Merge bk://ppc.bkbits.net/for-linus-ppc

into home.transmeta.com:/home/torvalds/v2.5/linux

arch/ppc/4xx_io/Config.in

+#
+# MPC4xx driver options
+#
+mainmenu_option next_comment
+
+comment 'MPC4xx Driver Options'
+
+if [ "$CONFIG_STB03xxx" = "y" ]; then
+   bool 'STB IR Keyboard' CONFIG_STB_KB
+   bool 'SICC Serial port' CONFIG_SERIAL_SICC
+   if [ "$CONFIG_SERIAL_SICC" = "y" -a "$CONFIG_UART0_TTYS1" = "y" ]; then
+      define_bool CONFIG_UART1_DFLT_CONSOLE y	
+      define_bool CONFIG_SERIAL_SICC_CONSOLE y
+   fi
+fi
+endmenu

arch/ppc/4xx_io/Makefile

+#
+# Makefile for the linux MPC4xx ppc-specific parts 
+#
+
+O_TARGET 		:= 4xx_io.o
+
+#obj-y			:=
+
+obj-$(CONFIG_STB_KB)			+= stb_kb.o
+obj-$(CONFIG_SERIAL_SICC)		+= serial_sicc.o
+ 
+include $(TOPDIR)/Rules.make

arch/ppc/4xx_io/stb_kb.c

+/*
+ *  arch/ppc/4xx_io/stb_kb.c
+ *
+ *  This file is subject to the terms and conditions of the GNU General Public
+ *  License. See the file COPYING in the main directory of this archive for
+ *  more details.
+ */
+#include <linux/config.h>
+
+#include <linux/spinlock.h>
+#include <linux/sched.h>
+#include <linux/interrupt.h>
+#include <linux/tty.h>
+#include <linux/mm.h>
+#include <linux/signal.h>
+#include <linux/init.h>
+#include <linux/kbd_ll.h>
+#include <linux/delay.h>
+#include <linux/random.h>
+#include <linux/poll.h>
+#include <linux/miscdevice.h>
+#include <linux/malloc.h>
+#include <linux/kbd_kern.h>
+
+/* the following are borrowed from pc_keyb.c, thanks to those involved! */
+/*
+ * Translation of escaped scancodes to keycodes.
+ * This is now user-settable.
+ * The keycodes 1-88,96-111,119 are fairly standard, and
+ * should probably not be changed - changing might confuse X.
+ * X also interprets scancode 0x5d (KEY_Begin).
+ *
+ * For 1-88 keycode equals scancode.
+ */
+
+#define E0_KPENTER 96
+#define E0_RCTRL   97
+#define E0_KPSLASH 98
+#define E0_PRSCR   99
+#define E0_RALT    100
+#define E0_BREAK   101  /* (control-pause) */
+#define E0_HOME    102
+#define E0_UP      103
+#define E0_PGUP    104
+#define E0_LEFT    105
+#define E0_RIGHT   106
+#define E0_END     107
+#define E0_DOWN    108
+#define E0_PGDN    109
+#define E0_INS     110
+#define E0_DEL     111
+
+#define E1_PAUSE   119
+
+/*
+ * The keycodes below are randomly located in 89-95,112-118,120-127.
+ * They could be thrown away (and all occurrences below replaced by 0),
+ * but that would force many users to use the `setkeycodes' utility, where
+ * they needed not before. It does not matter that there are duplicates, as
+ * long as no duplication occurs for any single keyboard.
+ */
+#define SC_LIM 89
+
+#define FOCUS_PF1 85           /* actual code! */
+#define FOCUS_PF2 89
+#define FOCUS_PF3 90
+#define FOCUS_PF4 91
+#define FOCUS_PF5 92
+#define FOCUS_PF6 93
+#define FOCUS_PF7 94
+#define FOCUS_PF8 95
+#define FOCUS_PF9 120
+#define FOCUS_PF10 121
+#define FOCUS_PF11 122
+#define FOCUS_PF12 123
+
+#define JAP_86     124
+/* tfj@olivia.ping.dk:
+ * The four keys are located over the numeric keypad, and are
+ * labelled A1-A4. It's an rc930 keyboard, from
+ * Regnecentralen/RC International, Now ICL.
+ * Scancodes: 59, 5a, 5b, 5c.
+ */
+#define RGN1 124
+#define RGN2 125
+#define RGN3 126
+#define RGN4 127
+
