Commit c3bc4cae authored by BGardner@Wabtec.com's avatar BGardner@Wabtec.com Committed by Greg Kroah-Hartman

[PATCH] max6875: new i2c device driver

This patch adds support for the MAX6875/MAX6874 chips.
Signed-off-by: default avatarBen Gardner <bgardner@wabtec.com>
Signed-off-by: default avatarGreg Kroah-Hartman <gregkh@suse.de>
parent 20ad93d4
Kernel driver max6875
=====================
Supported chips:
* Maxim max6874, max6875
Prefixes: 'max6875'
Addresses scanned: 0x50, 0x52
Datasheets:
http://pdfserv.maxim-ic.com/en/ds/MAX6874-MAX6875.pdf
Author: Ben Gardner <bgardner@wabtec.com>
Module Parameters
-----------------
* allow_write int
Set to non-zero to enable write permission:
*0: Read only
1: Read and write
Description
-----------
The MAXIM max6875 is a EEPROM-programmable power-supply sequencer/supervisor.
It provides timed outputs that can be used as a watchdog, if properly wired.
It also provides 512 bytes of user EEPROM.
At reset, the max6875 reads the configuration eeprom into its configuration
registers. The chip then begins to operate according to the values in the
registers.
See the datasheet for details on how to program the EEPROM.
Sysfs entries
-------------
eeprom_user - 512 bytes of user-defined EEPROM space. Only writable if
allow_write was set and register 0x43 is 0.
eeprom_config - 70 bytes of config EEPROM. Note that changes will not get
loaded into register space until a power cycle or device reset.
reg_config - 70 bytes of register space. Any changes take affect immediately.
General Remarks
---------------
A typical application will require that the EEPROMs be programmed once and
never altered afterwards.
...@@ -498,4 +498,16 @@ config SENSORS_M41T00 ...@@ -498,4 +498,16 @@ config SENSORS_M41T00
This driver can also be built as a module. If so, the module This driver can also be built as a module. If so, the module
will be called m41t00. will be called m41t00.
config SENSORS_MAX6875
tristate "MAXIM MAX6875 Power supply supervisor"
depends on I2C && EXPERIMENTAL
help
If you say yes here you get support for the MAX6875
EEPROM-Programmable, Hex/Quad, Power-Suppy Sequencers/Supervisors.
This provides a interface to program the EEPROM and reset the chip.
This driver can also be built as a module. If so, the module
will be called max6875.
endmenu endmenu
...@@ -32,6 +32,7 @@ obj-$(CONFIG_SENSORS_LM87) += lm87.o ...@@ -32,6 +32,7 @@ obj-$(CONFIG_SENSORS_LM87) += lm87.o
obj-$(CONFIG_SENSORS_LM90) += lm90.o obj-$(CONFIG_SENSORS_LM90) += lm90.o
obj-$(CONFIG_SENSORS_LM92) += lm92.o obj-$(CONFIG_SENSORS_LM92) += lm92.o
obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o
obj-$(CONFIG_SENSORS_MAX6875) += max6875.o
obj-$(CONFIG_SENSORS_M41T00) += m41t00.o obj-$(CONFIG_SENSORS_M41T00) += m41t00.o
obj-$(CONFIG_SENSORS_PC87360) += pc87360.o obj-$(CONFIG_SENSORS_PC87360) += pc87360.o
obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o obj-$(CONFIG_SENSORS_PCF8574) += pcf8574.o
......
/*
max6875.c - driver for MAX6874/MAX6875
Copyright (C) 2005 Ben Gardner <bgardner@wabtec.com>
Based on i2c/chips/eeprom.c
The MAX6875 has two EEPROM sections: config and user.
At reset, the config EEPROM is read into the registers.
This driver make 3 binary files available in sysfs:
reg_config - direct access to the registers
eeprom_config - acesses configuration eeprom space
eeprom_user - free for application use
In our application, we put device serial & model numbers in user eeprom.
Notes:
1) The datasheet says that register 0x44 / EEPROM 0x8044 should NOT
be overwritten, so the driver explicitly prevents that.
2) It's a good idea to keep the config (0x45) locked in config EEPROM.
You can temporarily enable config writes by changing register 0x45.
This program is free software; you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation; version 2 of the License.
