Commit c1cd0a85 authored by stephen hemminger's avatar stephen hemminger Committed by David S. Miller

sky2: support Yukon EC_U rev B1 and later

Need to change logic to support later versions of Yukon 2 EC_U chip.
Signed-off-by: default avatarStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 9b27105b
......@@ -877,6 +877,10 @@ static void sky2_mac_init(struct sky2_hw *hw, unsigned port)
if (hw->dev[port]->mtu > ETH_DATA_LEN)
reg |= GM_SMOD_JUMBO_ENA;
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
hw->chip_rev == CHIP_REV_YU_EC_U_B1)
reg |= GM_NEW_FLOW_CTRL;
gma_write16(hw, port, GM_SERIAL_MODE, reg);
/* virtual address for data */
......@@ -1413,8 +1417,7 @@ static void sky2_rx_start(struct sky2_port *sky2)
/* These chips have no ram buffer?
* MAC Rx RAM Read is controlled by hardware */
if (hw->chip_id == CHIP_ID_YUKON_EC_U &&
(hw->chip_rev == CHIP_REV_YU_EC_U_A1 ||
hw->chip_rev == CHIP_REV_YU_EC_U_B0))
hw->chip_rev > CHIP_REV_YU_EC_U_A0)
sky2_write32(hw, Q_ADDR(rxq, Q_TEST), F_M_RX_RAM_DIS);
sky2_prefetch_init(hw, rxq, sky2->rx_le_map, RX_LE_SIZE - 1);
......
......@@ -557,6 +557,7 @@ enum yukon_ec_u_rev {
CHIP_REV_YU_EC_U_A0 = 1,
CHIP_REV_YU_EC_U_A1 = 2,
CHIP_REV_YU_EC_U_B0 = 3,
CHIP_REV_YU_EC_U_B1 = 5,
};
enum yukon_fe_rev {
CHIP_REV_YU_FE_A1 = 1,
......@@ -1775,9 +1776,12 @@ enum {
/* GM_SERIAL_MODE 16 bit r/w Serial Mode Register */
enum {
GM_SMOD_DATABL_MSK = 0x1f<<11, /* Bit 15..11: Data Blinder (r/o) */
GM_SMOD_LIMIT_4 = 1<<10, /* Bit 10: 4 consecutive Tx trials */
GM_SMOD_VLAN_ENA = 1<<9, /* Bit 9: Enable VLAN (Max. Frame Len) */
GM_SMOD_JUMBO_ENA = 1<<8, /* Bit 8: Enable Jumbo (Max. Frame Len) */
GM_SMOD_LIMIT_4 = 1<<10, /* 4 consecutive Tx trials */
GM_SMOD_VLAN_ENA = 1<<9, /* Enable VLAN (Max. Frame Len) */
GM_SMOD_JUMBO_ENA = 1<<8, /* Enable Jumbo (Max. Frame Len) */
GM_NEW_FLOW_CTRL = 1<<6, /* Enable New Flow-Control */
GM_SMOD_IPG_MSK = 0x1f /* Bit 4..0: Inter-Packet Gap (IPG) */
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment