Commit c111e8bf authored by Bjorn Helgaas's avatar Bjorn Helgaas

Merge branches 'pci/host', 'pci/host-designware', 'pci/host-hisi',...

Merge branches 'pci/host', 'pci/host-designware', 'pci/host-hisi', 'pci/host-qcom' and 'pci/host-rcar' into next

* pci/host:
  PCI: host: Add of_pci_get_host_bridge_resources() stub
  PCI: host: Mark PCIe/PCI (MSI) IRQ cascade handlers as IRQF_NO_THREAD

* pci/host-designware:
  PCI: designware: Make config accessor override checking symmetric
  PCI: designware: Simplify control flow

* pci/host-hisi:
  PCI: hisi: Add support for HiSilicon Hip06 PCIe host controllers

* pci/host-qcom:
  ARM: dts: ifc6410: enable PCIe DT node for this board
  ARM: dts: apq8064: add PCIe devicetree node
  PCI: qcom: Add Qualcomm PCIe controller driver
  PCI: qcom: Document PCIe devicetree bindings
  PCI: designware: Ensure ATU is enabled before IO/conf space accesses

* pci/host-rcar:
  PCI: rcar: Add Gen2 PHY setup to pcie-rcar
  PCI: rcar: Add runtime PM support to pcie-rcar
  PCI: rcar: Remove unused pci_sys_data struct from pcie-rcar
HiSilicon PCIe host bridge DT description
HiSilicon Hip05 and Hip06 PCIe host bridge DT description
HiSilicon PCIe host controller is based on Designware PCI core.
It shares common functions with PCIe Designware core driver and inherits
......@@ -7,8 +7,8 @@ Documentation/devicetree/bindings/pci/designware-pci.txt.
Additional properties are described here:
Required properties:
- compatible: Should contain "hisilicon,hip05-pcie".
Required properties
- compatible: Should contain "hisilicon,hip05-pcie" or "hisilicon,hip06-pcie".
- reg: Should contain rc_dbi, config registers location and length.
- reg-names: Must include the following entries:
"rc_dbi": controller configuration registers;
......@@ -20,7 +20,7 @@ Optional properties:
- status: Either "ok" or "disabled".
- dma-coherent: Present if DMA operations are coherent.
Example:
Hip05 Example (note that Hip06 is the same except compatible):
pcie@0xb0080000 {
compatible = "hisilicon,hip05-pcie", "snps,dw-pcie";
reg = <0 0xb0080000 0 0x10000>, <0x220 0x00000000 0 0x2000>;
......
* Qualcomm PCI express root complex
- compatible:
Usage: required
Value type: <stringlist>
Definition: Value should contain
- "qcom,pcie-ipq8064" for ipq8064
- "qcom,pcie-apq8064" for apq8064
- "qcom,pcie-apq8084" for apq8084
- reg:
Usage: required
Value type: <prop-encoded-array>
Definition: Register ranges as listed in the reg-names property
- reg-names:
Usage: required
Value type: <stringlist>
Definition: Must include the following entries
- "parf" Qualcomm specific registers
- "dbi" Designware PCIe registers
- "elbi" External local bus interface registers
- "config" PCIe configuration space
- device_type:
Usage: required
Value type: <string>
Definition: Should be "pci". As specified in designware-pcie.txt
- #address-cells:
Usage: required
Value type: <u32>
Definition: Should be 3. As specified in designware-pcie.txt
- #size-cells:
Usage: required
Value type: <u32>
Definition: Should be 2. As specified in designware-pcie.txt
- ranges:
Usage: required
Value type: <prop-encoded-array>
Definition: As specified in designware-pcie.txt
- interrupts:
Usage: required
Value type: <prop-encoded-array>
Definition: MSI interrupt
- interrupt-names:
Usage: required
Value type: <stringlist>
Definition: Should contain "msi"
- #interrupt-cells:
Usage: required
Value type: <u32>
Definition: Should be 1. As specified in designware-pcie.txt
- interrupt-map-mask:
Usage: required
Value type: <prop-encoded-array>
Definition: As specified in designware-pcie.txt
- interrupt-map:
Usage: required
Value type: <prop-encoded-array>
Definition: As specified in designware-pcie.txt
- clocks:
Usage: required
Value type: <prop-encoded-array>
Definition: List of phandle and clock specifier pairs as listed
in clock-names property
- clock-names:
Usage: required
Value type: <stringlist>
Definition: Should contain the following entries
- "iface" Configuration AHB clock
- clock-names:
Usage: required for ipq/apq8064
Value type: <stringlist>
Definition: Should contain the following entries
- "core" Clocks the pcie hw block
- "phy" Clocks the pcie PHY block
- clock-names:
Usage: required for apq8084
Value type: <stringlist>
Definition: Should contain the following entries
- "aux" Auxiliary (AUX) clock
- "bus_master" Master AXI clock
- "bus_slave" Slave AXI clock
- resets:
Usage: required
Value type: <prop-encoded-array>
Definition: List of phandle and reset specifier pairs as listed
in reset-names property
- reset-names:
Usage: required for ipq/apq8064
Value type: <stringlist>
Definition: Should contain the following entries
- "axi" AXI reset
- "ahb" AHB reset
- "por" POR reset
- "pci" PCI reset
- "phy" PHY reset
- reset-names:
Usage: required for apq8084
Value type: <stringlist>
Definition: Should contain the following entries
- "core" Core reset
- power-domains:
Usage: required for apq8084
Value type: <prop-encoded-array>
Definition: A phandle and power domain specifier pair to the
power domain which is responsible for collapsing
and restoring power to the peripheral
- vdda-supply:
Usage: required
Value type: <phandle>
Definition: A phandle to the core analog power supply
- vdda_phy-supply:
Usage: required for ipq/apq8064
Value type: <phandle>
Definition: A phandle to the analog power supply for PHY
- vdda_refclk-supply:
Usage: required for ipq/apq8064
Value type: <phandle>
Definition: A phandle to the analog power supply for IC which generates
reference clock
- phys:
Usage: required for apq8084
Value type: <phandle>
Definition: List of phandle(s) as listed in phy-names property
- phy-names:
Usage: required for apq8084
Value type: <stringlist>
Definition: Should contain "pciephy"
- <name>-gpios:
Usage: optional
Value type: <prop-encoded-array>
Definition: List of phandle and gpio specifier pairs. Should contain
- "perst-gpios" PCIe endpoint reset signal line
- "wake-gpios" PCIe endpoint wake signal line
* Example for ipq/apq8064
pcie@1b500000 {
compatible = "qcom,pcie-apq8064", "qcom,pcie-ipq8064", "snps,dw-pcie";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */
0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_CLK>;
clock-names = "core", "iface", "phy";
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy";
pinctrl-0 = <&pcie_pins_default>;
pinctrl-names = "default";
};
* Example for apq8084
pcie0@fc520000 {
compatible = "qcom,pcie-apq8084", "snps,dw-pcie";
reg = <0xfc520000 0x2000>,
<0xff000000 0x1000>,
<0xff001000 0x1000>,
<0xff002000 0x2000>;
reg-names = "parf", "dbi", "elbi", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0xff200000 0 0x00100000 /* I/O */
0x82000000 0 0x00300000 0xff300000 0 0x00d00000>; /* memory */
interrupts = <GIC_SPI 243 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 244 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 245 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 247 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 248 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc GCC_PCIE_0_CFG_AHB_CLK>,
<&gcc GCC_PCIE_0_MSTR_AXI_CLK>,
<&gcc GCC_PCIE_0_SLV_AXI_CLK>,
<&gcc GCC_PCIE_0_AUX_CLK>;
clock-names = "iface", "master_bus", "slave_bus", "aux";
resets = <&gcc GCC_PCIE_0_BCR>;
reset-names = "core";
power-domains = <&gcc PCIE0_GDSC>;
vdda-supply = <&pma8084_l3>;
phys = <&pciephy0>;
phy-names = "pciephy";
perst-gpio = <&tlmm 70 GPIO_ACTIVE_LOW>;
pinctrl-0 = <&pcie0_pins_default>;
pinctrl-names = "default";
};
......@@ -8240,11 +8240,19 @@ F: drivers/pci/host/pci-xgene-msi.c
PCIE DRIVER FOR HISILICON
M: Zhou Wang <wangzhou1@hisilicon.com>
M: Gabriele Paoloni <gabriele.paoloni@huawei.com>
L: linux-pci@vger.kernel.org
S: Maintained
F: Documentation/devicetree/bindings/pci/hisilicon-pcie.txt
F: drivers/pci/host/pcie-hisi.c
PCIE DRIVER FOR QUALCOMM MSM
M: Stanimir Varbanov <svarbanov@mm-sol.com>
L: linux-pci@vger.kernel.org
L: linux-arm-msm@vger.kernel.org
S: Maintained
F: drivers/pci/host/*qcom*
PCMCIA SUBSYSTEM
P: Linux PCMCIA Team
L: linux-pcmcia@lists.infradead.org
......