*/
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/module.h>
#include <linux/slab.h>
#include <linux/sched.h>
#include <linux/delay.h>
#include <linux/i2c.h>
#include <linux/i2c-sensor.h>
/* Addresses to scan */
static unsigned short normal_i2c[] = {0x50, 0x52, I2C_CLIENT_END};
static unsigned int normal_isa[] = {I2C_CLIENT_ISA_END};
/* Insmod parameters */
SENSORS_INSMOD_1(max6875);
/* this param will prevent 'accidental' writes to the eeprom */
static int allow_write = 0;
module_param(allow_write, int, 0);
MODULE_PARM_DESC(allow_write,
"Enable write access:\n"
"*0: Read only\n"
" 1: Read/Write access");
/* The MAX6875 can only read/write 16 bytes at a time */
#define SLICE_SIZE 16
#define SLICE_BITS 4
/* CONFIG EEPROM is at addresses 0x8000 - 0x8045, registers are at 0 - 0x45 */
#define CONFIG_EEPROM_BASE 0x8000
#define CONFIG_EEPROM_SIZE 0x0046
#define CONFIG_EEPROM_SLICES 5
/* USER EEPROM is at addresses 0x8100 - 0x82FF */
#define USER_EEPROM_BASE 0x8100
#define USER_EEPROM_SIZE 0x0200
#define USER_EEPROM_SLICES 32
/* MAX6875 commands */
#define MAX6875_CMD_BLOCK_WRITE 0x83
#define MAX6875_CMD_BLOCK_READ 0x84
#define MAX6875_CMD_REBOOT 0x88
enum max6875_area_type {
max6875_register_config=0,
max6875_eeprom_config,
max6875_eeprom_user,
max6857_max
};
struct eeprom_block {
enum max6875_area_type type;
u8 slices;
u32 size;
u32 valid;
u32 base;
unsigned long *updated;
u8 *data;
};
/* Each client has this additional data */
struct max6875_data {
struct i2c_client client;
struct semaphore update_lock;
struct eeprom_block blocks[max6857_max];
/* the above structs point into the arrays below */
u8 data[USER_EEPROM_SIZE + (CONFIG_EEPROM_SIZE*2)];
unsigned long last_updated[USER_EEPROM_SLICES + (CONFIG_EEPROM_SLICES*2)];
};
static int max6875_attach_adapter(struct i2c_adapter *adapter);
static int max6875_detect(struct i2c_adapter *adapter, int address, int kind);
static int max6875_detach_client(struct i2c_client *client);
/* This is the driver that will be inserted */
static struct i2c_driver max6875_driver = {
.owner = THIS_MODULE,
.name = "max6875",
.flags = I2C_DF_NOTIFY,
.attach_adapter = max6875_attach_adapter,
.detach_client = max6875_detach_client,
};
static int max6875_update_slice(struct i2c_client *client,
struct eeprom_block *blk,
int slice)
{
struct max6875_data *data = i2c_get_clientdata(client);
int i, j, addr, count;
u8 rdbuf[SLICE_SIZE];
int retval = 0;
if (slice >= blk->slices)
return -1;
down(&data->update_lock);
if (!(blk->valid & (1 << slice)) ||
(jiffies - blk->updated[slice] > 300 * HZ) ||
(jiffies < blk->updated[slice])) {
dev_dbg(&client->dev, "Starting eeprom update, slice %u, base %u\n",
slice, blk->base);
addr = blk->base + (slice << SLICE_BITS);
count = blk->size - (slice << SLICE_BITS);
if (count > SLICE_SIZE) {
count = SLICE_SIZE;
}
/* Preset the read address */
if (addr < 0x100) {
/* select the register */
if (i2c_smbus_write_byte(client, addr & 0xFF)) {
dev_dbg(&client->dev, "max6875 register select has failed!\n");
retval = -1;
goto exit;
}
} else {
/* select the eeprom */
if (i2c_smbus_write_byte_data(client, addr >> 8, addr & 0xFF)) {
dev_dbg(&client->dev, "max6875 address set has failed!\n");
retval = -1;
goto exit;
}
}
if (i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_READ_I2C_BLOCK)) {
if (i2c_smbus_read_i2c_block_data(client, MAX6875_CMD_BLOCK_READ,
rdbuf) != SLICE_SIZE)
{
retval = -1;
goto exit;
}
memcpy(&blk->data[slice << SLICE_BITS], rdbuf, count);
} else {
for (i = 0; i < count; i++) {
j = i2c_smbus_read_byte(client);
if (j < 0)
{
retval = -1;
goto exit;
}
blk->data[(slice << SLICE_BITS) + i] = (u8) j;
}
}
blk->updated[slice] = jiffies;
blk->valid |= (1 << slice);
}
exit:
up(&data->update_lock);
return retval;
}
static ssize_t max6875_read(struct kobject *kobj, char *buf, loff_t off, size_t count,
enum max6875_area_type area_type)
{
struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj));
struct max6875_data *data = i2c_get_clientdata(client);
struct eeprom_block *blk;
int slice;
blk = &data->blocks[area_type];
if (off > blk->size)
return 0;
if (off + count > blk->size)
count = blk->size - off;
/* Only refresh slices which contain requested bytes */
for (slice = (off >> SLICE_BITS); slice <= ((off + count - 1) >> SLICE_BITS); slice++)
max6875_update_slice(client, blk, slice);
memcpy(buf, &blk->data[off], count);
return count;
}
static ssize_t max6875_user_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_read(kobj, buf, off, count, max6875_eeprom_user);
}
static ssize_t max6875_config_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_read(kobj, buf, off, count, max6875_eeprom_config);
}
static ssize_t max6875_cfgreg_read(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_read(kobj, buf, off, count, max6875_register_config);
}
static ssize_t max6875_write(struct kobject *kobj, char *buf, loff_t off, size_t count,
enum max6875_area_type area_type)
{
struct i2c_client *client = to_i2c_client(container_of(kobj, struct device, kobj));
struct max6875_data *data = i2c_get_clientdata(client);
struct eeprom_block *blk;
int slice, addr, retval;
ssize_t sent = 0;
blk = &data->blocks[area_type];
if (off > blk->size)
return 0;
if ((off + count) > blk->size)
count = blk->size - off;
if (down_interruptible(&data->update_lock))
return -EAGAIN;
/* writing to a register is done with i2c_smbus_write_byte_data() */
if (blk->type == max6875_register_config) {
for (sent = 0; sent < count; sent++) {
addr = off + sent;
if (addr == 0x44)
continue;
retval = i2c_smbus_write_byte_data(client, addr, buf[sent]);
}
} else {
int cmd, val;
/* We are writing to EEPROM */
for (sent = 0; sent < count; sent++) {
addr = blk->base + off + sent;
cmd = addr >> 8;
val = (addr & 0xff) | (buf[sent] << 8); // reversed
if (addr == 0x8044)
continue;
retval = i2c_smbus_write_word_data(client, cmd, val);
if (retval) {
goto error_exit;
}
/* A write takes up to 11 ms */
msleep(11);
}
}
/* Invalidate the scratch buffer */
for (slice = (off >> SLICE_BITS); slice <= ((off + count - 1) >> SLICE_BITS); slice++)
blk->valid &= ~(1 << slice);
error_exit:
up(&data->update_lock);
return sent;
}
static ssize_t max6875_user_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_write(kobj, buf, off, count, max6875_eeprom_user);
}
static ssize_t max6875_config_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_write(kobj, buf, off, count, max6875_eeprom_config);
}
static ssize_t max6875_cfgreg_write(struct kobject *kobj, char *buf, loff_t off, size_t count)
{
return max6875_write(kobj, buf, off, count, max6875_register_config);
}
static struct bin_attribute user_eeprom_attr = {
.attr = {
.name = "eeprom_user",
.mode = S_IRUGO | S_IWUSR | S_IWGRP,
.owner = THIS_MODULE,
},
.size = USER_EEPROM_SIZE,
.read = max6875_user_read,
.write = max6875_user_write,
};
static struct bin_attribute config_eeprom_attr = {
.attr = {
.name = "eeprom_config",
.mode = S_IRUGO | S_IWUSR,
.owner = THIS_MODULE,
},
.size = CONFIG_EEPROM_SIZE,
.read = max6875_config_read,
.write = max6875_config_write,
};
static struct bin_attribute config_register_attr = {
.attr = {
.name = "reg_config",
.mode = S_IRUGO | S_IWUSR,
.owner = THIS_MODULE,
},
.size = CONFIG_EEPROM_SIZE,
.read = max6875_cfgreg_read,
.write = max6875_cfgreg_write,
};
static int max6875_attach_adapter(struct i2c_adapter *adapter)
{
return i2c_detect(adapter, &addr_data, max6875_detect);
}
/* This function is called by i2c_detect */
static int max6875_detect(struct i2c_adapter *adapter, int address, int kind)
{
struct i2c_client *new_client;
struct max6875_data *data;
int err = 0;
/* There are three ways we can read the EEPROM data:
(1) I2C block reads (faster, but unsupported by most adapters)
(2) Consecutive byte reads (100% overhead)
(3) Regular byte data reads (200% overhead)
The third method is not implemented by this driver because all
known adapters support at least the second. */
if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_READ_BYTE_DATA |
I2C_FUNC_SMBUS_BYTE |
I2C_FUNC_SMBUS_WRITE_BYTE_DATA))
goto exit;
/* OK. For now, we presume we have a valid client. We now create the
client structure, even though we cannot fill it completely yet.