+static unsigned char high_keys[128 - SC_LIM] = {
+  RGN1, RGN2, RGN3, RGN4, 0, 0, 0,                   /* 0x59-0x5f */
+  0, 0, 0, 0, 0, 0, 0, 0,                            /* 0x60-0x67 */
+  0, 0, 0, 0, 0, FOCUS_PF11, 0, FOCUS_PF12,          /* 0x68-0x6f */
+  0, 0, 0, FOCUS_PF2, FOCUS_PF9, 0, 0, FOCUS_PF3,    /* 0x70-0x77 */
+  FOCUS_PF4, FOCUS_PF5, FOCUS_PF6, FOCUS_PF7,        /* 0x78-0x7b */
+  FOCUS_PF8, JAP_86, FOCUS_PF10, 0                   /* 0x7c-0x7f */
+};
+
+/* BTC */
+#define E0_MACRO   112
+/* LK450 */
+#define E0_F13     113
+#define E0_F14     114
+#define E0_HELP    115
+#define E0_DO      116
+#define E0_F17     117
+#define E0_KPMINPLUS 118
+/*
+ * My OmniKey generates e0 4c for  the "OMNI" key and the
+ * right alt key does nada. [kkoller@nyx10.cs.du.edu]
+ */
+#define E0_OK	124
+/*
+ * New microsoft keyboard is rumoured to have
+ * e0 5b (left window button), e0 5c (right window button),
+ * e0 5d (menu button). [or: LBANNER, RBANNER, RMENU]
+ * [or: Windows_L, Windows_R, TaskMan]
+ */
+#define E0_MSLW	125
+#define E0_MSRW	126
+#define E0_MSTM	127
+
+static unsigned char e0_keys[128] = {
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x00-0x07 */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x08-0x0f */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x10-0x17 */
+  0, 0, 0, 0, E0_KPENTER, E0_RCTRL, 0, 0,	      /* 0x18-0x1f */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x20-0x27 */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x28-0x2f */
+  0, 0, 0, 0, 0, E0_KPSLASH, 0, E0_PRSCR,	      /* 0x30-0x37 */
+  E0_RALT, 0, 0, 0, 0, E0_F13, E0_F14, E0_HELP,	      /* 0x38-0x3f */
+  E0_DO, E0_F17, 0, 0, 0, 0, E0_BREAK, E0_HOME,	      /* 0x40-0x47 */
+  E0_UP, E0_PGUP, 0, E0_LEFT, E0_OK, E0_RIGHT, E0_KPMINPLUS, E0_END,/* 0x48-0x4f */
+  E0_DOWN, E0_PGDN, E0_INS, E0_DEL, 0, 0, 0, 0,	      /* 0x50-0x57 */
+  0, 0, 0, E0_MSLW, E0_MSRW, E0_MSTM, 0, 0,	      /* 0x58-0x5f */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x60-0x67 */
+  0, 0, 0, 0, 0, 0, 0, E0_MACRO,		      /* 0x68-0x6f */
+  0, 0, 0, 0, 0, 0, 0, 0,			      /* 0x70-0x77 */
+  0, 0, 0, 0, 0, 0, 0, 0			      /* 0x78-0x7f */
+};
+
+void __init rawirkbd_init_hw(void) {
+
+}
+/*
+int rawirkbd_setkeycode(unsigned int scancode, unsigned int keycode)
+{
+	return -EINVAL;
+}
+
+int rawirkbd_getkeycode(unsigned int scancode)
+{
+	return -EINVAL;
+}
+*/
+
+int rawirkbd_setkeycode(unsigned int scancode, unsigned int keycode)
+{
+	if (scancode < SC_LIM || scancode > 255 || keycode > 127)
+	  return -EINVAL;
+	if (scancode < 128)
+	  high_keys[scancode - SC_LIM] = keycode;
+	else
+	  e0_keys[scancode - 128] = keycode;
+	return 0;
+}
+
+int rawirkbd_getkeycode(unsigned int scancode)
+{
+	return
+	  (scancode < SC_LIM || scancode > 255) ? -EINVAL :
+	  (scancode < 128) ? high_keys[scancode - SC_LIM] :
+	    e0_keys[scancode - 128];
+}
+
+int rawirkbd_translate(unsigned char scancode, unsigned char *keycode,
+		    char raw_mode)
+{
+	static int prev_scancode = 0;
+
+	/* special prefix scancodes.. */
+	if (scancode == 0xe0 || scancode == 0xe1) {
+		prev_scancode = scancode;
+		return 0;
+	}
+
+	/* 0xFF is sent by a few keyboards, ignore it. 0x00 is error */
+	if (scancode == 0x00 || scancode == 0xff) {
+		prev_scancode = 0;
+		return 0;
+	}
+
+	scancode &= 0x7f;
+
+	if (prev_scancode) {
+	  /*
+	   * usually it will be 0xe0, but a Pause key generates
+	   * e1 1d 45 e1 9d c5 when pressed, and nothing when released
+	   */
+	  if (prev_scancode != 0xe0) {
+	      if (prev_scancode == 0xe1 && scancode == 0x1d) {
+		  prev_scancode = 0x100;
+		  return 0;
+	      } else if (prev_scancode == 0x100 && scancode == 0x45) {
+		  *keycode = E1_PAUSE;
+		  prev_scancode = 0;
+	      } else {
+#ifdef KBD_REPORT_UNKN
+		  if (!raw_mode)
+		    printk(KERN_INFO "keyboard: unknown e1 escape sequence\n");
+#endif
+		  prev_scancode = 0;
+		  return 0;
+	      }
+	  } else {
+	      prev_scancode = 0;
+	      /*
+	       *  The keyboard maintains its own internal caps lock and
+	       *  num lock statuses. In caps lock mode E0 AA precedes make
+	       *  code and E0 2A follows break code. In num lock mode,
+	       *  E0 2A precedes make code and E0 AA follows break code.
+	       *  We do our own book-keeping, so we will just ignore these.
+	       */
+	      /*
+	       *  For my keyboard there is no caps lock mode, but there are
+	       *  both Shift-L and Shift-R modes. The former mode generates
+	       *  E0 2A / E0 AA pairs, the latter E0 B6 / E0 36 pairs.
+	       *  So, we should also ignore the latter. - aeb@cwi.nl
+	       */
+	      if (scancode == 0x2a || scancode == 0x36)
+		return 0;
+
+	      if (e0_keys[scancode])
+		*keycode = e0_keys[scancode];
+	      else {
+#ifdef KBD_REPORT_UNKN
+		  if (!raw_mode)
+		    printk(KERN_INFO "keyboard: unknown scancode e0 %02x\n",
+			   scancode);
+#endif
+		  return 0;
+	      }
+	  }
+	} else if (scancode >= SC_LIM) {
+	    /* This happens with the FOCUS 9000 keyboard
+	       Its keys PF1..PF12 are reported to generate
+	       55 73 77 78 79 7a 7b 7c 74 7e 6d 6f
+	       Moreover, unless repeated, they do not generate
+	       key-down events, so we have to zero up_flag below */
+	    /* Also, Japanese 86/106 keyboards are reported to
+	       generate 0x73 and 0x7d for \ - and \ | respectively. */
+	    /* Also, some Brazilian keyboard is reported to produce
+	       0x73 and 0x7e for \ ? and KP-dot, respectively. */
+
+	  *keycode = high_keys[scancode - SC_LIM];
+
+	  if (!*keycode) {
+	      if (!raw_mode) {
+#ifdef KBD_REPORT_UNKN
+		  printk(KERN_INFO "keyboard: unrecognized scancode (%02x)"
+			 " - ignored\n", scancode);
+#endif
+	      }
+	      return 0;
+	  }
+ 	} else
+	  *keycode = scancode;
+ 	return 1;
+}
+
+char rawirkbd_unexpected_up(unsigned char keycode)
+{
+	/* unexpected, but this can happen: maybe this was a key release for a
+	   FOCUS 9000 PF key; if we want to see it, we have to clear up_flag */
+	if (keycode >= SC_LIM || keycode == 85)
+	    return 0;
+	else
+	    return 0200;
+}
+
+#include <asm/machdep.h>
+
+void redwood_irkb_init(void)
+{
+	extern struct machdep_calls ppc_md;
+
+	ppc_md.kbd_setkeycode           = rawirkbd_setkeycode;
+	ppc_md.kbd_getkeycode           = rawirkbd_getkeycode;
+	ppc_md.kbd_translate            = rawirkbd_translate;
+	ppc_md.kbd_unexpected_up        = rawirkbd_unexpected_up;
+	ppc_md.kbd_leds                 = NULL; /*rawirkbd_leds;*/
+	ppc_md.kbd_init_hw              = rawirkbd_init_hw;
+}
+

arch/ppc/8260_io/Config.in

 #
 # MPC8260 Communication options
 #
+mainmenu_option next_comment
+comment 'MPC8260 Communication Options'
+bool 'Enable SCC Console' CONFIG_SCC_CONSOLE
 if [ "$CONFIG_NET_ETHERNET" = "y" ]; then
   mainmenu_option next_comment
   comment 'MPC8260 Communication Options'
@@ -20,6 +23,13 @@ if [ "$CONFIG_NET_ETHERNET" = "y" ]; then
     bool 'Ethernet on FCC1' CONFIG_FCC1_ENET
     bool 'Ethernet on FCC2' CONFIG_FCC2_ENET
     bool 'Ethernet on FCC3' CONFIG_FCC3_ENET
+    bool 'Use MDIO for PHY configuration' CONFIG_USE_MDIO
+    if [ "$CONFIG_USE_MDIO" = "y" ]; then
+      choice 'Type of PHY'	\
+	"LXT970		CONFIG_FCC_LXT970	\
+	 LXT971		CONFIG_FCC_LXT971	\
+	 QS6612		CONFIG_FCC_QS6612"	CONFIG_FCC_LXT971
+      fi
   fi
-  endmenu
 fi
+endmenu

arch/ppc/8xx_io/Config.in

@@ -25,6 +25,10 @@ if [ "$CONFIG_SMC2_UART" = "y" ]; then
 fi
 bool 'Enable SCC2 and SCC3 for UART' CONFIG_USE_SCC_IO
 
+if [ "$CONFIG_SOUND" = "y" ]; then
+	bool 'Embedded Planet HIOX Audio' CONFIG_HTDMSOUND
+fi
+
 # This doesn't really belong here, but it is convenient to ask
 # 8xx specific questions.
 

arch/ppc/8xx_io/Makefile

-# BK Id: SCCS/s.Makefile 1.6 08/30/01 09:33:48 trini
+# BK Id: %F% %I% %G% %U% %#%
 #
 #
 # Makefile for the linux MPC8xx ppc-specific parts of comm processor
@@ -16,5 +16,6 @@ obj-y			:= commproc.o uart.o
 obj-$(CONFIG_FEC_ENET)	+= fec.o
 obj-$(CONFIG_SCC_ENET)	+= enet.o
 obj-$(CONFIG_UCODE_PATCH) += micropatch.o
+obj-$(CONFIG_HTDMSOUND) += cs4218_tdm.o
 
 include $(TOPDIR)/Rules.make

arch/ppc/8xx_io/commproc.c

 /*
- * BK Id: SCCS/s.commproc.c 1.15 10/16/01 16:21:52 trini
+ * BK Id: %F% %I% %G% %U% %#%
  */
 
 /*
@@ -55,7 +55,63 @@ struct	cpm_action {
 static	struct	cpm_action cpm_vecs[CPMVEC_NR];
 static	void	cpm_interrupt(int irq, void * dev, struct pt_regs * regs);
 static	void	cpm_error_interrupt(void *, struct pt_regs * regs);
+static	void	alloc_host_memory(void);
 