......@@ -47,6 +47,18 @@ mux {
bias-disable;
};
};
pcie_pins: pcie_pinmux {
mux {
pins = "gpio27";
function = "gpio";
};
conf {
pins = "gpio27";
drive-strength = <12>;
bias-disable;
};
};
};
rpm@108000 {
......@@ -123,6 +135,10 @@ pm8921_l23: l23 {
pm8921_lvs1: lvs1 {
bias-pull-down;
};
lvs6 {
bias-pull-down;
};
};
};
......@@ -231,6 +247,16 @@ usb4: usb@12530000 {
status = "okay";
};
pci@1b500000 {
status = "ok";
vdda-supply = <&pm8921_s3>;
vdda_phy-supply = <&pm8921_lvs6>;
vdda_refclk-supply = <&ext_3p3v>;
pinctrl-0 = <&pcie_pins>;
pinctrl-names = "default";
perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
};
qcom,ssbi@500000 {
pmic@0 {
gpio@150 {
......
......@@ -659,5 +659,41 @@ tcsr: syscon@1a400000 {
compatible = "qcom,tcsr-apq8064", "syscon";
reg = <0x1a400000 0x100>;
};
pcie: pci@1b500000 {
compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
reg = <0x1b500000 0x1000
0x1b502000 0x80
0x1b600000 0x100
0x0ff00000 0x100000>;
reg-names = "dbi", "elbi", "parf", "config";
device_type = "pci";
linux,pci-domain = <0>;
bus-range = <0x00 0xff>;
num-lanes = <1>;
#address-cells = <3>;
#size-cells = <2>;
ranges = <0x81000000 0 0 0x0fe00000 0 0x00100000 /* I/O */
0x82000000 0 0 0x08000000 0 0x07e00000>; /* memory */
interrupts = <GIC_SPI 238 IRQ_TYPE_NONE>;
interrupt-names = "msi";
#interrupt-cells = <1>;
interrupt-map-mask = <0 0 0 0x7>;
interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
<0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
<0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
<0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
clocks = <&gcc PCIE_A_CLK>,
<&gcc PCIE_H_CLK>,
<&gcc PCIE_PHY_REF_CLK>;
clock-names = "core", "iface", "phy";
resets = <&gcc PCIE_ACLK_RESET>,
<&gcc PCIE_HCLK_RESET>,
<&gcc PCIE_POR_RESET>,
<&gcc PCIE_PCI_RESET>,
<&gcc PCIE_PHY_RESET>;
reset-names = "axi", "ahb", "por", "pci", "phy";
status = "disabled";
};
};
};
......@@ -173,10 +173,21 @@ config PCIE_ALTERA_MSI
config PCI_HISI
depends on OF && ARM64
bool "HiSilicon SoC HIP05 PCIe controller"
bool "HiSilicon Hip05 and Hip06 SoCs PCIe controllers"
select PCIEPORTBUS
select PCIE_DW
help
Say Y here if you want PCIe controller support on HiSilicon HIP05 SoC
Say Y here if you want PCIe controller support on HiSilicon
Hip05 and Hip06 SoCs
config PCIE_QCOM
bool "Qualcomm PCIe controller"
depends on ARCH_QCOM && OF
select PCIE_DW
select PCIEPORTBUS
help
Say Y here to enable PCIe controller support on Qualcomm SoCs. The
PCIe controller uses the Designware core plus Qualcomm-specific
hardware wrappers.
endmenu
......@@ -21,3 +21,4 @@ obj-$(CONFIG_PCIE_IPROC_BCMA) += pcie-iproc-bcma.o
obj-$(CONFIG_PCIE_ALTERA) += pcie-altera.o
obj-$(CONFIG_PCIE_ALTERA_MSI) += pcie-altera-msi.o
obj-$(CONFIG_PCI_HISI) += pcie-hisi.o
obj-$(CONFIG_PCIE_QCOM) += pcie-qcom.o
......@@ -302,7 +302,8 @@ static int __init dra7xx_add_pcie_port(struct dra7xx_pcie *dra7xx,
}
ret = devm_request_irq(&pdev->dev, pp->irq,
dra7xx_pcie_msi_irq_handler, IRQF_SHARED,
dra7xx_pcie_msi_irq_handler,
IRQF_SHARED | IRQF_NO_THREAD,
"dra7-pcie-msi", pp);
if (ret) {
dev_err(&pdev->dev, "failed to request irq\n");
......
......@@ -522,7 +522,8 @@ static int __init exynos_add_pcie_port(struct pcie_port *pp,
ret = devm_request_irq(&pdev->dev, pp->msi_irq,
exynos_pcie_msi_irq_handler,
IRQF_SHARED, "exynos-pcie", pp);
IRQF_SHARED | IRQF_NO_THREAD,
"exynos-pcie", pp);
if (ret) {
dev_err(&pdev->dev, "failed to request msi irq\n");
return ret;
......
......@@ -537,7 +537,8 @@ static int __init imx6_add_pcie_port(struct pcie_port *pp,
ret = devm_request_irq(&pdev->dev, pp->msi_irq,
imx6_pcie_msi_handler,
IRQF_SHARED, "mx6-pcie-msi", pp);
IRQF_SHARED | IRQF_NO_THREAD,
"mx6-pcie-msi", pp);
if (ret) {
dev_err(&pdev->dev, "failed to request MSI irq\n");
return ret;
......
......@@ -1288,7 +1288,7 @@ static int tegra_pcie_enable_msi(struct tegra_pcie *pcie)
msi->irq = err;
err = request_irq(msi->irq, tegra_pcie_msi_irq, 0,
err = request_irq(msi->irq, tegra_pcie_msi_irq, IRQF_NO_THREAD,
tegra_msi_irq_chip.name, pcie);
if (err < 0) {
dev_err(&pdev->dev, "failed to request IRQ: %d\n", err);
......
......@@ -128,32 +128,26 @@ static inline void dw_pcie_writel_rc(struct pcie_port *pp, u32 val, u32 reg)
static int dw_pcie_rd_own_conf(struct pcie_port *pp, int where, int size,
u32 *val)
{
int ret;
if (pp->ops->rd_own_conf)
ret = pp->ops->rd_own_conf(pp, where, size, val);
else
ret = dw_pcie_cfg_read(pp->dbi_base + where, size, val);
return pp->ops->rd_own_conf(pp, where, size, val);
return ret;
return dw_pcie_cfg_read(pp->dbi_base + where, size, val);
}
static int dw_pcie_wr_own_conf(struct pcie_port *pp, int where, int size,
u32 val)
{
int ret;
if (pp->ops->wr_own_conf)
ret = pp->ops->wr_own_conf(pp, where, size, val);
else
ret = dw_pcie_cfg_write(pp->dbi_base + where, size, val);
return pp->ops->wr_own_conf(pp, where, size, val);
return ret;
return dw_pcie_cfg_write(pp->dbi_base + where, size, val);
}
static void dw_pcie_prog_outbound_atu(struct pcie_port *pp, int index,
int type, u64 cpu_addr, u64 pci_addr, u32 size)
{
u32 val;
dw_pcie_writel_rc(pp, PCIE_ATU_REGION_OUTBOUND | index,
PCIE_ATU_VIEWPORT);
dw_pcie_writel_rc(pp, lower_32_bits(cpu_addr), PCIE_ATU_LOWER_BASE);
......@@ -164,6 +158,12 @@ static void dw_pcie_prog_outbound_atu(struct pcie_port *pp, int index,
dw_pcie_writel_rc(pp, upper_32_bits(pci_addr), PCIE_ATU_UPPER_TARGET);
dw_pcie_writel_rc(pp, type, PCIE_ATU_CR1);
dw_pcie_writel_rc(pp, PCIE_ATU_ENABLE, PCIE_ATU_CR2);
/*
* Make sure ATU enable takes effect before any subsequent config
* and I/O accesses.
