e1000: delete non NAPI code from the driver

Compile-tested only.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>

Documentation/networking/e1000.txt

@@ -517,17 +517,7 @@ Additional Configurations
 
   NAPI
   ----
-  NAPI (Rx polling mode) is supported in the e1000 driver.  NAPI is enabled
-  or disabled based on the configuration of the kernel.  To override
-  the default, use the following compile-time flags.
-
-  To enable NAPI, compile the driver module, passing in a configuration option:
-
-       make CFLAGS_EXTRA=-DE1000_NAPI install
-
-  To disable NAPI, compile the driver module, passing in a configuration option:
-
-       make CFLAGS_EXTRA=-DE1000_NO_NAPI install
+  NAPI (Rx polling mode) is enabled in the e1000 driver.
 
   See www.cyberus.ca/~hadi/usenix-paper.tgz for more information on NAPI.
 

drivers/net/Kconfig

@@ -1926,20 +1926,6 @@ config E1000
 	  To compile this driver as a module, choose M here. The module
 	  will be called e1000.
 
-config E1000_NAPI
-	bool "Use Rx Polling (NAPI)"
-	depends on E1000
-	help
-	  NAPI is a new driver API designed to reduce CPU and interrupt load
-	  when the driver is receiving lots of packets from the card. It is
-	  still somewhat experimental and thus not yet enabled by default.
-
-	  If your estimated Rx load is 10kpps or more, or if the card will be
-	  deployed on potentially unfriendly networks (e.g. in a firewall),
-	  then say Y here.
-
-	  If in doubt, say N.
-
 config E1000_DISABLE_PACKET_SPLIT
 	bool "Disable Packet Split for PCI express adapters"
 	depends on E1000

drivers/net/e1000/e1000.h

@@ -253,9 +253,7 @@ struct e1000_adapter {
 	u16 link_speed;
 	u16 link_duplex;
 	spinlock_t stats_lock;
-#ifdef CONFIG_E1000_NAPI
 	spinlock_t tx_queue_lock;
-#endif
 	unsigned int total_tx_bytes;
 	unsigned int total_tx_packets;
 	unsigned int total_rx_bytes;
@@ -293,22 +291,16 @@ struct e1000_adapter {
 	bool detect_tx_hung;
 
 	/* RX */
-#ifdef CONFIG_E1000_NAPI
 	bool (*clean_rx)(struct e1000_adapter *adapter,
 			 struct e1000_rx_ring *rx_ring,
 			 int *work_done, int work_to_do);
-#else
-	bool (*clean_rx)(struct e1000_adapter *adapter,
-			 struct e1000_rx_ring *rx_ring);
-#endif
 	void (*alloc_rx_buf)(struct e1000_adapter *adapter,
 			     struct e1000_rx_ring *rx_ring,
 			     int cleaned_count);
 	struct e1000_rx_ring *rx_ring;      /* One per active queue */
-#ifdef CONFIG_E1000_NAPI
 	struct napi_struct napi;
 	struct net_device *polling_netdev;  /* One per active queue */
-#endif
+
 	int num_tx_queues;
 	int num_rx_queues;