+#if 1
+void
+m8xx_cpm_reset()
+{
+	volatile immap_t	 *imp;
+	volatile cpm8xx_t	*commproc;
+	pte_t			*pte;
+
+	imp = (immap_t *)IMAP_ADDR;
+	commproc = (cpm8xx_t *)&imp->im_cpm;
+
+#ifdef CONFIG_UCODE_PATCH
+	/* Perform a reset.
+	*/
+	commproc->cp_cpcr = (CPM_CR_RST | CPM_CR_FLG);
+
+	/* Wait for it.
+	*/
+	while (commproc->cp_cpcr & CPM_CR_FLG);
+
+	cpm_load_patch(imp);
+#endif
+
+	/* Set SDMA Bus Request priority 5.
+	 * On 860T, this also enables FEC priority 6.  I am not sure
+	 * this is what we realy want for some applications, but the
+	 * manual recommends it.
+	 * Bit 25, FAM can also be set to use FEC aggressive mode (860T).
+	 */
+	imp->im_siu_conf.sc_sdcr = 1;
+
+	/* Reclaim the DP memory for our use.
+	*/
+	dp_alloc_base = CPM_DATAONLY_BASE;
+	dp_alloc_top = dp_alloc_base + CPM_DATAONLY_SIZE;
+
+	/* Tell everyone where the comm processor resides.
+	*/
+	cpmp = (cpm8xx_t *)commproc;
+}
+
+/* We used to do this earlier, but have to postpone as long as possible
+ * to ensure the kernel VM is now running.
+ */
+static void
+alloc_host_memory()
+{
+	uint	physaddr;
+
+	/* Set the host page for allocation.
+	*/
+	host_buffer = (uint)consistent_alloc(GFP_KERNEL, PAGE_SIZE, &physaddr);
+	host_end = host_buffer + PAGE_SIZE;
+}
+#else
 void
 m8xx_cpm_reset(uint host_page_addr)
 {
@@ -111,6 +167,7 @@ m8xx_cpm_reset(uint host_page_addr)
 	*/
 	cpmp = (cpm8xx_t *)commproc;
 }
+#endif
 
 /* This is called during init_IRQ.  We used to do it above, but this
  * was too early since init_IRQ was not yet called.
@@ -222,6 +279,12 @@ m8xx_cpm_dpalloc(uint size)
 	return(retloc);
 }
 
+uint
+m8xx_cpm_dpalloc_index(void)
+{
+	return dp_alloc_base;
+}
+
 /* We also own one page of host buffer space for the allocation of
  * UART "fifos" and the like.
  */
@@ -230,6 +293,11 @@ m8xx_cpm_hostalloc(uint size)
 {
 	uint	retloc;
 
+#if 1
+	if (host_buffer == 0)
+		alloc_host_memory();
+#endif
+
 	if ((host_buffer + size) >= host_end)
 		return(0);
 

arch/ppc/8xx_io/cs4218.h

+#ifndef _cs4218_h_
+/*
+ *  Hacked version of linux/drivers/sound/dmasound/dmasound.h
+ *
+ *
+ *  Minor numbers for the sound driver.
+ *
+ *  Unfortunately Creative called the codec chip of SB as a DSP. For this
+ *  reason the /dev/dsp is reserved for digitized audio use. There is a
+ *  device for true DSP processors but it will be called something else.
+ *  In v3.0 it's /dev/sndproc but this could be a temporary solution.
+ */
+#define _cs4218_h_
+
+#include <linux/types.h>
+#include <linux/config.h>
+
+#define SND_NDEVS	256	/* Number of supported devices */
+#define SND_DEV_CTL	0	/* Control port /dev/mixer */
+#define SND_DEV_SEQ	1	/* Sequencer output /dev/sequencer (FM
+				   synthesizer and MIDI output) */
+#define SND_DEV_MIDIN	2	/* Raw midi access */
+#define SND_DEV_DSP	3	/* Digitized voice /dev/dsp */
+#define SND_DEV_AUDIO	4	/* Sparc compatible /dev/audio */
+#define SND_DEV_DSP16	5	/* Like /dev/dsp but 16 bits/sample */
+#define SND_DEV_STATUS	6	/* /dev/sndstat */
+/* #7 not in use now. Was in 2.4. Free for use after v3.0. */
+#define SND_DEV_SEQ2	8	/* /dev/sequencer, level 2 interface */
+#define SND_DEV_SNDPROC 9	/* /dev/sndproc for programmable devices */
+#define SND_DEV_PSS	SND_DEV_SNDPROC
+
+/* switch on various prinks */
+#define DEBUG_DMASOUND 1
+
+#define MAX_AUDIO_DEV	5
+#define MAX_MIXER_DEV	4
+#define MAX_SYNTH_DEV	3
+#define MAX_MIDI_DEV	6
+#define MAX_TIMER_DEV	3
+
+#define MAX_CATCH_RADIUS	10
+
+#define le2be16(x)	(((x)<<8 & 0xff00) | ((x)>>8 & 0x00ff))
+#define le2be16dbl(x)	(((x)<<8 & 0xff00ff00) | ((x)>>8 & 0x00ff00ff))
+
+#define IOCTL_IN(arg, ret) \
+	do { int error = get_user(ret, (int *)(arg)); \
+		if (error) return error; \
+	} while (0)
+#define IOCTL_OUT(arg, ret)	ioctl_return((int *)(arg), ret)
+
+static inline int ioctl_return(int *addr, int value)
+{
+	return value < 0 ? value : put_user(value, addr);
+}
+
+#define HAS_RECORD
+
+    /*
+     *  Initialization
+     */
+
+/* description of the set-up applies to either hard or soft settings */
+
+typedef struct {
+    int format;		/* AFMT_* */
+    int stereo;		/* 0 = mono, 1 = stereo */
+    int size;		/* 8/16 bit*/
+    int speed;		/* speed */
+} SETTINGS;
+
+    /*
+     *  Machine definitions
+     */
+
+typedef struct {
+    const char *name;
+    const char *name2;
+    void (*open)(void);
+    void (*release)(void);
+    void *(*dma_alloc)(unsigned int, int);
+    void (*dma_free)(void *, unsigned int);
+    int (*irqinit)(void);
+#ifdef MODULE
+    void (*irqcleanup)(void);
+#endif
+    void (*init)(void);
+    void (*silence)(void);
+    int (*setFormat)(int);
+    int (*setVolume)(int);
+    int (*setBass)(int);
+    int (*setTreble)(int);
+    int (*setGain)(int);
+    void (*play)(void);
+    void (*record)(void);		/* optional */
+    void (*mixer_init)(void);		/* optional */
+    int (*mixer_ioctl)(u_int, u_long);	/* optional */
+    int (*write_sq_setup)(void);	/* optional */
+    int (*read_sq_setup)(void);		/* optional */
+    int (*sq_open)(mode_t);		/* optional */
+    int (*state_info)(char *, size_t);	/* optional */
+    void (*abort_read)(void);		/* optional */
+    int min_dsp_speed;
+    int max_dsp_speed;
+    int version ;
+    int hardware_afmts ;		/* OSS says we only return h'ware info */
+					/* when queried via SNDCTL_DSP_GETFMTS */
+    int capabilities ;		/* low-level reply to SNDCTL_DSP_GETCAPS */
+    SETTINGS default_hard ;	/* open() or init() should set something valid */
+    SETTINGS default_soft ;	/* you can make it look like old OSS, if you want to */
+} MACHINE;
+
+    /*
+     *  Low level stuff
+     */
+
+typedef struct {
+    ssize_t (*ct_ulaw)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_alaw)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_s8)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_u8)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_s16be)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_u16be)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_s16le)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+    ssize_t (*ct_u16le)(const u_char *, size_t, u_char *, ssize_t *, ssize_t);
+} TRANS;
+
+
+    /*
+     * Sound queue stuff, the heart of the driver
+     */
+
+struct sound_queue {
+    /* buffers allocated for this queue */
+    int numBufs;		/* real limits on what the user can have */
+    int bufSize;		/* in bytes */
+    char **buffers;
+
+    /* current parameters */
+    int locked ;		/* params cannot be modified when != 0 */
+    int user_frags ;		/* user requests this many */
+    int user_frag_size ;	/* of this size */
+    int max_count;		/* actual # fragments <= numBufs */
+    int block_size;		/* internal block size in bytes */
+    int max_active;		/* in-use fragments <= max_count */
+
+    /* it shouldn't be necessary to declare any of these volatile */
+    int front, rear, count;
+    int rear_size;
+    /*
+     *	The use of the playing field depends on the hardware
+     *
+     *	Atari, PMac: The number of frames that are loaded/playing
+     *
+     *	Amiga: Bit 0 is set: a frame is loaded
+     *	       Bit 1 is set: a frame is playing
+     */
+    int active;
+    wait_queue_head_t action_queue, open_queue, sync_queue;
+    int open_mode;
+    int busy, syncing, xruns, died;
+};
+
+#define SLEEP(queue)		interruptible_sleep_on_timeout(&queue, HZ)
+#define WAKE_UP(queue)		(wake_up_interruptible(&queue))
+
+#endif /* _cs4218_h_ */

arch/ppc/Config.help

@@ -1061,3 +1061,45 @@ CONFIG_XMON
   Include in-kernel hooks for the xmon kernel monitor/debugger
   supported by the PPC port.
 
+CONFIG_ADVANCED_OPTIONS
+  This option will enable prompting for a variety of advanced kernel
+  configuration options.  These options can cause the kernel to not
+  work if they are set incorrectly, but can be used to optimize certain
+  aspects of kernel memory management.
+
+  Unless you know what you are doing you *should not* enable this option.
+
+CONFIG_HIGHMEM_START_BOOL
+  Unless you know what you are doing you *should not* set this option.
+
+  It can be used to override the default PKMAP_BASE address which
+  is the location of the high memory pool.  This can be useful in
+  optimizing virtual memory usage in a system.
+
+CONFIG_LOWMEM_SIZE_BOOL
+  Unless you know what you are doing you *should not* set this option.
+
+  It can be used to override the standard calculated value of
+  MAX_LOW_MEM. This can be useful in optimizing virtual memory usage
+  in a system.
+
+CONFIG_KERNEL_START_BOOL
+  Unless you know what you are doing you *should not* set this option.
+
+  It can be used to override the standard PAGE_OFFSET/KERNELBASE
+  value used by the kernel.  This can be useful in controlling
+  amount of virtual address space available to the kernel.
+
+CONFIG_TASK_SIZE_BOOL
+  Unless you know what you are doing you *should not* set this option.
+
+  It can be used to override the standard TASK_SIZE value used
+  by the kernel.  This can be useful in controlling amount of
+  virtual address space available to user tasks.
+
+CONFIG_BOOT_LOAD_BOOL
+  Unless you know what you are doing you *should not* set this option.
+
+  It can be used to change the initial load address of the zImage or
+  zImage.initrd file.  This can be useful if you are on a board which has
+  a small ammount of memory.

arch/ppc/boot/common/Makefile

@@ -8,18 +8,7 @@
 # Tom Rini	January 2001
 #
 
-.c.s:
-	$(CC) $(CFLAGS) -S -o $*.s $<
-.s.o:
-	$(AS) -o $*.o $<
-.c.o:
-	$(CC) $(CFLAGS) -c -o $*.o $<
-.S.s:
-	$(CPP) $(AFLAGS) -traditional -o $*.o $<
-.S.o:
-	$(CC) $(AFLAGS) -traditional -c -o $*.o $<
-
-OBJCOPY_ARGS = -O elf32-powerpc
+USE_STANDARD_AS_RULE	:= true
 
 coffcrt0.o:
 	$(CC) $(AFLAGS) -DXCOFF -traditional -c -o coffcrt0.o crt0.S