*/
dw_pcie_readl_rc(pp, PCIE_ATU_CR2, &val);
}
static struct irq_chip dw_msi_irq_chip = {
......@@ -384,7 +384,7 @@ int dw_pcie_link_up(struct pcie_port *pp)
{
if (pp->ops->link_up)
return pp->ops->link_up(pp);
else
return 0;
}
......@@ -572,6 +572,9 @@ static int dw_pcie_rd_other_conf(struct pcie_port *pp, struct pci_bus *bus,
u64 cpu_addr;
void __iomem *va_cfg_base;
if (pp->ops->rd_other_conf)
return pp->ops->rd_other_conf(pp, bus, devfn, where, size, val);
busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) |
PCIE_ATU_FUNC(PCI_FUNC(devfn));
......@@ -606,6 +609,9 @@ static int dw_pcie_wr_other_conf(struct pcie_port *pp, struct pci_bus *bus,
u64 cpu_addr;
void __iomem *va_cfg_base;
if (pp->ops->wr_other_conf)
return pp->ops->wr_other_conf(pp, bus, devfn, where, size, val);
busdev = PCIE_ATU_BUS(bus->number) | PCIE_ATU_DEV(PCI_SLOT(devfn)) |
PCIE_ATU_FUNC(PCI_FUNC(devfn));
......@@ -659,46 +665,30 @@ static int dw_pcie_rd_conf(struct pci_bus *bus, u32 devfn, int where,
int size, u32 *val)
{
struct pcie_port *pp = bus->sysdata;
int ret;
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0) {
*val = 0xffffffff;
return PCIBIOS_DEVICE_NOT_FOUND;
}
if (bus->number != pp->root_bus_nr)
if (pp->ops->rd_other_conf)
ret = pp->ops->rd_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_rd_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_rd_own_conf(pp, where, size, val);
if (bus->number == pp->root_bus_nr)
return dw_pcie_rd_own_conf(pp, where, size, val);
return ret;
return dw_pcie_rd_other_conf(pp, bus, devfn, where, size, val);
}
static int dw_pcie_wr_conf(struct pci_bus *bus, u32 devfn,
int where, int size, u32 val)
{
struct pcie_port *pp = bus->sysdata;
int ret;
if (dw_pcie_valid_config(pp, bus, PCI_SLOT(devfn)) == 0)
return PCIBIOS_DEVICE_NOT_FOUND;
if (bus->number != pp->root_bus_nr)
if (pp->ops->wr_other_conf)
ret = pp->ops->wr_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_wr_other_conf(pp, bus, devfn,
where, size, val);
else
ret = dw_pcie_wr_own_conf(pp, where, size, val);
if (bus->number == pp->root_bus_nr)
return dw_pcie_wr_own_conf(pp, where, size, val);
return ret;
return dw_pcie_wr_other_conf(pp, bus, devfn, where, size, val);
}
static struct pci_ops dw_pcie_ops = {
......
/*
* PCIe host controller driver for HiSilicon Hip05 SoC
* PCIe host controller driver for HiSilicon SoCs
*
* Copyright (C) 2015 HiSilicon Co., Ltd. http://www.hisilicon.com
*
* Author: Zhou Wang <wangzhou1@hisilicon.com>
* Authors: Zhou Wang <wangzhou1@hisilicon.com>
* Dacai Zhu <zhudacai@hisilicon.com>
* Gabriele Paoloni <gabriele.paoloni@huawei.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
......@@ -16,21 +17,31 @@
#include <linux/of_address.h>
#include <linux/of_pci.h>
#include <linux/platform_device.h>
#include <linux/of_device.h>
#include <linux/regmap.h>
#include "pcie-designware.h"
#define PCIE_SUBCTRL_SYS_STATE4_REG 0x6818
#define PCIE_LTSSM_LINKUP_STATE 0x11
#define PCIE_LTSSM_STATE_MASK 0x3F
#define PCIE_SUBCTRL_SYS_STATE4_REG 0x6818
#define PCIE_SYS_STATE4 0x31c
#define PCIE_HIP06_CTRL_OFF 0x1000
#define to_hisi_pcie(x) container_of(x, struct hisi_pcie, pp)
struct hisi_pcie;
struct pcie_soc_ops {
int (*hisi_pcie_link_up)(struct hisi_pcie *pcie);
};
struct hisi_pcie {
struct regmap *subctrl;
void __iomem *reg_base;
u32 port_id;
struct pcie_port pp;
struct pcie_soc_ops *soc_ops;
};
static inline void hisi_pcie_apb_writel(struct hisi_pcie *pcie,
......@@ -44,7 +55,7 @@ static inline u32 hisi_pcie_apb_readl(struct hisi_pcie *pcie, u32 reg)
return readl(pcie->reg_base + reg);
}
/* Hip05 PCIe host only supports 32-bit config access */
/* HipXX PCIe host only supports 32-bit config access */
static int hisi_pcie_cfg_read(struct pcie_port *pp, int where, int size,
u32 *val)
{
......@@ -67,7 +78,7 @@ static int hisi_pcie_cfg_read(struct pcie_port *pp, int where, int size,
return PCIBIOS_SUCCESSFUL;
}
/* Hip05 PCIe host only supports 32-bit config access */
/* HipXX PCIe host only supports 32-bit config access */
static int hisi_pcie_cfg_write(struct pcie_port *pp, int where, int size,
u32 val)
{
......@@ -94,10 +105,9 @@ static int hisi_pcie_cfg_write(struct pcie_port *pp, int where, int size,
return PCIBIOS_SUCCESSFUL;
}
static int hisi_pcie_link_up(struct pcie_port *pp)
static int hisi_pcie_link_up_hip05(struct hisi_pcie *hisi_pcie)
{
u32 val;
struct hisi_pcie *hisi_pcie = to_hisi_pcie(pp);
regmap_read(hisi_pcie->subctrl, PCIE_SUBCTRL_SYS_STATE4_REG +
0x100 * hisi_pcie->port_id, &val);
......@@ -105,6 +115,23 @@ static int hisi_pcie_link_up(struct pcie_port *pp)
return ((val & PCIE_LTSSM_STATE_MASK) == PCIE_LTSSM_LINKUP_STATE);
}
static int hisi_pcie_link_up_hip06(struct hisi_pcie *hisi_pcie)
{
u32 val;
val = hisi_pcie_apb_readl(hisi_pcie, PCIE_HIP06_CTRL_OFF +
PCIE_SYS_STATE4);
return ((val & PCIE_LTSSM_STATE_MASK) == PCIE_LTSSM_LINKUP_STATE);
}
static int hisi_pcie_link_up(struct pcie_port *pp)
{
struct hisi_pcie *hisi_pcie = to_hisi_pcie(pp);
return hisi_pcie->soc_ops->hisi_pcie_link_up(hisi_pcie);
}
static struct pcie_host_ops hisi_pcie_host_ops = {
.rd_own_conf = hisi_pcie_cfg_read,
.wr_own_conf = hisi_pcie_cfg_write,
......@@ -143,7 +170,9 @@ static int __init hisi_pcie_probe(struct platform_device *pdev)
{
struct hisi_pcie *hisi_pcie;
struct pcie_port *pp;
const struct of_device_id *match;
struct resource *reg;
struct device_driver *driver;
int ret;
hisi_pcie = devm_kzalloc(&pdev->dev, sizeof(*hisi_pcie), GFP_KERNEL);
......@@ -152,6 +181,10 @@ static int __init hisi_pcie_probe(struct platform_device *pdev)
pp = &hisi_pcie->pp;
pp->dev = &pdev->dev;
driver = (pdev->dev).driver;
match = of_match_device(driver->of_match_table, &pdev->dev);
hisi_pcie->soc_ops = (struct pcie_soc_ops *) match->data;
hisi_pcie->subctrl =
syscon_regmap_lookup_by_compatible("hisilicon,pcie-sas-subctrl");
......@@ -180,11 +213,27 @@ static int __init hisi_pcie_probe(struct platform_device *pdev)
return 0;
}
static struct pcie_soc_ops hip05_ops = {
&hisi_pcie_link_up_hip05
};
static struct pcie_soc_ops hip06_ops = {
&hisi_pcie_link_up_hip06
};
static const struct of_device_id hisi_pcie_of_match[] = {
{.compatible = "hisilicon,hip05-pcie",},
{
.compatible = "hisilicon,hip05-pcie",
.data = (void *) &hip05_ops,
},
{
.compatible = "hisilicon,hip06-pcie",
.data = (void *) &hip06_ops,
},
{},
};
MODULE_DEVICE_TABLE(of, hisi_pcie_of_match);
static struct platform_driver hisi_pcie_driver = {
......@@ -196,3 +245,8 @@ static struct platform_driver hisi_pcie_driver = {
};
module_platform_driver(hisi_pcie_driver);
MODULE_AUTHOR("Zhou Wang <wangzhou1@hisilicon.com>");
MODULE_AUTHOR("Dacai Zhu <zhudacai@hisilicon.com>");
MODULE_AUTHOR("Gabriele Paoloni <gabriele.paoloni@huawei.com>");
MODULE_LICENSE("GPL v2");
This diff is collapsed.
......@@ -26,6 +26,7 @@
#include <linux/of_platform.h>
#include <linux/pci.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/slab.h>
#define DRV_NAME "rcar-pcie"
......@@ -94,6 +95,11 @@
#define H1_PCIEPHYDOUTR 0x040014
#define H1_PCIEPHYSR 0x040018
/* R-Car Gen2 PHY */
#define GEN2_PCIEPHYADDR 0x780
#define GEN2_PCIEPHYDATA 0x784
#define GEN2_PCIEPHYCTRL 0x78c
#define INT_PCI_MSI_NR 32
#define RCONF(x) (PCICONF(0)+(x))
......@@ -124,16 +130,7 @@ static inline struct rcar_msi *to_rcar_msi(struct msi_controller *chip)
}
/* Structure representing the PCIe interface */
/*
* ARM pcibios functions expect the ARM struct pci_sys_data as the PCI
* sysdata. Add pci_sys_data as the first element in struct gen_pci so
* that when we use a gen_pci pointer as sysdata, it is also a pointer to
* a struct pci_sys_data.
*/
struct rcar_pcie {
#ifdef CONFIG_ARM
struct pci_sys_data sys;
#endif
struct device *dev;
void __iomem *base;
struct list_head resources;
......@@ -576,6 +573,26 @@ static int rcar_pcie_hw_init_h1(struct rcar_pcie *pcie)
return -ETIMEDOUT;
}
static int rcar_pcie_hw_init_gen2(struct rcar_pcie *pcie)
{
/*
* These settings come from the R-Car Series, 2nd Generation User's
* Manual, section 50.3.1 (2) Initialization of the physical layer.
*/
rcar_pci_write_reg(pcie, 0x000f0030, GEN2_PCIEPHYADDR);
rcar_pci_write_reg(pcie, 0x00381203, GEN2_PCIEPHYDATA);
rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL);
rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL);
rcar_pci_write_reg(pcie, 0x000f0054, GEN2_PCIEPHYADDR);
/* The following value is for DC connection, no termination resistor */
rcar_pci_write_reg(pcie, 0x13802007, GEN2_PCIEPHYDATA);
rcar_pci_write_reg(pcie, 0x00000001, GEN2_PCIEPHYCTRL);
rcar_pci_write_reg(pcie, 0x00000006, GEN2_PCIEPHYCTRL);
return rcar_pcie_hw_init(pcie);
}
static int rcar_msi_alloc(struct rcar_msi *chip)
{
int msi;
......@@ -718,14 +735,16 @@ static int rcar_pcie_enable_msi(struct rcar_pcie *pcie)
/* Two irqs are for MSI, but they are also used for non-MSI irqs */
err = devm_request_irq(&pdev->dev, msi->irq1, rcar_pcie_msi_irq,
IRQF_SHARED, rcar_msi_irq_chip.name, pcie);
IRQF_SHARED | IRQF_NO_THREAD,
rcar_msi_irq_chip.name, pcie);
if (err < 0) {
dev_err(&pdev->dev, "failed to request IRQ: %d\n", err);
goto err;
}
err = devm_request_irq(&pdev->dev, msi->irq2, rcar_pcie_msi_irq,
IRQF_SHARED, rcar_msi_irq_chip.name, pcie);
IRQF_SHARED | IRQF_NO_THREAD,
rcar_msi_irq_chip.name, pcie);
if (err < 0) {
dev_err(&pdev->dev, "failed to request IRQ: %d\n", err);
goto err;
......@@ -915,9 +934,9 @@ static int rcar_pcie_parse_map_dma_ranges(struct rcar_pcie *pcie,
static const struct of_device_id rcar_pcie_of_match[] = {
{ .compatible = "renesas,pcie-r8a7779", .data = rcar_pcie_hw_init_h1 },
{ .compatible = "renesas,pcie-rcar-gen2", .data = rcar_pcie_hw_init },
{ .compatible = "renesas,pcie-r8a7790", .data = rcar_pcie_hw_init },