But it allows us to access eeprom_{read,write}_value. */
if (!(data = kmalloc(sizeof(struct max6875_data), GFP_KERNEL))) {
err = -ENOMEM;
goto exit;
}
memset(data, 0, sizeof(struct max6875_data));
new_client = &data->client;
i2c_set_clientdata(new_client, data);
new_client->addr = address;
new_client->adapter = adapter;
new_client->driver = &max6875_driver;
new_client->flags = 0;
/* Setup the user section */
data->blocks[max6875_eeprom_user].type = max6875_eeprom_user;
data->blocks[max6875_eeprom_user].slices = USER_EEPROM_SLICES;
data->blocks[max6875_eeprom_user].size = USER_EEPROM_SIZE;
data->blocks[max6875_eeprom_user].base = USER_EEPROM_BASE;
data->blocks[max6875_eeprom_user].data = data->data;
data->blocks[max6875_eeprom_user].updated = data->last_updated;
/* Setup the config section */
data->blocks[max6875_eeprom_config].type = max6875_eeprom_config;
data->blocks[max6875_eeprom_config].slices = CONFIG_EEPROM_SLICES;
data->blocks[max6875_eeprom_config].size = CONFIG_EEPROM_SIZE;
data->blocks[max6875_eeprom_config].base = CONFIG_EEPROM_BASE;
data->blocks[max6875_eeprom_config].data = &data->data[USER_EEPROM_SIZE];
data->blocks[max6875_eeprom_config].updated = &data->last_updated[USER_EEPROM_SLICES];
/* Setup the register section */
data->blocks[max6875_register_config].type = max6875_register_config;
data->blocks[max6875_register_config].slices = CONFIG_EEPROM_SLICES;
data->blocks[max6875_register_config].size = CONFIG_EEPROM_SIZE;
data->blocks[max6875_register_config].base = 0;
data->blocks[max6875_register_config].data = &data->data[USER_EEPROM_SIZE+CONFIG_EEPROM_SIZE];
data->blocks[max6875_register_config].updated = &data->last_updated[USER_EEPROM_SLICES+CONFIG_EEPROM_SLICES];
/* Init the data */
memset(data->data, 0xff, sizeof(data->data));
/* Fill in the remaining client fields */
strlcpy(new_client->name, "max6875", I2C_NAME_SIZE);
init_MUTEX(&data->update_lock);
/* Verify that the chip is really what we think it is */
if ((max6875_update_slice(new_client, &data->blocks[max6875_eeprom_config], 4) < 0) ||
(max6875_update_slice(new_client, &data->blocks[max6875_register_config], 4) < 0))
goto exit_kfree;
/* 0x41,0x42 must be zero and 0x40 must match in eeprom and registers */
if ((data->blocks[max6875_eeprom_config].data[0x41] != 0) ||
(data->blocks[max6875_eeprom_config].data[0x42] != 0) ||
(data->blocks[max6875_register_config].data[0x41] != 0) ||
(data->blocks[max6875_register_config].data[0x42] != 0) ||
(data->blocks[max6875_eeprom_config].data[0x40] !=
data->blocks[max6875_register_config].data[0x40]))
goto exit_kfree;
/* Tell the I2C layer a new client has arrived */
if ((err = i2c_attach_client(new_client)))
goto exit_kfree;
/* create the sysfs eeprom files with the correct permissions */
if (allow_write == 0) {
user_eeprom_attr.attr.mode &= ~S_IWUGO;
user_eeprom_attr.write = NULL;
config_eeprom_attr.attr.mode &= ~S_IWUGO;
config_eeprom_attr.write = NULL;
config_register_attr.attr.mode &= ~S_IWUGO;
config_register_attr.write = NULL;
}
sysfs_create_bin_file(&new_client->dev.kobj, &user_eeprom_attr);
sysfs_create_bin_file(&new_client->dev.kobj, &config_eeprom_attr);
sysfs_create_bin_file(&new_client->dev.kobj, &config_register_attr);
return 0;
exit_kfree:
kfree(data);
exit:
return err;
}
static int max6875_detach_client(struct i2c_client *client)
{
int err;
err = i2c_detach_client(client);
if (err) {
dev_err(&client->dev, "Client deregistration failed, client not detached.\n");
return err;
}
kfree(i2c_get_clientdata(client));
return 0;
}
static int __init max6875_init(void)
{
return i2c_add_driver(&max6875_driver);
}
static void __exit max6875_exit(void)
{
i2c_del_driver(&max6875_driver);
}
MODULE_AUTHOR("Ben Gardner <bgardner@wabtec.com>");
MODULE_DESCRIPTION("MAX6875 driver");
MODULE_LICENSE("GPL");
module_init(max6875_init);
module_exit(max6875_exit);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment