ARM: dts: Adjust moxart IRQ controller and flags

The moxart interrupt line flags were not respected in previous
driver: instead of assigning them per-consumer, a fixes mask
was set in the controller.

With the migration to a standard Faraday driver we need to
set up and handle the consumer flags correctly. Also remove
the Moxart-specific flags when switching to using real consumer
flags.

Extend the register window to 0x100 bytes as we may have a few
more registers in there and it doesn't hurt.
Tested-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>

arch/arm/boot/dts/moxart-uc7112lx.dts

@@ -6,7 +6,7 @@
  */
 
 /dts-v1/;
-/include/ "moxart.dtsi"
+#include "moxart.dtsi"
 
 / {
 	model = "MOXA UC-7112-LX";

arch/arm/boot/dts/moxart.dtsi

@@ -6,6 +6,7 @@
  */
 
 /include/ "skeleton.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	compatible = "moxa,moxart";
@@ -36,8 +37,8 @@ soc {
 		ranges;
 
 		intc: interrupt-controller@98800000 {
-			compatible = "moxa,moxart-ic";
-			reg = <0x98800000 0x38>;
+			compatible = "moxa,moxart-ic", "faraday,ftintc010";
+			reg = <0x98800000 0x100>;
 			interrupt-controller;
 			#interrupt-cells = <2>;
 			interrupt-mask = <0x00080000>;
@@ -59,7 +60,7 @@ clk_apb: clk_apb@98100000 {
 		timer: timer@98400000 {
 			compatible = "moxa,moxart-timer";
 			reg = <0x98400000 0x42>;
-			interrupts = <19 1>;
+			interrupts = <19 IRQ_TYPE_EDGE_FALLING>;
 			clocks = <&clk_apb>;
 		};
 
@@ -80,7 +81,7 @@ rtc: rtc {
 		dma: dma@90500000 {
 			compatible = "moxa,moxart-dma";
 			reg = <0x90500080 0x40>;
-			interrupts = <24 0>;
+			interrupts = <24 IRQ_TYPE_LEVEL_HIGH>;
 			#dma-cells = <1>;
 		};
 
@@ -93,7 +94,7 @@ watchdog: watchdog@98500000 {
 		sdhci: sdhci@98e00000 {
 			compatible = "moxa,moxart-sdhci";
 			reg = <0x98e00000 0x5C>;
-			interrupts = <5 0>;
+			interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 			clocks = <&clk_apb>;
 			dmas =  <&dma 5>,
 				<&dma 5>;
@@ -120,7 +121,7 @@ mdio1: mdio@92000090 {
 		mac0: mac@90900000 {
 			compatible = "moxa,moxart-mac";
 			reg = <0x90900000 0x90>;
-			interrupts = <25 0>;
+			interrupts = <25 IRQ_TYPE_LEVEL_HIGH>;
 			phy-handle = <&ethphy0>;
 			phy-mode = "mii";
 			status = "disabled";
@@ -129,7 +130,7 @@ mac0: mac@90900000 {
 		mac1: mac@92000000 {
 			compatible = "moxa,moxart-mac";
 			reg = <0x92000000 0x90>;
-			interrupts = <27 0>;
+			interrupts = <27 IRQ_TYPE_LEVEL_HIGH>;
 			phy-handle = <&ethphy1>;
 			phy-mode = "mii";
 			status = "disabled";
@@ -138,7 +139,7 @@ mac1: mac@92000000 {
 		uart0: uart@98200000 {
 			compatible = "ns16550a";
 			reg = <0x98200000 0x20>;
-			interrupts = <31 8>;
+			interrupts = <31 IRQ_TYPE_LEVEL_HIGH>;
 			reg-shift = <2>;
 			reg-io-width = <4>;
 			clock-frequency = <14745600>;