{ .compatible = "renesas,pcie-r8a7791", .data = rcar_pcie_hw_init },
{ .compatible = "renesas,pcie-rcar-gen2", .data = rcar_pcie_hw_init_gen2 },
{ .compatible = "renesas,pcie-r8a7790", .data = rcar_pcie_hw_init_gen2 },
{ .compatible = "renesas,pcie-r8a7791", .data = rcar_pcie_hw_init_gen2 },
{ .compatible = "renesas,pcie-r8a7795", .data = rcar_pcie_hw_init },
{},
};
......@@ -1003,32 +1022,51 @@ static int rcar_pcie_probe(struct platform_device *pdev)
if (err)
return err;
if (IS_ENABLED(CONFIG_PCI_MSI)) {
err = rcar_pcie_enable_msi(pcie);
if (err < 0) {
dev_err(&pdev->dev,
"failed to enable MSI support: %d\n",
err);
return err;
}
}
of_id = of_match_device(rcar_pcie_of_match, pcie->dev);
if (!of_id || !of_id->data)
return -EINVAL;
hw_init_fn = of_id->data;
pm_runtime_enable(pcie->dev);
err = pm_runtime_get_sync(pcie->dev);
if (err < 0) {
dev_err(pcie->dev, "pm_runtime_get_sync failed\n");
goto err_pm_disable;
}
/* Failure to get a link might just be that no cards are inserted */
err = hw_init_fn(pcie);
if (err) {
dev_info(&pdev->dev, "PCIe link down\n");
return 0;
err = 0;
goto err_pm_put;
}
data = rcar_pci_read_reg(pcie, MACSR);
dev_info(&pdev->dev, "PCIe x%d: link up\n", (data >> 20) & 0x3f);
return rcar_pcie_enable(pcie);
if (IS_ENABLED(CONFIG_PCI_MSI)) {
err = rcar_pcie_enable_msi(pcie);
if (err < 0) {
dev_err(&pdev->dev,
"failed to enable MSI support: %d\n",
err);
goto err_pm_put;
}
}
err = rcar_pcie_enable(pcie);
if (err)
goto err_pm_put;
return 0;
err_pm_put:
pm_runtime_put(pcie->dev);
err_pm_disable:
pm_runtime_disable(pcie->dev);
return err;
}
static struct platform_driver rcar_pcie_driver = {
......
......@@ -279,7 +279,8 @@ static int spear13xx_add_pcie_port(struct pcie_port *pp,
return -ENODEV;
}
ret = devm_request_irq(dev, pp->irq, spear13xx_pcie_irq_handler,
IRQF_SHARED, "spear1340-pcie", pp);
IRQF_SHARED | IRQF_NO_THREAD,
"spear1340-pcie", pp);
if (ret) {
dev_err(dev, "failed to request irq %d\n", pp->irq);
return ret;
......
......@@ -781,7 +781,8 @@ static int xilinx_pcie_parse_dt(struct xilinx_pcie_port *port)
port->irq = irq_of_parse_and_map(node, 0);
err = devm_request_irq(dev, port->irq, xilinx_pcie_intr_handler,
IRQF_SHARED, "xilinx-pcie", port);
IRQF_SHARED | IRQF_NO_THREAD,
"xilinx-pcie", port);
if (err) {
dev_err(dev, "unable to request irq %d\n", port->irq);
return err;
......
......@@ -59,6 +59,13 @@ static inline void of_pci_check_probe_only(void) { }
int of_pci_get_host_bridge_resources(struct device_node *dev,
unsigned char busno, unsigned char bus_max,
struct list_head *resources, resource_size_t *io_base);
#else
static inline int of_pci_get_host_bridge_resources(struct device_node *dev,
unsigned char busno, unsigned char bus_max,
struct list_head *resources, resource_size_t *io_base)
{
return -EINVAL;
}
#endif
#if defined(CONFIG_OF) && defined(CONFIG_PCI_MSI)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment