-endian;
interrupts = <32 0x8 33 0x8>; //high:32 low:33
interrupt-parent = <&ipic>;
};
};
pci0: pci@e0008500 {
interrupt-map-mask = <0xf800 0x0 0x0 0x7>;
interrupt-map = <
/* IDSEL 0x11 AD17 */
0x8800 0x0 0x0 0x1 &ipic 20 0x8
0x8800 0x0 0x0 0x2 &ipic 21 0x8
0x8800 0x0 0x0 0x3 &ipic 22 0x8
0x8800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x12 AD18 */
0x9000 0x0 0x0 0x1 &ipic 22 0x8
0x9000 0x0 0x0 0x2 &ipic 23 0x8
0x9000 0x0 0x0 0x3 &ipic 20 0x8
0x9000 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x13 AD19 */
0x9800 0x0 0x0 0x1 &ipic 23 0x8
0x9800 0x0 0x0 0x2 &ipic 20 0x8
0x9800 0x0 0x0 0x3 &ipic 21 0x8
0x9800 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x15 AD21*/
0xa800 0x0 0x0 0x1 &ipic 20 0x8
0xa800 0x0 0x0 0x2 &ipic 21 0x8
0xa800 0x0 0x0 0x3 &ipic 22 0x8
0xa800 0x0 0x0 0x4 &ipic 23 0x8
/* IDSEL 0x16 AD22*/
0xb000 0x0 0x0 0x1 &ipic 23 0x8
0xb000 0x0 0x0 0x2 &ipic 20 0x8
0xb000 0x0 0x0 0x3 &ipic 21 0x8
0xb000 0x0 0x0 0x4 &ipic 22 0x8
/* IDSEL 0x17 AD23*/
0xb800 0x0 0x0 0x1 &ipic 22 0x8
0xb800 0x0 0x0 0x2 &ipic 23 0x8
0xb800 0x0 0x0 0x3 &ipic 20 0x8
0xb800 0x0 0x0 0x4 &ipic 21 0x8
/* IDSEL 0x18 AD24*/
0xc000 0x0 0x0 0x1 &ipic 21 0x8
0xc000 0x0 0x0 0x2 &ipic 22 0x8
0xc000 0x0 0x0 0x3 &ipic 23 0x8
0xc000 0x0 0x0 0x4 &ipic 20 0x8>;
interrupt-parent = <&ipic>;
interrupts = <66 0x8>;
bus-range = <0x0 0x0>;
ranges = <0x02000000 0x0 0x90000000 0x90000000 0x0 0x10000000
0x42000000 0x0 0x80000000 0x80000000 0x0 0x10000000
0x01000000 0x0 0x00000000 0xd0000000 0x0 0x00100000>;
clock-frequency = <0>;
#interrupt-cells = <1>;
#size-cells = <2>;
#address-cells = <3>;
reg = <0xe0008500 0x100 /* internal registers */
0xe0008300 0x8>; /* config space access registers */
compatible = "fsl,mpc8349-pci";
device_type = "pci";
sleep = <&pmc 0x00010000>;
};
};
arch/powerpc/configs/83xx/mpc832x_mds_defconfig deleted 100644 → 0
View file @ aa572079
CONFIG_SYSVIPC=y
CONFIG_NO_HZ=y
CONFIG_HIGH_RES_TIMERS=y
CONFIG_LOG_BUF_SHIFT=14
CONFIG_BLK_DEV_INITRD=y
CONFIG_EXPERT=y
# CONFIG_KALLSYMS is not set
CONFIG_MODULES=y
CONFIG_MODULE_UNLOAD=y
# CONFIG_BLK_DEV_BSG is not set
CONFIG_PARTITION_ADVANCED=y
# CONFIG_MSDOS_PARTITION is not set
# CONFIG_PPC_CHRP is not set
# CONFIG_PPC_PMAC is not set
CONFIG_PPC_83xx=y
CONFIG_MPC832x_MDS=y
CONFIG_MATH_EMULATION=y
CONFIG_PCI=y
CONFIG_NET=y
CONFIG_PACKET=y
CONFIG_UNIX=y
CONFIG_INET=y
CONFIG_IP_MULTICAST=y
CONFIG_IP_PNP=y
CONFIG_IP_PNP_DHCP=y
CONFIG_IP_PNP_BOOTP=y
CONFIG_SYN_COOKIES=y
# CONFIG_IPV6 is not set
# CONFIG_FW_LOADER is not set
CONFIG_BLK_DEV_LOOP=y
CONFIG_BLK_DEV_RAM=y
CONFIG_BLK_DEV_RAM_SIZE=32768
CONFIG_SCSI=y
CONFIG_NETDEVICES=y
CONFIG_UCC_GETH=y
CONFIG_DAVICOM_PHY=y
# CONFIG_INPUT_KEYBOARD is not set
# CONFIG_INPUT_MOUSE is not set
# CONFIG_SERIO is not set
# CONFIG_VT is not set
CONFIG_SERIAL_8250=y
CONFIG_SERIAL_8250_CONSOLE=y
CONFIG_HW_RANDOM=y
CONFIG_I2C=y
CONFIG_I2C_CHARDEV=y
CONFIG_I2C_MPC=y
CONFIG_WATCHDOG=y
CONFIG_RTC_CLASS=y
CONFIG_RTC_DRV_DS1374=y
CONFIG_QUICC_ENGINE=y
CONFIG_EXT2_FS=y
CONFIG_EXT4_FS=y
CONFIG_PROC_KCORE=y
CONFIG_TMPFS=y
CONFIG_NFS_FS=y
CONFIG_NFS_V4=y
CONFIG_ROOT_NFS=y
CONFIG_CRYPTO_ECB=m
CONFIG_CRYPTO_PCBC=m
arch/powerpc/configs/mpc83xx_defconfig
View file @ b8fa3af2
...@@ -11,7 +11,6 @@ CONFIG_PARTITION_ADVANCED=y ...@@ -11,7 +11,6 @@ CONFIG_PARTITION_ADVANCED=y
# CONFIG_PPC_PMAC is not set # CONFIG_PPC_PMAC is not set
CONFIG_PPC_83xx=y CONFIG_PPC_83xx=y
CONFIG_MPC831x_RDB=y CONFIG_MPC831x_RDB=y
CONFIG_MPC832x_MDS=y
CONFIG_MPC832x_RDB=y CONFIG_MPC832x_RDB=y
CONFIG_MPC834x_ITX=y CONFIG_MPC834x_ITX=y
CONFIG_MPC836x_RDK=y CONFIG_MPC836x_RDK=y
......
arch/powerpc/configs/ppc6xx_defconfig
View file @ b8fa3af2
...@@ -44,7 +44,6 @@ CONFIG_EP8248E=y ...@@ -44,7 +44,6 @@ CONFIG_EP8248E=y
CONFIG_MGCOGE=y CONFIG_MGCOGE=y
CONFIG_PPC_83xx=y CONFIG_PPC_83xx=y
CONFIG_MPC831x_RDB=y CONFIG_MPC831x_RDB=y
CONFIG_MPC832x_MDS=y
CONFIG_MPC832x_RDB=y CONFIG_MPC832x_RDB=y
CONFIG_MPC834x_ITX=y CONFIG_MPC834x_ITX=y
CONFIG_MPC836x_RDK=y CONFIG_MPC836x_RDK=y
......
arch/powerpc/platforms/83xx/Kconfig
View file @ b8fa3af2
...@@ -25,13 +25,6 @@ config MPC831x_RDB ...@@ -25,13 +25,6 @@ config MPC831x_RDB
help help
This option enables support for the MPC8313 RDB and MPC8315 RDB boards. This option enables support for the MPC8313 RDB and MPC8315 RDB boards.
config MPC832x_MDS
bool "Freescale MPC832x MDS"
select DEFAULT_UIMAGE
select PPC_MPC832x
help
This option enables support for the MPC832x MDS evaluation board.
config MPC832x_RDB config MPC832x_RDB
bool "Freescale MPC832x RDB" bool "Freescale MPC832x RDB"
select DEFAULT_UIMAGE select DEFAULT_UIMAGE
......
arch/powerpc/platforms/83xx/Makefile
View file @ b8fa3af2
...@@ -10,7 +10,6 @@ obj-$(CONFIG_MPC831x_RDB) += mpc831x_rdb.o ...@@ -10,7 +10,6 @@ obj-$(CONFIG_MPC831x_RDB) += mpc831x_rdb.o
obj-$(CONFIG_MPC832x_RDB) += mpc832x_rdb.o obj-$(CONFIG_MPC832x_RDB) += mpc832x_rdb.o
obj-$(CONFIG_MPC834x_ITX) += mpc834x_itx.o obj-$(CONFIG_MPC834x_ITX) += mpc834x_itx.o
obj-$(CONFIG_MPC836x_RDK) += mpc836x_rdk.o obj-$(CONFIG_MPC836x_RDK) += mpc836x_rdk.o
obj-$(CONFIG_MPC832x_MDS) += mpc832x_mds.o
obj-$(CONFIG_MPC837x_RDB) += mpc837x_rdb.o obj-$(CONFIG_MPC837x_RDB) += mpc837x_rdb.o
obj-$(CONFIG_ASP834x) += asp834x.o obj-$(CONFIG_ASP834x) += asp834x.o
obj-$(CONFIG_KMETER1) += km83xx.o obj-$(CONFIG_KMETER1) += km83xx.o
arch/powerpc/platforms/83xx/mpc832x_mds.c deleted 100644 → 0
View file @ aa572079
// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright 2006 Freescale Semiconductor, Inc. All rights reserved.
*
* Description:
* MPC832xE MDS board specific routines.
*/
#include <linux/stddef.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/reboot.h>
#include <linux/pci.h>
#include <linux/kdev_t.h>
#include <linux/major.h>
#include <linux/console.h>
#include <linux/delay.h>
#include <linux/seq_file.h>
#include <linux/root_dev.h>
#include <linux/initrd.h>
#include <linux/of_platform.h>
#include <linux/of_device.h>
#include <linux/atomic.h>
#include <asm/time.h>
#include <asm/io.h>
#include <asm/machdep.h>
#include <asm/ipic.h>
#include <asm/irq.h>
#include <asm/udbg.h>
#include <sysdev/fsl_soc.h>
#include <sysdev/fsl_pci.h>
#include <soc/fsl/qe/qe.h>
#include "mpc83xx.h"
#undef DEBUG
#ifdef DEBUG
#define DBG(fmt...) udbg_printf(fmt)
#else
#define DBG(fmt...)
#endif
/* ************************************************************************
*
* Setup the architecture
*
*/
static void __init mpc832x_sys_setup_arch(void)
{
struct device_node *np;
u8 __iomem *bcsr_regs = NULL;
mpc83xx_setup_arch();
/* Map BCSR area */
np = of_find_node_by_name(NULL, "bcsr");
if (np) {
struct resource res;
of_address_to_resource(np, 0, &res);
bcsr_regs = ioremap(res.start, resource_size(&res));
of_node_put(np);
}
#ifdef CONFIG_QUICC_ENGINE
if ((np = of_find_node_by_name(NULL, "par_io")) != NULL) {
par_io_init(np);
of_node_put(np);
for_each_node_by_name(np, "ucc")
par_io_of_config(np);
}
if ((np = of_find_compatible_node(NULL, "network", "ucc_geth"))
!= NULL){
/* Reset the Ethernet PHYs */
#define BCSR8_FETH_RST 0x50
clrbits8(&bcsr_regs[8], BCSR8_FETH_RST);
udelay(1000);
setbits8(&bcsr_regs[8], BCSR8_FETH_RST);
iounmap(bcsr_regs);
of_node_put(np);
}
#endif /* CONFIG_QUICC_ENGINE */
}
machine_device_initcall(mpc832x_mds, mpc83xx_declare_of_platform_devices);
define_machine(mpc832x_mds) {
.name = "MPC832x MDS",
.compatible = "MPC832xMDS",
.setup_arch = mpc832x_sys_setup_arch,
.discover_phbs = mpc83xx_setup_pci,
.init_IRQ = mpc83xx_ipic_init_IRQ,
.get_irq = ipic_get_irq,
.restart = mpc83xx_restart,
.time_init = mpc83xx_time_init,
.progress = udbg_progress,
};
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7